Samsung BD-H4500 ユーザーマニュアル

ブランド: Samsung

モデル: BD-H4500

カテゴリー: ブルーレイプレーヤー

タイプ: ユーザーマニュアル

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service,

please register your product at

www.samsung.com/register

Blu-ray

™

Disc Player

user manual

BD-H4500

ENGLISH

02520A_BD_H4500_ZK ENG.indd 1 8/13/14 10:50 AM

Safety Information

Warning

•

The slots and openings in the cabinet and

in the back or bottom are provided for

necessary ventilation. To ensure reliable

operation of this apparatus, and to protect it

from overheating, these slots and openings

must never be blocked or covered.

- Do not place this apparatus in a confined

space, such as a bookcase, or built-

in cabinet, unless proper ventilation is

provided.

- Do not place this apparatus near or over

a radiator or heat register, or where it is

exposed to direct sunlight.

- Do not place vessels (vases etc.) containing

water on this apparatus. A water spill can

cause a fire or electric shock.

• Do not expose this apparatus to rain

or place it near water (near a bathtub,

washbowl, kitchen sink, or pool, etc.).

If this apparatus accidentally gets wet,

unplug it and contact an authorized dealer

immediately.

• This apparatus uses batteries. In your

community, there might be environmental

regulations that require you to dispose of

these batteries properly. Please contact

your local authorities for disposal or

recycling information.

• Do not overload wall outlets, extension

cords or adaptors beyond their capacity,

since this can result in fire or electric shock.

• Route power-supply cords so that they

are not likely to be walked on or pinched

by items placed on or against them. Pay

particular attention to cords at the plug

end, at wall outlets, and the point where

they exit from the apparatus.

• To protect this apparatus from a lightning

storm, or when it is left unattended and

unused for long periods of time, unplug

it from the wall outlet and disconnect the

antenna or cable system. This will prevent

damage to the set due to lightning and

power line surges.

• Before connecting the AC power cord

to the DC adaptor outlet, make sure the

voltage designation of the DC adaptor

corresponds to the local electrical supply.

• Never insert anything metallic into the open

parts of this apparatus. Doing so may

create a danger of electric shock.

• To avoid electric shock, never touch the

inside of this apparatus. Only a qualified

technician should open this apparatus.

• Make sure to plug the power cord in until

it is firmly seated. When unplugging the

power cord from a wall outlet, always pull

on the power cord's plug. Never unplug by

pulling on the power cord. Do not touch

the power cord with wet hands.

• If this apparatus does not operate normally

- in particular, if there are any unusual

sounds or smells coming from it - unplug

it immediately and contact an authorized

dealer or service center.

• Maintenance of Cabinet.

- Before connecting other components to

this product, be sure to turn them off.

- If you move your product suddenly from a

cold place to a warm place, condensation

may occur on the operating parts and lens

and cause abnormal disc playback. If this

occurs, unplug the product, wait for two

hours, and then connect the plug to the

power outlet. Then, insert the disc, and try

to play back again.

• Be sure to pull the power plug out of the

outlet if the product is to remain unused or

if you are leaving the house for an extended

period of time (especially when children,

elderly, or disabled people will be left alone

in the house).

- Accumulated dust can cause an electric

shock, an electric leakage, or a fire by

causing the power cord to generate sparks

and heat or the insulation to deteriorate.

•

Contact an authorized service center for

information if you intend to install your

product in a location with heavy dust, high

or low temperatures, high humidity, chemical

substances, or where it will operate 24

hours a day such as in an airport, a train

station, etc. Failing to do so may lead to

serious damage of your product.

• Use only a properly grounded plug and wall

outlet.

- An improper ground may cause electric

shock or equipment damage. (Class l

Equipment only.)

• To turn this apparatus off completely, you

must disconnect it from the wall outlet.

Consequently, the wall outlet and power

plug must be readily accessible at all times.

• Do not allow children to hang on the

product.

• Store the accessories (battery, etc.) in a

location safely out of the reach of children.

• Do not install the product in an unstable

location such as a shaky self, a slanted

floor, or a location exposed to vibration.

• Do not drop or strike the product. If the

product is damaged, disconnect the power

cord and contact a service center.

• To clean this apparatus, unplug the power

cord from the wall outlet and wipe the

product using a soft, dry cloth. Do not

use any chemicals such as wax, benzene,

alcohol, thinners, insecticide, air fresheners,

lubricants, or detergent. These chemicals

can damage the appearance of the product

or erase the printing on the product.

• Do not expose this apparatus to dripping

or splashing. Do not put objects filled with

liquids, such as vases on the apparatus.

• Do not dispose of batteries in a fire.

• Do not plug multiple electric devices into

the same wall socket. Overloading a socket

can cause it to overheat, resulting in a fire.

• There is danger of an explosion if you

replace the batteries used in the remote

with the wrong type of battery. Replace

only with the same or equivalent type.

• WARNING - TO PREVENT

THE SPREAD OF FIRE, KEEP

CANDLES AND OTHER

ITEMS WITH OPEN FLAMES

AWAY FROM THIS PRODUCT

AT ALL TIMES.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE THE COVER (OR BACK). THERE ARE

NO USER SERVICEABLE PARTS INSIDE. REFER ALL

SERVICING TO QUALIFIED PERSONNEL.

This symbol indicates that high voltage

is present inside. It is dangerous to make

any kind of contact with any internal

part of this product.

This symbol indicates that important

literature concerning operation and

maintenance has been included with this

product.

02520A_BD_H4500_ZK ENG.indd 2 8/13/14 10:50 AM

CLASS 1 LASER PRODUCT

This Compact Disc player is classified as a

CLASS 1 LASER product. Use of controls,

adjustments or performance of procedures

other than those specified herein may result in

hazardous radiation exposure.

CAUTION :

• THIS PRODUCT USES AN INVISIBLE

LASER BEAM WHICH CAN CAUSE

HAZARDOUS RADIATION EXPOSURE

IF DIRECTED. BE SURE TO OPERATE

PRODUCT CORRECTLY AS INSTRUCTED.

• THIS PRODUCT UTILIZES A LASER.

USE OF CONTROLS OR ADJUSTMENTS

OR PERFORMANCE OF PROCEDURES

OTHER THAN THOSE SPECIFIED HEREIN

MAY RESULT IN HAZARDOUS RADIATION

EXPOSURE. DO NOT OPEN COVERS

AND DO NOT REPAIR YOURSELF. REFER

SERVICING TO QUALIFIED PERSONNEL.

This product satisfies CE regulations when

shielded cables and connectors are used

to connect the unit to other equipment.

To prevent electromagnetic interference

with electric appliances, such as radios

and televisions, use shielded cables and

connectors for connections.

CLASS 1 LASER PRODUCT

KLASSE 1 LASER PRODUKT

LUOKAN 1 LASER LAITE

KLASS 1 LASER APPARAT

PRODUCTO LÁSER CLASE 1

✎

NOTES

If the Region number of a Blu-ray Disc/DVDs

does not correspond to the Region number of

this product, the product cannot play the disc.

IMPORTANT NOTE

The mains lead on this equipment is supplied

with a molded plug incorporating a fuse. The

value of the fuse is indicated on the pin face

of the plug.

If it requires replacing, a fuse approved to

BS1362 of the same rating must be used.

Never use the plug with the fuse cover omitted

if the cover is detachable. If a replacement fuse

cover is required, it must be of the same colour

as the pin face of the plug. Replacement

covers are available from your dealer.

If the fitted plug is not suitable for the power

points in your house or the cable is not long

enough to reach a power point, you should

obtain a suitable safety approved extension

lead or consult your dealer for assistance.

However, if there is no alternative to cutting

off the plug, remove the fuse and then safely

dispose of the plug. Do not connect the plug

to a mains jack, as there is a risk of shock

hazard from the bared flexible cord.

To disconnect the apparatus from the mains, the

plug must be pulled out from the mains socket,

therefore the mains plug shall be readily operable.

The product unit accompanying this user

manual is licenced under certain intellectual

property rights of certain third parties.

Precautions

Important Safety Instructions

Read these operating instructions carefully

before using the unit. Follow all the safety

instructions listed below.

Keep these operating instructions handy for

future reference.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings.

Install in accordance with the

manufacturer's instructions.

8. Do not install near any heat sources such

as radiators, heat registers, stoves, or

other apparatus (including AV receivers)

that produce heat.

9. Do not defeat the safety purpose of

the polarized or grounding-type plug. A

polarized plug has two blades with one

wider than the other. A grounding type

plug has two blades and a third grounding

prong. The wide blade or the third

prong are provided for your safety. If the

provided plug does not fit into your outlet,

consult an electrician for replacement of

the obsolete outlet.

10. Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where it exits the apparatus.

11. Only use attachments/accessories

specified by the manufacturer.

12. Use only with the cart,

stand, tripod, bracket,

or table specified by

the manufacturer,

or sold with the

apparatus. When

a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning

storms or when unused for long periods

of time.

14. Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as when the power-supply cord or

plug is damaged, liquid has been spilled

or objects have fallen into the apparatus,

the apparatus has been exposed to rain

or moisture, does not operate normally, or

has been dropped.

02520A_BD_H4500_ZK ENG.indd 3 8/13/14 10:50 AM

Contents Getting Started

Before using the User Manual

Disc Types and Contents your player can play

Media Disc Type Details

VIDEO

Blu-ray Disc BD-ROM or BD-RE/-R recorded in the BD-RE format.

DVD-VIDEO

DVD-RW

DVD-R

DVD+RW

DVD+R

DVD-VIDEO, recorded DVD+RW/DVD-RW(V)/DVD-R/+R that have

been recorded and finalized, or a USB storage media containing DivX,

MKV or MP4 contents.

MUSIC

CD-RW/-R,

DVD-RW/-R,

BD-RE/-R

Music recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB

storage media containing MP3 or WMA contents.

PHOTO

CD-RW/-R,

DVD-RW/-R,

BD-RE/-R

Photos recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB

storage media containing JPEG contents.

✎

NOTES

The player may not play certain CD-RW/-R and DVD-R because of the disc type or recording conditions.

If a DVD-RW/-R has not been recorded properly in DVD video format, it will not be playable.

Your player will not play content that has been recorded on a DVD-R at a bit-rate that exceeds 10 Mbps.

Your player will not play content that has been recorded on a BD-R or USB device at a bit rate that exceeds

25 Mbps.

Playback may not work for some types of discs, or when you use specific functions, such as angle change

and aspect ratio adjustment. Information about the discs is written in detail on the disc box. Please refer to

this if necessary.

When you play a BD-J title, loading may take longer than a normal title or some functions may perform

slowly.

Disc types your player cannot play

• HD DVD

• DVD-ROM/PD/

MV, etc

• DVD-RAM

• Super Audio CD

(except CD layer)

•

DVD-RW (VR mode)

•

CVD/CD-ROM/CDV/

CD-G/CD-I/LD

(CD-Gs play audio

only, not graphics.)

• 3.9 GB DVD-R for

Authoring.

SAFETY INFORMATION

Warning ....................................................... 2

Precautions ................................................. 3

GETTING STARTED

Before using the User Manual ......................4

Logos of Discs the player can play .............. 5

Accessories ................................................. 6

Front Panel .................................................. 7

Rear Panel ................................................... 7

Remote Control ........................................... 7

CONNECTIONS

Connecting to a TV ...................................... 8

Connecting to an Audio System .................. 8

SETTINGS

The Initial Settings Procedure....................... 9

Menu Navigation ..........................................9

Accessing the Settings Menu ...................... 9

Display Settings ........................................... 9

Audio Settings ........................................... 10

System Settings ........................................ 11

Language Settings .....................................12

Security Settings........................................ 12

Support Settings .......................................12

MEDIA PLAY

Playing a Commercially Recorded Disc ...... 13

Playing Files on a USB Device ................... 13

Playing a Disc with User Recorded

Content ..................................................... 13

Controlling Video Playback ........................ 14

Controlling Music Playback ........................ 14

Playing Photo Contents ............................. 16

APPENDIX

Troubleshooting ......................................... 16

Specifications ............................................ 17

02520A_BD_H4500_ZK ENG.indd 4 8/13/14 10:50 AM

Region Code

Both players and discs are coded by region.

These regional codes must match for a disc

to play. If the codes do not match, the disc

will not play.

The Region Number for this player is

displayed on the rear panel of the player.

Disc

Type

Region

Code

Area

Blu-ray

Disc

North America, Central

America, South America,

Korea, Japan, Taiwan, Hong

Kong and South East Asia.

Europe, Greenland, French

territories, Middle East, Africa,

Australia and New Zealand.

India, China, Russia, Central

and South Asia.

DVD-

VIDEO

The U.S., U.S. territories and

Canada

Europe, Japan, the Middle

East, Egypt, Africa, Greenland

Taiwan, Korea, the Philippines,

Indonesia, Hong Kong

Mexico, South America,

Central America, Australia,

New Zealand, Pacific Islands,

Caribbean

Russia, Eastern Europe, India,

North Korea, Mongolia

China

Logos of Discs the player can play

Blu-ray Disc DivX

PAL broadcast System in U.K., France, Germany,

etc.

Supported File Formats

Notes on the USB connection

• Your player supports USB storage media,

MP3 players, digital cameras, and USB

card readers.

• The player does not support folder or file

names longer than 128 characters.

• Some USB/External HDD/digital camera

devices may not be compatible with the

player.

• Your player supports the FAT16, FAT32,

and NTFS file systems.

• Connect USB devices directly to the

player’s USB port. Connecting through

a USB cable may cause compatibility

problems.

• Inserting more than one memory device

into a multi-card reader may cause the

reader to operate improperly.

• The player does not support the PTP

protocol.

• Do not disconnect a USB device during a

"loading" process.

• The bigger the image resolution, the longer the image takes to display.

• This player cannot play MP3 files with DRM (Digital Rights Management) downloaded from

commercial sites.

• Your player only supports video with a frame rate under 30fps (frames per second).

• Your player only supports USB Mass Storage Class (MSC) devices such as thumb drives

and USB HDD. (HUB is not supported.)

• Certain USB HDD Devices, multi-card readers and thumb drives may not be compatible with

this player.

•

If some USB devices require excessive power, they may be limited by the circuit safety device.

• If playback from a USB HDD is unstable, provide additional power by plugging the HDD into

a wall socket.

If the problem continues, contact the USB HDD manufacturer.

• SAMSUNG is not responsible for any data file damage or data loss.

• Your player does not support NTFS compressed files, sparse files, or encrypted files.

• You can repair or format a USB device on your Desktop PC. (MS-Windows OS only)

Video File Support

File Extension Container Video Codec Audio Codec Resolution

*.avi

AVI

DivX 3.11/4/5/6

MP3

Dolby Digital

DTS

WMA

PCM

1920x1080

MP4v3

H.264 BP/MP/HP

1920x1080

*.mkv

MKV

VC-1 AP

MP3

Dolby Digital

DTS

1920x1080

H.264 BP/MP/HP

1920x1080

*.wmv

WMV (wmv9)

VC-1 AP

WMA

1920x1080

VC-1 SM

1920x1080

*.mp4

MP4

MP4 (mp4v)

AAC

1920x1080

H.264 BP/MP/HP

1920x1080

*.mpg

*.mpeg

MPEG1

MP1, 2

Dolby Digital

DTS

1920x1080

MPEG2

1920x1080

H.264 BP/MP/HP

1920x1080

*.rmvb

RMVB

RV8/9/10

RV30/40

RealAudio 6

1920x1080

02520A_BD_H4500_ZK ENG.indd 5 8/13/14 10:50 AM

• Limitations

- Even when a file is encoded by a supported codec listed above, the file might not be

played if its content has a problem.

- Normal playback is not guaranteed if the file’s container information is wrong or the file

itself is corrupted.

- Files having a higher Bit rate/frame rate than standard may stutter during sound/video

playback.

- The Seek (skip) function is not available if the file’s index table is damaged.

- Depending on your country, RMVB format may not be supported.

• Video decoder

- Supports up to H.264 Level 4.1 and AVCHD

- Does not support H.264 FMO/ASO/RS and VC1 SP/MP/AP L4

- MPEG4 SP, ASP :

Below 1280 x 720 : 60 frames max

Above 1280 x 720 : 30 frames max

- Does not support GMC 2 or higher

• Audio decoder

- Supports WMA 7, 8, 9 and STD

- Does not support WMA sampling rate of 22050Hz mono.

- AAC: Max sampling rate: 96Khz (8, 11, 12, 16, 22,24, 32,44.1, 48, 64, 88.2, 96)

Max bit rate: 320kbps



Supported DivX subtitle file formats

*.ttxt, *.smi, *.srt, *.sub, *.txt

✎

NOTES

Playback of some DivX, MKV or MP4 file may not be supported depending on their video resolution and

frame rate.

Music File Support

File Extension Container Audio Codec Support Range

*.mp3

MP3 MP3

*.wma

WMA WMA

* Sampling rates (in kHz) - 8, 11, 16, 22, 32, 44.1, 48

* Bit rates - All bit-rates from 5kbps to 355kbps

Picture File Support

File Extension Type Resolution

*.jpg

*.jpeg

*.jpe

JPEG

15360x8640

*.png

PNG

15360x8640

AVCHD (Advanced Video Codec High Definition)

• This player can play back AVCHD format discs. These discs are normally recorded and used

in camcorders.

• The AVCHD format is a high definition digital video camera format.

• The MPEG-4 AVC/H.264 format compresses images with greater efficiency than the

conventional image compressing format.

• Some AVCHD discs use the "x.v.Color" format. This player can play back AVCHD discs that

use "x.v.Color" format.

• "x.v.Color" is a trademark of Sony Corporation.

• "AVCHD" and the AVCHD logo are trademarks of Matsushita Electronic Industrial Co., Ltd.

and Sony Corporation.

✎

NOTES

Some AVCHD format discs may not play, depending on the recording condition.

AVCHD format discs need to be finalized.

"x.v.Color" offers a wider colour range than normal DVD camcorder discs.

Accessories

Check for the supplied accessories shown below.

SCREEN

A-BVIEW

FULLBONUS REPEAT REPEAT

AUDIO HOME SUBTITLE

HDMI Cable

Batteries for Remote

Control (AAA Size)

User Manual Remote Control

02520A_BD_H4500_ZK ENG.indd 6 8/13/14 10:50 AM

Front Panel

USB HOST

REMOTE CONTROL SENSOR

DISC TRAY

PLAY/PAUSE BUTTON

OPEN/CLOSE BUTTON

POWER BUTTON

✎

NOTES

When the player displays the Blu-ray Disc menu, you cannot start the movie by pressing the Play button

on the player or the remote. To play the movie, you must select Play Movie or Start in the disc menu, and

then press the

button.

You can perform software upgrades using the USB Host jack with a USB flash memory stick only.

Rear Panel

HDMI OUT

Remote Control

Tour of the Remote Control

SCREEN

A-BVIEW

FULLBONUS REPEAT REPEAT

AUDIO HOME SUBTITLE

Turn the player on and off.

Allows you to repeat A-B disc.

(This function might be not available or work

not correctly, depends on type of disc or

recording conditions).

Press numeric buttons to operate options.

Press to open and close the disc tray.

Use to enter the disc menu.

Press to skip backwards or forwards.

Press to stop a disc.

Press to use bonusview function.

Return to the previous menu.

These buttons are used both for menus on the

player and also several Blu-ray Disc functions.

Use to select menu items and change menu

values.

Press to use Tools menu.

Use to access various audio functions on a

disc (Blu-ray Disc/DVD).

Press to play a disc.

Press to pause a disc.

Turn the TV on and off.

Press to switch the Blu-ray Disc/DVD's

subtitle language.

Use to enter the popup menu/title menu.

Press to search a disc backwards or

forwards.

Press to move to the home menu.

Press to see the full screen on a TV.

During Blu-ray or DVD disc playback, the full

screen button does not operate.

Press to exit the menu.

Use to display the playback information.

Allows you to repeat a title, chapter, track or

disc. (This function might be not available or

work not correctly, depends on type of disc

or recording conditions).

TV volume adjustment.

After setup, allows you to set the input

source on your TV.

Installing batteries

✎

NOTES

If the remote does not operate properly:

•

Check the polarity (+/–) of the batteries.

•

Check if the batteries are drained.

•

Check if the remote sensor is blocked by obstacles.

•

Check if there is any fluorescent lighting nearby.

CAUTION

Dispose of batteries according to local environmental

regulations. Do not put them in the household trash

Do not dispose of batteries in a fire.

Do not short circuit, disassemble or overheat the batteries.

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

02520A_BD_H4500_ZK ENG.indd 7 8/13/14 10:50 AM

Connections

Connecting to a TV

Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN

jack on your TV.

- Do not connect the power cord to the wall outlet until you have made all the other

connections.

- When you change the connections, turn off all devices before you start.

Audio

Video

✎

NOTES

Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user manual of

your TV.

When you connect the player to your TV using the HDMI cable or to a new TV, and then turn it on for the

first time, the player automatically sets the HDMI output resolution to the highest supported by the TV.

A long HDMI cable may cause screen noise. If this occurs, set HDMI Deep Colour to Off in the menu.

To view video in the HDMI 720p, 1080i, or 1080p output mode, you must use a High speed HDMI cable.

HDMI outputs only a pure digital signal to the TV.

If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise appears on

the screen.

Connecting to an Audio System

You can connect the Blu-ray player to an audio system using illustrated below.

- Do not connect the power cord to the wall outlet until you have made all the other

connections.

- When you change the connections, turn off all devices before you start.

Connecting to an HDMI supported AV receiver

• Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN

jack on your receiver.

• Best quality (Recommended)

Audio

02520A_BD_H4500_ZK ENG.indd 8 8/13/14 10:50 AM

Settings

The Initial Settings Procedure

• The Home screen will not appear if you do not

configure the initial settings.

• The OSD (On Screen Display) may change in this

player after you upgrade the software version.

• The access steps may differ depending on the

menu you selected.

• After the loading process of this product is

finished, the panel buttons and remote control

can be operated.

After you have connected the player to your

TV, turn on the TV and player. When you turn

on the player the first time, the player's Initial

Settings screen appears on the TV. The Initial

Setting procedure lets you set the On Screen

Menu languages and the aspect ratio (screen

size).

✎

NOTES

If you want to display the Initial Setting screen

again to make changes, press the

button

on the top panel of the player for more than 5

seconds with no disc inserted. This resets the

player to its default settings.

After the initial settings process is complete.

you can operate the HDMI-CEC function.

If you want to use the Anynet+(HDMI-CEC)

function to aid in the initial set up process,

please follow the instructions below.

1) Connect the player to an Anynet+(HDMI-

CEC) compliant Samsung TV using HDMI

Cable.

2) Set the Anynet+(HDMI-CEC) feature to On in

both the TV and the player.

3) Set the TV to the Initial Settings Procedure.

If you leave the player in the stop mode for

more than 5 minutes without using it, a screen

saver will appear on your TV. If the player is

left in the screen saver mode for more than 25

minutes, the power will automatically turn off.

Menu Navigation

SCREEN

A-BVIEW

FULLBONUS REPEAT REPEAT

AUDIO HOME SUBTITLE

HOME Button : Press to move to the Home

menu.

RETURN Button :

Return to the previous menu.

(Enter) / DIRECTION Button :

Move the cursor or select an item.

Activate the currently selected item.

Confirm a setting.

EXIT Button : Press to exit the current menu.

• Home Menu

Change Device

Settings

Play disc Photos Videos Music

No disc

Selects Videos.

Selects Music.

Selects Settings.

Selects Change Device.

Selects Play disc.

Selects Photos.

✎

NOTES

The Videos, Photos, and Music options require

that you have an appropriate disc inserted into

the player or a USB flash device attached to

the player.

Accessing the Settings Menu

To access the Settings menu and sub-menus,

follow these steps:

1. Press the POWER button.

The Home Menu appears.

2. Press the ▲▼◄► buttons to select

Settings, and then press the

button.

3. Press the ▲▼ buttons to select the

desired submenu, and then press the

button.

4. Press the ▲▼ buttons to select the

desired item, and then press the

button.

5. Press the EXIT button to exit the menu.

✎

NOTES

The access steps may differ depending on

the menu you selected. The OSD (On Screen

Display) may change in this player after you

upgrade the software version.

Display Settings

You can configure various display options

such as the TV Aspect Ratio, Resolution, etc.

TV Aspect Ratio

Depending on the type of television you have,

you may want to adjust the screen size setting.

✎

NOTES

Depending on the disc type, some aspect

ratios may not be available.

If you select an aspect ratio and option which

is different than the aspect ratio of your

TV screen, the picture might appear to be

distorted.

02520A_BD_H4500_ZK ENG.indd 9 8/13/14 10:50 AM

BD Wise (Samsung TVs only)

BD Wise is Samsung’s latest inter-connectivity

feature.

When you connect a Samsung player and a

Samsung TV with BD Wise to each other via

HDMI, and BD Wise is on in both the player

and TV, the player outputs video at the video

resolution and frame rate of the Blu-ray Disc/

DVDs.

✎

NOTES

When BD Wise is on, the Resolution setting

automatically defaults to BD Wise and BD Wise

appears in the Resolution menu.

If the player is connected to a device that does

not support BD Wise, you cannot use the BD

Wise function.

For proper operation of BD Wise, set the BD

Wise menu of both the player and the TV to

On.

Resolution

Lets you set the output resolution of the

HDMI video signal to Auto, 1080p, 1080i,

720p or 576p/480p. The number indicates

the number of lines of video per frame. The

i and p indicate interlaced and progressive

scan, respectively. The more lines, the higher

the quality.

Resolution according to the output

mode

• Blu-ray Disc/E-contents/Digital Contents

playback

Output

Setup

HDMI / connected

HDMI Mode

Blu-ray Disc

E-contents/

Digital

contents

BD Wise

Resolution of

Blu-ray Disc

1080p

Auto

Max. Resolution

of TV input

Max. Resolution

of TV input

1080p@60F

(Movie Frame : Off)

1080p@60F 1080p@60F

Movie Frame :

Auto (24 fps)

1080p@24F 1080p@24F

1080i 1080i 1080i

720p 720p 720p

576p/480p 576p/480p 576p/480p

• DVD playback

Output

Setup

HDMI / connected

HDMI Mode

BD Wise 576i/480i

Auto Max. Resolution of TV input

1080p 1080p

1080i 1080i

720p 720p

576p/480p 576p/480p

✎

NOTES

If the TV you connected to the player does

not support Movie Frame or the resolution

you selected, the message "If no pictures are

shown after selecting ‘Yes’, please wait for 15

seconds to return to the previous resolution. Do

you want to change the resolution?" appears.

If you select Yes, the TV’s screen will go blank

for 15 seconds, and then the resolution will

revert to the previous resolution automatically.

If the screen stays blank after you have

changed the resolution, remove all discs, and

then press and hold the

button on the

top of the player for more than 5 seconds. All

settings are restored to the factory default.

Follow the steps on the previous page to

access each mode and select the Display

Setup that your TV will support.

When the factory default settings are restored,

all stored user BD data is deleted.

The Blu-ray Disc must have the 24 frame

feature for the player to use the Movie Frame

(24 fps) mode.

Movie Frame (24 fps)

Setting the Movie Frame (24 fps) feature to

Auto allows you to adjust the player’s HDMI

output to 24 frames per second for improved

picture quality.

You can enjoy the Movie Frame (24 fps)

feature only on a TV supporting this frame

rate. You can select Movie Frame only when

the player is in the HDMI 1080p output

resolution modes.

HDMI Colour Format

Lets you set the colour space format for

HDMI output to match the capabilities of the

connected device (TV, monitor, etc).

HDMI Deep Colour

Lets you output video from the HDMI OUT

jack with Deep Colour. Deep Colour provides

more accurate colour reproduction with

greater colour depth.

Progressive Mode

Lets you improve picture quality when viewing

DVDs.

Audio Settings

Digital Output

Lets you select the digital audio output format

that is suitable for your TV or AV Receiver. For

more details, please refer to the Digital Output

Selection table.

02520A_BD_H4500_ZK ENG.indd 10 8/13/14 10:50 AM

Digital Output Selection

Setup PCM

Bitstream

(Unprocessed)

Bitstream

(Re-encoded DTS)

Bitstream

(Re-encoded Dolby D)

Connection HDMI Receiver HDMI Receiver HDMI Receiver

HDMI supported AV

receiver

Audio Stream

on Blu-ray

Disc

PCM Up to 7.1ch PCM Re-encoded DTS

Re-encoded Dolby

Digital *

Dolby Digital PCM 2ch Dolby Digital Re-encoded DTS

Re-encoded Dolby

Digital *

Dolby Digital Plus PCM 2ch Dolby Digital Plus Re-encoded DTS

Re-encoded Dolby

Digital *

Dolby TrueHD PCM 2ch Dolby TrueHD Re-encoded DTS

Re-encoded Dolby

Digital *

DTS PCM 2ch DTS Re-encoded DTS

Re-encoded Dolby

Digital *

DTS-HD High

Resolution Audio

PCM 2ch

DTS-HD High

Resolution Audio

Re-encoded DTS

Re-encoded Dolby

Digital *

DTS-HD Master

Audio

PCM 2ch DTS-HD Master Audio Re-encoded DTS

Re-encoded Dolby

Digital *

Audio Stream

on DVD

PCM PCM 2ch PCM 2ch PCM 2ch PCM 2ch

Dolby Digital PCM 2ch Dolby Digital Dolby Digital Dolby Digital

DTS PCM 2ch DTS DTS DTS

Definition for

Blu-ray Disc

Any

Decodes main feature

audio and BONUSVIEW

audio stream together

into PCM audio and

add Navigation Sound

Effects.

Outputs only main

feature audio stream

so that your AV

receiver can decode

the audio bitstream.

You will not hear

BONUSVIEW audio

and Navigation Sound

Effects.

Decodes main feature

audio and BONUSVIEW

audio stream together

into PCM audio

and add Navigation

Sound Effects, then

re-encodes the

PCM audio into DTS

bitstream

Decodes main feature

audio and BONUSVIEW

audio stream together

into PCM audio and

add Navigation Sound

Effects, then re-

encodes the PCM

audio into Dolby Digital

bitstream

* If Source Stream is 2ch, "Re-encoded Dolby D" Settings are not applied.

Blu-ray Discs may include three audio streams :

- Main Feature Audio : The audio soundtrack of the main feature.

- BONUSVIEW audio : An additional soundtrack such as the director or actor’s commentary.

- Navigation Sound Effects : When you choose a menu navigation selection, a Navigation

Sound Effect may sound. Navigation Sound Effects are different on each Blu-ray Disc.

✎

NOTES

Be sure to select the correct Digital Output or

you will hear no sound or just loud noise.

If the HDMI device (AV receiver, TV) is not

compatible with compressed formats (Dolby

Digital, DTS), the audio signal outputs as PCM.

Regular DVDs do not have BONUSVIEW audio

and Navigation Sound Effects.

Some Blu-ray Discs do not have BONUSVIEW

audio and Navigation Sound Effects.

If you play MPEG audio soundtracks, the audio

signal outputs as PCM regardless of your

Digital Output selections (PCM or Bitstream).

If your TV is not compatible with compressed

multi-channel formats (Dolby Digital, DTS), the

player may output PCM 2ch downmixed audio

even though you selected Bitstream (either Re-

encoded or Unprocessed) in the setup menu.

If your TV is not compatible with PCM sampling

rates over 48kHz, the player may output 48kHz

downsampled PCM audio.

Dynamic Range Control

Lets you apply dynamic range control to

Dolby Digital, Dolby Digital Plus, and Dolby

True HD audio.

• Auto : Automatically controls the dynamic

range of Dolby TrueHD audio, based

on information in the Dolby TrueHD

soundtrack.

Also turns dynamic range control on for

Dolby Digital and Dolby Digital Plus.

• Off :

Leaves the dynamic range uncompressed,

letting you hear the original sound.

• On : Turns dynamic range control on for

all three Dolby formats. Quieter sounds

are made louder and the volume of loud

sounds is reduced.

Downmixing Mode

Lets you select the multi-channel downmix

method that is compatible with your stereo

system. You can choose to have the player

downmix to normal stereo or to surround

compatible stereo.

System Settings

Initial Settings

By using the Initial Settings function, you can

set the language, etc.

For more information about the Initial Settings

function, refer to the Initial Settings section of

this user manual (See page 9).

Quick Start

You can turn on the power quickly by

decreasing the boot time.

✎

NOTES

If this function is set to On, Standby power

consumption will be increased.

Anynet+ (HDMI-CEC)

Anynet+ is a convenient function that offers

linked operations with other Samsung players

that have the Anynet+ feature.

To operate this function, connect this player to

an Anynet+ Samsung TV with an HDMI cable.

With Anynet+ on, you can operate this player

using a Samsung TV remote control and start

disc playback simply by pressing the PLAY

( ) button on the TV’s remote control.

For more information, please see the TV user

manual.

02520A_BD_H4500_ZK ENG.indd 11 8/13/14 10:50 AM

✎

NOTES

This function is not available if the HDMI cable

does not support CEC.

If your Samsung TV has an Anynet+ logo, then

it supports the Anynet+ function.

Depending on your TV, certain HDMI output

resolutions may not work.

Please refer to the user manual of your TV.

After the product was turned off, disconnecting

and connecting the power cable turns it on

automatically. At the moment, it automatically

turns off in about 15 seconds for re-

establishing Anynet+ connection.

For some TV products, if connected to this

product with Anynet+ function, turning the

TV on may display a warning popup message

saying no connection was found. Still, Anynet+

connection is properly established and

available to use.

BD Data Management

Enables you to manage the downloaded

contents you accessed through a Blu-ray disc

and stored on a flash drive.

You can check the device’s information

including the storage size, delete the BD data,

or change the Flash memory device.

✎

NOTES

In the external memory mode, disc playback

may be stopped if you disconnect the USB

device in the middle of playback.

Your player supports the FAT16, FAT32, and

NTFS file systems. We recommend you use

USB devices that support USB 2.0 protocol

with 4 MB/sec or faster read/write speed.

The Resume Play function may not work after

you format the storage device.

The total memory available to BD Data

Management may differ, depending on the

conditions.

DivX® Video On Demand

View DivX® VOD Registration Codes to

purchase and play DivX® VOD contents.

Language Settings

You can select the language you prefer for

the On-Screen menu, disc menu, audio, and

subtitles.

✎

NOTES

The selected language will only appear if it is

supported on the disc.

Security Settings

The default security PIN is 0000. Enter the

default PIN to access the security function if

you haven't created your own PIN. After you

have accessed the security function for the

first time, change the PIN using the Change

PIN function.

BD Parental Rating

Prevents playback of Blu-ray Discs with

specific age ratings unless the 4 digit PIN is

entered.

DVD Parental Rating

This function works in conjunction with DVDs

that have been assigned an age rating or

numeric rating that indicates the maturity

level of the content. These numbers help you

control the types of DVDs that your family can

watch.

Select the rating level you want to set.

For example, if you select Level 6, discs rated

above 6 - Level 7 and 8 - will not play.

A larger number indicates more mature content.

Change PIN

Change the 4-digit password used to access

security functions.

If you forget your password

1. Remove any discs.

2. Press and hold the

button on the top

panel for 5 seconds or more.

All settings will revert to the factory settings.

✎

NOTES

When the factory default settings are restored,

all the user stored BD data will be deleted.

Support Settings

Software Upgrade

The Software Upgrade menu allows you to

upgrade the player’s software for performance

improvements or additional services.

By USB

To upgrade by USB, follow these steps:

1. Visit www.samsung.com/bluraysupport.

2. Download the latest USB software

upgrade zip archive to your computer.

3. Unzip the zip archive to your computer.

You should have a single RUF file with the

same name as the zip file.

4. Copy the RUF file to a USB flash drive.

5. Make sure there is no disc in the player,

and then insert the USB flash drive into

the USB port of the player.

6. In the player’s menu, go to Settings >

Support > Software Upgrade.

7. Select By USB.

✎

NOTES

No disc should be in the product when you

upgrade the software using the USB Host jack.

When the software upgrade is done, check the

software details in the software Upgrade menu.

Do not turn off the player during the software

upgrade. It may cause the player to malfunction.

Software upgrades using the USB Host jack

must be performed with a USB flash memory

stick only.

Contact Samsung

Provides contact information for assistance

with your player.

Reset

Returns all settings to their factory defaults.

02520A_BD_H4500_ZK ENG.indd 12 8/13/14 10:50 AM

Media Play

Playing a Commercially Recorded

Disc

1. Press the

button to open the disc tray.

2. Place a disc gently into the disc tray with

the disc's label facing up.

3. Press the

button to close the disc tray.

Playback starts automatically.

Playing Files on a USB Device

There are two methods you can use to play or

view multimedia files located on a USB device

through your player.

Method 1

1. Turn the player on.

2. Connect the USB device to the USB port

on the front panel of the player. The New

Device Connected pop-up appears.

Change Device

Settings

Play disc Photos Videos Music

No disc

New device connected.

Photos

Videos

Music

123

Move

Enter

Return

✎

NOTES

If the pop-up does not appear, go to Method 2.

3. Use the ▲▼ buttons to select Photos,

Videos or Music, and then press the

button. The Photos, Videos & Music

screen appears listing the content of the

device. Depending on how the contents

is arranged, you will see either folders,

individual files, or both.

✎

NOTES

Even though the player will display folders for

all content types, it will only display files of

the Content Type you selected in Step 3. For

example, if you selected music, you will only

be able to see music files. You can change this

selection by returning to the Photos, Videos &

Music screen and going to Step 3 in Method 2

below.

4. If necessary, use the ▲▼◄► buttons to

select a folder, and then press the

button.

5. Select a file to view or play, and then

press the

button.

6. Press the RETURN button to exit a folder

or the EXIT button to return to the Home

screen.

7. Go to pages 14~16 for instructions that

explain how to control playback of videos,

music, and pictures on a USB device.

Method 2

1. Turn the player on.

2. Connect the USB device to the USB port

on the front panel of the player. Select

Change Device and then press the ▲▼

button to select USB. Press the

button.

Change Device

Settings

Play disc Photos Videos Music

No disc

Change Device

No Disc

123

3. Use the ▲▼◄► buttons to select

Photos, Videos or Music on the Home

screen, and then press the

button.

The Photos, Videos & Music screen

appears listing the content of the device.

Depending on how the contents is

arranged, you will see either folders,

individual files, or both.

✎

NOTES

Even though the player will display folders for

all content types, it will only display files of

the Content Type you selected in Step 3. For

example, if you selected music, you will only

be able to see music files. You can change this

selection by returning to the Photos, Videos &

Music screen and repeating Step 3.

4. If necessary, use the ▲▼◄► buttons to

select a folder, and then press the

button.

5. Use the ▲▼◄► buttons to select a file

to view or play, and then press the

button.

6. Press the RETURN button to exit a folder

or the EXIT button to return to Home

screen.

7. Go to pages 14~16 for instructions that

explain how to control playback of videos,

music, and pictures on a USB device.

✎

NOTES

If you insert a disc when playing a USB

device, the device mode changes to "Disc"

automatically.

Playing a Disc with User Recorded

Content

You can play multimedia files you have

recorded on Blu-ray, DVD, or CD discs.

1. Place a user recorded disc into the disc

tray with the disc’s label facing up, and

then close the tray.

2. Use the ◄► buttons to select the type

of content you want to view or play -

Videos, Photos, or Music - and then

press the

button.

✎

NOTES

Even though the player will display folders for

all content types, it will only display files of

the Content Type you selected in Step 2. For

example, if you selected music, you will only

be able to see music files. You can change this

selection by returning to the Home screen and

repeating Step 2.

3. A screen appears listing the contents of

the disc. Depending on how the contents

are arranged, you will see either folders,

individual files, or both.

4. If necessary, use the ▲▼◄►buttons to

select a folder, and then press the

button.

5. Use the ◄►▲▼ buttons to select a file

to view or play, and then press the

button.

02520A_BD_H4500_ZK ENG.indd 13 8/13/14 10:50 AM

6. Press the RETURN button one or more

times to exit a current screen, exit a folder,

or to return to the Home screen. Press the

EXIT button to return directly to the Home

Screen.

7. Go to pages 14~16 for instructions that

explain how to control playback of videos,

music, and pictures on a disc.

Controlling Video Playback

You can control the playback of video content

located on a Blu-ray disc, DVD, CD or

USB. Depending on the media, some of the

functions described in this manual may not be

available.

During Blu-ray or DVD disc playback, the Full

screen button does not operate.

Buttons on the Remote Control

used for Video Playback

SCREEN

A-BVIEW

FULLBONUS REPEAT REPEAT

AUDIO HOME SUBTITLE

Playback related buttons

The player does not play sound in Search,

Slow or Step mode.

• To return to normal speed playback, press

the

button.

button

Starts playback.

button

Stops playback.

button

Pauses playback.

Fast Motion

Play

During playback, press the

button.

Each time you press the

button, the playback speed

will change.

Slow Motion

Play

In pause mode, press the

button.

Each time you press the

button, the playback speed will

change.

Step Motion

Play

In pause mode, press the

button.

Each time you press the

button, a new frame appears.

Skip Motion

Play

During playback, press the

button.

Each time you press the

button, the disc moves to the

previous or next chapter or file.

Using the disc menu, title menu,

popup menu, and title list

DISC MENU

button

During playback, press this button

to start the disc menu function.

TITLE MENU

button

During playback, press this button

to start the title menu function.

POPUP MENU

button

During playback, press this button

to start the popup menu function.

Controlling Music Playback

You can control the playback of music located

on a Blu-ray disc, DVD, CD or USB device.

Buttons on the Remote Control

used for Music Playback

SCREEN

A-BVIEW

FULLBONUS REPEAT REPEAT

AUDIO HOME SUBTITLE

NUMBER buttons (Audio CD (CD-DA) only) :

During Playlist playback, press the desired

track number.

The selected track is played.

Skip : During playback, press the

button to move to the previous or next file of

the playlist.

button : Stops a track.

Fast Play (Audio CD (CD-DA) only)

During playback, press the

button.

Each time you press the

button,

the playback speed will change.

Pause : Pauses a track.

button : Plays the currently selected

track.

Repeat an Audio CD (CD-DA)/

MP3

1. During Playlist playback, press the

TOOLS button.

Pause c Select Tools

Return

00:08 / 05:57

1/6

TRACK 001