Widex WPT202 ユーザーガイド

GB

ES

FR

IT

JP

SC

US

USER INSTRUCTIONS

WIDEX MBR3D CHARGER

WPT202 model

GB USER INSTRUCTIONS ........................................................................3

ES INSTRUCCIONES DE USO .................................................................21

FR MODE D’EMPLOI .............................................................................39

IT LIBRETTO D’INSTRUZIONI ..............................................................58

JP 取扱説明書 ................................................................................. 76

SC 用户使用手册 .............................................................................95

US USER INSTRUCTIONS .....................................................................113

FCC AND ISED STATEMENTS .................................................................134

2

IMPORTANT SAFETY INFORMATION

Read these pages carefully before you start using your charger.

Keep the charger and other small parts away from children, pets, and

mentally disabled people.

Never expose the charger to temperatures above 50° C (122° F), to pro-

longed sunlight, open flames or ignition sources.

Place the charger upright on a flat, stable surface when charging and

with adequate space around the charger. Do not cover or place near

flammable substances.

Never try to open or repair the charger yourself. Contact your hearing

care professional if you experience defects.

Use only a WPT202 charger with your hearing aids. Use of a charger

not recommended by WSAUD A/S may compromise the system or re-

sult in dangerous situations.

Never leave the charger in direct sunlight and do not immerse it in wa-

ter.

Never insert other objects than your hearing aids in the charging wells.

The power adapter must comply with IEC 60601-1, IEC 62368-1 or

equivalent safety standards acceptable in your region. Always use the

supplied USB cable with a power adapter with a USB-A type socket.

3

YOUR CHARGER

Welcome

Thank you for choosing this product, which is intended to charge the sup-

ported hearing aid(s).

Read these instructions carefully before you start using this device.

NOTE

Your charger may not look exactly like the one illustrated in this booklet. We

reserve the right to make any changes we consider necessary.

The charger at a glance

The charger has a charging well for each hearing aid, and two light indica-

tors that show the charging status of the hearing aids.

1

3

2

4

1. Micro USB port

2. Charging wells

3. Light indicators

4. Hinged cover

4

Operating, storage and transport conditions

Your charger is designed for indoor use. It is sensitive to extreme condi-

tions such as high temperatures, and it should not be operated, stored or

transported in direct sunlight.

Operate the charger within the following conditions:

Minimum Maximum

Temperature 0°C (32°F) 30°C (86°F)

Humidity 10% rH 95% rH

Store and transport the charger within the following conditions:

Minimum Maximum

Temperature -20°C (-4°F) 50°C (122°F)

Humidity 10% rH 95% rH

Atmospheric pressure 750 mbar 1060 mbar

You can find technical data sheets and additional information on your

charger on https://global.widex.com.

5

OPERATING THE CHARGER

Getting ready for use

The cover

Before use, grab the hinged cover on both

sides and lift it upwards.

Then pull it over towards the side with the USB

port.

When you are not using the charger, close the

hinged cover to protect the charging wells.

Simply pull the hinged cover upwards to cover

the top before pressing it down.

6

Power supply

You can connect your charger to different power supplies with 5V DC,

500 mA output:

Use only the included USB cable.

7

Connect the cable to the charger:

1

1. Micro USB port

Power on

When the charger is connected to the power supply, the light indicators

flash white 5 times and then turn off:

The charger is now in standby mode and ready to charge your hearing

aid.

8

Charging the hearing aid

Gently place your hearing aid in the charging well. The hearing aid turns

off automatically.

When connected to power, the charger can charge two hearing aids si-

multaneously; however, each hearing aid can be charged individually, de-

pending on the state of the hearing aid.

This means that if one hearing aid is fully charged and placed in the

charger, it will not charge.

However, if the other hearing aid is not charged, it will charge.

Charging your hearing aid fully will take approximately 4 hours. If you

charge your hearing aid for half an hour, you will have approximately 4

hours of use.

9

Charging indicators

While the charger is detecting the hearing aid, the light indicator turns

solid yellow:

Once the charger has detected the hearing aid, the charging will begin.

The light indicator will flash green to indicate that the hearing aid is low

on battery and less than 40% charged:

10

The light indicator will glow green to indicate that the hearing aid is more

than 40% charged:

The light indicator will turn solid green to indicate that the hearing aid is

100% charged:

After charging

Avoid removing the hearing aids from the charging wells by pulling the

ear wire/tube, as this could damage the connection to the hearing aid.

11

Instead, put your fingers round the hearing aid when removing it from the

charger.

When you remove the hearing aid from the charger, the hearing aid turns

on after a few seconds.

Remember to turn it off if you are not going to use it right away.

Immediately after charging, the hearing aid may temporarily feel warm.

If you are not comfortable with this, wait a few minutes, for the hearing

aid to reach room temperature, before putting the hearing aid on.

Overview of light indicators

Light indicators Status

Flashing white The charger is connected to power

Solid yellow The charger is detecting the hearing

aid

Flashing green The hearing aid is charging

Low battery, less than 40%

Glowing green The hearing aid is charging

Battery more than 40%

Solid green The hearing aid is fully charged

Battery 100% charged

12

Light indicators Status

One indicator flashing red An error occurred during charging

and the charging has stopped

See Troubleshooting

Both indicators flashing red An error occurred during charging

and the charging has stopped

See Troubleshooting

Flashing yellow The temperature of the hearing aid

has become too high during charg-

ing and charging is paused

See Troubleshooting

13

CLEANING

The charger does not generally require cleaning. If necessary, carefully

wipe off the charger with a soft dry cloth.

If you notice any dust in the charging well, gently blow it clean. If this is

not enough, gently clean the charging well with a cotton bud.

To remove earwax from the charger, carefully wipe with a soft cloth with

a bit of mild household detergent.

Never use sharp/pointy objects to clean the charger.

14

TROUBLESHOOTING

These pages contain advice on what to do if your charger does not work

as expected.

Light indicators Possible cause Solution

No lights The charger is not

connected Make sure that the USB

cable is connected to a

power adapter and then

plugged into a wall sock-

et

The hearing aid is not

placed correctly in the

charger

Place the hearing aid

correctly in the charger

One or both

indicators flashing

yellow

The temperature of your

surroundings or of the

hearing aid exceeds a

critical limit and the

charging is paused

The charging will contin-

ue when the temperature

of your surroundings or

the hearing aid has

dropped.

If this happens

continually, find a cooler

place to charge your

hearing aid

One indicator flash-

ing red The charger cannot

recognise the hearing aid Remove the incompatible

hearing aid

15

Light indicators Possible cause Solution

The hearing aid has a

critical error Remove the hearing aid,

disconnect from the pow-

er for 10 seconds and

then try again

If the charger is still

flashing red, contact your

hearing care professional

Both indicators

flashing red The charger has a critical

error Remove the hearing aid,

disconnect from the pow-

er for 10 seconds and

then try again

If the charger is still

flashing red, contact your

hearing care professional

16

REGULATORY INFORMATION

Intended use

The WPT202 model is to be used for charging the supported hearing

aid(s).

EU directives

Directive 2014/53/EU

Hereby, WSAUD A/S declares that the WPT202 is in compliance with the

essential requirements and other relevant provisions of Directive

2014/53/EU.

The WPT202 contains a radio transmitter operating at: 6.78 MHz, 13.4

dBµA/m @ 3 m.

A copy of the Declaration of Conformity according to 2014/53/EU can be

found at

https://global.widex.com/doc

N26346

Information regarding disposal

Do not dispose of hearing aids, hearing aid accessories and chargers with

ordinary household waste.

17

Hearing aids, hearing aid accessories and chargers should be disposed of

at sites intended for electrical waste and electronic equipment, or given to

your hearing care professional for safe disposal.

For returning or shipping the devices, please contact your hearing care

professional.

18

SYMBOLS

Symbols commonly used by WSAUD A/S in medical device labelling

(labels/IFU/etc.)

Symbol Title/Description

Manufacturer

The product is produced by the manufacturer whose name and ad-

dress are stated next to the symbol. If appropriate, the date of manu-

facture may also be stated.

Catalogue number

The product’s catalogue (item) number.

Consult instructions for use

The user instructions contain important cautionary information

(warnings/precautions) and must be read before using the prod-

uct.

Warning

Text marked with a warning symbol must be read before using

the product.

WEEE mark

“Not for general waste”. When a product is to be discarded, it

must be sent to a designated collection point for recycling and re-

covering to prevent the risk of harm to the environment or hu-

man health as a result of the presence of hazardous substances.

19

Symbol Title/Description

CE mark

The product is in conformity with the requirements set out in Eu-

ropean CE marking directives.

RCM mark

The product complies with electrical safety, EMC and radio spectrum

regulatory requirements for products supplied to the Australian or

New Zealand markets.

FCC logo

The product is compliant with relevant USA 47 CFR Rules.

FCC – Federal Communications Commission.

Medical device

Indication that the device is a medical device.

20

ページを読み込んでいます...

Widex WPT202 ユーザーガイド

関連論文

その他の書類