Preface
This product is the clear type dome cover. <WV-QDC101C>
This product is the smoke type dome cover (approx. 30 % of transmittance). <WV-CF5SA>
The latest information about the supported cameras
<Control No.:C0501>
Specifications
Ambient operating
temperature:
-30 °C to +50 °C {-22 °F to 122 °F}
Dimensions:
ø92 mm × 49.3 mm (H) {ø3-5/8 inches} x {1-15/16 inches} (H)
Diameter of the dome : 40.1 mm {1-19/32 inches}
Mass: Approx. 25 g {0.06 lbs}
Finish: Acrylic resin Clear <WV-QDC101C>
Smoke <WV-CF5SA>
• Before attempting to connect or operate this product, please read these instructions carefully.
Precautions
Do not use this product except with suitable cameras.
Failure to observe this may cause a drop resulting in injury or accidents.
Refer installation work or dome cover replacement to the dealer.
Installation work requires technique and experience. Failure to observe this may cause fire, electric
shock, injury, or damage to the product.
Be sure to consult the dealer.
The screws and bolts must be tightened to the specified torque.
Failure to observe this may cause a drop resulting in injury or accidents.
When using this product, also read the “Precautions” described in the operating
instructions for the camera to be attached.
Standard Accessories
Operating instructions (this document) ....................................................................................... 1 pc.
Installation
• When a smoke type dome cover is used, the IR LED irradiation distance and the illuminance
level are lower than for a standard clear type dome cover.
Check the settings after attaching the enclosure.
Enclosure fixing screw
(2 places)
Step2
Step3
Step4
• The dome cover is locked using the enclosure
hooks (3 parts). Remove one hook at a time
while pushing the dome cover inwards.
• Remove the protection film of this
product once. After replacing the
dome cover, attach it again.
• When replacing the dome cover,
be careful not to scratch the
outside or inside of the dome
cover.
IMPORTANT:
• When the enclosure is attached, the camera’s focus may go out of focus. Use the "Auto focus"
function in the setup menu to adjust the focus.
• Remove the protective sheet after installation is complete.
• Use lens cleaning paper (used to clean camera or spectacles lenses) to remove any dirt or
fingerprint on the dome cover.
Attach the enclosure to the camera by following the Installation Guide
of the camera.
0.24 N·m
{0.18 lbf·ft}
Dustproof sheet fixing screw (2 pcs.)
Dustproof sheet
Dome cover
Dustproof sheet
→Step 2
This product
Dustproof sheet fixing screw (2 pcs.)
→Step 2
Step1
• Before attempting to connect or install this product, please read these instructions carefully and
save this manual for future use.
• The external appearance and other parts shown in this manual may differ from the actual product
within the scope that will not interfere with normal use due to improvement of the product.
• Read also the installation guide of the camera to be used.
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting
from failures arising out of improper installation or operation inconsistent with this
documentation.
"<Control No.: C****>" used in these documents should be used to search for information
on our technical information website (https://i-pro.com/global/en/surveillance/training-
support/support/technical-information) and will guide you to the right information.
https://www.i-pro.com/
© i-PRO Co., Ltd. 2022
Cs0521-3053
Printed in China
Operating Instructions
Included Installation Instructions
Dome Cover
Model No. WV-QDC101C
WV-CF5SA
If dome cover fixing method of your camera is different from the above,
please refer to the link on the following product information website.
https://i-pro.com/global/en/surveillance/training-support/
documentation-database-list
