Precaution
Do not use this product except with suitable cameras.
Failure to observe this may cause a drop resulting in injury.
Refer installation work to the dealer.
Installation work requires technique and experiences.
Failure to observe this may cause fire, electric shock, injury, or damage to the product.
Be sure to consult the dealer.
The screws and bolts must be tightened to the specified torque.
Failure to observe this may cause a drop resulting in injury or accidents.
When using this product, also read the “Precautions” described in the operating instruc-
tions for the camera to be attached.
Operating Instructions
Included Installation Instructions
Dome Cover
Model No.
WV-QDC502G
• Before attempting to connect or install this product, please read these instructions carefully and
save this manual for future use.
• The external appearance and other parts shown in this manual may differ from the actual
product within the scope that will not interfere with normal use due to improvement of the
product.
• Read also the installation guide of the camera to be used.
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting
from failures arising out of improper installation or operation inconsistent with this
documentation.
Caution:
• Before attempting to connect or operate this
product, please read these instructions care-
fully.
"<Control No.: C****>" used in these documents should be used to search for information
on our technical information website (https://i-pro.com/global/en/surveillance/training-
support/support/technical-information) and will guide you to the right information.
Preface
This product is the smoke type dome cover (approx. 45 % of transmittance).
The latest information about the supported cameras
<Control No.: C0501>
Specifications
Ambient operating temperature: –50 °C to +60 °C {–58 °F to 140 °F}
Dimensions: ø131 mm × 89 mm (H)
{ø5-5/32 inches × 3-1/2 inches (H)}
Mass: Approx.110g {0.24lbs}
Finish: PC resin, Smoke
Standard accessories
Operating Instructions (this document) ..........................................................................................1 pc.
Dome cover holding plate ...........................................................................................................4 pcs.
Mounting screw ........................................................................................................................ 10 pcs.
(of them, 2 for spare)
Installation
Step 1
Rotate the decorative cover by
approximately 10 degrees
counterclockwise in topneath view.
Remove the decorative cover.
Remove the dome cover holding plate
(4 pcs.).
Caution:
• Use the screwdriver (locally procured) with a
bit length of 75 mm {2-15/16 inches} or
more.
• Dispose of the removed dome cover holding
plates (4 pcs.) and mounting screws (8 pcs.).
Remove the dome cover.
Attach the dome cover (smoke).
Remove the protection film covering outside
the new dome cover.
Keep the removed protection film until using it
upon the installation.
(Handle the new dome cover with care not to
scratch inside and outside.)
Tighten the mounting screws
(accessory) to attach the dome
cover holding plate (accessory).
Caution:
• Use the screwdriver (locally procured) with
a bit length of 75 mm {2-15/16 inches} or
more.
• Tighten the mounting screws from ① to
④ in order in the illustration.
Attach the decorative cover.
Rotate the decorative cover by approximately 10 degrees clockwise in topneath
view.
Attach the protection film that was removed in the step 5 to the surface of the dome cover again.
After completing the installation, remove the protection film.
Install the camera by following the instructions in the Installation Guide of the
camera.
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
Step 9
0.3 N·m
{0.22 lbf·ft}
more than 75 mm
{2-15/16 inches}
© i-PRO Co., Ltd. 2022
Ns0522-0
Printed in China
i-PRO Co., Ltd.
https://www.i-pro.com/
Mounting screw
(8 pcs.) (accessory)
Dome cover
holding plate
(4 pcs.)
(accessory)
more than 75 mm
{2-15/16 inches}
②
①
③④
Projection part
“OPEN” mark
