Other items that are needed (not included)
Cs0622-1122
Printed in China
Universal Camera Mounting Bracket
Model No. WV-QCL102
Operating Instructions
• Before attempting to connect or install this product, please read these instructions carefully and
save this manual for future use.
• The external appearance and other parts shown in this manual may differ from the actual product
within the scope that will not interfere with normal use due to improvement of the product.
Preface
This product is a mounting base for the camera. The camera can be installed by attaching this fix-
ture to the ceiling or wall. Two colors, white and black, are available for installation in consideration
of the surrounding landscape.
The latest information about the supported cameras
<Control No.:C0501>.
The model number is abbreviated in some descriptions in this manual.
Do not use this bracket except with suitable cameras.
Failure to observe this may cause a drop resulting in injury or accidents.
Do not install equipment that exceeds the maximum loading weight.
Failure to observe this may cause a drop resulting in injury or accidents.
Be sure to observe the maximum loading weight.
Refer installation work to the dealer.
Installation work requires technique and experience. Failure to observe this may cause fire, electric
shock, injury, or damage to the product.
Be sure to consult the dealer.
The measures of protection against a fall of this product shall be taken.
Failure to observe this may cause a drop resulting in injury or accidents.
Be sure to install the safety wire.
The screws and bolts must be tightened to the specifi ed torque.
Failure to observe this may cause a drop resulting in injury or accidents.
Install the product securely on an installation surface in accordance with the
installation instructions.
Failure to observe this may cause injury or accidents.
Do not rub the edges of metal parts with your hand.
Failure to observe this may cause injury.
When using this product, also read the “Precautions” described in the operating
instructions for the camera to be attached.
Precautions Installation
i-PRO Co., Ltd. cannot be held responsible for accidents or damages caused by
installation using methods not described in the instruction manual or not using
specified parts. In addition, any malfunction caused by such installation is not covered
by the product warranty.
Caution:
• Before attempting to connect or operate this
product, please read these instructions care-
fully.
Notice:
• This product is not suitable for use in loca-
tions where children are likely to be present.
• Do not install this product in locations where
ordinary persons can easily reach.
• For information about screws and other parts
required for installation, refer to the corre-
sponding section of this document.
Included Installation Instructions Specifications
In order to prevent injury, the product must be securely mounted to an installation
surface according to the Installation Guide.
This product is designed to be used indoors.
This product is not operable outdoors. Do not expose this product to direct sunlight for hours and
do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation,
discoloration and malfunction. Keep this product away from water and moisture.
Make sure to remove this product if it will no longer be used.
Precautions for installation
Standard Accessories
Operating Instructions (this document) ....... 1 pc. Template .................................................... 1 pc.
Refer to the operating instructions of the camera for details on the camera installation
(including the cable connection and adjustment).
Step 1 Preparations
Refer to the operating instructions of the camera for details on installing the safety wire (camera
accessory).
Mounting Screws(M6) or Anchor bolt ........4 pcs.
Hexagonal wrench (3 mm on each side) ... 1 pc.
Mounting Screws(M4) or Anchor bolt ......... 1 pc.
Ambient operating temperature: –50 °C to +60 °C {–58 °F to +140 °F}
Dimensions: Max. diameter: ø120 mm / Height: 130 mm {ø4-23/32 inches ×
5-1/8 inches} (not including camera mounting screw)
Mass: Approx. 240 g {0.53 lbs}
Finish: Aluminum/steel plate, ABS, white / black
Max. loading weight: 2 kg
“<Control No.: C****>” used in these documents should be used to search for
information on our technical information website (https://i-pro.com/global/en/
surveillance/training-support/support/technical-information) and will guide you to
the right information.
© i-PRO Co., Ltd. 2022
i-PRO Co., Ltd.
https://www.i-pro.com/
IMPORTANT
• Minimum pull-out strength: 562 N {126.34 lbf} (per screw)
• For information about the minimum pull-out strength, refer to our technical information web-
site <Control No.: C0120>.
• Select screws according to the material of the location that the camera will be mounted to. In
this case, wood screws and nails should not be used.
Step 2 Machining the installation surface
Camera mounting side>
Step 3
Fixing the bracket
<When wiring from behind the ceiling>
Step 4
Fixing the camera
Turn the hexagonal hole with a hexago-
nal wrench to loosen the fi xation of the
movable part.
Hexagonal wrench (3 mm on each side)
(procured locally)
The following is an illustration of an
indoor box type camera as an example.
Attach the camera to the head portion of this product.
Mounting Screw (4 pcs.) (M6:locally procured)
Minimum pull-out strength:
562 N {126.34 lbf} (per 1 pc.)
Step 5 Put the mounting hole of the mounting chassis
on the anchor bolt.
With power connected to the camera, connect a monitor to the MONITOR OUT terminal to bring
up the screen. For models without a MONITOR OUT terminal, use a PC to connect the camera
to the network and display the shooting screen.
Adjust the camera orientation.
Turn the hexagonal hole with a hexagonal wrench to
tighten the fi xation of the movable part.
Hexagonal wrench (3 mm on each side) (procured
locally)
Step 6
Fixing the safety wire (camera accessory)
Mounting Screw M4:locally procured)
Minimum pull-out strength:
562 N {126.34 lbf} (per 1 pc.)
Flat Washer
(Camera accessory)
Spring Washer
(Camera accessory)
Ceiling
Wall
Note:
• When installing on a wall, rear connec-
tions and cable routing might be diffi-
cult depending on the camera that
used and the orientation of the instal-
lation.
2.7 m
(8.86 ft)
Flat Washer
(Camera accessory)
Spring Washer
(Camera accessory)
Mounting Screw (4 pcs.) (M4:locally
procured)
Minimum pull-out strength:
562 N {126.34 lbf} (per 1 pc.)
Recommended tightening torque:
1.97 N·m {1.45 lbf·ft}
(Max. 2.95 N-m{2.17 lbf·ft})
360°
90°
90°
OPEN
LOCKLOCK
60° 60°
Drill a hole in the center for wiring if necessary.
83.5 mm
{3-9/32 inches}
ø30 mm
{1-3/16 inches}
66.7 mm
{2-5/8 inches}
WV-QCL102
ㄊノヱンヰጋΉ᰷
https://www.i-pro.com/
/