4-154-385-01 (1)
233 237 /
233 to 237 (9
1
/
4
to 9
3
/
8
) hole
/
Ceiling
/
Fixing
plate
10 to 35
(
13
/
32
to 1
7
/
16
)
/
Fixing
plate
: / Unit: mm (inches)
/
Fixing
plate
/
Installation
/
Removal
/
Align
the marks
M4 10 /
M4 supplied screws
/
Align
the marks
( ) /
Protrusion
(round type)
a
a
/
Align
the marks
( ) /
Protrusion
(round type)
a
a
/
Inner cover
/
Screw
/
Screw
226 (9)
ø270 (10
3
/
4
)
112.1 (4
1
/
2
)
152.1 (6)
23.8 (
15
/
16
)
115.5 (4
5
/
8
)
/ Unit: mm (inches)
ø270 (10
3
/
4
)
20.8 (
27
/
32
)
120.5 (4
3
/
4
)
/ Unit: mm (inches)
1
YT-ICB124 SNC-RH124 RS46N/RS46P RS44N/
RS44P
10 35 mm
YT-LD124C/LD124S YT-ICB124( )
(YT-ICB124)
YT-ICB124( )
YT-LD124C/LD124S(YT-ICB124 )
1
YT-LD124C/LD124S(YT-ICB124 )
40
YT-ICB124( )
1
235 2 mm
4
2
(
)
( )
)
3
(
)
1.0 N m (10 kgf cm)
4
5
6
M4 10
(
)
7
LOCK
8
(
)
YT-LD124C/LD-124S YT-
LD124C/LD-124S(YT-ICB124 )
V
V
YT-LD124C/LD124S(YT-ICB124 )
1
V
V
2
3
YT-ICB124( )
1
2
a
3
4
5
6
7
1.0 N m (10 kgf cm)
YT-LD124C/LD124S(YT-ICB124 )
1
2
a
YT-ICB124( )
930 g( )
(1)
M4 10 (3)
(1)
( ) YT-LD124C
( ) YT-LD124S
YT-LD124C/LD124S(YT-ICB124 )
400 g
(1)
English
WARNING
This installation should be made by a qualified service person and
should conform to all local codes.
Ensure that the installation location and its material are strong
enough to withstand the gross weight of the camera and the In-
Ceiling Bracket, and then install the camera securely. If they are not
strong enough, the camera may fall and cause serious injury.
To prevent the camera from falling, be sure to attach the wire rope
supplied with the camera.
If you install the camera at a height, check periodically, at least once
a year, to ensure that the connection has not loosened. If conditions
warrant, perform this periodic check more frequently.
Overview
YT-ICB124 is the special package for SNC-RH124/RS46N/RS46P/RS44N/RS44P.
It is used when the body of the camera is embedded in the ceiling, or with
gypsum boards and such where the material used in the ceiling is too fragile
to hold ordinary screws.
Install the camera on the ceiling with the thickness from 10 mm to 35 mm
(
13
/
32
~ 1
7
/
16
inches) inclusive.
YT-LD124C/LD124S is the dedicated dome cover for YT-ICB124 (In-ceiling
kit).
When using this dome cover, the in-ceiling kit (YT-ICB124) is required.
Notes
YT-ICB124 (In-ceiling kit) is for indoor use. It cannot be used for installation
outdoors.
Using YT-LD124C/LD124S (dedicated dome cover for YT-ICB124) may
cause deterioration of the camera’s optical performance due to image
distortion and luminous spots, etc. If you use a grey-smoke dome cover,
the brightness of the screen becomes darker by about 1 aperture.
Do not use YT-LD124C/LD124S (dedicated dome cover for YT-ICB124)
attached in a place where the temperature becomes more than 40°C
(104°F).
Installing
YT-ICB124 (In-ceiling kit)
1
Make a ø235 ± 2 mm (9
3
/
8
±
3
/
32
inches) hole in the ceiling.
Use the supplied template.
Use the four slotted holes on the template to decide the center position
of the camera.
2
Fix the in-ceiling bracket to the ceiling with an anchor bolt (anchor bolt
is not supplied).
Make sure that the fixing plates on both sides of the bracket are in the
lengthwise position (factory default), and install the bracket in the hole
in the ceiling. ()
The ¯ hole in the bracket shows the front side of the camera.
Adjust the direction when attaching the in-ceiling kit as necessary.
3
Tighten the left and right screws of the bracket. The bracket should grip
the ceiling.
As you tighten the screws, the fixing plates swing outward and open.
When you tighten the screws further, the fixing plates swing lower and
grip the ceiling. ()
Ensure that the fixing plates are gripping the ceiling firmly.
Note
Torque the screws to 1.0 N•m (10 kgf•cm) or less to tighten them.
Tightening the screws too much may cause damage to the in-ceiling
bracket.
4
Connect the cable and the ceiling unit wire rope to the ceiling unit of
the camera.
¿ For details, see the Installation Manual of the camera.
5
When you insert the ceiling unit into the bracket completely, the arm
temporarily supports the ceiling unit.
Position the ¯ hole in the bracket (indicating the front) and the
front side mark on the ceiling unit.
Match the protrusions of the bracket with the holes in the ceiling
unit. Make sure that the protrusions fit the holes.
Align the holes in the ceiling unit with the screw holes in the
bracket.
6
Using the supplied M4Ï10 screws, attach the ceiling unit of the
camera to the in-ceiling bracket. ()
Warning
Always fix with the supplied screws. Using screws other than those
supplied may cause the camera to fall, which may cause serious
injury.
Using the device with temporary fixture may result in the camera
falling, which may cause serious injury.
7
Insert the camera into the ceiling unit until you hear a click.
Push the Lock button to confirm the camera is locked.
¿ For details, see the Installation Manual of the camera.
8
Attach the cover (supplied). ()
See the “YT-LD124C/LD124S (dedicated dome cover for YT-ICB124)” to
install the purchased dome cover.
Place the cover over the in-ceiling bracket and turn the cover
clockwise to fix it.
When installing the cover, match the right protrusion (square type)
on the cover with the notch in the bracket. Then turn the cover
clockwise until the left protrusion (round type) meets the notch.
Secure the cover with screws.
YT-LD124C/LD124S (dedicated dome cover for YT-ICB124)
Remove the inner cover for a wider area view.
Note
The lens zoom and angle may result in a blurred or inclined image of the
area covered by inner cover.
1
Place the dome cover over the in-ceiling bracket and turn the cover
clockwise to fix it.
When installing the cover, position the right protrusion (square type) of
the dome over the notch in the bracket. Then turn the cover clockwise
until the left protrusion (round type) meets the notch.
2
Secure the dome cover with screws.
3
Remove the protective sheet on the dome cover.
In-Ceiling Bracket
Dome Cover Clear
Dome Cover Smoked
Installation Instructions
Manuel d’installation
Manual de instalación
YT-ICB124(In-Ceiling Bracket)
YT-LD124C(Dome Cover Clear)
YT-LD124S(Dome Cover Smoked)
© 2009 Sony Corporation Printed in China
ページを読み込んでいます...
/