Pioneer X-CM52BT 取扱説明書

X-CM52BT-K/-W

DVD Receiver System

ŅŗŅġ௦ԞᏣقಜ

Operating Instructions

X-CM52_LXE_En.book 1 ページ２０１４年３月２８日　金曜日　午前１０時３９分

WARNING

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

liquid near this equipment (such as a vase or flower

pot) or expose it to dripping, splashing, rain or

moisture.

D3-4-2-1-3_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c*_A1_En

This product is for general household purposes. Any

failure due to use for other than household purposes

(such as long-term use for business purposes in a

restaurant or use in a car or ship) and which requires

repair will be charged for even during the warranty

period.

K041_A1_En

CAUTION

This product is a class 1 laser product classified

under the Safety of laser products, IEC 60825-1:2007.

CLASS 1 LASER PRODUCT

D58-5-2-2a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat radiation

(at least 25 cm at top, 15 cm at rear, and 5 cm at each

side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire

hazard, the openings should never be blocked or

covered with items (such as newspapers, table-cloths,

curtains) or by operating the equipment on thick carpet

or a bed.

D3-4-2-1-7b*_A1_En

CAUTION

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

D3-4-2-1-1_B1_En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the

plug by tugging the cord and never touch the power

cord when your hands are wet as this could cause a

short circuit or electric shock. Do not place the unit, a

piece of furniture, etc., on the power cord, or pinch the

cord. Never make a knot in the cord or tie it with other

cords. The power cords should be routed such that they

are not likely to be stepped on. A damaged power cord

can cause a fire or give you an electrical shock. Check

the power cord once in a while. When you find it

damaged, ask your nearest PIONEER authorized

service center or your dealer for a replacement.

S002*_A1_En

CAUTION

The STANDBY/ON switch on this unit will not

completely shut off all power from the AC outlet.

Since the power cord serves as the main disconnect

device for the unit, you will need to unplug it from the

AC outlet to shut down all power. Therefore, make

sure the unit has been installed so that the power

cord can be easily unplugged from the AC outlet in

case of an accident. To avoid fire hazard, the power

cord should also be unplugged from the AC outlet

when left unused for a long period of time (for

example, when on vacation).

D3-4-2-2-2a*_A1_En

X-CM52_LXE_En.book 2 ページ２０１４年３月２８日　金曜日　午前１０時３９分

Radio wave caution

T

his unit uses a 2.4 GHz radio wave frequency, which is

a band used by other wireless systems (Microwave

ovens and Cordless phones, etc.). In this event noise

appears in your television image, there is the possibility

this unit (including products supported by this unit) is

causing signal interference with the antenna input

connector of your television, video, satellite tuner, etc. In

this event, increase the distance between the antenna

input connector and this unit (including products

supported by this unit).

• Pioneer is not responsible for any malfunction of the

compatible Pioneer product due to communication

error/malfunctions associated with your network

connection and/or your connected equipment.

Please contact your Internet service provider or

network device manufacturer.

• A separate contract with/payment to an Internet

service provider is required to use the Internet.

WARNING

Store small parts out of the reach of children and

infants. If accidentally swallowed, contact a doctor

immediately.

These symbols are only valid

in the European Union.

K058c_A1_En

(Symbol examples for batteries)

Pb

X-CM52_LXE_En.book 3 ページ２０１４年３月２８日　金曜日　午前１０時３９分

4

En

Thank you for buying this Pioneer product.

Please read through these operating instructions so that you will know how to operate your model properly. After you

have finished reading the instructions, put them in a safe place for future reference.

Contents

01 Before you start

What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Loading the batteries in the remote control . . . . . . . . . . . . . . . . . 5

Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

02 Part names and functions

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Speaker system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Detatching and replacing the front grille . . . . . . . . . . . . . . . . . . . . 8

Attaching the Non-skid pads . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Rotating the Speaker Badge. . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Top panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

03 Connections

Speaker connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connecting using an HDMI cable . . . . . . . . . . . . . . . . . . . . . 13

Audio signals that can be output from this unit's

HDMI OUT terminal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connecting the FM antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Using external antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

04 Getting started

To turn the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Input function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Display brightness control . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Volume auto set-in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Volume control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Sound controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Equalizer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

P.bass control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Bass/treble control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Setting the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Calling the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Cancelling the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . . . 17

Using the wake-up timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Using the sleep timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Using Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

05 iPod/iPhone/iPad playback

Confirming what iPod/iPhone/iPad models are

supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Connecting your iPod/iPhone/iPad . . . . . . . . . . . . . . . . . . . . . . . 18

Connecting iPod/iPhone/iPad using supplied

stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Playing iPod/iPhone/iPad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

06 Disc playback

Playing discs or files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Advanced DVD, CD disc playback . . . . . . . . . . . . . . . . . . . . . . . .21

Direct track search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

A-B Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Repeat play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Programmed play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Search mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

About downloading MP3/WMA . . . . . . . . . . . . . . . . . . . . . . . 24

About playback order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Procedure to playback DivX or MP3/WMA/JPEG file . . . . . . 25

07 USB playback

Playing USB storage devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Procedure to playback DivX or MP3/WMA/JPEG file . . . . . . 26

Playing in the desired order (Programmed Play) . . . . . . . . . . . . 27

08 Using the tuner

Listening to the radio broadcasts . . . . . . . . . . . . . . . . . . . . . . . . 28

Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Saving station presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

To recall a memorised station. . . . . . . . . . . . . . . . . . . . . . . . . 29

To scan the preset stations . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

To erase entire preset memory . . . . . . . . . . . . . . . . . . . . . . . . 29

09 Other connections

Connecting auxiliary components . . . . . . . . . . . . . . . . . . . . . . . . 30

10

Bluetooth

®

Audio playback

Music playback using Bluetooth wireless technology . . . . . . . . 31

Remote control operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Pairing with the unit (Initial registration) . . . . . . . . . . . . . . . . . . 31

Listen to music on the unit from a Bluetooth capable

device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

BT STANDBY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Radio wave caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Scope of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Radio wave reflections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Precautions regarding connections to products

supported by this unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

11 Changing the settings

Settings for DVD/CD and USB playback . . . . . . . . . . . . . . . . . . 34

Audio Settings parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Video Adjust parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Initial Settings parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Setting the HDMI Resolution settings back to their

defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

12 Additional information

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Language Code Table and Country/Area Code Table . . . . . . . . 39

Language Code Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Country/Area Code Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Playable discs and formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Discs that cannot be played . . . . . . . . . . . . . . . . . . . . . . . . . . 40

About region numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Regarding copy protected CDs . . . . . . . . . . . . . . . . . . . . . . . . 40

About playing DualDiscs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Playing discs created on computers or BD/DVD

recorders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Playable files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Supported video file formats . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Displaying external subtitle files . . . . . . . . . . . . . . . . . . . . . . . 41

Supported image file formats . . . . . . . . . . . . . . . . . . . . . . . . . 41

Supported audio file formats. . . . . . . . . . . . . . . . . . . . . . . . . . 41

Cautions on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

When moving this unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Place of installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Do not place objects on this unit . . . . . . . . . . . . . . . . . . . . . . 42

About condensation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Cleaning the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Cleaning the lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Handling discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Storing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Cleaning discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

About specially shaped discs . . . . . . . . . . . . . . . . . . . . . . . . . 43

About iPod/iPhone/iPad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Auto power off setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Restoring all the settings to the defaults . . . . . . . . . . . . . . . . . . 43

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

X-CM52_LXE_En.book 4 ページ２０１４年３月２８日　金曜日　午前１０時３９分

Before you start 01

5

En

English

Chapter 1:

Before you start

What’s in the box

Please confirm that the following accessories are in the box

when you open it.

• Remote control

• AAA batteries (R03) x 2

•Power cord

• Speaker wire x 2

• Video cable (1.5 m)

• FM wire antenna

• Non-skid pads x 8

• iPhone/iPad stand

• Warranty card

• Operating instructions (this document)

Loading the batteries in the

remote control

1 Open the rear lid and load the batteries as

illustrated below.

2 Close the rear lid.

CAUTION

• Do not use any batteries other than the ones specified.

Also, do not use a new battery together with an old one.

• When inserting the batteries, make sure not to damage

the springs on the battery’s  terminals. This can cause

batteries to leak or over heat.

• When loading the batteries into the remote control, set

them in the proper direction, as indicated by the polarity

marks ( and ).

• Do not heat batteries, disassemble them, or throw them

into flames or water.

• Batteries may have different voltages, even if they are the

same size and shape. Do not use different types of

batteries together.

• To prevent leakage of battery fluid, remove the batteries

if you do not plan to use the remote control for a long

period of time (1 month or more). If the fluid should leak,

wipe it carefully off the inside of the case, then insert new

batteries. If a battery should leak and the fluid should get

on your skin, flush it off with large quantities of water.

• When disposing of used batteries, please comply with

governmental regulations or environmental public

institution’s rules that apply in your country/area.

WARNING

• Do not use or store batteries in direct sunlight or other

excessively hot place, such as inside a car or near a

heater. This can cause batteries to leak, overheat,

explode or catch fire. It can also reduce the life or

performance of batteries.

Using the remote control

The remote has a range of about 7 m at an angle of about 30º

from the remote sensor.

Keep in mind the following when using the remote control:

• Make sure that there are no obstacles between the

remote and the remote sensor on the unit.

• Remote operation may become unreliable if strong

sunlight or fluorescent light is shining on the unit’s

remote sensor.

• Remote controllers for different devices can interfere

with each other. Avoid using remotes for other

equipment located close to this unit.

• Replace the batteries when you notice a fall off in the

operating range of the remote.

O

P

T

ION

AS

P

MP

T

YD

I

S

P

L

A

Y

RD

S

STANDBY/O

N





D

V

D

/CD

USB

AU

D

IO

I

N/

L

INE

TU

N

ER

T

OP

ME

NU

MENU/

P

B

C

HO

M

E

/MENU

P

R

ES

E

T

VOLUME

SHIFT

+

M

U

T

E

TUN

E

–

TUNE+

DIM

M

ER















–

+

–

R

E

TURN

123

456

789

0

BT

A

U

DIO

CL

OCK/T

IMER

SLEEP

EQUAL

I

Z

E

R

AUDI

O SUBTITLE ANGLE

P.

BAS

S

ZOO

MMEMOR

Y

PROGRAM

BAS

S/TREBLE

ST/MO

NO V

ID

E

O MO

D

E

A-

B

DISPLAY

CLEAR

RPT/RDM

OPEN

/

CLOSE

ENTE

R

30°

7 m

30°

X-CM52_LXE_En.book 5 ページ２０１４年３月２８日　金曜日　午前１０時３９分

Part names and functions02

6

En

Chapter 2:

Part names and functions

Remote control

1  STANDBY/ON

Switches the receiver between standby and on (page 20).

2 Input function buttons

Use to select the input source to this receiver (page 20).

BT AUDIO

Use to set up or play the audio file using the Bluetooth

network (page 31).

3 Numeric buttons (0 to 9)

Use to enter the number (page 21).

AUDIO*

For discs or files including multiple audio streams/

channels, the audio stream/channel can be switched

during playback. For files stored in iPod/iPhone/iPad,

this button is not available.

SUBTITLE*

On DVD-Video or DivX discs containing subtitles in

multiple languages, the subtitle can be switched during

playback. For files stored in iPod/iPhone/iPad, this

button is not available.

ANGLE*

On DVD-Video discs containing multiple angles, the

angle can be switched during playback.

ZOOM*

Zooming on the image. For images stored in iPod/

iPhone/iPad, this button is not available.

MEMORY*

Use to memory the radio station (page 28).

PROGRAM*

Use to program the DVD-Video, MP3/WMA disc or USB

mass storage device (page 23).

ST/MONO*

Use to switch the sound mode between stereo and

monaural (page 28).

VIDEO MODE*

Use to change the output resolution (HDMI only)

(page 35).

A-B*

The specified section within a single title or track is

played repeatedly.

4

CLEAR

Press to clear the selected item.

Use this for example if you use to clear the programmed play

(page 23).

OPTION

ASPM PTY DISPLAY

RDS

3

4

1

2

5

6

7

11

12

17

13

14

15

8

9

10

16

STANDBY/ON





DVD/CD USB

AUDIO IN/LINE

TUNER

TOP MENU MENU/PBC

HOME/MENU

PRESET VOLUME

SHIFT

+

MUTE

TUNE–

TUNE+

DIMMER

 







–

+

–

RETURN

123

456

789

0

BT AUDIO

CLOCK/TIMER

SLEEP

EQUALIZER

AUDIO SUBTITLE ANGLE

P. BA SS

ZOOM MEMORY PROGRAM

BASS/TREBLE

ST/MONO VIDEO MODE A-B

DISPLAY

CLEAR RPT/RDM

OPEN/CLOSE

ENTER

X-CM52_LXE_En.book 6 ページ２０１４年３月２８日　金曜日　午前１０時３９分

Part names and functions 02

7

En

English

5 DVD Receiver control buttons

TOP MENU

Press to display the top menu of the DVD-Video.

MENU/PBC

Use to access the DVD menu or VCD PBC menu.

HOME/MENU

Press to display the menu screen.

Use this to change initial settings of the unit (page 34).

• Audio Settings (page 34)

• Video Adjust (page 34)

• Play Mode

The Play Mode function may not work for some discs or

files. For files stored on iPod/iPhone/iPad, this function

is not available.

A-B Repeat (page 21)

The specified section within a single title or track is

played repeatedly.

Repeat (page 22)

Plays titles, chapters, tracks or files repeatedly.

Random (page 22)

Plays titles, chapters or tracks in random order.

Program (page 23)

Plays titles, chapters, tracks or files in the order in which

you program them.

Search Mode (page 24)

Plays the specified number or time within the title,

chapter, track or file.

• Disc Navigator

Select and plays title, chapter, track or file from the Disc

Navigator.

Ex.: DVD-Video Disc Navigator

• Initial Settings (page 34)

RETURN

Press to return to the previous screen. Also, use to

cancel the clock setting or the sound setting.

6

///

(TUNE +/–), ENTER

Use to select/switch system settings and modes, and to

confirm actions.

Use

TUNE +/– can be used to find radio frequencies

(page 28).

7

PRESET +/–

Use to select preset radio stations (page 28).

8

MUTE

Mutes/unmutes the sound (page 15).

9 Playback control buttons

Use to control each function after you have selected it using

the input function buttons (page 20).



Press to start playback.



Press to stop playback.

///

• Press to return to the beginning of the currently playing

track or file. Press twice to move back to the beginning

of the previous track or file.

• Press and hold during playback to fast-reverse.

• Press in the pause mode to move backward frame-by-

frame. (DVD-Video only)

• Press and hold in the pause mode for slow play in the

reverse direction. (DVD-Video only)

///

• Press during playback to skip ahead to the beginning of

the next track or file.

• Press and hold during playback to fast-forward.

• Press in the pause mode to move forward frame-by-

frame. (DVD-Video, Video CD or DivX files only)

• Press and hold in the pause mode for slow play in the

forward direction. (DVD-Video, Video CD or DivX files

only)

Audio Settings

Play Mode

Disc Navigator

Initial Settings

Video Adjust

HOME MENU

DVD

Move Select

ENTER

Exit

HOME MENU

A-B Repeat

Repeat

Random

Program

Search Mode

A(Start Point)

B(End Point)

Off

Play Mode

Setup playback functions such as Program. Random and

Repeat play

01

04

02 03

Disc Navigator: Title

01- 49: – –

Move

Select

ENTER

Prev. Next



05 06

X-CM52_LXE_En.book 7 ページ２０１４年３月２８日　金曜日　午前１０時３９分

Part names and functions02

8

En

10

SHIFT

Press to access the ‘blue’ commands (above the

buttons) on the remote. These buttons are marked with

an asterisk (*) in this section.

11 OPEN/CLOSE

Use to open or close the disc tray (page 20).

12 DVD Receiver control buttons

CLOCK/TIMER

Use for setting the clock, as well as for setting and

checking the timers (page 15).

SLEEP

See Using the sleep timer on page 17.

13 Sound control buttons

Adjust the sound quality (page 16).

14

DISPLAY

Press to change the display for DVD-Video, Video CD, CD or

MP3.

Ex.: DVD-Video DISPLAY

15

RPT

/

RDM

Press to change the repeat play or randomize order play

setting from a DVD-Video, Video CD, CD or iPod (page 21).

16 Volume

control buttons

Use to set the listening volume (page 15).

17

DIMMER

Dims or brightens the display. The brightness can be

controlled in four steps (page 15).

Note

• This unit does not use the OPTION buttons.

• This unit does not use the RDS buttons.

Speaker system

1 Tweeter

2 Woofer

3 Bass Reflex Duct

4 Speaker Terminals

Important

• Speaker grille can be removed.

• Make sure nothing comes into contact with the speaker

diaphragms when you remove the speaker grilles.

• Both speakers can be used on either the right or the left

side.

Detatching and replacing the front

grille

The front grille of this speaker system is removable. Proceed

as follows:

1 Grab the bottom of the grille, and gently

pull it toward you to remove the bottom

portion.

2 Next, grab the top part of the grille and

gently pull it toward you to remove the top

portion.

To install the grille, align the projections on the speaker with

the receptacles on the top and at the base of the grille and

push them into place.

Play

Playback status

Time display

Subtitle Language

Audio Language

Audio format

DVD-Video

Current / Total

1 Chinese - - 1

Audio Dolby Digital 2 / 0 CH Subtitle Angle

1/4Title

Elapsed Remain Total

5:34 35:56 41:30



Play



PAUSE



Slow Backward



Slow Forward



Fast Backward



Fast Forward



3

2

1

4

X-CM52_LXE_En.book 8 ページ２０１４年３月２８日　金曜日　午前１０時３９分

Part names and functions 02

9

En

English

Attaching the Non-skid pads

Apply the accessory non-skid pads to the bottom surfaces of

the speakers.

Important

• Use the speaker is usually in an upright position.

When placing speakers upright

When placing the speakers vertically upright, attach the non-

skid pads to the bottom surface of the speakers.

When placing speakers horizontally

When placing the speaker horizontally, attach the non-skid

pads to what will be the bottom surface of the speakers.

Rotating the Speaker Badge

The grill frame speaker badge can be rotated. Operate as

follows.

1 Grasp the speaker badge (1), pull forward

(2), and turn left (3).

The speaker badge will rotate.

If the speaker badge does not rotate doing the above step 1,

try the following steps 2 to 3.

2 Detach the speaker grill.

3 Rotate the screws on the backside of the grill

in a clockwise direction using a plus driver.

Important

• Do not rotate the screw in a counter-clockwise direction

as it may cause the badge to fall off.

The bottom surface

of the speaker

The bottom surface of

the speaker when

using it horizontally

1

2

3

Backside of speaker grill

X-CM52_LXE_En.book 9 ページ２０１４年３月２８日　金曜日　午前１０時３９分

Part names and functions02

10

En

Front panel

1Main display

2 Volume control

Use to set the listening volume (page 15).

3

Volume

illumination

Light when the power on.

4 Headphone socket

Use to connect headphones. When the headphones are

connected, there is no sound output from the speakers.

5 AUDIO IN socket

Use to connect an auxiliary component using a stereo

minijack cable (page 30).

6 Remote sensor

Receives the signals from the remote control.

7 Disc tray

Place the disc, label side up (page 20).

8

TIMER

indicator

Lights when the receiver is power off with timer setting.

9 USB terminal

Use to connect your USB mass storage device or Apple iPod/

iPhone/iPad as an audio source (page 26).

TIMER VOLUME

PHONES AUDIO IN

4 5 6 7 8 9

2 31

X-CM52_LXE_En.book 10 ページ２０１４年３月２８日　金曜日　午前１０時３９分

Part names and functions 02

11

En

English

Top panel

1  STANDBY/ON

Switches the receiver between standby and on (page 20).

2 Playback control buttons

Selects the desired track or file to be played back. Use to stop

the playback. Stops playback or resumes playback from the

pause point.

3 INPUT

Selects the input source.

Long press to change to BT STANDBY mode.

4 Disc tray open/close button

Use to open or close the disc tray (page 20).

STANDBY/ON







 

INPUT



1 4

1

2 3

X-CM52_LXE_En.book 11 ページ２０１４年３月２８日　金曜日　午前１０時３９分

Connections03

12

En

Chapter 3:

Connections

CAUTION

• Be sure to turn off the power and unplug the power cord

from the power outlet whenever making or changing

connections.

• Connect the power cord after all the connections

between devices have been completed.

Speaker connection

• Push open the tabs and insert exposed wire.

• The provided speaker wire with red tube is for the (+)

terminal. Connect the wire with red tube the (+)

terminal, and other wire to the (–) terminal.

• Both speakers can be used on either the right or the left

side.

CAUTION

• These speaker terminals carry HAZARDOUS LIVE

voltage. To prevent the risk of electric shock when

connecting or disconnecting the speaker cables,

disconnect the power cord before touching any

uninsulated parts.

• Do not connect any speakers other than those supplied

to this system.

• Do not connect the supplied speakers to any amplifier

other than the one supplied with this system.

Connection to any other amplifier may result in

malfunction or fire.

• Do not attach these speakers to the wall or ceiling. They

may fall off and cause injury.

• These speakers are magnetically shielded. However,

depending on the installation location, color distortion

may occur if the speaker system is installed extremely

close to the screen of a television set. If this happens,

turn off the television set, and then turn it on after 15 to

30 minutes. If the problem persists, move the speaker

system away from the television set.

• Make sure that the speaker cable cores do not become

exposed and make contact with other cable cores. This

may cause malfunction of the product.

• Do not allow the speaker cable core to come into contact

with the receiver body.

• If the speaker cable core comes into contact with any

metal portion of the receiver’s body, it may damage the

speakers and cause smoke and fire.

Insert speaker cables securely into the terminals and

check that the cable does not come out of easily.

Note

• There is no difference between L and R speakers.

SPEAKERS

R

L

ANTENNA

VIDEO

OUT

COMPONENT

VIDEO

OUT

IN

LINE

P

B

P

R

Y

L

R

FM

UNBAL 75 Ω

HDMI

AC IN

1

2

Left

speaker

Right

speaker

This unit’s rear panel

Red tube

Supplied

speaker wire

X-CM52_LXE_En.book 12 ページ２０１４年３月２８日　金曜日　午前１０時３９分

Connections 03

13

En

English

Connecting using an HDMI cable

By using an HDMI cable, digital signals can be transferred to

an HDMI-compatible TV on a single cable with no loss of

picture or sound quality. After connecting, make this unit's

resolution and HDMI color settings according to the HDMI-

compatible TV. Also refer to the operating instructions with

the HDMI-compatible TV.

Note

• When playing a disc or USB storage device content, this

unit can transfer digital signals by the HDMI OUT

terminal. Use the video cable for playing other content.

• This unit’s interface is designed based on the High-

Definition Multimedia Interface specification.

• When an HDMI-compatible device is connected, the

resolution is displayed on the front panel display.

• The resolution of the video signals output from this unit’s

HDMI OUT terminal is changed manually. Change the

HDMI Resolution setting (page 35).

• This unit is designed for connection to HDMI-compatible

devices. It may not operate properly if connected to DVI

devices.

The term HDMI and High-Definition Multimedia Interface,

and the HDMI Logo are trademarks or registered trademarks

of HDMI Licensing, LLC in the United States and other

countries.

AC IN

R

L

ANTENNA

VIDEO

OUT

COMPONENT

VIDEO

OUT

IN

LINE

PB

PR

Y

SPEAKERS

L

R

FM

UNBAL 75 Ω

HDMI

AC IN

R

L

Yellow

TV

Video cable

(supplied)

To video input

terminal

This unit’s rear panel

Component video cable

(commercially available)

ANTENNA

OUT

COMPONENT

VIDEO

OUT

IN

LINE

P

B

P

R

FM

UNBAL 75 Ω

HDMI

Match the direction of

the plug to the

terminal and insert

straight.

To HDMI input

terminal

HDMI cable

(commercially

available)

TV

This unit’s rear panel

X-CM52_LXE_En.book 13 ページ２０１４年３月２８日　金曜日　午前１０時３９分

Connections03

14

En

Audio signals that can be output from

this unit's HDMI OUT terminal

• 44.1 kHz to 96 kHz, 16-bit/ 20-bit/ 24-bit 2-channel linear

PCM audio (including 2-channel downmixing)

• Dolby Digital 5.1-channel audio

•MPEG audio

• Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of

Dolby Laboratories.

Connecting the FM antenna

Connect the FM antenna plug onto the center pin of the FM

antenna socket.

Note

• To ensure optimum reception, make sure the FM

antenna is fully extended and not coiled or hanging at

the rear of the unit.

Using external antennas

To improve FM reception

Use a PAL connector (not supplied) to connect an exte rnal FM

antenna.

Plugging in

Before making or changing the connections, switch off the

power and disconnect the power cord from the AC outlet.

After you’ve finished making all connections, plug the unit

into an AC outlet.

CAUTION

• Do not use any power cord other than the one supplied

with this unit.

• Do not use the supplied power cord for any purpose

other than that described above

ANTENNA

OUT

COMPONENT

VIDEO

OUT

P

B

P

R

Y

FM

UNBAL 75 Ω

HDMI

This unit’s rear panel

FM wire antenna

(supplied)

ANTENNA

FM

UNBAL 75 Ω

One-touch

PAL connector

75 coaxial cable

VIDEO

OUT

COMPONENT

VIDEO

OUT

IN

LINE

P

B

P

R

Y

SPEAKERS

L

R

AC IN

R

L

To AC outlet

This unit’s rear panel

Power cord

X-CM52_LXE_En.book 14 ページ２０１４年３月２８日　金曜日　午前１０時３９分

Getting started 04

15

En

English

Chapter 4:

Getting started

To turn the power on

Press the  STANDBY/ON to turn the power on.

After use:

Press the  STANDBY/ON to enter the power stand-by

mode.

Note

• In standby mode, if iPod/iPhone/iPad is connected, the

unit turns charge mode.

Setting the clock

1 Press

 STANDBY/ON

to turn the power on.

2 Press

CLOCK/TIMER

on the remote control.

“CLOCK” is shown on the main display.

3 Press

ENTER

.

4 Press

/

to set the day, then press ENTER.

5 Press

/

to set the hour, then press

ENTER.

6Press

/

to set the minute, then press

ENTER to confirm.

To confirm the time display:

Press the CLOCK/TIMER. The time display will appear for

about 10 seconds.

To readjust the clock:

Perform “Setting the clock” from step 1.

Note

• When power supply is restored after unit is plugged in

again or after a power failure, reset the clock.

General control

Input function

When the INPUT on main unit is pressed, the current function

will change to different mode. Press the

INPUT repeatedly to

select desired function.

Display brightness control

Press DIMMER to dims the display brightness. The brightness

can be controlled in four steps.

Volume auto set-in

If you turn off and on the main unit with the volume set to 31

or higher, the volume starts at 30 and sets in to the last set

level.

Volume control

Turn the volume knob towards VOLUME (on main unit) or

press

VOLUME +/– (on remote control) to increase or

decrease the volume.

CAUTION

• The sound level at a given volume setting depends on

speaker efficiency, location, and various other factors. It

is advisable to avoid exposure to high volume levels. Do

not turn the volume on to full at switch on. Listen to

music at moderate levels. Excessive sound pressure

from earphones and headphones can cause hearing

loss.

Muting

The volume is muted temporarily when pressing the MUTE on

the remote control. Press again to restore the volume.

STANDBY/ON





123

DVD/CD USB

AUDIO IN/LINE

TUNER

BT AUDIO

CLOCK/TIMER

SLEEP

EQUALIZER

AUDIO SUBTITLE ANGLE

OPEN/CLOSE

TOP MENU MENU/PBC

HOME/MENU

TUNE+

RETURN

ENTER

DVD/CD FM USB/IPOD

BT AUDIO AUDIO IN LINE

X-CM52_LXE_En.book 15 ページ２０１４年３月２８日　金曜日　午前１０時３９分

Getting started04

16

En

Sound controls

Equalizer

When the EQUALIZER is pressed, the current mode setting

will be displayed. To change to a different mode, press the

EQUALIZER repeatedly until the desired sound mode appears.

P.bass control

When the power is first turned on, the unit will enter the

P.bass mode which emphasises the bass frequencies. To

cancel the P.bass mode, press the

P.BASS on the remote

control.

Bass/treble control

Press the BASS/TREBLE, then press /// to adjust the

bass or treble.

Note

•The

EQUALIZER and P.BASS cannot operate

simultaneously. The most recently selected of these two

functions will be the one used.

•

BASS/TREBLE can operate alongside either the

EQUALIZER or P.BASS.

When one of the above two functions is

selected, the function that is not selected will

be displayed as follows.

1 When P.BASS setting (ON/OFF) is changed

• EQUALIZER : FLAT

2 When EQUALIZER setting is changed

• P.BASS : OFF

Setting the wake-up timer

Used to change the existing timer setting, or to set a new

timer.

1Press

 STANDBY/ON

to turn the power on.

2 Press and hold

CLOCK/TIMER

.

3Press

/

to select “ONCE“ or “DAILY“,

then press

ENTER

.

ONCE – Once timer play works for one time only at a

preset time.

DAILY – Daily timer play works at the same preset time

and days of week.

4Press

/

to select “

TIMER

SET“, then

press

ENTER

.

5Press

/

to select the timer playback

source, then press

ENTER

.

DVD/CD, FM, USB/IPOD, BT AUDIO, AUDIO IN and LINE can be

selected as the playback source.

6Press

/

to select the timer day, then

press

ENTER

.

7Press

/

to set the hour, then press

ENTER

.

8Press

/

to set the minute, then press

ENTER

.

Set the time to finish as in steps 7 and 8 above.

9 Adjust the volume press

VOLUME +/–

, then

press

ENTER

.

10 Press

 STANDBY/ON

to enter the power

standby mode.

The TIMER indicator lights up.

NIGHT

FLAT A flat and basic sound

ACTIVE

DIALOGUE

A sound that can be enjoyed

at night even with lower volume

A powerful sound that

emphasizes low and high tones

A sound that allows the radio or

vocals to be heard more easily

X-CM52_LXE_En.book 16 ページ２０１４年３月２８日　金曜日　午前１０時３９分

Getting started 04

17

En

English

Calling the wake-up timer

It can be used to re-use an existing timer setting.

1 As well as steps 1 through 3 in “Setting the

wake-up timer”.

2 Press

/

to select “

TIMER

ON

“, then

press

ENTER

.

Cancelling the wake-up timer

It can be used to turn off the timer setting.

1 As well as steps 1 through 3 in “Setting the

wake-up timer”.

2 Press

/

to select “

TIMER

OFF

“, then

press

ENTER

.

Using the wake-up timer

1 Press

 STANDBY/ON

to turn the power

off.

2 At the wake-up time, this unit will turn on

automatically and play the selected input

function.

Note

• If at the wake-up time iPod/iPhone/iPad is not connected

to this unit or a disc is not inserted, this unit will be

turned to on and not play back the track.

• Some discs may not be played automatically at the wake-

up time.

• If you set the timer, take one minute or more between the

start and end time.

Using the sleep timer

The sleep timer switches off the unit after a specified time so

you can fall asleep without worrying about it.

1 Press

SLEEP

repeatedly to select a switch off

time.

Choose between 10 min, 20 min, 30 min, 60 min, 90 min, 120

min, 150 min, 180 min or OFF. The newly set value displays for

5 seconds, and then the setting is completed.

Note

• The sleep timer can be set by pressing

SLEEP while the

remaining time is displayed.

Using Headphones

Connect to the jack plug of the headphones.

When the headphones are connected, there is no sound

output from the speakers.

• Do not turn the volume on to full at switch on and listen

to music at moderate levels. Excessive sound pressure

from earphones and headphones can cause hearing

loss.

• Before plugging in or unplugging the headphone,

reduce the volume.

• Be sure your headphone has a 3.5 mm diameter plug

and impedance between 16

 and 50 . The

recommended impedance is 32

.

TIMER VOLUME

PHONES AUDIO IN

X-CM52_LXE_En.book 17 ページ２０１４年３月２８日　金曜日　午前１０時３９分

iPod/iPhone/iPad playback05

18

En

Chapter 5:

iPod/iPhone/iPad playback

Merely by connecting your iPod/iPhone/iPad to this unit, you

can enjoy high-quality sound from your iPod/iPhone/iPad.

This unit can not transfer music, movies and images from an

iPod/iPhone/iPad via the

HDMI OUT and COMPONENT VIDEO

terminal. Playback setting for iPod/iPhone/iPad music and

images can be performed from this unit or the iPod/iPhone/

iPad itself.

Confirming what iPod/iPhone/iPad

models are supported

The iPod/iPhone/iPad playable on this unit are shown below.

Note

• Pioneer does not guarantee that this unit plays iPod/

iPhone/iPad models other than the ones specified.

• Some functions may be restricted depending on the

model or software version.

• iPod/iPhone/iPad is licensed for reproduction of non-

copyrighted materials or materials the user is legally

permitted to reproduce.

• Features such as the equalizer cannot be controlled

using this system, and we recommend switching the

equalizer off before connecting.

• Pioneer cannot under any circumstances accept

responsibility for any direct or indirect loss arising from

any inconvenience or loss of recorded material resulting

from iPod/iPhone/iPad failure.

• For detailed instructions on using the iPod/iPhone/iPad,

please refer to the manual supplied with the iPod/

iPhone/iPad.

• This system has been developed and tested for the

software version of iPod/iPhone/iPad indicated on the

website of Pioneer (http://pioneer.jp/homeav/support/

ios/ao/).

• Installing software versions other than indicated on the

website of Pioneer to your iPod/iPhone/iPad may result

in incompatibility with this system.

• This unit cannot be used to record CD, tuner or other

content on an iPod/iPhone/iPad.

Connecting your iPod/iPhone/iPad

CAUTION

• When connecting iPod/iPhone/iPad devices, use the

iPod/iPhone/iPad cable provided with iPod/iPhone/iPad

devices, or a commercially available iPod/iPhone/iPad

cable designed to support iPod/iPhone/iPad.

• An iPod/iPhone/iPad cable is not supplied with this unit.

Important

• If you are mounting the protective cover of a

commercially available iPod/iPhone/iPad, you may not

be able to connect iPod/iPhone/iPad to this unit.

Connecting iPod/iPhone/iPad using

supplied stand

1 Connect the unit to an iPod/iPhone/iPad

with the iPod/iPhone/iPad cable.

iPod/iPhone/iPad USB Terminal

iPod nano 3G/4G/5G/6G/7G 

iPod touch 1G/2G/3G/4G/5G 

iPhone 

iPhone 3G 

iPhone 3GS 

iPhone 4 

iPhone 4s 

iPhone 5 

iPhone 5c 

iPhone 5s 

iPad mini 

iPad mini with Retina display 

iPad 

iPad 2 

iPad (3rd generation) 

iPad (4th generation) 

iPad Air 

iPod/iPhone/iPad

cable

X-CM52_LXE_En.book 18 ページ２０１４年３月２８日　金曜日　午前１０時３９分

iPod/iPhone/iPad playback 05

19

En

English

2 Set up to stand the iPod/iPhone/iPad.

When using an iPod/iPhone

Make sure the iPod/iPhone cable is aligned along the groove

for it on the back of the stand that comes with the unit.

When using iPad

Make sure to place the iPad in a horizontal direction on the

stand.

Playing iPod/iPhone/iPad

1 Connect your iPod/iPhone/iPad.

If an iPod/iPhone/iPad is connected when this unit is on,

playback of the iPod/iPhone/iPad will not begin.

2 Press USB as the input source.

“USB/IPOD” is shown on the main display.

3 When the recognition is completed, will

begin playing automatically.

The available iPod/iPhone/iPad playback control by this unit

is ,  ,  .

CAUTION

• When your iPod/iPhone/iPad is placed on the stand and

you wish to operate the iPod/iPhone/iPad directly, be

sure to steady the iPod/iPhone/iPad with the other hand

to prevent malfunctions due to faulty contacts.

Note

• For detailed instructions on using the iPod/iPhone/iPad,

please refer to the manual supplied with the iPod/

iPhone/iPad.

• iPod/iPhone/iPad recharging occurs whenever an iPod/

iPhone/iPad is connected to this unit. (This function is

supported in standby mode as well.)

• When input is switched from USB/IPOD to another

function, iPod/iPhone/iPad playback is temporarily

stopped.

• When iPod/iPhone/iPad is not playing and no operations

have been performed for more than 20 minutes, the unit

will automatically power off. In this case it is required

that the Auto power off is switched to

ON.

• Auto power off can be switched to

ON/OFF (page 43).

Important

• If this unit cannot play your iPod/iPhone/iPad, perform

the following troubleshooting checks:

-

Check whether the iPod/iPhone/iPad is supported by this

unit.

- Reconnect the iPod/iPhone/iPad to the unit. If this

doesn’t seem to work, try resetting your iPod/iPhone/

iPad.

- Check the iPod/iPhone/iPad software is supported by this

unit.

• If the iPod/iPhone/iPad cannot be operated, check the

following items:

- Is the iPod/iPhone/iPad connected correctly? Reconnect

the iPod/iPhone/iPad to the unit.

- Is the iPod/iPhone/iPad experiencing a hangup? Try

resetting the iPod/iPhone/iPad, and reconnect it to the

unit.

Back of stand

iPod/iPhone

cable

X-CM52_LXE_En.book 19 ページ２０１４年３月２８日　金曜日　午前１０時３９分

Disc playback06

20

En

Chapter 6:

Disc playback

Playing discs or files

1 Press

 STANDBY/ON

to turn the power on.

The selected input is displayed on the front panel display.

• When playing discs or files, turn the TV on and switch TV

input before starting.

• You can change the screen display language of the unit

(Display settings on page 35).

2 Press

DVD

/

CD

on the remote control or

INPUT

repeatedly on the main unit to select

DVD

/

CD

input.

Please wait until you see the “NO DISC“.

When a disc is already on the disc tray, press

 OPEN/

CLOSE

to eject the disc.

3 Press

 OPEN/CLOSE

to open the disc tray.

4 Place the disc on the disc tray, label side up.

5 Press

 OPEN/CLOSE

to close the disc tray.

6 Press



to start playback.

CAUTION

• Do not place two discs in one disc tray.

• Do not play discs of special shapes (heart, octagon, etc).

It may cause malfunctions.

• Do not push the disc tray whilst it is moving.

• If the power fails whilst the tray is open, wait until the

power is restored.

• Be sure to place 8 cm disc in the middle of the disc tray.

Note

• Due to the structure of the disc information, it takes longer

to read the disc has written by many files than a normal CD

(approximately 20 to 90 seconds).

• When the beginning of the first track is reached during fast

reverse, the unit will enter the playback mode.

• Rewritable multi-session discs with unfinished writing, can

still be played.

• If TV or radio interference occurs during DVD/CD

operation, move the unit away from the TV or radio.

Tip

• When no operation has done in DVD/CD mode and the

audio file is not played for more than 20 minutes, the

power will automatically turn off. In this case it is

required that the Auto power off is switched to ON.

• Auto power off can be switched to On/OFF (page 43)

X-CM52_LXE_En.book 20 ページ２０１４年３月２８日　金曜日　午前１０時３９分

ページが読み込まれています...

Pioneer X-CM52BT 取扱説明書

Pioneer X-CM52BT 取扱説明書

他の言語で

関連論文

その他のドキュメント