Pioneer XV-DV373 Operating Instructions Manual

Operating Instructions

HTZ373_777_EN.book Page 1 Wednesday, March 5, 2008 1:08 PM

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

"dangerous voltage" within the product's

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_En-A

WARNING

This equipment is not waterproof. To prevent a fire

or shock hazard, do not place any container filled

with liquid near this equipment (such as a vase or

flower pot) or expose it to dripping, splashing, rain

or moisture.

D3-4-2-1-3_B_En

WARNING

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230 V

or 120 V) written on the rear panel.

D3-4-2-1-4_A_En

Before plugging in for the first time, read the following

section carefully.

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat

radiation (at least 10 cm at top, 10 cm at rear, and

10 cm at each side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the

product, and to protect it from overheating. To

prevent fire hazard, the openings should never be

blocked or covered with items (such as newspapers,

table-cloths, curtains) or by operating the

equipment on thick carpet or a bed.

D3-4-2-1-7b_A_En

Operating Environment

Operating environment temperature and humidity:

+5 ºC to +35 ºC (+41 ºF to +95 ºF); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c_A_En

WARNING

To prevent a fire hazard, do not place any naked

flame sources (such as a lighted candle) on the

equipment.

D3-4-2-1-7a_A_En

HTZ373_777_EN.book Page 2 Wednesday, March 5, 2008 1:08 PM

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the

plug by tugging the cord and never touch the power

cord when your hands are wet as this could cause a

short circuit or electric shock. Do not place the unit, a

piece of furniture, etc., on the power cord, or pinch the

cord. Never make a knot in the cord or tie it with other

cords. The power cords should be routed such that they

are not likely to be stepped on. A damaged power cord

can cause a fire or give you an electrical shock. Check

the power cord once in a while. When you find it

damaged, ask your nearest PIONEER authorized

service center or your dealer for a replacement.

S002_En

This product is for general household purposes. Any

failure due to use for other than household purposes

(such as long-term use for business purposes in a

restaurant or use in a car or ship) and which

requires repair will be charged for even during the

warranty period.

K041_En

CAUTION

The STANDBY/ON switch on this unit will not

completely shut off all power from the AC outlet.

Since the power cord serves as the main disconnect

device for the unit, you will need to unplug it from

the AC outlet to shut down all power. Therefore,

make sure the unit has been installed so that the

power cord can be easily unplugged from the AC

outlet in case of an accident. To avoid fire hazard,

the power cord should also be unplugged from the

AC outlet when left unused for a long period of time

(for example, when on vacation).

D3-4-2-2-2a_A_En

If the AC plug of this unit does not match the AC

outlet you want to use, the plug must be removed

and appropriate one fitted. Replacement and

mounting of an AC plug on the power supply cord of

this unit should be performed only by qualified

service personnel. If connected to an AC outlet, the

cut-off plug can cause severe electrical shock. Make

sure it is properly disposed of after removal.

The equipment should be disconnected by removing

the mains plug from the wall socket when left

unused for a long period of time (for example, when

on vacation).

D3-4-2-2-1a_A_En

CAUTION

This product is a class 1 laser product, but this product

contains a laser diode higher than Class 1.

To ensure continued safety, do not remove any covers or

attempt to gain access to the inside of the product.

Refer all servicing to qualified personnel.

The following caution label appears on your unit.

Location: top of the unit

CLASS 1

LASER PRODUCT

D3-4-2-1-8_B_En

cover & anki.fm 3 ページ２００８年３月１２日　水曜日　午後６時１６分

4

En

Thank you for buying this Pioneer product.

Please read through these operating instructions so that you will know how to operate your model

properly. After you have finished reading the instructions,

put them in a safe place for future referenc

e.

Contents

01 Controls and displays

Front panel . . . . . . . . . . . . . . . . . . . . . . . . .6

Remote control . . . . . . . . . . . . . . . . . . . . . .7

Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

02 Getting started

Home theater sound setup . . . . . . . . . . . .10

Using the Auto MCACC setup for optimal

surround sound . . . . . . . . . . . . . . . . . . . . .11

Using the on-screen displays. . . . . . . . . . .12

Playing discs . . . . . . . . . . . . . . . . . . . . . . .12

Basic playback controls . . . . . . . . . . . . .12

Resume and Last Memory. . . . . . . . . . . .13

DVD-Video disc menus . . . . . . . . . . . . . .13

Video CD/Super VCD PBC menus . . . . . .13

Listening to the radio. . . . . . . . . . . . . . . . .14

Improving poor FM reception . . . . . . . . .14

Memorizing stations . . . . . . . . . . . . . . . .14

Listening to station presets . . . . . . . . . . .14

Listening to other sources . . . . . . . . . . . . .14

03 Listening to your system

Auto listening mode . . . . . . . . . . . . . . . . .15

Listening in surround sound . . . . . . . . . . .15

Dolby Pro Logic II Music settings . . . . . .15

Using Front Stage Surround Advance . . . .16

Using Advanced Surround. . . . . . . . . . . . .16

Listening in stereo . . . . . . . . . . . . . . . . . . .16

Listening with headphones . . . . . . . . . . . .16

Listening with Acoustic Calibration EQ . . .17

Using the Sound Retriever. . . . . . . . . . . . .17

Enhancing dialogue. . . . . . . . . . . . . . . . . .17

Using the Tone controls. . . . . . . . . . . . . . .17

Adjusting the bass and treble . . . . . . . . .17

Quiet and Midnight modes . . . . . . . . . . .17

Boosting the bass level . . . . . . . . . . . . . . .17

04 Disc playback features

Scanning discs . . . . . . . . . . . . . . . . . . . . . 18

Playing in slow motion . . . . . . . . . . . . . . . 18

Frame advance/frame reverse . . . . . . . . . . 18

Playing a JPEG slideshow . . . . . . . . . . . . . 18

Browsing DVD or Video CD/Super VCD

discs with the Disc Navigator . . . . . . . . . . 19

Browsing Windows Media

TM

Audio (WMA),

MP3, MPEG-4 AAC, DivX video/WMV and

JPEG files with the Disc Navigator . . . . . . 20

Using Playlists . . . . . . . . . . . . . . . . . . . . . 20

Programming playlists . . . . . . . . . . . . . . 20

Listening to playlists . . . . . . . . . . . . . . . . 21

Clearing files from a playlist . . . . . . . . . . 21

Looping a section of a disc . . . . . . . . . . . . 21

Using repeat play . . . . . . . . . . . . . . . . . . . 21

Using random play . . . . . . . . . . . . . . . . . . 21

Creating a program list . . . . . . . . . . . . . . . 22

Other functions available from the

program menu . . . . . . . . . . . . . . . . . . . . 22

Searching a disc . . . . . . . . . . . . . . . . . . . . 23

Switching subtitles . . . . . . . . . . . . . . . . . . 23

Switching language/audio channels . . . . . 23

Zooming the screen . . . . . . . . . . . . . . . . . 23

Switching camera angles . . . . . . . . . . . . . 24

Displaying disc information. . . . . . . . . . . . 24

05 USB playback

Using the USB interface . . . . . . . . . . . . . . 25

Basic playback controls . . . . . . . . . . . . . . 25

Scanning files . . . . . . . . . . . . . . . . . . . . . . 26

Playing a JPEG slideshow . . . . . . . . . . . . . 26

Browsing files with the Navigator . . . . . . . 26

HTZ373_777_EN.book Page 4 Wednesday, March 5, 2008 1:08 PM

5

En

English

FrançaisDeutsch

Nederlands

Italiano Español

06 Surround sound settings

Using the Setup menu . . . . . . . . . . . . . . . 27

07 Video Adjust menu

Video Adjust menu. . . . . . . . . . . . . . . . . . 28

08 Initial Settings menu

Using the Initial Settings menu . . . . . . . . 29

Video Output settings. . . . . . . . . . . . . . . . 29

Language settings . . . . . . . . . . . . . . . . . . 30

Display settings . . . . . . . . . . . . . . . . . . . . 30

Options settings. . . . . . . . . . . . . . . . . . . . 31

Parental Lock. . . . . . . . . . . . . . . . . . . . . 31

About DivX

®

VOD content . . . . . . . . . . . 32

09 Other connections

Connecting external antennas . . . . . . . . . 33

Connecting auxiliary components . . . . . . 33

Connecting for digital audio. . . . . . . . . . 33

Connecting an analog audio

component . . . . . . . . . . . . . . . . . . . . . . 33

Connecting using the component video

output . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

About progressive scan video . . . . . . . . 34

Connecting using HDMI . . . . . . . . . . . . . 34

Switching the HDMI audio setting. . . . . 35

Resetting the HDMI connection. . . . . . . 35

About HDMI. . . . . . . . . . . . . . . . . . . . . . . 35

Using this unit with a Pioneer Flat

Screen TV. . . . . . . . . . . . . . . . . . . . . . . . . 35

SR+ Setup for Pioneer Flat Screen

TVs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Switching on the SR+ mode . . . . . . . . . 36

10 Additional information

Optional system settings . . . . . . . . . . . . . .37

Setting the sleep timer . . . . . . . . . . . . . . .38

Dimming the display . . . . . . . . . . . . . . . . .38

Disc/content format playback

compatibility . . . . . . . . . . . . . . . . . . . . . . .38

Disc compatibility table. . . . . . . . . . . . . .39

About DVD+R/DVD+RW

compatibility . . . . . . . . . . . . . . . . . . . . . .39

About DivX . . . . . . . . . . . . . . . . . . . . . . .40

About WMV. . . . . . . . . . . . . . . . . . . . . . .40

About MPEG-4 AAC. . . . . . . . . . . . . . . . .40

About WMA . . . . . . . . . . . . . . . . . . . . . .41

Using and taking care of discs . . . . . . . . .41

DVD Video regions . . . . . . . . . . . . . . . . .41

Installation and maintenance . . . . . . . . . .42

Hints on installation . . . . . . . . . . . . . . . .42

Cleaning the pickup lens. . . . . . . . . . . . .42

Problems with condensation. . . . . . . . . .42

Moving the system unit . . . . . . . . . . . . . .42

Screen sizes and disc formats . . . . . . . . . .42

Widescreen TV users. . . . . . . . . . . . . . . .43

Standard TV users. . . . . . . . . . . . . . . . . .43

Troubleshooting. . . . . . . . . . . . . . . . . . . . .44

General . . . . . . . . . . . . . . . . . . . . . . . . . .44

DVD/CD/Video CD player . . . . . . . . . . . .45

Tuner. . . . . . . . . . . . . . . . . . . . . . . . . . . .46

USB connection . . . . . . . . . . . . . . . . . . .46

HDMI connection . . . . . . . . . . . . . . . . . .47

Error Messages. . . . . . . . . . . . . . . . . . . .47

Resetting the system . . . . . . . . . . . . . . . . .48

Using the language code list . . . . . . . . . . .48

Language code list . . . . . . . . . . . . . . . . . .49

Country/Area code list. . . . . . . . . . . . . . . .49

Specifications . . . . . . . . . . . . . . . . . . . . . .50

HTZ373_777_EN.book Page 5 Wednesday, March 5, 2008 1:08 PM

Controls and displays01

6

En

Chapter 1

Controls and displays

Front panel

1

 OPEN/CLOSE

Opens/closes the disc tray.

2

 DVD/CD

Selects the DVD/CD function and starts/

pauses/resumes playback.

3



Stops playback.

4

 USB

Selects the USB function and starts/pauses

playback.

5

VOLUME +/–

buttons

6

 STANDBY/ON

Switches the system on or into standby.

7 Disc tray

8 Remote Sensor

9Display

See Display below.

10 PHONES jack

Connect headphones.

11

USB

interface

Connect a USB device for playback (see USB

playback on page 25).

COMPATIBLE

10 11

4 61 2 3

7 8 9

5

HTZ373_777_EN.book Page 6 Wednesday, March 5, 2008 1:08 PM

Controls and displays 01

7

En

English

FrançaisDeutsch

Nederlands

Italiano Español

Remote control

1

 STANDBY/ON

Switches the system on or into standby.

2 Function select buttons

Selects the source you want to listen to (DVD/

CD, TUNER, USB, LINE).

3 Number buttons, CLEAR,

DISPLAY

and

DVD controls

CLEAR

Clears an entry.

DISPLAY

Displays/changes disc information shown

on-screen (page 24).

SHIFT+AUDIO

Selects audio channel/language (page 23).

SHIFT+SUBTITLE

Displays/changes the subtitles (page 23).

SHIFT+ANGLE

Changes camera angle during DVD multi-

angle scene playback (page 24).

SHIFT+ZOOM

Changes the screen zoom level (page 23).

4

TOP MENU

–

Displays the top menu of a

DVD disc in the play position — this may

be the same as pressing MENU (page 13).

SHIFT+SETUP – Use to make various

system and surround sound settings

(page 14, 27, 35, 37 and 38).

5Cursor,

ENTER

and tuning buttons

/// – Use the cursor buttons to

navigate on-screen displays and menus.

ENTER – Selects an option or executes a

command.

TUNE +/– – Tunes the radio.

ST +/– – Selects station presets when

listening to the radio.

6HOME MENU – Displays (or exits) the on-

screen menu for Initial Settings, Play Mode

functions, etc.

SHIFT+MCACC – Starts the Auto MCACC

setup (page 11).

7 Sound controls

F.S.SURR – Selects Front Stage Surround

Advance mode (page 16).

SURROUND – Selects a Surround mode

(page 15) or switches to stereo playback

(page 16).

ADVANCED – Selects a Pioneer original

surround mode (page 16).

SOUND – Accesses the sound menu to

adjust the tone, bass and treble, etc.

(page 15 and 17).

HOME

MENU

PLAYLIST

STANDBY

/ON

SHIFT

LINE

TOP MENU

F.S.

SURR

SOUND

CLEAR

MUTE

SLEEP

DISPLAY

123

1

2

3

456

789

0

ADVANCED

TUNE

ST

USB

SUBTITLE

AUDIO

ZOOM

ANGLE

MENU

SR +

OPEN/CLOSE

INPUT CHANNEL VOLUME

DVD CD

TUNER

(FM/AM)

SOUND

RETRIEVER

VOLUME

TV CONTROL

SETUP

RETURN

TEST TONEMCACC

SURROUND

TUNE

ENTER

1

2

3

8

9

4

7

11

12

14

13

15

16

17

18

5

6

10

HTZ373_777_EN.book Page 7 Wednesday, March 5, 2008 1:08 PM

Controls and displays01

8

En

8 Playback controls

See Basic playback controls on page 12, Disc

playback features on page 18 and USB playback

on page 25 for an explanation of these

controls.

9 TV CONTROL buttons

These control Pioneer flat screen TVs.

10

SHIFT

Press to access the controls highlighted in

green.

11

SOUND RETRIEVER –

Press to restore CD

quality sound to compressed audio sources

(page 17).

12

 OPEN/CLOSE

Opens/closes the disc tray.

13 PLAYLIST buttons

Add tracks (during playback), or select a

playlist (while stopped) (page 20).

14

MENU – Press to display a USB menu, or

the Navigator (page 13 and 26).

SHIFT+SR+

– Sets the interlocking with the

connected flat screen TV (page 36).

15

RETURN – Returns to a previous menu

screen.

SHIFT+TEST TONE

– Outputs the test tone

(for speaker setup) (page 27).

16

SLEEP

Press to set the sleep timer (page 38).

17

MUTE

Mutes the sound (press again to cancel).

18

VOLUME +/–

Adjusts the volume.

HTZ373_777_EN.book Page 8 Wednesday, March 5, 2008 1:08 PM

Controls and displays 01

9

En

English

FrançaisDeutsch

Nederlands

Italiano Español

Display

1

DTS

Lights during playback of a DTS source (page 15).

2PRGSVE

Lights when progressive scan video signal is

given from the component video output

terminal (page 34).

3

SOUND

Lights when the Sound Retriever is active

(page 17).

4

SURR.

Lights when one of the Advanced surround

listening modes is selected (page 16).

F.SURR.

Lights when one of the Front Stage

Surround Advance mode is selected

(page 16).

5

RPT

and

RPT

-1

RPT lights during repeat play. RPT-1 lights

during repeat one-track play (page 21).

6

PGM

Lights during program play (page 20 and 22).

7 Tuner indicators

– Lights when a broadcast is being

received.

– Lights when a stereo FM broadcast is

being received in auto stereo mode.

– Lights when FM mono reception is

selected.

8

RDM

Lights during random play (page 21).

9 kHz/MHz

Indicates the frequency unit shown in the

character display (kHz for AM, MHz for FM).

10 Character display

11

Lights when sleep timer is active (page 38).

12



Lights during playback.

13

2

PL II

Lights during Dolby Pro Logic II decoding

(page 15).

14

2

D

Lights during playback of a Dolby Digital

source (page 15).

PRGSVE SOUND

DTS F.SURR.

2PL

2D

RPT -1

kHz

PGM

MHz RDM

6

12 89 7

5

1113

3

14

10

21 4

HTZ373_777_EN.book Page 9 Wednesday, March 5, 2008 1:08 PM

Getting started02

10

En

Chapter 2

Getting started

Home theater sound setup

Place your speakers as shown below for

optimal surround sound (see the Speaker

Setup Guide for more placement tips).

• Standard surround setup – This is a

standard multichannel surround sound

speaker setup for optimal 5.1 channel

home theater sound.

HTZ373DVD model speaker configuration:

HTZ777DVD model speaker configuration:

Depending on the size and characteristics of

your room, you can choose to use the following

setup option:

1

• Front surround setup – This setup is ideal

when rear surround speaker placement

isn’t possible or you want to avoid running

long speaker cables in your listening area.

HTZ373DVD model speaker configuration:

HTZ777DVD model speaker configuration:

After placing your speakers, see Using the

Auto MCACC setup for optimal surround sound

below to complete your surround setup.

Note

1See Using Front Stage Surround Advance on page 16 to select a front surround mode when using this setup.

Center Center

Front

left

Listening position

Front

right

Subwoofer

Surround

left

Surround

right

C

FL

FR

*When center speakers are placed in the center.

Surround left Surround right

Center

Front

left

Listening position

Front

right

Subwoofer

Listening position

Subwoofer

Center Center

Front

left

Front

right

Surround

left

Surround

right

SR

FL

SL

C

FR

*When center speakers are placed in the center.

Surround

left

Surround

right

Center

Front left

Listening position

Front right

SubwooferSubwoofer

HTZ373_777_EN.book Page 10 Wednesday, March 5, 2008 1:08 PM

Getting started 02

11

En

English

FrançaisDeutsch

Nederlands

Italiano Español

Using the Auto MCACC setup for

optimal surround sound

The Multichannel Acoustic Calibration (MCACC)

system measures the acoustic characteristics of

your listening area, taking into account ambient

noise and testing for channel delay and channel

level. After you have set up the microphone

provided with your system, the receiver uses the

information from a series of test tones to optimize

the speaker settings and equalization (Acoustic

Calibration EQ) for your particular room.

1

Important

• These test tones are loud; however, do not

turn the volume down during setup as this

may result in a sub-optimal calibration.

• Make sure the mic and speakers are not

moved during the MCACC setup.

1 Connect the microphone to the MCACC

MIC jack on the rear panel.

2 Place the microphone at your normal

listening position.

Place it about ear height, and make sure it is

level by using a table or chair.

Make sure there are no obstacles between the

speakers and the microphone.

3 If the system is off, press

 STANDBY/ON to turn the power on.

If the tuner is selected, switch the input

source.

4 Press SHIFT+MCACC.

Try to be as quiet as possible after pressing

SHIFT+MCACC. The volume increases

automatically and the system outputs a series

of test tones.

• Press SHIFT+MCACC to cancel and revert

to the previous Auto MCACC settings.

• If the noise level is too high, NOISY blinks

in the display for five seconds. To exit and

check the noise levels

2

, press

SHIFT+MCACC, or to try again, press

ENTER when RETRY shows in the display.

• If you see an ERR MIC or ERR SP message

in the display, there may be a problem with

your mic or the speaker connections. To try

again, press ENTER when you see RETRY.

3

When the MCACC setup is complete, the

volume level returns to normal and

COMPLETE

4

shows in the display, indicating

that the MCACC setup is complete and

Acoustic Calibration EQ has been activated.

5

Note

1 You only need to use the Auto MCACC setup once (unless you change the placement of your speakers or your room layout).

PLAYLIST

STANDBY

/ON

LINE

123

1

2

3

456

789

USB

SUBTITLE

AUDIO

ZOOM

ANGLE

OPEN/CLOSE

DVD CD

TUNER

(FM/AM)

SOUND

RETRIEVER

HOME

MENU

TOP MENU

RETURN

TEST TONEMCACC

SURROUND

SOUND

CLEAR DISPLAY

0

ADVANCED

TUNE

ST

ENTER

SETUP

SR

F.S.SURR

MENU

SHIFT

SLEEP

MUTE

INPUT CHANNEL VOLUME

VOLUME

TV CONTROL

VIDEO OUT

VIDEO

Y

P

R

P

B

COMPONENT

VIDEO

MCACC

SETUP MIC

DIGITAL IN

OPTICAL

LINE 1

CONTROL

IN

2 • If the room environment is not optimal for the Auto MCACC setup (too much ambient noise, echo off the walls, obstacles

blocking the speakers from the microphone) the final settings may be incorrect. Check for household appliances (air conditioner,

fridge, fan, etc.), that may be affecting the environment and switch them off if necessary.

• Some older TVs may interfere with the operation of the mic. If this seems to be happening, switch off the TV during the Auto

MCACC setup.

3 If this doesn’t work, press SHIFT+MCACC, turn off the power, and check the problem indicated by the error message, then try

the Auto MCACC setup again.

4If COMPLETE doesn’t appear, it is likely an error occurred during the setup. Please check all connections and try again.

5See Listening with Acoustic Calibration EQ on page 17 to switch on/off Acoustic Calibration EQ.

HTZ373_777_EN.book Page 11 Wednesday, March 5, 2008 1:08 PM

Getting started02

12

En

Using the on-screen displays

For ease of use, this system makes extensive

use of graphical on-screen displays (OSDs).

All the screens are navigated in basically the

same way, using , , ,  to change the

highlighted item and pressing ENTER to select

it.

1

Important

• Throughout this manual, ‘Select’ means

use the cursor buttons to highlight an item

on-screen, then press ENTER.

Tip

• The button guide at the bottom of every

OSD screen shows you which buttons

you’ll need to use for that screen.

Playing discs

The basic playback controls for playing DVD,

CD, Video CD/Super VCD, DivX video/WMV

and WMA/MP3/MPEG-4 AAC discs are

covered here.

Further functions are detailed in

chapter 4.

1 If the player isn’t already on, switch it on.

If you’re playing a disc with video, also turn on

your TV and make sure that it is set to the

correct video input.

2Press

 OPEN/CLOSE

to load a disc.

Load a disc with the label side facing up, using

the disc tray guide to align the disc (if you’re

loading a double-sided DVD disc, load it with

the side you want to play face down).

3Press



(play) to start playback.

If you’re playing a DVD or Video CD/Super VCD,

a menu may appear. See DVD-Video disc

menus and Video CD/Super VCD PBC menus on

page 13 to navigate these.

If you loaded a disc containing JPEGs, a

slideshow will start. See Playing a JPEG

slideshow on page 18 for more on this.

• If a disc contains a mixture of DivX video/

WMV and other media file types (MP3, for

example), first select whether to play the

DivX video/WMV files (DivX/WMV) or the

other media file types (MP3/WMA/JPEG/

MPEG-4 AAC) from the on-screen display.

4 Adjust the volume.

Use the VOLUME +/– control.

Basic playback controls

The following table shows the basic controls on

the remote for playing discs.

2

You can find

other playback features in chapter 4.

Note

1 The screen saver will appear after five minutes of inactivity.

Button What it does

HOME

MENU

Displays/exits the on-screen display

 Changes the highlighted menu item

ENTER

Selects the highlighted menu item

RETURN

Returns to the main menu without

saving changes

2 You may find with some DVD discs that some playback controls don’t work in certain parts of the disc.

Button What it does

 Starts/resumes normal playback.

• If the display shows RESUME or

LAST MEM playback starts from the

resume or last memory point (see

Resume and Last Memory below).

 Pauses/unpauses a disc.

HTZ373_777_EN.book Page 12 Wednesday, March 5, 2008 1:08 PM

Getting started 02

13

En

English

FrançaisDeutsch

Nederlands

Italiano Español

Resume and Last Memory

When you stop playback of a disc, RESUME

shows in the display indicating that you can

resume playback from that point.

With DVDs and Video CD/Super VCDs, even if

ejected, the play position is stored in memory.

1

The next time you load the disc, the display

shows LAST MEM and you can resume

playback.

If you want to clear the resume point, press

 (stop) while RESUME is displayed.

DVD-Video disc menus

Many DVD-Video discs contain menus from

which you can select what you want to watch.

Sometimes DVD-Video menus are displayed

automatically when you start playback; others only

appear when you press MENU or TOP MENU.

Video CD/Super VCD PBC menus

Some Video CD/Super VCDs have menus from

which you can choose what you want to watch.

These are PBC (Playback control) menus.

You can play a PBC Video CD/Super VCD

without having to navigate the PBC menu by

starting playback using a number button to

select a track, rather than the  (play) button.

 Stops playback or cancels the resume

function (if the display shows

RESUME

).

 Press to start fast reverse scanning.

 Press to start fast forward scanning.

 Skips to the start of the current track or

chapter, then previous tracks/chapters.

 Skips to the next track or chapter.

Numbers

Use to enter a title/chapter/track

number. Press

ENTER to select.

• If the disc is stopped, playback starts

from the selected title (for DVD) or

track (for CD/Video CD/Super VCD).

• If the disc is playing, playback jumps to

the start of the selected title (VR mode

DVD-R/-RW), chapter (DVD-Video) or

track (CD/Video CD/Super VCD).

Note

1 • The Resume and the Last Memory functions may not work with some discs.

• For DVD-Video discs (except VR mode DVD-R/-RW), the player stores the play position of the last five discs.

Button What it does

TOP MENU

Displays the ‘top menu’ of a DVD

disc — this varies with the disc.

Button What it does

MENU

Displays a DVD disc menu — this

varies with the disc and may be

the same as the ‘top menu’.

 Moves the cursor around the

screen.

ENTER

Selects the current menu option.

RETURN

Returns to the previously

displayed menu screen.

Numbers Highlights a numbered menu

option (some discs only). Press

ENTER to select.

Button What it does

RETURN

Displays the PBC menu.

Numbers Selects numbered menu options.

Press

ENTER to select.

 Displays the previous menu page

(if there is one).

 Displays the next menu page

(if there is one).

Button What it does

HTZ373_777_EN.book Page 13 Wednesday, March 5, 2008 1:08 PM

Getting started02

14

En

Listening to the radio

The tuner can receive both FM and AM

broadcasts, and lets you memorize your

favorite stations so you don’t have to manually

tune in every time you want to listen.

1 Press

TUNER

to switch to the tuner, then

press repeatedly to select the AM or FM band.

The display shows the band and frequency.

2 Tune to a frequency.

There are three tuning modes — manual, auto,

and high-speed:

• Manual tuning: Press TUNE +/–

repeatedly to change the displayed

frequency.

• Auto tuning: Press and hold TUNE +/–

until the frequency display starts to move,

then release. The tuner will stop on the next

station it finds. Repeat to keep searching.

• High-speed tuning: Press and hold

TUNE +/– until the frequency display starts

to move rapidly. Keep the button held down

until you reach the frequency you want. If

necessary, fine tune the frequency using

the manual tuning method.

Improving poor FM reception

If you’re listening to an FM station in stereo but

the reception is weak, you can improve the

sound quality by switching to mono.

1 Tune to an FM radio station then press

SHIFT+SETUP

.

2Use

/

to choose FM MODE then press

ENTER

.

3Use

/

to select

FM MONO

then press

ENTER

.

The mono indicator ( ) lights when the tuner

is in mono reception mode.

Select FM AUTO above to switch back to auto-

stereo mode (the stereo indicator ( ) lights

when receiving a stereo broadcast).

Memorizing stations

You can save up to 30 station presets so that

you always have easy access to your favorite

stations without having to tune in manually

each time.

1 Tune to an AM or FM radio station.

Select mono or auto-stereo reception (FM)

as necessary. These settings are saved along

with the preset.

2Press

SHIFT+SETUP

and use

/

to

choose ‘ST.MEM.’ then press

ENTER

.

3Use

/

to select the station preset you

want then press

ENTER

.

Listening to station presets

1 Make sure the

TUNER

function is

selected.

2Use the

ST +/–

buttons to select a station

preset.

• You can also use the number buttons to do

this.

Listening to other sources

You can connect auxiliary sources (TV, satellite

receiver, etc.) to this unit for playback through

the speaker system. See Connecting auxiliary

components on page 33 for more on this.

• To connect a USB device to the USB

terminal, see USB playback on page 25.

1 Make sure that the external source (TV,

satellite receiver, etc.) is switched on.

2Press

LINE

to select the source.

Each press switches between LINE

1

and LINE

2

.

3 If necessary, start playback of the source.

HTZ373_777_EN.book Page 14 Wednesday, March 5, 2008 1:08 PM

Listening to your system 03

15

En

English

FrançaisDeutsch

Nederlands

Italiano Español

Chapter 3

Listening to your system

Auto listening mode

The Auto listening mode is the simplest way to

listen to any source as it was mastered: the

output from the speakers mirrors the channels

in the source material.

• If you set up the system for Front surround

(page 10), the Front Surround modes will

give the best results.

• Press

SURROUND

to select the AUTO

listening mode.

1

Listening in surround sound

You can listen to stereo or multichannel

sources in surround sound.

2

Surround sound

is generated from stereo sources using one of

the Dolby Pro Logic decoding modes.

• If you set up the system for Front surround

(page 10), the Front Surround modes will

give the best results.

• Press

SURROUND

repeatedly to select a

listening mode.

1

The choices that appear in the display will vary

according to the type of source that’s playing.

• AUTO – Auto listening mode (see above)

• DOLBY PL (Dolby Pro Logic) – 4.1 channel

surround sound (use with any two-channel

source)

• MOVIE (Dolby Pro Logic II Movie) – Pro

Logic II 5.1 channel surround sound,

especially suited to movie sources (use

with any two-channel source)

• MUSIC (Dolby Pro Logic II Music) – Pro

Logic II 5.1 channel surround sound,

especially suited to music sources (use

with any two-channel source)

• STEREO – See Listening in stereo below

Dolby Pro Logic II Music settings

When listening in Dolby Pro Logic II Music

mode, there are three settings you can adjust:

Center Width, Dimension, and Panorama.

1 With Dolby Pro Logic II Music mode

active, press

SOUND

.

2Use

/

to select ‘C WIDTH’, ‘DIMEN.’ or

‘PANORAMA’ then press

ENTER

to confirm.

• C WIDTH (Center Width) – Provides a

better blend of the front speakers by

spreading the center channel between the

front right and left speakers, making it

sound wider (higher settings) or narrower

(lower settings).

• DIMEN. (Dimension) – Adjusts the depth

of the surround sound balance from front

to back, making the sound more distant

(minus settings), or more forward (positive

settings).

• PANORAMA – Extends the front stereo

image to include the surround speakers for

a ‘wraparound’ effect.

Note

1 If the source is Dolby Digital or DTS, the corresponding indicator lights in the front panel display.

2 Note that when the tuner is selected, multichannel playback is not possible.

TEST TONEMCACC

SURROUND

SOUND

ADVANCED

TUNE

F.S.SURR

TEST TONEMCACC

SURROUND

SOUND

ADVANCED

TUNE

F.S.SURR

HTZ373_777_EN.book Page 15 Wednesday, March 5, 2008 1:08 PM

Listening to your system03

16

En

Using Front Stage Surround

Advance

The Front Stage Surround Advance modes are

effective when you are using the Front

surround speaker setup as described on

page 10.

1

• Press F.S.SURR to select a Front Stage

Surround Advance mode.

Press repeatedly to select FOCUS5.1, WIDE5.1

or EXTRAPWR.

• FOCUS5.1 – Use to provide a rich surround

sound effect directed to the center area

where the left and right speakers’ sound

projection converges.

• WIDE5.1 – Use to provide a surround

sound effect to a wider area than

FOCUS5.1 mode.

• EXTRAPWR – Outputs stereo sound (in the

case of multi-channel sources,

down-mixed stereo sound) from the

surround speakers for powerful stereo

effect.

Using Advanced Surround

The Advanced Surround effects can be used

with any multichannel or stereo source for a

variety of additional surround sound effects.

1

These modes are designed to provide optimum

listening effect when using the Standard

surround setup described on page 10.

•Press

ADVANCED

to select an Advanced

Surround mode.

Press repeatedly to select ACTION,

UNPLUGED, EXPANDED, TV SURR., SPORTS,

ADV.GAME, VIRTUAL or X-STEREO

(Extended Stereo).

Listening in stereo

You can listen to any source — stereo or

multichannel — in stereo. When playing a

multichannel source, all channels are

downmixed to the front left/right speakers and

the subwoofer.

•Press

SURROUND

repeatedly until

STEREO shows in the display.

Listening with headphones

When headphones are connected, only the

STEREO

(default) and PHONES SURROUND

(virtual surround sound for headphones)

modes are available.

• With headphones connected, press

ADVANCED

to select

PHONES SURROUND

or

SURROUND

to select STEREO

.

Note

1 Note that when the tuner is selected, multichannel playback is not possible.

HOME

MENU

TOP MENU

RETURN

TEST TONEMCACC

SURROUND

SOUND

0

ADVANCED

TUNE

ST

ENTER

SETUP

SR

F.S.SURR

MENU

TEST

TONEMCACC

SURROUND

SOUND

ADVANCED

TUNE

F.S.SURR

TE

S

T T

O

NEM

C

A

CC

SURROUND

SOUND

ADVANCED

TUNE

F.S.SURR

HTZ373_777_EN.book Page 16 Wednesday, March 5, 2008 1:08 PM

Listening to your system 03

17

En

English

FrançaisDeutsch

Nederlands

Italiano Español

Listening with Acoustic

Calibration EQ

You can listen to sources using the Acoustic

Calibration Equalization set in Using the Auto

MCACC setup for optimal surround sound on

page 11.

1

1 Press

SOUND

and use

/

to select

MCACC EQ then press

ENTER

.

2Use

/

to select EQ ON or EQ OFF

then

press ENTER to confirm

.

•If you select EQ OFF, equalization is set to

off but speaker settings (channel delay and

channel level) remain in effect.

•

EQ ON

is selected automatically after the

Auto MCACC setup is completed.

Using the Sound Retriever

When audio data is removed during the WMA/

MP3/MPEG-4 AAC compression process, sound

quality often suffers from an uneven sound

image. The Sound Retriever feature employs new

DSP technology that helps bring CD quality

sound back to compressed 2-channel audio by

restoring sound pressure and smoothing jagged

artifacts left over after compression.

• While listening to a stereo source, press

SOUND RETRIEVER to switch the sound

retriever on or off.

Enhancing dialogue

The Dialogue Enhancement feature is designed

to make the dialogue stand out from other

background sounds in a TV or movie soundtrack.

1 Press

SOUND

and use

/

to select

DIALOGUE

then press

ENTER

.

2Use

/

to select the amount of

dialogue enhancement then press

ENTER

to

confirm.

Select between OFF, MID or MAX.

Using the Tone controls

You can change the tonal balance of the sound

by using the tone control menu.

1 Press

SOUND

and use

/

to select

TONE then press

ENTER

.

2Use

/

to select the option you want to

adjust and press

ENTER

.

The Bass/Treble, Quiet and Midnight features

cannot be used at the same time.

Adjusting the bass and treble

Use the tone controls to adjust the bass and

treble.

•Use

/

to select BASS or TREBLE then

use

/

to adjust the tone.

Press ENTER to

confirm

.

Quiet and Midnight modes

The Quiet listening feature reduces excessive

bass or treble in a sound source.

The Midnight listening feature allows you to

hear effective surround sound of movies at low

volume levels.

• After pressing

ENTER, the setting

switches on/off.

• To cancel the Quiet or Midnight listening

modes, select BASS/TRE.

Boosting the bass level

There are two bass modes you can use to

enhance the bass in a source.

2

1 Press

SOUND

and use

/

to select

BASSMODE then press

ENTER

.

2Use

/

to adjust the sound

then press

ENTER to confirm

.

Select between OFF, MUSIC or CINEMA.

Note

1 Acoustic Calibration EQ is not available when headphones are connected.

2 The Bass Mode is not available when headphones are connected.

HTZ373_777_EN.book Page 17 Wednesday, March 5, 2008 1:08 PM

Disc playback features04

18

En

Chapter 4

Disc playback features

Important

• Many of the functions covered in this

chapter apply to DVD discs, Video CDs/

Super VCDs, CDs, DivX video/WMV and

WMA/MP3/MPEG-4 AAC/JPEG discs,

although the exact operation of some

varies slightly with the kind of disc loaded.

• Some DVDs restrict the use of some

functions (random or repeat, for example)

in some or all parts of the disc. This is not a

malfunction.

• When playing Video CD/Super VCDs, some

of the functions are not available during

PBC playback. If you want to use them,

start the disc playing using a number

button to select a track.

Scanning discs

You can fast-scan discs forward or backward at

various different speeds.

1

• During playback, press



or



to start

scanning.

Press repeatedly to increase the scanning

speed (shown on-screen).

• To resume playback, press  (play).

2

Playing in slow motion

You can play DVDs, Video CD/Super VCDs and

DivX video/WMV at four different forward slow

motion speeds. DVD discs can also be played

in reverse slow motion.

1 During playback, press



(pause).

2 Press and hold

/

or

/

until slow

motion playback starts.

Press repeatedly to change the slow motion

speed (shown on-screen).

• To resume playback, press  (play).

2

Frame advance/frame reverse

You can advance or back up DVD discs frame-

by-frame. With Video CD/Super VCDs and DivX

video/WMV you can only use frame advance.

1 During playback, press



(pause).

2Press

/

or

/

to reverse or

advance a frame at a time.

• To resume playback, press  (play).

2

Playing a JPEG slideshow

After loading a disc containing JPEG pictures,

press  to start a slideshow from the first

folder/picture on the disc.

3

The player displays

the pictures in each folder in alphabetical

order.

• If the disc contains WMA/MP3/MPEG-4

AAC files, playback of the slideshow and

audio files repeats. During audio playback,

you can still use the skip (/), scan

(/) and pause () functions.

Pictures are automatically adjusted so that

they fill as much of the screen as possible.

Note

1 Only one speed is available for DivX video/WMV discs.

2 • Depending on the disc, normal playback may automatically resume when a new chapter is reached on a DVD disc.

• For Video CDs/Super VCDs in PBC mode and WMA/MP3/MPEG-4 AAC tracks (in Scan mode only), normal playback resumes

when you reach the beginning or the end of track.

3 • The time it takes for the player to load a file increases with large file sizes.

• Discs can contain up to 299 folders and up to 648 folders and files combined.

HTZ373_777_EN.book Page 18 Wednesday, March 5, 2008 1:08 PM

Disc playback features 04

19

En

English

FrançaisDeutsch

Nederlands

Italiano Español

While the slideshow is running:

Browsing DVD or Video CD/

Super VCD discs with the Disc

Navigator

Use the Disc Navigator to browse through the

contents of a DVD or Video CD/Super VCD disc

to find the part you want to play.

1 During playback, press HOME MENU

and select ‘Disc Navigator’ from the on-

screen menu.

2 Select a view option.

The options available depend on the kind of

disc loaded and whether the disc is playing or

not, but include:

• Title – Titles from a DVD-Video disc.

• Chapter – Chapters from the current title

of a DVD-Video disc.

• Track – Tracks from a Video CD/Super VCD

disc.

• Time – Thumbnails from a Video CD/Super

VCD disc at 10 minute intervals.

• Original: Title – Original titles from a VR

mode DVD-R/-RW disc.

• Playlist: Title – Playlist titles from a VR

mode DVD-R/-RW disc.

• Original: Time – Thumbnails from the

Original content at 10 minute intervals.

• Playlist: Time – Thumbnails from the

Playlist at 10 minute intervals.

The screen shows up to six moving thumbnail

images displayed one after another. To display

the previous/next six thumbnails, press /

.

3 Select the thumbnail image for what

you want to play.

You can use either /// and ENTER to

select a thumbnail, or the number buttons.

To select using the number buttons, enter a

two-digit number then press ENTER.

Button What it does

 Pauses the slideshow (or audio);

press again to restart.

 Jumps to the previous picture (or

audio file with audio playback).

 Jumps to the next picture (or

audio file with audio playback).

///

Pauses the slideshow and

rotates/flips the displayed

picture (Press  (play) to restart

slideshow).

SHIFT+

ZOOM

Pauses the slideshow and zooms

the picture. Press again to toggle

between 1x, 2x and 4x zoom

(Press  (play) to restart

slideshow).

MENU

Displays the Disc Navigator

screen (see below).

Disc Navigator

Title

Chapter

01

04

02

05

03

06

Disc Navigator: Title

01- 49: - -

HTZ373_777_EN.book Page 19 Wednesday, March 5, 2008 1:08 PM

Disc playback features04

20

En

Browsing Windows Media

TM

Audio (WMA), MP3, MPEG-4

AAC, DivX video/WMV and JPEG

files with the Disc Navigator

Use the Disc Navigator to find a particular file

or folder by filename.

1 Press HOME MENU and select ‘Disc

Navigator’ from the on-screen menu.

2Use /// and ENTER to navigate.

Use / to move up and down the folder/file

list.

Use  to return to the parent folder.

1

Use ENTER or  to open a highlighted folder.

• When a JPEG file is highlighted, a

thumbnail image is displayed on the right.

3 To play the highlighted track or DivX

video/WMV file or display the highlighted

JPEG file, press ENTER.

• When a WMA/MP3/MPEG-4 AAC or DivX

video/WMV file is selected, playback

begins from that file, and continues until

the end of the folder.

• When a JPEG file is selected, a slideshow

begins, starting with that file, and

continues to the end of the folder.

Tip

• You can also play a JPEG slideshow while

listening to WMA/MP3/MPEG-4 AAC

playback. Simply select the audio file you

want to listen to followed by the JPEG from

which you want the slideshow to start.

Playback of both the slideshow and the

audio files repeats. Playback controls are

effective for the JPEG slideshow only.

• To play the contents of the whole disc

rather than just the current folder, exit the

Disc Navigator and start playback using

the  (play) button.

Using Playlists

With this feature, you can make up to three

playlists of 30 files each for discs containing

WMA, MP3, MPEG-4 AAC and JPEG files.

Since this unit will remember all playlists for

the last ten discs you have loaded, this is useful

if you have a large number of files that you want

to organize quickly and easily.

2

Programming playlists

1 With the disc stopped, press HOME

MENU and select ‘Disc Navigator’ from the

on-screen menu.

2 Select the file you want to add to the

play

list.

See Browsing Windows Media

TM

Audio (WMA),

MP3, MPEG-4 AAC, DivX video/WMV and JPEG

files with the Disc Navigator above if you don’t

know how to do this.

3Press

PLAYLIST

1, 2 or 3.

The file is added to the playlist you select.

4 Repeat steps 2 and 3 until you’re done.

Note

1 You can also do this by going to the ‘..’ folder at the top, then pressing ENTER.

00:00/ 00:00 0kbps

Folder1

Folder2

Folder3

Folder4

File1

File2

File3

File4

File5

Folder2

00:00/ 00:00 0kbps

2 The disc must be loaded for the files in your playlist to play back.

HTZ373_777_EN.book Page 20 Wednesday, March 5, 2008 1:08 PM

ページが読み込まれています...

Pioneer XV-DV373 Operating Instructions Manual

このマニュアルも適しています

Pioneer XV-DV373 Operating Instructions Manual

他の言語で

関連論文

その他のドキュメント