Yamaha DVD-S661 取扱説明書

i

DVD PLAYER

L

DVD-S661

1

To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean

place — away from direct sunlight, heat sources,

vibration, dust, moisture, or cold. In a cabinet, allow

about 2.5 cm (1 inch) of free space all around this unit

for adequate ventilation.

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot, nor locate this unit in an environment

with high humidity (i.e., a room with a humidifier) to

prevent condensation inside this unit, which may cause

an electrical shock, fire, damage to this unit, and/or

personal injury.

5 Avoid installing this unit in a location where foreign

objects may fall onto this unit or where this unit may be

exposed to liquid dripping or splashing. On the top of

this unit, do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Burning objects (i.e., candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall,

spilling the liquid and causing an electrical shock

to the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use excessive force on switches, knobs and/or

cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Use only the voltage specified on this unit. Using this

unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage

other than as specified.

13 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any service is

needed. The cabinet should never be opened for any

reason.

14 When not planning to use this unit for long periods of

time (i.e., vacation), disconnect the AC power plug

from the wall outlet.

15 Be sure to read the “Troubleshooting” section on

common operating errors before concluding that this

unit is faulty.

16 Before moving this unit, press STANDBY/ON to set

the unit in standby mode, then disconnect the AC power

plug from the wall outlet.

17 Install this unit near the AC outlet and where the AC

power plug can be reached easily.

18 The batteries shall not be exposed to excessive heat

such as sunshine, fire or the like.

LASER SAFETY

This unit employs a laser. Due to possible eye injury, only a

qualified service person should remove the cover or attempt

to service this device.

DANGER

This unit emits visible laser radiation when open. Avoid

direct eye exposure to beam.

When this unit is plugged into a wall outlet, do not place

your eyes close to the opening of the disc tray and other

openings or look inside.

CAUTION: READ THIS BEFORE OPERATING THIS UNIT.

The unit is not disconnected from the AC power source

as long as it is connected to the wall outlet, even if this

unit itself is turned off. This state is called the standby

mode. In this state, this unit is designed to consume a

very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

AVOID DIRECT EXPOSURE TO THE BEAM

INVISIBLE LASER RADIATION WHEN OPEN

DANGER:

DO NOT STARE INTO BEAM

INVISIBLE LASER RADIATION WHEN OPEN

CAUTION:

Contents

English

1 En

Introduction ..................................3

Supplied accessories ................................. 3

Region codes .............................................. 3

Playable disc formats ................................. 3

Cleaning discs ............................................. 4

Patent information ...................................... 4

Functional Overview ....................5

Front panel ..................................................5

Rear panel .................................................... 6

Remote control ............................................ 7

Connections ..................................8

General notes on connections .................. 8

Audio connections ...................................... 8

Digital connection ..............................................8

Analog connection ..............................................8

Video connections ...................................... 9

Component video jacks <A> ..............................9

S-video jack <B> ................................................9

Composite video jack <C> .................................9

HDMI connection ....................................... 10

HDMI jack ........................................................10

Other connections ....................................11

USB port ...........................................................11

Remote control jacks ........................................11

Getting Started ...........................12

Step 1: Inserting batteries into

the remote control .................................... 12

Using the remote control ..................................12

Step 2: Turning on the power .................. 12

Step 3: Setting a TV type/display and

language ....................................................13

Setting a color system for your TV ..................13

Setting an aspect ratio for your TV ..................13

Setting the OSD language ................................14

Setting the audio, subtitle and disc menu

languages (DVD-Video only) ..........................14

Playback Operation ................... 15

Basic operation ......................................... 15

Selecting a track/chapter ..................................15

Searching backward/forward ...........................15

Repeat/Shuffle functions ......................... 15

Repeat/Shuffle playback .................................. 15

Repeating a section within a chapter/track ......16

Operations for video playback

(DVD/VCD/SVCD) ...................................... 16

Using the disc menu .........................................16

Playback in slow motion ..................................16

Zooming pictures in/out ...................................16

Resuming playback from the last

stopped point .................................................... 16

Using the on-screen display (OSD) .................17

Special DVD features ............................... 18

Playing by title .................................................18

Selecting an audio language/format

and subtitle language ........................................ 18

Special VCD/SVCD features ..................... 18

Using the playback control (PBC) menu ......... 18

Playing data discs (MP3/WMA/

JPEG/DivX) ................................................ 18

Selecting a folder and track/file .......................19

Special picture disc features ................... 19

Using the preview function ..............................19

Zooming pictures in/out ...................................19

Playback with multi-angles ..............................20

Playing MP3 music and JPEG picture

simultaneously .................................................20

Special DivX features ............................... 20

Using the interactive menu ..............................20

Selecting an audio/subtitle language ................20

Using a USB device .................................. 21

Supported USB devices ................................... 21

Playing data files ..............................................21

Contents

2 En

Setup Menu .................................22

General setup menu ................................. 22

Locking/Unlocking the disc for viewing ..........22

Dimming the front panel display ......................22

Programming disc tracks (except MP3/

WMA/JPEG/DivX) ..........................................22

OSD language ..................................................23

Setting the screen saver ....................................23

Setting the sleep timer ......................................24

Setting the auto standby function .....................24

Displaying the DivX

®

VOD

registration code ...............................................24

Audio setup menu ..................................... 24

Setting the analog output ..................................25

Setting the digital output ..................................25

Turning the HDMI audio on/off .......................25

Turning the night mode on/off .........................26

Setting the lip synchronization .........................26

Video setup menu ..................................... 26

TV type .............................................................26

Setting the TV display ......................................27

Turning the progressive scan function on/off

...27

Adjusting picture settings .................................28

Setting the HDMI video ...................................29

Preference setup menu ............................ 30

Audio, subtitle and disc menu ..........................30

Restricting playback with parental control .......30

Selecting playback of VR format .....................30

Selecting the MP3/JPEG menu ........................31

Displaying DivX external subtitle files ............31

Selecting the PBC (playback control)

function .............................................................32

Changing the password ....................................32

Resetting the system .........................................32

Language Codes ........................ 33

Troubleshooting ......................... 34

Glossary ...................................... 37

Specifications ............................. 39

3 En

Introduction

English

Thank you for purchasing this unit. This

owner’s manual explains the basic operation

of this unit.

This manual is printed prior to production.

Design and specifications are subject to

change in part as a result of improvements,

etc. In case of differences between the manual

and the product, the product has priority.

• Remote control

• Two batteries (AAA, R03, UM-4) for the

remote control

• Audio/Video pin cable

• Owner’s manual

This unit is designed to support the region

management system. Check the regional code

number on the DVD disc package. If the

number does not match the region code of this

unit (see the table below or the back of this

unit), this unit may be unable to play the disc.

This unit can play the disc types associated

This unit is designed for use with discs having

the logos shown below. Do not attempt to load

any other type of disc into this unit.

This unit can play:

• DVD-R/RW/R DL and DVD+R/RW/R DL

discs recorded in DVD-Video compatible

format

• DVD-RW discs recorded in VR format

(compatible with CPRM)

• MP3, WMA and JPEG files recorded on

CD-R/RW, DVD-R/RW, DVD+R/RW and

USB

• KODAK picture CDs, FUJICOLOR CDs

• ISO 9660 Level1/Level2 for CD-R/RW

•

Up to 298 folders per disc/USB device and up

to 648 files per folder with up to 8 hierarchies

•DivX

®

files recorded on CD-R/RW,

DVD-R/RW, DVD+R/RW and USB

– Official DivX

®

Ultra Certified product

– Plays all versions of DivX

®

video (including

DivX

®

6) with enhanced playback of DivX

®

media files and the DivX

®

Media Format

• CD-R/RW, DVD-R/RW

/R DL

and DVD+R/RW

/

R DL

cannot be played unless finalized.

• Progressive JPEG and copyright-protected WMA

files cannot be played with this unit.

• Only the first session of DVD-R/RW

/R DL and

DVD+R

/R DL

can be played.

• Some discs cannot be played depending on disc

characteristics or recording conditions.

• Do not use any non-standard shaped discs

(heart-shaped, etc.).

• Do not use discs with tape, seals, paste or many

scratches on their surface.

• For details about playable formats, see

“Specifications” on page 39.

Supplied accessories

Region codes

Destination

Region

code of

this unit

Playable

discs

U.S.A.,

Canada

U.K.,

Europe

Asia,

Korea

Australia,

Central and

South America

1

ALL

2

ALL

3

ALL

4

ALL

Playable disc formats

Notes

Introduction

4 En

Introduction

• When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center out.

Do not wipe in a circular motion.

• Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic

spray intended for analog records.

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are

trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Out” are registered trademarks of DTS, Inc.

DivX, DivX Ultra Certified, and associated logos are trademarks of DivX, Inc. and are used under license.

HDMI, the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of

HDMI Licensing LLC.

Cleaning discs

Patent information

This product incorporates copyright protection technology that is protected by method claims of certain

U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights

owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and

is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision

Corporation. Reverse engineering or disassembly is prohibited.

5 En

Functional Overview

English

1 STANDBY/ON

Turns on this unit or sets it to the standby mode.

2 Disc tray

Loads a disc in the disc tray.

3 OPEN/CLOSE ( )

Opens or closes the disc tray.

4 HDMI indicator

Lights up when an HDMI component is

connected, and signals output via the HDMI

jack of this unit.

5 PROGRESSIVE indicator

Lights up when this unit enters the progressive

mode.

6 Front panel display

Shows the current status of this unit.

7 PLAY ( p )

Starts playback.

8 PAUSE (   )

Pauses playback.

9 STOP ( s )

Stops playback.

0 USB port

Connect to the USB port of your USB device

(see page 11).

Front panel

1 2354 6 7 8 9 0

Functional Overview

6 En

Functional Overview

1 AC power cable

Plug the power cable into the AC wall outlet.

2 REMOTE CONTROL (IN, OUT) jacks

Connect the REMOTE CONTROL (IN) jack of

this unit to the remote control output jack of

your Yamaha AV receiver.

Connect the REMOTE CONTROL (OUT) jack

of this unit to the remote control input jack of

your Yamaha component (see page 11).

3 HDMI jack

Connect to the HDMI input jack of your HDMI

component (see page 10).

4 AUDIO OUT (L, R) jacks

Connect to the audio input jacks of your AV

receiver or stereo system (see page 8).

5 DIGITAL OUT - COAXIAL jack

Connect to the coaxial input jack of your AV

receiver (see page 8).

6 VIDEO OUT - COMPONENT (Y, PB, PR)

jacks

Connect to the component input jacks of your

AV receiver (see page 9).

7 VIDEO OUT - S VIDEO jack

Connect to the S-video input jack of your AV

receiver (see page 9).

8 VIDEO OUT - VIDEO jack

Connect to the composite video input jack of

your AV receiver (see page 9).

Caution: Do not touch the inner pins of the jacks on the rear panel of this unit.

Electrostatic discharge may cause permanent damage to this unit.

Rear panel

REMOTE CONTROL

OUT

HDMI

AUDIO OUT

COMPONENT VIDEO

S VIDEOCOAXIAL

P

R

PB

Y

VIDEO OUTDIGITAL OUT

IN

14567832

7 En

Functional Overview

English

1

Turns on this unit or sets it to the standby mode.

2 TOP MENU/RETURN

Displays the top-level disc menu (DVD).

Moves back to the previous menu (DVD*/VCD)

(see page 18).

3 2 / 3 /5 /a

Selects an item in the currently displayed menu.

Search or slow playback.

ENTER

Confirms the menu selection.

4 MENU

Displays the menu of a disc (DVD/JPEG)

(see pages 16, 18, 19 and 20).

Switches PBC on or off (VCD) (see page 18).

5 l22

Moves to the previous chapter or track.

Searches backward.*

6

7

Stops playback.

Opens the disc tray.*

7 Numeric buttons (0-9)

Selects numbered items in the currently

displayed menu.

8 SUBTITLE

Selects the subtitle language (see pages 18 and

20).

9 ZOOM

Enlarges the video image (see pages 16 and 19).

0 ON SCREEN

Accesses or exits from the on-screen display

(OSD) menu of this unit (see page 17).

q SET UP

Accesses or exits from the setup menu of this

unit (see pages 13 and 22).

w 33l

Moves to the next chapter or track.

Searches forward.*

e 3 / 8

Starts or pauses playback.

r USB

Accesses the contents of the connected USB

device or exits from the USB mode (see

page 21).

t AUDIO

Selects the audio language or format (see

pages 18 and 20).

y REPEAT

Accesses or exits from the repeat/shuffle mode

(see page 15).

u REPEAT A-B

Repeats a specific segment (see page 16).

* Press and hold the button for about two seconds.

Remote control

1

2

3

u

y

t

r

e

w

q

0

5

6

7

8

9

4

8 En

Connections

Be sure to turn off this unit and unplug the

power cable before you make or change

connections.

• Depending on the component you want to

connect, there are various ways to make

connections. Possible connections are

described below.

• Refer to the manuals supplied with your

other components as necessary to make the

best connections.

• Do not connect this unit via your VCR. The

video quality could be distorted by the copy

protection system.

• Do not connect the audio out jack of this unit

to the phono in jack of your audio system.

Digital connection

This unit has a digital coaxial output jack.

Connect the DIGITAL OUT - COAXIAL jack

of this unit to your AV receiver equipped with

a Dolby Digital, DTS, or MPEG decoder

using a commercially available coaxial cable.

• You need to set [DIGITAL OUTPUT] to [ALL]

(see “DIGITAL OUTPUT” on page 25).

• If the audio format of the digital output does not

match the capabilities of your receiver, the

receiver produces a distorted sound or no sound

at all. Make sure to select the appropriate audio

format from the menu screen on the disc.

Pressing AUDIO on the remote control once or

more may change not only the audio languages

but also the audio format. The selected format

appears in the front panel display for several

seconds.

• If you want to enjoy Dolby Digital, DTS and

MPEG formats, you must connect this unit to an

AV receiver that supports these formats.

Analog connection

This unit has 2-ch analog output jacks.

Connect the AUDIO OUT (L, R) jacks of this

unit to the corresponding input jacks of your

audio component (such as a stereo amplifier)

using the supplied audio pin cable.

General notes on connections

Audio connections

AUDIO OUT

COMPONENT VIDEO

S VIDEOCOAXIAL

P

R

PB

Y

VIDEO OUTDIGITAL OUT

C

This unit

AV receiver

Speakers

Notes

AUDIO OUT

COMPONENT VIDEO

S VIDEOCOAXIAL

P

R

PB

Y

VIDEO OUTDIGITAL OUT

L

R

L

R

L

This unit

Stereo

amplifier

Audio pin cable

(supplied)

Speakers

Connections

9 En

Connections

English

If your AV receiver has video output jacks,

connect your receiver and then your TV so

that you can use one TV for several different

video sources (LD, VCR, etc.) by simply

switching the input source selector of your

receiver.

This unit has several types of video output

jacks. Use the one that corresponds to the

input jacks of the component to be connected.

Component video jacks <A>

Component video connections achieve higher

fidelity color reproduction than S-video

connections by transmitting video signals on

separate wires for luminance (Y: green) and

chrominance (P

B: blue, PR: red).

Connect the VIDEO OUT - COMPONENT

(Y, PB, PR) jacks of this unit to component

input jacks of your AV receiver and then to

those of your TV using a commercially

available component cable. Observe the color

of each jack when you make connections.

If your receiver does not have component

output jacks, you can achieve a better video

image by connecting the component output

jacks of this unit directly to the component

input jacks of your TV.

S-video jack <B>

S-video connections achieve a clearer picture

than composite video connections by

transmitting video signals on separate wires

for luminance (Y) and chrominance (C).

Connect the VIDEO OUT - S VIDEO jack of

this unit to an S-video input jack of your AV

receiver and then to that of your TV using a

commercially available S-video cable.

Composite video jack <C>

Connect the VIDEO OUT - VIDEO jack of

this unit to a video input jack of your AV

receiver and then to that of your TV using the

supplied video pin cable.

Video connections

AUDIO OUT

COMPONENT

VIDEO

S VIDEOCOAXIAL

P

R

PB

Y

VIDEO OUTDIGITAL OUT

VIDEO

OUT

VIDEO

IN

S VIDEO

OUT

COMPONENT

VIDEO OUT

COMPONENT

VIDEO IN

S VIDEO

IN

COMPONENT

VIDEO IN

S VIDEO

INPUT

VIDEO

INPUT

YPBPR

PR

Y

PB

PR

Y

PB

S

V

S

V

Video pin

cable

(supplied)

AV receiver

TV

This unit

10 En

Connections

HDMI jack

HDMI provides high quality digital audio and

video on a single connection.

Connect the HDMI jack of this unit to an

HDMI input jack of your AV receiver, and

then to that of your TV using a commercially

available HDMI cable.

If your receiver does not have an HDMI input

jack, you can achieve a better video image by

connecting the HDMI jack of this unit directly

to the HDMI input jack of your TV.

This unit can display High-Definition JPEG

images (720p or 1080i) when you connect this

unit to an HDTV via the HDMI jack. For

details, see “HD JPEG” on page 29.

• You need to set [HDMI AUDIO] (see page 25)

and [HDMI VIDEO] (see page 29).

• You need to make an appropriate audio

connections if the connected component does not

output audio signals (see “Audio connections” on

page 8).

• This unit is not compatible with HDCP-

incompatible HDMI or DVI components.

• You need a commercially available HDMI/DVI

conversion cable when you connect this unit to

other DVI components. In this case, the HDMI

jack of this unit does not output any audio

signals.

• Depending on the connected DVI component,

black and white in the image may not be distinct.

In that case, adjust the picture setting of the

connected DVI component.

• Do not disconnect or turn off the power of the

HDMI/DVI component connected to the HDMI

jack of this unit while data is being transferred.

Doing so may disrupt playback or cause noise.

• When connecting an HDMI component, refer to

the manual supplied with your component.

HDMI connection

AUDIO OUT

COMPONENT VIDEO

HDMI

S VIDEOCOAXIAL

P

R

PB

Y

VIDEO OUT

DIGITAL OUT

HDMI IN

HDMI OUT

HDMI IN

HDMI cable

TV

This unit

AV receiver

Notes

11 En

Connections

English

USB port

This unit has a USB port and can access MP3,

WMA, DivX and JPEG files saved on your

USB device.

Connect the USB port on the front panel of

this unit to a USB port of your USB device.

• This unit may not recognize some USB devices.

• For details about the USB features, see “Using a

USB device” on page 21.

Remote control jacks

This unit has remote control input/output

jacks. If your AV receiver is a Yamaha product

and has the capability to transmit of SCENE

control signals, you can use the SCENE

function.

Connect the REMOTE CONTROL (IN) jack

of this unit to a remote control output jack of

your receiver using a commercially available

monaural mini-jack cable so that this unit

starts playback automatically by simply

pressing a button of your receiver.

For details about the SCENE function, refer to the

owner’s manual supplied with your Yamaha AV

receiver.

Other connections

Notes

This unit

USB

device

Note

REMOTE CONTROL

OUT

HDMI

IN

REMOTE OUT

This unit

AV receiver

12 En

Getting Started

1 Open the battery compartment.

2 Insert the two supplied batteries (AAA,

R03, UM-4) following the indications

(+/–) inside the compartment.

3 Close the cover.

• Insert batteries correctly according to the polarity

markings (+/–). Batteries inserted in the opposite

orientation may leak.

• Replace the exhausted batteries immediately with

new ones to prevent leakage.

• Remove the batteries from the compartment if the

remote control is not used for more than a month.

• If the batteries have leaked, dispose of them

immediately. Avoid touching the leaked material

or letting it come into contact with clothing, etc.

Clean the battery compartment thoroughly before

installing new batteries.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as

alkaline and manganese batteries) together. Read

the packaging carefully as these different types of

batteries may have the same shape and color.

• Dispose of the batteries correctly in accordance

with your local regulations.

Using the remote control

Use the remote control within 6 m of this unit

and point it toward the remote control sensor.

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– places of high humidity, such as near a bath

– places of high temperature, such as near a

heater or stove

– places of extremely low temperature

– dusty places

• When the remote control works unstably, point it

at an angle upward to the sensor.

1 Plug the power cable into the AC outlet.

2 Turn on your TV and AV receiver.

3 Select the appropriate input source of the

AV receiver (refer to the manual supplied

with your AV receiver).

4 Press STANDBY/ON on the front panel or

on the remote control to turn on this

unit.

➜ The front panel display lights up.

5 Set the TV to the correct video input (refer

to the manual supplied with your TV).

➜ The default screen appears on the TV.

Step 1: Inserting batteries into

the remote control

Notes

2

1

3

2

Notes

Step 2: Turning on the power

Within 6 m

Getting Started

13 En

Getting Started

English

You can customize this unit using the setup

menu displayed on the TV screen.

• Unless stated otherwise, all operations described

here are carried out using the supplied remote

control.

• To return to the previous menu, press 2 .

• To exit from the menu, press SET UP.

Setting a color system for your TV

This unit is compatible with both NTSC and

PAL video formats. Select the color system

that matches your TV.

1 Press SET UP.

2 Press 3 repeatedly to select “VIDEO

SETUP PAGE”.

3 Press 5 /a to highlight [TV TYPE], and

then press 3.

4 Press 5 /a to highlight one of the

following options.

PAL

Select this if the connected TV is a PAL

system TV. It will change the video signals of

NTSC discs and output them in PAL format.

NTSC

Select this if the connected TV is an NTSC

system TV. It will change the video signals of

PAL discs and output them in NTSC format.

MULTI

Select this if the connected TV is compatible

with both NTSC and PAL formats (such as a

multi-system TV).

The output format will be in accordance with

the video signals of the disc.

5 Select an item, and then press ENTER.

• Before changing the current TV standard setting,

ensure that your TV supports the selected TV

type.

• If the picture is not displayed properly on your

TV, wait for 15 seconds for this unit to activate

automatic recovery.

• When making HDMI connections, you cannot

change or select [TV TYPE].

Setting an aspect ratio for your TV

You can set the aspect ratio of this unit to

match your TV. If the aspect ratio of your TV

is 4:3, you do not need to change this setting.

If you have a widescreen TV, change this

setting according to the procedure below.

For details, see “Setting the TV display” on

page 27.

Step 3: Setting a TV type/display

and language

Notes

VIDEO SETUP PAGE

TV TYPE PAL

TV DISPLAY NTSC

PROGRESSIVE MULTI

PICTURE SETTING

HDMI SETUP

Notes

CHANGING PAL TO NTSC :

1. ENSURE THAT YOUR TV SUPPORTS

NTSC STANDARD.

2. IF THERE IS A DISTORTED PICTURE

DISPLAYED ON THE TV, WAIT 15

SECONDS FOR AUTO RECOVER.

OK CANCEL

14 En

Getting Started

1 Press SET UP.

2 Press 3 repeatedly to select “VIDEO

SETUP PAGE”.

3 Press 5 /a to highlight [TV DISPLAY],

and then press 3.

4 Press 5 /a to highlight [16:9], and then

press ENTER.

Setting the OSD Language

You can select your own preferred language

for the setup menu. This setting remains once

selected.

1 Press SET UP.

2 Press 2 / 3 to select “GENERAL SETUP

PAGE”.

3 Press 5 /a to highlight [OSD

LANGUAGE], and then press 3.

4 Press 5 /a to select a language, and then

press ENTER.

Setting the audio, subtitle and disc

menu languages (DVD-Video only)

You can select your own preferred language

for the audio, subtitle and disc menu. This unit

automatically switches to the selected

language whenever you load a disc. If the

selected language is not available on the disc,

the default language of the disc will be used

instead.

1 Press

7

twice, and then press SET UP.

2 Press 3 repeatedly to select

“PREFERENCE PAGE”.

3 Press 5/a to highlight one of the options

below, and then press 3 .

• AUDIO (audio language)

• SUBTITLE (subtitle language)

• DISC MENU (disc menu language)

4 Press 5/a to select a language, and then

press ENTER.

5 Repeat steps 3-4 for other language

settings.

■ To select a language not in the list

1 Select [OTHERS] in [AUDIO] or

[SUBTITLE] or [DISC MENU].

2 Use the numeric buttons (0-9) to enter

the 4-digit language code (see “Language

Codes” on page 33), and then press

ENTER.

VIDEO SETUP PAGE

TV TYPE

TV DISPLAY 4:3 PAN SCAN

PROGRESSIVE 4:3 LETTER BOX

PICTURE SETTING 16:9

HDMI SETUP

GENERAL SETUP PAGE

DISC LOCK

DISPLAY DIM

PROGRAM

OSD LANGUAGE ENGLISH

SCREEN SAVER

SLEEP

AUTO STANDBY

DIVX(R) VOD CODE

PREFERENCE PAGE

AUDIO ENGLISH

SUBTITLE CHINESE (SIMP)

DISC MENU FRENCH

PARENTAL SPANISH

VR LIST PORTUGUESE

MP3/JPEG NAV POLISH

DIVX SUBTITLE ITALIAN

PBC TURKISH

15 En

Playback Operation

English

• If the prohibited icon ( ) appears on the TV

screen when a button is pressed, the function for

that button is not available on the current disc or

at the current time.

• Unless stated otherwise, all operations described

here are carried out using the supplied remote

control.

• Depending on the disc, some operations may

operate differently or be restricted. Refer to the

instruction supplied with the disc.

• Do not push on the disc tray or put any objects

other than discs on the disc tray. Doing so may

cause this unit to malfunction.

1 Make sure this unit is turned on.

2 Press OPEN/CLOSE ( ) on the front

panel to open the disc tray.

3 Place the disc in the disc tray with the

printed side up.

4 Press OPEN/CLOSE ( ) again to close

the disc tray.

➜ After recognizing the disc, this unit

starts playback automatically.

• If you press 3

/ 8 when the disc tray is

open, the disc tray closes and playback

starts automatically.

5 To pause playback, press 3 / 8 during

playback.

➜ Playback is paused and the sound is

muted.

• Frame-by-frame playback can be done

by pressing PAUSE (

  ) on the front

panel repeatedly.

6 To resume normal playback, press 3 / 8

again.

7 To stop playback, press

7

.

Selecting a track/chapter

1 Press l22 / 33l or use the numeric

buttons (0-9) to select a track/chapter

number.

2 During repeated playback, press l22 /

33l to replay the same track/chapter.

Searching backward/forward

1

Press and hold l22 / 33l or press 2 / 3.

2 While searching, press l22 / 33l or

2 / 3 repeatedly to select the desired

speed.

3 To resume normal playback, press 3 / 8 .

•The 2 / 3 key may not be available with some

discs.

• For MP3 and WMA, the search function allows

you to search the track currently being played.

Repeat/Shuffle playback

Each time you press REPEAT during

playback, the front panel display changes

as follows:

DVD

➜ RPT ONE (repeat chapter)

➜ RPT TT (repeat title)

➜ RPT ALL (repeat all)

➜ SHUFFLE (shuffle)

➜ RPT SHF (shuffle repeat)

➜ RPT OFF (repeat off)

VCD/SVCD/CD

➜ RPT ONE (repeat track)

➜ RPT ALL (repeat all)

➜ SHUFFLE (shuffle)

➜ RPT SHF (shuffle repeat)

➜ RPT OFF (repeat off)

Notes

Basic operation

Notes

Repeat/Shuffle functions

Playback Operation

16 En

Playback Operation

MP3/WMA/DivX

➜ RPT ONE (repeat track)

➜ RPT FLD (repeat folder)

➜ SHUFFLE (shuffle)

➜ RPT OFF (repeat off)

For VCD, repeat playback is not available when the

PBC mode is on.

Repeating a section within a

chapter/track

1

While playing a disc, press REPEAT A-B

at the desired starting point.

➜ “SET A” appears in the front panel

display.

2 Press REPEAT A-B again at the desired

end point.

• A and B can only be set within the same

chapter/track.

➜ “RPT AB” appears in the front panel

display and the selected section repeats

continuously.

3 To exit from the sequence, press REPEAT

A-B.

Using the disc menu

Depending on the disc, a menu may appear on

the TV screen once you load the disc.

■ To select a playback feature or item

Use 2 / 3 /5 /a or the numeric

buttons (0-9), and then press ENTER to

start playback.

■ To access or exit from the menu

Press MENU.

Playback in slow motion

You can play back video in slow motion.

1 Press 5 for reverse slow motion or a for

forward slow motion.

2 During slow motion, press 5/a repeatedly

to select the desired speed.

3 To resume normal playback, press 3 / 8 or

ENTER.

For VCD and SVCD, reverse slow motion is not

available.

Zooming pictures in/out

You can enlarge or shrink the picture on the

TV screen and pan through the enlarged

picture.

1 During playback, press ZOOM repeatedly

to display the picture at different scales.

•Use 2 / 3 /5 /a to pan through the

enlarged picture.

➜ Playback continues.

2 Press ZOOM repeatedly to return to the

original size.

Resuming playback from the last

stopped point

You can resume playback of the last ten discs,

even if the discs were ejected or the power of

this unit was turned off.

1 Load one of the last ten discs.

➜ “LOADING” appears on the TV

screen.

2 Press 3 / 8 while “LOADING” is

displayed on the TV screen.

➜ “RESUME PLAY” appears on the TV

screen and the disc is played back from

the last point.

■ To cancel the resume mode

When playback is stopped, press

7

again.

Note

Operations for video playback

(DVD/VCD/SVCD)

Note

17 En

Playback Operation

English

Using the on-screen display (OSD)

The OSD menu shows disc playback

information (e.g., the title or chapter number,

elapsed playing time or audio/subtitle

language). A number of operations are

possible without interrupting disc playback.

1 During playback, press ON SCREEN.

➜ A list of available disc information

appears on the TV screen.

DVD

VCD/SVCD

2 Press 5 /a to scroll the information, and

then press ENTER to access the selected

item.

3 Use the numeric buttons (0-9) to input

the number/time or press 5 /a to make a

selection, and then press ENTER.

➜ Playback changes to the selected time

or to the selected title/chapter/track.

■ Title/Chapter/Track selection

(DVD/VCD)

1 Press 5/a to select [TITLE] or

[CHAPTER] (DVD) or [TRACK] (VCD).

2 Press ENTER.

3 Select a title, chapter or track number using

the numeric buttons (0-9).

■ Time search (DVD/VCD)

1 Press 5/a to select [TT TIME] / [CH

TIME] (DVD) or [TRACK TIME] / [DISC

TIME] (VCD).

• [TT TIME] refers to the total time of

the current title, and [CH TIME] refers

to the total time of the current chapter.

2 Press ENTER.

3 Enter hours, minutes and seconds from left

to right using the numeric buttons (0-9)

(e.g. 0:34:27).

■ Audio/Subtitle/Angle selection

(DVD)

You can change [AUDIO], [SUBTITLE] or

[ANGLE] if these functions are available on

the disc you are playing.

1 Press 5/a to select [AUDIO],

[SUBTITLE] or [ANGLE].

2 Press ENTER.

3 For Audio and Subtitle:

Press 5 /a to highlight your selection, and

then press ENTER.

OR

For Angle:

Select an angle using the numeric

buttons (0-9).

MENU

TITLE 02/14

CHAPTER 02/14

AUDIO 5.1CH

SUBTITLE ENG

BITRATE 16 TITLE ELAPSED 0:02:25

MENU

TRACK 02/14

DISC TIME 0:49:17

TRACK TIME 0:03:43

REPEAT OFF

BITRATE 16 TOTAL ELAPSED 0:02:25

18 En

Playback Operation

■ Repeat/Time Display (DVD/VCD)

1 Press 5 /a to select [REPEAT] or [TIME

DISP.].

2 Press ENTER.

3 Press 5/a to highlight your selection, and

then press ENTER.

■ Time display (CD)

Each time you press ON SCREEN, the

time display changes as follows:

Playing by title

1

Press MENU.

➜ The disc title menu appears on the TV

screen.

2 Use 2 / 3 /5 /a or the numeric

buttons (0-9) to select a playback option.

3 Press ENTER.

Selecting an audio language/

format and subtitle language

■ To select an audio language/format

Press AUDIO repeatedly to select an audio

language and/or format.

■ To select a subtitle language

Press SUBTITLE repeatedly to select a

subtitle language.

Using the playback control (PBC)

menu

For a VCD with a playback control (PBC)

feature (version 2.0 only)

1 Press MENU to toggle between “PBC ON”

and “PBC OFF”.

➜ If you select “PBC ON”, the disc menu

appears (if available) on the TV screen.

2 Use the numeric buttons (0-9) to select

a playback option.

• Press l22 / 33l to move to the

previous/next page (if available).

3 During playback, press TOP MENU/

RETURN to return to the menu screen.

■ To skip the index menu and play

back a disc from the beginning

Press MENU to turn off the PBC function.

1 Load a data disc.

• The disc reading time may exceed 30

seconds due to the complexity of the

directory/file configuration.

➜ The data disc menu appears on the TV

screen.

Special DVD features

TOTAL ELAPSED TOTAL REMAIN

SINGLE REMAIN SINGLE ELAPSED

Special VCD/SVCD features

Playing data discs

(MP3/WMA/JPEG/DivX)

00:00 00:00

001/020

Piano

Cello

Jazz

Live

Favorite

MP3

ページが読み込まれています...

Yamaha DVD-S661 取扱説明書

Yamaha DVD-S661 取扱説明書

他の言語で

関連論文

その他のドキュメント