Yamaha P-255 取扱説明書

Manual de instrucciones

Mode d'emploi

Owner’s Manual

Before using the instrument, be sure to read “PRECAUTIONS” on pages 4–5.

Avant d’utiliser l’instrument, lisez attentivement la section « PRÉCAUTIONS D'USAGE » aux pages 4 et 5.

Antes de utilizar el instrumento, lea las “PRECAUCIONES”, en las páginas 4–5.

255

PIANO NUMÉRIQUE

DIGITAL PIANO

PIANO DIGITAL

ENGLISHFRANÇAIS

ESPAÑOL

P-255 Owner’s Manual

SPECIAL MESSAGE SECTION

This product utilizes batteries or an external power supply (adapter). DO

NOT connect this product to any power supply or adapter other than one

described in the manual, on the name plate, or specifically recom-

mended by Yamaha.

WARNING: Do not place this product in a position where anyone

could walk on, trip over, or roll anything over power or connecting cords

of any kind. The use of an extension cord is not recommended! If you

must use an extension cord, the minimum wire size for a 25’ cord (or

less ) is 18 AWG. NOTE: The smaller the AWG number, the larger the

current handling capacity. For longer extension cords, consult a local

electrician.

This product should be used only with the components supplied or; a

cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is

used, please observe all safety markings and instructions that accom-

pany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at the

time of printing. However, Yamaha reserves the right to change or mod-

ify any of the specifications without notice or obligation to update existing

units.

This product, either alone or in combination with an amplifier and head-

phones or speaker/s, may be capable of producing sound levels that

could cause permanent hearing loss. DO NOT operate for long periods

of time at a high volume level or at a level that is uncomfortable. If you

experience any hearing loss or ringing in the ears, you should consult an

audiologist.

IMPORTANT: The louder the sound, the shorter the time period before

damage occurs.

Some Yamaha products may have benches and / or accessory mount-

ing fixtures that are either supplied with the product or as optional

accessories. Some of these items are designed to be dealer assembled

or installed. Please make sure that benches are stable and any optional

fixtures (where applicable) are well secured BEFORE using.

Benches supplied by Yamaha are designed for seating only. No other

uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how a

function or effect works (when the unit is operating as designed) are not

covered by the manufacturer’s warranty, and are therefore the owners

responsibility. Please study this manual carefully and consult your dealer

before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and environ-

mentally friendly. We sincerely believe that our products and the produc-

tion methods used to produce them, meet these goals. In keeping with

both the letter and the spirit of the law, we want you to be aware of the

following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if

applicable) is soldered in place. The average life span of this type of bat-

tery is approximately five years. When replacement becomes necessary,

contact a qualified service representative to perform the replacement.

This product may also use “household” type batteries. Some of these

may be rechargeable. Make sure that the battery being charged is a

rechargeable type and that the charger is intended for the battery being

charged.

When installing batteries, never mix old batteries with new ones, and

never mix different types of batteries. Batteries MUST be installed cor-

rectly. Mismatches or incorrect installation may result in overheating and

battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all batter-

ies away from children. Dispose of used batteries promptly and as regu-

lated by the laws in your area. Note: Check with any retailer of

household type batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some reason

its useful life is considered to be at an end, please observe all local,

state, and federal regulations that relate to the disposal of products that

contain lead, batteries, plastics, etc. If your dealer is unable to assist

you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model num-

ber, serial number, power requirements, etc., are located on this plate.

You should record the model number, serial number, and the date of pur-

chase in the spaces provided below and retain this manual as a perma-

nent record of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

92-BP (bottom)

P-255 Owner’s Manual

Contents

PRECAUTIONS .....................................................4

P-255 Manuals.......................................................6

Included Accessories .............................................6

Main Features 7

Panel Controls & Functions 8

Getting Ready

Setting Up 10

Turning on the instrument ......................................10

Auto Power-Off.......................................................10

Adjusting the volume..............................................11

Setting up the music rest........................................11

Using headphones .................................................11

Connecting pedals (Sustain pedal) ........................11

Using an optional pedal unit...................................12

Main Operations

Selecting & Playing Voices 13

Selecting Voices.....................................................13

Listening to the Voice demo songs ........................13

Layering two Voices with Dual mode .....................14

Dividing the keyboard with Split mode ...................14

Adding reverb.........................................................15

Adding effects ........................................................16

Transposing ...........................................................16

Tuning the instrument ............................................17

Changing the touch sensitivity ...............................17

Adjusting the tone ..................................................17

Boosting the overall sound.....................................18

Locking the control panel .......................................18

Using the Metronome 19

Playing Rhythm Tracks 20

Playing Songs 21

Supported song types ............................................21

Playing a song........................................................21

Convenient playback functions ..............................23

Recording Keyboard Performances 25

Simple recording of all parts (MIDI or Audio

songs)................................................................25

Recording individual parts (MIDI songs) ................27

Deleting recorded parts individually (MIDI songs)..28

Changing Voice(s) and tempo, etc. after recording

(MIDI songs) ......................................................28

Using USB Flash Drives 30

Working with USB flash drives............................... 30

Managing files on a USB flash drive...................... 31

Copying a User Song recorded on the instrument

to a USB flash drive .......................................... 32

Deleting a User Song............................................. 33

Formatting a USB flash drive................................. 33

Connecting Other Equipment 34

Connecting audio equipment ................................. 34

Connecting to a computer...................................... 34

Connecting other MIDI devices.............................. 35

Connecting an iPad or iPhone............................... 35

Performing Live 36

Performing on-stage as part of a band .................. 36

Singing and playing on your own........................... 38

Customizing with Function Parameters 40

Basic Function-parameter operations.................... 41

Descriptions of Function parameters..................... 41

Restoring factory settings ...................................... 48

Appendix

Display Messages ............................................... 49

Troubleshooting .................................................. 50

Voice List............................................................. 51

50 Piano Songs (Preset Songs).......................... 52

Specifications ...................................................... 53

Index ................................................................... 54

P-255 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-

circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or radiators. Also, do not

excessively bend or otherwise damage the cord, or place heavy objects on it.

• Only use the voltage specified as correct for the instrument. The required voltage is printed on

the name plate of the instrument.

• Use the specified adaptor (page 53) only. Using the wrong adaptor can result in damage to the

instrument or overheating.

• Check the electric plug periodically and remove any dirt or dust which may have accumulated

on it.

• This instrument contains no user-serviceable parts. Do not open the instrument or attempt to

disassemble or modify the internal components in any way. If it should appear to be

malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service

personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet conditions, place on it

any containers (such as vases, bottles or glasses) containing liquids which might spill into any

openings. If any liquid such as water seeps into the instrument, turn off the power immediately

and unplug the power cord from the AC outlet. Then have the instrument inspected by qualified

Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning item may fall over and cause

a fire.

• When one of the following problems occur, immediately turn off the power switch and

disconnect the electric plug from the outlet. Then have the device inspected by Yamaha service

personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the instrument.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument

or other property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a multiple-connector. Doing so can

result in lower sound quality, or possibly cause overheating in the outlet.

• When removing the electric plug from the instrument or an outlet, always hold the plug itself

and not the cord. Pulling by the cord can damage it.

• Remove the electric plug from the outlet when the instrument is not to be used for extended

periods of time, or during electrical storms.

• Do not place the instrument in an unstable position where it might accidentally fall over.

• Before moving the instrument, remove all connected cables, to prevent damage to the cables or

injury to anyone who might trip over them.

• When setting up the product, make sure that the AC outlet you are using is easily accessible. If

some trouble or malfunction occurs, immediately turn off the power switch and disconnect the

plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the

product at the minimum level. When you are not using the product for a long time, make sure to

unplug the power cord from the wall AC outlet.

• Use only the specified for the instrument. When attaching the stand or rack, use the provided

screws only. Failure to do so could cause damage to the internal components or result in the

instrument falling over.

• Before connecting the instrument to other electronic components, turn off the power for all

components. Before turning the power on or off for all components, set all volume levels to

minimum.

• Be sure to set the volumes of all components at their minimum levels and gradually raise the

volume controls while playing the instrument to set the desired listening level.

• Do not insert a finger or hand in any gaps on the instrument.

• Never insert or drop paper, metallic, or other objects into the gaps on the panel or keyboard.

This could cause physical injury to you or others, damage to the instrument or other property,

or operational failure.

• Do not rest your weight on, or place heavy objects on the instrument, and do not use excessive

force on the buttons, switches or connectors.

• Do not use the instrument/device or headphones for a long period of time at a high or

uncomfortable volume level, since this can cause permanent hearing loss. If you experience

any hearing loss or ringing in the ears, consult a physician.

Always turn the power off when the instrument is not in use.

Even when the [ ] (Standby/On) switch is in standby status (display is off), electricity is still flowing to the instrument at the minimum level.

When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet.

Power supply/AC power adaptor

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/AC power adaptor

Location

Connections

Handling caution

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.

DMI-5 1/1

P-255 Owner’s Manual

Notice

To avoid the possibility of malfunction/ damage to the product, damage to

data, or damage to other property, follow the notices below.

 Handling and Maintenance

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or

other electric devices. Otherwise, the instrument, TV, or radio may generate noise.When you use

the instrument along with an application on your iPad, iPhone or iPod touch, we recommend

that you set “Airplane Mode” to “ON” on that device in order to avoid noise caused by

communication.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as

in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel

disfiguration, damage to the internal components or unstable operation. (Verified operating

temperature range: 5° – 40°C, or 41° – 104°F.)

• Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the

panel or keyboard.

• When cleaning the instrument, use a soft, dry or slightly damp cloth. Do not use paint thinners,

solvents, cleaning fluids, or chemical-impregnated wiping cloths.

 Saving data

• Saved data may be lost due to malfunction or incorrect operation. Save important data to a USB

flash memory/external device such as a computer.

• To protect against data loss through media damage, we recommend that you save your

important data onto two USB flash memories.

Information

 About copyrights

• Copying of the commercially available musical data including but not limited to MIDI data and/

or audio data is strictly prohibited except for your personal use.

• This product incorporates and bundles computer programs and contents in which Yamaha owns

copyrights or with respect to which it has license to use others’ copyrights. Such copyrighted

materials include, without limitation, all computer software, style files, MIDI files, WAVE data,

musical scores and sound recordings. Any unauthorized use of such programs and contents

outside of personal use is not permitted under relevant laws. Any violation of copyright has

legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.

 About functions/data bundled with the instrument

• Some of the preset songs have been edited for length or arrangement, and may not be exactly

the same as the original.

 About this manual

• The illustrations and displays as shown in this manual are for instructional purposes only, and

may appear somewhat different from those on your instrument.

• Apple, Mac, Macintosh, iPad, iPhone and iPod touch are trademarks of Apple Inc., registered in

the U.S. and other countries.

• The company names and product names in this manual are the trademarks or registered

trademarks of their respective companies.

P-255 Owner’s Manual

Thank you for purchasing the Yamaha P-255 Digital Piano. We recommend that you read this Owner’s

Manual carefully in order to get the most out of the instrument’s advanced functionality. In addition,

please keep this manual in a safe place so that you can refer back to it whenever needed.

P-255 Manuals

The following manuals have been prepared for your digital piano.

Hardcopy format

Owner’s Manual (this booklet)

This manual describes how to use the P-

255.

Digital format (pdf)

iPhone/iPad Connection Manual

This manual describes how to connect

your digital piano to smart devices such

as an iPad or iPhone.

Computer-related Operations

This manual describes how to connect

your digital piano and a computer.

MIDI Reference

This manual contains the instrument’s

MIDI Data Format and MIDI Implemen-

tation Chart.

MIDI Basics

This manual provides a description of the

basic features of MIDI.

The digital-format manuals listed above can be

obtained from the Yamaha Downloads web page.

To do so, go to the Downloads page using the URL

provided below, enter “P-255” into the Model

Name field, and then click Search.

Yamaha Downloads

http://download.yamaha.com/

Included Accessories

 Owner’s Manual (this book)

 Online Member Product Registration

 AC Power Adaptor

 Footswitch

 Music Rest

*1 You will need the PRODUCT ID on the sheet in order to fill out the User Registration form.

*2 May not be included depending on your particular area. Please check with your Yamaha dealer.

P-255 Owner’s Manual

Main Features

Exquisite sound of a concert grand piano faithfully reproduced by the Pure CF Sound Engine

In order to give the P-255 the best possible piano sound, we started by selecting the one Yamaha

concert grand piano with the highest quality tone and acoustic properties. Expert tuners then pains-

takingly ensured that the selected piano was perfectly pitched, and finally, our Pure CF Sound

Engine technology was employed to meticulously sample the full lifespan of every single note.

Graded Hammer keyboard with synthetic ivory keytops for an authentic feel

Developed with the aim of reproducing the sensation of playing a real grand piano, the Graded

Hammer (GH) keyboard features naturally weighted keys, with those in the low range feeling

heavier than those in the high range. As a result, the keyboard feels perfectly balanced over its

complete length. What’s more, the synthetic ivory finish applied to the white keys has excellent

moisture absorption characteristics, meaning that you can play in comfort for as long as you want

without fear of the keys becoming slippery.

Ten different rhythm tracks built in

Playing the keyboard along with one of the ten basic rhythm tracks built into your P-255 is a great

way to add spice to your performances, and as such, these automatic rhythms make playing more

fun. Featuring a range of different patterns from jazz, popular music, and the like, the digital

piano’s rhythm tracks are sure to include what you are looking for.

Live Music Toolbox for performing on-stage

Collectively known as the Live Music Toolbox, the P-255 features a number of functions that

come in handy when performing on stage. For example, you can use Sound Boost to make the

instrument sound louder and enhance its presence (page 18), and the Panel Lock function deacti-

vates buttons on the control panel so you won’t have to worry about pressing them by mistake

while playing (page 18). Meanwhile, you can also turn off the built-in speakers when alternatives

are provided on-stage (page 44). With these tools at your disposal, it is easier to set up your digital

piano on-stage and performing becomes much more enjoyable.

Operate the instrument using P-255 Controller on your iPad, iPhone, or iPod

With the specially developed app P-255 Controller running on your iPad, iPhone, or iPod, you can

remotely control your digital piano for even more convenience and flexibility. By presenting vari-

ous parameters on-screen, this app allows you to make settings in a visual, more intuitive manner.

More details can be found on the following web site.

http://www.yamaha.com/kbdapps/

P-255 Owner’s Manual

Panel Controls & Functions

q [ ] Standby/On switch...................................Page 10

Use this switch to turn the instrument on or set it to

Standby mode.

w [MASTER VOLUME] slider ...............................Page 11

Use this slider to adjust the instrument’s overall volume.

e [DEMO] button ..................................................Page 13

Use this button to play demo tracks for individual Voices.

r [TRANSPOSE] button.......................................Page 16

Use this button to shift the pitch of the entire keyboard up

or down. This allows you to match your playing to the key

of another instrument or a singer without having to

change what you actually play on the keyboard.

t [SELECT] button ..............................................Page 21

Use this button to select the category of song you wish to

play back.

y [REC] button .....................................................Page 25

Use this button to record what you play on the keyboard.

u [PLAY/STOP] button ........................................Page 22

Use this button to start and stop playback of Piano

Songs (50 included), recordings of your own perfor-

mances, or songs stored on a USB flash drive.

i [LEFT] and [RIGHT] buttons ............................Page 23

Use these buttons to turn playback of the left-hand and

right-hand parts on or off. This allows you to practice

playing the parts that have been turned off.

o [TEMPO] button ................................. Pages 19, 20, 22

Use this button to adjust the instrument’s tempo.

!0 [METRONOME] button .................................... Page 19

Use this button to turn the metronome on and off.

!1 [RHYTHM] button ............................................ Page 20

Use this button to turn rhythm tracks on and off.

!2 Display ............................................................. Page 10

The display shows the current tempo when the digital

piano is turned on. Following this, it shows useful infor-

mation relevant to the operation you are performing at

the time.

!3 [FUNCTION] button ........................................ Page 40

Use this button to access other highly convenient func-

tions.

!4 [-/NO] and [+/YES] buttons

Use these buttons when setting values and selecting

songs or other display items. Certain settings, such as

Transpose and Tempo, can be reset to their default val-

ues by pressing both buttons simultaneously.

!5 Voice buttons.................................................... Page 13

Use these buttons to select various Voices.

• Dashes (“-”) will scroll across the display while the

instrument is accessing data. Do not turn off the instru-

ment at this time. Failure to observe this precaution may

cause the data to be corrupted.

NOTICE

w e r t y u i o !0 !1

Panel Controls & Functions

P-255 Owner’s Manual

!6 [SPLIT] button ...................................................Page 14

Use this button to assign different Voices to the left-hand

and right-hand sides of the keyboard.

!7 [REVERB] and [EFFECT] buttons ..........Pages 15, 16

Use these buttons to apply reverb and other effects to

the sound produced by the digital piano.

!8 [SOUND BOOST] button ..................................Page 18

Use this button to make the instrument sound louder and

enhance its presence in live performance situations.

!9 [EQ] (Equalizer) sliders ...................................Page 17

Use the Low, Mid, and High sliders to adjust the tone of

the sound produced by the instrument in the correspond-

ing frequency ranges.

@0 [PHONES] jacks ............................................... Page 11

Use each of these audio jacks to connect a pair of stereo

headphones.

@1 [USB TO DEVICE] terminal ..............................Page 30

Use this terminal to connect a USB flash drive to your

digital piano. You can then save your recorded songs on

the flash drive and play back songs stored on it.

@2 [AUX IN] jack .....................................................Page 34

Stereo output from another instrument or audio device

can be input via this jack and output from the digital

piano’s speakers together with its own sound.

In addition, it can also be output via the [PHONES] jacks

(@0) and the AUX OUT jacks (@3).

@3 [L/L+R] and [R] AUX OUT jacks .....................Page 34

Use these jacks to connect your digital piano to powered

speakers and the like in order to play at higher volumes.

@4 [SUSTAIN PEDAL] jack ................................... Page 11

Use this jack to connect the foot switch that came with

your digital piano or an optional foot switch or pedal (sold

separately).

@5 [IN] and [OUT] MIDI terminals ........................ Page 35

Use these terminals to connect the instrument to other

devices in order to exchange data via MIDI.

@6 [USB TO HOST] terminal.......................... Pages 34, 35

Use this terminal to connect the instrument to an iPhone,

iPad, or computer.

@7 [PEDAL UNIT] terminal ................................... Page 12

Use this terminal to connect an optional pedal unit (sold

separately).

@8 [DC IN] jack ....................................................... Page 10

Use this jack to connect the power adaptor that came

with your digital piano.

!2 !3 !4 !5 !6

!7 !8

@2 @3 @4 @5 @6

P-255 Owner’s Manual

Setting Up

Plug the appliance end of the AC power cord into

the bundled power adaptor as shown in the figure.

Plug the power adaptor’s DC cable into the [DC IN]

jack on the rear panel.

Plug the power adaptor’s AC power cord into a

domestic-use, AC wall socket.

Press the [ ] Standby/On switch.

The digital piano will turn on and the display at

the center of the control panel will light up.

To turn off the instrument, press the [ ] Standby/

On switch once again.

The Auto Power-Off function automatically turns off

your digital piano after a set period of inactivity in order

to save power. By default, it will turn off the instrument

after 30 minutes if it is not operated in any way.

Disabling the Auto Power-Off function

To disable the Auto Power-Off function, either set the

corresponding Function parameter to “Off” or turn on

the instrument while holding down the left-most key

on the keyboard. When disabled in this way, the

instrument will not turn off automatically.

Changing the Auto Power-Off time

Press the [FUNCTION] button to access the Func-

tion parameters.

Press the [FUNCTION] button repeatedly until Func-

tion parameter

F8.8

is shown. Then, press the [-/NO]

or [+/YES] button to select that Function parameter.

Set the desired Auto Power-Off time using the [-/NO]

and [+/YES] buttons.

• Available settings: OFF, 5, 10, 15, 30, 60, and 120 minutes

• Default setting: 30 minutes

Press the [FUNCTION] button to return to the previ-

ous screen.

Turning on the instrument

• Be sure to use only the correct power adaptor (page

53). Other adaptors may damage the instrument, cause

it to overheat, or create a fire hazard.

• Be sure to use a power supply at the correct voltage.

• Be sure to unplug the power adaptor from the AC wall

socket during electrical storms or if the instrument is

not to be used for an extended period of time.

• The digital piano remains charged and draws a small

amount of power even when turned off. Be sure, therefore,

to unplug the power adaptor from the AC wall socket if it

is not to be used for an extended period of time.

• Carry out the above procedure in reverse when disconnecting the power adaptor.

If you are going to use your instrument in a live

music situation such as on-stage, please read

the section Performing Live (page 36).

[DC IN] jack

AC wall socket

The shape of the plug and outlet

differ depending on locale.

WARNING

CAUTION

120

Normally shows the

current tempo.

[] Standby/On switch

Display

CAUTION

NOTE

Auto Power-Off

• Before the Auto Power-Off function turns off the instrument, unsaved data

will be automatically backed up. See page 46 for details of the data backed

up at this time.

• In certain modes of operation, the Auto Power-Off func-

tion will not turn off the digital piano when the set time

has elapsed. We recommend, therefore, that you

always turn off the instrument manually when you are

finished using it.

• If your digital piano is connected to other equipment

such as amplifiers, speakers, or a computer but you do

not intend to use it for some time, we recommend that

you turn off all devices as described in their owner’s

manuals. Doing so eliminates the risk of damage to the

other equipment. If you do not want the instrument to

turn off automatically when connected to other equip-

ment, disable the Auto Power-Off function.

If you are going to use your instrument in a live music

situation such as on-stage, we recommend that you

disable the Auto Power-Off function. (See page 37, 39.)

Left-most key

NOTE

NOTICE

Getting Ready

Setting Up

P-255 Owner’s Manual

To adjust the volume, use the [MASTER VOLUME]

slider at the left of the control panel while playing the

keyboard to check the setting.

To set up the music rest, insert it into the groove at the

back of the control panel.

Your digital piano features two [PHONES] jacks,

allowing two sets of headphones to be connected at

the same time. If you wish to connect only one set,

either of the jacks can be used. No sound will be out-

put from the instrument’s speakers when headphones

are connected to either or both of the jacks.

When plugged into the [SUSTAIN PEDAL] jack, the

FC4 Foot Switch that came with your digital piano

functions in the same way as the damper pedal of an

acoustic piano—that is, it allows notes played while it

is operated to sustain for longer than normal after you

release the corresponding keys. You can also connect

either an FC3 Foot Pedal or an FC5 Foot Switch (sold

separately). The FC3 supports half-damper playing.

Half-damper playing

Your digital piano can adjust the length of sustain in

response to how much the pedal is operated. In spe-

cific terms, the more the pedal is operated, the longer

the notes sustain. If, for example, too much sustain is

applied when you operate the pedal, reduce the level

(and make the sound clearer) by allowing the pedal to

return slightly.

Adjusting the volume

Setting up the music rest

Using headphones

• To prevent hearing loss, avoid using headphones at high

volumes for extended periods of time.

LouderQuieter

Front panel

Standard stereo-

phone plug

CAUTION

Connecting pedals (Sustain pedal)

• Do not turn on the instrument with a foot switch or pedal operated. Failure to

observe this precaution can cause the on and off positions of the switch or pedal

to be reversed.

• Be sure to turn off the digital piano before connecting or disconnecting a foot

switch or pedal.

FC4

NOTE

Setting Up

P-255 Owner’s Manual

An LP-255 Pedal Unit (sold separately) can be con-

nected if you wish to play the digital piano using a full

set of three pedals. In such a case, please set up the

instrument and pedal unit on an L-255 Keyboard

Stand (sold separately).

Damper pedal

Located at the right of the pedal unit, the damper

pedal allows notes played while it is operated to sus-

tain for longer than normal after you release the corre-

sponding keys. This pedal supports half-damper

playing—the more you operate it, the longer the notes

sustain.

Damper-pedal resonance

Yo ur digital piano’s damper resonance function recreates the

effect of resonance between individual piano strings when

the damper pedal is operated. The depth of this resonance

can be set using the corresponding Function parameter

(page 40).

Sostenuto pedal

The pedal located at the middle of the pedal unit is

known as the sostenuto pedal. If you play a note or

chord on the keyboard and operate this pedal before

releasing the keys, the corresponding notes will sus-

tain until you allow the pedal to return. Notes played

while the pedal is operated are not affected, meaning

that you can play a staccato melody over a sustained

chord.

Soft pedal

Located at the left of the pedal unit, the soft pedal

slightly lowers the volume and softens the timbre of

notes played while it is being operated. This effect

lasts until the pedal is released. Because the soft pedal

has no effect on notes already playing, you should

operate it just before playing the notes to be softened.

Using pedals for Play and Stop operations

Yo u can configure either the center or left pedal to operate in

the same way as the control panel’s [PLAY/STOP] button

using the corresponding Function parameter (page 40).

Using an optional pedal unit

• Be sure to turn off the digital piano before connecting or disconnecting a pedal

unit.

LP-255

(sold separately)

L-255

(sold separately)

NOTE

If you operate the damper pedal here, notes

being played at this time and all subsequent

notes will be sustained for longer than usual.

• When a Jazz Organ Voice has been selected, the pedal on the left will instead

control the speed of the rotary speaker effect.

If you operate the sostenuto pedal here,

notes produced by keys still held down at

this time—but not newly played notes—will

be sustained until the pedal is released.

NOTE

P-255 Owner’s Manual

Selecting & Playing Voices

Using the following procedure, you can select the

instrument sound (such as piano or organ) to use when

playing the keyboard.

Press a Voice button to select a Voice

from the corresponding category.

You can cycle through the category’s Voices by

pressing the button multiple times. Refer to the

Voice List (page 51) for details of the Voices

included.

Play the keyboard to hear how the

selected Voice sounds.

A number of demo songs have been prepared so that

you can conveniently familiarize yourself with the

sound of each Voice, and these songs can be played as

described below. Refer to the Voice Demo Song list

for the names of the individual demo songs.

Voice Demo Song list

• The demonstration Songs listed above are short rearranged excerpts of the

original compositions.

Press the [DEMO] button to start play-

back.

The Grand Piano demo song will start to play, and

all demo songs will continue to play in sequence

until you stop playback. If necessary, you can

press a Voice button during playback to skip to the

corresponding demo song.

Press the [PLAY/STOP] button or the

[DEMO] button to stop playback.

Selecting Voices

• When you press a Voice button, the most-recently selected Voice will be

shown on the display.

• Although your digital piano can adjust the loudness of Voices based on the

strength of your playing, certain Voices do not support this Touch Sensitiv-

ity feature. Refer to the Voice List (page 51) for details.

NOTE

Listening to the Voice demo songs

Voice

button

Display

Voice

Name

Title

Com-

poser

[PIANO]

GP3

Ballad

Grand

Intermezzo, 6 Stücke,

op.118-2

Brahms

[ORGAN]

or3

Pipe

Organ

Principal

Herr Christ, der ein'ge

Gottes-Sohn, BWV.601

J. S.

Bach

or4

Pipe

Organ

Tutti

Triosonate Nr.6, BWV.530

J. S.

Bach

[CLV./

VIB.]

CL1

Harpsi-

chord 8’

Concerto a cembalo

obbligato, 2 violini, viola e

continuo No.7, BWV.1058

J. S.

Bach

CL2

Harpsi-

chord

8’+4’

Gigue, Französische

Suiten Nr.5, BWV.816

J. S.

Bach

• Demo songs cannot be played during recording (page 25) or file opera-

tions (page 30).

• The digital piano does not transmit MIDI data when demo songs are play-

ing. In addition, MIDI data will not be received at this time.

• The tempo of demo songs cannot be changed; in addition, the Part Cancel

function (page 23) and the A-B Repeat function (page 23) cannot be used

with these songs.

NOTE

Main Operations

Selecting & Playing Voices

P-255 Owner’s Manual

Using Dual mode as described below, you can layer

two Voices on the keyboard and play them together.

By combining Voices of different types in this way,

you can create a composite Voice of greater richness

and texture.

Select the two Voices you wish to layer

using the corresponding Voice buttons.

Your digital piano will get the selected Voices

ready for playing.

For details on selecting voices, see page 13.

Activate Dual mode.

Press the Voice buttons for the two selected Voices

together and verify that they both light up.

Voice 1 and Voice 2

Of the two Voices selected for layering, the one

selected using the Voice button closer to the left

will be designated Voice 1; the other, Voice 2.

When you activate Dual mode, the Voices’ octave

settings and volume balance in addition to their

reverb and effect types and depths will be auto-

matically optimized. If necessary, however, you

can change these settings using the corresponding

Function parameters (page 40). Furthermore,

these settings can be changed individually for

Voice 1 and Voice 2.

Leave Dual mode.

Press any Voice button to return to normal play

mode.

Using Split mode as described below, you can divide

the keyboard into left and right sides and assign differ-

ent Voices to each. You could, for example, play a

bass part with your left hand using the Wood Bass or

Electric Bass Voice while playing a melody using a

different Voice with your right hand.

Activate Split mode.

Press the [SPLIT] button and verify that it lights up.

By default, the Wood Bass Voice will be assigned

to the left side of the keyboard at this time.

Set the split point.

The split point is the location at which the key-

board is divided. To set this point, press the corre-

sponding key with the [SPLIT] button held down.

Alternatively, you can move the split point by

pressing the [-/NO] and [+/YES] buttons with the

[SPLIT] button held down. To restore the split

point to the default F#2 setting, press the [-/NO]

and [+/YES] buttons together with the [SPLIT]

button held down.

Whenever the [SPLIT] button is being held down,

the display will show the current split point.

Examples of split points as shown on display

Layering two Voices with Dual mode

• Two different voices corresponding to the same Voice button—such as

Grand Piano and Live Grand—cannot be layered.

• Dual mode and Split mode cannot be activated at the same time.

• You can jump directly to Function parameter F3.1 (page 42) by pressing

the [FUNCTION] button with the buttons for the two layered Voices held

down.

NOTE

Voice 1 Voice 2

NOTE

Dividing the keyboard with Split

mode

• Dual mode and Split mode cannot be activated at the same time.

•

The key that defines the split point is included in the left side of the keyboard.

• The split point can also be set using the corresponding Function parameter

(page 40).

NOTE

F#2 (default setting)

A-1 C1 C2 C3 C4 C5 C6 C7

NOTE

2 F~2 E_2

Indicates a sharp

key (#).

Indicates a flat

key (b).

F2 F#2Eb2

Selecting & Playing Voices

P-255 Owner’s Manual

Select a Voice for the right side.

Use the corresponding Voice button to make your

selection.

Select a Voice for the left side.

Use the corresponding Voice button with the

[SPLIT] button held down to make your selection.

(Whenever the [SPLIT] button is being held

down, the Voice button corresponding to the left

side’s Voice will light up.)

Play the keyboard and listen to the sounds pro-

duced.

When you activate Split mode, the Voices’ octave

settings and volume balance in addition to their

reverb and effect types and depths will be auto-

matically optimized. If necessary, however, you

can change these settings using the corresponding

Function parameters (page 40). Furthermore,

these settings can be changed individually for the

left and right Voices.

Leave Split mode.

Press the [SPLIT] button once again and verify

that its light goes out.

Using the digital piano’s Reverb function, you can add

reverberation similar to that of a concert hall to indi-

vidual Voices. Whenever you select a Voice, the most

suitable reverb will be automatically set; however, you

can freely set the reverb type and depth.

Setting the reverb type

Whenever you press and release the [REVERB] but-

ton, the current reverb type will be shown on the dis-

play. You can then cycle through the different types by

pressing the [REVERB] button the required number

of times.

Reverb types

Setting the reverb depth

You can change the setting by pressing the [-/NO] and

[+/YES] buttons with the [REVERB] button held

down.

•Available settings: 0 (no effect) to 20 (maximum reverb depth)

To restore the Voice to its default reverb depth, press

the [-/NO] and [+/YES] buttons together with the

[REVERB] button held down.

Adding reverb

Display Type Description

rt1

Room

This setting adds a continuous reverb

effect similar to the acoustic reverberation

you would hear in a small room.

rt2

Hall 1

This setting simulates the natural reverber-

ation of a small concert hall.

rt3

Hall 2

This setting simulates the natural reverber-

ation of a large concert hall.

rt4

Stage

This setting reproduces a reverb effect sim-

ilar to that of a live music environment.

OFF

Off

With this setting, no reverb is applied to the

Voice and the [REVERB] button’s light will

go out. Even in this situation, however, a

soundboard resonance effect similar to that

of an acoustic piano will still be applied to

certain Voices—specifically, Grand Piano,

Live Grand, Ballad Grand, and Bright

Grand.

Selecting & Playing Voices

P-255 Owner’s Manual

Using the digital piano’s Effect function, you can add

a range of different audio effects to individual Voices.

Whenever you select a Voice, the most suitable effect

will be automatically set; however, you can freely set

the effect type and depth.

Setting the effect type

Whenever you press and release the [EFFECT] but-

ton, the current effect type will be shown on the dis-

play. You can then cycle through the different types by

pressing the [EFFECT] button the required number of

times.

Effect types

Adjusting the effect depth

You can change the setting by pressing the [-/NO] and

[+/YES] buttons with the [EFFECT] button held

down.

•Available settings: 0 (no effect) to 20 (maximum reverb depth)

To restore the Voice to its default effect depth, press

the [-/NO] and [+/YES] buttons together with the

[EFFECT] button held down.

The Transpose function allows you to shift the pitch

of both the keyboard and song playback. In this way,

you can match your playing to the key of another

instrument or a singer without having to change what

you actually play on the keyboard. Transpose settings

are made in semitone units. For example, if you set the

transpose amount to “5,” the key C will produce the

pitch F. You could, therefore, play a song as if it was

in C major and the digital piano would transpose it to

the key of F major.

Setting the transpose amount

Use the [-/NO] and [+/YES] buttons while holding

down the [TRANSPOSE] button to set the transpose

amount in semitone units. To restore the non-trans-

posed default setting (0), press the [-/NO] and

[+/YES] buttons together with the [TRANSPOSE]

button held down.

•Available settings: -12 (one octave lower) to 0 (normal pitch)

to 12 (one octave higher)

Turning transpose on and off

You can press the [TRANSPOSE] button to toggle

transpose on and off. The button will light up when

the instrument is being transposed. Its light will go out

when transpose is turned off or the transpose amount

is 0.

Adding effects

Display Type Description

Et1

Chorus

This setting can be used to make the Voice

sound thicker and wider.

Et2

Phaser

This setting adds a distinctive sweeping

effect to the sound.

Et3

Tremolo

This setting can be used to add a shudder-

ing volume effect.

Et4

Rotary

speaker

This setting produces the vibrato effect of a

rotary speaker.

OFF

Off

With this setting, no effect is applied to the

Voice and the [EFFECT] button’s light will

go out.

Transposing

• The playback of audio songs cannot be transposed.

Transpose amount

NOTE

Selecting & Playing Voices

P-255 Owner’s Manual

Using the Tuning setting, you can fine tune the pitch

of the entire instrument. This can be extremely useful

when playing your digital piano along with other

instruments or recorded music.

Tuning is set using Function parameter F1. Refer to

page 41 for details.

The degree to which the instrument reflects differ-

ences in the strength of your playing in the sound pro-

duced is referred to as touch sensitivity, and this

setting can be adjusted. (Changing the touch sensitiv-

ity has no effect on the weights of the keys.)

Touch sensitivity is set using Function parameter

F6.8. Refer to page 45 for details.

Using your digital piano’s Equalizer function, you can

adjust the tone of overall instrument by increasing or

decreasing the gain in three different frequency bands.

The [EQ] section of the control panel contains a slider

for each of these bands, making it very easy to equal-

ize to your liking.

• LOW slider.....Used to adjust the tone in the Low

frequency band.

• MID slider ......Used to adjust the tone in the Mid

frequency band.

• HIGH slider ...Used to adjust the tone in the High

frequency band.

When you move a slider up, the volume of the corre-

sponding frequency band will be boosted and vice-

versa.

• Move the LOW slider up and down to adjust the

sound’s thickness and punch.

• Move the MID slider up and down if you wish to

adjust the clarity of the sound.

• Move the HIGH slider up and down to adjust the

brightness and brilliance of the sound.

Tuning the instrument

Changing the touch sensitivity

Adjusting the tone

• The Equalizer function has no effect on audio songs or sound input via the [AUX

IN] jack.

NOTE

Selecting & Playing Voices

P-255 Owner’s Manual

Using your instrument’s Sound Boost function when

playing along with other instruments, you can raise its

volume and enhance the presence of your perfor-

mance without making it any less expressive. This

function is particularly useful when you want not only

notes played very loud, but also those played softly, to

be clearly audible.

The [SOUND BOOST] button can be used to toggle

this function on and off. The button will light up when

the sound is being boosted.

Setting the Sound Boost type

You can change the type of Sound Boost applied to

the instrument’s sound using the [-/NO] and [+/YES]

buttons with the [SOUND BOOST] button held down.

To restore the default setting, press the [-/NO] and

[+/YES] buttons together with the [SOUND BOOST]

button held down.

•Available settings: 1 (minimum boost) to 3 (maximum boost)

•Default setting: 2

Sound Boost type list

• If performing live as part of a band:

.............................................................. See page 36.

• If singing and playing on your own:

.............................................................. See page 38.

As described below, your digital piano’s Panel Lock

function allows you to temporarily disable control-

panel buttons to prevent them being operated uninten-

tionally while performing.

Lock the control panel.

Press the [EFFECT] and [SOUND BOOST] but-

tons together. All control-panel buttons with the

exception of the [ ] Standby/On switch will be

disabled. The message “---” is shown on the dis-

play while the control panel is locked.

Control panel locked:

Unlock the control panel.

Press the [EFFECT] and [SOUND BOOST] but-

tons together once again. The control panel will be

unlocked and the display will return to the normal

tempo or song number screen.

Boosting the overall sound

Display/Type Description

Producing smooth dynamics, this type is ideal

for solo performances of uplifting songs and

the like.

This type produces a smoother, clearer sound

than Type 1, making it the perfect choice when

singing and playing at the same time.

In addition to a brighter, more-powerful sound

than Type 2, this type also has a clearer attack.

As such, it is an excellent choice when, for

example, performing as part of a band.

• If necessary, you can use the Equalizer (EQ) to further accentuate the effect of the

Sound Boost function (page 17).

NOTE

Locking the control panel

• Locking the control panel has no effect on the [ ] Standby/On switch, the

[MASTER VOLUME] slider, the [EQ] sliders, or any connected pedals

(pedal unit or sustain pedal).

NOTE

P-255 Owner’s Manual

Using the Metronome

Playing your digital piano along with the built-in metronome is a great way to perfect your timing. The following

describes how to use this function.

Turn on the metronome.

Press the [METRONOME] button and verify that

the metronome starts to play.

Adjusting the tempo

You can adjust the metronome tempo using the

[-/NO] and [+/YES] buttons with the [TEMPO]

button held down. Settings between 5 and 500

beats per minute (BPM) are supported. To restore

the default setting of 120 BPM, press the [-/NO]

and [+/YES] buttons together with the [TEMPO]

button held down.

Setting the time signature

Whenever the [METRONOME] button is being

held down, the display will show the current time

signature. You can change this setting using the

[-/NO] and [+/YES] buttons with the [METRO-

NOME] button held down. Settings of between 0

and 15 are supported—for example, you can set

“4” if you need a metronome with four beats per

measure. The first beat of each measure is

accented with a bell-type sound, and clicks are

used for the other beats. When the time signature

is set to “0,” clicks are used for all beats. To

restore the default setting of 0, press the [-/NO]

and [+/YES] buttons together with the [METRO-

NOME] button held down.

Turn off the metronome.

You can stop the metronome by pressing the

[METRONOME] button once again.

• You can set the metronome volume using the corresponding Function

parameter (page 40).

• If a MIDI song (page 21) has been selected:

Each MIDI song has its own default settings for tempo and time signature.

Whenever you play one of these songs, its tempo and time signature will

be applied, canceling any setting you have made on the instrument.

The beat indicator

flashes in time as the

metronome plays.

120.

NOTE

Time signature

NOTE

P-255 Owner’s Manual

Playing Rhythm Tracks

Your digital piano’s Rhythm function provides ten different rhythm tracks for you to play along with. The follow-

ing describes how to use this function.

Turn on a rhythm track.

Press the [RHYTHM] button and verify that a

rhythm track starts to play. If intro playback has

been turned on using the corresponding Function

parameter (page 40), the rhythm track’s intro sec-

tion will be played first.

Adjusting the tempo

You can adjust the rhythm track tempo using the

[-/NO] and [+/YES] buttons with the [TEMPO]

button held down. Settings between 5 and 500

beats per minute (BPM) are supported. To restore

the default setting of 120 BPM, press the [-/NO]

and [+/YES] buttons together with the [TEMPO]

button held down.

Turn off the rhythm track.

You can stop a rhythm track by pressing the

[RHYTHM] button once again. If ending play-

back has been turned on using the corresponding

Function parameter (page 40), the rhythm track’s

ending section will be played first.

Selecting a rhythm track

Whenever the [RHYTHM] button is being held down,

the display will show the number of the current

rhythm track. Refer to the Rhythm Track list for the

corresponding names.

You can select rhythm tracks 1 to 10 using the [-/NO]

and [+/YES] buttons with the [RHYTHM] button held

down.

To restore the default setting of 1, press the [-/NO]

and [+/YES] buttons together with the [RHYTHM]

button held down.

Rhythm Track list

• A rhythm track cannot be played together with the metronome.

• The rhythm track volume can be set using the corresponding Function

parameter (page 40).

120.

The beat indicator

flashes in time as a

rhythm track plays.

NOTE

Number Track name

8 Beat 1

8 Beat 2

16 Beat 1

16 Beat 2

Shake

12/8

Shuffle

Swing

Bossanova

Jazz Waltz

ページを読み込んでいます...

Yamaha P-255, PS-1, PSR-EW300 取扱説明書

関連論文

その他の書類