Philips FC8820/81 ユーザーマニュアル

FC8820

FC8810

FC8820

Wheels stuck

ݓઁहሂ

Top cove r or dust container not placed properly

רۆࠋࠦӧ๥໇٦ݾ

Bumper stuck

ߓԎሑᇆहሂ

Robot lifted up from floor

՚ֽϴุఓਘᇊୃስײᆋ०༏ӧచ

Colour of floor too dark

ֽϴဂ೨ขτ

Battery not inserted properly / Charging error (switch is off)

׌ԁ໇ሑݾԍ׌մ༆Ĳऻܵၜܵтĳ

5

6

4

3

2

1

7

8

9

1516

13

12

14

11

10

17

18

19

21

20

22

24

25

26

23

2928

27

30

1

FC8820, FC8810

ENGLISH 6

简体中文 26

6

Introduction

Congratulations on your purchase and welcome to Philips!

To fully benet from the support that Philips offers, register your product at

www.philips.com/welcome.

Your robot (Fig. 1)

1 Handle of dust container lid

2 Dust container lid

3 Filter

4 Dust container

5 Top cover

6 Error codes table

7 Fan

8 Bumper

9 On/off button (switches robot on or to standby)

10 Power switch (switches robot on or off)

11 Front wheel

12 Side brush shafts

13 Drop-off sensors

14 Wheels

15 Battery cavity

16 Suction opening

17 Side brushes

18 Rechargeable battery

19 Battery cavity cover

20 Fixation blocks for dry wipes

21 Dry wipe holder

22 Dry wipes

23 Battery holder

24 Remote control

25 Charging cord

26 Pointer

27 Virtual wall unit

28 Docking station

29 Adapter

30 Small plug

Displays and control panels

Control panel of docking station

1 Display with time, day and programming indications

2 Adjusting and setting buttons

3 Battery indicator

1

2

3

ENGLISH

Remote control

1 Navigation buttons and on/off

2 Cleaning time buttons

3 Cleaning mode buttons

4 Fan speed buttons

5 Docking button

Pointer (FC8820)

1 Pointer button

2 On/off button

3 Cleaning mode buttons

4 Cleaning time buttons

5 Docking button

How your robot works

What your robot cleans

This robot is equipped with features that make it a suitable cleaner to help

you clean the oors in your home.

The robot is especially suitable for cleaning hard oors, such as wooden,

tiled or linoleum oors. It may experience problems cleaning soft oors,

such as carpet or rugs. If you use the robot on a carpet or rug, please stay

close by the rst time to see if the robot can deal with this type of oor.

The robot also needs supervision when you use it on black and shiny

hard oors.

How your robot cleans

Cleaning system

The robot has a 3-stage cleaning system to clean your oors efciently.

- The two side brushes help the robot clean in corners and along walls.

They also help to work dirt loose from the oor.

1

2

3

45

5

4

3

2

1

ENGLISH 7

- The suction power of the robot picks up loose dirt and transports it

through the suction opening into the dust container.

- The robot comes with a dry wipe holder that allows you to clean your

hard oor even more thoroughly with dry wipes.

Cleaning patterns

In its auto cleaning mode, the robot uses an automatic sequence of

cleaning patterns to clean each area of the room optimally.

The cleaning patterns it uses are:

1 Z-pattern or zigzag pattern

2 Random pattern

3 Wall-following pattern

4 Spiral pattern

During auto cleaning, the robot uses these patterns in a xed sequence:

1 Z-pattern

2 Random pattern

3 Wall-following pattern

4 Spiral pattern

- When the robot has completed this sequence of patterns, it starts

moving in Z-pattern again. The robot continues to use this sequence

of patterns to clean the room until the rechargeable battery is empty,

or until it is switched off manually.

- If the robot detects a particularly dirty area during its cleaning run,

it switches to spiral mode and to turbo fan speed to ensure thorough

dirt removal.

Note: You can also select each mode individually by pressing the appropriate

button on the remote control or pointer (FC8820 only). For more details,

see chapter ‘Using your robot’, section ‘Cleaning modes’.

ENGLISH8

How your robot avoids height differences

- The robot has three drop-off sensors in its bottom. It uses these

drop-off sensors to detect and avoid height differences such as

staircases.

Note: It is normal for the robot to move slightly over the edge of a height

difference, as its front drop-off sensor is located behind the bumper.

Caution: In some cases, the drop-off sensors may not detect a staircase

or other height difference in time. Therefore monitor the robot carefully

the rst few times you use it, and when you operate it near a staircase

or another height difference.

Before rst use

Mounting the side brushes

1 Unpack the side brushes and place the robot upside down on a table

or on the oor.

2 Push the side brushes onto the shafts on the bottom of the robot.

Note: Make sure you attach the side brushes properly. Press them onto the

shaft until you hear them lock into position with a click.

Inserting the rechargeable battery into the robot

You have to insert the rechargeable battery before use.

1 Press the ribbed sections on the battery cavity cover to unlock it.

2 Slide the battery cavity cover off the robot.

3 Remove the plastic from the rechargeable battery.

1

2

ENGLISH 9

4 Place the rechargeable battery into the battery cavity.

Note: Make sure that the print on the battery points upwards and that

the connectors point in the right direction.

5 Slide the battery cavity cover back onto the robot.

Removing the protection tag from the remote control

The remote control works on a CR2025 coin-shaped battery. This battery

is protected with a protection tag that has to be removed before use.

1 Pull the battery protection tag out of the battery compartment of

the remote control.

, Now the remote control is ready for use.

Preparing for use

Installing the docking station

1 Insert the small plug of the adapter into the socket on the docking

station (1) and insert the adapter into the wall socket (2).

The display of the docking station lights up.

2 Place the docking station on a horizontal, level oor against the wall.

Tip: To ensure the docking station stays rmly in the selected spot, you can

fasten it to the wall with screws or with two strips of double-sided tape.

Note: Make sure that there are no obstacles or height differences 80cm in

front, 30 cm to the right and 100cm to the left of the docking station.

1

2

100

30

80

ENGLISH10

Charging

When you charge the rechargeable battery for the rst time and when

the rechargeable battery is empty, the charging time is four hours.

Your robot can be charged in two ways:

- On the docking station, either manually or automatically during use;

- By connecting the robot directly to the mains

Note: When the rechargeable battery is fully charged, your robot can clean

for up to 100 minutes.

Charging on the docking station

1 Place the robot on the plugged-in docking station.

2 Press the power switch to switch on the robot.

3 The battery indicator on the display of the docking station and

the light in the on/off button on the robot start ashing.

Note: Because this is the rst time you charge the robot, the display of

the robot shows the booting indicator.

4 When the rechargeable battery is fully charged, the battery indicator

on the display of the docking station and the light in the on/of button

on the robot stop ashing.

Charging automatically during use

1 When the robot has nished cleaning or when only 15% of the

battery power remains, it automatically returns to the docking

station to recharge. When the robot returns to the docking station,

the light in the on/off button ashes.

2 When the robot is positioned correctly on the docking station, the

battery indicator on the display of the docking station starts to ash.

FC8820 FC8810

30

24

ENGLISH 11

3 When the rechargeable battery is fully charged, the battery indicator

on the display of the docking station and the light in the on/of button

on the robot stop ashing.

Note: The robot only returns to the docking station automatically when it

started cleaning from the docking station.

Charging directly from the mains

1 Insert the small plug of the adapter into the socket on the robot

(1). Insert the adapter into a wall socket (2).

2 Press the power switch to switch on the robot.

3 When the robot is connected to the mains correctly, the light in

the on/off button of the robot starts ashing. This indicates that the

rechargeable battery is being charged.

4 When the rechargeable battery is fully charged, the light in the on/off

button of the robot stops ashing.

Preparing the room for a cleaning run

- Before you start the robot on its cleaning run, make sure that you

remove all loose and fragile objects from the oor.

Using your robot

Starting and stopping

1 Press the on/off button. The light in the on/off button goes on and

the robot starts cleaning.

- You can press the on/off button on the robot.

- You can also press the on off button on the remote control or on

the pointer (FC8820).

FC8820 FC8810

30 24

1

2

ENGLISH12

2 Unless you press one of the mode buttons, the robot continues

cleaning in auto cleaning mode until its battery runs low. In auto

cleaning mode it follows repeated sequences of Z-pattern, random,

wall-following and spiral movements. For more information on the

cleaning modes, see section ‘Cleaning modes’.

3 When the battery runs low, the light in the on/off button starts

ashing and the robot returns to the docking station to charge.

4 You can also press the on/off button to interrupt or stop the

cleaning run. If you press the on/off button again and there is still

enough energy in the rechargeable battery, the robot continues

cleaning in the auto cleaning mode.

5 You can also make the robot return to the docking station before

the rechargeable battery runs low by pressing the docking button on

the remote control or the pointer (FC8820). The docking indicator

on the display of the robot lights up and the robot returns to the

docking station.

Note: If you did not start the robot from the docking station, it does not return

to the docking station automatically when the rechargeable battery runs low.

If there is still enough energy in the rechargeable battery, you can press the

docking button to make the robot return to the docking station.

If the rechargeable battery is completely empty, you have to place the robot

on the docking station manually.

Cleaning modes

Next to the auto cleaning mode, this robot has four individual cleaning

modes that can each be activated by pressing the appropriate button.

Z-pattern mode

- In Z-pattern mode, the robot cleans by making Z-shaped loops

through the room to clean large areas.

Random mode

- In this mode, the robot cleans the room in a mixed pattern of straight

and crisscross movements.

ENGLISH 13

Wall-following mode

- In this mode, the robot follows the walls of the room to give the area

alongside the walls an extra clean.

Spiral mode

- In this mode, the robot makes a spiral movement with the fan at turbo

speed to clean a dirty area thoroughly.

Manual driving

1 Use the arrow buttons above and below and to the left and right

of the on/off button on the remote control to navigate the robot

through the room.

Note: Do not press the downward arrow when the robot is close to a height

difference or a staircase.

Using the cleaning time buttons

- Press the maximum cleaning time button to make the robot clean in

auto cleaning mode until its rechargeable battery runs low.

When the robot has nished cleaning, it returns to the docking station

automatically if it started from the docking station. If the robot started

from another point in the room, press the docking button to send it

back to the docking station.

- The other cleaning time buttons allow you to let the robot operate for

60, 45 and 30 minutes respectively. When the cleaning time is nished,

the robot automatically returns to the docking station when it started

from the docking station. If the robot started from another point in the

room, press the docking button to send it back to the docking station.

ENGLISH14

Using cleaning programs

Setting clock time and day

If you want to use cleaning programs, you have to set the clock time and

the day of the week on the display of the docking station rst. For the

pictures that belong to the steps below, see the fold-out pages at the back.

1 Press the set button. The set mode indicator and the clock time

indicator start ashing.

2 Press the select button once. The hour indication starts ashing.

3 Use the + and - buttons on the remote control to set the hour.

The set hour appears on the display.

4 Press the select button to conrm the hour set.

The minutes indication starts ashing.

5 Use the + and - buttons on the remote control to set the minutes.

The set minutes appear on the display.

6 Press the select button to conrm the minutes set. The indication

‘Su’ for Sunday starts ashing.

7 Use the + and - buttons on the remote control to set the current

day of the week.

8 Press the select button to conrm the day of the week.

9 Press the set button to conrm the clock time and day of the week

setting. Both the set mode indicator and the clock time indicator

stop ashing and turn solid.

Programming cleaning times

If you have set the time and the day of the week on the display of the

docking station, you can program cleaning times for your robot. For the

pictures that belong to the steps below, see the fold-out pages at the back.

The programming options available are:

Program Indication on display

Cleaning every day All day indications are on

Cleaning on weekdays Mo to Fri indications are on

Cleaning on 2 consecutive days Indications of 2 days are on, e.g. Fri and Sa

Cleaning 1 day a week Indication of selected day is on

1 Press the set button. The set mode indicator and the cleaning

program indicator start ashing.

2 Press the select button once. The hour indication starts ashing.

3 Use the + and - buttons on the remote control to set the hour.

The set hour appears on the display.

4 Press the select button to conrm the hour set.

The minutes indication starts ashing.

ENGLISH 15

5 Use the + and - buttons on the remote control to set the minutes.

The set minutes appear on the display.

6 Press the select button to conrm the minutes set.

The indication ‘Su’ for Sunday starts ashing.

7 Use the + and - buttons on the remote control to toggle between

cleaning programs (see the table above for the programming options

available).

8 Press the select button to conrm the program selected.

9 Press the set button to conrm the programming. Both the set mode

indicator and the cleaning program indicator stop ashing and turn

solid.

10 When you have set a cleaning program, the display shows the cleaning

program indicator and the day or days selected. If you leave the robot

on standby and its rechargeable battery is fully charged, it will start

cleaning at the programmed time on the programmed day or days.

Fan speed buttons (FC8820)

You can use the fan speed buttons to increase the fan speed to turbo or to

switch off the fan. The default setting is normal fan speed.

1 Turbo fan speed increases the suction power of the robot.

2 You can switch off the fan by pressing this button.

3 Press this button for normal fan speed.

Clap response

- When all icons on the display ash, the robot is malfunctioning.

To stop the icons ashing and see what is wrong, clap you hands once.

This makes the error code appear on the display. See chapter

‘Error codes’ for the explanation of what these error codes mean.

Using the dry wipe attachment

The dry wipe attachment is a feature that allows you to clean hard oors

with dry wipes.

Preparing the dry wipe attachment for use

1 Turn the robot upside down and place it on the oor or on a table.

2 Place the dry wipe on a table and place the dry wipe attachment on

the wipe with its xation lugs pointing towards you.

1

2

3

ENGLISH16

3 Fold both ends of the dry wipe around the dry wipe attachment

and fasten the dry wipe onto the attachment by pushing the xation

blocks into the recesses.

4 Insert the xation lug of the dry wipe attachment into the opening

just behind the wheel on one side of the robot and push until you

hear it lock into place with a click. Then repeat these actions on

the other side.

5 Turn the robot and place it on the oor on its wheels with the dry

wipe attachment touching the oor.

Using the robot with the dry wipe attachment

When the dry wipe attachment is attached, you can use the robot in any

mode and on all hard oors. Do not use the dry wipe attachment on

carpet or rugs.

Removing the dry wipe attachment

Remove the dry wipe attachment as soon as you have nished wiping

the oor.

1 Turn the robot upside down and place it on the oor or on a table.

2 Push one end of the dry wipe attachment towards the wheel on

the other side of the robot to release it. Then pull the attachment

off the robot.

Using the pointer (FC8820)

Charging the pointer

The pointer has a rechargeable battery that can be charged with

the USB cable supplied.

1 Insert the micro-USB plug into the socket in the bottom of the

pointer.

2 Insert the USB plug into a USB charger or a USB port on your

laptop.

1

2

ENGLISH 17

3 The charging light on the pointer lights up solid. Charging takes

30 minutes. When the charging light goes off, the rechargeable

battery is fully charged.

Navigating the robot with the pointer

- When you press and hold the pointer button, the pointer emits a beam

of infrared light. With this beam you can drag the robot in a particular

direction. As long as you keep the button pressed and keep pointing

in the direction you want the robot to move, it continues to move in

that direction. When you release the pointer button, the robot starts

cleaning in auto cleaning mode.

- With the pointer you can send the robot to a specic area in the room

to give this area an extra-thorough clean.

Using the virtual wall unit (FC8820)

Placing the batteries in the virtual wall unit

The virtual wall unit operates on four AA batteries.

1 Push the two release tabs at the bottom of the back cover (1)

and slide the back cover upwards and off the virtual wall unit (2).

2 Take four new AA batteries from the pack and insert them into

the battery compartment of the virtual wall unit.

Note: Make sure the + and - poles of the batteries point in the right direction.

3 Slide the back cover onto the virtual wall unit again.

50-70

50-7

0

50-70

1

2

ENGLISH18

Positioning the virtual wall unit to stop the robot

You can use the virtual wall unit to prevent the robot from entering a

room or area that you want to keep it out of.

1 Place the unit at a spot beyond which you do not want the robot to

go, e.g near an open door to a room that is off-limits to the robot or

at the top of a staircase.

2

Switch on the virtual wall unit with the on/off slide on top of the unit.

3 Switch on the robot for a normal cleaning run.

4 When the robot comes too close to the virtual wall unit, the light

on the virtual wall unit starts ashing and the virtual wall unit emits

a beam of infrared light. This beam of infrared light makes the robot

change its course and move away from the virtual wall unit.

Cleaning and maintenance

Emptying and cleaning the dust container

Empty and clean the dust container when the dust container full icon on

the display of the robot lights up.

1 Remove the top cover.

Note: Make sure the power switch is in ‘off ’ position.

ENGLISH 19

2 Pull up the handle of the dust container lid and lift the dust container

out of the dust container compartment.

Note: When you remove or reinsert the dust container, take care not to

damage the blades of the motor fan.

3 Carefully lift the lid off the dust container and take out the lter.

4 Shake the dust container over a dustbin to empty it. Clean the lter

and the inside of the dust container with a cloth or a toothbrush

with soft bristles. Also clean the suction opening in the bottom of the

dust container.

Caution: Do not clean the dust container and the lter with water or in

the dishwasher.

5 Put the lter back into the dust container. Then place the lid on the

dust container.

6 Put the dust container back into the dust container compartment

and put the top cover back onto the robot.

Caution: Always make sure the lter is present inside the dust container.

If you use the robot without the lter inside the dust container,

the motor will be damaged.

1

2

ENGLISH20

ページが読み込まれています...

Philips FC8820/81 ユーザーマニュアル

このマニュアルも適しています

Philips FC8820/81 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント