Genmitsu PROVerXL 4030 ユーザーマニュアル

V1.4 March 2023

USER MANUAL

PROVerXL 4030 CNC Router

Contents /

English 01 - 36

37 - 72 PROVerXL 4030 CNC

Genmitsu

NEMA 23 (2 Phase, 3A, Bipolar)

0.1m (0.003937inch)

06

10 11

9Drag Chain Mount (2) Drag Chain Mount Cable Management

MDF Spoil Board

12

Electrical Parts List

USB Cable A-B

16 17 Power Cable EU)

1.2m

PROVerXL

Control Center

15

Bakelite Sheet

175 x 100 x 5mm

13 MDF Board

175 x 100 x 5mm

14

07

25 User Manual

Tools/Accessories Parts List

Probe

Z-Height Mapping Probe

19

24

(10) Engraving Bit Kit

30 Degree, 0.2mm Cutting area,

3.175 Diameter

20

22 23

18 (4) Material Clamp

21 (10) Nano Blue Coat Bits

3.175mm Shank, Cutting Edge

Diameter: 0.8-3.0mm Wrench

Nylon Braided Wrap

340mm USB Stick

26

(4) Allen Wrench

2.0mm, 3.0mm, 4.0mm, 5.0mm

3.175mm (1/8”)

08

27 (2) M5 T- Nut

(Pre-assembled) 28 29

(4) M5 x 8mm

Socket Cap Screw (14) M5 x 16mm

Socket Cap Screw

Screws/Other Parts List

31 (8) M5 x 50mm

Socket Cap Screw

35 (3) Coupler 36 37

(10) 5mm

Spring Washer (10) 5mm

Flat Washer 38 (4) Fuses, 10A 39 Laser Mount

32 (4) M5 x 55mm

Socket Cap Screw 33 (2) M4 x 6mm

Socket Cap Screw 34 (2) M4 x 8mm

Socket Cap Screw

30 (6) M5 x 20mm

Socket Cap Screw

09

Optional Accessories (Not Included)

Consider following optional upgrades or accessories to make your CNC experience better!

You can find them on www.sainsmart.com.

Save 10% with discount code PROVerXL

CNC Router Bits

Essential Kit

Scan QR codes to learn more

Offline Controller for

PROVerXL 4030 52mm Dust Shoe

for PROVerXL 4030 1010 Extension Kit

for PROVerXL 4030

(2) Stepper

Motor Mount

12

2.2 Finishing your Base Assembly

What you will need

MDF Spoil board

12

30 (6) M5 x 20mm

Socket Cap Screw

Y-Axis Base Assembly

229 (4) M5 x 16mm

Socket Cap Screw

(2) Dust Baffle

522 Allen Wrench

Step 1: Position the MDF Spoilboard on the

PROVerXL Base and align each Dust Baffle

to the side of the spoilboard. Align with the

screw holes and tighten down with the

M5 x 16mm screws.

Step 2: Align the MDF Spoilboard with the screw holes at the front

and back of the machine. Be sure the board is right side up (Threaded

Inserts should be towards the bottom. If you install it in reverse the

mounting screws will protrude from the top of the spoil board).

Tighten with M5 x 20mm crews.

16

2.4 Finishing your X-Axis Gantry

What you will need

28 (2) M5 x 8mm

Socket Cap Screw

X-Axis & Spindle

Z-Axis Assembly

19Drag Chain Mount

Step 1: Position the X-Axis Limiter to the rear of the Spindle Carriage as shown in the diagram. Install the bracket and tighten

the screws.

22 Allen Wrench

ページを読み込んでいます...

Genmitsu PROVerXL 4030 ユーザーマニュアル

関連論文

その他の書類