SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
No. 11837
WINGSPAN: 1375mm
SAFETY PRECAUTIONS
This radio control model is not a toy!
First-time builders should seek the advice of experienced modellers
before commencing assembly and if they do not fully understand
any part of the construction.
Assemble this kit only in places out of childrenÕs reach!
Take enough safety precautions prior to operating this model.
You are responsible for this modelÕs assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference, even after completing the assembly.
For Intermediate
& Advanced Flyers.
THE FINEST RADIO CONTROL MODELS
R
INSTRUCTION MANUAL
2
2
4~14
15
16
Before commencing assembly, please read these instructions thoroughly!
© 2000 KYOSHO
REQUIRED FOR OPERATION
BEFORE YOU BEGIN
ASSEMBLY
SPARE PARTS
OPERATING YOUR MODEL SAFELY
RADIO CONTROLLED ENGINE POWERED SCALE BIPLANE
KYOSHO SUPER QUALITY SERIES
2
1
A minimum 4 channel radio for airplanes (with 5 servos),
and dry batteries.
A minimum 4 channel transmitter,
configured for aircraft.
3 12
12 AA-size Batteries
Ensure you read and understand the instructions included with your radio.
Sharp Hobby Knife Phillips Screwdriver (L, M, S)
Needle Nose Pliers
Awl
Scissors
AAAA
AAAA
AAAA
2
Model Aircraft Engine
Muffler
Engine and Muffler
Glow Plug
Wire Cutters
3
Fuel Bottle
Plug Wrench
5
M
ODEL
ENG
INE
FUEL
6
Epoxy A
Epoxy B
Instant Glue
Low Viscosity Type
Epoxy Glue
Glue
4
Purchase a propeller that
will match your engine.
Propeller
Silicone Tube
Vibration Protection Sponge
REQUIRED FOR OPERATION (Purchase separately!)
CAUTION
: For details concerning the equipment listed below
(size, maker, etc.), check with your hobby shop.
TOOLS REQUIRED (Purchase separately!)
CAUTION
: Only use a minimum 4 channel transmitter, configured
for aircraft!
WARNING: Normal gasoline
cannot be used with
glow engines.
2 .40
4 .52~.53
2 Stroke .40
4 Stroke .52 ~ .53
Engine Starter
12V
12V Battery (for starter)
Other equipment for enhancing airplane operation & performance
Spinner Nut
Fuel Filter
7
One-touch Plug Heater Set
2
Extension Lead x 2
(200mm)
1
Y- Harness x 1
Muffler extention
adapter (2 Stroke)
Silicon
Silicon Glue
Others
3
1
BEFORE YOU BEGIN
2
3
Read through the manual before you begin, so you will have an overall idea of what to do.
Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor.
Symbols used throughout this instruction manual, comprise:
Must be purchased separately!
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Cut off excess.Apply epoxy glue.
Assemble left and right sides
the same way.
Apply instant glue
(CA glue, super glue).
Ensure smooth non-binding
movement while assembling.
Do not overlook this
symbol!
Use an iron covered with a cloth!
Start at low setting. Increase the set--
ting if necessary. If it is too high, you
may damage the film.
low setting
with cover (cloth)
The pre-covered film on ARF kits may wrin-kle due
to variations of temperature. Smooth out as
explained right.
Pay close attention here!
Warning!
Tentatively tighten.
2mm
Join lower wing halves together
as for the upper wing(shown
above), being careful to check
dihedral.
Warning!
Apply epoxy glue to wing spar
halves and join together.
When dry, apply epoxy to one end of wing
spar and insert into wing. Wipe away
excess and let dry. Apply fresh glue to other
half of spar and mating surfaces of wing and join.
Secure with tape until dry.
Warning!
4
1
3
2
Lower Main Wing
Lower Main Wing
Carefully apply instant glue to
both sides of the hinge, ensuring
free movement.
Before cutting away the covering film,
lightly heat that area with an iron.
Align the centre of the main
wing with the aileron.
Upper Main Wing
Note the direction.
Top
Dihedral 90mm at wing tip.
If there is a gap, carefully fill with epoxy glue.
Do not disregard this symbol!
Warning!
Pay close attention here!
Apply epoxy glue.
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(CA glue, super glue).
Assemble left and right sides
the same way.
90mm
Wing Underside
Note the direction.
Top
Center Sec.
Cut away only film
Cut away only film
Aileron
Note the direction
90mm
AÕ
A
A = AÕ
5
4
Lower Main Wing
6
Lower Main Wing
5
Lower Main Wing (Upper Side)
2x8mm
Aileron Servo
2mm
Included with the radio set.
Apply epoxy glue.
Cut off shaded portion.
Assemble left and right sides
the same way.
Drill holes with the specified
diameter (here: 2mm).
2mm
Must be purchased separately!
1mm
Cut away only film.
Cut away only film.
4
2 x 20mm
Screw
2 x 20mm
Adjustable Rod (Short)
2x20mm
2 x 8mm
Screw
8
TP
2mm
Wing Under Side
6
7
Lower Main Wing
9
Horizontal Tail (Stabiliser)
8
Lower Wing To Fuselage Join
Carefully apply instant glue to
both sides of the hinge, ensuring
free movement.
3mm
2
4 x 35mm
Screw
2
4 x 12mm
Washer
Drill holes with the specified
diameter (here: 2mm).
2mm
Apply epoxy glue.
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(CA glue, super glue).
Assemble left and right sides
the same way.
Temporarily tighten.
AÕA
A = AÕ
Securely glue together. If the wing separates during
flight, you will lose control of your airplane.
Cut away only film.
Warning!
Do not disregard this symbol!
Warning!
Pay close attention here!
Align with the holes
in the main wing.
4mm
Cut away only film.
4x35mm
Temporarily tighten.
Elevator
Note the direction
2mm
7
10
Vertical Tail
11
Rudder
A
AÕ
B
BÕ
A = AÕ
B = BÕ
Securely glue together. If the wing separates during
flight, you will lose control of your airplane.
Warning!
Securely glue together.
If the wing separates during flight, you will lose
control of your airplane.
Warning!
Carefully apply instant glue to both
sides of the hinge, ensuring free
movement.
Do not overlook this symbol!
Warning!
Drill holes with the specified
diameter (here: 2mm).
2mm
Apply epoxy glue.
Cut off shaded portion.
Apply instant glue
(CA glue, super glue).
Pay close attention here!
Ensure smooth non-binding
movement while assembling.
2mm
Cut away only film.
C = CÕ
C CÕ
Slit here for tail gear.
Note the direction
Rudder
2mm
2mm
Front
Pay close attention here!
Main Landing Gear
8
13
2
3x 3mm
Set Screw
2
4mm
Stoper
Drill holes with the specified
diameter (here: 2mm).
2mm
Cut off shaded portion.
Assemble left and right sides
the same way.
3x12mm
3x12mm
Main Landing Gear
12
Lightly heat the film to be
removed with an iron and
carefully cut away.
14
Fuel Tank
Fix with silicon glue.
Stuff Vibration Protection Sponge.
Remove main wing to install tank.
3x35mm
1
3 x 35mm TP
Screw
3x35mm
5mm
After confirming the direc-tion
(see front view of fuel tank),
insert and tighten the screw.
8
TP Screw
3 x 12mm TP
2mm
Apply instant giue
(CA glue, super glue)
3x 3mm
9
16
Engine Mount
Use a muffler extension adapter.
(purchase separately)
125mm
4
3 x 25mm
Screw
4
4
3mm
Washer
3mm
Spring Washer
4
3mm
Nut
Drill holes with the specified
diameter (here: 2mm).
2mm
Apply epoxy glue.
Pay close attention here!
15
Engine Mount
Depends on
the position
of carburettor.
A
Engine shaft line
5mm
Engine Mount
Spring Washer
3mm
Washer
3mm
3x25mm
A
2
A
2
A
3.1mm
6mm
9mm
6mm
1
3
4
4mm
Mount Nut
4 x 20mm
Screw
A
4 x 10mm
Washer
2
4 x 20mm
4 x 20mm
Must be purchased separately
4.1mm
4 x 10mm
4mm
Cut off shaded portion.
2mm
15mm
10
17
Cowling
18
Linkage Rod
2mm
2mm
Heat-shrink Tube
Adjustable Rod (Long)
Rod
Beware of the flame!
Beware of the flame!
Be careful not to scorch the
heat-shrink tube!
x2
Drill holes with the specified
diameter (here: 2mm).
2mm
Apply epoxy glue.
Cut off shaded portion.
Apply instant glue
(CA glue, super glue).
Pay close attention here!
Assemble as many times as
specified (here: twice).
x
2
Relieve the cowl to clear the engine head.
19
Horizontal / Vertical Tail
3 mm
2x 8mm
2 x 20mm
2 x 20mm
25mm
10mm
10mm
2mm
1mm
2 x 8mm
Screw
5
TP
2mm
4
2 x 20mm
Screw
Must be purchased separately
11
Elevator Rod
Rudder Rod
21
Linkage
20
Linkage
1
Plastic Parts
1
Linkage Stopper
1
Elevator Servo
Rudder Servo
Throttle Servo
3 x 3mm
Set Screw
Must be purchased separately!
Elevator Rod
Rudder Rod
Apply epoxy glue.
Throttle Rod
Plastic Parts
3x3mm
29
In order to obtain the correct center of gravity(CG),
position the servo mount accordingly and fix mount
securely with epoxy glue
Pay close attention here!
ページが読み込まれています...
ページが読み込まれています...
14
27
Decals
Kit includes decals for Royal Air Force and
Swedish Crown markings
26
Receiver / Battery
Carefully install the receiver and battery pack to
ensure that they will not shift during flight.
(After checking CG in step )
Secure foam padding with
rubber bands or tape as required.
Foam Protection
Receiver
Receiver Power Supply
Must be purchased separately!
Do not disregard this symbol!
Warning!
Pay close attention here!
Adjust the travel of each control surface to the values in the diagrams.
These values fit general flight capabilities. Readjust according to your needs and flight level.
15mm
15mm
30mm
30mm
10mm
10mm
RUDDER
ELEVATOR
AILERON
Position for
left diagram.
Position for
left diagram.
29
28
Control Surface Movement
For the correct placement of decals, please refer to the box top
and illustrations below (Some markings are not included)
15
This aircraft has been designed for intermediate to experienced level flyers. First time pilots should seek the advice
of more experienced flyers during construction and for initial flights.
Initially, less experienced pilots should only fly with an experienced pilot, until they become more proficient.
This aircraft is designed to be powered by either a 2 stroke .40 class size engine or a 4 stroke 50class size engine.
Installation of engines other than those specified could to lead to a serious accident and/or damage to property.
Warning!
If necessary, re-position receiver and
battery to get correct C of G.
Check C of G position before flying.
CG
Pay close attention here!
Do not disregard this symbol!
Warning!
Ensure all screws are securely tightened before flight.
Warning!
FOR JAPANESE MARKET ONLY.
No.
11837-01
11837-02
11837-03
11837-04
Cowling
Wing Stay Set
2200 1600
1000
2000
2200
2500
600
3500
200 200
Canopy
Main Gear
No. Part Names Quantity
11837-05
11837-06
11837-07
11441-05
Part Names Quantity
Stay Joint
Decals
Repair Films (Satin Yellow)
SPARE PARTS
x1 N x2
x2
x1 x2
x12
x2
x4
45-55mm
45-55mm
2 4 50
29
Centre of Gravity (C of G)
00
0 0 2 1 0 4 4 7 2 7 1
1 6 8 0
0 0 2 1 0 4
4 7 2 7 1
1 6 8 0
1,400
200
80
1,680
(1)
(2)
(2)
(3)
(4)
(1)
"Kyosho Direct-Mail-Parts-Order-System" is available only for Japanese market
11837
TIGER MOTH 40
OFF
ON
Before Flying
Before flying your airplane, ensure
the airfield is spacious enough.
Always fly it outdoors in safe areas
with no debris or obstacles!
For handling the radio properly,
refer to its instruction manual.
Ensure the spinner and propeller are
securely attached.
If your airplane begins to operate by
itself, there is another transmitter on
your frequency. Immediately stop
your airplane; otherwise you may
lose control of it which will result in
accidents.
Fully extend
the transmitter
antenna.
Switch on the transmitter.
Switch on the receiver.
Ensure the wings are securely
attached.
Flying
Fill the fuel tank.
By moving the control sticks, ensure
all control surfaces moves as per
your adjustments.
For starting the engine, apply low
throttle and hold the engine starter
against the spinner.
Adjust the needle.
After Flying
Only use KYOSHO genuine parts!
Cautions for Safety
Adjust the engine always from behind,
but never from infront or the sides as
a rotating propeller may badly injure
you!
Do not allow watching people to get
too close to a rotating propeller.
Immediately disuse defective pro-
pellers as well as deformed spinners.
If the dry batteries in the radio are
flat, replace them with fresh ones.
Do not fly your airplane above people
standing around.
ON
ON
Hand-launch your airplane into the
wind to make it take off.
Do not fly your airplane when there
is a strong wind or a lateral wind.
Always land your airplane into the
wind.
Bring your airplane to a halt by
lowering the throttle trim.
After each flight, the engine is very
hot. Beware of getting burned!
Wipe away any fuel deposits or dirt.
Never throw burning, gleaming or
smouldering things into fuel cans,
even if these happen to be empty.
This will result in serious injury!
WIND
WIND
OFF
OFF ON
Switch off the receiver.
Switch off the transmitter.
OFF
Draw out the remaining fuel from the
fuel tank and fill it back into the can.
By moving the throttle control
stick, ensure the carburetor opens
and closes without effort.
R
THE FINEST RADIO CONTROL MODELS
62150005-1 PRINTED IN CHINA
Always do observe the following in order to prevent accidents!
FLIGHT MANUAL
Warning!
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
他の言語で
- English: Kyosho TIGER MOTH 40 User manual
関連論文
-
Kyosho AURUM MINIX SPORTS 25 ユーザーマニュアル
-
-
-
-
-
-
-
-
-
