DeWalt DCS356 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル

このマニュアルも適しています

DCS355
DCS356
Final page size: A5 (148mm x 210mm)
B
Copyright DeWALT
English (original instructions) 5
繁体中文 15
한국어 23
1
4
1
3
2
10
DCS356
DCS355
6
7
9
8
11
5
8
9
9
8
XXXX XX XX
25
Fig. A
A
그림 A
Fig. B
B
그림 B
2
3
22
24
23
16 18
12
20
Fig. C
C
그림 C
Fig. D
D
그림 D
Fig. F
F
그림 F
Fig. E
圖 E
그림 E
Fig. G
圖 G
그림 G
3
14
7
1
14
7
7
6
6
7
16
15
21
13
5
6
Fig. H
圖 H
그림 H
Fig. I
圖 I
그림 I
Fig. J
圖 J
그림 J
Fig. K
圖 K
그림 K
Fig. M
圖 M
그림 M
Fig. L
圖 L
그림 L
Fig. N
圖 N
그림 N
4
2
4
1
13
17
15
16
5
21
17
23
17
19
Fig. O
O
그림 O
Fig. Q
Q
그림 Q
Fig. R
R
그림 R
Fig. S
S
그림 S
Fig. P
P
그림 P
ENGLISH
5
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
thesesymbols.
DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
seriousinjury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
seriousinjury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderateinjury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
propertydamage.
Denotes risk of electricshock.
Denotes risk offire.General Power Tool Safety Warnings
DCS355 DCS356
Voltage V
DC
18(20 Max) 18(20 Max)
Battery type Li-Ion Li-Ion
Oscillating frequency min
-1
0–20000 0–20000
Oscillating angle 1.6˚ 1.6˚
Speed 1 min
-1
- 15000
Speed 2 min
-1
- 17000
Speed 3 min
-1
- 20000
Weight (without battery pack) kg 1.1 1.1
WARNING: To reduce the risk of injury, read the
instructionmanual.
English (original instructions)
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough
product development and innovation make DeWALT one of the
most reliable partners for professional power toolusers.
Technical Data
CORDLESS OSCILLATING MULTITOOL
DCS355, DCS356
GENERAL POWER TOOL SAFETY WARNINGS
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
powertool.
1) Work Area Safety
a ) Keep work area clean and well lit. Cluttered or dark
areas inviteaccidents.
b ) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust orfumes.
c ) Keep children and bystanders away while operating
a power tool. Distractions can cause you to losecontrol.
2) Electrical Safety
a ) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electricshock.
b ) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if
your body is earthed orgrounded.
Batteries Chargers/Charge Times (Minutes)
Cat # V
DC
Ah Weight (kg)
DCB104 DCB107 DCB112 DCB113 DCB115 DCB118 DCB132 DCB119
DCB546/DCB606 18/54(20/60 Max) 6.0/2.0 1.05 60 270 170 140 90 60 90 X
DCB547/DCB609 18/54(20/60 Max) 9.0/3.0 1.46 75 420 270 220 135 75 135 X
DCB548/DCB612 18/54(20/60 Max) 12.0/4.0 1.44 120 540 350 300 180 120 180 X
DCB181 18(20 Max) 1.5 0.35 22 70 45 35 22 22 22 45
DCB182/DCB204 18(20 Max) 4.0 0.61 60/40 185 120 100 60 60/40 60 120
DCB183/DCB203 18(20 Max) 2.0 0.40 30 90 60 50 30 30 30 60
DCB184/DCB205 18(20 Max) 5.0 0.62 75/50 240 150 120 75 75/50 75 150
DCB185 18(20 Max) 1.3 0.35 22 60 40 30 22 22 22 X
DCB187 18(20 Max) 3.0 0.54 45 140 90 70 45 45 45 90
DCB189 18(20 Max) 4.0 0.54 60 185 120 100 60 60 60 120
6
ENGLISH
b ) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must berepaired.
c ) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the
power toolaccidentally.
d ) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrainedusers.
e ) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained powertools.
f ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier tocontrol.
g ) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardoussituation.
h ) Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpectedsituations.
5) Battery Tool Use and Care
a ) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another batterypack.
b ) Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury andfire.
c ) When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or afire.
d ) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation orburns.
e ) Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk
of injury.
f ) Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or temperature
above 130 °C may causeexplosion.
c ) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electricshock.
d ) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electricshock.
e ) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electricshock.
f ) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electricshock.
3) Personal Safety
a ) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personalinjury.
b ) Use personal protective equipment. Always wear eye
protection. Protective equipment such as a dust mask,
non-skid safety shoes, hard hat or hearing protection used
for appropriate conditions will reduce personalinjuries.
c ) Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invitesaccidents.
d ) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in
personalinjury.
e ) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpectedsituations.
f ) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair can be
caught in movingparts.
g ) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-relatedhazards.
h ) Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause severe
injury within a fraction of asecond.
4) Power Tool Use and Care
a ) Do not force the power tool. Use the correct power
tool for your application. The correct power tool
will do the job better and safer at the rate for which it
wasdesigned.
7
ENGLISH
g ) Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging
improperly or at temperatures outside the specified range
may damage the battery and increase the risk of fire.
6) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
b ) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
Additional Safety Rules for Oscillating
Multi‑Tool
WARNING: Take special care when sanding some woods
(e.g. beech, oak) and metal which may produce toxic dust.
Wear a dust mask specifically designed for protection
against toxic dust and fumes and ensure that persons
within or entering the work area are alsoprotected.
WARNING: Use this tool in a well-ventilated area when
sanding ferrous metals. Do not operate the tool near
flammable liquids, gases or dust. Sparks or hot particles
from sanding or arcing motor brushes may ignite
combustiblematerials.
Sanding Paint
WARNING: Observe the applicable regulations for
sanding paint. Pay special attention to the following:
Whenever possible, use a vacuum extractor for dustcollection.
Take special care when sanding paint which is possibly
lead based:
ʵ Do not let children or pregnant women enter the
workarea.
ʵ All persons entering the work area should wear a mask
specially designed for protection against lead paint dust
andfumes.
ʵ Do not eat, drink or smoke in the workarea.
Dispose of dust particles and any other removal debrissafely.
Hold power tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a "live"
wire will make exposed metal parts of the tool "live" and shock
theoperator.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and may
lead to loss ofcontrol.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
Impairment ofhearing.
Risk of personal injury due to flyingparticles.
Risk of burns due to accessories becoming hot
duringoperation.
Risk of personal injury due to prolongeduse.
SAVE THESE INSTRUCTIONS
Chargers
DeWALT chargers require no adjustment and are designed to be
as easy as possible tooperate.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
your charger corresponds to that of yourmains.
Your DeWALT charger is double insulated in
accordance with IEC60335; therefore no earth wire
isrequired.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the
DeWALT
serviceorganisation.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1mm
2
; the maximum length
is30m.
When using a cable reel, always unwind the cablecompletely.
Important Safety Instructions for All Battery
Chargers
SAVE THESE INSTRUCTIONS: This manual contains important
safety and operating instructions for compatible battery
chargers (refer to TechnicalData).
Before using charger, read all instructions and cautionary
markings on charger, battery pack, and product using
batterypack.
WARNING: Shock hazard. Do not allow any liquid to get
inside charger. Electric shock mayresult.
WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA orless.
CAUTION: Burn hazard. To reduce the risk of injury,
charge only
DeWALT rechargeable batteries. Other types of
batteries may burst causing personal injury anddamage.
CAUTION: Children should be supervised to ensure that
they do not play with theappliance.
NOTICE: Under certain conditions, with the charger
plugged into the power supply, the exposed charging
contacts inside the charger can be shorted by foreign
material. Foreign materials of a conductive nature such as,
but not limited to, steel wool, aluminum foil or any buildup
of metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply
when there is no battery pack in the cavity. Unplug charger
before attempting to clean
8
ENGLISH
DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual. The charger
and battery pack are specifically designed to worktogether.
These chargers are not intended for any uses other than
charging
DeWALT rechargeable batteries. Any other uses
may result in risk of fire, electric shock orelectrocution.
Do not expose charger to rain orsnow.
Pull by plug rather than cord when disconnecting
charger. This will reduce risk ofdamage to electric plug
andcord.
Make sure that cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage orstress.
Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result in risk
of fire,electric shock, orelectrocution.
Do not place any object on top of charger or place
the charger on a soft surface that might block the
ventilation slots and result in excessive internal heat.
Place the charger in a position away from any heat source. The
charger is ventilated through slots in the top and the bottom
of thehousing.
Do not operate charger with damaged cord or plug—
have them replacedimmediately.
Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way. Take it
to an authorised servicecentre.
Do not disassemble charger; take it to an authorised
service centre when service or repair is required. Incorrect
reassembly may result in a risk of electric shock, electrocution
orfire.
In case of damaged power supply cord the supply cord must
be replaced immediately by the manufacturer, its service agent
or similar qualified person to prevent anyhazard.
Disconnect the charger from the outlet before
attempting any cleaning. This will reduce the risk of
electric shock. Removing the battery pack will not reduce
thisrisk.
NEVER attempt to connect two chargerstogether.
The charger is designed to operate on standard 220-
240V household electrical power. Do not attempt to
use it on any other voltage. This does not apply to the
vehicularcharger.
Charging a Battery (Fig. B)
1. Plug the charger into an appropriate outlet before inserting
battery pack.
2. Insert the battery pack
1
into the charger, making sure the
battery pack is fully seated in the charger. The red (charging)
light will blink repeatedly indicating that the charging
process has started.
3. The completion of charge will be indicated by the red
light remaining ON continuously. The battery pack is fully
charged and may be used at this time or left in the charger.
To remove the battery pack from the charger, push the
battery release button
2
on the battery pack.
NOTE: To ensure maximum performance and life of lithium-ion
battery packs, charge the battery pack fully before first use.
Charger Operation
Refer to the indicators below for the charge status of the
batterypack.
Charge Indicators
Charging
Fully Charged
Hot/Cold Pack Delay*
* The red light will continue to blink, but a yellow indicator light
will be illuminated during this operation. Once the battery pack
has reached an appropriate temperature, the yellow light will
turn off and the charger will resume the charging procedure.
The compatible charger(s) will not charge a faulty battery pack.
The charger will indicate faulty battery by refusing to light.
NOTE: This could also mean a problem with a charger.
If the charger indicates a problem, take the charger and battery
pack to be tested at an authorised service centre.
Hot/Cold Pack Delay
When the charger detects a battery pack that is too hot or too
cold, it automatically starts a Hot/Cold Pack Delay, suspending
charging until the battery pack has reached an appropriate
temperature. The charger then automatically switches to the
pack charging mode. This feature ensures maximum battery
pack life.
A cold battery pack will charge at a slower rate than a warm
battery pack. The battery pack will charge at that slower rate
throughout the entire charging cycle and will not return to
maximum charge rate even if the battery pack warms.
The DCB118 charger is equipped with an internal fan designed
to cool the battery pack. The fan will turn on automatically when
the battery pack needs to be cooled. Never operate the charger
if the fan does not operate properly or if ventilation slots are
blocked. Do not permit foreign objects to enter the interior of
the charger.
Electronic Protection System
XR Li-Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deep discharge.
The tool will automatically turn off if the Electronic Protection
System engages. If this occurs, place the lithium-ion battery
pack on the charger until it is fully charged.
Wall Mounting
These chargers are designed to be wall mountable or to sit
upright on a table or work surface. If wall mounting, locate the
charger within reach of an electrical outlet, and away from a
corner or other obstructions which may impede air flow. Use
the back of the charger as a template for the location of the
mounting screws on the wall. Mount the charger securely using
drywall screws (purchased separately) at least 25.4mm long
with a screw head diameter of 7–9mm, screwed into wood to
9
ENGLISH
damaged in any way (i.e., pierced with a nail, hit with
a hammer, stepped on). Electric shock or electrocution
may result. Damaged battery packs should be returned to
service centre for recycling.
WARNING: Fire hazard. Do not store or carry the
battery pack so that metal objects can contact
exposed battery terminals. For example, do not place
the battery pack in aprons, pockets, tool boxes, product kit
boxes, drawers, etc., with loose nails, screws, keys, etc.
CAUTION: When not in use, place tool on its side on
a stable surface where it will not cause a tripping
or falling hazard. Some tools with large battery packs
will stand upright on the battery pack but may be easily
knocked over.
Transportation
WARNING: Fire hazard. Transporting batteries can
possibly cause fire if the battery terminals inadvertently
come in contact with conductive materials. When
transporting batteries, make sure that the battery
terminals are protected and well insulated from
materials that could contact them and cause a short
circuit. NOTE: Lithium-ion batteries should not be put in
checkedbaggage.
DeWALT batteries comply with all applicable shipping
regulations as prescribed by industry and legal standards which
include UN Recommendations on the Transport of Dangerous
Goods; International Air Transport Association (IATA) Dangerous
Goods Regulations, International Maritime Dangerous Goods
(IMDG) Regulations, and the European Agreement Concerning
The International Carriage of Dangerous Goods by Road (ADR).
Lithium-ion cells and batteries have been tested to section 38.3
of the UN Recommendations on the Transport of Dangerous
Goods Manual of Tests and Criteria.
In most instances, shipping a
DeWALT battery pack will be
excepted from being classified as a fully regulated Class 9
Hazardous Material. In general, only shipments containing a
lithium-ion battery with an energy rating greater than 100 Watt
Hours (Wh) will require being shipped as fully regulated Class 9.
All lithium-ion batteries have the Watt Hour rating marked on
the pack. Furthermore, due to regulation complexities,
DeWALT
does not recommend air shipping lithium-ion battery packs
alone regardless of Watt Hour rating. Shipments of tools with
batteries (combo kits) can be air shipped as excepted if the Watt
Hour rating of the battery pack is no greater than 100 Whr.
Regardless of whether a shipment is considered excepted
or fully regulated, it is the shipper's responsibility to consult
the latest regulations for packaging, labeling/marking and
documentation requirements.
The information provided in this section of the manual is
provided in good faith and believed to be accurate at the time
the document was created. However, no warranty, expressed or
implied, is given. It is the buyer’s responsibility to ensure that its
activities comply with the applicable regulations.
Transporting the FLEXVOLT
TM
Battery
an optimal depth leaving approximately 5.5mm of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using a
cloth or soft non-metallic brush. Do not use water or any
cleaning solutions. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
Battery Packs
Important Safety Instructions for All Battery
Packs
When ordering replacement battery packs, be sure to include
catalogue number and voltage.
The battery pack is not fully charged out of the carton. Before
using the battery pack and charger, read the safety instructions
below. Then follow charging procedures outlined.
READ ALL INSTRUCTIONS
Do not charge or use battery in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Inserting or removing the battery from the charger may
ignite the dust or fumes.
Never force battery pack into charger. Do not modify
battery pack in any way to fit into a non-compatible
charger as battery pack may rupture causing serious
personal injury.
Charge the battery packs only in
DeWALT chargers.
DO NOT splash or immerse in water or other liquids.
Do not store or use the tool and battery pack in
locations where the temperature may reach or exceed
40 ˚C (104 ˚F) (such as outside sheds or metal buildings
in summer).
Do not incinerate the battery pack even if it is severely
damaged or is completely worn out. The battery pack can
explode in a fire. Toxic fumes and materials are created when
lithium-ion battery packs are burned.
If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If
battery liquid gets into the eye, rinse water over the open eye
for 15 minutes or until irritation ceases. If medical attention
is needed, the battery electrolyte is composed of a mixture of
liquid organic carbonates and lithium salts.
Contents of opened battery cells may cause respiratory
irritation. Provide fresh air. If symptoms persists, seek
medicalattention.
WARNING: Burn hazard. Battery liquid may be flammable
if exposed to spark or flame.
WARNING: Never attempt to open the battery pack for
any reason. If battery pack case is cracked or damaged,
do not insert into charger. Do not crush, drop or damage
battery pack. Do not use a battery pack or charger that
has received a sharp blow, been dropped, run over or
10
ENGLISH
The
DeWALT FLEXVOLT
TM
battery has two modes: Use and
Transport.
Use Mode: When the FLEXVOLT
TM
battery stands alone or is
in a
DeWALT 18V (20V MAX) product, it will operate as an 18V
(20V MAX) battery. When the FLEXVOLT
TM
battery is in a 54V
(60V MAX)or a 108V (120V MAX) (two 54V (60V MAX) batteries)
product, it will operate as a 54V (60V MAX) battery.
Transport Mode: When the cap is attached to the FLEXVOLT
TM
battery, the battery is in Transport mode. Keep the cap for
shipping.
When in Transport mode, strings
of cells are electrically
disconnected within the pack
resulting in 3 batteries with a
lower Watt hour (Wh) rating as compared to 1 battery with a
higher Watt hour rating. This increased quantity of 3 batteries
with the lower Watt hour rating can exempt the pack from
certain shipping regulations that are imposed upon the higher
Watt hour batteries.
For example, the Transport
Wh rating might indicate
3x36 Wh, meaning 3
batteries of 36 Wh each.
The Use Wh rating might
indicate 108Wh (1battery implied).
Storage Recommendations
1. The best storage place is one that is cool and dry away
from direct sunlight and excess heat or cold. For optimum
battery performance and life, store battery packs at room
temperature when not in use.
2. For long storage, it is recommended to store a fully charged
battery pack in a cool, dry place out of the charger for
optimal results.
NOTE: Battery packs should not be stored completely depleted
of charge. The battery pack will need to be recharged before
use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the labels
on the charger and the battery pack may show the following
pictographs:
Read instruction manual before use.
See Technical Data for charging time.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Example of Use and Transport Label Marking
Do not expose to water.
Have defective cords replaced immediately.
Charge only between 4 ˚C and 40 ˚C.
Only for indoor use.
Discard the battery pack with due care for the
environment.
Charge DeWALT battery packs only with designated
DeWALT chargers. Charging battery packs other
than the designated
DeWALT batteries with a
DeWALT charger may make them burst or lead to
other dangerous situations.
Do not incinerate the battery pack.
USE (without transport cap). Example: Wh rating
indicates 108 Wh (1 battery with 108 Wh).
TRANSPORT (with built-in transport cap). Example:
Wh rating indicates 3 x 36 Wh (3batteries of 36 Wh).
Battery Type
The DCS355, DCS356 operate on a 18 volt (20V Max) battery
pack.
These battery packs may be used: DCB181, DCB182, DCB204,
DCB183, DCB203, DCB184, DCB205, DCB185, DCB187, DCB189,
DCB546, DCB606, DCB547, DCB609, DCB548, DCB612. Refer to
Technical Data for moreinformation.
Package Contents
The package contains:
1 Adaptor for all blades
1 31mm x 43mm Fastcut wood blade
1 Sanding-pad
1 31 mm x 43 mm Wood with nails blade
1 Rigid scraper blade**
1 Blade adaptor hex key
1 Dust extraction adaptor**
1 Cutting guide**
1 100mm Semicircle blade**
25 Assorted sandpaper pieces
1 9.5mm x 43mm Wood detail blade**
1 3mm Carbide grout removal blade (100mm half moon)**
1 Cutting guide hex key**
1 Charger
1 TSTAK kitbox
1 Li-Ion battery pack (C1, D1, L1, M1, P1, S1, T1, X1, Y1 models)
2 Li-Ion battery packs (C2, D2, L2, M2, P2, S2, T2, X2, Y2 models)
3 Li-Ion battery packs (C3, D3, L3, M3, P3, S3, T3, X3, Y3 models)
11
ENGLISH
1 Instruction manual
** Accessory included only with NT models and kits containing
battery andcharger.
NOTE: Battery packs, chargers and kitboxes are not included
with N models. Battery packs and chargers are not included with
NT models. Bmodels include Bluetooth® batterypacks.
NOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by
DeWALT is under license. Other trademarks and
trade names are those of their respectiveowners.
Check for damage to the tool, parts or accessories which may
have occurred duringtransport.
Take the time to thoroughly read and understand this manual
prior tooperation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Visible radiation. Do not stare into light.
Date Code Position (Fig. B)
The date code
25
, which also includes the year of manufacture,
is printed into thehousing.
Example:
2020 XX XX
Year of Manufacture
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury couldresult.
1
Variable speed trigger
2
LED Worklight
3
Accessory clamp lever
4
Lock on/off button
5
Accessory side mount slots
6
Cut guide block
7
Cut guide arm
8
Battery pack
9
Battery release button
10
Speed selector (DCS356)
Intended Use
This oscillating multi-tool is designed for professional detail
sanding, plunge cutting, flush cutting, removal of excess
materials and surface preparationapplications.
DO NOT use under wet conditions or in the presence of
flammable liquids orgases.
This oscillating multi-tool is a professional powertool.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
Young children and the infirm. This appliance is not
intended for use by
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can causeinjury.
WARNING: Use only DeWALT battery packs andchargers.
WARNING: Risk of lacerations or burns. Do not touch
the sharp edges of accessories at any time. Do not
touch workpiece or blade immediately after operating the
tool. They can become very hot. Handle carefully. Always
allow accessories and workpiece to cool beforehandling.
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
NOTE: Make sure your battery pack
1
is fullycharged.
To Install the Battery Pack into the Tool Handle
1. Align the battery pack
1
with the rails inside the tool’s
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap intoplace.
To Remove the Battery Pack from the Tool
1. Press the release button
2
and firmly pull the battery pack
out of the toolhandle.
2. Insert battery pack into the charger as described in the
charger section of thismanual.
Fuel Gauge Battery Packs (Fig. B)
Some DeWALT battery packs include a fuel gauge which
consists of three green LED lights that indicate the level of
charge remaining in the batterypack.
To actuate the fuel gauge, press and hold the fuel gauge
button
11
. A combination of the three green LED lights will
illuminate designating the level of charge left. When the level of
charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to berecharged.
NOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-userapplication.
12
ENGLISH
NOTE: The depth/cut guide can be attached to either side
of thetool.
2. Secure the block to the main body with the supplied
screw
15
and washer
21
. Tighten with the supplied hex
wrench
16
.
Depth Guide (Fig. I, J)
This feature allows you to precisely cut material at a
specifieddepth.
1. Insert the guide arm
7
as shown in FigureI into the front
slot on the guide block
6
.
2. Adjust the length of the guide by pulling out or pushing
inward to achieve the desired cut depth as shown in
FigureJ.
3. Secure the guide in place by turning the depth/cut
adjustment knob
14
clockwise. To release the guide turn
the depth/cut adjustment knobcounterclockwise.
Cut Guide (Fig. K–M)
This feature allows you to more accurately track a marked
cutline.
1. Insert the guide arm
7
as shown in FigureK into the slots
on the left and right sides of the guide block
6
.
2. Adjust the length of the guide by pulling out or pushing
inward to achieve the desired length as shown in FigureL.
3. Secure the guide in place by turning the depth/cut
adjustment knob
14
clockwise. To release the guide turn
the depth/cut adjustment knobcounterclockwise.
NOTE: The guide arm can also be placed in the guard assembly
vertically in order to set the height off a cut. Refer to FigureM.
Attaching the Dust Extraction Adaptor
(Fig. Q)
The Dust Extraction Adaptor allows you to connect the tool to
an external dust extractor, either using the AirLock™ system
(DWV9000-XJ), or a standard 35mm dust extractorfitment.
1. Attach the dust extraction adaptor
17
by inserting the
tabs
13
in to the accessory side mount slots
5
.
NOTE: The dust extraction adaptor can be attached to either
side of thetool.
2. Insert screw
15
and washer
21
into the dust extraction
adaptor
17
and tighten with the supplied hex wrench
16
.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicableregulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
WARNING: Ensure switch is fully OFF before installing
thebattery.
Installing/Removing Accessories (Fig. C–M,Q)
Tool-free Accessory clamp (Fig.C–E)
The DCS355, DCS356 features a quick change accessory system.
This allows for faster accessory changes without the need for
wrenches or hex keys like other oscillating toolsystems.
1. Grasp the tool and squeeze the accessory clamping lever
3
as shown in FigureC.
2. Clean any residual debris from the tool shaft and the
accessoryholder.
3. Slide the accessory between the shaft
22
and the accessory
holder making sure the accessory engages all eight pins on
the holder and is flush with the shaft. Ensure the accessory is
oriented as shown in FigureD.
4. Release the accessory clamplever.
NOTE: Some accessories, such as scrapers and blades can be
mounted at an angle if required as shown in FigureE.
Installing/Removing Sanding Sheets (Fig.F)
A diamond shaped platen uses a hook and loop adhesion
system to attach the sanding sheets. The platen allows you to
use it on large flat surfaces and tight spots orcorners.
1. Attach the sanding platen
23
as described under
Installing/RemovingAccessories.
2. Align the edges on the sanding sheet, with the edge of
the sanding platen and press the sanding sheet
24
onto
theplaten.
3. Firmly press the base with the sanding sheet attached
against a flat surface and briefly switch the tool on. This
provides for good adhesion between the platen and the
sanding sheet and also helps to prevent prematurewear.
4. When the tip of the sanding sheet becomes worn, detach
the sheet from the platen, rotate andreapply.
Attaching Accessories Using the Universal
Adapter (Fig.G)
CAUTION: To avoid injury, do not use any accessory
for an application where the adaptor may fail to hold
theaccessory.
CAUTION: Read and follow all manufacturers' safety
warnings for any accessories used with thistool.
CAUTION: To avoid injury, ensure adaptor and accessory
are securelytightened.
Non-
DeWALT accessories can be attached using the
universaladaptor.
1. Place the washer
20
on thetool.
2. Place accessory
12
on towasher.
3. Tighten and secure adaptor nut
18
using hex wrench
16
.
Attaching the Cut Guide (Fig. H–M)
The depth/cut guide allows you to precisely cut material at a
specified depth and more accurately track a marked cutline.
1. Attach the cut guide block
6
by inserting the accessory
tabs
13
on the guide into the accessory side mount slots
5
on the main body of thetool.
13
ENGLISH
2. Push dust extraction arm
19
into the lower aperture of the
dust extraction adaptor
17
.
3. Attach plunge cutting blade as described under Installing/
RemovingAccessories.
4. Adjust the dust extraction arm
19
for bestresults.
Helpful Hints
Always ensure the workpiece is firmly held or clamped to
prevent movement. Any movement of the material may
affect the quality of the cutting or sandingfinish.
Do not start sanding without having the sandpaper
attached to sandingplaten.
Use coarse grit paper to sand rough surfaces, medium grit
for smooth surfaces and fine grit for the finishing surfaces. If
necessary, first make a test run on scrapmaterial.
Excessive force will reduce the working efficiency and cause
motor overload. Replacing the accessory regularly will
maintain optimum workingefficiency.
Do not allow the sandpaper to wear away, it will damage
the sandingpad.
If the tool overheats, especially when used at low speed,
set the speed to maximum and run it with no load for 2–3
minutes to cool the motor. Avoid prolonged usage at very
low speeds. Always keep the bladesharp.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regularcleaning.
WARNING:To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are notserviceable.
Lubrication
Your power tool requires no additionallubrication.
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Proper Hand Position (Fig. N)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Proper hand position requires the tool to be held as shown in
FigureN.
Instructions for Use (Fig. A)
1. Install the batterypack.
2. To turn the tool ON, hold it as shown in FigureN and press
the variable speed trigger
1
.
NOTE: The further the trigger switch is depressed the faster
the tool will operate. If in doubt about the proper speed
for your operation, test the performance at low speed and
gradually increase until a comfortable speed isfound.
3. To turn the tool OFF, release the variable speed trigger
1
.
Lock on/off Button (Fig. O)
The tool can be locked off by fully depressing the lock on/off
button
4
shown in FigureO.
For more comfort in extended use applications, the lock
on/off button
4
can lock the trigger trigger
1
in the
depressedposition.
NOTE: The tool will automatically shut off after operating for
five minutes with the lock-on button engaged. To restart the
tool, the user will have to release the trigger and repress lock-
onbutton.
Speed Selector (Fig. A)
DCS356
Your tool is equipped with a speed selector
10
which allows
you to select one of the three speeds that limits the full speed.
Select the speed based on the application and control the speed
of the tool using the variable speed trigger switch
1
.
LED Worklight (Fig. P)
The LED worklight
2
will activate when the trigger is depressed.
It will automatically shut off following a short period of time
once the trigger isreleased.
Using the Dust Extraction Adaptor with the
Sanding Platen (Fig. R)
1. Attach the dust extraction adaptor
17
. Refer to Attaching
the Dust ExtractionAdaptor.
2. Attach the sanding platen
23
as described under
Installing/RemovingAccessories.
3. Attach sanding sheet as described under Installing/
Removing SandingSheets.
Using the Dust Extraction Adaptor with
Plunge Cutting Accessory (Fig. S)
1. Attach the dust extraction adaptor. Refer to Attaching the
Dust ExtractionAdaptor.
14
ENGLISH
Optional Accessories
WARNING: Since accessories, other than those offered
by DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only
DeWALT recommended
accessories should be used with thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Compatible accessories
Oscillating sanding pad
Oscillating wood w/ nails blade
Wide titanium oscillating wood w/ nails blade
Oscillating hardwood blade
Oscillating fastcut wood blade
Wide oscillating fastcut wood blade
Oscillating wood detail blade
Oscillating titanium metal blade
Oscillating semicircle blade
Oscillating titanium semicircle blade
Oscillating flush cut blade
Titanium oscillating flush cut blade
Oscillating multi-material blade
Oscillating rigid scraper blade
Oscillating flexible scraper blade
Oscillating carbide grout removal blade
Oscillating fastcut carbide grout removal blade
Oscillating carbide rasp
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
householdwaste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
Run the battery pack down completely, then remove it from
the tool.
Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
繁體中文
1515
恭喜!
感謝您選購 DeWALT 工具。憑藉多年的經驗、完善的產品開發與創
新,
DeWALT 已成為專業電動工具使用者最可靠的合作夥伴之一。
請注意!各地區上市產品/配件不盡相同請依台灣繁體中文說明書
的內容為主。
注意:
12V MAx 為最大初始電池電壓 (無負載測量)標稱電壓為
10.8V
技術資料
警告:為了降低受傷的風險必須仔細閱讀使用手冊。
定義:安全指南
以下定義描述了每一個詞彙的嚴重程度。請閱讀本手冊並注意這
些符號。
危險:表示緊急危險狀況若未能避免導致死亡
重傷害
警告:表示潛在危險情況若未能避免可能導致死亡
重傷害。
小心:表示潛在危險情況若未能避免可能導致輕微
度傷害
注意:表示一種非人身傷害的行為若未能避免可能導致
財產損失
表示觸電危險。
表示火災危險。
DCS355 DCS356
電壓
V
DC
18(20 Max) 18(20 Max)
電池類型 鋰離子 鋰離子
震盪频率
min
-1
0–20000 0–20000
震盪角度
1.6˚ 1.6˚
速度 1
min
-1
- 15000
速度 2
min
-1
- 17000
速度 3
min
-1
- 20000
重量(不包括電池)
kg 1.1 1.1
無碳刷磨切機
DCS355, DCS356
電動工具一般安全警告
警告!請閱讀安全警告及所有指示。不遵循下列的這些警告
和指示可能會導致觸電、火災及/或嚴重傷害。
請保存所有警告與指示以備將來查閱。
以下列示所有警告中的術語「電動工具」是指電源驅動(插電)電動
工具或電池驅動(充電)電動工具。
1工作場地安全
a )
請保持工作場地清潔明亮。混亂或黑暗的場地會引發事故。
b )
請勿在易爆環境如有易燃液體、氣體或粉塵的環境中操作
電動工具。電動工具產生的火花可能會引燃粉塵或煙霧。
c )
請等待兒童和旁觀者離開之後才操縱電動工具。分心會導
致您疏於控制。
2電氣安全
a )
電動工具插頭必須與插座相符。切勿以任何方式改裝插頭。
需接地的電動工具不能使用任何配接器插頭。使用未經改
裝的插頭與相符的插座可降低觸電風險。
b )
避免人體接觸接地表面如管道、散熱片、爐灶和冰箱。若您
的身體接地會提高觸電的風險。
c )
不得將電動工具暴露在雨中或潮濕環境中。水進入電動工
具會提高觸電風險。
d )
切勿濫用電線。請勿使用電線來搬運、拉動電動工具或拔出
插頭。讓電線遠離熱、油、銳邊和活動部件。受損或纏繞的電
線會增加觸電危險。
e )
若要在戶外使用電動工具請使用適合戶外使用的延長電
線。採用適合室外使用的電線可降低觸電危險
電池
充電器/充電時間(分鐘)
目錄號 伏特
直流
安時 重量 (kg)
DCB104 DCB107 DCB112 DCB113 DCB115 DCB118 DCB132 DCB119
DCB546/DCB606 18/54(20/60 Max) 6.0/2.0 1.05 60 270 170 140 90 60 90 X
DCB547/DCB609 18/54(20/60 Max) 9.0/3.0 1.46 75 420 270 220 135 75 135 X
DCB548/DCB612 18/54(20/60 Max) 12.0/4.0 1.44 120 540 350 300 180 120 180 X
DCB181 18(20 Max) 1.5 0.35 22 70 45 35 22 22 22 45
DCB182/DCB204 18(20 Max) 4.0 0.61 60/40 185 120 100 60 60/40 60 120
DCB183/DCB203 18(20 Max) 2.0 0.40 30 90 60 50 30 30 30 60
DCB184/DCB205 18(20 Max) 5.0 0.62 75/50 240 150 120 75 75/50 75 150
DCB185 18(20 Max) 1.3 0.35 22 60 40 30 22 22 22 X
DCB187 18(20 Max) 3.0 0.54 45 140 90 70 45 45 45 90
DCB189 18(20 Max) 4.0 0.54 60 185 120 100 60 60 60 120
繁體中文
1616
f )
若必須在潮濕環境中操作電動工具請使用受漏電保護器
(RCD) 保護的電源供應器。使用RCD可降低觸電風險。
3人身安全
a )
保持警覺;在操作電動工具時請留意所執行的操作並按照
一般的程式執行。請勿在疲倦或在受到毒品、酒精或藥品的
影響時使用電動工具。操作電動工具時一時的注意力分散
可能會導致嚴重人身傷害。
b )
使用個人防護裝置。始終佩戴護目裝置。防護設備 (例如在
適當條件下使用的防塵面具、防滑安全鞋、安全帽或聽力保
護裝置) 可減少人身傷害。
c )
避免意外啟動。連接電源及/或電池組、舉抬或搬運電動工
具之前請確定開關處於關閉位置。若搬運電動工具時將手
指放在開關上或者在電動工具開關開啟時將插頭插入電
源插座這兩種行為都會引發事故。
d )
啟動電動工具之前請卸下所有的調整鑰匙或扳手。遺留在
電動工具旋轉部件上的扳手或鑰匙會導致人身傷害。
e )
不要過度伸張雙手。時刻注意腳下與身體的平衡。如此可在
意外情況下更好地控制電動工具。
f )
適當穿著。請勿穿寬鬆衣服或佩戴飾品。讓您的頭髮、衣服
和手套遠離活動部件。寬鬆衣服、佩飾或長髮可能會捲入
活動部件中。
g )
若配備用於連接排屑裝置、集塵設備的裝置請確定正確
連接和使用這些裝置。使用集塵設備可減少與粉塵有關
的危險。
h )
請勿因頻繁使用而對工具特別熟悉讓你變得自滿而忽略
工具的安全原則。粗心操作可以在片刻間造成嚴重傷害。
4)電動工具的使用與注意事項
a )
請勿超負荷使用電動工具。請根據您的應用使用正確的電
動工具。若使用的電動工具正確無誤該工具能以設計額定
值更有效、更安全地執行工作。
b )
若開關不能開啟或關閉電源切勿使用該電動工具。若開關
無法控制電動工具則電動工具存在危險必須予以維修。
c )
在執行任何調整、更換配件或儲存工具之前必須從電源上
拔掉插頭及/或卸下電池組。此類防護性安全措施可降低電
動工具意外啟動的風險。
d )
將閒置的電動工具儲存在兒童無法接觸的地方並且不要
讓不熟悉電動工具或對這些使用指示不瞭解的人員操作電
動工具。未經訓練的使用者操作電動工具會發生危險。
e )
維護電動工具。檢查活動部件是否對準或卡住、是否存在任
何破損情況或任何能影響電動工具運行的其他情況。若有
損毀必須在使用之前修理電動工具。許多事故都是由於電
動工具欠缺維護所導致。
f )
保持切削工具鋒利和清潔。妥善維護、刀刃鋒利的刀具卡住
的可能性更低更易於控制。
g )
使用電動工具、配件和工具刀頭等時請遵循這些指示使
且指示須包含工作環境和所要執行工作的注意事項。
使用電動工具執行與設計用途不相符的操作會導致危險。
h )
手柄和抓握表面都應保持乾燥、清潔及遠離油脂。光滑手
柄和抓握表面不便於在意外情況下對工具進行安全處理
與控制。
5)電池工具的使用與注意事項
a )
只能使用製造廠商指定的充電器為電池充電使用僅適
合一種電池組的充電器為其他類型的電池組充電會導致
火災危險。
b )
請使用原廠的電動工具電池組使用其他非原廠的電池組
會導致人身傷害和火災危險。
c )
不使用電池組時請將其遠離如迴紋針、硬幣、鑰匙、釘子、
螺絲以及其他可連通電池兩極的金屬物品。將電池兩極短
路會導致灼傷或火災。
d )
濫用電池的情況下液體會從電池中噴出;避免與液體接
觸。若不小心接觸液體請用清水沖洗。若液體噴濺到眼睛
沖洗之後還要進行治療。從電池噴出的液體會刺激皮
膚或造成灼傷。
e )
請勿使用已經損壞或改動的電池組或工具。損壞或改動
的電池可能表現出不可預計的行為導致火災、爆炸或傷
害風險。
f )
請勿讓電池組或工具暴露於火中或過高溫度的環境中。
露於火中或溫度超過 130°C的環境中可能導致爆炸。
g )
請遵循所有充電說明請勿在說明中規定的溫度範圍以外
的環境對電池組或工具充電。不當或在指定範圍以外的溫
度下充電可能導致電池損壞並增加火災風險。
6)檢修
a )
本電動工具必須由合格的維修人員並只採用相同的原廠零
件來執行檢修。這將確保電動工具的安全性。
b )
切勿維修損毀的電池組。電池組的維修應僅由製造商或授
權服務提供商執行。
震盪多功能工具的额外安全說明
警告:在打磨一些木材(例如山毛櫸、橡木和金屬時,需格
外小心。這種操作可能會產生有毒粉塵。要穿戴為防止有毒
塵煙而專門設計的防塵面具同時確保位於或進入作業區
域內的人員也要採取防護措施。
警告:在打磨含鐵金屬時要在通風良好的區域使用本工
具。請勿在易燃液體、氣體或粉塵附近使用該工具。由打
磨或電弧電刷而產生的火花或高溫顆粒可能會引燃可燃
材料。
砂光漆
警告:砂光漆的適用規定。尤其注意以下幾點:
如有可能使用真空提取器收集粉塵。
在砂時需要多加注意油漆可能含鉛:
ʵ
兒童和孕婦不得進入作業區。
ʵ
所有進入作業區的人員均應佩戴為防止含鉛油漆塵煙而專
門設計的防塵面具。
ʵ
請勿在作業區內進食、飲水或吸煙。
以安全的方式丟棄粉塵顆粒和任何其他可移除的殘渣。
在切削配件或緊固件可能觸及暗線或工具自身線纜之處進
行操作時要通過絕緣握持面來握持電動工具。如果接觸
“帶電”導線工具金屬部件表面就會“帶電”並使操作人
員觸電。
使用夾具或其他實用方式進行固定為工件提供一個穩固
平台。用手握住或用身體抵住工件都會讓工件變得不穩定
從而失控。
剩餘風險
即使應用有關的安全規定並採用安全設備仍然還有一些無法避免
的剩餘風險。此類風險包括:
聽力受損。
繁體中文
1717
飛散的顆粒引起的人身傷害風險。
操作過程中配件變熱引起的灼傷風險。
長時間使用引起的人身傷害風險。
請保存這些安全指示
充電器
DeWALT 充電器無需調節專為盡可能輕鬆使用而設計。
電氣安全
電動馬達只適用一種電壓。請務必檢查電池組電壓是否與銘牌
並且確保充電器的電壓與電源電壓一致。
DeWALT 充電器符合 IEC60335 雙重絕緣要求因此無需使
用接地線。
若電源線損壞必須使用
DeWALT 維修機構提供的專用電線進行
使用延長電纜
如非絕對必要否則不要使用延長電線。請使用與充電器的輸入功
率相配的認可延長電纜(請參閱
技術資料
導電體的最小橫截面尺
寸為 1 平方公釐最長為 30 米。
使用電纜捲筒時每次必須把電纜完全展開。
所有電池充電器之重要安全指示
請妥善保管好這些說明:
本手冊包含重要的相容電池充電器安全和
操作說明(請參閱
技術資料
)。
在使用充電器之前請先閱讀所有指示以及充電器、電池組和
使用電池組的產品上的警告標記。
警告:觸電危險。切勿讓任何液體進入充電器否則可能會
導致觸電。
警告:建議使用漏電流額定值不超過30mA的漏電流保護
裝置。
小心:燒傷危險。為了減低受傷風險只可以使用
DeWALT
可充電電池。其他非原廠電池可能會爆裂導致人身傷害
和損害。
小心:必須監督兒童確保他們沒有耍玩器具。
注意:在某些情況下充電器連接到電源後充電器內暴露
的充電觸頭會被異物導致短路。導電的異物包括但不限於
鋼絲絨、鋁箔紙或任何由金屬粒子組成的物件必須要遠離
充電器範圍。充電器裡沒有電池組時一定要拔掉充電器的
電源。請先拔掉電源插頭後再清潔充電器。
請勿嘗試使用本手冊未提到的充電器為電池組充電。充電器
和電池組是專為搭配使用而特別設計。
除了為DeW ALT 可充電電池充電之外這些充電器不可以用於
其他用途。否則可能會導致火災、觸電或觸電致死。
請勿將充電器暴露在雨或雪中。
中斷充電器的電源時請拔除插頭而非拉扯電線。這樣會減低
電源插頭和電線損壞的風險。
請確保電線的位置不會遭踐踏、令人絆倒或容易受到其他方
式的損壞或受壓。
除非絕對需要否則請勿使用延長電線。使用不適當的延長電
線會引起火災、觸電或觸電致死。
請勿將任何物件放在充電器上面或是把充電器放在可能會
堵住通風槽的柔軟表面導致充電器的內部過熱。請將充電器
放到遠離熱源的位置。充電器透過外殼頂部及底部的槽散熱。
請勿操作電線或插頭損壞的充電器請立即予以更換。
如果充電器受到重擊、墜落或出現其他損壞情況請勿使用充
器,並應拿到授權維修中心修理。
請勿自行拆卸充電器。需要維護或修理時請拿到授權維修中
心。重新組裝不當可能會導致觸電、觸電致死或火災
若電源線損毀必須由製造商、服務代理或同等資質的人員立
即更換以避免發生危險。
在清潔之前請將充電器的插頭從電源插座上拔掉這樣可以
減低觸電風險。拆除電池組並不能夠降低這種風險。
切勿試圖將 2 個充電器連接在一起。
充電器是為標準 110 伏特的家用電源而設計。請勿試圖使用其
他電壓。本規定不適用於車載充電器。
為電池充電 B
1. 放入電池組前先將充電器的插頭插入適當的插座。
2. 將電池組
1
放進充電器確保電池組已完全放入。紅燈(充電
中)會不斷閃爍這表示充電程序已經開始。
3. 當紅燈持續亮起時代表充電完成。此時電池組的電力全滿
可以立即使用或是留在充電器裡。要從充電器上取下電池組
請按下電池組上的電池釋放按鈕
2
註:為了確保鋰離子電池組的效能及使用壽命最大化在第一次使
用電池組之前必須完全充電。
充電器操作
如需瞭解電池組的充電狀態請參閱以下指示燈。
充電狀態指示燈
充電中
已完全充電
電池組熱/冷延遲*
* 紅燈會繼續閃爍,但在執行此操作期間黃色指示燈將亮起電池組
達到適當溫度後黃色指示燈將熄滅充電器將恢復充電程序。
容的充電器不會為有故障的電池組充電。充電器會透過不亮燈來
表示電池組故障。
相容的充電器不會為有故障的電池組充電。充電器會通過不亮燈來
表示電池組故障。
註:亦有可能是充電器發生故障。
如果充電器指示故障請將充電器和電池組拿到授權維修中心進
行測試。
電池組熱/冷延遲
若充電器偵測到電池組過熱或過冷會自動啟動電池組熱/冷延遲
在電池組達到適合的溫度之前暫停充電。然後充電器會自動轉換
到電池組充電模式。此功能可確保電池組的使用壽命最大化。
冷電池組的充電速度大約是暖電池組的一半。在整個充電週期
池組會以較慢的充電速度進行充電即使電池組變暖充電速度亦
不會回復至最大充電速度。
DCB118 充電器具有專為冷卻電池組而設計的內部風扇。在需要冷
卻電池組時風扇會自動開啟。若風扇運作不正確或通風槽堵塞
勿操作充電器。請勿讓異物進入充電器內部。
繁體中文
1818
電子保護系統
XR 鋰離子工具的設計具有電子保護系統可保護電池組避免過載、
過熱或深度放電。
如果電子保護系統啟動本工具會自動關閉。如果出現此情況請將
鋰離子電池組放進充電器直到電力全滿。
牆面安裝
這些充電器經過精心設計可以安裝在牆面上或立在工作臺或工作
表面上。若採用牆面安裝請將充電器安裝在電源插座連接範圍內
的位置並遠離角落或可能阻礙空氣流動的障礙。將充電器的背面
用作在牆面上確定安裝螺絲位置的型板。使用長度至少 25.4 公釐、
螺頭直徑為7–9 公釐的牆用螺絲(另售)牢固安裝充電器旋進木料
的最佳深度為螺絲大約有5.5 公釐長度露在木料外。將露出的螺絲
與充電器背面的槽對齊並完全接合到槽中。
充電器清潔指示
警告:觸電危險。在清潔之前請將充電器的插頭從電源
插座上拔掉。使用軟布或非金屬軟刷去除充電器外部的污
垢和油脂。切勿讓任何液體滲入工具切勿讓工具的任何部
件浸在液體中。
電池組
所有電池組之重要安全指示
在訂購更換電池組時請務必附上目錄型號和電壓。
包裝箱內的電池組並未完全充電。使用電池組和充電器之前請閱
讀下列安全指示然後遵循所述的充電程式。
請閱讀所有指示
不要在易爆環境如有易燃液體、氣體或粉塵的環境中進行充
電或使用電池組。將電池組放進充電器或從充電器中取出電
池組可能會點燃粉塵或氣體。
切勿強行將電池組放進充電器。請勿以任何方式改裝電池組
以在不相容的充電器中使用否則電池組可能會破裂導致嚴
重人身傷害。
請僅使用指定的DeWALT充電器為電池充電。
請勿將水或其他液體飛濺到電池組或將電池組浸沒。
請勿在溫度可能達到或超過10F (40˚C)的地方(例如夏季時
屋外的棚屋或金屬建築物儲存或使用本工具和電池組。
即使電池組已嚴重損毀或磨損也請勿焚燒電池組。電池組
可能會在火中爆炸。焚燒鋰離子電池組時會產生有毒氣體和
物料。
若電池液體接觸到皮膚請立即以中性肥皂與清水沖洗接觸
範圍。若電池液體進入眼睛請睜開眼睛用清水沖洗 15 分鐘
或直到不適感消失為止。如果需要接受治療電池的電解質由
液化有機碳酸鹽和鋰鹽構成。
開啟的電池中的物質可能會導致刺激呼吸道。請轉移至空氣
流通處。如果症狀持續請尋求醫療救助。
警告:灼燒危險。電池液如遇到火花或火焰可能會引起
燃燒。
警告:不論是因為任何理由都不要嘗試打開電池。如果電
池組的外殼破裂或損毀請勿放進充電器。切勿撞擊、摔落
或損毀電池組。切勿使用受到重擊、墜落或出現其他損壞情
況的池組或充電器例如釘子刺穿、以鎚子敲打或踩踏)
否則可能會引起觸電或觸電致死。損毀的電池組應該送回
維修中心進行回收。
警告:火災危險。請勿在儲存或搬運電池組時讓金屬物件接
觸暴露的電池兩極。例如不要將電池組放在帶有鬆動的釘
子、螺絲、鑰匙等的地方。
小心:不使用工具時請將工具平放在沒有絆倒或跌落危險
的穩定平面上。一些具有大型電池組的工具可以直立但可
能會輕易被撞到。
運輸
警告:火災危險。搬運電池時若電池兩極意外接觸導電材料
可能會引發火災。運輸個別電池組時請確保電池兩級受到
保護並與可能接觸兩級並導致短路的材料隔絕。
註:鋰離子電池不應放在託運行李中。
DeWALT 電池符合行業和法律標準(包括聯合國危險貨物運輸建議
書、國際航空運輸協會 (IATA) 危險物品處理規則、國際海運危險物
(IMDG) 處理規則以及國際公路運送危險物品歐洲協議 (ADR)
規定的所有適用運輸規章。鋰離子電池和電池組均已根據《聯合國
危險貨物運輸建議書測試與標準手冊》 38.3 節的規定進行測試。
大多數情況下不會將運輸
DeWALT 電池組分歸為完全管制的第
9 類危險品。一般只有在運輸中包含額定能量大於100 瓦時 (Wh)
的鋰離子電池時才會將其分歸為完全管制的第 9 類危險品。
有鋰離子電池外殼上均標註有瓦時等級。此外由於規章的複雜
性,
DeWALT 不建議對鋰離子電池組單獨採用空運,不論其額定能
量是多少瓦時都是如此。若電池組的額定能量不超過 100 時,
可以同時空運工具與電池組(組合套件)
無論運輸是否納入完全管制範圍內運輸方均有責任諮詢瞭解針
對包裝、標籤/標記及單據要求的最新規定。手冊本節資訊基於良
好商譽原則提供在編製文件時被視為準確無誤但不提供任何明
示或暗示的保證。買方負有確保其行為遵守適用法規的責任。
運輸 FLEXVOLT
TM
電池
DeWALT FLEXVOLT
TM
電池有兩種模式:使用運輸
使用模式:FLEXVOLT® 電池單獨使用或在
DeWALT 18V (20V MAX) 產品
中使用時將作為18V (20V MAX) 電池運作。FLEXVOLT® 電池在54V (60V
MAX)108V (120V MAX)(兩 54V (60V MAX) 電池)產品中使用時將作
54V (60V MAX) 電池運作。
運輸模式:FLEXVOLT® 電池附加護蓋時電池將處於運輸模式。若將電
池組內的一連串電池中斷電氣連
會導致 3 個電池各自的瓦時
(Wh) 額定值低於 1 個電池的瓦時
額定值。這樣電池數量雖然增加到
3 但瓦時額定值更低因此能避開針對較高瓦時電池的運輸規
章。
例如若運輸瓦時額定值為
3 x 36 瓦時表示運輸 3
電池每個電池的額定值
36 瓦時。使用瓦時額定
值可能為 108 瓦時(表示 1
個電池)
儲存建議
1. 乾燥、涼爽、太陽不會直接照射、不會過熱或過冷的地方是電池
組的最佳存放地點。為達到最大效能和使用壽命不使用電池時
請以室溫儲存電池組。
2. 長期儲存建議將電力全滿的電池組從充電器卸下,儲存於
涼爽、乾燥處使電池組效能達到最佳。
註:電池組不應在電力耗盡的情況下儲存。在使用之前電池組必
須再次充電。
使用和運輸的標籤範例
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

DeWalt DCS356 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル
このマニュアルも適しています

他の言語で