Envelope 2
Controls
Attack: 300 µs to 5 s (linear attack)
Decay: 2.4 ms to 10 s (exponential decay)
Sustain: 0 V to 9 V
Release: 1.5 ms to 6 s (exponential release)
Output Section
Controls Volume: 0 to 100%
LED MIDI: Gate signal
Sample & Hold Section
Controls
Rate: 0.26 Hz to 28 Hz (can be clocked from extrenal source)
Glide: 500 µs to 1 s
LED Rate: 0.26 Hz to 28 Hz (can be clocked from extrenal source)
Slew Rate Limiter Section
Controls
Slew rate: 1 ms to 3 s
Portamento time: 0 to 10 s
Attenuator Section
Controls
Attenuator 1: +4 dB to -∞
Attenuator 2: 0 dB to -∞
Filter Section
Controls
Cuto frequency: 10 Hz to 15 kHz
Resonance: 0 to 10 (capable of self oscillation)
Modualtion depth: 0 to 100%
Envelope depth: 0 to 100%
Noise: 0 to 100%
VCA bias: 0 to 100%
Switches
Filter mode, high pass, band pass and low pass
Filter key track: on/o
LED Filter mode, high pass, band pass and low pass
LFO Section
Controls
Shape: Sine, Triangle, Sawtooth, Square and Ramp
Rate: 0 to 10 (0.01Hz to 10kHz)
Switches Key sync: on/o
LED
Rate/Level indicator
Shape: Sine, Triangle, Sawtooth, Square and Ramp.
Delay Section
Controls
Time: 25 ms to 640 ms
Repeats: 0 to 100%
Mix: 0 to 100%
Overdrive Section
Controls
Drive: 0 to 11
Tone: 0 to 10
Level: 0 dB to -∞
LED Drive amount indicator
Inputs (TS 3.5 mm)
OSC 1 Control voltage: 1 V per octave
OSC 2 Control voltage: 1 V per octave
OSC 1&2 Control voltage: 1 V per octave
INVERT IN inverts voltage
SHAPE 1 Control voltage: -5 V to +5 V
SHAPE 2 Control voltage: -5 V to +5 V
PULSE WIDTH 1 Control voltage: -5 V to +5 V
PULSE WIDTH 2 Control voltage: -5 V to +5 V
VCF IN Signal input
FREQ MOD Control voltage: -5 V to +5 V
RESONANCE Control voltage: -5 V to +5 V
OVERDRIVE IN Signal input
VCA IN Signal input
VCA CV Control voltage: -9 V to +9 V
DELAY IN Signal input
DELAY TIME Control voltage: -5 V to +5 V
E GATE 1 Control voltage: -5 V to +5 V (envelope triggers @ 1.5 V)
E GATE 2 Control voltage: -5 V to +5 V (envelope triggers @ 1.5 V)
SAMPLE & HOLD IN Signal input
SAMPLE & HOLD CLOCK Control voltage: -5 V to +5 V (S&H triggers @ 3 V)
LFO RATE Control voltage: -5 V to +5 V
LFO SHAPE Control voltage: -5 V to +5 V
LFO TRIG Control voltage: -5 V to +5 V (S&H triggers @ 1.6 V)
MULT (Multiple) Input Signal is duplicated on Mult 1 and Mult 2 outputs
ATT 1 IN Signal input
ATT 1 CV Control voltage: -5 V to +5 V
ATT 2 IN Signal input
SLEW IN Signal or CV input
SUM1(A) Signal input or CV input
SUM1(B) Signal input or CV input
SUM2(A) Signal input or CV input
SUM2(B) Signal input or CV input
18 19NEUTRON