Hilti C 4-36-90 ユーザーマニュアル

C 4/36-90

C 4/36-350

C 4/36-DC

English 1

Dansk 11

Svenska 21

Norsk 30

Suomi 40

Русский 49

Български 61

Română 73

Türkçe 84

ﻋﺮﺑﻲ 94

Latviešu 105

Lietuvių 115

Eesti 125

Қазақ 135

日本語 147

한국어 157

中文 166

繁體中文 174

1

2

3

4

C 4/36-90

C 4/36-350

C 4/36-DC

en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 1

da Originalbrugsanvisning .............................. 11

sv Originalbruksanvisning ............................... 21

no Originalbruksanvisning............................... 30

fi Alkuperäisetohjeet .................................. 40

ru Перевод оригинального руководства по

эксплуатации ...................................... 49

bg Оригинално Ръководство за експлоатация . . . . . . . . . . . . . 61

ro Manual de utilizare original . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

tr Orijinal kullanım kılavuzu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ .............................. 94

lv Oriģinālā lietošanas instrukcija . . . . . . . . . . . . . . . . . . . . . . . . 105

lt Originali naudojimo instrukcija . . . . . . . . . . . . . . . . . . . . . . . . 115

et Originaalkasutusjuhend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

kk Түпнұсқа пайдалану бойынша нұсқаулық . . . . . . . . . . . . . 135

ja オリジナル取扱説明書................................ 147

ko 오리지널사용설명서 ................................ 157

cn 原版操作说明....................................... 166

zh 原始操作說明....................................... 174

*2024463* 2024463 English 1

Original operating instructions

1 Information about the operating instructions

1.1 About these operating instructions

• Read these operating instructions before the product is used or operated

for the first time. This is a prerequisite for safe, trouble-free handling and

use of the product.

• Observe the safety instructions and warnings in these operating instruc-

tions and on the product.

• Always keep the operating instructions with the product and make sure

that the product is accompanied by these operating instructions only,

when the product is given to other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the

product. The following signal words are used:

DANGER

DANGER !

▶Draws attention to imminent danger that will lead to serious personal

injury or fatality.

WARNING

WARNING !

▶Draws attention to a potential threat of danger that can lead to serious

injury or fatality.

CAUTION

CAUTION !

▶Draws attention to a potentially dangerous situation that could lead to

personal injury or damage to the equipment or other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use.

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household

waste

2 English 2024463 *2024463*

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

These numbers refer to the corresponding illustrations found at the

beginning of these operating instructions

The numbering reflects the sequence of operations shown in the

illustrations and may deviate from the steps described in the text

Item reference numbers are used in the overview illustrations and

refer to the numbers used in the product overview section

This symbol is intended to draw special attention to certain points

when handling the product.

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols are used:

For indoor use only

Double insulated

1.4 Product information

Hilti products are designed for professional use and may be operated,

serviced and maintained only by trained, authorized personnel. This

personnel must be specifically informed about the possible hazards. The

product and its ancillary equipment can present hazards if used incorrectly

by untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are printed on the rating plate.

▶Write down the serial number in the table below. You will be required to

state the product details when contacting Hilti Service or your local Hilti

organization to inquire about the product.

Product information

Charger C4/36-90

C4/36-350

C4/36-DC

Generation 01

Serial no.

1.5 Declaration of conformity

We declare, on our sole responsibility, that the product described here

complies with the applicable directives and standards. A copy of the

declaration of conformity can be found at the end of this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916

Kaufering, Germany

*2024463* 2024463 English 3

2 Safety

2.1 General power tool safety warnings

WARNING

Read all safety warnings and all instructions. Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

Work area safety

▶Keep work area clean and well lit. Cluttered or dark areas invite

accidents.

▶Do not operate power tools in explosive atmospheres, such as in

the presence of flammable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

▶Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

Electrical safety

▶Power tool plugs must match the outlet. Never modify the plug in

any way. Do not use any adapter plugs with earthed (grounded)

power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

▶Avoid body contact with earthed or grounded surfaces, such as

pipes, radiators, ranges and refrigerators. There is an increased risk

of electric shock if your body is earthed or grounded.

▶Do not expose power tools to rain or wet conditions. Water entering

a power tool will increase the risk of electric shock.

▶Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled cords increase the risk

of electric shock.

▶When operating a power tool outdoors, use an extension cord

suitable for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

▶If operating a power tool in a damp location is unavoidable, use

a residual current device (RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

Personal safety

▶Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired

or under the influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in serious personal

injury.

▶Use personal protective equipment. Always wear eye protection.

Protective equipment such as dust mask, non-skid safety shoes, hard

4 English 2024463 *2024463*

hat, or hearing protection used for appropriate conditions will reduce

personal injuries.

▶Prevent unintentional starting. Ensure the switch is in the off‐position

before connecting to power source, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energising power

tools that have the switch on invites accidents.

▶Remove any adjusting key or wrench before turning the power tool

on. A wrench or a key left attached to a rotating part of the power tool

may result in personal injury.

▶Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

▶Dress properly. Do not wear loose clothing or jewellery. Keep your

hair, clothing and gloves away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving parts.

▶If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used.

Use of dust collection can reduce dust-related hazards.

Power tool use and care

▶Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at

the rate for which it was designed.

▶Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled with the switch is dangerous

and must be repaired.

▶Disconnect the plug from the power source from the power tool

before making any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce the risk of starting

the power tool accidentally.

▶Store idle power tools out of the reach of children and do not

allow persons unfamiliar with the power tool or these instructions

to operate the power tool. Power tools are dangerous in the hands of

untrained users.

▶Maintain power tools. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly maintained power

tools.

▶Keep cutting tools sharp and clean. Properly maintained cutting tools

with sharp cutting edges are less likely to bind and are easier to control.

▶Use the power tool, accessories and tool bits etc. in accordance

with these instructions, taking into account the working conditions

and the work to be performed. Use of the power tool for operations

different from those intended could result in a hazardous situation.

*2024463* 2024463 English 5

2.2 Battery charger use and care

▶To avoid injury, use the charger only to charge Hilti Li-ion batteries

approved for use with this charger.

▶The location at which the charger is used should be clean, cool, dry and

protected from frost.

▶The charger must be able to emit heat while in operation. The air vents

must therefore remain unobstructed. Do not operate the charger inside

a closed container.

▶Maintain the product carefully. Make sure that no parts are broken or

damaged in such a way that the product no longer functions correctly. If

parts are damaged or broken, have the product repaired prior to further

use.

▶Use chargers and the corresponding batteries in accordance with these

instructions and as is specified for this particular model. Use of chargers

for applications different from those intended could result in hazardous

situations.

▶Recharge the batteries only with the chargers specified by the manufac-

turer. A charger that is suitable for a certain type of battery may present

a risk of fire when used with other types of battery.

▶When not in use, keep the battery and the charger away from paper

clips, coins, keys, nails, screws or other small metal objects that could

cause a short circuit at the battery terminals or the charging contacts.

A short circuit between the battery terminals or charging contacts may

cause injuries (burns) and result in fire.

▶Do not store the battery on the charger. Always remove the battery from

the charger when the charging operation has completed.

2.3 Careful handling and use of batteries

▶Observe the special guidelines applicable to the transport, storage and

use of lithium-ion batteries.

▶Do not expose batteries to high temperatures, direct sunlight or fire.

▶Do not disassemble, crush or incinerate batteries and do not subject

them to temperatures over 80 °C (176 °F).

▶Do not use or charge batteries that have suffered mechanical impact,

have been dropped from a height or show signs of damage. In this case,

always contact your Hilti Service.

▶If the battery is too hot to touch it may be defective. Put the battery in

a place where it is clearly visible and where there is no risk of fire, at an

adequate distance from flammable materials. Allow the battery to cool

down. If it is still too hot to touch after an hour, the battery is faulty.

Contact Hilti Service.

6 English 2024463 *2024463*

3 Description

3.1 Product overview 1

@Release button with additional

function (state of charge dis-

play activation)

;Battery

=Battery state of charge LED

indicators

%Indicator LED

&Battery interface

3.2 Intended use

The product described is a battery charger for Hilti Li-Ion batteries with a

rated voltage of 7.2 to 36 volts. It is designed to be connected to power

outlets providing an AC (alternating current) voltage of 100 to 127 volts or

220 to 240 volts (depending on country-specific version).

The C4-36-DC charger can be connected to a 12 volt or 24 volt DC electric

supply socket in a motor vehicle.

The batteries approved for use with this product are listed at the end of this

document.

Not all batteries are available in all markets.

3.3 Information displayed

3.3.1 Information displayed by the charger and battery 2

Display On the battery On the charger

LED lights constantly. Indication of state of

charge. The charger is con-

nected and ready for

operation.

Blinking. Charging is in

progress. The battery is too hot

or too cold.

LED doesn’t light. Green LED on the

charger lights con-

stantly , no LEDs light

on the battery: Battery

malfunction.

Charger malfunction.

3.3.2 Li-ion battery state of charge display 2

Status Meaning

4 LEDs light. State of charge: 100 %

3 LEDs light, 1 LED blinks. State of charge: 75 % to 100 %

2 LEDs light, 1 LED blinks. State of charge: 50 % to 75 %

1 LED lights, 1 LED blinks. State of charge: 25 % to 50 %

1 LED blinks. State of charge: < 25 %

*2024463* 2024463 English 7

3.4 Items supplied

Charger, operating instructions.

Other system products approved for use with this product can be found at

your local Hilti Store or at: www.hilti.group | USA: www.hilti.com

4 Technical data

C 4/3690 C 4/36350 C 4/36DC

Weight 0.6 kg 1.1 kg 0.6 kg

Output voltage 7.2 V … 36 V 7.2 V … 36 V 7.2 V … 36 V

Output power 110 V 90 W 350 W •/•

230 V 90 W 365 W •/•

12 V •/• •/• 60 W

24 V •/• •/• 60 W

5 Operation

5.1 Switching on the C 4/36-90 and C 4/36-350 charger

C 4/36-90

C 4/36-350

▶Plug the supply cord into the power outlet.

▶The green LED on the charger lights.

5.2 Switching the C 4/36-DC charger on

C 4/36-DC

When charging a Hilti battery with the C 4/36-DC charger, the motor

vehicle’s starter battery may discharge to such an extent that the battery

is no longer capable of fulfilling its purpose

Depending on how the motor vehicle’s electrical system is configured,

the charger will either receive power immediately or only after the ignition

is switched on.

▶Plug the supply cord into the motor vehicle’s cigarette lighter socket.

▶The green LED on the charger lights constantly when the input voltage

is correct.

8 English 2024463 *2024463*

5.3 Inserting and charging the battery 3

The battery will suffer no damage even when left in the charger for

long periods. In this case it is necessary that the charger is operating

(green LED on the charger must be lit). The battery state of charge LED

goes out after some time, even though the battery is fully charged, and

cannot be subsequently reactivated to indicate the state of charge. For

safety reasons, it is recommended that the battery is removed from the

charger after completion of the charging cycle.

Liion batteries are ready for use at any time, even when only partly

charged. Charging progress is indicated by the LEDs.

1. Before inserting the battery, check that the contacts are clean and free

from grease.

2. Push the battery into the interface provided.

3. Check that the battery and charger interfaces match (keyed fit).

▶Charging begins automatically after insertion of the battery in the

charger.

5.4 Removing the battery 4

1. Press the catch to release the battery.

2. Pull the battery out of the charger.

6 Troubleshooting

Malfunction Possible cause Action to be taken

LEDs on the battery

don’t light, battery is

in the charger.

The battery may be de-

fective.

▶Remove the battery

from the charger. If

no LED lights on the

battery after activation

of the state of charge

indicator, the battery

is defective. Have the

battery checked by

Hilti Service.

LEDs on the charger

blink. The battery is too hot

or too cold: the battery

doesn’t charge.

▶The charger switches

automatically to

charging mode as

soon as the battery

reaches the required

temperature.

*2024463* 2024463 English 9

Malfunction Possible cause Action to be taken

LEDs on the charger

don’t light. Charger malfunction. ▶Unplug the appliance

and then plug it back

in. If the LED still

doesn’t light, please

bring the charger to

Hilti Service.

7 Care and maintenance

WARNING

Electric shock hazard! Attempting care and maintenance with the supply

cord connected to a power outlet can lead to severe injury and burns.

▶Always unplug the supply cord before carrying out care and maintenance

tasks.

Care

• Carefully remove stubborn dirt from the tool.

• Clean the air vents carefully with a dry brush.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning

agents containing silicone as they can attack the plastic parts.

Maintenance

WARNING

Danger of electric shock! Improper repairs to electrical components may

lead to serious injuries including burns.

▶Repairs to the electrical section of the tool or appliance may be carried

out only by trained electrical specialists.

• Check all visible parts and controls for signs of damage at regular

intervals and make sure that they all function correctly.

• Do not operate the product if signs of damage are found or if parts

malfunction. Have it repaired immediately by Hilti Service.

• After cleaning and maintenance, fit all guards or protective devices and

check that they function correctly.

To help ensure safe and reliable operation, use only genuine Hilti spare

parts and consumables. Spare parts, consumables and accessories

approved by Hilti for use with the product can be found at your local

Hilti Store or online at: www.hilti.group.

10 English 2024463 *2024463*

8 Disposal

WARNING

Risk of injury due to incorrect disposal! Health hazards due to escaping

gases or liquids.

▶DO NOT send batteries through the mail!

▶Cover the terminals with a non-conductive material (such as electrical

tape) to prevent short circuiting.

▶Dispose of your battery out of the reach of children.

▶Dispose of the battery at your Hilti Store, or consult your local gov-

ernmental garbage disposal or public health and safety resources for

disposal instructions.

Most of the materials from which Hilti tools and appliances are manu-

factured can be recycled. The materials must be correctly separated before

they can be recycled. In many countries, your old tools, machines or appli-

ances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti

representative for further information.

In accordance with the European Directive on waste electrical and electronic

appliances and its implementation in conformance with national law, elec-

trical and electronic appliances that have reached the end of their life must

be collected separately and returned to an environmentally compatible re-

cycling facility.

▶Do not dispose of electrical and electronic appliances together with

household waste!

9 RoHS (Restriction of Hazardous Substances)

Click on the links to go to the table of hazardous substances:

• For C 4/36-90, 230 V, China: qr.hilti.com/2034530

• For C 4/36-90, 110 V, Taiwan: qr.hilti.com/2026281

• For C 4/36-350, 230 V, China: qr.hilti.com/2028875

• For C 4/36-350, 110 V, Taiwan: qr.hilti.com/2028992

There is a link to the RoHS table, in the form of a QR code, at the end of this

document.

10 Manufacturer’s warranty

▶Please contact your local Hilti representative if you have questions about

the warranty conditions.

*2024463* 2024463 Dansk 11

Original brugsanvisning

1 Om brugsanvisningen

1.1 Om denne brugsanvisning

• Læs brugsanvisningen grundigt igennem inden ibrugtagning. Det er en

forudsætning for sikkert arbejde og korrekt håndtering.

• Følg sikkerhedsanvisningerne og advarslerne i denne brugsanvisning og

på produktet.

• Opbevar altid brugsanvisningen sammen med produktet, og overdrag

kun produktet til andre personer sammen med denne brugsanvisning.

1.2 Tegnforklaring

1.2.1 Advarsler

Advarsler advarer mod farer ved håndtering af produktet. Følgende signalord

anvendes:

FARE

FARE !

▶Betegner en umiddelbart truende fare, der kan medføre alvorlige kvæ-

stelser eller døden.

ADVARSEL

ADVARSEL !

▶Står ved en potentielt truende fare, der kan medføre alvorlige kvæstelser

eller døden.

FORSIGTIG

FORSIGTIG !

▶Advarer om en potentielt farlig situation, der kan forårsage personskader

eller materielle skader.

1.2.2 Symboler i denne dokumentation

Følgende symboler anvendes i denne dokumentation:

Læs brugsanvisningen før brug

Anvisninger for anvendelse og andre nyttige oplysninger

Håndtering af genvindbare materialer

Elektriske maskiner og batterier må ikke bortskaffes som almindeligt

husholdningsaffald

1.2.3 Symboler i illustrationer

Følgende symboler anvendes på illustrationer:

12 Dansk 2024463 *2024463*

Disse tal henviser til de forskellige illustrationer i begyndelsen af

brugsanvisningen

Nummereringen udtrykker arbejdstrinnenes rækkefølge på illustratio-

nen og kan afvige fra arbejdstrinnene i teksten

Positionsnumre anvendes i illustrationen Oversigt og refererer til

tallene i symbolforklaringen i afsnittet Produktoversigt

Dette symbol skal sikre skærpet opmærksomhed ved omgang med

produktet.

1.3 Produktspecifikke symboler

1.3.1 Symboler på produktet

Følgende symboler anvendes på produktet:

Kun til anvendelse indendørs

Dobbeltisoleret

1.4 Produktoplysninger

Hilti-produkter er beregnet til professionel brug og må kun betjenes, efterses

og vedligeholdes af autoriseret og instrueret personale. Dette personale skal

i særdeleshed informeres om de potentielle farer, der er forbundet med

brugen af dette produkt. Der kan opstå farlige situationer ved anvendelse af

produktet og det tilhørende udstyr, hvis det anvendes af personer, der ikke

er blevet undervist i dens brug, eller hvis det ikke anvendes korrekt i henhold

til forskrifterne i denne brugsanvisning.

Typebetegnelse og serienummer fremgår af typeskiltet.

▶Notér serienummeret i den efterfølgende tabel. Du skal bruge pro-

duktoplysningerne ved henvendelser til vores lokale afdeling eller vores

serviceværksted.

Produktoplysninger

Lader C4/36-90

C4/36-350

C4/36-DC

Generation 01

Serienummer

1.5 Overensstemmelseserklæring

Vi erklærer som eneansvarlige, at det beskrevne produkt er i overensstem-

melse med gældende direktiver og standarder. Sidst i dette dokument finder

du et bilede af overensstemmelseserklæringen.

Den tekniske dokumentation er arkiveret her:

Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916

Kaufering, DE

*2024463* 2024463 Dansk 13

2 Sikkerhed

2.1 Generelle sikkerhedsanvisninger for elværktøj

ADVARSEL Læs alle sikkerhedsanvisninger og instruktioner. Hvis

sikkerhedsanvisningerne og instruktionerne ikke overholdes, er der risiko for

elektrisk stød, brand og/eller alvorlige personskader.

Opbevar alle sikkerhedsanvisninger og instruktioner til senere brug.

Arbejdspladssikkerhed

▶Sørg for at holde arbejdsområdet ryddeligt og godt oplyst. Uorden

eller uoplyste arbejdsområder øger faren for uheld.

▶Brug ikke elværktøj i eksplosionstruede omgivelser, hvor der er

brændbare væsker, gasser eller støv. Elværktøj kan slå gnister, der

kan antænde støv eller dampe.

▶Hold børn og andre personer på sikker afstand under brug af

elværktøjet.Hvis du bliver distraheret, kan du miste kontrollen over

maskinen.

Elektrisk sikkerhed

▶Elværktøjets stik skal passe til kontakten. Stikket må under ingen

omstændigheder ændres. Brug ikke adapterstik sammen med

jordforbundne elværktøj. Uændrede stik, der passer til kontakterne,

nedsætter risikoen for elektrisk stød.

▶Undgå kropskontakt med jordforbundne overflader som f.eks. rør,

radiatorer, komfurer og køleskabe. Hvis din krop er jordforbundet,

øges risikoen for elektrisk stød.

▶Elværktøj må ikke udsættes for regn eller fugt. Indtrængning af vand

i elværktøj øger risikoen for elektrisk stød.

▶Brug ikke ledningen til formål, den ikke er beregnet til (f.eks. må

man aldrig bære elværktøjet i ledningen, hænge det op i ledningen

eller rykke i ledningen for at trække stikket ud af kontakten). Beskyt

ledningen mod varme, olie, skarpe kanter eller maskindele, der er i

bevægelse. Beskadigede eller sammenviklede ledninger øger risikoen

for elektrisk stød.

▶Hvis elværktøjet benyttes i det fri, må der kun benyttes en forlæn-

gerledning, der er egnet til udendørs brug. Brug af forlængerledning

til udendørs brug nedsætter risikoen for elektrisk stød.

▶Hvis det ikke kan undgås at anvende elværktøjet i fugtige omgivelser,

skal du anvende et fejlstrømsrelæ. Anvendelsen af et fejlstrømsrelæ

nedsætter risikoen for et elektrisk stød.

Personlig sikkerhed

▶Det er vigtigt at være opmærksom, se, hvad man laver, og bruge

maskinen fornuftigt. Anvend aldrig elværktøj, hvis du er træt eller

påvirket af stoffer, alkohol eller medicin. Et øjebliks uopmærksomhed

under brugen af elværktøjet kan medføre alvorlige personskader.

14 Dansk 2024463 *2024463*

▶Brug beskyttelsesudstyr, og hav altid beskyttelsesbriller på. Brug af

sikkerhedsudstyr som f.eks. støvmaske, skridsikkert fodtøj, beskyttel-

seshjelm eller høreværn afhængigt af elværktøjets type og anvendelse

nedsætter risikoen for personskader.

▶Undgå utilsigtet igangsætning. Kontrollér, at elværktøjet er

frakoblet, før du slutter det til strømforsyningen, tager det op

eller transporterer det. Undgå at bære elværktøjet med fingeren på

afbryderen, og sørg for, at det ikke er tændt, når det sluttes til nettet, da

dette øger risikoen for personskader.

▶Fjern indstillingsværktøj eller skruenøgler, inden elværktøjet tæn-

des. Hvis et stykke værktøj eller en nøgle sidder i en roterende maskindel,

er der risiko for personskader.

▶Undgå at arbejde i unormale kropsstillinger. Sørg for at stå sikkert,

mens der arbejdes, og kom ikke ud af balance. Det er derved nemmere

at kontrollere elværktøjet, hvis der skulle opstå uventede situationer.

▶Brug egnet arbejdstøj. Undgå løse beklædningsgenstande eller

smykker. Hold hår, tøj og handsker væk fra dele, der bevæger sig.

Dele, der er i bevægelse, kan gribe fat i løstsiddende tøj, smykker eller

langt hår.

▶Hvis støvudsugnings- og opsamlingsudstyr kan monteres, er det

vigtigt, at dette tilsluttes og benyttes korrekt. Ved at anvende en

støvudsugning er det muligt at nedsætte risiciene som følge af støv.

Anvendelse og pleje af elværktøjet

▶Undgå at overbelaste maskinen. Brug altid en maskine, der er

beregnet til det stykke arbejde, der skal udføres. Med det rigtige

værktøj arbejder man bedst og mest sikkert inden for det angivne

effektområde.

▶Brug ikke elværktøj, hvis afbryderen er defekt. En maskine, der ikke

kan startes og stoppes, er farlig og skal repareres.

▶Træk stikket ud af stikkontakten, inden maskinen indstilles, inden

der skiftes tilbehørsdele, eller inden du lægger maskinen fra dig.

Disse sikkerhedsforanstaltninger forhindrer utilsigtet start af elværktøjet.

▶Opbevar ubenyttede elværktøjer uden for børns rækkevidde. Lad

aldrig personer, der ikke er fortrolige med elværktøjet eller ikke

har gennemlæst sikkerhedsanvisningerne benytte dette. Elværktøj

er farligt, hvis det benyttes af ukyndige personer.

▶Sørg for at pleje elværktøj omhyggeligt. Kontrollér, om bevægelige

dele fungerer korrekt og ikke sidder fast, og om delene er brækket

eller beskadiget, således at elværktøjets funktion påvirkes. Få

beskadigede dele repareret, inden elværktøjet tages i brug. Mange

uheld skyldes dårligt vedligeholdte elværktøjer.

▶Sørg for, at skæreværktøjer er skarpe og rene. Omhyggeligt ved-

ligeholdte skæreværktøjer med skarpe skærekanter sætter sig ikke så

hurtigt fast og er nemmere at føre.

*2024463* 2024463 Dansk 15

▶Anvend elværktøj, tilbehør, indsatsværktøj osv. i overensstemmelse

med disse anvisninger. Tag hensyn til arbejdsforholdene og det

arbejde, der skal udføres. I tilfælde af anvendelse af maskinen til

formål, som ligger uden for det fastsatte anvendelsesområde, kan der

opstå farlige situationer.

Service

▶Sørg for, at elværktøjet kun repareres af kvalificerede fagfolk, og at

der altid benyttes originale reservedele. Dermed sikres størst mulig

elværktøjssikkerhed.

2.2 Omhyggelig omgang med og brug af ladere

▶Man må kun oplade godkendte Hilti li-ion-batterier for at undgå tilska-

dekomst.

▶Laderen skal placeres et rent, køligt, tørt og frostfrit sted.

▶Under opladningen skal laderen kunne afgive varme. Ventilationsåb-

ningerne må derfor ikke være blokeret. Laderen må ikke anvendes til

opladning i en lukket beholder.

▶Sørg for at pleje produktet omhyggeligt. Kontrollér, at ingen dele er gået

i stykker eller er så beskadigede, at produktet ikke længere fungerer

korrekt. Hvis dele er gået i stykker eller er beskadigede, skal du få

produktet repareret, før du bruger det yderligere.

▶Anvend ladere og tilhørende batterier i henhold til anvisningerne og i

overensstemmelse med forskrifterne for dette bestemte apparat. Hvis

ladere anvendes til andre formål end dem, de er beregnet til, kan det

medføre farlige situationer.

▶Oplad kun batterier i ladere, der er anbefalet af producenten. Der er risiko

for brand, hvis en lader, der er beregnet til et bestemt batteri, anvendes

til opladning af en anden batteritype.

▶Når batteri og lader ikke er i brug, skal de holdes langt væk fra

papirclips, mønter, nøgler, søm, skruer og andre små metalgenstande,

som kan kortslutte batteriets eller laderens kontakter. En kortslutning

mellem batteripolerne eller ladekontakterne kan medføre forbrændinger

og brand.

▶Opbevar ikke batteriet i laderen. Tag batteriet ud af laderen, når

opladningen er gennemført.

2.3 Omhyggelig omgang med og brug af batterier

▶Læs de særlige retningslinjer for transport, opbevaring og brug af

lithiumion-batterier.

▶Hold batterier på sikker afstand af høje temperaturer, direkte solindstrå-

ling og ild.

▶Batterierne må ikke adskilles, klemmes, opvarmes til over 80 °C eller

brændes.

16 Dansk 2024463 *2024463*

▶Anvend og oplad ikke batterier, som har fået et slag, er faldet på gulvet

fra mere end en meters højde eller på anden vis er blevet beskadiget.

Kontakt i så fald altid Hilti Service.

▶Hvis batteriet er for varmt til at kunne røres, kan det være defekt. Anbring

batteriet på et overskueligt, ikke-brændbart sted med tilstrækkelig af-

stand til brændbare materialer. Lad batteriet køle af. Hvis batteriet efter

en time fortsat er for varmt til at kunne røres, er det er defekt. Kontakt

Hilti Service.

3 Beskrivelse

3.1 Produktoversigt 1

@Frigørelsesknap med ekstra-

funktion til aktivering af ladetil-

standsvisning

;Batteri

=Ladetilstandsindikator

%Indikatorlampe

&Batteritilslutning

3.2 Tilsigtet anvendelse

Det beskrevne produkt er en lader til Hilti Li-Ion-batterier med en nominel

spænding på 7,2 til 36 volt. Det er, alt efter national model, beregnet til tilslut-

ning til stikdåser med 100 til 127 volt eller 220 til 240 volt vekselspænding.

Laderen C4-36-DC kan sluttes til et stik i bilen med 12-V- eller 24-V-

jævnstrøm.

De batterier, som er godkendt til dette produkt, finder du sidst i denne

dokumentation.

Ikke alle batterier fås på alle markeder.

3.3 Visningselementer

3.3.1 Visningselementer på lader og batteri 2

Visning Betydning ved batteri Betydning ved lader

Lampen lyser Visning af ladetilstand Lader tilsluttet og klar

til brug.

Blinker Opladning aktiv Batteriet er for varmt

eller for koldt.

Slukket Den grønne indikator-

lampe på laderen lyser,

alle indikatorlamper på

batteriet er slukket: Fejl

på batteriet.

Fejl på laderen.

3.3.2 Ladetilstandsvisning på lithium-ion-batteri 2

Tilstand Betydning

4 lysdioder. Ladetilstand: 100 %

ページが読み込まれています...

Hilti C 4-36-90 ユーザーマニュアル

Hilti C 4-36-90 ユーザーマニュアル

他の言語で

関連論文