2. Hilti
  3. TE 500-A36
TE 500-A36

Hilti TE 500-A36 取扱説明書

  • こんにちは！Hilti TE 500-A36ハンマードリルの取扱説明書を読み終えました。この機器に関するご質問がありましたら、お気軽にお尋ねください。安全な使用方法、メンテナンス方法、仕様など、このマニュアルに記載されている情報に基づいてご回答いたします。
  • TE 500-A36の電源の入れ方と切り方は？
    TE 500-A36を使用する際の安全上の注意事項は？
    TE 500-A36のシリアル番号はどこに記載されていますか？
TE 500-A36
English 1
Dansk 12
Svenska 23
Norsk 34
Suomi 45
Eesti 56
Latviešu 67
Lietuvių 79
Türkçe 91
ﻋﺮﺑﻲ 102
日本語 114
한국어 125
繁體中文 136
中文 146
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
1
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
2
3
4
5
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
TE 500-A36
en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
da Original brugsanvisning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
sv Originalbruksanvisning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
no Original bruksanvisning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
fi Alkuperäiset ohjeet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
et Originaalkasutusjuhend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
lv Oriģinālā lietošanas instrukcija . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
lt Originali naudojimo instrukcija . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
tr Orijinal kullanım kılavuzu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
ja オリジナル取扱説明書 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
ko 오리지널 사용 설명서 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
zh 原始操作說明 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
cn 原版操作说明 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
*2240497*
2240497 English 1
1 Information about the documentation
1.1 About this documentation
• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free
handling and use of the product.
• Observe the safety instructions and warnings in this documentation and on the product.
• Always keep the operating instructions with the product and make sure that the operating instructions
are with the product when it is given to other persons.
1.2 Explanation of symbols used
1.2.1 Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words
are used:
DANGER
DANGER !
▶ Draws attention to imminent danger that will lead to serious personal injury or fatality.
WARNING
WARNING !
▶ Draws attention to a potential threat of danger that can lead to serious injury or fatality.
CAUTION
CAUTION !
▶
Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage
to the equipment or other property.
1.2.2 Symbols in the documentation
The following symbols are used in this document:
Read the operating instructions before use.
Instructions for use and other useful information
Dealing with recyclable materials
Do not dispose of electric equipment and batteries as household waste
1.2.3 Symbols in the illustrations
The following symbols are used in illustrations:
These numbers refer to the corresponding illustrations found at the beginning of these operating
instructions
The numbering reflects the sequence of operations shown in the illustrations and may deviate
from the steps described in the text
Item reference numbers are used in the overview illustrations and refer to the numbers used in
the product overview section
This symbol is intended to draw special attention to certain points when handling the product.
1.3 Product-dependent symbols
1.3.1 Symbols on the product
The following symbols can be used on the product:
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
2 English 2240497
*2240497*
Chiseling
Chisel positioning
Service indicator
Diameter
Rated speed under no load
Revolutions per minute
Direct current (DC)
Wireless data transfer
Li-ion battery
Hilti Li-ion battery type series used. Observe the information given in the section headed In-
tended use.
1.4 Switching on and off
Symbols
Product is switched on
Product is switched off
1.5 Product information
products are designed for professional users and only trained, authorized personnel are
permitted to operate, service and maintain the products. This personnel must be specifically informed about
the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by
untrained personnel or if used not in accordance with the intended use.
The type designation and serial number are printed on the rating plate.
▶ Write down the serial number in the table below. You will be required to state the product details when
contacting Hilti Service or your local Hilti organization to inquire about the product.
Product information
Breakers TE 500A36
Generation 04
Serial no.
1.6 Declaration of conformity
We declare, onour sole responsibility, that the product described here complies with the applicable directives
and standards. A copy of the declaration of conformity can be found at the end of this documentation.
The technical documentation is filed here:
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany
2 Safety
2.1 General power tool safety warnings
WARNING Read all safety warnings, instructions, illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
*2240497*
2240497 English 3
Work area safety
▶ Keep work area clean and well lit. Cluttered or dark areas invite accidents.
▶ Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
▶ Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
Electrical safety
▶ Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
▶ Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
▶ Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
▶ Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the
risk of electric shock.
▶ When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
▶ If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
Personal safety
▶ Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury.
▶ Use personal protective equipment. Always wear eye protection. Protective equipment such as a
dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will
reduce personal injuries.
▶ Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power
source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on
the switch or energising power tools that have the switch on invites accidents.
▶ Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
▶ Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
▶ Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
▶ If devices are provided for the connection of dust extraction and collection facilities, ensure these
are connected and properly used. Use of dust collection can reduce dust-related hazards.
▶ Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore
tool safety principles. A careless action can cause severe injury within a fraction of a second.
Power tool use and care
▶ Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
▶ Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
▶ Disconnect the plug from the power source and/or remove the battery pack, if detachable, from
the power tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
▶ Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
▶ Maintain power tools and accessories. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained power
tools.
▶ Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
4 English 2240497
*2240497*
▶ Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
▶ Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
Battery tool use and care
▶ Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with another battery pack.
▶ Use power tools only with specifically designated battery packs. Use of any other battery packs may
create a risk of injury and fire.
▶ When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects, that can make a connection from one terminal to
another. Shorting the battery terminals together may cause burns or a fire.
▶ Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
▶ Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may
exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
▶ Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature
above 130° C (265 °F) may cause explosion.
▶ Follow all charging instructions and do not charge the battery pack or tool outside the temperature
range specified in the instructions. Charging improperly or at temperatures outside the specified range
may damage the battery and increase the risk of fire.
Service
▶ Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
▶ Never service damaged battery packs. Service of battery packs should only be performed by the
manufacturer or authorized service providers.
2.2 Hammer safety warnings
Safety instructions for all operations
▶ Wear ear protectors. Exposure to noise can cause hearing loss.
▶ Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
▶ Hold the power tool by insulated gripping surfaces, when performing an operation where the
cutting accessory may contact hidden wiring. Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give the operator an electric shock.
2.3 Additional safety instructions for breakers
Personal safety
▶ Use the product only when it is in technically faultless condition.
▶ Never tamper with or modify the tool in any way.
▶ When chiseling into ceilings, walls and floors, always make sure that you have a safe and firm stance. A
sudden break-through can affect your balance!
▶ Apply appropriate safety measures at the opposite side of the workpiece in work that involves breaking
through. Parts breaking away could fall out and / or fall down causing injury to other persons.
▶ You and any other persons in the vicinity must wear suitable eye protection, a hard hat, ear protection,
protective gloves and respiratory protection while the tool is in use.
▶ Wear protective gloves also when changing the accessory tool. Touching the accessory tool can result
in cuts and burns.
▶ Wear eye protection. Flying fragments can injure the body and eyes.
▶ Before starting work, check the hazard class of the dust that will be produced when working. Use
an industrial vacuum cleaner with an officially approved protection class in compliance with the locally
applicable dust protection regulations. Dust from materials such as lead-based paint, certain types of
wood and concrete/masonry/stone containing quartz, minerals or metal can be harmful to health.
▶ Make sure that the workplace is well ventilated and, where necessary, wear a respirator appropriate for
the type of dust generated. Contact with or inhalation of the dust may cause allergic reactions and/or
respiratory or other diseases among operators or bystanders. Certain kinds of dust are classified as
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
*2240497*
2240497 English 5
carcinogenic such as oak and beech dust, especially in conjunction with additives for wood conditioning
(chromate, wood preservative). Material containing asbestos may be handled only by specialists.
▶ Take breaks and do physical exercises to improve the blood circulation in your fingers. Exposure to
vibration during long periods of work can lead to disorders of the blood vessels and nervous system in
the fingers, hands and wrists.
Electrical safety
▶ Before beginning work, check the working area for concealed electric cables or gas and water pipes.
External metal parts of the power tool can become live, presenting a risk of electric shock, if you
accidentally damage an electric cable.
Careful handling and use of electric tools
▶ Wait until the power tool stops completely before you lay it down.
2.4 Battery use and care
▶ Observe the special regulations and instructions applicable to the transport, storage and use of Li-ion
batteries.
▶ Do not expose batteries to high temperatures, direct sunlight or fire.
▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C.
▶ Do not use or charge batteries that have suffered mechanical impact, have been dropped from a height
or show signs of damage. In this case, always contact your Hilti Service.
▶ If the battery is too hot to touch it may be defective. In this case, place the product in a non-flammable
location, well away from flammable materials, where it can be kept under observation and allowed to
cool down. In this case, always contact your Hilti Service.
3 Description
3.1 Product overview 1
@
Chuck
;
Function selector switch
=
Lockbutton for sustained operation (chiseling
only)
%
Control switch
&
Charge-status and fault indicator (Li-ion bat-
tery)
(
Release buttons (also used to activate the
charge status indicator)
)
Battery
+
Side handle
§
On/off switch
/
Button for half power
:
Half-power indicator
∙
Service indicator
$
ON/OFF indicator
3.2 Intended use
The product described is a cordless (battery-powered) breaker with pneumatic hammering mechanism. The
product designed for light to medium chiseling work on masonry and surface finishing work on concrete.
▶ Use only Hilti Li-ion batteries from the B 36 series with this product.
▶ Use only the Hilti battery chargers from the C4/36 series for these batteries.
3.2.1 Possible misuse
• This product is not suitable for working on hazardous materials.
• This product is not suitable for working in a damp environment.
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
6 English 2240497
*2240497*
3.3 Active Vibration Reduction
The tool is equipped with an Active Vibration Reduction (AVR) system which reduces vibration noticeably.
3.4 Service indicator
The product is equipped with a service indicator LED.
3.4.1 MMI
Status Meaning
The Service indicator lights up.
Servicing is due.
The Service indicator flashes.
Have the product repaired by Hilti Service.
The ON/OFF indicator lights up. The product is switched on
The ON/OFF indicator flashes. The product is switched off because of a transient
fault.
The ON/OFF indicator is off. The product is switched off.
The Half power indicator lights up.
The product is working at half power.
The Half power indicator is off.
The product is working at full power.
3.4.2 Lithiumion battery status display
The Li-ion battery state of charge and malfunctions of the power tool are indicated by the display on the Liion
battery. The Liion battery state of charge is displayed after pressing one of the two battery release buttons.
Status Meaning
4 LEDs light. State of charge: 75 % to 100 %
3 LEDs light. State of charge: 50 % to 75 %
2 LEDs light. State of charge: 25 % to 50 %
1 LED lights. State of charge: 10 % to 25 %
1 LED blinks. State of charge: < 10 %
1 LED flashes, the product is not in working order. The battery has overheated or is completely dis-
charged.
4 LEDs flash, the product is not in working order. The power tool is overloaded or has overheated.
Battery state of charge cannot be displayed while the control switch is pressed and for up to 5 seconds
after releasing the control switch.
If the battery display LEDs blink, please observe the instructions given in the Troubleshooting section.
3.5 Items supplied
Breaker, side handle, operating instructions.
Other system products approved for use with this product can be found at your local Hilti Store or online at:
www.hilti.group.
4 Technical data
TE 500-A36
Rated voltage
36 V
Weight in accordance with EPTA procedure 01
7.9 kg
Chuck
TEY
Storage temperature
−20 ℃ … 70 ℃
Ambient temperature for operation
−17 ℃ … 60 ℃
4.1 Noise information and vibration values in accordance with EN 60745
The sound pressure and vibration values given in these instructions were measured in accordance with a
standardized test and can be used to compare one power tool with another. They can also be used for a
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
*2240497*
2240497 English 7
preliminary assessment of exposure. The data given represents the main applications of the power tool.
However, if the power tool is used for different applications, with different accessory tools, or is poorly
maintained, the data can vary. This can significantly increase exposure over the total working period. An
accurate estimation of exposure should also take into account the times when the tool is switched off, or
when it is running but not actually being used for a job. This can significantly reduce exposure over the
total working period. Identify additional safety measures to protect the operator from the effects of noise
and/or vibration, for example: Maintaining the power tool and accessory tools, keeping the hands warm,
organization of work patterns.
Noise emission values in accordance with EN 60745
TE 500-A36
Sound pressure level (LpA)
89 dB
Uncertainty for the sound pressure level (KpA)
3 dB
Sound power level (LWA)
100 dB
Uncertainty for the sound power level (KWA)
3 dB
Total vibration in accordance with EN 62841
TE 500-A36
Uncertainty (K)
1.5 m/s²
Chiseling in concrete (a
h, CHeq
)
6.7 m/s²
Uncertainty (K)
1.5 m/s²
5 Battery
Battery operating voltage
36 V
Ambient temperature for operation
−17 ℃ … 60 ℃
Storage temperature
−20 ℃ … 40 ℃
Battery charging starting temperature
−10 ℃ … 45 ℃
6 Operation
6.1 Preparations at the workplace
Switch the product off or remove the battery before making adjustments or changing accessories.
Observe the safety instructions and warnings in this documentation and on the product.
6.1.1 Inserting the battery
CAUTION
Risk of injury by short circuit or falling battery!
▶ Before inserting the battery, make sure that the contacts on the battery and the contacts on the product
are free of foreign matter.
▶ Make sure that the battery always engages correctly.
1. Charge the battery fully before using it for the first time.
2. Push the battery into the battery holder until it engages with an audible click.
3. Check that the battery is seated securely.
6.1.2 Removing the battery
1. Press the release buttons on the battery.
2. Pull the battery out of its holder in the device.
6.1.3 Charging the battery
1. Before charging the battery, read the operating instructions for the charger.
2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
3. Use an approved charger to charge the battery.
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
8 English 2240497
*2240497*
6.1.4 Fitting the side handle 2
CAUTION
Risk of injury! Loss of control over the breaker.
▶ Check that the side handle is fitted correctly and tightened securely.
1. Switch off the power tool.
2. Release the side handle clamping band by turning the handle grip.
3. Slide the side handle clamping band over the chuck from the front and into the recess provided.
4. Set the side handle to the desired position.
5. Tighten the side handle clamping band by turning the handle grip.
6.1.5 Setting the power level
After the battery is inserted, the product is always set by default to full power.
1. Press the "button for half power". The product runs at half power.
➥ The "half power indicator" lights up.
2. Press the "button for half power" again. The product runs at full power.
➥ The "half power indicator" goes out.
6.1.6 Inserting / removing the accessory tool 3
DANGER
Risk of fire! Risk of contact between the hot accessory tool and highly inflammable materials.
▶ Do not lay the hot accessory tool down on highly inflammable materials.
WARNING
Risk of injury! The tool becomes hot as a result of use.
▶ Wear protective gloves when changing the tool.
The use of unsuitable grease can cause damage to the product. Use only genuine Hilti grease.
1. Apply a little grease to the connection end of the accessory tool.
➥ Use only genuine Hilti grease. Using the wrong grease can result in damage to the product.
2.
Set the function selector switch to the “Chiseling” position .
3. Push the accessory tool into the chuck as far as it will go (until it engages).
4. After fitting the accessory tool, grip it and pull it in order to check that it is securely engaged.
➥ The product is ready for use.
5. Pull the chuck ring back as far as it will go and remove the accessory tool.
6.2 Types of work
CAUTION
Risk of injury! Loss of control over the breaker.
▶ Check that the side handle is fitted correctly and tightened securely.
Observe the safety instructions and warnings in this documentation and on the product.
6.3 Chisel positioning 4
CAUTION
Risk of injury! Loss of control over the chisel direction.
▶ Do not operate the tool when the selector switch is set to “Chisel positioning”. Turn the function selector
switch until it engages in the “Chiseling” position.
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
*2240497*
2240497 English 9
The chisel can be set to 24 different positions (in 15° increments). This ensures that flat chisels and
shaped chisels can always be set to the optimum working position.
1. Switch off the power tool.
2.
Set the function selector switch to the "Chisel positioning” position .
3. Turn the chisel to the desired position.
4.
Set the function selector switch to this symbol: until it engages.
➥ The product is ready for use.
6.3.1 Chiseling
▶
Set the function selector switch to the "Chiseling" position .
Use both hands to hold the product firmly. Keep the product clean and free of oil and grease.
When the product is hot after working, do not place it on readily flammable materials. These
materials can ignite.
6.3.2 Switch sustained operation on and off 5
When chiseling, the control switch can be locked in the “on” position.
1. Push the lockbutton for continuous operation forward.
2. Press the control switch fully.
➥ The product then runs in sustained operating mode.
3. Push the lockbutton for continuous operation back.
➥ The product switches off.
7 Care and maintenance
WARNING
Risk of injury with battery inserted !
▶ Always remove the battery before carrying out care and maintenance tasks!
Care and maintenance of the tool
• Carefully remove stubborn dirt.
• Clean the air vents carefully with a dry brush.
• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as
these can attack the plastic parts.
Care of the Liion batteries
• Keep the battery free from oil and grease.
• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as
these may attack the plastic parts.
• Avoid ingress of moisture.
Maintenance
• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all
function correctly.
• Do not operate the product if signs of damage are found or if parts malfunction. Have it repaired
immediately by Hilti Service.
• After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.
To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare
parts, consumables and accessories approved by Hilti for use with the product can be found at your
local Hilti Store or online at: www.hilti.group.
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
10 English 2240497
*2240497*
8 Transport and storage of cordless tools
Transport
CAUTION
Accidental starting during transport !
▶ Always transport your products with the batteries removed!
▶ Remove the battery.
▶ Never transport batteries in bulk form (loose, unprotected).
▶ Check the tool and batteries for damage before use after long periods of transport.
Storage
CAUTION
Accidental damage caused by defective or leaking batteries !
▶ Always store your products with the batteries removed!
▶ Store the tool and batteries in a place that is as cool and dry as possible.
▶ Never store batteries in direct sunlight, on heating units or behind a window pane.
▶ Store the tool and batteries in a place where they cannot be accessed by children or unauthorized
persons.
▶ Check the tool and batteries for damage before use after long periods of storage.
9 Troubleshooting
If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by
yourself, please contact Hilti Service.
9.1 Troubleshooting
Trouble or fault Possible cause Action to be taken
No hammering action. The product is too cold. ▶ Bring the product into contact
with the working surface, switch
it on and allow it to idle. If
necessary, repeat the procedure
until the hammering mechanism
begins to operate.
The battery runs down more
quickly than usual.
Battery condition is not optimal. ▶ Replace the battery.
The battery does not en-
gage with an audible "double
click".
The retaining lugs on the battery
are dirty.
▶ Clean the retaining lugs and refit
the battery.
Product switches off auto-
matically.
The overload protection system is
active.
The ON/OFF indicator flashes.
▶ Release the control switch.
Allow the product to cool down.
Press the control switch again.
Reduce the load on the tool.
The power tool or battery
gets very hot.
Electrical fault. ▶ Immediately switch off the
product. Remove the battery
and keep it under observation.
Allow it to cool down. Contact
Hilti service.
The product is overloaded (appli-
cation limit exceeded).
▶ Select a product that is suitable
for the intended purpose.
No response from the LEDs
on the battery.
The battery is not fully inserted. ▶ Push the battery in until it
engages with a double click.
The battery is discharged. ▶ Change the battery and charge
the empty battery.
The battery is too hot or too cold. ▶ Bring the battery to the recom-
mended working temperature.
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
*2240497*
2240497 English 11
Trouble or fault Possible cause Action to be taken
1 LED on the battery flashes. The battery is discharged. ▶ Change the battery and charge
the empty battery.
The battery is too hot or too cold. ▶ Bring the battery to the recom-
mended working temperature.
4 LEDs on the battery flash. Product momentarily overloaded. ▶ Release the control switch and
then press it again.
Protection against overheating. ▶ Allow the product to cool down
and clean the air vents.
Product does not develop full
power.
The control switch is not fully
pressed.
▶ Press the control switch as far
as it will go.
The half-power button is engaged. ▶ Press the "half-power" button.
The insert tool cannot be re-
leased from the chuck.
The chuck is not pulled back fully. ▶ Pull the chuck back as far
as it will go and remove the
accessory tool.
The side handle is not fitted cor-
rectly.
▶ Disengage the side handle and
refit it correctly so that the
clamping band and side handle
engage in the recess.
Product does not start. The electronic restart interlock is
activated after an interruption in
the electric supply.
▶ Switch the product off and then
on again.
The service indicator lights. Service limit time reached. ▶ Have the product repaired by
Hilti Service.
The service indicator blinks. The product is faulty. ▶ Have the product repaired by
Hilti Service.
The ON/OFF indicator
flashes.
Product momentarily overloaded. ▶ Release the control switch and
then press it again.
Protection against overheating. ▶ Allow the product to cool down
and clean the air vents.
10 Disposal
Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The
materials must be correctly separated before they can be recycled. In many countries, your old tools,
machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative
for further information.
▶ Do not dispose of power tools, electronic equipment or batteries as household waste!
11 RoHS (Restriction of Hazardous Substances)
Click on the link to go to the table of hazardous substances: qr.hilti.com/r10130182.
There is a link to the RoHS table, in the form of a QR code, at the end of this document.
12 Manufacturer’s warranty
▶ Please contact your local Hilti representative if you have questions about the warranty conditions.
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
12 Dansk 2240497
*2240497*
1 Oplysninger vedrørende dokumentationen
1.1 Vedrørende denne dokumentation
• Læs denne dokumentation igennem før ibrugtagning. Det er en forudsætning for sikkert arbejde og
korrekt håndtering.
• Følg sikkerheds- og advarselshenvisningerne i denne dokumentation og på produktet.
• Opbevar altid brugsanvisningen sammen med produktet, og overdrag det kun til andre personer sammen
med denne anvisning.
1.2 Tegnforklaring
1.2.1 Advarsler
Advarsler advarer mod farer ved håndtering af produktet. Følgende signalord anvendes:
FARE
FARE !
▶ Betegner en umiddelbart truende fare, der kan medføre alvorlige kvæstelser eller døden.
ADVARSEL
ADVARSEL !
▶ Står ved en potentielt truende fare, der kan medføre alvorlige kvæstelser eller døden.
FORSIGTIG
FORSIGTIG !
▶ Betegner en potentielt farlig situation, der kan forårsage lettere personskader eller materielle skader.
1.2.2 Symboler i denne dokumentation
Følgende symboler anvendes i denne dokumentation:
Læs brugsanvisningen før brug
Anvisninger for anvendelse og andre nyttige oplysninger
Håndtering af genvindbare materialer
Elektriske maskiner og batterier må ikke bortskaffes som almindeligt husholdningsaffald
1.2.3 Symboler i illustrationer
Følgende symboler anvendes på illustrationer:
Disse tal henviser til de forskellige illustrationer i begyndelsen af brugsanvisningen
Nummereringen udtrykker arbejdstrinnenes rækkefølge på illustrationen og kan afvige fra arbejds-
trinnene i teksten
Positionsnumre anvendes i illustrationen Oversigt og refererer til tallene i symbolforklaringen i
afsnittet Produktoversigt
Dette symbol skal sikre skærpet opmærksomhed ved omgang med produktet.
1.3 Produktspecifikke symboler
1.3.1 Symboler på produktet
Følgende symboler kan forekomme på produktet:
Mejsling
Placering af mejsel
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
*2240497*
2240497 Dansk 13
Serviceindikator
Diameter
Nominelt omdrejningstal, ubelastet
Omdrejninger pr. minut
Jævnstrøm
Trådløs dataoverførsel
Lithium-ion-batteri
Anvendt Hilti lithium-ion-batteriserie. Overhold oplysningerne i kapitlet Tilsigtet anvendelse.
1.4 Tænd/sluk
Symboler
Produktet er tændt
Produktet er slukket
1.5 Produktoplysninger
-produkter er beregnet til professionel brug og må kun betjenes, efterses og vedligeholdes af
autoriseret og instrueret personale. Dette personale skal i særdeleshed informeres om de potentielle farer,
der er forbundet med anvendelsen af denne maskine. Der kan opstå farlige situationer ved anvendelse af
produktet og det tilhørende udstyr, hvis det anvendes af personer, der ikke er blevet undervist i dens brug,
eller hvis det ikke anvendes korrekt i henhold til forskrifterne i denne brugsanvisning.
Typebetegnelse og serienummer fremgår af typeskiltet.
▶ Notér serienummeret i den efterfølgende tabel. Du skal bruge produktoplysningerne ved henvendelser til
vores lokale afdeling eller vores serviceværksted.
Produktoplysninger
Mejselhammer TE 500A36
Generation 04
Serienummer
1.6 Overensstemmelseserklæring
Vi erklærer som eneansvarlige, at det beskrevne produkt er i overensstemmelse med gældende direktiver og
standarder. Sidst i dette dokument finder du et bilede af overensstemmelseserklæringen.
Den tekniske dokumentation er arkiveret her:
Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE
2 Sikkerhed
2.1 Generelle sikkerhedsanvisninger for elværktøj
ADVARSEL Læs alle sikkerhedsanvisninger, henvisninger, billedtekster og tekniske data på
elværktøjet. Hvis følgende anvisninger ikke overholdes, er der risiko for elektrisk stød, brand og/eller
alvorlige personskader.
Opbevar alle sikkerhedsanvisninger og instruktioner til senere brug.
Det benyttede begreb "elværktøj" i sikkerhedsanvisningerne refererer til elektriske maskiner (med netledning)
eller batteridrevne maskiner (uden netledning).
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
14 Dansk 2240497
*2240497*
Arbejdspladssikkerhed
▶ Sørg for at holde arbejdsområdet ryddeligt og godt oplyst. Uorden eller uoplyste arbejdsområder
øger faren for uheld.
▶ Brug ikke elværktøj i eksplosionstruede omgivelser, hvor der er brændbare væsker, gasser eller
støv. Elværktøj kan slå gnister, der kan antænde støv eller dampe.
▶ Sørg for, at andre personer og ikke mindst børn holdes væk fra arbejdsområdet, når elværktøjet
er i brug. Hvis man distraheres, kan man miste kontrollen over maskinen.
Elektrisk sikkerhed
▶ Elværktøjets stik skal passe til kontakten. Stikket må under ingen omstændigheder ændres. Brug
ikke adapterstik sammen med jordforbundne elværktøj. Uændrede stik, der passer til kontakterne,
nedsætter risikoen for elektrisk stød.
▶ Undgå kropskontakt med jordforbundne overflader som f.eks. rør, radiatorer, komfurer og
køleskabe. Hvis din krop er jordforbundet, øges risikoen for elektrisk stød.
▶ Elværktøj må ikke udsættes for regn eller fugt. Indtrængning af vand i elværktøj øger risikoen for
elektrisk stød.
▶ Brug ikke ledningen til formål, den ikke er beregnet til (f.eks. må man aldrig bære elværktøjet i
ledningen, hænge det op i ledningen eller rykke i ledningen for at trække stikket ud af kontakten).
Beskyt ledningen mod varme, olie, skarpe kanter eller dele, der er i bevægelse. Beskadigede eller
sammenviklede ledninger øger risikoen for elektrisk stød.
▶ Hvis elværktøjet benyttes i det fri, må der kun benyttes en forlængerledning, der er egnet til
udendørs brug. Brug af forlængerledning til udendørs brug nedsætter risikoen for elektrisk stød.
▶ Hvis det ikke kan undgås at anvende elværktøjet i fugtige omgivelser, skal du anvende et
fejlstrømsrelæ. Anvendelsen af et fejlstrømsrelæ nedsætter risikoen for et elektrisk stød.
Personlig sikkerhed
▶ Det er vigtigt at være opmærksom, se, hvad man laver, og bruge maskinen fornuftigt. Anvend aldrig
elværktøj, hvis du er træt eller påvirket af stoffer, alkohol eller medicin. Et øjebliks uopmærksomhed
under brugen af elværktøjet kan medføre alvorlige personskader.
▶ Brug beskyttelsesudstyr, og hav altid beskyttelsesbriller på. Brug af sikkerhedsudstyr som f.eks.
støvmaske, skridsikkert fodtøj, beskyttelseshjelm eller høreværn afhængigt af elværktøjets type og
anvendelse nedsætter risikoen for personskader.
▶ Undgå utilsigtet igangsætning. Kontrollér, at elværktøjet er frakoblet, før du slutter det til
strømforsyningen og/eller batteriet, tager det op eller transporterer det. Undgå at bære elværktøjet
med fingeren på afbryderen, og sørg for, at det ikke er tændt, når det sluttes til nettet, da dette øger
risikoen for personskader.
▶ Fjern indstillingsværktøj eller skruenøgler, inden elværktøjet tændes. Hvis et stykke værktøj eller en
nøgle sidder i en roterende maskindel, er der risiko for personskader.
▶ Undgå at arbejde i unormale kropsstillinger. Sørg for at stå sikkert, mens der arbejdes, og kom
ikke ud af balance. Det er derved nemmere at kontrollere elværktøjet, hvis der skulle opstå uventede
situationer.
▶ Brug egnet arbejdstøj. Undgå løse beklædningsgenstande eller smykker. Hold hår, tøj og handsker
væk fra dele, der bevæger sig. Dele, der er i bevægelse, kan gribe fat i løstsiddende tøj, smykker eller
langt hår.
▶ Hvis støvudsugnings- og opsamlingsudstyr kan monteres, er det vigtigt, at dette tilsluttes og
benyttes korrekt. Ved at anvende en støvudsugning er det muligt at nedsætte risiciene som følge af
støv.
▶ Man må ikke ignorere sikkerhedsreglerne for elværktøj, heller ikke selvom man er fortrolig med
brugen af elværktøjet. Uagtsomhed kan medføre alvorlig tilskadekomst inden for få sekunder.
Anvendelse og pleje af elværktøjet
▶ Undgå at overbelaste maskinen. Brug altid en maskine, der er beregnet til det stykke arbejde,
der skal udføres. Med det rigtige værktøj arbejder man bedst og mest sikkert inden for det angivne
effektområde.
▶ Brug ikke elværktøj, hvis afbryderen er defekt. En maskine, der ikke kan startes og stoppes, er farlig
og skal repareres.
▶ Træk stikket ud af stikkontakten, og/eller fjern batteriet fra maskinen, inden du foretager
indstillinger på den, skifter tilbehør og dele eller lægger den til side. Disse sikkerhedsforanstaltninger
forhindrer utilsigtet start af elværktøjet.
▶ Opbevar ubenyttede elværktøjer uden for børns rækkevidde. Lad aldrig personer, der ikke er
fortrolige med maskinen eller ikke har gennemlæst sikkerhedsanvisningerne, benytte denne.
Elværktøj er farligt, hvis det benyttes af ukyndige personer.
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
*2240497*
2240497 Dansk 15
▶ Sørg for at pleje elværktøj omhyggeligt. Kontrollér, om bevægelige dele fungerer korrekt og
ikke sidder fast, og om delene er brækket eller beskadiget, således at elværktøjets funktion
påvirkes. Få beskadigede dele repareret, inden elværktøjet tages i brug. Mange uheld skyldes
dårligt vedligeholdte elværktøjer.
▶
Sørg for, at skæreværktøjer er skarpe og rene. Omhyggeligt vedligeholdte skæreværktøjer med
skarpe skærekanter sætter sig ikke så hurtigt fast og er nemmere at føre.
▶ Anvend elværktøj, tilbehør, indsatsværktøj osv. i overensstemmelse med disse anvisninger. Tag
hensyn til arbejdsforholdene og det arbejde, der skal udføres. I tilfælde af anvendelse af maskinen til
formål, som ligger uden for det fastsatte anvendelsesområde, kan der opstå farlige situationer.
▶ Sørg for, at greb og gribeflader er tørre, rene og fri for olie og fedt. Glatte greb og gribeflader gør
betjeningen usikker, og det kan være svært at styre elværktøjet i uforudsete situationer.
Anvendelse og pleje af batteridrevet elværktøj
▶ Oplad kun batterier i ladere, der er anbefalet af fabrikanten. Der er risiko for brand, hvis en lader, der
er beregnet til et bestemt batteri, anvendes til opladning af en anden batteritype.
▶ Brug kun de batterier, der er beregnet til elværktøjet. Brug af andre batterier øger risikoen for
personskader og er forbundet med brandfare.
▶ Ikke benyttede batterier må ikke komme i berøring med kontorclips, mønter, nøgler, søm, skruer
eller andre små metalgenstande, da disse kan kortslutte kontakterne. En kortslutning mellem
batterikontakterne øger risikoen for personskader i form af forbrændinger.
▶ Hvis batteriet anvendes forkert, kan der løbe væske ud af batteriet. Undgå at komme i kontakt
med denne væske. Hvis det alligevel skulle ske, skylles med vand. Søg læge, hvis væsken kommer
i øjnene. Batterivæske kan give hudirritation eller forbrændinger.
▶ Brug aldrig et beskadiget eller ændret batteri. Beskadigede eller ændrede batterier kan virke utilsigtet
og medføre brand, eksplosion eller risiko for tilskadekomst.
▶ Batterier må ikke udsættes for åben ild eller høje temperaturer. Ild eller temperaturer over 130 °C
(265 °F) kan medføre eksplosion.
▶ Følg alle anvisninger vedrørende opladning, og oplad aldrig batteriet eller det batteridrevne
værktøj uden for det temperaturområde, der er anført i betjeningsvejledningen. Forkert opladning
eller opladning uden for det tilladte temperaturområde kan ødelægge batteriet og øge risikoen for brand.
Service
▶ Sørg for, at elværktøjet kun repareres af kvalificerede fagfolk, og at der altid benyttes originale
reservedele. Dermed sikres størst mulig elværktøjssikkerhed.
▶ Forsøg aldrig at reparere beskadigede batterier. Al vedligeholdelse af batterier skal foretages af
producenten eller af autoriserede forhandlere.
2.2 Sikkerhedsanvisninger til hamre
Sikkerhedsanvisninger for alle opgaver
▶ Brug høreværn. Støjpåvirkningen kan medføre høretab.
▶ Brug de ekstrahåndgreb, som følger med maskinen. Hvis du mister kontrollen, kan det medføre
personskader.
▶ Hold maskinen på de isolerede grebsflader, når du udfører opgaver, hvor indsatsværktøjet kan
ramme skjulte strømledninger. Ved kontakt med en spændingsførende ledning kan også metalliske
værktøjsdele sættes under spænding, hvilket kan medføre elektrisk stød.
2.3 Yderligere sikkerhedsanvisninger, mejselhammer
Personlig sikkerhed
▶ Anvend kun produktet i teknisk fejlfri stand.
▶ Foretag aldrig manipulationer eller ændringer på maskinen.
▶ Ved mejsling af lofter, vægge og gulve er det vigtigt at stå sikkert og stabilt. Hvis værktøjet pludselig går
igennem, kan du miste balancen!
▶ Ved gennembrydningsarbejde skal du huske at sikre området på den modsatte side. Nedbrydningsdele
kan falde ud og/eller ned og volde skade på andre personer.
▶ Sørg for, at du selv og personer, som opholder sig i nærheden under brugen af maskinen, anvender
egnede beskyttelsesbriller, sikkerhedshjelm, høreværn, beskyttelseshandsker og et let åndedrætsværn.
▶ Brug også beskyttelseshandsker, når du skifter værktøj. Berøring af indsatsværktøjet kan medføre snitsår
og forbrændinger.
▶ Brug øjenværn. Splinterne fra materialet kan medføre skader på legeme og øjne.
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
16 Dansk 2240497
*2240497*
▶ Find ud af, hvilken fareklasse det støv, der opstår ved arbejdet, har, inden du går i gang med arbejdet.
Anvend en industristøvsuger med en officielt tilladt beskyttelsesklassificering, som opfylder de lokale
støvbeskyttelsesbestemmelser. Støv fra materialer såsom blyholdig maling, visse træsorter, beton /
murværk / natursten, som indeholder kvarts, og mineraler samt metal kan være sundhedsfarlige.
▶
Sørg for en god ventilation af arbejdspladsen, og brug om nødvendigt et åndedrætsværn, som egner sig
til den pågældende støvtype. Berøring eller indånding af støv kan medføre allergiske reaktioner og/eller
luftvejssygdomme hos brugeren eller personer, der opholder sig i nærheden. Bestemte støvtyper,
f.eks. støv fra ege- og bøgetræ, er kræftfremkaldende, især i forbindelse med tilsætningsstoffer til
træbehandling (kromat, træbeskyttelsesmidler). Asbestholdige materialer må kun håndteres af fagfolk.
▶ Hold pauser under arbejdet, og lav øvelser, så dine fingre får en bedre blodgennemstrømning. Ved
længerevarende arbejde kan vibrationermedføre forstyrrelser af fingrenes, hændernes eller håndleddenes
blodkar og nervesystem.
Elektrisk sikkerhed
▶ Kontrollér før påbegyndelse af arbejdet arbejdsområdet for skjulte elektriske ledninger, gas- og vandrør,
f.eks. med en metaldetektor. Udvendige metaldele på maskinen kan medføre elektrisk stød, hvis du ved
en fejl kommer til at beskadige en elledning.
Omhyggelig omgang med og brug af elværktøj
▶ Vent, indtil elværktøjet er standset helt, før du lægger det fra dig.
2.4 Omhyggelig omgang med og brug af batterier
▶ Læs de særlige retningslinjer for transport, opbevaring og brug af lithiumion-batterier.
▶ Hold batterier på sikker afstand af høje temperaturer, direkte solindstråling og ild.
▶ Batterierne må ikke adskilles, klemmes, opvarmes til over 80 °C eller brændes.
▶ Anvend og oplad ikke batterier, som har fået et slag, er faldet på gulvet fra mere end en meters højde
eller på anden vis er blevet beskadiget. Kontakt i så fald altid Hilti Service.
▶ Hvis batteriet er for varmt til at kunne røres, kan det være defekt. Placer produktet på et ikke-brændbart
sted i tilstrækkelig afstand til brændbare materialer, hvor det er muligt at holde øje med det, og lad det
køle af. Kontakt i så fald altid Hilti Service.
3 Beskrivelse
3.1 Produktoversigt 1
@
Værktøjsholder
;
Funktionsvælger
=
Låseknap til permanent drift (kun mejsling)
%
Afbryder
&
Ladetilstands- og fejlvisning (lithium-ion-
batteri)
(
Frigøringsknapper med ekstrafunktion til
aktivering af ladetilstandsvisning
)
Batteri
+
Sidegreb
§
Tænd/sluk-knap
/
Knap til halv effekt
:
Visning for halv effekt
∙
Serviceindikator
$
Til/Fra-indikator
3.2 Bestemmelsesmæssig anvendelse
Det beskrevne produkt er en batteridrevet mejselhammer med pneumatisk slagmekanisme. Produktet er
beregnet til lette og moderate mejselopgaver i murværk og til efterbearbejdning af beton.
▶ Anvend kun Hilti lithium-ion-batterier i typeserien B 36 til dette produkt.
▶ Anvend kun Hilti ladere i C4/36-serien til disse batterier.
Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/