Hilti TE 300­-A36 SDS Plus Breaker ユーザーマニュアル

カテゴリー
パワードリル
タイプ
ユーザーマニュアル
TE 300A36
English 1
Dansk 11
Svenska 21
Norsk 31
Suomi 41
Eesti 52
Latviešu 62
Lietuvių 72
Türkçe 83
ﻲ 94
日本語 105
한국어 115
繁體中文 125
中文 134
1
2
3
4
5
TE 300A36
en Originaloperatinginstructions....................................... 1
da Originalbrugsanvisning .......................................... 11
sv Originalbruksanvisning........................................... 21
no Originalbruksanvisning .......................................... 31
fi Alkuperäisetohjeet ............................................. 41
et Originaalkasutusjuhend .......................................... 52
lv Oriģinālālietošanasinstrukcija ..................................... 62
lt Originalinaudojimoinstrukcija...................................... 72
tr Orijinalkullanımkılavuzu ......................................... 83
ar .......................................... 94
ja 書 ............................................ 105
ko ............................................. 115
zh .................................................. 125
cn .................................................. 134
*2201963* 2201963 English 1
Original operating instructions
1 Information about the operating instructions
1.1 About these operating instructions
Read these operating instructions before the product is used or operated for the first time. This is a
prerequisite for safe, trouble-free handling and use of the product.
Observe the safety instructions and warnings in these operating instructions and on the product.
Always keep the operating instructions with the product and make sure that the product is accompanied
by these operating instructions only, when the product is given to other persons.
1.2 Explanation of symbols used
1.2.1 Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words
are used:
DANGER
DANGER !
Draws attention to imminent danger that will lead to serious personal injury or fatality.
WARNING
WARNING !
Draws attention to a potential threat of danger that can lead to serious injury or fatality.
CAUTION
CAUTION !
Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the
equipment or other property.
1.2.2 Symbols in the documentation
The following symbols are used in this document:
Read the operating instructions before use.
Instructions for use and other useful information
Dealing with recyclable materials
Do not dispose of electric equipment and batteries as household waste
1.2.3 Symbols in the illustrations
The following symbols are used in illustrations:
These numbers refer to the corresponding illustrations found at the beginning of these operating
instructions
The numbering reflects the sequence of operations shown in the illustrations and may deviate
from the steps described in the text
Item reference numbers are used in the overview illustrations and refer to the numbers used in
the product overview section
This symbol is intended to draw special attention to certain points when handling the product.
2 English 2201963 *2201963*
1.3 Product-dependent symbols
1.3.1 Symbols on the product
The following symbols are used on the product:
Chiseling
Chisel positioning
Diameter
Rated speed under no load
Revolutions per minute
Direct current (DC)
Li-ion battery
Hilti Li-ion battery type series used. Observe the information given in the section headed In-
tended use.
The product supports wireless data transmission compatible with iOS and Android platforms.
Never use the battery as a striking tool.
Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any
other way.
1.4 Product information
products are designed for professional users and only trained, authorized personnel are
permitted to operate, service and maintain the products. This personnel must be specifically informed about
the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by
untrained personnel or if used not in accordance with the intended use.
The type designation and serial number are printed on the rating plate.
Write down the serial number in the table below. You will be required to state the product details when
contacting Hilti Service or your local Hilti organization to inquire about the product.
Product information
Breaker TE 300A36
Generation 03
Serial no.
1.5 Declaration of conformity
We declare, on our sole responsibility, that the product described here complies with the applicable directives
and standards. A copy of the declaration of conformity can be found at the end of this documentation.
The technical documentation is filed here:
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany
2 Safety
2.1 General power tool safety warnings
WARNING Read all safety warnings, instructions, illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
*2201963* 2201963 English 3
Work area safety
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
Electrical safety
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the
risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
Personal safety
Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as a
dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will
reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power
source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on
the switch or energising power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and collection facilities, ensure these
are connected and properly used. Use of dust collection can reduce dust-related hazards.
Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore
tool safety principles. A careless action can cause severe injury within a fraction of a second.
Power tool use and care
Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or remove the battery pack, if detachable, from
the power tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
Maintain power tools and accessories. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained power
tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
4 English 2201963 *2201963*
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
Battery tool use and care
Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with another battery pack.
Use power tools only with specifically designated battery packs. Use of any other battery packs may
create a risk of injury and fire.
When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects, that can make a connection from one terminal to
another. Shorting the battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may
exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature
above 130° C (265 °F) may cause explosion.
Follow all charging instructions and do not charge the battery pack or tool outside the temperature
range specified in the instructions. Charging improperly or at temperatures outside the specified range
may damage the battery and increase the risk of fire.
Service
Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
Never service damaged battery packs. Service of battery packs should only be performed by the
manufacturer or authorized service providers.
2.2 Hammer safety warnings
Wear ear protectors. Exposure to noise can cause hearing loss.
Use auxiliary handles, if supplied with the tool. Loss of control can cause personal injury.
Hold power tool by insulated gripping surfaces, when performing an operation where the cutting
accessory may contact hidden wiring.. Cutting accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the operator an electric shock.
2.3 Additional safety instructions for breakers
Personal safety
Use the product and accessories only when they are in perfect working order.
Never tamper with or modify the product or accessories in any way.
When chiseling into ceilings, walls and floors, always make sure that you have a safe and firm stance. A
sudden break-through can affect your balance!
Apply appropriate safety measures at the opposite side of the workpiece in work that involves breaking
through. Parts breaking away could fall out and / or fall down causing injury to other persons.
You and the other persons in the vicinity must wear suitable eye protection, a hard hat, ear protection,
protective gloves and light respiratory protection while the product is in use.
Wear protective gloves when changing the accessory tool. Touching the accessory tool can result in
cuts and burns.
Wear eye protection. Flying fragments can injure the body and eyes.
Dust produced by grinding, sanding, cutting and drilling can contain dangerous chemicals. Some
examples are: lead or lead-based paints; brick, concrete and other masonry products, natural stone
and other products containing silicates; certain types of wood, such as oak, beech and chemically
treated wood; asbestos or materials that contain asbestos. Determine the exposure of the operator and
bystanders by means of the hazard classification of the materials to be worked. Implement the necessary
measures to restrict exposure to a safe level, for example by the use of a dust collection system or by
the wearing of suitable respiratory protection. The general measures for reducing exposure include:
working in an area that is well ventilated,
avoidance of prolonged contact with dust,
*2201963* 2201963 English 5
directing dust away from the face and body,
wearing protective clothing and washing exposed areas of the skin with water and soap.
Take frequent breaks and do physical exercises to improve the blood circulation in your fingers. High
vibration during long periods of work can lead to disorders of the blood vessels and nervous system in
the fingers, hands and wrists.
Electrical safety
Before beginning work, check the working area for concealed electric cables or gas and water pipes.
External metal parts of the product could give you an electric shock or cause an explosion if you
accidentally damage an electric cable or a gas or water pipe.
Power tool use and care
Wait until the product has come to a complete stop before you lay it down.
2.4 Careful handling and use of batteries
Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.
Do not expose batteries to high temperatures, direct sunlight or fire.
Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C
(176 °F).
Do not use or charge batteries that have suffered mechanical impact, have been dropped from a height
or show signs of damage. In this case, always contact your Hilti Service.
If the battery is too hot to touch it may be defective. Put the battery in a place where it is clearly visible
and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to
cool down. If it is still too hot to touch after an hour, the battery is faulty. Contact Hilti Service.
3 Description
3.1 Overview of the product 1
@Chuck
;Function selector switch
=Control switch
%Battery state of charge / fault display
&Release buttons / battery state of charge
display
(Battery
3.2 Intended use
The product described is a cordless (battery-powered) breaker with pneumatic hammering mechanism. The
product designed for light to medium chiseling work on masonry and surface finishing work on concrete.
Use only Hilti Li-ion batteries from the B 36 series with this product.
Use only the Hilti battery chargers from the C4/36 series for these batteries.
3.3 Possible misuse
This product is not suitable for working on hazardous materials.
This product is not suitable for working in a damp environment.
Do not use the product where there is a risk of fire or explosion.
3.4 Lithiumion battery status display
The Li-ion battery state of charge and malfunctions of the power tool are indicated by the display on the Liion
battery. The Liion battery state of charge is displayed after pressing one of the two battery release buttons.
6 English 2201963 *2201963*
Status Meaning
4 LEDs light. State of charge: 75 % to 100 %
3 LEDs light. State of charge: 50 % to 75 %
2 LEDs light. State of charge: 25 % to 50 %
1 LED lights. State of charge: 10 % to 25 %
1 LED blinks. State of charge: < 10 %
1 LED flashes, the power tool is not in working or-
der. The battery has overheated or is completely dis-
charged.
4 LEDs flash, the power tool is not in working or-
der. The power tool is overloaded or has overheated.
Battery state of charge cannot be displayed while the control switch is pressed and for up to 5 seconds
after releasing the control switch.
If the battery display LEDs blink, please observe the instructions given in the Troubleshooting section.
3.5 Items supplied
Breaker, side handle, operating instructions.
Other system products approved for use with this product can be found at your local Hilti Store or online at:
www.hilti.group | USA: www.hilti.com.
4 Technical data
4.1 Product data
TE 300A36
Rated voltage 36 V
Weight in accordance with EPTA procedure 01, measured with B36⁄5.2 4.9 kg
4.2 Noise information and vibration values in accordance with EN 60745
The sound pressure and vibration values given in these instructions were measured in accordance with a
standardized test and can be used to compare one power tool with another. They can also be used for a
preliminary assessment of exposure. The data given represents the main applications of the power tool.
However, if the power tool is used for different applications, with different accessory tools, or is poorly
maintained, the data can vary. This can significantly increase exposure over the total working period. An
accurate estimation of exposure should also take into account the times when the tool is switched off, or
when it is running but not actually being used for a job. This can significantly reduce exposure over the
total working period. Identify additional safety measures to protect the operator from the effects of noise
and/or vibration, for example: Maintaining the power tool and accessory tools, keeping the hands warm,
organization of work patterns.
Noise information
TE 300A36
Sound power level (LWA)99 dB
Uncertainty (KWA)3 dB(A)
Sound pressure level (L, pA)88 dB
Uncertainty (KpA)3 dB(A)
Information about vibration
TE 300A36
Chiseling (ah, Cheq)7.9 m/s²
Uncertainty 1.5 m/s²
*2201963* 2201963 English 7
4.3 Battery
Battery operating voltage 36 V
Ambient temperature for operation −17 ℃ … 60 ℃
Storage temperature −20 ℃ … 40 ℃
Battery charging starting temperature −10 ℃ … 45 ℃
5 Preparations at the workplace
WARNING
Risk of injury by inadvertent starting!
Before inserting the battery, make sure that the product is switched off.
Remove the battery before making any adjustments to the power tool or before changing accessories.
Observe the safety instructions and warnings in this documentation and on the product.
5.1 Charging the battery
1. Before charging the battery, read the operating instructions for the charger.
2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
3. Use an approved charger to charge the battery. → page 5
5.2 Inserting the battery
WARNING
Risk of injury by short circuit or falling battery!
Before inserting the battery, make sure that the contacts on the battery and the contacts on the product
are free of foreign matter.
Make sure that the battery always engages correctly.
1. Charge the battery fully before using it for the first time.
2. Push the battery into the product until it engages with an audible click.
3. Check that the battery is seated securely.
5.3 Removing the battery
1. Press the battery release buttons.
2. Remove the battery from the tool.
5.4 Fitting the side handle (optional) 2
CAUTION
Risk of injury! Loss of control over the breaker.
Check that the side handle is fitted correctly and tightened securely.
1. Release the side handle clamping band by turning the handle grip.
2. Slide the side handle clamping band over the tool holder from the front and into the recess provided.
3. Adjust the side handle to the desired position.
4. Tighten the side handle clamping band by turning the handle grip.
5.5 Removing the chuck 3
When changing the chuck, set the function selector switch to this position: .
1. Remove the battery from the tool.
2. Grip the chuck as shown in the illustration and pull the three chuck release rings upwards.
3. Lift the chuck upwards away from the tool.
8 English 2201963 *2201963*
5.6 Fitting the chuck 3
When changing the chuck, set the function selector switch to this position: .
1. Remove the battery from the tool.
2. Grip the chuck as shown in the illustration and pull the three chuck release rings upwards.
3. Fit the chuck onto the chuck mount.
4. Rotate the chuck until it engages in position.
5.7 Inserting the tool 4
1. Lightly grease the connection end of the accessory tool.
Use only genuine Hilti grease. Using the wrong grease can result in damage to the tool.
2. Push the accessory tool into the chuck as far as it will go (until it engages).
3. After fitting the accessory tool, grip it and pull it in order to check that it is securely engaged.
The product is ready for use.
5.8 Removing the accessory tool 4
WARNING
Risk of injury! The tool becomes hot as a result of use.
Wear protective gloves when changing the tool.
Pull the tool lock back as far as it will go and remove the accessory tool.
6 Types of work
CAUTION
Risk of damage by incorrect handling!
Do not operate the switches for direction of rotation and/or function selection during operation.
Observe the safety instructions and warnings in this documentation and on the product.
6.1 Function selector switch 5
Set the function selector switch to the desired position.
6.2 Chisel positioning
Set the function selector switch to this symbol: .
The chisel can be adjusted to 12 different positions (in 30° increments). This ensures that flat chisels
and shaped chisels can always be set to the optimum working position.
6.3 Chiseling
Set the function selector switch to this symbol: .
Use both hands to hold the product firmly. Keep the product clean and free of oil and grease.
When the product is hot after working, do not place it on readily flammable materials. These
materials can ignite.
7 Care and maintenance
WARNING
Risk of injury with battery inserted !
Always remove the battery before carrying out care and maintenance tasks!
*2201963* 2201963 English 9
Care of the product
Carefully remove stubborn dirt.
Carefully clean the air vents, if present, with a dry, soft brush.
Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as
these can attack the plastic parts.
Use a dry, clean cloth to clean the contacts of the product.
Care of the Liion batteries
Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush.
Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of
moisture (e.g. by being dipped in water or left in the rain).
If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable
container and consult Hilti Service.
Keep the battery free of extraneous oil and grease. Do not permit dust or dirt to accumulate unnecessarily
on the battery. Clean the battery with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents
containing silicone as these can attack the plastic parts.
Do not touch the contacts of the battery and do not remove the factory-applied grease from the contacts.
Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as
these can attack the plastic parts.
Maintenance
Check all visible parts and controls for signs of damage at regular intervals and make sure that they all
function correctly.
Do not use the product if signs of damage are found or if parts malfunction. Immediately have the product
repaired by Hilti Service.
After cleaning and maintenance, install all guards and protective devices and check that they are in full
working order.
To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare
parts, consumables and accessories approved by Hilti for use with your product can be found at your
Hilti Store or online at: www.hilti.group
8 Transport and storage of cordless tools and batteries
Transport
CAUTION
Accidental starting during transport !
Always transport your products with the batteries removed!
Remove the battery/batteries.
Never transport batteries loose and unprotected. During transport, batteries should be protected from
excessive shock and vibration and isolated from any conductive materials or other batteries that may
come in contact with the terminals and cause a short circuit. Comply with the locally applicable
regulations for transporting batteries.
Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged
batteries.
Prior to each use and before and after prolonged transport, check the product and the batteries for
damage.
Storage
WARNING
Accidental damage caused by defective or leaking batteries !
Always store your products with the batteries removed!
Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in
the technical data.
Do not store batteries on the charger. Always remove the battery from the charger when the charging
operation has completed.
Never leave batteries in direct sunlight, on sources of heat, or behind glass.
Store the product and batteries where they cannot be accessed by children or unauthorized persons.
10 English 2201963 *2201963*
Prior to each use and before and after prolonged storage, check the product and the batteries for
damage.
9 Troubleshooting
If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by
yourself, please contact Hilti Service.
9.1 The breaker is in working order
Trouble or fault Possible cause Action to be taken
The battery runs down more
quickly than usual. Battery condition is not optimal. Replace the battery.
The battery doesn’t engage
with an audible click. The retaining lugs on the battery
are dirty.
Clean the retaining lugs and refit
the battery.
The power tool doesn’t start. The permissible operating temper-
ature of the combihammer’s elec-
tronics has been exceeded.
Allow the combihammer to cool
down.
Battery is discharged. Change the battery and charge
the empty battery.
Product switches off auto-
matically. The overload cut-out has been
activated.
Release the control switch.
Allow the product to cool down.
Press the control switch again.
The power tool or battery
gets very hot. Electrical fault Immediately switch off the
product. Remove the battery
and keep it under observation.
Allow it to cool down. Contact
Hilti service.
The product is overloaded (appli-
cation limit exceeded).
Select a tool that is suitable for
the intended purpose.
The accessory tool can’t be
released. The chuck is not pulled back fully. Pull the tool lock back as far
as it will go and remove the
accessory tool.
9.2 The breaker is not in working order
Malfunction Possible cause Action to be taken
No LEDs light. The battery is not fully inserted. Push the battery in until it
engages with a click.
Battery is discharged. Change the battery and charge
the empty battery.
The battery is too hot or too cold. Bring the battery to the recom-
mended working temperature.
1 LED flashes. Battery is discharged. Change the battery and charge
the empty battery.
The battery is too hot or too cold. Bring the battery to the recom-
mended working temperature.
4 LEDs blink. Product momentarily overloaded. Release the control switch and
then press it again.
Protection against overheating. Allow the product to cool down
and clean the air vents.
10 Disposal
Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The
materials must be correctly separated before they can be recycled. In many countries, your old tools,
machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative
for further information.
*2201963* 2201963 Dansk 11
Do not dispose of power tools, electronic equipment or batteries as household waste!
11 Manufacturer’s warranty
Please contact your local Hilti representative if you have questions about the warranty conditions.
Original brugsanvisning
1 Om brugsanvisningen
1.1 Om denne brugsanvisning
Læs brugsanvisningen grundigt igennem inden ibrugtagning. Det er en forudsætning for sikkert arbejde
og korrekt håndtering.
Følg sikkerhedsanvisningerne og advarslerne i denne brugsanvisning og på produktet.
Opbevar altid brugsanvisningen sammen med produktet, og overdrag kun produktet til andre personer
sammen med denne brugsanvisning.
1.2 Tegnforklaring
1.2.1 Advarsler
Advarsler advarer mod farer ved håndtering af produktet. Følgende signalord anvendes:
FARE
FARE !
Betegner en umiddelbart truende fare, der kan medføre alvorlige kvæstelser eller døden.
ADVARSEL
ADVARSEL !
Står ved en potentielt truende fare, der kan medføre alvorlige kvæstelser eller døden.
FORSIGTIG
FORSIGTIG !
Advarer om en potentielt farlig situation, der kan forårsage personskader eller materielle skader.
1.2.2 Symboler i denne dokumentation
Følgende symboler anvendes i denne dokumentation:
Læs brugsanvisningen før brug
Anvisninger for anvendelse og andre nyttige oplysninger
Håndtering af genvindbare materialer
Elektriske maskiner og batterier må ikke bortskaffes som almindeligt husholdningsaffald
1.2.3 Symboler i illustrationer
Følgende symboler anvendes på illustrationer:
Disse tal henviser til de forskellige illustrationer i begyndelsen af brugsanvisningen
Nummereringen udtrykker arbejdstrinnenes rækkefølge på illustrationen og kan afvige fra arbejds-
trinnene i teksten
Positionsnumre anvendes i illustrationen Oversigt og refererer til tallene i symbolforklaringen i
afsnittet Produktoversigt
12 Dansk 2201963 *2201963*
Dette symbol skal sikre skærpet opmærksomhed ved omgang med produktet.
1.3 Produktspecifikke symboler
1.3.1 Symboler på produktet
Følgende symboler anvendes på produktet:
Mejsling
Placering af mejsel
Diameter
Nominelt omdrejningstal, ubelastet
Omdrejninger pr. minut
Jævnstrøm
Lithium-ion-batteri
Anvendt Hilti lithium-ion-batteriserie. Overhold oplysningerne i kapitlet Tilsigtet anvendelse.
Produktet understøtter trådløs dataoverførsel, som er kompatibel med iOS- og Android-platforme.
Brug aldrig batteriet som slagværktøj.
Lad ikke batteriet falde på gulvet. Brug ikke et batteri, der har fået et slag eller på anden vis er
beskadiget.
1.4 Produktoplysninger
-produkter er beregnet til professionel brug og må kun betjenes, efterses og vedligeholdes af
autoriseret og instrueret personale. Dette personale skal i særdeleshed informeres om de potentielle farer,
der er forbundet med anvendelsen af denne maskine. Der kan opstå farlige situationer ved anvendelse af
produktet og det tilhørende udstyr, hvis det anvendes af personer, der ikke er blevet undervist i dens brug,
eller hvis det ikke anvendes korrekt i henhold til forskrifterne i denne brugsanvisning.
Typebetegnelse og serienummer fremgår af typeskiltet.
Notér serienummeret i den efterfølgende tabel. Du skal bruge produktoplysningerne ved henvendelser til
vores lokale afdeling eller vores serviceværksted.
Produktoplysninger
Mejselhammer TE 300A36
Generation 03
Serienummer
1.5 Overensstemmelseserklæring
Vi erklærer som eneansvarlige, at det beskrevne produkt er i overensstemmelse med gældende direktiver og
standarder. Sidst i dette dokument finder du et bilede af overensstemmelseserklæringen.
Den tekniske dokumentation er arkiveret her:
Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE
2 Sikkerhed
2.1 Generelle sikkerhedsanvisninger for elværktøj
ADVARSEL Læs alle sikkerhedsanvisninger, henvisninger, billedtekster og tekniske data på
elværktøjet. Hvis følgende anvisninger ikke overholdes, er der risiko for elektrisk stød, brand og/eller
alvorlige personskader.
*2201963* 2201963 Dansk 13
Opbevar alle sikkerhedsanvisninger og instruktioner til senere brug.
Det benyttede begreb "elværktøj" i sikkerhedsanvisningerne refererer til elektriske maskiner (med netledning)
eller batteridrevne maskiner (uden netledning).
Arbejdspladssikkerhed
Sørg for at holde arbejdsområdet ryddeligt og godt oplyst. Uorden eller uoplyste arbejdsområder
øger faren for uheld.
Brug ikke elværktøj i eksplosionstruede omgivelser, hvor der er brændbare væsker, gasser eller
støv. Elværktøj kan slå gnister, der kan antænde støv eller dampe.
Sørg for, at andre personer og ikke mindst børn holdes væk fra arbejdsområdet, når elværktøjet
er i brug. Hvis man distraheres, kan man miste kontrollen over maskinen.
Elektrisk sikkerhed
Elværktøjets stik skal passe til kontakten. Stikket må under ingen omstændigheder ændres. Brug
ikke adapterstik sammen med jordforbundne elværktøj. Uændrede stik, der passer til kontakterne,
nedsætter risikoen for elektrisk stød.
Undgå kropskontakt med jordforbundne overflader som f.eks. rør, radiatorer, komfurer og
køleskabe. Hvis din krop er jordforbundet, øges risikoen for elektrisk stød.
Elværktøj må ikke udsættes for regn eller fugt. Indtrængning af vand i elværktøj øger risikoen for
elektrisk stød.
Brug ikke ledningen til formål, den ikke er beregnet til (f.eks. må man aldrig bære elværktøjet i
ledningen, hænge det op i ledningen eller rykke i ledningen for at trække stikket ud af kontakten).
Beskyt ledningen mod varme, olie, skarpe kanter eller dele, der er i bevægelse. Beskadigede eller
sammenviklede ledninger øger risikoen for elektrisk stød.
Hvis elværktøjet benyttes i det fri, må der kun benyttes en forlængerledning, der er egnet til
udendørs brug. Brug af forlængerledning til udendørs brug nedsætter risikoen for elektrisk stød.
Hvis det ikke kan undgås at anvende elværktøjet i fugtige omgivelser, skal du anvende et
fejlstrømsrelæ. Anvendelsen af et fejlstrømsrelæ nedsætter risikoen for et elektrisk stød.
Personlig sikkerhed
Det er vigtigt at være opmærksom, se, hvad man laver, og bruge maskinen fornuftigt. Anvend aldrig
elværktøj, hvis du er træt eller påvirket af stoffer, alkohol eller medicin. Et øjebliks uopmærksomhed
under brugen af elværktøjet kan medføre alvorlige personskader.
Brug beskyttelsesudstyr, og hav altid beskyttelsesbriller på. Brug af sikkerhedsudstyr som f.eks.
støvmaske, skridsikkert fodtøj, beskyttelseshjelm eller høreværn afhængigt af elværktøjets type og
anvendelse nedsætter risikoen for personskader.
Undgå utilsigtet igangsætning. Kontrollér, at elværktøjet er frakoblet, før du slutter det til
strømforsyningen og/eller batteriet, tager det op eller transporterer det. Undgå at bære elværktøjet
med fingeren på afbryderen, og sørg for, at det ikke er tændt, når det sluttes til nettet, da dette øger
risikoen for personskader.
Fjern indstillingsværktøj eller skruenøgler, inden elværktøjet tændes. Hvis et stykke værktøj eller en
nøgle sidder i en roterende maskindel, er der risiko for personskader.
Undgå at arbejde i unormale kropsstillinger. Sørg for at stå sikkert, mens der arbejdes, og kom
ikke ud af balance. Det er derved nemmere at kontrollere elværktøjet, hvis der skulle opstå uventede
situationer.
Brug egnet arbejdstøj. Undgå løse beklædningsgenstande eller smykker. Hold hår, tøj og handsker
væk fra dele, der bevæger sig. Dele, der er i bevægelse, kan gribe fat i løstsiddende tøj, smykker eller
langt hår.
Hvis støvudsugnings- og opsamlingsudstyr kan monteres, er det vigtigt, at dette tilsluttes og
benyttes korrekt. Ved at anvende en støvudsugning er det muligt at nedsætte risiciene som følge af
støv.
Man må ikke ignorere sikkerhedsreglerne for elværktøj, heller ikke selvom man er fortrolig med
brugen af elværktøjet. Uagtsomhed kan medføre alvorlig tilskadekomst inden for få sekunder.
Anvendelse og pleje af elværktøjet
Undgå at overbelaste maskinen. Brug altid en maskine, der er beregnet til det stykke arbejde,
der skal udføres. Med det rigtige værktøj arbejder man bedst og mest sikkert inden for det angivne
effektområde.
Brug ikke elværktøj, hvis afbryderen er defekt. En maskine, der ikke kan startes og stoppes, er farlig
og skal repareres.
Træk stikket ud af stikkontakten, og/eller fjern batteriet fra maskinen, inden du foretager
indstillinger på den, skifter tilbehør og dele eller lægger den til side. Disse sikkerhedsforanstaltninger
forhindrer utilsigtet start af elværktøjet.
14 Dansk 2201963 *2201963*
Opbevar ubenyttede elværktøjer uden for børns rækkevidde. Lad aldrig personer, der ikke er
fortrolige med maskinen eller ikke har gennemlæst sikkerhedsanvisningerne, benytte denne.
Elværktøj er farligt, hvis det benyttes af ukyndige personer.
Sørg for at pleje elværktøj omhyggeligt. Kontrollér, om bevægelige dele fungerer korrekt og
ikke sidder fast, og om delene er brækket eller beskadiget, således at elværktøjets funktion
påvirkes. Få beskadigede dele repareret, inden elværktøjet tages i brug. Mange uheld skyldes
dårligt vedligeholdte elværktøjer.
Sørg for, at skæreværktøjer er skarpe og rene. Omhyggeligt vedligeholdte skæreværktøjer med
skarpe skærekanter sætter sig ikke så hurtigt fast og er nemmere at føre.
Anvend elværktøj, tilbehør, indsatsværktøj osv. i overensstemmelse med disse anvisninger. Tag
hensyn til arbejdsforholdene og det arbejde, der skal udføres. I tilfælde af anvendelse af maskinen til
formål, som ligger uden for det fastsatte anvendelsesområde, kan der opstå farlige situationer.
Sørg for, at greb og gribeflader er tørre, rene og fri for olie og fedt. Glatte greb og gribeflader gør
betjeningen usikker, og det kan være svært at styre elværktøjet i uforudsete situationer.
Anvendelse og pleje af batteridrevet elværktøj
Oplad kun batterier i ladere, der er anbefalet af fabrikanten. Der er risiko for brand, hvis en lader, der
er beregnet til et bestemt batteri, anvendes til opladning af en anden batteritype.
Brug kun de batterier, der er beregnet til elværktøjet. Brug af andre batterier øger risikoen for
personskader og er forbundet med brandfare.
Ikke benyttede batterier må ikke komme i berøring med kontorclips, mønter, nøgler, søm, skruer
eller andre små metalgenstande, da disse kan kortslutte kontakterne. En kortslutning mellem
batterikontakterne øger risikoen for personskader i form af forbrændinger.
Hvis batteriet anvendes forkert, kan der løbe væske ud af batteriet. Undgå at komme i kontakt
med denne væske. Hvis det alligevel skulle ske, skylles med vand. Søg læge, hvis væsken kommer
i øjnene. Batterivæske kan give hudirritation eller forbrændinger.
Brug aldrig et beskadiget eller ændret batteri. Beskadigede eller ændrede batterier kan virke utilsigtet
og medføre brand, eksplosion eller risiko for tilskadekomst.
Batterier må ikke udsættes for åben ild eller høje temperaturer. Ild eller temperaturer over 130 °C
(265 °F) kan medføre eksplosion.
Følg alle anvisninger vedrørende opladning, og oplad aldrig batteriet eller det batteridrevne
værktøj uden for det temperaturområde, der er anført i betjeningsvejledningen. Forkert opladning
eller opladning uden for det tilladte temperaturområde kan ødelægge batteriet og øge risikoen for brand.
Service
Sørg for, at elværktøjet kun repareres af kvalificerede fagfolk, og at der altid benyttes originale
reservedele. Dermed sikres størst mulig elværktøjssikkerhed.
Forsøg aldrig at reparere beskadigede batterier. Al vedligeholdelse af batterier skal foretages af
producenten eller af autoriserede forhandlere.
2.2 Sikkerhedsanvisninger til hamre
Brug høreværn. Støjpåvirkningen kan medføre høretab.
Brug de ekstrahåndgreb, som følger med maskinen. Hvis du mister kontrollen, kan det medføre
personskader.
Hold maskinen på de isolerede grebsflader, når du udfører opgaver, hvor indsatsværktøjet kan
ramme skjulte strømledninger. Ved kontakt med en spændingsførende ledning kan også metalliske
værktøjsdele sættes under spænding, hvilket kan medføre elektrisk stød.
2.3 Yderligere sikkerhedsanvisninger, mejselhammer
Personlig sikkerhed
Anvend kun produktet og tilbehør i teknisk fejlfri stand.
Foretag aldrig manipulationer eller ændringer på produkt eller tilbehør.
Ved mejsling af lofter, vægge og gulve er det vigtigt at stå sikkert og stabilt. Hvis værktøjet pludselig går
igennem, kan du miste balancen!
Ved gennembrydningsarbejde skal du huske at sikre området på den modsatte side. Nedbrydningsdele
kan falde ud og/eller ned og volde skade på andre personer.
Sørg for, at du selv og personer, som opholder sig i nærheden under brugen af maskinen, anvender
egnede beskyttelsesbriller, sikkerhedshjelm, høreværn og et let åndedrætsværn.
Brug beskyttelseshandsker, når du skifter værktøj. Berøring af indsatsværktøjet kan medføre snitsår og
forbrændinger.
*2201963* 2201963 Dansk 15
Brug øjenværn. Splinterne fra materialet kan medføre skader på legeme og øjne.
Støv, der dannes ved slibning, skæring og boring, kan indeholde farlige kemikalier. Nogle eksempler er:
Bly eller maling på blybasis; Tegl, beton og andre murværksprodukter, natursten og andre silikatholdige
produkter; Bestemte træsorter som eg, bøg og kemisk behandlet træ; Asbest eller asbestholdige
materialer. Bestem eksponeringen for brugeren og omkringstående personer ved hjælp af fareklassen
for de materialer, der arbejdes på. Træf de nødvendige foranstaltninger for at holde eksponeringen på et
sikkert niveau, f.eks. ved at bruge et støvopsamlingssystem eller brug af et passende åndedrætsværn.
Generelle foranstaltninger til at reducere eksponeringen omfatter bl.a.:
Arbejde i et godt ventileret område,
Undgå længere tids kontakt med støv,
Lede støv bort fra ansigt og krop,
Bruge beskyttende beklædning og vaske eksponerede områder med vand og sæbe.
Hold hyppigt pauser, og lav øvelser, så fingrene får bedre blodgennemstrømning. Ved længerevarende
arbejde kan vibrationer medføre forstyrrelser af fingrenes, hændernes eller håndleddenes blodkar og
nervesystem.
Elektrisk sikkerhed
Kontrollér før påbegyndelse af arbejdet arbejdsområdet for skjulte elektriske ledninger, gas- og vandrør,
f.eks. med en metaldetektor. Udvendige metaldele på produktet kan medføre elektrisk stød eller
forårsage en eksplosion, hvis r du beskadiger en elledning, et gasrør eller et vandrør.
Omhyggelig omgang med og brug af elværktøj
Vent, indtil produktet er standset helt, før du lægger det fra dig.
2.4 Omhyggelig omgang med og brug af batterier
Læs de særlige retningslinjer for transport, opbevaring og brug af lithiumion-batterier.
Hold batterier på sikker afstand af høje temperaturer, direkte solindstråling og ild.
Batterierne må ikke adskilles, klemmes, opvarmes til over 80 °C eller brændes.
Anvend og oplad ikke batterier, som har fået et slag, er faldet på gulvet fra mere end en meters højde
eller på anden vis er blevet beskadiget. Kontakt i så fald altid Hilti Service.
Hvis batteriet er for varmt til at kunne røres, kan det være defekt. Anbring batteriet på et overskueligt,
ikke-brændbart sted med tilstrækkelig afstand til brændbare materialer. Lad batteriet køle af. Hvis
batteriet efter en time fortsat er for varmt til at kunne røres, er det er defekt. Kontakt Hilti Service.
3 Beskrivelse
3.1 Produktoversigt 1
@Værktøjsholder
;Funktionsvælger
=Afbryder
%Ladetilstands- og fejlvisning, batteri
&Frigøringsknapper / Aktivering, ladetilstands-
visning
(Batteri
3.2 Bestemmelsesmæssig anvendelse
Det beskrevne produkt er en batteridrevet mejselhammer med pneumatisk slagmekanisme. Produktet er
beregnet til lette og moderate mejselopgaver i murværk og til efterbearbejdning af beton.
Anvend kun Hilti lithium-ion-batterier i typeserien B 36 til dette produkt.
Anvend kun Hilti ladere i C4/36-serien til disse batterier.
16 Dansk 2201963 *2201963*
3.3 Potentiel forkert brug
Dette produkt egner sig ikke til bearbejdning af sundhedsskadelige materialer.
Dette produkt egner sig ikke til arbejde i fugtige miljøer.
Brug ikke produktet, hvis der er risiko for brand eller eksplosion.
3.4 Indikator for lithium-ion-batteriet
Lithium-ion-batteriets ladetilstand og fejl på maskinen signaleres via lithium-ion-batteriets indikator. Lithium-
ion-batteriets ladetilstand vises efter berøring af de to batterifrigøringsknapper.
Tilstand Betydning
4 lysdioder lyser. Ladetilstand: 75 % til 100 %
3 lysdioder lyser. Ladetilstand: 50 % til 75 %
2 lysdioder lyser. Ladetilstand: 25 % til 50 %
1 lysdiode lyser. Ladetilstand: 10 % til 25 %
1 lysdiode blinker. Ladetilstand: < 10 %
1 lysdiode blinker, maskinen er ikke klar til brug. Batteriet er overophedet eller helt afladet.
4 lysdioder blinker, maskinen er ikke klar til brug. Maskinen er overbelastet eller overophedet.
Når afbryderen er aktiveret, og op til 5 sekunder efter at afbryderen er sluppet, er det ikke muligt at få
vist ladetilstanden.
Hvis lysdioderne på batteriets indikator blinker, henvises til beskrivelsen i kapitlet Fejlafhjælpning.
3.5 Leveringsomfang
Mejselhammer, sidegreb, brugsanvisning.
Andre systemprodukter, som er godkendt til dit produkt, finder du i dit Hilti Store eller online på adressen:
www.hilti.group | USA: www.hilti.com.
4 Tekniske data
4.1 Produktdata
TE 300A36
Nominel spænding 36 V
Vægt målt med B36⁄5.2 i overensstemmelse med EPTA-procedure 01 4,9 kg
4.2 Støjinformation og vibrationsværdier iht. EN 60745
Lydtryk- og vibrationsværdier i denne brugsanvisning er målt i henhold til en standardiseret målemetode
og kan anvendes til sammenligning af forskellige elværktøjer. De kan også anvendes til en foreløbig
vurdering af den eksponering, brugeren udsættes for. De anførte data repræsenterer elværktøjets primære
anvendelsesformål. Hvis elværktøjet imidlertid anvendes til andre formål, med andre indsatsværktøjer
eller utilstrækkelig vedligeholdelse, kan dataene afvige. Dette kan forøge den eksponering, som brugeren
udsættes for, i hele arbejdstiden markant. For at opnå en præcis vurdering af den eksponering, som brugeren
udsættes for, bør også den tid, hvor maskinen er slukket eller blot kører uden at blive anvendt, inddrages.
Dette kan reducere den eksponering, som brugeren udsættes for, i hele arbejdstiden markant. Fastlæg
yderligere sikkerhedsforanstaltninger til beskyttelse af brugeren mod støj- og/eller vibrationspåvirkninger,
f.eks. er det vigtigt at vedligeholde elværktøj og indsatsværktøj, at holde hænderne varme og at organisere
arbejdsprocesserne.
Støjinformation
TE 300A36
Lydeffektniveau (LWA)99 dB
Usikkerhed (KWA)3 dB(A)
Lydtrykniveau (L, pA)88 dB
Usikkerhed (KpA)3 dB(A)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152

Hilti TE 300­-A36 SDS Plus Breaker ユーザーマニュアル

カテゴリー
パワードリル
タイプ
ユーザーマニュアル