Blackmagic 2110 IP Converter 3x3G ユーザーマニュアル

Blackmagic 2110 IP Converter 3x3G

October 2023

Installation and Operation Manual

Blackmagic

2110 IP

Converter 3x3G

Languages

To go directly to your preferred language, simply click on the hyperlinks listed in the

contents below.

English 3

日本語 26

Français 50

Deutsch 74

Español 98

中文 122

한국어 146

Русский 170

Italiano 194

Português 218

Türkçe 242

Polski 266

Українська 290

Welcome

Thank you for purchasing your Blackmagic 2110 IP Converter 3x3G!

Your bidirectional IP converter lets you simultaneously convert SDI to IP and IP to SDI via

3 independent 3G-SDI inputs and outputs and a fast 10G Ethernet connection.

All 3G-SDI inputs feature loop outputs so you can install the converter in line within existing

SDI systems. Loop outputs plus converted outputs means you can feed up to 6 separate

HD channels to 6 separate SDI devices! The reference output is timed to the 2110 PTP

clock so you can sync all connected signals and the elegant front panel features control

buttons and a color LCD for monitoring, menus and diagnostics. You can even route IP

inputs from the panel!

This instruction manual should contain all the information you’ll need for installing your

Blackmagic 2110 IP Converter 3x3G and getting started.

Please check the support page on our web site at www.blackmagicdesign.com for the

latest version of the Blackmagic Converters software. When downloading software, please

register with your information so we can keep you updated when new software is released.

We are constantly working on new features and improvements, so we would love to

hear from you!

Grant Petty

CEO Blackmagic Design

English

Contents

Getting Started 5

Plugging in Power 5

Plugging in SDI Sources 5

Plugging in Ethernet 6

Subscribing to a Stream 6

Setting up a Network 7

Connecting to a Network Switch 7

PTP Grandmaster 8

NMOS Controller 8

Using The Front Panel 9

Home Screen 9

Using the LCD Menu 10

Settings 11

Outputs Menu 11

Audio Menu 12

Setup Menu 12

Rear Panel 15

Blackmagic Converters Setup 16

Inputs 16

Outputs 17

Setup 17

Blackmagic Universal Rack Shelf 20

Contents 20

Mounting a Unit to the Rack Shelf 21

Attaching the 1/6 Blanking Panel 21

Attaching the Side 1/3 Width

Blanking Panel 21

Help 22

Regulatory Notices 23

Safety Information 24

Warranty 25

4Blackmagic 2110 IP Converter 3x3G

Getting Started

Getting started with Blackmagic 2110 IP Converter 3x3G is as simple as connecting power,

adding your SDI sources and then connecting the two converters directly using a Cat 6

Ethernet cable.

SDI SDI

Ethernet

INPUT DISP H/V

DELAY

3D

LUT 1

BLUE

ONLY ZOOM PEAK 3D

LUT 2

H

MARK

V

MARK

The illustration shows a point to point connection with a HyperDeck connected to the first IP

converter’s SDI input that sends the video to the second IP converter via Ethernet. The second

converter can then output the video to SDI equipment such as a SmartView monitor or an

ATEM switcher.

Plugging in Power

To power your Blackmagic 2110 IP Converter 3x3G, plug a standard IEC cable to the power

input on the rear of the converter. Once powered, the LCD will prompt you to select your

language. Using the menu dial, scroll to the language you wish to use and press the flashing

‘set’ button. This will take you to the home screen.

Plugging in SDI Sources

Connect the HD source to the first 3G-SDI input on the first unit. Your source could be a camera

or HyperDeck or any other 3G-SDI HD equipment. Once connected, the input will appear on

the front panel LCD.

5Getting Started

Using the second Blackmagic 2110 IP Converter 3x3G connect an SDI monitor or other SDI

equipment to the first SDI output on the rear of the unit.

Plugging in Ethernet

Now connect your two converters directly using a Cat 6 Ethernet cable.

The network status icon in the upper left corner of the LCD home screen will indicate ‘10G’

when a successful connection is made. This will be visible on both units.

SDI SDI

Ethernet

INPUT DISP H/V

DELAY

3D

LUT 1

BLUE

ONLY ZOOM PEAK 3D

LUT 2

H

MARK

V

MARK

Subscribing to a Stream

On the front panel of the second Blackmagic 2110 IP Converter 3x3G you can now select the

stream for your SDI output using the menu. This is known as subscribing to a stream.

To subscribe to a stream:

1 Press the ‘menu’ button to open the menu and press ‘set’ to select the ‘SDI

outputs’ submenu.

2 Rotate the menu dial to ‘SDI 1’ and press ‘set’. The streams from the first converter will

appear in a list which you can select by rotating the menu dial and pressing ‘set’.

LOCK

SET

MENU

3

2

11

3 If the output doesn’t appear on the front panel display, press the ‘1’ button twice to change

to output mode.

6Getting Started

Your Blackmagic 2110 IP converters are now connected. You can also connect Blackmagic 2110

IP Converter 3x3G to a network with other IP video equipment including DeckLink IP and NMOS

controllers. Please keep reading the next section of this manual for information on how to

connect your Blackmagic 2110 IP Converter 3x3G to a 10G network switch to share multiple HD

video feeds over a network.

Setting up a Network

If this is your first time setting up a 10G network for streaming ST 2110 IP video, there are few

considerations you should take into account when getting started. IP media is sent in packets,

so it’s important to have a PTP aware switch to provide the timing information to synchronize

the devices connected to the network. The management of the traffic flow is covered by a

separate control system named NMOS that can be added to the network via either a software

or hardware solution.

SDI IN

SDI OUT

ETHERNET

+12V

SDI IN

SDI OUT

ETHERNET

+12V

STATUS ENTER

BACK

REF

TIME

BLACK

LTC

SDI

CMPST

EMBED SYSTEM ENABLE

AES PTP

INPUTS OUTPUTS

FRONT PANEL

USB

INT EXT TIME PWR1 PWR2 FAULT

SET

SEARCH

MENU

INPUT DISP H/V

DELAY

3D

LUT 1

BLUE

ONLY ZOOM PEAK 3D

LUT 2

H

MARK

V

MARK

1 213 314 415 516 617 819 920 1021 1122 1223

G25 G26

24718

SFP

SG200-26 26-Port Gigabit Smart Switch

System

Reset

PTP Grandmaster

10G managed switch

NMOS Controller

Connecting to a Network Switch

Your network switch needs to be a managed 10G network switch that supports IGMP version

3 snooping.

Managed switches provide monitoring and control of traffic over the network and require

configuration to get started. The size of you network switch depends on how much traffic you

might need. For instance, an 8 port 10G Ethernet switch has a capacity of 160Gbps and a 16

port switch will allow up to 320Gbps.

The following 10G network switches have been tested with Blackmagic 2110 IP Converter 3x3G:

Manufacturer Model

Ubiquiti Enterprise XG-24

The switch needs to be Internet Group Management Protocol, or IGMP L3 enabled. IGMP is a

communication protocol that allows the switch to route multicast data.

With multicasting one stream can be subscribed to by multiple outputs while only using the

bandwidth of one single stream.

7Setting up a Network

INPUT DISP H/V

DELAY

3D

LUT 1

BLUE

ONLY ZOOM PEAK 3D

LUT 2

H

MARK

V

MARK

INPUT DISP H/V

DELAY

3D

LUT 1

BLUE

ONLY ZOOM PEAK 3D

LUT 2

H

MARK

V

MARK INPUT DISP H/V

DELAY

3D

LUT 1

BLUE

ONLY ZOOM PEAK 3D

LUT 2

H

MARK

V

MARK INPUT DISP H/V

DELAY

3D

LUT 1

BLUE

ONLY ZOOM PEAK 3D

LUT 2

H

MARK

V

MARK

INPUT DISP H/V

DELAY

3D

LUT 1

BLUE

ONLY ZOOM PEAK 3D

LUT 2

H

MARK

V

MARK INPUT DISP H/V

DELAY

3D

LUT 1

BLUE

ONLY ZOOM PEAK 3D

LUT 2

H

MARK

V

MARK

In the diagram above one ST 2110 stream has been subscribed to by 6 outputs but the bandwidth required by

the network switch bandwidth is for one stream only.

PTP Grandmaster

In order to maintain timing you need a Precision Time Protocol grandmaster or PTP clock

connected to the switch. Similar to using genlock via a master sync generator for synced SDI

connections, PTP generates accurate timing and frequency to maintain the packets of ST 2110

data over the network. This ensures that all streams are synchronized.

The PTP clock is the grandmaster and all other IP video devices should be set as the ‘follower’

to ensure no timing conflicts can occur. For more information on setting your Blackmagic 2110 IP

Converter 3x3G as a follower, refer to the ‘setup menu’ later in this manual.

NMOS Controller

Traditional SDI connections send signals in one direction with video, audio and ancillary data

such as timecode and closed captions embedded in the one signal.

With ST 2110, the signal is split into video, audio and ancillary data elementary streams. This

provides flexibility to route video, audio or ancillary data streams independently whilst keeping

each essence stream synchronized so they can be brought back together at the end of

the workflow.

This is all achieved through timing. But how does one converter know what the other converter

is doing? This is where the Networked Media Open Specifications, or NMOS for short, is

important.

NMOS is a group of specifications that direct the flow of traffic in an IP network and manage

communications between all the endpoint devices. Once a hardware or software NMOS

controller is connected to the network you can route any or all of the elementary streams to any

endpoint device on the network.

8Setting up a Network

Using The Front Panel

When using Blackmagic 2110 IP Converter 3x3G any information you need to know is displayed

on the unit itself via the LCD home screen and the buttons and menu dial let you quickly

change settings. This section of the manual describes each feature on the front panel and what

it is used for.

LOCK

SET

MENU

3

2

1

2

3

4

1 USB-C

USB-C port for updates and configuring via Blackmagic Converters Setup utility.

2 Input and Output Buttons

The numbered buttons on the front panel let you select quickly between inputs and

outputs. To switch between input and output mode, double press any of the numbered

buttons. To see which mode you are in, check the icon on the home screen. The button will

illuminate when selected.

3 Menu Buttons

Use the menu and set buttons along with the menu dial to configure settings. The buttons

can also be locked by holding down the lock button until the button label illuminates red. To

unlock the buttons simply hold the lock button down again. More information on using the

LCD menu follows.

4 LCD

The LCD shows the home preview screen with status icons and LCD menu.

Home Screen

Icons displayed above the video preview indicate the current status of the Blackmagic 2110 IP

Converter 3x3G. Below is a description of the information displayed.

9Using The Front Panel

Network Status

Connected via 10G Ethernet point to point or via a network switch

Network not connected

Video Standard

Blackmagic 2110 IP Converter 3x3G supports the following video standards:

SD Video 525i59.94 NTSC, 625i50 PAL

HD Video 720p50, 720p59.94, 720p60

1080i50, 1080i59.94, 1080i60

1080p23.98, 1080p24, 1080p25, 1080p29.97, 1080p30,

1080p50, 1080p59, 1080p59.94, 1080p60

Input or Output Indicator

Displays the current input or output. Switch between input and output mode by double pressing

any of the numbered buttons. The numbered button will also illuminate when selected. Input

and output labels can be edited using the Converters Setup utility.

SDI input

SDI output

Audio Meters

Displays the audio levels of the selected input or output. Meter type can be selected via the

audio menu with options including VU -18dBFS, VU -20dBFS, PPM -18dBFS or PPM -20dBFS

reference levels.

Using the LCD Menu

Press the ‘menu’ button on the front panel to open the menu settings.

LOCK

SET

MENU

3

2

1

10Using The Front Panel

Turn the menu dial to navigate between the menu options and press ‘set’ to select a submenu.

LOCK

SET

MENU

3

2

1

Turn the menu dial to move through the menu settings

Using the menu dial, select the submenu option and press ‘set’ to confirm.

LOCK

SET

MENU

3

2

11

Press ‘menu’ to step back through the options and return to the home screen.

Settings

Outputs Menu

Use the output menu to route incoming ST 2110 sources to the SDI outputs on the rear of the

Blackmagic 2110 IP Converter 3x3G.

You can also route your sources and destinations using an NMOS controller. This will provide

flexibility to subscribe to the video, audio or ancillary essences.

To route an ST 2110 stream to the SDI output on your Blackmagic 2110 IP Converter 3x3G:

1 With the ‘outputs’ menu selected press the ‘set’ button.

2 Use the menu dial to select which SDI output you want to use and press the ‘set’ button.

11Settings

3 Available ST 2110 streams will appear in the list. Rotate the menu dial to select which stream

you want and press ‘set’.

4 Press the menu button repeatedly to return to the preview screen.

5 Now from the home screen make sure the same output is selected via the

numbered buttons.

To stop an incoming stream, select ‘none’ from the list.

Audio Menu

The built in LCD shows audio meters for embedded audio channels. You can select to display

PPM or VU Meters. To change your meter type, expand the menu setting and select your

preferred audio meter display from the options from VU -18dBFS, VU -20dBFS, PPM -18dBFS or

PPM -20dBFS reference levels.

Setup Menu

The setup menu contains settings including language selection, date and time options, network

settings and multicasting output settings.

Name

When more than one Blackmagic 2110 IP Converter 3x3G is on the network, you may wish to

give them discrete names. This can be done via Blackmagic Converters Setup.

12Settings

Language

Blackmagic 2110 IP Converter 3x3G supports 13 languages, including English, Chinese,

Japanese, Korean, Spanish, German, French, Russian, Italian, Portuguese, Turkish, Ukrainian

and Polish.

To select the language:

1 Press the ‘menu’ button and rotate the menu dial to the setup menu and press ‘set’

to select.

2 Rotate the menu dial to highlight your preferred language and press ‘set’.

3 Once selected, you will automatically return to the setup menu.

Software

Displays the current software version.

Front Panel

Set your Blackmagic converter’s front panel to ‘light’ mode for a brightly illuminated LCD. Use

‘dark’ mode for dimly lit environments where a bright LCD may be distracting, for example

multiple converter units mounted in a rack in a production facility.

Date and Time

Setting the date and time correctly ensures your Blackmagic 2110 IP Converter 3x3G has the

same time and date information as your network and also prevents conflicts that can occur with

some network systems.

Auto Set Date and Time

To set your date and time automatically select set the auto set date and time option to ‘on’..

When setting the date and time automatically, the converter will use the network time protocol

server set in the NTP field. To override the date and time manually, select ‘off’.

13Settings

NTP

The default NTP server is time.cloudflare.com, but you can also manually enter an alternate NTP

server using Blackmagic Converters Setup. For more information on setting the NTP server,

refer to Blackmagic Converters Setup later in this manual.

Date

To enter the date manually, select the date field and press set. Using the menu dial you can

select the day, month and year.

Time

To adjust the time, select time and press set. Use the menu dial to adjust the hours and minutes.

The internal clock is a 24 hour clock.

Network Settings

Protocol

Your Blackmagic 2110 IP Converter 3x3G is shipped set to static IP, so once connected, you can

assign an IP address. To change to DHCP, highlight the protocol option and press ‘set’.

IP Address, Subnet Mask and Gateway

When Static IP is selected you need to enter your network details manually.

To change the IP address

1 Rotate the menu dial to highlight ‘IP address’ and press the flashing ‘set’ button on your

converter’s front panel.

2 With a set of numbers underlined, press the ‘set’ button to highlight and rotate the menu

dial clockwise to increase or counter clockwise to decrease.

3 Press ‘set’ to confirm the change and move to the next value.

When you have finished entering your IP address, you can repeat these steps to adjust the

subnet mask and gateway. Once finished, press the flashing ‘menu’ button to exit and return to

the home screen.

2110 Multicast Output

Each streaming output is assigned a different multicast output address.

14Settings

This setting is similar to an IP address and lets other SMPTE 2110 IP equipment identify the

stream on your network. Each stream from your converter requires its own multicast output

address. NMOS controllers will also display the audio and ancillary data multicast addresses

associated with each source.

Reference Output

The dedicated reference out BNC connection on the rear lets you set the timing for other

devices connected to your Blackmagic 2110 IP Converter 3x3G. You can set your output

standard to SD or HD using the list selection.

Factory Reset

Highlight ‘factory reset’ in the setup menu to restore your Blackmagic 2110 IP Converter 3x3G to

factory settings. Once you press ‘set’, you will be prompted to confirm your selection.

Rear Panel

1

4 5

2 3

6

1 Power

IEC C14 connector for 90 – 240 volt AC power supply.

2 SDI Out

3G-SDI video output BNC connectors.

3 SDI Loop Out

3G-SDI video loop output BNC connectors.

4 10G Ethernet PoE+

Blackmagic 2110 IP Converter 3x3G can be connected point to point or via a managed 10G

IGMP network switch.

15Rear Panel

5 Ref Out

Your Blackmagic 2110 IP Converter 3x3G features a stabilized video reference output

corresponding to standard definition black burst and high definition tri-sync standards. For

more information on selecting your reference output, refer to the ‘settings’ section earlier in

this manual.

6 SDI In

3G-SDI video input BNC connectors.

Blackmagic Converters Setup

Blackmagic Converters Setup is a software utility used to change settings and update the

internal software in your IP converter.

First, download and install the latest Blackmagic Converters software from the Blackmagic Design

support center at www.blackmagicdesign.com/support

To use Blackmagic Converters Setup:

1 Connect your Blackmagic converter to your computer via USB.

2 Launch Converters Setup. Your converter model will be named in the utility home page.

3 Click on the circular ‘setup’ icon or the image of your Blackmagic 2110 IP Converter 3x3G to

open the settings.

Inputs

Use the inputs tab to label the connected SDI inputs. The NMOS protocol broadcasts these

labels to make identifying them via an NMOS controller or other Blackmagic 2110 IP Converter

3x3G easy.

16Blackmagic Converters Setup

Outputs

Use the outputs tab to label the SDI outputs. For example, if SDI output 2 is connected to a

HyperDeck Studio HD Plus, enter ‘HyperDeck HD Plus’ in the output 2 field. If you are using an

NMOS controller to route your sources and destinations, you can select ‘HyperDeck HD Plus’

from the destination selection tab.

Labels

You can also save or load label sets using the cog icon in the lower left corner of the utility.

To save a label set, click on the save option and navigate to a location to save the file.

To load a label set, click on the load option and navigate to the location of your label set. Once

selected, click open.

Setup

Setup settings let you change the name of your converter, change network settings, displays

the current version of your converter’s internal software and view multicast output addresses.

Identiﬁcation Settings

Use the identification settings to enter the name and language for your converter.

17Blackmagic Converters Setup

Entering a custom name is helpful to identify the right Blackmagic 2110 IP Converter 3x3G when

more than one is connected to your network. It also provides the name for network location.

You can also identify the current software version.

Date and Time

Set your date and time automatically by ticking the box. When setting the date and time

automatically, your converter will use the network time protocol server set in the NTP field. The

default NTP server is time.cloudflare.com, but you can also manually enter an alternate NTP

server and then click on ‘set’.

If you are entering your date and time manually, use the fields to enter your date, time and time

zone. Setting the date and time correctly ensures your recordings have the same time and

date information as your network and also prevents conflicts that can occur with some network

storage systems.

Network Settings

Network Location

The network location is the name for your Blackmagic 2110 IP Converter 3x3G that will appear

in the registry. This is based on the identification name at the top of the setup utility. It’s worth

noting that numeric prefixes will be ignored.

Protocol

DHCP and static IP settings let you determine how your converter is connected to your network.

DHCP Blackmagic 2110 IP converters are set to DHCP by default. The dynamic host

configuration protocol, or DHCP, is a service on network servers that automatically

finds your converter and assigns an IP address. DHCP is a great service that makes

it easy to connect equipment via Ethernet and ensure their IP addresses do not

conflict with each other. Most computers and network switchers support DHCP.

Static IP When ‘static IP’ is selected, you can enter your network details manually. When

setting IP addresses manually so all units can communicate, they must share the

same subnet mask and gateway settings.

When using static IP and there are other devices on the network that have the same identifying

number in their IP address there will be a conflict and the units won’t connect. If you encounter

a conflict, simply change the identifying number in the unit’s IP address.

18Blackmagic Converters Setup

For example, if the conflicting address is 192.100.40.30 change the last number field to anything

other than 30. If the new number is also being used, keep changing it until you find a unique

number that isn’t being used by other equipment.

Allow utility administration

Enabling the ‘via USB’ setting limits setting changes to only the computer connected via USB.

This removes the risk of anyone on the network making accidental settings changes.

2110 Multicast Output

Each ST 2110 stream output from your Blackmagic 2110 IP Converter 3x3G uses its own

multicast output address. These can be found via the setup utility or by using the LCD menu.

Precision Time Protocol

When connecting Blackmagic 2110 IP Converter 3x3G to a 10G network switch with a PTP

grandmaster, the converter needs to be set to follower mode to prevent a timing conflict.

If two Blackmagic IP converters are connected directly, set one to be the follower by ticking the

checkbox.

Reference Output

To change the reference output for the ref out BNC connector on the rear of the converter,

select the reference from the menu.

Reset

Click ‘factory reset’ to restore your Blackmagic 2110 IP Converter 3x3G to factory settings. Once

you press ‘set’, you will be prompted to confirm your selection. To proceed, click ‘reset’.

Installing into a Blackmagic Universal Rack Shelf

Your Blackmagic 2110 IP Converter 3x3G shares a compatible form factor with many other

Blackmagic Design units that can be mounted in a rack. The next section of this manual shows

how to install the converter into the Blackmagic Universal Rack Shelf.

19Blackmagic Converters Setup

Blackmagic Universal Rack Shelf

Blackmagic Universal Rack Shelf is a 1RU shelf that lets you install a broad range of

Blackmagic Design equipment into a broadcast rack or road case. The modular design means

you can build portable and practical equipment setups using products that share a single rack

unit form factor.

The illustration below shows 3 Universal Rack Shelves installed in a small rack with a

combination of compatible units mounted. The bottom shelf includes a 1/3 rack width blanking

panel to fill unused space between units.

Contents

The Universal Rack Shelf Kit contains the following items.

1 x Blackmagic Universal Rack Shelf

A single rack unit, full width shelf for installing

Blackmagic Design equipment.

Blanking Panels

1 x 1/6 rack width and 2 x 1/3 rack width blanking

panels to cover unused shelf space.

Screws

12 x M3 5mm

countersunk mounting

screws.

2 x M3 9mm flat screws

for 1/6 blanking panels.

20Blackmagic Universal Rack Shelf

ページを読み込んでいます...

Blackmagic 2110 IP Converter 3x3G ユーザーマニュアル

関連論文

その他の書類