DCD771
DCD776
2
English (original instructions) 3
中文 (简体） 14
Copyright DeWALT
1
Figure 1
a
b
c
d
f
e
g
h
Figure 2
h
g
k
DCD771
i
j
2
Figure 3
Figure 7
c
Figure 4 Figure 5
Figure 8 Figure 9
f
i
Figure 6
c
DCD776
ENGLISH
3
CORDLESS COMPACT 13 mm (1/2") DRILL/DRIVER/
HAMMERDRILL
DCD771, DCD776
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make
DeWALT one of the most reliable partners for professional power tool users.
Technical Data
DCD771 DCD776
Voltage V
DC
18(20 Max) 18(20 Max)
Battery Type Li-Ion Li-Ion
Power output W 300 300
No-load speed
1st gear min
-1
0–450 0–450
2nd gear min
-1
0–1500 0–1500
Impact rate
1st gear min
-1
– 0–7650
2nd gear min
-1
– 0–25 500
Max. torque (hard/soft) Nm 42/24 42/24
Chuck capacity mm 13 13
Maximum drilling capacity
Wood mm 25 25
Metal mm 13 13
Masonry mm – 13
Weight (without battery pack) kg 1.3 1.34
Batteries Chargers / Charge Times (Minutes)
Cat# V
DC
Ah Weight(kg)
DCB104 DCB107 DCB112 DCB113 DCB115 DCB118 DCB132 DCB119
DCB546/DCB606 18/54 (20/60 Max) 6.0/2.0 1.05 60 270 170 140 90 60 90 X
DCB547/DCB609 18/54 (20/60 Max) 9.0/3.0 1.46 75* 420 270 220 135* 75* 135* X
DCB548/DCB612 18/54 (20/60 Max) 12.0/4.0 1.44 120 540 350 300 180 120 180 X
DCB181 18 (20 Max) 1.5 0.35 22 70 45 35 22 22 22 45
DCB182/DCB204 18 (20 Max) 4.0 0.61 60/40** 185 120 100 60 60/40** 60 120
DCB183/DCB203 18 (20 Max) 2.0 0.40 30 90 60 50 30 30 30 60
DCB184/DCB205 18 (20 Max) 5.0 0.62 75/50** 240 150 120 75 75/50** 75 150
DCB185 18 (20 Max) 1.3 0.35 22 60 40 30 22 22 22 X
DCB187 18 (20 Max) 3.0 0.54 45 140 90 70 45 45 45 90
DCB189 18 (20 Max) 4.0 0.54 60 185 120 100 60 60 60 120
*
Date code 201811475B or later
**
Date code 201536 or later
ENGLISH
4
Definitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of fire.
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result
in electric shock, fire and/or serious
injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
ENGLISH
5
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any other
condition that may affect the power tool’s
operation. If damaged, have the power
tool repaired before use. Many accidents
are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with another
battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery, avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by
a qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
Additional Specific Safety Rules for
Drill/Driver/Hammerdrill
• Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
• Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
• Hold power tool by insulated gripping
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring. Cutting accessory contacting a
“live” wire may make exposed metal parts of the
power tool “live” and could give the operator an
electric shock.
• Use clamps or other practical way to secure
and support the workpiece to a stable
platform. Holding the work by hand or against
your body is unstable and may lead to loss of
control.
• Wear safety goggles or other eye protection.
Hammering and drilling operations cause chips
to fly. Flying particles can cause permanent eye
damage.
ENGLISH
6
• Accessories and tool may get hot during
operation. Wear gloves when handling them if
performing heat producing applications such as
hammerdrilling and drilling metals.
• Do not operate this tool for long periods of
time. Vibration caused by hammer action may
be harmful to your hands and arms. Use gloves
to provide extra cushion and limit exposure by
taking frequent rest periods.
• Air vents often cover moving parts and
should be avoided. Loose clothes, jewelry or
long hair can be caught in moving parts.
Residual Risks
The following risks are inherent to the use of drills:
– Injuries caused by touching the rotating parts or
hot parts of the tool.
In spite of the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
– Impairment of hearing.
– Risk of squeezing fingers when changing
accessories.
– Health hazards caused by breathing dust
developed when working in wood.
– Risk of personal injury due to flying particles.
– Risk of personal injury due to prolonged use.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
DATE CODE POSITION (FIG. 1)
The Date Code (j), which also includes the year of
manufacture, is printed into the housing surface that
forms the mounting joint between tool and battery.
Example:
2020 XX XX
Year of Manufacture
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual
contains important safety and operating instruc tions
for the DCB107 battery chargers.
• Before using the charger, read all instructions
and cautionary markings on charger, battery
pack and product using the battery pack.
WARNING: Shock hazard. Do not allow
any liquid to get inside charger. Electric
shock may result.
CAUTION: Burn hazard. To reduce
the risk of injury, charge only DeWALT
rechargeable battery packs. Other types
of batteries may overheat and burst
resulting in personal injury and property
damage.
CAUTION: Children should be
supervised to ensure that they do not
play with the appliance.
NOTICE: Under certain conditions, with
the charger plugged in to the power
supply, the exposed charging contacts
inside the charger can be shorted by
foreign material. Foreign materials of
a conductive nature such as, but not
limited to, steel wool, aluminum foil or
any buildup of metallic particles should
be kept away from charger cavities.
Always unplug the charger from the
power supply when there is no battery
pack in the cavity. Unplug charger
before attempting to clean.
• DO NOT attempt to charge the battery pack
with any chargers other than the ones in
this manual. The charger and battery pack are
specifically designed to work together.
• These chargers are not intended for
any uses other than charging DeWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock or
electrocution.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when
disconnecting charger. This will reduce risk
of damage to electric plug and cord.
• Make sure that cord is located so that it
will not be stepped on, tripped over or
otherwise subjected to damage or stress.
• Do not use an extension cord unless it
is absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock or electrocution.
• When operating a charger outdoors, always
provide a dry location and use an extension
cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of
electric shock.
ENGLISH
7
• Do not block the ventilation slots on the
charger. The ventilation slots are located
on the top and sides of the charger. Place
the charger in a position away from any heat
source.
• Do not operate charger with damaged cord
or plug — have them replaced immediately.
• Do not operate charger if it has received
a sharp blow, been dropped or otherwise
damaged in any way. Take it to an authorised
service centre.
• Do not disassemble the charger; take
it to an authorised service centre when
service or repair is required. Incorrect
reassembly may result in a risk of electric shock,
electrocution or fire.
• In case of damaged power supply cord the
supply cord must be replaced immediately by
the manufacturer, its service agent or similar
qualified person to prevent any hazard.
• Disconnect the charger from the outlet
before attempting any cleaning. This will
reduce the risk of electric shock. Removing
the battery pack will not reduce this risk.
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on
standard 220-240 V household electrical
power. Do not attempt to use it on any other
voltage. This does not apply to the vehicular
charger.
SAVE THESE INSTRUCTIONS
Chargers
The DCB107 charger accepts 10.8V(12V
Max),18V(20V Max) Li-Ion (DCB121, DCB123,
DCB140, DCB141, DCB142, DCB180, DCB181,
DCB182, DCB183, DCB185,DCB187,DCB189,DCB
203,DCB204 and DCB205) battery packs.
This charger requires no adjustment and is designed
to be as easy as possible to operate.
Charging Procedure (fig. 2)
1. Plug the charger into an appropriate 220-240V
outlet before inserting the battery pack.
2. Insert the battery pack (g) into the charger,
making sure the pack is fully seated in the
charger. The red (charging) light will blink
continuously indicating that the charging
process has started.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
NOTE: To ensure maximum performance and life of
Li-Ion batteries, charge the battery pack fully before
first use.
Charging Process
Refer to the table below for the state of charge of
the battery pack.
State of charge–DCB107
charging –– –– –– –– ––
fully charged ––––––––––––––––––––
hot/cold pack delay –– –– –– –––––––
HOT/COLD PACK DELAY (DCB107)
The DCB107 charger has a hot/cold delay feature.
When the charger detects a battery that is hot, it
automatically delays charging until the battery has
cooled.
When the charger detects a battery that is cold, it
automatically delays charging until the battery has
warmed.
The red light will continue to blink, but a yellow
indicator light will be illuminated during this
operation. Once the battery has cooled, the yellow
light will turn off and the charger will resume the
charging procedure.
XR Li-Ion tools are designed with an Electronic
Protection System that will protect the battery
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
Li-Ion battery on the charger until it is fully charged.
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure
to include the catalog number and voltage.
The battery pack is not fully charged out of the
carton. Before using the battery pack and charger,
read the safety instructions below and then follow
the charging procedures outlined.
READ ALL INSTRUCTIONS
• Do not charge or use the battery pack
in explosive atmospheres, such as in the
presence of flammable liquids, gases or
dust. Inserting or removing the battery pack
from the charger may ignite the dust or fumes.
ENGLISH
8
• Never force the battery pack into charger.
Do not modify the battery pack in any way
to fit into a non-compatible charger as
battery pack may rupture causing serious
personal injury.
• Charge the battery packs only in designated
DeWALT chargers.
• DO NOT splash or immerse in water or other
liquids.
• Do not store or use the tool and battery
pack in locations where the temperature
may reach or exceed 40˚C (105˚F) (such
as outside sheds or metal buildings in
summer).
• For best results, make sure the battery pack is
fully charged before use.
WARNING: Never attempt to open
the battery pack for any reason. If
the battery pack case is cracked or
damaged, do not insert it into the
charger. Do not crush, drop or damage
battery pack. Do not use a battery
pack or charger that has received a
sharp blow, been dropped, run over
or damaged in any way (e.g., pierced
with a nail, hit with a hammer, stepped
on). Electric shock or electrocution may
result. Damaged battery packs should
be returned to the service centre for
recycling.
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large
battery packs will stand upright on the
battery pack but may be easily knocked
over.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION
(Li-Ion)
• Do not incinerate the battery pack even if it
is severely damaged or is completely worn
out. The battery pack can explode in a fire.
Toxic fumes and materials are created when
lithium ion battery packs are burned.
• If battery contents come into contact with
the skin, immediately wash the area with
mild soap and water. If the battery liquid gets
into the eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte
is composed of a mixture of liquid organic
carbonates and lithium salts.
• Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If
symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid
may be flammable if exposed to spark
or flame.
Battery Pack
BATTERY TYPE
The DCD771 and DCD776 operate on 18 volt
battery packs.
The DCB180, DCB181, DCB182, DCB183 or
DCB185 battery packs may be used. Refer to
Technical Data for more information.
Storage Recommendations
1. The best storage place is one that is cool and
dry away from direct sunlight and excess heat
or cold. For optimum battery performance and
life, store battery packs at room temperature
when not in use.
2. For long storage, it is recommended to store a
fully charged battery pack in a cool, dry place
out of the charger for optimal results.
NOTE: Battery packs should not be stored
completely depleted of charge. The battery pack will
need to be recharged before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual,
the labels on the charger and the battery pack show
the following pictographs:
Read instruction manual before use.
Charging.
Fully charged.
Hot/cold pack delay.
x
Problem pack or charger.
Problem powerline.
Do not probe with conductive objects.
Do not charge damaged battery packs.
ENGLISH
9
Use only with DeWALT battery packs.
Others may burst, causing personal injury
and damage.
Do not expose to water.
Have defective cords replaced
immediately.
Charge only between 4˚C and 40˚C.
Discard the battery pack with due care for
the environment.
Do not incinerate the battery pack.
Li-ION
Charges Li-Ion battery packs.
See Technical Data for charging time.
Only for indoor use.
Package Contents
The package contains:
1 Drill/driver or 1 drill/driver/hammerdrill
1 Charger
1 Li-Ion battery pack (C1 model)
2 Li-Ion battery packs (C2 model)
3 Li-Ion battery packs (C3 model)
1 Kitbox
1 Instruction manual
NOTE: Battery packs, chargers and kitboxes are
not included with N-models.
• Check for damage to the tool, parts or
accessories which may have occurred during
transport.
• Take the time to thoroughly read and
understand this manual prior to operation.
Description (fig. 1)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
a. Trigger switch
b. Forward/reverse control button
c. Torque adjustment collar
d. Gear shifter
e. Worklight
f. Keyless chuck
g. Battery pack
h. Battery release button
i. Main handle
INTENDED USE
These drills/drivers/hammerdrills are designed
for professional drilling, percussion drilling and
screwdriving applications.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
These drills/drivers/hammerdrills are professional
power tools.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
• This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the battery pack
voltage corresponds to the voltage on the rating
plate. Also make sure that the voltage of your
charger corresponds to that of your mains.
Your DeWALT charger is double insulated
in accordance with IEC 60335; therefore
no earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DeWALT service organisation.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see Technical Data). The minimum conductor size
is 1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ENGLISH
10
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
WARNING: Use only DeWALT battery
packs and chargers.
Inserting and Removing the
Battery Pack from the Tool (fig. 2)
WARNING: Prior to assembly and
adjustment, always remove the
battery pack. Always switch off the
tool before inserting or removing
the battery pack.
NOTE: For best results, make sure your battery
pack is fully charged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the battery pack (g) with the rails inside the
tool’s handle (fig. 2).
2. Slide it into the handle until the battery pack is
firmly seated in the tool and ensure that it does
not disengage.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the battery release button (h) and firmly
pull the battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
FUEL GAUGE BATTERY PACKS (FIG. 2)
Some D
eWALT battery packs include a fuel gauge
which consists of three green LED lights that
indicate the level of charge remaining in the battery
pack.
To actuate the fuel gauge, press and hold the fuel
gauge button (k). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
Variable Speed Trigger Switch
(fig.1)
To turn the tool on, squeeze the trigger switch (a).
To turn the tool off, release the trigger switch. Your
tool is equipped with a brake. The chuck will stop as
soon as the trigger switch is fully released.
NOTE: Continuous use in variable speed range is
not recommended. It may damage the switch and
should be avoided.
Forward/Reverse Control Button
(fig. 1)
A forward/reverse control button (b) determines the
direction of the tool and also serves as a lock-off
button.
To select forward rotation, release the trigger switch
and depress the forward/reverse control button on
the right side of the tool.
To select reverse, depress the forward/reverse
control button on the left side of the tool.
The center position of the control button locks
the tool in the off position. When changing the
position of the control button, be sure the trigger is
released.
NOTE: The first time the tool is run after changing
the direction of rotation, you may hear a click on
start up. This is normal and does not indicate a
problem.
Torque Adjustment Collar (fig. 1)
Your tool has an adjustable torque screwdriver
mechanism for driving and removing a wide array of
fastener shapes and sizes and in some models, a
hammer mechanism for drilling into masonry. Circling
the collar (c) are numbers, a drill bit symbol, and on
some models, a hammer symbol. These numbers
are used to set the clutch to deliver a torque range.
The higher the number on the collar, the higher the
torque and the larger the fastener which can be
driven. To select any of the numbers, rotate until the
desired number aligns with the arrow.
Dual Range Gearing (fig. 1)
The dual range feature of your drill/driver/hammerdrill
allows you to shift gears for greater versatility.
1. To select speed 1 (high torque setting), turn
the tool off and permit it to stop. Slide the gear
shifter (d) forward (towards the chuck).
2. To select speed 2 (low torque setting), turn the
tool off and permit it to stop. Slide the gear
shifter back (away from the chuck).
ENGLISH
11
NOTE: Do not change gears when the tool is
running. Always allow the drill to come to a complete
stop before changing gears. If you are having trouble
changing gears, make sure that the dual range
gear shifter is either completely pushed forward or
completely pushed back.
Worklight (fig. 1)
There is a worklight (e) located just above the
trigger switch (a). The worklight is activated when
the trigger switch is depressed. When the trigger is
released, the worklight will stay illuminated for up to
20 seconds.
NOTE: The worklight is for lighting the immediate
work surface and is not intended to be used as a
flashlight.
Keyless Single Sleeve Chuck
(fig. 7–9)
WARNING: Do not attempt to tighten
drill bits (or any other accessory) by
gripping the front part of the chuck
and turning the tool on. Damage to
the chuck and personal injury may
result. Always lock off trigger switch
and disconnect tool from power source
when changing acces sories.
WARNING: Always ensure the bit
is secure before starting the tool. A
loose bit may eject from tool causing
possible personal injury.
Your tool features a keyless chuck (f) with one
rotating sleeve for one-handed operation of the
chuck. To insert a drill bit or other accessory, follow
these steps.
1. Turn tool off and disconnect tool from power
source.
2. Grasp the black sleeve of the chuck with one
hand and use the other hand to secure the
tool. Rotate the sleeve counterclockwise far
enough to accept the desired accessory.
3. Insert the accessory about 19 mm (3/4") into
the chuck and tighten securely by rotating
the chuck sleeve clockwise with one hand
while holding the tool with the other. Your tool
is equipped with an automatic spindle lock
mechanism. This allows you to open and close
the chuck with one hand.
Be sure to tighten chuck with one hand on the
chuck sleeve and one hand holding the tool for
maximum tightness.
To release the accessory, repeat steps 1 and 2
above.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
Proper Hand Position (fig. 3)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the top
of the drill as shown, with the other hand on the
main handle (i).
Screwdriver Operation (fig. 4)
1. Select the desired speed/torque range using the
dual range gear selector to match the speed
and torque of the planned operation.
2. Turn the torque adjustment collar (c) to the
desired position. Lower numbers indicate lower
torque settings; higher numbers indicate higher
torque settings.
3. Insert the desired fastener accessory into the
chuck as you would any drill bit.
4. Make some practice runs in scrap or on unseen
areas to determine the proper position of the
clutch collar.
5. Always start with lower torque settings, then
advance to higher torque settings to avoid
damage to the workpiece or fastener.
Drill Operation (fig. 5)
WARNING: To reduce the risk of
serious personal injury, turn tool off and
disconnect tool from power source
before making any adjustments or
removing/installing attachments or
accessories.
ENGLISH
12
WARNING: To reduce the risk of
personal injury, ALWAYS ensure
workpiece is anchored or clamped
firmly. If drilling thin material, use a wood
“back-up” block to prevent damage to
the material.
1. Turn the collar (c) to the drill symbol.
2. Select the desired speed/torque range using the
gear shifter to match the speed and torque to
the planned operation.
3. For WOOD, use twist bits, spade bits, power
auger bits or hole saws. For METAL, use high-
speed steel twist drill bits or hole saws. Use
a cutting lubricant when drilling metals. The
exceptions are cast iron and brass which should
be drilled dry.
4. Always apply pressure in a straight line with the
bit. Use enough pressure to keep drill biting, but
do not push hard enough to stall the motor or
deflect the bit.
5. Hold tool firmly with both hands to control
the twisting action of the drill. If model is not
equipped with side handle, grip drill with one
hand on the handle and one hand on the
battery pack.
CAUTION: Drill may stall if overloaded
causing a sudden twist. Always expect
the stall. Grip the drill firmly to control
the twisting action and avoid injury.
6. IF DRILL STALLS, it is usually because
it is being overloaded or improperly used.
RELEASE TRIGGER IMMEDIATELY, remove
drill bit from work, and determine cause of
stalling. DO NOT CLICK TRIGGER ON
AND OFF IN AN ATTEMPT TO START A
STALLED DRILL — THIS CAN DAMAGE
THE DRILL.
7. To minimize stalling or breaking through the
material, reduce pressure on drill and ease the
bit through the last fractional part of the hole.
8. Keep the motor running when pulling the bit
back out of a drilled hole. This will help prevent
jamming.
9. With variable speed drills there is no need to
center punch the point to be drilled. Use a
slow speed to start the hole and accelerate by
squeezing the trigger harder when the hole is
deep enough to drill without the bit skipping
out.
Hammerdrill Operation (fig. 6)
DCD776
1. Turn the collar (c) to the hammerdrill symbol.
2. Select the high speed setting by sliding the
selector back (away from the chuck).
IMPORTANT: Use carbide-tipped or masonry
bits only.
3. Drill with just enough force on the hammer to
keep it from bouncing excessively or “rising” off
the bit. Too much force will cause slower drilling
speeds, overheating and lower drilling rate.
4. Drill straight, keeping the bit at a right angle to
the work. Do not exert side pressure on the bit
when drillling as this will cause clogging of the
bit flutes and a slower drilling speed.
5. When drilling deep holes, if the hammer speed
starts to drop off, pull the bit partially out of the
hole with tool stil running to help clear debris
from the hole.
NOTE: A smooth, even flow of dust from the hole
indicates proper drilling rate.
MAINTENANCE
Your DeWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
The charger and battery pack are not serviceable.
There are no serviceable parts inside.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
ENGLISH
13
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
Optional Accessories
WARNING: Since accessories, other
than those offered by D
eWA LT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only D
eWALT recommended
accessories should be used with this
product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your D
eWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products
and packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
D
eWALT provides a facility for the collection and
recycling of D
eWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
D
eWALT office at the address indicated in this
manual. Alternatively, a list of authorised D
eWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when
it fails to produce sufficient power on jobs which
were easily done before. At the end of its technical
life, discard it with due care for our environment:
• Run the battery pack down completely, then
remove it from the tool.
• Li-Ion cells are recyclable. Take them to your
dealer or a local recycling station. The collected
battery packs will be recycled or disposed of
properly.
简体中文
14
13 毫米（1/2 英寸）锂电充电式电钻起子/冲击钻
DCD771、DCD776
恭喜！
感谢您选购 DeWALT 工具。凭借多年的产品开发和创新经验，DeWALT 已经成为专业电动工具用户最可靠的
合作伙伴之一。
技术参数
DCD771 DCD776
电压 伏特 18(20Max) 18(20Max)
电池类型 锂离子 锂离子
空载转速
1档 转/分 0-450 0–450
2档 转/分
0-1500 0–1500
冲击率
1档 转/分 – 0–7650
2档 转/分 – 0–25500
最大扭矩（硬/软） 牛米 42/24 42/24
夹头尺寸 毫米 13 13
最大钻孔能力
木材 毫米 25 25
金属 毫米 13 13
砖石 毫米 – 13
重量（不含电池组） 千克 1.3 1.34
电池 充电器/充电时间（分钟）
目录号 伏特
直流
安时
重量
（千克）
DCB104 DCB107 DCB112 DCB113 DCB115 DCB118 DCB132 DCB119
DCB546/DCB606 18/54 (
最大20/60) 6.0/2.0 1.05 60 270 170 140 90 60 90 X
DCB547/DCB609 18/54 (
最大20/60) 9.0/3.0 1.46 75* 420 270 220 135* 75* 135* X
DCB548/DCB612 18/54 (
最大20/60) 12.0/4.0 1.44 120 540 350 300 180 120 180 X
DCB181 18 (
最大20) 1.5 0.35 22 70 45 35 22 22 22 45
DCB182/DCB204 18 (
最大20) 4.0 0.61 60/40** 185 120 100 60 60/40** 60 120
DCB183/DCB203 18 (
最大20) 2.0 0.40 30 90 60 50 30 30 30 60
DCB184/DCB205 18 (
最大20) 5.0 0.62 75/50** 240 150 120 75 75/50** 75 150
DCB185 18 (
最大20) 1.3 0.35 22 60 40 30 22 22 22 X
DCB187 18 (
最大20) 3.0 0.54 45 140 90 70 45 45 45 90
DCB189 18 (
最大20) 4.0 0.54 60 185 120 100 60 60 60 120
简体中文
15
定义：安全指引
下列定义描述了各警示词的严重程度。请仔细阅读
本手册，并注意这些警示符号。
危险：表示存在紧急危险情况，
如果不加以避免，将导致死亡或严重伤
害。
警告：表示存在潜在的危险情况，如果不
加以避免，可能导致死亡或严重伤害。
警示：表示存在潜在危险情况，如果不加
以避免，可能导致轻度或中度伤害。
注意：表示存在不涉及人身伤害的情况，
如果不加以避免，可能导致财产损失。
表示存在触电风险。
表示存在火灾风险。
警告： 为降低伤害风险，请阅读使用手
册。
电动工具通用安全警告
警告！阅读所有警告和所有说明。不遵照
以下警告和说明会导致电击、着火和／
或严重伤害。
保存所有警告和说明书以备查阅。
在所有下列的警告中术语“电动工具”指市电驱动
（有线）电动工具或电池驱动（无线）电动工具。
a) 工作场地的安全
1)
保持工作场地清洁和明亮。
混乱和黑暗的场
地会引发事故。
2) 不要在易爆环境，如有易燃液体、气体或粉尘
的环境下操作电动工具。电动工具产生的火
花会点燃粉尘或气体。
3) 让儿童和旁观者离开后操作电动工具。注意
力不集中会使你失去对工具的控制。
b) 电气安全
1) 电动工具插头必须与插座相配。绝不能以任
何方式改装插头。需接地的电动工具不能使
用任何转换插头。未经改装的插头和相配的
插座将减少电击危险。
2) 避免人体接触接地表面，如管道、散热片和冰
箱。如果你身体接地会增加电击危险。
3) 不得将电动工具暴露在雨中或潮湿环境中。
水进入电动工具将增加电击危险。
4) 不得滥用电线。绝不能用电线搬运、拉动电动
工具或拔出其插头。使电线远离热源、油、锐
边或运动部件。受损或缠绕的软线会增加电
击危险。
5) 当在户外使用电动工具时，使用适合户外使
用的外接软线。适合户外使用的软线将减少
电击危险。
6) 如果在潮湿环境下操作电动工具是不可避免
的，应使用剩余电流动作保护器（RCD）。使用
RCD可减小电击危险。
c) 人身安全
1) 保持警觉，当操作电动工具时关注所从事的
操作并保持清醒。当你感到疲倦，或在有药
物、酒精或治疗反应时，不要操作电动工具。
在操作电动工具时瞬间的疏忽会导致严重人
身伤害。
2) 使用个人防护装置。始终佩戴护目镜。安全装
置，诸如适当条件下使用防尘面具、防滑安全
鞋、安全帽、听力防护等装置能减少人身伤
害。
3) 防止意外起动。确保开关在连接电源和/或电
池组、拿起或搬运工具时处于关断位置。手指
放在已接通电源的开关上或开关处于接通时
插入插头可能会导致危险。
4) 在电动工具接通之前，拿掉所有调节钥匙或
扳手。遗留在电动工具旋转零件上的扳手或
钥匙会导致人身伤害。
5) 手不要伸展得太长。时刻注意立足点和身体
平衡。这样在意外情况下能很好地控制电动
工具。
简体中文
16
6) 着装适当。不要穿宽松衣服或佩戴饰品。让你
的衣服、手套和头发远离运动部件。宽松衣
服、佩饰或长发可能会卷入运动部件中。
7) 如果提供了与排屑、集尘设备连接用的装置，
要确保他们连接完好且使用得当。使用这些
装置可减少尘屑引起的危险。
d) 电动工具使用和注意事项
1) 不要滥用电动工具，根据用途使用适当的电
动工具。选用适当设计的电动工具会使你工
作更有效、更安全。
2) 如果开关不能接通或关断工具电源，则不能
使用该电动工具。不能用开关来控制的电动
工具是危险的且必须进行修理。
3) 在进行任何调节、更换附件或贮存电动工具
之前，必须从电源上拔掉插头和／或使电池
组与工具脱开。这种防护性措施将减少工具
意外起动的危险。
4) 将闲置不用的电动工具贮存在儿童所及范围
之外，并且不要让不熟悉电动工具或对这些
说明不了解的人操作电动工具。电动工具在
未经培训的用户手中是危险的。
5) 保养电动工具。检查运动件是否调整到位或
卡住，检查零件破损情况和影响电动工具运
行的其他状况。如有损坏，电动工具应在使用
前修理好。许多事故由维护不良的电动工具
引发。
6) 保持切削刀具锋利和清洁。保养良好的有锋
利切削刃的刀具不易卡住而且容易控制。
7) 按照使用说明书，考虑作业条件和进行的作
业来使用电动工具、附件和工具的刀头等。将
电动工具用于那些与其用途不符的操作可能
会导致危险。
e) 电池式工具使用和注意事项：
1) 只用制造商规定的充电器充电。将适用于某
种电池组的充电器用到其他电池组时会发生
着火危险。
2) 只有在配有专用电池组的情况下才使用电动
工具。 使用其他电池组会发生损坏和着火危
险。
3) 当电池组不用时，将它远离其他金属物体，例
如回形针、硬币、钥匙、钉子、螺钉或其他小金
属物体，以防一端与另一端连接。电池端部短
路会引起燃烧或火灾。
4) 在滥用条件下，液体会从电池中溅出，避免接
触。如果意外碰到了，用水冲洗。如果液体碰
到了眼睛，还要寻求医疗帮助。从电池中溅出
的液体会发生腐蚀或燃烧。
f) 维修
1) 让专业维修人员使用相同的备件维修电动工
具。这将保证所维修的电动工具的安全。
电钻起子/冲击钻的附加安全细则
• 使用冲击钻时要戴好耳罩。暴露在噪声中会引
起听力损伤。
• 使用随工具提供的辅助手柄。操作失手会引起
人身伤害。
• 当在钻削附件可能触及暗线或其自身软线之处
进行操作时，要通过绝缘握持面来握持工具。钻
削附件碰到带电导线会使工具外露的金属零件
带电从而使操作者受到电击。
• 使用夹具或采取其它可行的方法，将工件固定、
支撑到稳定的平台上。手持或用身体顶住工件
都是不稳定的，会导致操作失控。
• 请佩戴安全护目镜或其他护目装备。冲击或钻
孔会导致碎片飞散。飞散的颗粒会对眼睛造成永
久性伤害。
• 附件和工具可能会在使用过程中发热。如果进
行放热应用（如冲击钻孔和金属钻孔），处理时请
佩戴手套。
• 不要长时间操作此工具。锤击操作导致的振动
可能会伤害您的手部和手臂。使用手套提供额外
缓冲，经常停下休息，限制使用时间。
• 通风口通常会盖住运动部件，应加以避免。宽松
衣服、佩饰或长发可能会卷入运动部件。
简体中文
17
剩余风险
使用电钻时具有下列风险：
– 碰触工具的旋转部件或带热的部件会导致人身
伤害。
尽管遵守了相关的安全法规并采用了安全装备，某
些剩余风险仍然是无法避免的。这些风险包括：
– 听力损伤。
– 更换附件时扭伤手指的风险。
– 锯切木材时，吸入粉尘导致的健康危害。
– 飞溅颗粒造成的人身伤害风险。
– 长时间使用引起的人身伤害风险。
工具上的标记
工具上印有下列标志：
使用前请阅读使用手册。
日期码位置（图 1）
连接工具和电池之间的机壳表面印有日期代码 ( j)，
日期代码包括制造年份。
示例：
2020 XX XX
制造年份
针对所有电池充电器的重要安全
说明
请妥善保管好这些说明： 本手册包含重要的
DCB107 电池充电器安全和操作说明。
• 使用充电器之前，请阅读所有说明和充电器、电
池组以及电池组产品上的警示标记。
警告：触电危险。请勿让任何液体渗入充
电器，否则会引起触电。
警示：灼伤危险。为了减少受伤的危险，
只使用 DeWALT 充电式电池组充电。其
他类型的电池可能会过热爆裂，并造成
人身伤害和财产损失。
警示：必须监督儿童，确保他们不将此设
备当做玩具来玩。
注意：在某些情况下，充电器连接电源
时，异物可能会连接充电器内的外露充
电接触点而造成短路。请勿让能导电的
异物靠近充电器腔，这些异物包括但不
限于钢棉、铝箔或任何金属颗粒的堆积
物。充电器内没有电池组时，请断开充电
器与电源的连接。清洗前，务必拔掉充电
器。
• 请勿试图使用本手册指定的充电器以外的其他
任何充电器为电池组充电。充电器和电池组都
是专门设计的，互相配合使用。
• 除了为 DeWALT 充电式电池充电以外，这些充
电器都不能用于其他任何用途。否则，可能会导
致火灾、触电或电击。
• 请勿将充电器暴露于雨中或雪中。
• 断开充电器时应拔下插头，切勿拉拽电线。这将
减少电源插头和电源线损坏的风险。
• 确保电源线布置在不易踩踏、踢绊、拉扯或会受
到损坏或压力的位置。
• 非绝对必要条件下禁止使用延长线。使用延长
线不当可能会导致火灾、触电或电击的危险。
• 户外操作充电器时，请务必提供一个干燥的地
方，并使用适合户外使用的延长电线。采用适合
户外使用的电线可降低触电风险。
• 禁止堵塞充电器上的通风槽。通风槽位于充电
器的顶部和两侧。请把充电器放置在远离任何热
源的地方。
• 禁止使用电源线或插头已损坏的充电器 - 请立
即更换已损坏的充电器。
• 如果充电器受到强烈重击、掉落或出现其他损
坏情况，请不要使用充电器。请将损坏的充电器
送到授权维修中心维修。
• 请勿拆卸充电器，请将需要维修或修理的充电
器送到授权维修中心。重装不正确可能会导致
触电、电击或火灾风险。
简体中文
18
• 必须立即将已损坏的电源线交由制造商、服务代
理或类似的合格人员进行更换以防止安全隐患。
• 清洁前，请先断开充电器和插座的连接，以降低
触电风险。取出电池组不会降低触电风险。
• 切勿试图将两个充电器连接在一起。
• 充电器额定电压是标准 220 伏家用电压。请勿
试图在任何其他电压下使用充电器。此规则不
适用于车载充电器。
请妥善保管好这些说明
充电器
DCB107 充电器适用于 10.8伏（最大12伏） 伏、18伏
（最大20伏） 伏锂离子（DCB121、DCB123、DCB140
、DCB141、
DCB142、DCB180、DCB181、DCB182、DCB183 和
DCB185）电池组。
此充电器专为简易操作而设计，因此无需做出任何
调 整 。
充电程序（图 2）
1. 插入电池组前请将充电器插入到相应的 220-
240 伏插 座 。
2. 将电池组 (g) 插入到充电器中，确定电池组完全
就位。红色（充电中）指示灯将不断闪烁，表示充
电过程已经开始。
3. 红色灯持续亮起表示充电完成。此时电池组已完
全充电，您可以使用电池组或将电池组留在充电
器上。
注：为了确保锂离子电池的效能和使用寿命最大化，
在首次使用电池组之前必须将其完全充电。
充电过程
关于电池组的充电状态，请参阅下表。
充电状态-DCB107
充电中 –– –– –– –– ––
已完全充电 ––––––––––––––––––––
热/冷电池组延迟–– –– –––––––––
热/冷电池组延迟 (DCB107)
DCB107 充电器具有热/冷延迟功能。当充电器检测
到电池为热的时，它会自动延迟充电，直到电池冷却
下来为止。
当充电器检测到电池为冷的时，它会自动延迟充电，
直到电池稍变热为止。
红色指示灯会继续闪烁，但黄色指示灯在本次操作
过程中会亮起。电池冷却后，黄色指示灯会熄灭，充
电器将恢复充电程序。
XR 锂离子电池工具具有“电子保护系统”设计，可保
护电池免受过载、过热或过度放电之害。
如果电子保护系统处于运作状态，该工具将自动停
止操作。如果发生这种情况，请将锂离子电池放在充
电器上直到完全充电。
针对所有电池组的重要安全说明
在订购更换电池组时，请务必附上目录号码和电压。
包装箱内的电池组并未完全充电。在使用电池组和
充电器之前，请阅读下面的安全说明，然后按照所述
充电程序进行操作。
请阅读所有说明
• 请勿在易爆环境中充电或使用电池组，如有易
燃液体、气体或粉尘的环境。在充电器中插入或
取出电池组时可能会点燃粉尘或烟雾。
• 切勿将电池组强行插入充电器。不得以任何方
式改装电池组并将电池组插入不兼容的充电
器，这种操作可能会导致电池组破裂，并造成严
重的人身伤害。
• 只使用指定的
DeWALT 充电器为电池组充电。
• 请勿喷溅电池组或将其浸泡在水或其他液体中。
• 禁止在温度可能达到或超过 40 ºC（105 ºF）的
地方（如夏天户外的棚子或金属建筑物中）存储
或使用工具和电池组。
• 为达到最佳效果，请确保电池组在使用前已完
全充电。
警告：切勿以任何理由试图打开电池组。
电池组外壳破裂或损坏时，不要将电池
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
他の言語で
- English: DeWalt DCD776 User manual
関連論文
その他のドキュメント
-
Hilti SF 10W-A22 ATC Cordless Drill Driver ユーザーマニュアル
-
BLACK+DECKER BCD704 ユーザーマニュアル
-
Triton T12AD Operating And Safety Instructions Manual
-
Stanley STDC411L ユーザーマニュアル
-
-
-
BLACK+DECKER BDCHD12S1 ユーザーマニュアル
-
-
BLACK+DECKER KTC12 ユーザーマニュアル
-