DeWalt DCD800P2T ユーザーマニュアル

DCD800

DCD805

English (original instructions) 3

简体中文 14

繁體中文 23

한국어 31

Bahasa Indonesia 41

 53

Fig. A

图 A

圖 A

그림 A

Gam. A

346 7

12 9

XXXX XX XX

11 14

Fig. B

图 B

圖 B

그림 B

Gam. B





Fig. C

图 C

圖 C

그림 C

Gam. C

Fig. D

图 D

圖 D

그림 D

Gam. D

Fig. E

图 E

圖 E

그림 E

Gam. E







ENGLISH

DCD800-B1/A9/TW/KR DCD805-B1/A9/TW/KR DCD805-JP

Voltage VDC 18(20 Max) 18(20 Max) 18

Battery type Li-Ion Li-Ion Li-Ion

No-load speed

1st gear min-1 0–650 0–650 0–650

2nd gear min-1 0–2000 0–2000 0–2000

Impact rate

1st gear min-1 —0–11050 0–11050

2nd gear min-1 —0–34000 0–34000

Max. torque (hard/soft) Nm 90/27 90/27 90/27

Chuck capacity mm 1.5–13.0 1.5–13.0 1.5–13.0

Maximum drilling capacity

Wood mm 55 55 55

Metal mm 13 13 13

Masonry mm —13 13

Weight (without battery pack) kg 1.28 1.34 1.34

Congratulations!

You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make DeWALT one of the

most reliable partners for professional power toolusers.

Technical Data

DRILL

DCD800

DRILL/HAMMERDRILL

DCD805

English (original instructions)

Batteries Chargers / Charge Times (Minutes)

Cat# VDC Ah Weight(kg) DCB104 DCB107 DCB112 DCB115 DCB117 DCB118 DCB132 DCB1112

DCB546/DCB606 18/54 (20/60 Max) 6.0/2.0 1.08 60 270 170 90 40 60 90 40

DCB547/DCB609 18/54 (20/60 Max) 9.0/3.0 1.46 75* 420 270 135* 60 75* 135* 60

DCB548/DCB612 18/54 (20/60 Max) 12.0/4.0 1.46 120 540 350 180 80 120 180 80

DCB549/DCB615 18/54 (20/60 Max) 15.0/5.0 2.12 125 730 450 230 90 125 230 90

DCB181 18 (20 Max) 1.5 0.35 22 70 45 22 22 22 22 22

DCB182/DCB204 18 (20 Max) 4.0 0.61 60/40** 185 120 60 60/40** 60/40** 60 60/40**

DCB183/DCB203 18 (20 Max) 2.0 0.40 30 90 60 30 30 30 30 30

DCB184/DCB205 18 (20 Max) 5.0 0.62 75/50** 240 150 75 75/50** 75/50** 75 75/50**

DCB185 18 (20 Max) 1.3 0.35 22 60 40 22 22 22 22 22

DCB187 18 (20 Max) 3.0 0.54 45 140 90 45 45 45 45 45

DCB189/DCB240 18 (20 Max) 4.0 0.54 60 185 120 60 60 60 60 60

DCB186 18 (20 Max) 6.0 0.95 60 270 170 90 60 60 90 60

DCBP034 18 (20 Max) 1.7 0.32 27 82 50 27 27 27 27 27

*Date code 201811475B or later

**Date code 201536 or later

ENGLISH

aWARNING: To reduce the risk of injury, read the

instructionmanual.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.

CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.

Denotes risk of electricshock.

Denotes risk offire.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions,

illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below

may result in electric shock, fire and/or seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTUREREFERENCE

The term “power tool” in the warnings refers to your

mains‑operated (corded) power tool or battery‑operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electricshock.

b ) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electricshock.

Batteries

Chargers/Charge Times (Minutes)

Cat #

Weight

*Date code 201811475B or later

**Date code 201536 or later

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personalinjury.

b ) Use personal protective equipment. Always wear eye

protection. Protective equipment such as a dust mask,

non‑skid safety shoes, hard hat or hearing protection used

for appropriate conditions will reduce personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off‑position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invitesaccidents.

d ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personalinjury.

e ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be

caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust‑relatedhazards.

h ) Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe

injury within a fraction of asecond.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must berepaired.

ENGLISH

c ) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the

power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

h ) Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpectedsituations.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may create

a risk of injury andfire.

c ) When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation orburns.

e ) Do not use a battery pack or tool that is damaged or

modified. Damaged or modified batteries may exhibit

unpredictable behaviour resulting in fire, explosion or risk

ofinjury.

f ) Do not expose a battery pack or tool to fire or

excessive temperature. Exposure to fire or temperature

above 130°C may causeexplosion.

g ) Follow all charging instructions and do not charge

the battery pack or tool outside the temperature

range specified in the instructions. Charging

improperly or at temperatures outside the specified range

may damage the battery and increase the risk offire.

6) Service

a ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

b ) Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized serviceproviders.

Additional Specific Safety Rules for Drills/

Drivers/Impact Drills

• Wear ear protectors when impact drilling. Exposure to

noise can cause hearingloss.

• Use the auxiliary handles, if supplied with the tool. Loss

of control can cause personalinjury.

• Brace the tool properly before use. This tool produces a

high output torque and without properly bracing the tool

during operation, loss of control may occur resulting in

personalinjury.

• Hold the power tool by insulated gripping surfaces when

performing an operation where the cutting accessory or

fasteners may contact hidden wiring. Cutting accessory

or fasteners contacting a “live” wire may make exposed metal

parts of the power tool “live” and could give the operator an

electricshock.

Safety Instructions When Using Long

DrillBits

• Never operate at higher speed than the maximum

speed rating of the drill bit. At higher speeds, the bit is likely

to bend if allowed to rotate freely without contacting the

workpiece, resulting in personalinjury.

• Always start drilling at low speed and with the bit tip

in contact with the workpiece. At higher speeds, the bit is

likely to bend if allowed to rotate freely without contacting the

workpiece, resulting in personalinjury.

• Apply pressure only in direct line with the bit and do not

apply excessive pressure. Bits can bend causing breakage or

loss of control, resulting in personalinjury.

• Use clamps or other practical way to secure and support

the workpiece to a stable platform. Holding the work by

hand or against your body is unstable and may lead to loss

ofcontrol.

• Wear ear protectors when hammering for extended

periods of time. Prolonged exposure to high intensity noise

can cause hearing loss. Temporary hearing loss or serious ear

drum damage may result from high sound levels generated

byhammerdrilling.

• Wear safety goggles or other eye protection. Hammering

and drilling operations cause chips to fly. Flying particles can

cause permanent eyedamage.

• Hammer bits and tools get hot during operation. Wear

gloves when touchingthem.

ENGLISH

• Do not operate this tool for long periods of time.

Vibration caused by hammer action may be harmful to your

hands and arms. Use gloves to provide extra cushion and limit

exposure by taking frequent restperiods.

• Air vents often cover moving parts and should be

avoided. Loose clothes, jewellery or long hair can be caught

in movingparts.

Residual Risks

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment ofhearing.

• Risk of personal injury due to flyingparticles.

• Risk of burns due to accessories becoming hot

duringoperation.

• Risk of personal injury due to prolongeduse.

SAVE THESE INSTRUCTIONS

Chargers

DeWALT chargers require no adjustment and are designed to be

as easy as possible tooperate.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of yourmains.

iYour DeWALTcharger is double insulated in

accordance with IEC60335; therefore no earth wire

isrequired.

If the supply cord is damaged, it must be replaced only by

DeWALT or an authorised serviceorganisation.

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1mm2; the maximum length

is30m.

When using a cable reel, always unwind the cablecompletely.

Important Safety Instructions for All

BatteryChargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for compatible battery

chargers (refer to TechnicalData).

• Before using charger, read all instructions and cautionary

markings on charger, battery pack, and product using

batterypack.

WARNING: Shock hazard. Do not allow any liquid to get

inside charger. Electric shock mayresult.

WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA orless.

CAUTION: Burn hazard. To reduce the risk of injury,

charge only DeWALT rechargeable batteries. Other types of

batteries may burst causing personal injury anddamage.

CAUTION: Children should be supervised to ensure that

they do not play with theappliance.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the exposed charging

contacts inside the charger can be shorted by foreign

material. Foreign materials of a conductive nature such

as, but not limited to, steel wool, aluminum foil or any

buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity.

Unplug charger before attempting toclean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger

and battery pack are specifically designed to worktogether.

• These chargers are not intended for any uses other than

charging DeWALT rechargeable batteries. Any other uses

may result in risk of fire, electric shock orelectrocution.

• Do not expose charger to rain orsnow.

• Pull by plug rather than cord when disconnecting

charger. This will reduce risk ofdamage to electric plug

andcord.

• Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire,electric shock, orelectrocution.

• Do not place any object on top of charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source. The

charger is ventilated through slots in the top and the bottom

of thehousing.

• Do not operate charger with damaged cord or plug—

have them replacedimmediately.

• Do not operate charger if it has received a sharp blow,

been dropped, or otherwise damaged in any way. Take it

to an authorised servicecentre.

• Do not disassemble charger; take it to an authorised

service centre when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution

orfire.

• In case of damaged power supply cord, the supply cord must

be replaced immediately by the manufacturer, its service agent

or similar qualified person to prevent anyhazard.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect two chargerstogether.

• The charger is designed to operate on standard 220‑

240V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

ENGLISH

Charging a Battery (Fig.B)

1. Plug the charger into an appropriate outlet before inserting

batterypack.

2. Insert the battery pack 11 into the charger, making sure the

battery pack is fully seated in the charger. The red (charging)

light will blink repeatedly indicating that the charging

process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is fully

charged and may be used at this time or left in the charger.

To remove the battery pack from the charger, push the

battery release button 12 on the batterypack.

NOTE: To ensure maximum performance and life of lithium‑ion

battery packs, charge the battery pack fully before firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

Charge Indicators

FCharging I

GFully Charged J

HHot/Cold Pack Delay* K

* The red light will continue to blink, but a yellow indicator light

will be illuminated during this operation. Once the battery pack

has reached an appropriate temperature, the yellow light will

turn off and the charger will resume the chargingprocedure.

The compatible charger(s) will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing tolight.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and battery

pack to be tested at an authorised servicecentre.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery pack has reached an appropriate

temperature. The charger then automatically switches to the

pack charging mode. This feature ensures maximum battery

packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan designed

to cool the battery pack. The fan will turn on automatically

when the battery pack needs to be cooled. Never operate the

charger if the fan does not operate properly or if ventilation slots

are blocked. Do not permit foreign objects to enter the interior

of thecharger.

Electronic Protection System

XR Li‑Ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deepdischarge.

The tool will automatically turn off if the Electronic Protection

System engages. If this occurs, place the lithium‑ion battery

pack on the charger until it is fullycharged.

Wall Mounting

These chargers are designed to be wall mountable or to sit

upright on a table or work surface. If wall mounting, locate the

charger within reach of an electrical outlet, and away from a

corner or other obstructions which may impede air flow. Use

the back of the charger as a template for the location of the

mounting screws on the wall. Mount the charger securely using

drywall screws (purchased separately) at least 25.4mm long

with a screw head diameter of 7–9mm, screwed into wood to

an optimal depth leaving approximately 5.5mm of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using a

cloth or soft non‑metallic brush. Do not use water or any

cleaning solutions. Never let any liquid get inside the tool;

never immerse any part of the tool into aliquid.

Battery Packs

Important Safety Instructions for All

BatteryPacks

When ordering replacement battery packs, be sure to include

catalogue number andvoltage.

The battery pack is not fully charged out of the carton. Before

using the battery pack and charger, read the safety instructions

below. Then follow charging proceduresoutlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Inserting or removing the battery from the charger may

ignite the dust orfumes.

• Never force battery pack into charger. Do not modify

battery pack in any way to fit into a non‑compatible

charger as battery pack may rupture causing serious

personalinjury.

• Charge the battery packs only in DeWALTchargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in locations

where the temperature may fall below 4˚C (39.2˚F)

(such as outside sheds or metal buildings in winter), or

reach or exceed 40˚C (104˚F) (such as outside sheds or

metal buildings insummer).

ENGLISH

9Hazardous Material. In general, only shipments containing a

lithium‑ion battery with an energy rating greater than 100Watt

Hours (Wh) will require being shipped as fully regulated Class 9.

All lithium‑ion batteries have the Watt Hour rating marked on

the pack. Furthermore, due to regulation complexities, DeWALT

does not recommend air shipping lithium‑ion battery packs

alone regardless of Watt Hour rating. Shipments of tools with

batteries (combo kits) can be air shipped as excepted if the Watt

Hour rating of the battery pack is no greater than 100Wh.

Regardless of whether a shipment is considered excepted

or fully regulated, it is the shipper's responsibility to consult

the latest regulations for packaging, labeling/marking and

documentationrequirements.

The information provided in this section of the manual is

provided in good faith and believed to be accurate at the time

the document was created. However, no warranty, expressed or

implied, is given. It is the buyer’s responsibility to ensure that its

activities comply with the applicableregulations.

Transporting the FLEXVOLTTM Battery

The DeWALT FLEXVOLTTM battery has two modes: Use

andTransport.

Use Mode: When the FLEXVOLTTM battery stands alone or is in

a DeWALT 18V(20V Max) product, it will operate as an 18V(20V

Max) battery. When the FLEXVOLTTM battery is in a 54V(60V Max)

or a 108V (120V Max)(two 54V (60V Max)batteries) product, it

will operate as a 54V(60V Max)battery.

Transport Mode: When the cap is attached to the FLEXVOLTTM

battery, the battery is in Transport mode. Keep the cap

forshipping.

When in Transport mode, strings

of cells are electrically

disconnected within the pack

resulting in 3batteries with a

lower Watt hour (Wh) rating as compared to 1battery with a

higher Watt hour rating. This increased quantity of 3batteries

with the lower Watt hour rating can exempt the pack from

certain shipping regulations that are imposed upon the higher

Watt hour batteries.

For example, the Transport

Wh rating might indicate

3x36Wh, meaning

3batteries of 36Wh each.

The Use Wh rating might

indicate 108Wh (1batteryimplied).

Storage Recommendations

1. The best storage place is one that is cool and dry away

from direct sunlight and excess heat or cold. For optimum

battery performance and life, store battery packs at room

temperature when not inuse.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool, dry place out of the charger for

optimalresults.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be recharged

beforeuse.

Example of Use and Transport Label Marking

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium‑ion battery packs areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open eye

for 15minutes or until irritation ceases. If medical attention

is needed, the battery electrolyte is composed of a mixture of

liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek

medicalattention.

WARNING: Burn hazard. Battery liquid may be flammable

if exposed to spark orflame.

WARNING: Never attempt to open the battery pack for

any reason. If battery pack case is cracked or damaged,

do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that

has received a sharp blow, been dropped, run over or

damaged in any way (i.e., pierced with a nail, hit with

a hammer, stepped on). Electric shock or electrocution

may result. Damaged battery packs should be returned to

service centre forrecycling.

WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do not place

the battery pack in aprons, pockets, tool boxes, product kit

boxes, drawers, etc., with loose nails, screws, keys,etc.

CAUTION: When not in use, place tool on its side on

a stable surface where it will not cause a tripping

or falling hazard. Some tools with large battery packs

will stand upright on the battery pack but may be easily

knockedover.

Transportation

WARNING: Fire hazard. Transporting batteries can

possibly cause fire if the battery terminals inadvertently

come in contact with conductive materials. When

transporting batteries, make sure that the battery

terminals are protected and well insulated from

materials that could contact them and cause a short

circuit. NOTE: Lithium‑ion batteries should not be put in

checkedbaggage.

DeWALT batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards which

include UN Recommendations on the Transport of Dangerous

Goods; International Air Transport Association (IATA) Dangerous

Goods Regulations, International Maritime Dangerous Goods

(IMDG) Regulations, and the European Agreement Concerning

The International Carriage of Dangerous Goods by Road

(ADR). Lithium‑ion cells and batteries have been tested to

section 38.3of the UN Recommendations on the Transport of

Dangerous Goods Manual of Tests andCriteria.

In most instances, shipping a DeWALT battery pack will be

excepted from being classified as a fully regulated Class

ENGLISH

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the

labels on the charger and the battery pack may show the

followingpictographs:

LRead instruction manual beforeuse.

p See Technical Data for chargingtime.

q Do not probe with conductiveobjects.

r Do not charge damaged batterypacks.

s Do not expose towater.

t Have defective cords replacedimmediately

u Charge only between 4˚C and 40˚C.

v Only for indooruse.

x Discard the battery pack with due care for

theenvironment.

y Charge DeWALT battery packs only with designated

DeWALT chargers. Charging battery packs other than

the designated DeWALT batteries with a DeWALT

charger may make them burst or lead to other

dangeroussituations.

z Do not incinerate the batterypack.

B USE (without transport cap). Example: Wh rating

indicates 108Wh (1battery with 108Wh).

A TRANSPORT (with built‑in transport cap). Example: Wh

rating indicates 3x 36Wh (3batteries of 36Wh).

Battery Type

The following tools operate on a 18(20 Max) volt battery pack:

DCD800, DCD805.

These battery packs may be used: DCB181, DCB182, DCB183,

DCB184, DCB203, DCB204, DCB205, DCB185,DCB186, DCB187,

DCB189, DCB240,DCBP034, DCB546, DCB547, DCB548, DCB549

,DCB606,DCB609,DCB612,DCB615. Refer to Technical Data for

moreinformation.

Package Contents

The package contains:

1 Drill/driver or 1 drill/driver/hammerdrill

1 Charger

1 Kitbox

1 Li‑Ion battery pack (C1, D1, E1, L1, M1, P1, S1, T1, X1, Y1

models)

2 Li‑Ion battery packs (C2, D2, E2, L2, M2, P2, S2, T2, X2, Y2

models)

3 Li‑Ion battery packs (C3, D3, E3, M3, P3, S3, T3, X3, Y3 models)

1 Instruction manual

NOTE: Battery packs, chargers and kitboxes are not included

with N models. Battery packs and chargers are not included with

NT models. Bmodels include Bluetooth® batterypacks.

NOTE: The Bluetooth® word mark and logos are registered

trademarks owned by the Bluetooth®, SIG, Inc. and any use of

such marks by DeWALT is under license. Other trademarks and

trade names are those of their respectiveowners.

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Markings on Tool

The following pictograms are shown on the tool:

a Read instruction manual beforeuse.

n Visible radiation. Do not stare intolight.

Date Code Position (Fig.B)

The date code 14, which also includes the year of manufacture,

is printed into thehousing.

Example:

2021XX XX

Year and Week of Manufacture

Description (Fig.A)

WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

1 Trigger switch

2 Forward/reverse control button

3 Torque adjustment collar

4 Gear shifter

5 Worklight

6 Keyless chuck

7 Chuck sleeve

8 Belt hook

9 Mounting screw

10 Bit holder

11 Battery pack

12 Battery release button

13 Worklight switch

Intended Use

These drills/drivers/hammerdrills are designed for professional

drilling, percussion drilling and screwdrivingapplications.

ENGLISH

DO NOT use under wet conditions or in the presence of

flammable liquids orgases.

These drills/drivers/hammerdrills are professional powertools.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

withoutsupervision.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

WARNING: Use only DeWALT battery packs andchargers.

Inserting and Removing the Battery Pack

from the Tool (Fig.B)

NOTE: Make sure your battery pack 11 is fullycharged.

To Install the Battery Pack into the Tool Handle

1. Align the battery pack 11 with the rails inside the tool’s

handle (Fig. B).

2. Slide it into the handle until the battery pack is firmly seated

in the tool and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the battery release button 12 and firmly pull the

battery pack out of the toolhandle.

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs (Fig.B)

Some DeWALT battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge

button15. A combination of the three green LED lights will

illuminate designating the level of charge left. When the level

of charge in the battery is below the usable limit, the fuel gauge

will not illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end‑userapplication.

Belt Hook and Magnetic Bit Holder (Fig.A)

Optional Accessories

WARNING: To reduce the risk of serious personal

injury, ONLY use the tool's belt hook to hang the

tool from a work belt. DO NOT use the belt hook for

tethering or securing the tool to a person or object during

use. DO NOT suspend tool overhead or suspend objects

from the belthook.

WARNING: To reduce the risk of serious personal

injury, ensure the screw holding the belt hook issecure.

CAUTION: To reduce the risk of personal injury or

damage, DO NOT use the belt hook to hang the drill

while using as aspotlight.

IMPORTANT: When attaching or replacing the belt hook8 or

magnetic bit holder10 , use only the mounting screw9 that is

provided. Be sure to securely tighten thescrew.

The belt hook and magnetic bit holder can be be attached

to either side of the tool using only the screw provided, to

accommodate left‑ or right‑ handed users. If the hook or

magnetic bit holder is not desired at all, it can be removed from

thetool.

To move belt hook or bit clip, remove the screw that holds it in

place then reassemble on the opposite side. Be sure to securely

tighten thescrew.

Variable Speed Trigger Switch (Fig.A)

To turn the tool on, squeeze the variable speed

triggerswitch1. To turn the tool off, release the trigger switch.

Your tool is equipped with a brake. The chuck will stop as soon

as the trigger switch is fullyreleased.

NOTE: Continuous use in variable speed range is not

recommended. It may damage the switch and should

beavoided.

Forward/Reverse Control Button (Fig.A)

A forward/reverse control button2 determines the direction of

the tool and also serves as a lock‑offbutton.

To select forward rotation, release the trigger switch and

depress the for ward/re verse control button on the right side of

thetool.

To select reverse, release the trigger switch and depress the

forward/reverse control button on the left side of thetool.

The centre position of the control button locks the tool in the off

position. When changing the position of the control button, be

sure the trigger isreleased.

NOTE: The first time the tool is run after changing the direction

of rotation, you may hear a click on start up. This is normal and

does not indicate aproblem.

Torque Adjustment Collar (Fig.A)

Your tool has an adjustable torque screwdriver mechanism for

driving and removing a wide array of fastener shapes and sizes

and in some models, a hammer mechanism for drilling into

masonry. Circling the torque adjustment collar3 are numbers,

a drill bit symbol, and on some models, a hammer symbol.

These numbers are used to set the clutch to deliver a torque

ENGLISH

range. The higher the number on the collar, the higher the

torque and the larger the fastener which can be driven. To select

any of the numbers, rotate until the desired number aligns with

thearrow.

Dual Range Gearing (Fig.A)

The dual range feature of your drill/driver allows you to shift

gears for greaterversatility.

1. To select speed 1(high torque setting), turn the tool off and

permit it to stop. Slide the gear shifter4 forward (towards

thechuck).

2. To select speed 2(low torque setting), turn the tool off and

permit it to stop. Slide the gear shifter back (away from

thechuck).

NOTE: Do not change gears when the tool is running. Always

allow the drill to come to a complete stop before changing

gears. If you are having trouble changing gears, make sure that

the dual range gear shifter is either completely pushed forward

or completely pushedback.

Pivoting LED Worklight (Fig.A, E)

CAUTION: Do not stare into worklight. Serious eye

injury couldresult.

The worklight 5 located on the foot of the tool is activated

when the trigger switch is depressed and is adjustable via three

detent positions. The off 17 , on 18 , and spotlight 19 modes

can be changed by moving the worklight switch 13 on the foot

of tool. In the on setting, the worklight will stay illuminated for

up to 20 seconds. If the trigger switch remains depressed, the

worklight will remain on.

NOTE: The worklight is for lighting the immediate work surface

and are not intended to be used as aflashlight.

Spotlight Mode

The spotlight will run for 20 minutes after the trigger switch is

released. Two minutes before the spotlight will shut off, it will

flash twice and then dim. To avoid the spotlight shutting off,

lightly tap the triggerswitch.

WARNING: While using the worklight in medium or

spotlight mode, do not stare at the light or place the

drill in a position which may cause anyone to stare

into the light. Serious eye injury couldresult.

CAUTION: When using the tool as a spotlight, be sure

it is secured on a stable surface where it will not cause a

tripping or fallinghazard.

CAUTION: Remove all accessories from the chuck before

using the drill as a spotlight. Personal injury or property

damage couldresult.

Low Battery Warning

When in spotlight mode and the battery is nearing complete

discharge, the spotlight will flash twice and then dim. After two

minutes, the battery will be completely discharged and the

drill will immediately shut down. At this point, replace with a

freshbattery.

WARNING: To reduce the risk of injury, always have a

back‑up battery or secondary lighting available if the

situation warrantsit.

Keyless Single Sleeve Chuck (Fig.C)

WARNING: Do not attempt to tighten drill bits (or

any other accessory) by gripping the front part of the

chuck and turning the tool on. Damage to the chuck

and personal injury may result. Always lock off trigger

switch and remove the battery from the tool when

changingacces sories.

WARNING: Always ensure the bit is secure before starting

the tool. A loose bit may eject from tool causing possible

personalinjury.

Your tool features a keyless chuck6 with one rotating chuck

sleeve7 for one‑handed operation of the chuck. To insert a drill

bit or other accessory, follow thesesteps.

1. Turn tool off and remove the battery pack.

2. Grasp the black sleeve of the chuck with one hand and

use the other hand to secure the tool. Rotate the sleeve

anticlockwise (as viewed from the front) far enough to

accept the desiredaccessory.

3. Insert the accessory about 19mm into the chuck and

tighten securely by rotating the chuck sleeve clockwise

with one hand while holding the tool with the other hand.

Continue to rotate the chuck sleeve until several ratchet

clicks are heard to ensure full grippingpower.

NOTE: Be sure to tighten chuck with one hand on

the chuck sleeve and one hand holding the tool for

maximumtightness.

To release the accessory, repeat steps 1and 2above.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and

applicableregulations.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

Proper Hand Position (Fig.D)

WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.

WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the main handle16

and one hand on the batterypack.

Drill Operation (Fig.A,D)

WARNING: TO REDUCE THE RISK OF PERSONAL

INJURY, ALWAYS ensure workpiece is anchored or

clamped firmly. If drilling thin material, use a wood

“back‑up” block to prevent damage to thematerial.

1. Turn the collar3 to the drillsymbol.

ENGLISH

2. Select the desired speed/torque range using the

gear shifter4 to match the speed and torque to the

plannedoperation.

3. For Wood, use twist bits, spade bits, power auger bits or

hole saws. For Metal, use high‑speed steel twist drill bits

or hole saws. Use a cutting lubricant when drilling metals.

The exceptions are cast iron and brass which should be

drilleddry.

4. Always apply pressure in a straight line with the bit. Use

enough pressure to keep drill biting, but do not push hard

enough to stall the motor or deflect thebit.

5. Hold tool firmly with both hands to control the twisting

action of the drill. If model is not equipped with side handle,

grip drill with one hand on the handle and one hand on the

batterypack.

CAUTION: Drill may stall if overloaded causing a sudden

twist. Always expect the stall. Grip the drill firmly to control

the twisting action and avoidinjury.

6. IF DRILL STALLS, it is usually because it is being overloaded

or improperly used. RELEASE TRIGGER IMMEDIATELY,

remove drill bit from work, and determine cause of stalling.

DO NOT CLICK TRIGGER ON AND OFF IN AN ATTEMPT

TO START A STALLED DRILL — THIS CAN DAMAGE

THEDRILL.

7. To minimise stalling or breaking through the material,

reduce pressure on drill and ease the bit through the last

fractional part of thehole.

8. Keep the motor running when pulling the bit back out of a

drilled hole. This will help preventjamming.

9. With variable speed drills there is no need to centre punch

the point to be drilled. Use a slow speed to start the hole

and accelerate by squeezing the trigger harder when the

hole is deep enough to drill without the bit skippingout.

Hammerdrill Operation (Fig.A,D)

DCD805only

1. Turn the collar3 to the hammerdrillsymbol.

2. Select the high speed setting by sliding the gear shifter4

back (away from thechuck).

IMPORTANT: Use carbide‑tipped or masonry bitsonly.

3. Drill with just enough force on the hammer to keep it from

bouncing excessively or “rising” off the bit. Too much force

will cause slower drilling speeds, overheating and lower

drillingrate.

4. Drill straight, keeping the bit at a right angle to the work. Do

not exert side pressure on the bit when drillling as this will

cause clogging of the bit flutes and a slower drillingspeed.

5. When drilling deep holes, if the hammer speed starts to

drop off, pull the bit partially out of the hole with tool still

running to help clear debris from thehole.

NOTE: A smooth, even flow of dust from the hole indicates

proper drillingrate.

Screwdriver Operation (Fig.A,D)

1. Turn the torque adjustment collar3 to the desiredposition.

2. Select the desired speed/torque range using the

gear shifter4 to match the speed and torque of the

plannedoperation.

NOTE: Use the lowest torque setting required to seat the

fastener at the desired depth. The lower the number, the

lower the torqueoutput.

3. Insert the desired fastener accessory into the chuck as you

would any drillbit.

4. Make some practice runs in scrap or on unseen areas to

determine the proper position of the clutchcollar.

5. Always start with lower torque settings, then advance to

higher torque settings to avoid damage to the workpiece

orfastener.

MAINTENANCE

Your power tool has been designed to operate over a long

period of time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care and

regularcleaning.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

The charger and battery pack are notserviceable.

Lubrication

Your power tool requires no additionallubrication.

Cleaning

WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.

WARNING: Never use solvents or other harsh chemicals

for cleaning the non‑metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Optional Accessories

WARNING: Since accessories, other than those offered

by DeWALT, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only DeWALT recommended

accessories should be used with thisproduct.

Consult your dealer for further information on the

appropriateaccessories.

ENGLISH

Protecting the Environment

wSeparate collection. Products and batteries marked

with this symbol must not be disposed of with

normal householdwaste.

Products and batteries contain materials that

can be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails

to produce sufficient power on jobs which were easily done

before. At the end of its technical life, discard it with due care for

ourenvironment:

• Run the battery pack down completely, then remove it from

thetool.

• Li‑Ion cells are recyclable. Take them to your dealer or a

local recycling station. The collected battery packs will be

recycled or disposed ofproperly.

AFTER SERVICE AND REPAIR

DEWALT service centers are staffed with trained personnel to

provide customers with efficient and reliable product service.

We do not take any responsibility when you have repaired

in unauthorized service center. You can refer to the leaflet of

CONTACT CENTER LOCATOR in product package and contact

us through hotline, website or social media to find the nearest

DEWALT service center around you

简体中文

DCD800-B1/A9/TW/KR DCD805-B1/A9/TW/KR DCD805-JP

电压 VDC 18(20 Max) 18(20 Max) 18

电池类型锂离子锂离子锂离子

空载转速

第一档转/分 0–650 0–650 0–650

第二档转/分 0–2000 0–2000 0–2000

冲击频率

第一档转/分 —0–11050 0–11050

第二档转/分 —0–34000 0–34000

最大扭矩 Nm 90/27 90/27 90/27

夹头尺寸毫米 1.5–13.0 1.5–13.0 1.5–13.0

最大钻孔尺寸

木材毫米 55 55 55

金属毫米 13 13 13

砖石结构毫米 —13 13

重量（不含电池包）千克 1.28 1.34 1.34

恭喜！

感谢您选购

DeWALT

工具凭借多年的产品开发和创新经验，

DeWALT

已经成为专业电动工具用户最可靠的合作伙伴之一。

技术数据

20V

锂电无刷紧凑电钻起子

DCD800

20V 锂电无刷紧凑冲击钻

DCD805

English (original instructions)

电池充电器/充电时间（分钟）

型号电压安时重量（ kg）DCB104 DCB107 DCB112 DCB115 DCB117 DCB118 DCB132 DCB1112

DCB546/DCB606 18/54 (20/60 Max) 6.0/2.0 1.08 60 270 170 90 40 60 90 40

DCB547/DCB609 18/54 (20/60 Max) 9.0/3.0 1.46 75* 420 270 135* 60 75* 135* 60

DCB548/DCB612 18/54 (20/60 Max) 12.0/4.0 1.46 120 540 350 180 80 120 180 80

DCB549/DCB615 18/54 (20/60 Max) 15.0/5.0 2.12 125 730 450 230 90 125 230 90

DCB181 18 (20 Max) 1.5 0.35 22 70 45 22 22 22 22 22

DCB182/DCB204 18 (20 Max) 4.0 0.61 60/40** 185 120 60 60/40** 60/40** 60 60/40**

DCB183/DCB203 18 (20 Max) 2.0 0.40 30 90 60 30 30 30 30 30

DCB184/DCB205 18 (20 Max) 5.0 0.62 75/50** 240 150 75 75/50** 75/50** 75 75/50**

DCB185 18 (20 Max) 1.3 0.35 22 60 40 22 22 22 22 22

DCB187 18 (20 Max) 3.0 0.54 45 140 90 45 45 45 45 45

DCB189/DCB240 18 (20 Max) 4.0 0.54 60 185 120 60 60 60 60 60

DCB186 18 (20 Max) 6.0 0.95 60 270 170 90 60 60 90 60

DCBP034 18 (20 Max) 1.7 0.32 27 82 50 27 27 27 27 27

日期码

201811475B

或以后

日期码

201536

或以后

简体中文

警告：为降低伤害风险，请阅读使用手册。

定义：安全指南

下列定义描述了各标志术语的严重程度。请仔细阅读本手册，并注

意这些标志。



危险：表示存在紧急危险情况，如果不加以避免，将导致死

亡或严重伤害。



警告：表示存在潜在的危险情况，如果不加以避免，可能导

致死亡或严重伤害。



警示：指示潜在的危险情况，如不加以避免，可能导致轻度

或中度伤害。

注意：表示存在不涉及人身伤害的情况，如果不加以避免，

可能导致财产损失。



指示有触电风险。



指示存在火灾风险。

电动工具通用安全警告



警告：阅读随该电动工具提供的所有安全警告、说明、图解

和规定。不了解以下所列所有说明将导致触电、火灾和/或

严重伤害。

请保存所有警告和说明书以备查阅

警告中的术语“电动工具”指的是电驱动（有线）电动工具或电池驱动

（无线）电动工具。

1) 工作场地的安全

a )

保持工作区清洁和明亮。杂乱的工作区及操作台会引发

事故。

b )

请勿在易爆环境，如有易燃液体、气体或粉尘的环境下操作

电动工具。电动工具产生的火花会点燃粉尘或气体。

c )

操作电动工具时，请让儿童和旁观者远离。注意力不集中会

使你失去对工具的控制。

2) 电气安全

a )

电动工具插头必须与插座相配。不得以任何方式改装插头。

需接地的电动工具不能使用任何转换插头。未经改装的插

头和相配的插座将降低触电风险。

b )

避免人体接触接地表面，如管道、散热片和冰箱。如果身体

接触接地表面，会增加触电风险。

c )

请勿将电动工具暴露在雨中或潮湿环境中。水进入电动工

具将增加触电风险。

d )

请勿滥用软线。不得通过拉拽软线的方式搬运、拉动电动工

具或拔出插头。请让软线远离热源、油、锐边或转动部件。受

损或缠绕的软线会增加触电风险。

e )

在户外使用电动工具时，请使用适合户外使用的延长线。适

合户外使用的电线会降低触电风险。

f )

如果无法避免在潮湿环境下操作电动工具，应使用带有

剩余电流装置

(RCD)

保护的电源。

RCD

的使用可降低触电

风险。

3) 人身安全

a )

保持警觉，当操作电动工具时关注所从事的操作并保持清

醒。当您感到疲倦，或在出现药物、酒精或治疗反应时，请

勿操作电动工具。在操作电动工具时，瞬间的疏忽会导致

严重人身伤害。

Batteries

Chargers/Charge Times (Minutes)

Cat #

Weight

*Date code 201811475B or later

**Date code 201536 or later

b )

使用个人防护装置。

始终佩戴护目镜。防护装置，诸如适当

条件下使用防尘面具、防滑安全鞋、安全帽、听力防护等装

置能减少人身伤害。

c )

防止意外启动。在连接电源和/或电池盒、拿起或搬运工具

前确保开关处于关断位置。搬运工具时，将手指搭在开关

上，或在开关处于接通状态时连通电源，会导致危险。

d )

在电动工具接通之前，拿掉所有调节钥匙或扳手。遗留在电

动工具旋转零件上的扳手或钥匙会导致人身伤害。

e )

请勿将手过分伸展。时刻保持身体平衡，并找到合适的落脚

点。这样能在意外情况下能更好地控制住电动工具。

f )

适当着装。请勿穿宽松衣服或佩戴饰品。长发人员应佩戴防

护性发套。防止将服装或首饰卷入活动的部件中。

g )

如果该设备配有用来连接吸尘和集尘设备的装置，请确保

它们已连接好并能恰当使用。使用集尘装置可降低粉尘引

起的危险。

h )

请勿因为频繁使用工具而产生的熟悉感而掉以轻心，忽

视工具的安全准则。某个粗心的动作可能在瞬间导致严重

的伤害。

4) 电动工具使用和注意事项

a )

请勿勉强使用电动工具，根据用途使用合适的电动工具。

选用合适的按照额定值设计的电动工具会使您的工作更

有效、更安全。

b )

如果开关不能接通或关断电源，则不能使用该电动工具。无

法通过开关来控制的电动工具是危险的且必须进行修理。

c )

在进行任何调节、更换附件或贮存电动工具之前，必须从电

源上拔掉插头和/或卸下电池包（如可拆卸）。这种防护性的

安全措施降低了电动工具意外启动的风险。

d )

将闲置不用的电动工具存放在儿童所及范围之外，并且不

允许让不熟悉电动工具和不了解这些说明的人操作电动工

具。电动工具在未经培训的使用者手中是危险的。

e )

维护电动工具及其附件。检查运动部件是否调整到位或卡

住，检查零件破损情况和影响电动工具运行的其他状况。如

有损坏，应在使用前修理好电动工具。许多事故是由维护不

良的电动工具引发的。

f )

保持切削刀具锋利和清洁。维护良好地有锋利切削刃的刀

具不易卡住而且容易控制。

g )

按照使用说明书，并考虑作业条件和要进行的作业来选择

电动工具、附件和工具的刀头等。将电动工具用于那些与其

用途不符的操作可能会导致危险情况。

h )

保持手柄和握持表面干燥、清洁，不油腻。在意外的情况下，

湿滑的手柄不能保证握持的安全和对工具的控制。

5) 电池式工具使用和注意事项

a )

仅使用生产者规定的充电器充电。将适用于某种电池包的

充电器用到其他电池包时可能会发生着火危险。

b )

仅使用配有专用电池包的电动工具。使用其他电池包可能

会产生伤害和着火危险。

c )

当电池包不用时，将它远离其他金属物体，例如回形针、硬

币、钥匙、钉子、螺钉或其他小金属物体，以防电池包一端与

另一端连接。电池包端部短路会引起燃烧或着火。

d )

在滥用条件下，液体可能会从电池包中溅出，应避免接触。

如果意外碰到液体，用水冲洗。如果液体碰到了眼睛，还

要寻求医疗帮助。从电池中溅出的液体可能会发生腐蚀

或燃烧。

简体中文

e )

请勿使用损坏或改装过的电池包或工具。损坏或改装过的

电池包可能呈现无法预测的结果，导致火灾、爆炸或伤害。

f )

请勿将电池包暴露于火或者高温中。如果电池包暴露于明

火或高于

130°C

的高温中，可能会爆炸。

g )

请遵循所有充电说明，请勿在说明中规定的温度范围以外

的环境对电池包或工具充电。不当充电，或在指定范围以外

的温度下充电，可能导致电池损坏并增加火灾风险。

6) 维修

a )

让专业维修人员使用相同的备件维修电动工具。这能保证

所维修的电动工具的安全。

b )

不得维修损坏的电池包。电池包仅能由制造商或其授权的

维修服务商进行维修。

针对电钻的额外安全规则

•

佩戴耳罩进行冲击作业。暴露于噪声环境会导致失聪。

•

使用辅助手柄。失控会导致人身伤害。

•

工具使用前应得到适当支撑。由于工具输出转矩大，运行时没

有适当支撑会失控导致人身伤害。

•

当在钻削附件可能触及暗线之处进行操作时，要通过绝缘握持

面来握持工具。钻削附件碰到带电导线会使工具外露的金属零

件带电从而使操作者受到电击。

针对使用长钻头时的安全说明

•

电钻运转速度不得高于钻头的最高额定速度。在超速的情况

下，如果钻头自由转动而不接触工件，那么钻头可能会弯折，从

而导致人员受伤。

•

务必从低转速开始钻孔，而且要让钻头接触工件。在超速的情

况下，如果钻头自由转动而不接触工件，那么钻头可能会弯折，

从而导致人员受伤。

•

只可沿着钻头的方向直线施压，请勿施加过大压力。钻头可能

会弯折，造成损坏或失控，导致人员受伤。

•

使用夹钳或其他方法将工件固定和支撑在一个稳定的平台上。

用手扶住工件或用身体抵住工件都是不稳定的，可能会让工

具失控。

•

如果长时间使用电钻，请佩戴听力保护设备。长时间暴露在高

强度的噪音环境中会导致听力丧失。短暂听力丧失或严重耳鼓

受损可能源自电钻产生的高噪音水平。

•

佩戴护目镜或其他眼部保护设备。操作电钻，进行钻孔都会产

生飞溅的碎屑。飞溅颗粒会对眼睛造成永久损伤。

•

电钻的钻头和工具在运转过程中会发热。如需触碰，请佩戴

手套。

•

请勿长时间操作该工具。电钻所产生的振动会损伤您的双手和

双臂。请佩戴手套为您提供额外缓冲，同时请定期休息，以限制

自己对振动的暴露程度。

•

通风口通常会遮盖转动部件，应注意避免。宽松衣物、珠宝或

长发会卡在转动部件中。宽松衣服、珠宝或长发可能会卷入转

动部件。

剩余风险

尽管遵守了相关的安全法规并采用了安全装备，某些剩余风险依然

无法避免。这些风险包括：

•

听力损伤。

•

飞溅颗粒造成的人身伤害风险。

•

使用时附件发热导致的灼伤风险。

•

长时间使用引起的人身伤害风险。

请妥善保管好这些说明

充电器

DeWALT

充电器无需做出任何调整，专为简易操作而设计。

电气安全

电机只适用一种工作电压。请务必检查电池包的电压是否和铭牌上

的电压一致。另外，请确保充电器电压和主电源的电压一致。

DeWALT

充电器符合 IeC60335 双重绝缘要求，因此无需使

用接地线。

如果电源线损坏，必须由

DeWALT

或授权的维修机构负责更换。

使用延长线

除非绝对必要，否则请勿使用延长线。使用适合您的充电器输入功

率的合格延长线（请参阅

技术数据

）。最小的导线尺寸为 1 平方毫

米；最大长度为 30 米。

使用电缆卷筒时，请务必拉出所有的电缆。

针对所有电池充电器的重要安全说明

请妥善保管好这些说明：

本手册包含重要的兼容电池充电器安全和

操作说明（请参阅

技术数据

）。

•

在使用充电器之前，请先阅读所有指示以及充电器、电池包和

使用电池包的产品上的警告标记。



警告：触电危险。请勿让任何液体进入充电器，否则可能会

导致触电。



警告：我们建议使用漏电保护额定电流为 30 毫安或以下的

漏电保护装置。



小心：灼伤危险。为降低人身伤害风险，请仅使用

DeWALT

充

电式电池充电。使用其它类型的电池可能会引起爆裂，并导

致人身伤害和损害。



小心：应看管好儿童，以确保他们不将此设备当做玩具来玩。

注意：在某些情况下，当充电器的插头插入电源插座时，充

电器内部裸露的充电接触点可能因为外来物件而短路。请

勿让能导电的异物靠近充电器腔，这些外来物件包括但不

限于钢棉、铝箔或任何金属颗粒的堆积物。充电器内没有

电池包时，请断开充电器与电源的连接。清洗前，务必拔掉

充电器。

•

请勿试图使用本手册指定的充电器以外的其他任何充电器为

电池包充电。充电器和电池包都是专门设计的，互相配合使用。

•

除了为

DeWALT

充电式电池充电以外，这些充电器并非设计用

于其他用途。否则，可能会导致火灾、触电或电击。

•

请勿将充电器暴露于雨中或雪中。

•

断开充电器连接时，应捏住插头将其拔下，而非通过拉拽电源

线拔下插头。这将降低对电插头和电线的损害风险。

•

确保电源线布置在不易踩踏、踢绊、拉扯或会受到损害或压力

的位置。

•

除非绝对必要，否则请勿使用延长线。使用不正确的延长线可

能导致火灾、触电或电击的风险。

•

请勿将任何物件放在充电器上面，或是把充电器放在可能会

堵住通风槽的柔软表面，导致充电器的内部过热。请把充电器

放置在远离任何热源的地方。充电器通过外壳顶端和底端的

槽进行通风。

•

请勿使用电源线或插头已损坏的充电器，请立即更换这些充

电器。

简体中文

•

如果充电器受到强烈重击、掉落或出现其他损坏情况，请勿使

用充电器。请将损坏的充电器送到授权服务中心。

•

请勿自行拆卸充电器。请将需要检修或修理的充电器送到授权

服务中心。重装不正确可能导致触电、电击或火灾风险。

•

必须立即将已损坏的电源线交由制造商、服务代理或类似的合

格人员进行更换以防止安全隐患。

•

清洁前，请先断开充电器和插座的连接，以降低触电风险。取出

电池包不会降低此风险。

•

不得将两个充电器连接在一起。

•

充电器是为

220V

的标准家用电源而设计。请勿试图在任何其

他电压下使用充电器。此规则不适用于车载充电器。

为电池充电（图 B）

1. 插入电池包前，先将充电器的插头插到相应的电源插座上。

2. 将电池包 11 插入到充电器中，确定电池包完全就位。红色（充

电中）指示灯将不断闪烁，表示充电过程已经开始。

3. 红色灯常亮表示充电完成。此时电池包已完全充电，您可以使用

电池包或将电池包留在充电器上。如需从充电器上取下电池包，

请按下电池包上的电池释放按钮 12 。

注意：为了确保锂离子电池的效能和使用寿命最大化，在首次使用

电池包之前必须将其充满电量。

充电器操作

关于电池包的充电状态，请参阅以下指示灯说明。

充电状态指示灯

F充电中 I

G已完全充电 J

H热/冷电池包延迟* K

* 红色指示灯会继续闪烁，但黄色指示灯在本次操作过程中会亮

起。电池包达到适当温度后，黄色指示灯会熄灭，充电器将恢复充

电程序。

兼容充电器不会对故障电池包充电。充电器指示灯不亮时表示电

池有故障。

注意：这可能也表示充电器有问题。

如果充电器提示存在故障，请将充电器和电池包送到授权的服务

中心进行测试。

高温/低温电池包延迟

当充电器检测到电池包过热或过冷时，它会自动启动热/冷电池延

迟模式，暂停充电，直到电池包达到适当的温度。然后，充电器会自

动切换到电池包充电模式。此功能可确保电池包拥有最长的使用

寿命。

冷电池包充电速度比热电池包充电速度慢。电池包在整个充电周期

的充电速度都会较慢，即使电池包升温也不会恢复到最大速度。

DCB118 充电器配备专用于冷却电池包的内部风扇。电池包需要冷却

时，风扇会自动启动。如果风扇运转不正常或通风槽堵塞，不得操作

充电器。请勿让异物进入充电器内部。

电子保护系统

XR 锂离子电池工具采用了电子保护系统设计，可让电池包免受过

载、过热或过度放电之害。

如果电子保护系统处于运作状态，该工具将自动停止操作。如果发

生这种情况，请将锂离子电池包放在充电器上，直至电量充满为止。

壁挂式安装

这些充电器设计为可以安装在墙上，也可以直立在桌面或工作台面

上。如果安装在墙上，请确保充电器的位置可以连接到电源插座，并

且远离墙角或其他可能妨碍空气流通的障碍物。将充电器背面作为

在墙上安装螺钉的位置模板。使用至少 25.4 毫米长、螺钉帽直径至

少7‑9 毫米的石膏板螺钉（单独购买）牢牢固定充电器，将螺钉最大

限度钉入木材，预留约 5.5 毫米露在墙外。将充电器背面的安装槽对

准露出的螺钉，完全放置到位。

充电器清洁说明



警告：触电危险。清洁前，请将充电器从交流电源插座上拔

下。可用布或非金属软刷清除充电器外部的污垢和油脂。请

勿使用水或任何清洁剂。不得让任何液体渗入工具，不得让

工具的任何部件浸在液体中。

电池包

针对所有电池包的重要安全说明

在订购更换电池包时，请务必附上目录型号和电压。

包装箱内的电池包并未完全充电。使用电池包和充电器之前，请阅

读下列安全说明，然后遵循所述的充电程序。请阅读所有说明

请阅读所有说明

•

请勿在易爆环境，如有易燃液体、气体或粉尘的环境中充电或

使用电池。在充电器中插入或取出电池时可能会点燃粉尘或

气体。

•

不得强行将电池放进充电器。请勿以任何方式改装电池包并将

电池包插入不兼容的充电器，这种操作可能会导致电池包破

裂，造成严重的人身伤害。

•

仅使用

DeWALT

充电器为电池充电。

•

请勿喷溅电池包或将其浸泡在水或其他液体中。

•

请勿在温度可能低于

4˚C (39.2˚F)

（如冬天户外的棚子或金属

建筑物中）, 或在温度可能达到或超过

40˚C (104˚F)

的地方（如

夏天户外的棚子或金属建筑物中）存储或使用工具和电池包。

•

即使电池包严重受损或完全损坏，也请勿焚化电池包。电池包

在火中会发生爆炸。锂离子电池包在燃烧时会释放有毒气体

和物质。

•

如果电池液体接触到皮肤，请立即以中性肥皂和清水冲洗接

触的地方。如果电池液体不慎进入眼睛，应睁开眼睛并用清水

冲洗至少

分钟或直到刺激感消失。如果需要医疗救助，请

告知医护人员。电池电解质由液状有机碳酸盐和锂盐的混合

物组成。

•

已打开电池的内部物质可能导致呼吸道刺激。请保持空气流

通。如果症状持续存在，请就医。



警告：灼伤危险。电池液如果接触到火花或火焰，可能会

燃烧。



警告：不得以任何理由试图打开电池包。电池包外壳破裂或

损坏时，请勿将电池包插入充电器。请勿挤压、掉落或损坏

电池包。请勿使用受过强烈重击、掉落、碾压或以任何其它

方式（如被钉子穿破、受到锤子的重击、踩踏）受损的电池包

或充电器。否则可能会引起触电或电击。损坏的电池包应送

回服务中心进行回收。



警告：火灾危险。请勿在存储或搬运电池包时让金属物品接

触暴露的电池两极。例如，请勿将电池包放在围裙、口袋、

工具盒、产品套件盒、抽屉等可能与散钉、螺丝、钥匙等物

品接触的地方。

简体中文



小心：不用时，将工具侧放在平稳的表面上，确保不会有踢

绊或掉落的危险。一些具有大型电池包的工具将直立于电

池包之上，但可能会轻易被撞倒。

运输 

警告：火灾危险。电池运输途中，如果电池两极意外接触导

电材料，可能会引发火灾。运输电池时，务必保护电池两极，

确保与可能接触电池导致短路的材料良好绝缘。注意：不应

将锂离子电池放入托运行李中。

DeWALT

电池符合所有适用的行业和法律标准规定的运输规范，包

括《联合国危险品运输建议规章范本》(UN Recommendations on the

Transport of Dangerous Goods)、《国际航空运输协会 (IATA) 危险品规则》

(International Air Transport Association(IATA) Dangerous Goods Regulations) 、

《国际海运危险品(IMDG) 规则》(International Maritime Dangerous Goods

(IMDG)Regulations) 和《欧洲危险货物国际公路运输协定》(European

Agreement Concerning The International Carriage of Dangerous Goods by

Road) (ADR)。离子电池和电池包已遵循《联合国危险品运输建议规章

范本手册》第 38.3 节关于测试和标准的说明通过测试。

大多数情况下，发运

DeWALT

电池包不属于完全管制的 9 类危险品。

通常情况下，只有当运输包含一个能量等级大于 100 瓦时（Wh）的

锂离子电池时，才需要作为完全管制的 9 类危险品发运。所有锂离

子电池外壳上均标注有瓦时等级。此外，由于法规比较复杂，无论瓦

时等级是多少，

DeWALT

都不建议单独空运锂离子电池包。发运包含

电池的工作（组合套件）时，如果电池包的能量等级不大于 100 瓦时

(Wh)，则可以按计划空运。

无论发运是否纳入完全管制范围内，运输公司均有责任遵循最新法

规中关于包装、标签/标记和单据的要求。

本手册本节的信息是出于善意提供，且认为在编制文档时准确无

误。是不提供明示或暗示的担保。购买方负有确保其行为遵守适用

法规的责任。

运输 FLEXVOLTTM 电池

DeWALT

FLEXVOLTTM电池有两种模式：使用和运输。

使用模式：若 FLEXVOLTTM 电池单独使用或在

DeWALT

18 伏特 (最大 20

伏特) 产品中使用时，将作为 18 伏特（最大 20 伏特) 特电池运作。若

FLEXVOLTTM 电池在 54 伏特 (最大 60 伏特)或 108伏特 (最大 120 伏特)

(2个 54 伏特 (最大 60 伏特)电池）产品中使用，将作为 54 伏特(最大

60 伏特) 电池运作。

运输模式：当电池盖连接到 FLEXVOLTTM 电池时，电池会进入运输模

式。保留电池盖用于运输。

处于运输模式时，电池包内部的电

池芯会处于断电状态，使 3 个低瓦

时 (Wh) 级的电池相当于 1 个高瓦

时等级电池。这样，增加 3 个低瓦

时等级的电池可以使电池包不必遵守适用于更高瓦时电池的运输

法规。

例如，若运输额定瓦时为

3 x 36瓦时，则表示 3 个 36

瓦时的电池。使用瓦时额定

值可能是 108 瓦时(表示 1

个电池)。

存放建议

1. 最好将电池存放在阴凉、干燥、远离阳光直射、不会过热或过冷

的地方。了获得最佳的电池性能和使用寿命，请您在不使用电池

包时将其存储在室温下。

使用和运输标签标记示例

2. 长期存储时，建议将完全充电的电池包从充电器取出，存储在阴

凉、干燥的地方，以达到最佳效果。

注意：电池包不应在电池已完全耗尽的状态下存放。使用电池包之

前，必须重新为电池包充电。

充电器和电池包上的标签

除了在本手册中所使用的标志，充电器和电池包的标签还包括：

L使用前请阅读使用手册。

p 如需了解充电时间详细信息，请参见

技术数据

。

q 请勿使用导电物体戳刺。

r 请勿对损坏的电池包充电。

s 请勿将其暴露于水中。

t 应立即更换有缺陷的电线。

u 请只在 4˚C 和 40°C 之间的温度下充电。

v 仅在室内使用。

x 弃置电池包时，请妥善处理，保护环境。

y 只使用指定的 Charge

DeWALT

充电器为

DeWALT

电池包充

电。使用

DeWALT

充电器为非

DeWALT

电池充电可能会导致

电池爆炸或出现其他危险情况。

z 请勿焚化电池包。

B 使用（无电池盖）。示例：瓦时额定值为 108 瓦时（ 1个 108 瓦

时的电池）。

A 运输（有内置运输盖）。示例：瓦时额定值为 3x 36 瓦时（ 3 个

36 瓦时的电池）。

电池类型

以下工具的运行需要 18伏特 (最大20伏特) 电池包：DCD800, DCD805。

这些电池包可用于：DCB181, DCB182, DCB183, DCB184, DCB203, DCB204,

DCB205, DCB185, DCB186, DCB187, DCB189, DCB240, DCBP034, DCB546,

DCB547, DCB548, DCB549, DCB606, DCB609, DCB612, DCB615。更多信息，

请参阅

技术数据

。

包装内的物品

包装内的物品包括：

1个电钻起子或1个冲击钻

1个充电器

1个工具箱

1个锂离子电池包（C1, D1, E1, L1, M1, P1, S1, T1, X1, Y1型号）

ページを読み込んでいます...

DeWalt DCD800P2T, DCD800D2T, DCD800E2T, DCD800M2T, DCD800N, DCD800NT ユーザーマニュアル

関連論文