4
2
70
3
4
Read the appliance's instructions
before installing and using.
The graphics in these Assembly
instructions are given as a guide only.
The manufacturer is exempt from
all
liability if this manual's
requirements
are not complied
with.
Attention!
According to the Gas Safety
Regulations of Hong Kong, any
gas installation works including
the installation of appliances and
connection tubing, must be
undertaken by registered gas
installers who are registered for
that appropriate classes and be
employed by registered gas
contractors.
Safety instructions
Connection of Town Gas rubber
tube
-Use approved gas tubing bearing
EMSD approval marking (example :
機電工程署批准EMSD APPROVAL
GTXXXX) for connection to
appliances, or other approval
methods by EMSD.
HK Town Gas connection
-Governor Beckley(2300) or Elitre EL-
125 should be installed.
Working pressure is 10mbar
Before installing, you need to check
that local distribution conditions (gas
type and pressure) and the
appliance's adjustment are
compatible. The appliance's
adjustment conditions are written on
the label or the specifications plate.
This appliance can only be installed
in a well-ventilated place in
accordance with existing regulations
and ventilation specifications. The
appliance must not be connected to a
combustion product evacuation
device.
The supply cable must be attached to
the unit to prevent it from touching hot
parts of the oven or hob.
Appliances with electrical supply must
be earthed.
Do not tamper with the appliance's
interior. If necessary, call our
mechanical Assistance Service.
When installing built-in gas hob on
top of stove cabinet, please check
that there is provision for
ventilation at the cabinet to ensure
proper operation of the gas hob.
Do not store any flammable
materials, sprays or pressurized
containers inside the stove
cabinet.
Before installing
This appliance is class 3 type,
according to the EN 30-1-1 regulation
for gas appliances: built-in appliance.
These individual appliances can be
combined with other identical
appliances and/or with conventional
hobs of the same make, using the
joint accessory.
See the catalogue for details.
The units next to the appliance must
be made of non-flammable materials.
The laminated covering and glue for
adhering it must be heat resistant.
This appliance cannot be installed
above fridges, washing machines,
dishwashers or similar.
An oven must have a power cooling
fan to install a hob above it.
Check the oven's dimensions in its
installation manual.
If an extractor fan is installed, you
must follow the installation manual's
instructions, always keeping a
minimum distance of 650 mm to the
hob.
Preparation of kitchen
unit (fig. 1-2)
Make an appropriate size cut in the
work surface.
If the hob is electric or mixed (gas
and electricity) and there is no oven
below, place a non-flammable
separator (e.g. metal or plywood) 10
mm from the bottom of the hob. This
will prevent access to the base of the
hob.
Appliance must not be converted
to another type of gas.
Please do not use additional fitting,
such as aluminum cover.
This appliance has been designed for
home use only. This appliance cannot
be installed on yachts or in caravans.
If the hob is gas, it is recommendable
to place the separator at the same
distance.
On wood work surfaces, varnish the
cutting surfaces with a special glue.
This protects them from moisture
which could collect under the work
surface.
The clips and the adhesive seal
(underside of the hob) are
factory-fitted: do not under any
circumstances remove them. The
seal ensures that the entire work
surface will be watertight, and
prevents water seepage.
In order to fit the appliance into the
kitchen unit, first place the hob in the
correct position then loosen each of
the clips so that they all turn freely (it
is not necessary to completely undo
them).
Insert and centre the hob.
Press the sides of the hob until it is
supported around its entire perimeter.
Turn the clips and tighten them fully.
Fig. 3
Removal of hob
Turn off the appliance's electricity and
gas supply.
Unscrew the clips and proceed in the
reverse order to installation.
Gas connection
The end of the inlet connection point
of the gas hob has a 1/2” thread that
allows for:
- fixed connection.
- connection using a flexible metal
pipe.
In this case, it is necessary to insert
the accessory (427950) and the
watertight seal (034308) supplied
between the manifold outlet and the
gas supply.
In this case, you must prevent the
pipe from coming into contact with
moving parts of the kitchen unit being
inserted (for example, a drawer) and
prevent access to any spaces which
might become obstructed.
If you need to connect the gas supply
horizontally, our Technical Assistance
Service can supply you with an
L-tube (code 173018) and a seal
(code 034308). Warning! If
any connection is handled, check the
seal. Danger of leaks.
The manufacturer is not liable for any
connection leaking, after being
handled.
Electric connection (fig. 4)
Check that the voltage and power of
the appliance are compatible with the
electrical installation.
The hobs are supplied with a power
cable with or without a wall socket
plug.
Provide an omnipolar cut-off switch
with a minimum contact separation of
3 mm (except for plug connections, if
the user has access to it).
Appliances with plugs must only be
connected to sockets that have earth
wires correctly installed.
This appliance is type “Y”: the supply
cable can only be changed by the
Technical Assistance Service and not
the user. The cable type and
minimum cross-section must be
respected.
安全說明
注意! 根據香港氣體安全規例，任何氣
體裝置工程，包括爐具和接駁喉管的安
裝，必須由註冊氣體裝置技工執行，而
該技工已於相關的氣體工程類別註冊
及受聘於註冊氣體工程承辦商。
本爐具僅可根據現行規例及通風規範
在良好通風之處安裝。爐具不得接駁至
抽油烟裝置。
香港煤氣接駁
接駁煤氣時須加上穩壓器
Beckley
10毫巴
注意: 涉及安裝、調校氣體等之所有操
作，必須由獲註冊氣體承辦商所雇用之
註冊氣體裝置技工遵照供氣及供電商
之適用規例、標準和規範進行。
安裝技師需注意氣體及電力供應商的
標準和規格。
安裝前，請關上爐具的供電及供氣。
要轉用另一種氣體，必須聯繫我們的技
術支援服務部。
本爐具設計成僅供家居使用。本爐具不
可裝於遊艇上或活動房屋內。
安裝前須檢查本地的供氣狀況(氣體種
類及氣壓)與爐具的調節相匹配。爐具
的調節條件載於標籤或規範銘牌上。
當在灶櫃面安裝嵌入式氣體煮食爐
時，灶櫃應設有透氣設施，以確保煮食
爐在使用時操作正常。
不應將易燃物料、噴霧及壓縮容器放置
在灶櫃內。
本爐具僅可根據現有規例及通風規範
在良好通風之處安裝。
爐具不得接駁至抽油烟裝置。
供電線必須直接接到爐具以防接觸爐
灶或爐架的熱部件。
帶供電的爐具必須接地。
請勿隨便更動本爐具的內部組件。如有
必要，請電話聯繫我們的技術支援服務
部。
安裝前
根據燃氣爐具EN 30-1-1規例，本電器為
3類置入式爐具。使用接駁配件，這些
個別爐具可與同類其他爐具結合及/或
同類普通爐架結合使用,詳見產品目錄
介紹。
爐具旁邊的器具必須用非易燃物材料
製成。分層蓋及粘接膠水必須防熱。
本爐具不可裝於冰箱、洗衣機、洗碗機
或類似電器之上。焗爐必須有一臺強力
冷卻風機以在其上面安裝本爐具。
檢查安裝說明書上焗爐的尺寸。
若裝有抽風機，必須遵守安裝手冊指
引，經常保持離爐架650mm的最小距
離。
廚房裝置的準備(圖 1-2)
在工作枱面上作出合適尺碼的切口。
如爐架使用電或氣電混合且下面并無
焗爐，在離爐架底10mm處放用非易燃
分隔件（即金屬或夾板）。此舉可防止
觸及爐架基座。
如用氣體爐，建議將分隔件置於相同距
離。
在木質工作枱面用特種膠將切口拋
光。此舉可保護枱面免受潮，因潮濕會
在工作枱面下積聚。
爐具的安裝
夾子及黏貼密封（在爐架下側）乃出廠
時配置。任何情況下均勿將它們移除。
密封確保整個工作枱面成為防水式，并
防止水滲泄。
為將爐具裝進廚櫃裝置，首先將爐具放
在正確的位置，然後鬆開每只夾子令其
均可自由轉動（不必完全鬆開它們）。
放入爐具并將其置中。
操作氣壓為
2300)
或 Elitre
。
(型號 EL-125)
Installation of appliance
(fig. 3)
使用認可印有機電工程署批准標記 (例
如 : 機電工程署批准 EMSD
APPROVAL GTXXXX) 的氣體接駁喉
管連接爐具，或使用機電工程署接納
的其他恰當方法。
(圖 3)
按下爐具側邊直到其整個周邊得到支
承。
轉動夾子并完全收緊它們。
爐具拆除
關上爐具的供電和供氣。
鬆開夾子的螺絲并按安裝之相反步驟
進行。
供氣接駁
有1/2”螺紋供：
- 固定接駁。
- 用撓性金屬管接駁。
此時須在歧管出口和供氣之
間插入配件(427950) 及水密封
件(034308)。
此時，須防止管子接觸插入的
廚櫃裝置動件（如抽屜），并防
止接觸可能變為受堵塞的任何地
方。
若要水平接駁供氣，我們的
技術支援服務處可提供直角管
(編碼 173018)及密封件（編碼
034308）
警告! 進行任何接駁時均須檢查密封
件。
泄漏的危險
接駁處理後製造商不承擔任何接
駁泄漏的責任。
供電接駁(圖 4)
檢查確保爐具的電壓及功率
與供電裝置的相匹配。
隨爐提供一條供電電纜，連
同或不帶墻裝插座插頭。
提供一隻最小接觸分離3mm 的單極切
斷開關（如用戶接觸它，插頭連接除
外）。
帶插頭的爐具只可駁至正確安裝接地
線的插座。
此爐具為“Y”型供電，電纜只能由技術
支援服務處而非用戶更改。電纜的種類
及最小橫切面必須遵從。
Cod. 9000871597 D
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
