Panasonic ESTLVK6 取扱説明書

Operating Instructions

(Household)

AC/Rechargeable Shaver

Model No.

ES-TLVK6

English �� 3

简体中文 �� 23

繁體中文 �� 43

한글 �� 61

ES-TLVK6_ASIA.indb 1 2015/06/08 13:23:02

2

ES-TLVK6_ASIA.indb 2 2015/06/08 13:23:02

3

English

Operating Instructions

(Household)

AC/Rechargeable Shaver

Model No.

ES-TLVK6

Thank you for purchasing this Panasonic product.

Before operating this unit, please read these instructions completely and save them for future use.

Safety precautions..................... 4

Intended use ��8

Parts identication ��9

Charge ��10

Using the shaver�� 11

Clean �� 13

Troubleshooting ��18

Battery life ��21

Removing the built-in rechargeable

battery��22

Specications ��22

Contents

ES-TLVK6_ASIA.indb 3 2015/06/08 13:23:02

4

English

Safety precautions

To reduce the risk of injury, loss of life, electric shock, ﬁre,

malfunction, and damage to equipment or property, always

observe the following safety precautions.

Explanation of symbols

The following symbols are used to classify and describe the level

of hazard, injury, and property damage caused when the

denotation is disregarded and improper use is performed.

DANGER

Denotes a potential

hazard that will result in

serious injury or death.

WARNING

Denotes a potential

hazard that could result

in serious injury or death.

CAUTION

Denotes a hazard that

could result in minor

injury.

The following symbols are used to classify and describe the type

of instructions to be observed.

This symbol is used to alert users to a speciﬁc operating

procedure that must not be performed.

This symbol is used to alert users to a speciﬁc operating

procedure that must be followed in order to operate the

unit safely.

WARNING

Always unplug the AC adaptor from a household

outlet when cleaning.

- Failure to do so may cause electric shock or injury.

Always ensure the appliance is operated on an

electric power source matched to the rated voltage

indicated on the AC adaptor.

Fully insert the power plug.

- Failure to do so may cause ﬁre or electric shock.

Regularly clean the power plug and the appliance

plug to prevent dust from accumulating.

- Failure to do so may cause ﬁre due to insulation failure

caused by humidity.

Disconnect the adaptor and wipe with a dry cloth.

Immediately stop using and remove the adaptor if

there is an abnormality or failure.

- Using it in such conditions may cause ﬁre, electric shock,

or injury.

• The main unit, self-cleaning recharger, adaptor or

cord is deformed or abnormally hot.

• The main unit, self-cleaning recharger, adaptor or

cord smells of burning.

• There is abnormal sound during use or charging of

the main unit, self-cleaning recharger, adaptor or

cord.

- Immediately request inspection or repair at an authorized

service center.

ES-TLVK6_ASIA.indb 4 2015/06/08 13:23:02

5

English

WARNING

If detergent contacts skin, wash immediately and

thoroughly with soap.

If you experience skin irritation anywhere on the

body, stop using immediately and contact a

physician.

- Failure to follow these instructions may result in physical

injury or injury to the skin.

If detergent or oil is consumed accidentally, do not

induce vomiting, drink a large amount of water and

contact a physician.

If detergent or oil comes into contact with eyes,

wash immediately and thoroughly with running

water and contact a physician.

- Failure to follow these instructions may result in physical

problems.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

Children should be supervised to ensure that they

do not play with the appliance.

- Failure to do so may cause an accident or injury.

The supply cord cannot be replaced. If the cord is

damaged, the AC adaptor should be scrapped.

- Failure to do so may cause an accident or injury.

This shaver has a built-in rechargeable battery. Do

not throw into ﬁre, apply heat, or charge, use, or

leave in a high temperature environment.

- Doing so may cause overheating, ignition, or explosion.

Do not connect or disconnect the adaptor to a

household outlet with a wet hand.

- Doing so may cause electric shock or injury.

Do not immerse the AC adaptor and the self-

cleaning recharger in water or wash with water.

- Doing so may cause electric shock or ﬁre due to a short

circuit.

Never use the AC adaptor and the self-cleaning

recharger in the bathroom or shower room.

- Doing so may cause electric shock or ﬁre due to a short

circuit.

Never disassemble except when disposing of the

product.

- Doing so may cause ﬁre, electric shock, or injury.

Do not use anything other than the supplied AC

adaptor and the self-cleaning recharger. Also, do

not charge any other product with the supplied AC

adaptor and the self-cleaning recharger.

- Doing so may cause burn or ﬁre due to a short circuit.

Do not modify or repair.

- Doing so may cause ﬁre, electric shock, or injury.

Contact an authorized service center for repair (battery

change etc).

Persons using an implanted medical electronic

device, such as a pacemaker, should not allow this

unit to touch the skin where the medical electronic

device is implanted.

- Doing so may cause an accident or illness.

ES-TLVK6_ASIA.indb 5 2015/06/08 13:23:02

6

English

WARNING

Do not store within reach of children or infants. Do

not let them use it.

- Putting the inner blades and/or the cleaning brush in the

mouth or drinking the oil or detergent may cause

accidents and injury.

Never use the appliance if the AC adaptor is

damaged or if the power plug ﬁts loosely in a

household outlet.

- Doing so may cause electric shock or ﬁre due to a short

circuit.

Do not damage, modify, or forcibly bend, pull, or

twist the cord.

Also, do not place anything heavy on or pinch the

cord.

- Doing so may cause electric shock or ﬁre due to a short

circuit.

Do not use in a way exceeding the rating of the

household outlet or the wiring.

- Exceeding the rating by connecting too many plugs to one

household outlet may cause ﬁre due to overheating.

Do not shave with soap or clean it with water when

operating with the AC adaptor.

- Doing so may cause electric shock or ﬁre due to a short

circuit.

CAUTION

Disconnect the adaptor from the household outlet

when not using.

- Failure to do so may cause electric shock or ﬁre due to

electrical leakage resulting from insulation deterioration.

Check the system outer foil for cracks or

deformations before use.

- Failure to do so may cause injury to the skin.

Be sure to place the protective cap on the shaver

when carrying around or storing.

- Failure to do so may cause injury to skin or reduce the life

of the system outer foil.

Disconnect the adaptor or the appliance plug by

holding onto the adaptor or the appliance plug

instead of the cord.

- Failure to do so may cause electric shock or injury.

Use caution when opening detergent as spout is

sharp.

- Failure to do so may cause injury.

Do not allow pins or trash to adhere to the power

plug or the appliance plug.

- Doing so may cause electric shock or ﬁre due to a short

circuit.

Do not use excessive pressure to apply the system

outer foil to your lip or other part of your face. Do

not apply the system outer foil directly to blemishes

or injured skin.

- Doing so may cause injury to the skin.

ES-TLVK6_ASIA.indb 6 2015/06/08 13:23:03

7

English

CAUTION

Do not forcefully press the system outer foil. Also,

do not touch the system outer foil with ﬁngers or

nails when in use.

- Doing so may cause injury to skin or reduce the life of the

system outer foil.

Do not touch the blade section (metallic section) of

the inner blade.

- Doing so may cause injury to your hands.

Do not use this product for hair on head or any

other part of the body.

- Doing so may cause injury to skin or reduce the life of the

system outer foil.

Do not share your shaver with your family or other

people.

- Doing so may result in infection or inﬂammation.

Do not remove the shaver from the self-cleaning

recharger while using the “Clean/Dry/Charge” mode

or “Dry/Charge” mode.

- Doing so may cause burn due to high temperatures

around the blades.

Do not drop or subject to shock.

- Doing so may cause injury.

Do not wrap the cord around the adaptor when storing.

- Doing so may cause the wire in the cord to break with the

load, and may cause ﬁre due to a short circuit.

Do not use detergent for any purpose other than

washing the shaver blades.

- Using it with other products may cause discoloration or

cracking.

►Disposing of the rechargeable battery

DANGER

The rechargeable battery is exclusively for use with

this shaver. Do not use the battery with other

products.

Do not charge the battery after it has been removed

from the product.

• Do not throw into ﬁre or apply heat.

• Do not hit, disassemble, modify, or puncture with a

nail.

• Do not let the positive and negative terminals of

the battery get in contact with each other through

metallic objects.

• Do not carry or store the battery together with

metallic jewelry such as necklaces and hairpins.

• Do not charge, use, or leave the battery where it

will be exposed to high temperatures, such as

under direct sunlight or near other sources of heat.

• Never peel off the tube.

- Doing so may cause overheating, ignition, or explosion.

WARNING

After removing the rechargeable battery, do not

keep it within reach of children and infants.

- The battery will harm the body if accidentally swallowed.

If this happens, consult a physician immediately.

ES-TLVK6_ASIA.indb 7 2015/06/08 13:23:03

8

English

WARNING

If the battery ﬂuid leaks out, take the following

procedures. Do not touch the battery with your bare

hands.

- The battery ﬂuid may cause blindness if it comes in

contact with your eyes.

Do not rub your eyes. Wash immediately with clean water

and consult a physician.

- The battery ﬂuid may cause inﬂammation or injury if it

comes in contact with the skin or clothes.

Wash it off thoroughly with clean water and consult a

physician.

Intended use

• Keep both the inner blades inserted. If only one of the inner

blades is inserted, the shaver may be damaged.

• If you clean the shaver with water, do not use salt water or hot

water. Do not soak the shaver in water for a long period of time.

• Clean the housing only with a soft cloth slightly dampened with

tap water or soapy tap water. Do not use thinner, benzine,

alcohol or other chemicals.

• Store the shaver in a place with low humidity after use.

• Do not store the shaver or detergent where it will be exposed to

direct sunlight or other heat sources.

• The self-cleaning recharger cleans the inner blades and the

system outer foil. Brush or wash with water to remove beard

trimmings in other areas.

• Depending on the environment, the shaver may not dry even if

you select a mode that includes the “Dry” function. In this case,

wipe off any drops of water with a dry cloth.

ES-TLVK6_ASIA.indb 8 2015/06/08 13:23:03

9

English

Parts identiﬁcation































a

c

d

b

e

f



















Front

Back

















  





A Main body

1 Protective cap

2 System outer foil

3 Foil frame

4 Foil frame release buttons

5 Finger rest

6 Power switch

7 Lock ring

8 Lamp display

a. Used time lamp

b. Battery capacity lamp

c. Shaving sensor lamp

( )

d. Clean lamp

e. Foil/blade check lamp

f. Charge status lamp

( )

9 Appliance socket

 Outer foil section

 System outer foil release

buttons

 Inner blades

 Trimmer

 Trimmer handle

 Main body rear terminals

B Self-cleaning recharger

 Charging terminals

 Cleaning liquid unit

removal button

 Intake port

 Self-cleaning recharger

socket

 Lock release lever

 Cleaning liquid ﬁlter

 Water maximum line

 Cleaning liquid unit

 STATUS lamp

 LOW lamp

 CLEAN lamp

 DRY lamp

 SELECT button

C AC adaptor (RE7-59)

 Adaptor

 Power plug

 Cord

 Appliance plug

Accessories

D Travel case

E Cleaning brush

F Oil

G Special detergent

(Detergent)

ES-TLVK6_ASIA.indb 9 2015/06/08 13:23:03

10

English

Using the lock ring

Use the lock ring to lock or unlock the power switch.

Rotate the lock ring until it clicks.

Rotate the lock ring to “ ” to unlock the power

switch:

Used when shaving, washing the shaver, lubricating

the shaver.

Rotate the lock ring to “ ” to lock the power

switch:

Used when carrying the shaver.

Charge

Charging using the self-cleaning recharger

Thoroughly wipe off any drops of water on or around the self-

cleaning recharger so that it is dry before charging the shaver.

1

Insert the appliance plug into

the self-cleaning recharger.

2

Remove the protective cap

and then attach the shaver.

• Turn the shaver off before attaching.

• Wipe off any water droplets on the

main body rear terminals.

1

2

3

• Check that the outer foil is not deformed or damaged when

you are attaching the shaver.

3

Plug in the adaptor into a household outlet.

• The “Charge” mode starts when attaching the shaver.

• Check that the charge status lamp ( ) glows.

• Charging is completed after approx. 1 hour.

The charging time may decrease depending on the

charging capacity.

While charging After charging is completed

The charge status lamp ( )

glows.

The number of the battery

capacity lamp will increase as

charging progresses.

The battery capacity lamp and

the charge status lamp will

light up and then turn off after

5 seconds.

Abnormal charging

The charge status lamp ( ) will blink twice every second.

• Recommended ambient temperature for charging is 10 – 35 °C.

It may take longer to charge or the battery may fail to charge

properly in extremely high or low temperatures.

Charge the shaver within the recommended ambient temperature

range.

• When charging the shaver for the ﬁrst time or when it has not

been in use for more than 6 months, the charge status lamp (

)

may not glow. It will eventually glow if kept connected.

4

Disconnect the adaptor after charging is

completed.

• You can charge even with the STATUS lamp of the self-cleaning

recharger glowing.

• The appliance can be charged even with the cleaning liquid unit

removed.

ES-TLVK6_ASIA.indb 10 2015/06/08 13:23:03

11

English

Charging without the self-cleaning recharger

You can also charge without the self-cleaning recharger.

1

Insert the appliance plug into

the shaver.

• Turn the shaver off before inserting.

2

Plug in the adaptor into a

household outlet.

• Wipe off any water droplets on the

appliance socket.

1

2

3

Disconnect the adaptor after charging is

completed.

Using the shaver

1

Rotate the lock ring to unlock the power switch.

(See page 10.)

2

Press the power switch to select the desired

shaving mode.

• Each time you press the power switch, the shaving mode

changes from “Shaving sensor mode” “Normal mode”

“OFF”.

Shaving

mode

Shaving sensor

mode

Normal mode OFF

Description

Beard thickness

is automatically

sensed and the

power is

automatically

adjusted when

shaving.

The power level

is constantly

maintained

while shaving.

—

Operation

Shaving

sensor lamp

The shaving

sensor lamp

blinks.

—

The shaving

sensor lamp

turns off.

—

The shaving

sensor lamp

turns off.

• The shaving sensor may not respond when the remaining

battery capacity is low. If this happens, recharge the shaver.

ES-TLVK6_ASIA.indb 11 2015/06/08 13:23:03

12

English

3

Hold the shaver as illustrated

and shave.

• Start shaving by applying gentle

pressure to your face. Stretch your

skin with your free hand and move the

shaver back and forth in the direction

of your beard. You may gently increase

the amount of pressure as your skin

becomes accustomed to this shaver.

Applying excessive pressure does not

provide a closer shave.

►Cord shaving

If you insert the appliance plug to the shaver and plug in the

adaptor into a household outlet, you can use it even if the battery

capacity is low.

• If the shaver does not work, continue charging it for approx.

1 minute.

►Switching the shaver head

You can change the pivot action.

FREE

You can move the shaver head.

LOCK

You can lock the shaver head.

►Using the trimmer

Slide the trimmer handle up to the “ ”

position so that the trimmer stands upright.

Press and hold the lock release

button (a) and slide the trimmer

handle down to lower the trimmer.



Trimming sideburns

Slide the trimmer handle up. Turn the shaver

on and place at a right angle to your skin

and move downwards to trim your

sideburns.

Pre-shave

The trimmer can be used for a

pre-shave of long beards.

ES-TLVK6_ASIA.indb 12 2015/06/08 13:23:04

13

English

►Notes

• If you press the power switch for more than 2 seconds, the sonic

vibration cleaning mode is activated. (See page 15.)

You cannot shave in this mode.

• Do not place your ﬁngers on the power switch while using the

shaver. This may cause the shaver to switch the mode or turn off.

Place your ﬁngers on the ﬁnger rest while using the shaver.

• We recommend using the shaver in an ambient temperature range of

5 – 35 °C. If used outside this range, the appliance may stop operating.

Reading lamps when using

During use After use

The used time and remaining

battery capacity are shown and

then turn off after 5 seconds.

• The shown time returns to

[0’00”] after 10 minutes.

• The charge status lamp ( )

glows when using cord shaving.

The lamps will light up and

then turn off after 8 seconds.

When the battery capacity is low

“10%” appears and “

” blinks.

• You can shave 1 to 2 times after “10%” appears. (This will differ

depending on usage.)

• A full charge will supply enough power for approx. 14 shaves of

3 minutes each. (This will differ depending on usage.)

Clean

Cleaning using the self-cleaning recharger

►Preparing the self-cleaning recharger

Remove the shaver and the appliance plug from the self-cleaning

recharger.

1

Place the self-cleaning recharger on a hard, ﬂat

surface.

• When the self-cleaning recharger is lifted, or on the soft

surface such as carpets, the lock release lever will not ﬁt in

the recharger properly. In that case, the cleaning liquid unit

cannot be removed.

2

Press the cleaning

liquid unit removal

button and remove

the cleaning liquid

unit.

1

2

3

Wash away the old cleaning liquid and beard

trimmings and then rinse the cleaning liquid unit.

• After washing, be sure to attach the cleaning liquid ﬁlter.

4

Pour tap water and

detergent into the

cleaning liquid unit.

• Do not let the water rise

above the maximum water

line. This may cause the

cleaning liquid to spill.

21

ES-TLVK6_ASIA.indb 13 2015/06/08 13:23:04

14

English

5

Attach the cleaning liquid unit.

• Immediately wipe up any cleaning liquid

that has been spilt.

Be careful not to drop cleaning liquid

onto leather products or wooden ﬂoors

as it may cause discoloration.

6

Press the top of the self-

cleaning recharger down and

securely attach until it clicks.

►Notes

• The water and detergent will mix after cleaning begins, making

cleaning liquid.

• When the cleaning liquid level has dropped, the LOW lamp will

glow to indicate the cleaning liquid should be replaced.

• After the LOW lamp glows, you can clean the shaver with the

self-cleaning recharger for approximately 7 days.

• Replace the cleaning liquid when the STATUS lamp glows.

• When replaced, the cleaning liquid will last for approximately

30 days if used once per day. (This will differ depending on beard

thickness and the ambient temperature.)

• Use the detergent within approximately 6 months after opening

the package. When 6 months have passed, discard the cleaning

liquid, and then pour new water and detergent into the cleaning

liquid unit.

• Replace the water and detergent at the same time.

Otherwise the cleaning function may deteriorate.

• Only use self-cleaning recharger detergent for Panasonic shavers.

►Cleaning the shaver

Remove any soap or water on the shaver if it has been washed

with hand soap or any other detergent.

1

Insert the appliance plug

into the self-cleaning

recharger.

2

Remove the protective cap

and then attach the shaver.

3

Plug in the adaptor into a

household outlet.

1

2

3

• Turn the shaver off before attaching.

• Wipe off any water droplets on the main body rear terminals.

• Check that the outer foil is not deformed or damaged when you

are attaching the shaver.

4

Press the SELECT button to select the mode.

• The “Charge” mode starts when attaching the shaver.

• Each time you press the SELECT button, the mode changes

from “Clean/Dry/Charge” “Dry/Charge” “Charge”.

• The modes start approximately 6 seconds after they are

selected.

• The mode will be aborted if the power is cut off. In this case,

perform the mode again from the beginning.

• Do not press the cleaning liquid unit removal button as the

cleaning liquid may spill causing a malfunction.

ES-TLVK6_ASIA.indb 14 2015/06/08 13:23:04

15

English

Mode Time required (guide)

1 Charge

Charge

0 to 60 min

2 Clean/Dry/

Charge

Clean

10 min

Dry

80 min

(170 min*)

Charge

0 to 60 min

• It is not possible to change the mode after the

“Clean/Dry/Charge” mode has started.

3 Dry/Charge

Dry

180 min

Charge

0 to 60 min

• It is possible to change to the “Clean/Dry/

Charge” mode even after the “Dry/Charge”

mode has started.

* When the ambient temperature of the self-cleaning recharger is

low (approx. 15 °C or lower), the time it takes to dry the shaver

increases.

• Use the self-cleaning recharger in temperatures between 15 °C

and 35 °C.

• The Clean or Dry function may stop under extreme low

temperatures (approx. 0 °C or lower). In such a case, the

STATUS lamp will glow for approximately 5 seconds and the

mode will switch to the “Charge” mode without allowing you to

select the “Clean/Dry/Charge” mode or the “Dry/Charge” mode.

Cleaning the shaver without the self-cleaning recharger

We recommend that you clean your shaver with the self-cleaning

recharger or the sonic vibration cleaning mode when the faucet

symbol appears on the lamp display.

1. Disconnect the cord from the shaver.

2. Apply some hand soap and some

water to the system outer foil.

3. Rotate the lock ring to unlock the

power switch.

4. Press the power switch for more than 2

seconds to activate the sonic vibration

cleaning mode.

• The battery capacity lamps blink in

order.

• After about 20 seconds, it will be

automatically turned off, or you can

turn it off by pressing the power

switch.

5. Remove the outer foil section and

press the power switch for more than

2 seconds to activate the sonic

vibration cleaning mode and clean it

with running water.

6. Wipe off any drops of water with a dry

cloth.

7. Dry the outer foil section and the

shaver completely.

8. Attach the outer foil section to the

shaver.

9. Lubricate the shaver.

4

5

7

The mark on the left means suitable for cleaning

under an open water tap.

ES-TLVK6_ASIA.indb 15 2015/06/08 13:23:05

16

English

Warning

Disconnect the cord from the shaver before cleaning it in

water to prevent electric shock.

►Drying the shaver with the self-cleaning recharger

1. Attach the outer foil section to the shaver.

2. Dry the shaver with self-cleaning recharger using “Dry/Charge”

mode.

3. Lubricate the shaver.

Lubrication

To maintain shaving comfort for a long time, it is recommended

that the oil provided with the shaver is used.

1. Switch off the shaver.

2. Apply one drop of oil to each of the

outer foils.

3. Raise the trimmer and apply a drop

of oil.

4. Switch the shaver on, and run it for

approximately ﬁve seconds.

32

5. Switch off the shaver, and wipe off any excess oil from the outer

foils with a soft cloth.

Cleaning with the brush

►Cleaning with the long brush

Clean the system outer foil

(a), the shaver body (b) and

the trimmer (c) using the

long brush.

  

►Cleaning with the short brush

Clean the inner blades using the short brush by

moving it in direction (A).

• Do not move the short brush in direction (B) as

it will damage the inner blades and affect their

sharpness.

• Do not use the short brush to clean the outer

foils.

(A)

(B)

Replacing the system outer foil and the inner blades

appears on the lamp display once a year. (This will differ

depending on usage.) We recommend checking the system outer

foil and the inner blades when it appears.

Press the power switch for more than 30 seconds to turn off .

system outer foil once every year

inner blades once every two years

►Removing the outer foil section

Press the foil frame release buttons and lift the

outer foil section upwards.

►Attaching the outer foil section

After turning the foil frame mark ( ) to the front,

securely attach the outer foil section to the shaver

until it clicks.

ES-TLVK6_ASIA.indb 16 2015/06/08 13:23:05

17

English

►Replacing the system outer foil

1. Press the system outer foil release buttons

and pull down the system outer foil.

2. Align the foil frame mark ( ) and the

system outer foil mark ( ) and securely

attach together.

• The system outer foil cannot be reversely

attached.

• Always insert the system outer foil to the

foil frame when attaching to the shaver.

2

1

►Replacing the inner blades

1. Remove the inner blades one at a time.

• Do not touch the edges (metal parts) of the

inner blades to prevent injury to your hand.

2. Insert the inner blades one at a time until they

click.

21

►Replacement parts

Replacement parts are available at your dealer or Service Center.

Replacement parts for

ES-TLVK6

System outer foil WES9173

Inner blades WES9170

Special Detergent for Shaver Cleaning & Charging

System

WES4L03

Cleaning the self-cleaning recharger

Beard trimmings may become attached to the cleaning tray of the

self-cleaning recharger. Follow the steps below to remove them.

We recommend doing this each time you change the cleaning

liquid.

1. Be sure to remove the cleaning liquid unit

and the appliance plug from the self-

cleaning recharger.

• Be careful not to spill the cleaning liquid.

• Some cleaning liquid components and

skin oil may separate and adhere to the

cleaning liquid unit and cleaning liquid

ﬁlter. This does not indicate a problem.

2. Pour water as illustrated while

tilting the cleaning liquid unit

and shaking it gently.

• You can clean with the

cleaning liquid ﬁlter removed.

• After washing, be sure to

attach the cleaning liquid

ﬁlter.

3. Gently wipe off any beard trimmings

attached to the inside of the cleaning tray

with a cloth or tissue paper dampened with

water.

• Clean the corners and uneven parts of the

cleaning tray with a cotton swab

dampened with water.

ES-TLVK6_ASIA.indb 17 2015/06/08 13:23:05

18

English

►When the water does not drain from the cleaning

tray

Beard trimmings may clog the drain at the

bottom of the cleaning tray.

In this case, you cannot clean or dry the shaver.

Push the beard trimmings down through the

drain with a toothpick etc.

Troubleshooting

►Self-cleaning recharger

Problem Action

The blade has not been

thoroughly washed.

If the shaver is not cleaned for

more than 2 weeks, ﬁrst clean

with the cleaning brush to remove

beard trimmings. (See page 16.)

Do not add detergent and water

except when replacing the

cleaning liquid.

Doing so may deteriorate the

cleaning function. (See page 14.)

After cleaning, oil-like droplets

may remain on the outside of the

foil frame. This is the lubricating

component of the cleaning liquid

and does not indicate a problem.

You may wipe it off with a soft

cloth.

The STATUS lamp glows.

See page 21.

Problem Action

The mode does not start.

Check that the AC adaptor is

connected to the self-cleaning

recharger, and that the recharger

is plugged in to a household

outlet. (See page 10.)

Conﬁrm that the shaver is

properly attached to the self-

cleaning recharger.

(See page 10.)

The Clean or Dry operation may

not function under extreme low

temperatures (approx. 0 °C or

lower).

Check if the STATUS lamp glows.

(See page 21.)

Cleaning liquid has

accumulated in the

cleaning tray.

Remove any waste, etc. that has

accumulated in the drain at the

bottom of the cleaning tray.

(See this page.)

If you use the self-cleaning

recharger when the shaver is wet

or when soap or shaving gel is on

the shaver, cleaning liquid may

accumulate in the cleaning tray.

The cleaning liquid unit

cannot be removed.

Place the self-cleaning recharger

on a hard, ﬂat surface.

When the self-cleaning recharger

is lifted, or on the soft surface such

as carpets, the lock release lever

will not ﬁt in the recharger properly.

In that case, the cleaning liquid

unit cannot be removed.

ES-TLVK6_ASIA.indb 18 2015/06/08 13:23:05

19

English

Problem Action

Makes a loud sound.

During cleaning:

The self-cleaning recharger

makes a loud sound due to the

cleaning of the blades.

After cleaning:

The self-cleaning recharger

makes a loud sound due to the

removal of water droplets in

order to speed drying.

The sound after cleaning is

different from the sound during

cleaning. The water level has

dropped and it is removing water

droplets from the blades after

cleaning. This does not indicate a

problem.

The shaver cannot be

charged.

Gently wipe the main body rear

terminals and the charging

terminals of the self-cleaning

recharger with a cloth or tissue

dampened with water.

The blades are not dry or

are sticky.

The blades may not dry quickly

due to temperature conditions.

Run the “Dry/Charge” mode again

or wipe with a soft cloth before

shaving.

The blades crack or

deform during cleaning.

Do not insert any foreign objects

into the recharger.

Replace the system outer foil and/

or inner blades. (See page 16.)

Problem Action

The cleaning liquid has

foamed.

If you mix soapy water or hand

soap with the detergent or use

another detergent, the cleaning

liquid will foam. Use the self-

cleaning recharger after thoroughly

washing and drying the shaver.

Replace the cleaning liquid.

Cleaning liquid leaked

from the cleaning liquid

unit.

Do not press the cleaning liquid unit

removal button during the mode.

Place the self-cleaning recharger

horizontally.

If you use the self-cleaning

recharger when the shaver is wet

or when soap or shaving gel is on

the shaver, cleaning liquid may

leak.

►Shaver

Problem Action

Trimmed hairs ﬂy all over.

This can be improved by cleaning

every time after shaving.

Clean the inner blades with the

brush.

Apply oil after cleaning with water

and leaving to dry thoroughly.

System outer foil gets hot.

Apply oil.

(See page 16.)

Replace the system outer foil if it

is damaged or deformed.

(See page 17.)

ES-TLVK6_ASIA.indb 19 2015/06/08 13:23:06

20

English

Problem Action

The power switch cannot

be pressed.

Unlock the power switch.

Operating time is short

even after charging.

Apply oil.

When the number of operations

per charge starts to decrease, the

battery is nearing the end of its life.

Makes a loud sound.

Apply oil.

Conﬁrm that the blades are

properly attached.

The shaver makes a high-pitched

sound due to the linear motor

drive. This does not indicate a

problem.

Clean the system outer foil with

the brush.

The odor is getting

stronger.

This can be improved by cleaning

every time after shaving.

You do not get as close a

shave as before.

This can be improved by cleaning

every time after shaving.

Replace the system outer foil and/

or inner blades.

Expected life of system outer foil

and inner blades:

System outer foil:

Approximately 1 year

Inner blades:

Approximately 2 years

Apply oil.

Problem Action

The shaving sensor does

not respond.

The shaving sensor may not

respond when the remaining

battery capacity is low. If this

happens, recharge the shaver.

Depending on the beard

thickness, the shaving sensor

may not react and the driving

sound may not change. This is not

abnormal.

Apply oil. The shaving sensor may

not respond when there is not

enough oil on the blades.

The shaving sensor

responds even though the

shaver is not in contact

with the skin.

Clean the beard trimmings from

the shaver.

When the shaver is extremely

dirty, remove the foil frame and

wash with water.

(See page 15.)

Replace the system outer foil and/

or inner blades.

Expected life of system outer foil

and inner blades:

System outer foil:

Approximately 1 year

Inner blades:

Approximately 2 years

The shaver cannot be

charged with the self-

cleaning recharger.

Gently wipe the main body rear

terminals and the charging

terminals of the self-cleaning

recharger with a cloth or tissue

dampened with water.

ES-TLVK6_ASIA.indb 20 2015/06/08 13:23:06

ページが読み込まれています...

Panasonic ESTLVK6 取扱説明書

Panasonic ESTLVK6 取扱説明書

他の言語で

関連論文

その他のドキュメント