Operating Instructions
(Household) Rechargeable Shaver
Model No.
ES‑BST6Q
ES‑BST2Q
English ��������������������������������������������� 3
中文 ������������������������������������������������ 21
한글 ������������������������������������������������ 37
�������������������������������������������������� 55
2
3
English
Operating Instructions
(Household) Rechargeable Shaver
Model No.
ES‑BST6Q
ES‑BST2Q
Thank you for purchasing this Panasonic product.
Before operating this unit, please read these instructions completely and save them for future use�
Safety precautions..................... 4
Intended use ����������������������������������������8
Parts identication ������������������������������8
Before use ��������������������������������������������9
Charging the shaver �������������������������� 10
How to use ����������������������������������������� 11
Cleaning the shaver ��������������������������14
Replacing the system outer foil and
the inner blades ���������������������������������16
FAQ �����������������������������������������������������17
Troubleshooting ��������������������������������17
Battery life ������������������������������������������19
Removing the built-in rechargeable
battery�������������������������������������������������20
Specications ������������������������������������20
Contents
4
English
Safety precautions
To reduce the risk of injury, loss of life, electric shock, re, and
damage to property, always observe the following safety precautions.
Explanation of symbols
The following symbols are used to classify and describe the level
of hazard, injury, and property damage caused when the
denotation is disregarded and improper use is performed.
DANGER Denotes a potential
hazard that will result in
serious injury or death.
WARNING Denotes a potential
hazard that could result in
serious injury or death.
CAUTION Denotes a hazard that
could result in minor injury
or property damage.
The following symbols are used to classify and describe the type
of instructions to be observed.
This symbol is used to alert users to a specic operating
procedure that must not be performed.
This symbol is used to alert users to a specic operating
procedure that must be followed in order to operate the
unit safely.
WARNING
►This product
This shaver has a built-in rechargeable battery� Do
not throw into re, apply heat, or charge, use, or
leave in a high temperature environment�
‑ Doing so may cause overheating, ignition, or explosion.
Do not modify or repair�
‑ Doing so may cause re, electric shock, or injury.
Contact an authorized service center for repair (battery
change etc).
Never disassemble except when disposing of the
product�
‑ Doing so may cause re, electric shock, or injury.
►In case of an abnormality or malfunction
Immediately stop using and remove the adaptor if
there is an abnormality or malfunction�
‑ Failure to do so may cause re, electric shock, or injury.
<Abnormality or malfunction cases>
•The main unit, charging stand, adaptor or cord is
deformed or abnormally hot�
•The main unit, charging stand, adaptor or cord
smells of burning�
•There is an abnormal sound during use or
charging of the main unit, charging stand, adaptor
or cord�
‑ Immediately request inspection or repair at an authorized
service center.
5
English
WARNING
►Power supply
Do not connect or disconnect the adaptor to a
household outlet with a wet hand�
‑ Doing so may cause electric shock or injury.
Do not immerse the AC adaptor and the charging
stand in water or wash with water�
Do not place the AC adaptor and the charging stand
over or near water lled sink or bathtub.
Never use the appliance if the AC adaptor is
damaged or if the power plug ts loosely in a
household outlet�
Do not damage, modify, or forcibly bend, pull, or
twist the cord� Also, do not place anything heavy on
or pinch the cord�
‑
Doing so may cause electric shock or re due to a short circuit.
Do not use in a way exceeding the rating of the
household outlet or the wiring�
‑ Exceeding the rating by connecting too many plugs to one
household outlet may cause re due to overheating.
Do not use anything other than the supplied AC
adaptor and the charging stand for any purpose�
Also, do not use any other product with the supplied
AC adaptor and the charging stand� (See page 9�)
‑ Doing so may cause burn or re due to a short circuit.
Always ensure the appliance is operated on an
electric power source matched to the rated voltage
indicated on the AC adaptor�
Fully insert the adaptor�
‑ Failure to do so may cause re or electric shock.
Disconnect the AC adaptor when cleaning the
shaver with water�
‑ Failure to do so may cause electric shock or injury.
Regularly clean the power plug, the appliance plug and
the charging plug to prevent dust from accumulating�
‑ Failure to do so may cause re due to insulation failure
caused by humidity.
►Preventing accidents
Do not place within reach of children or infants� Do
not let them use it�
‑ Putting parts or accessories in the mouth may cause an
accident or injury.
If oil is consumed accidentally, do not induce
vomiting, drink a large amount of water and contact
a physician�
If oil comes into contact with eyes, wash
immediately and thoroughly with running water and
contact a physician�
‑ Failure to follow these instructions may result in physical
problems.
►Take care of the following precautions as well
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety�
Children should be supervised to ensure that they
do not play with the appliance�
‑ Failure to do so may cause an accident or injury.
6
English
WARNING
The supply cord cannot be replaced� If the cord is
damaged, the AC adaptor should be scrapped�
‑ Failure to do so may cause an accident or injury.
CAUTION
►Protecting the skin
Do not use excessive pressure to apply the system
outer foil to your lip or other part of your face�
Do not apply the system outer foil directly to
blemishes or injured skin.
Do not touch the blade section (metallic section) of
the inner blade�
‑ Doing so may cause injury to skin or hand.
Do not forcefully press the system outer foil� Also,
do not touch the system outer foil with ngers or
nails when in use�
Do not use this product for hair on head or any
other part of the body�
‑ Doing so may cause injury to skin or reduce the life of the
system outer foil.
Check the system outer foil for cracks or
deformations before use�
‑ Failure to do so may cause injury to the skin.
Be sure to place the carrying holder on the shaver
when carrying around or storing�
‑ Failure to do so may cause injury to skin or reduce the life
of the system outer foil.
►Note the following precautions
Do not wrap the cord around the adaptor when storing�
‑ Doing so may cause the wire in the cord to break with the
load, and may cause re due to a short circuit.
Do not allow metal objects or trash to adhere to the
power plug, the appliance plug or the charging plug�
‑
Doing so may cause electric shock or re due to a short circuit.
Do not disconnect the adaptor or the appliance plug
by holding onto the cord�
‑ Doing so may cause electric shock or injury.
Do not share your shaver with your family or other
people�
‑ Doing so may result in infection or inammation.
Do not drop or hit against other objects�
‑ Doing so may cause injury.
Disconnect the adaptor from the household outlet
when not charging�
‑ Failure to do so may cause electric shock or re due to
electrical leakage resulting from insulation deterioration.
7
English
Handling of the removed battery when disposing
DANGER
•The rechargeable battery is exclusively for use with
this appliance� Do not use the battery with other
products�
•Do not charge the battery after it has been removed
from the product�
•Do not throw into re or apply heat.
•Do not hit, disassemble, modify, or puncture with a nail�
•Do not let the positive and negative terminals of
the battery get in contact with each other through
metallic objects�
•Do not carry or store the battery together with
metallic jewellery such as necklaces and hairpins.
•Do not use or leave the battery where it will be
exposed to high temperatures, such as under
direct sunlight or near other sources of heat�
•Never peel off the tube�
‑ Doing so may cause overheating, ignition, or explosion.
WARNING
After removing the rechargeable battery, do not
keep it within reach of children and infants.
‑ The battery will harm the body if accidentally swallowed.
If this happens, consult a physician immediately.
If the battery uid leaks out and comes in contact
with the eyes, do not rub the eyes, and thoroughly
rinse with clean water, such as tap water�
‑ Failure to do so may cause eye injury.
Consult a physician immediately.
CAUTION
If the battery uid leaks out and comes in contact
with the skin or clothes, rinse off with clean water,
such as tap water�
‑ Failure to do so may cause inammation.
8
English
Intended use
• This WET/DRY shaver can be used for wet shaving using
shaving lather or for dry shaving. You can use this watertight
shaver in the shower and clean with water. The following symbol
means suitable for use in a bath or shower.
►Notes
• Treat yourself to wet lather shaves for at least three weeks and
notice the difference. Your Panasonic WET/DRY shaver requires
a little time to get used to because your skin and beard need
about a month to adjust to any new shaving method.
• Do not bring the system outer foil into contact with hard objects.
Doing so may damage the blades as they are very thin and
deform easily.
• Do not dry the main unit with a dryer or a fan heater.
Doing so may cause malfunction or deformation of the parts.
• Do not leave the shaver exposed to direct sunlight with the foil
frame detached.
Doing so may deteriorate the waterproof rubber and degrade
waterproof function, which may cause to malfunction.
• Store the shaver in a place with low humidity after use.
Failure to do so may cause malfunction due to condensation or rust.
• Keep both the inner blades inserted. If only one of the inner
blades is inserted, the shaver may be damaged.
• If you clean the shaver with water, do not use salt water or hot
water. Do not soak the shaver in water for a long period of time.
• The following symbol indicates that a specic detachable power
supply unit is required for connecting the electrical appliance to
the supply mains. The type reference of power supply unit is
marked near the symbol.
Parts identication
Front Back
9
English
A Main body
1 System outer foil
2 Foil frame
3
Foil frame release buttons
4 Cleaning shutter
5 Finger rest
6 Power switch
To turn the shaver on and
off and also lock and
unlock the power switch.
7 Switch lock lamp ( )
8 Charge status lamp ( )
9 Appliance socket
: Inner blades
; Trimmer
Trimmer handle
Outer foil section
System outer foil release
buttons
Water inlet
B AC adaptor (RE7-87)
Adaptor
Power plug
Cord
Appliance plug
C Charging stand (RC9-86)
ES-BST6Q
D Charging plug
E Stand socket
Accessories
D Carrying holder
E Cleaning brush
F Oil
G Travel pouch ES-BST6Q
Before use
►Using the carrying holder
The shaver can be kept vertically. When transporting the shaver,
you can use the carrying holder to protect the outer foil.
• When transporting the shaver, be sure to clean off any shavings
before attaching the carrying holder.
►Attaching the carrying holder
Attach the carrying holder as illustrated.
• With the protrusion (a) facing the front, securely attach the
carrying holder to the shaver aligned to the orientation of the
shaver head until it clicks.
►Removing the carrying holder
Remove the carrying holder while pressing down on both sides.
10
English
Charging the shaver
• Turn the shaver off.
• Attach the carrying holder so as not to scratch the system outer foil.
• Wipe off any water droplets on the appliance socket and the
charging stand.
1
1Insert the appliance plug
into the shaver�
2
2Plug in the adaptor into a
household outlet�
• Charging is completed after
approx. 1 hour.
The charging time may differ with
the charging capacity.
1
2
3
3
Disconnect the adaptor after charging is completed�
• Charging the battery for more than 1 hour will not affect
battery performance.
Note
You cannot operate the shaver while charging.
While charging After charging is
completed
Abnormal charging
The charge status
lamp ( ) glows red.
The charge status
lamp ( ) turns off.
The charge status
lamp ( ) will blink
twice every second.
• After charging is completed, turning the power switch ON with
the shaver plugged in will cause the charge status lamp ( ) to
light up and then turn off after 5 seconds.
This shows that the shaver is fully charged.
• When charging the shaver for the rst time or when it has not
been in use for more than 6 months, the charging time may
change or the charge status lamp ( ) may not glow for a few
minutes. It will eventually glow if kept connected.
• Recommended ambient temperature for charging is
10 °C – 35 °C. It may take longer to charge or the battery may
fail to charge properly in extremely high or low temperatures.
The charge status lamp ( ) will blink twice every second when
there is a problem with charging.
Charge the shaver within the recommended ambient
temperature range.
• The shaver can be used for approximately 2 weeks with a full
charge. (Based on one 3‑minute dry‑shave usages per day in an
ambient temperature range of 20 °C – 30 °C.)
The number of usable days varies depending on the following
conditions.
‑ Beard thickness
‑ Pressure applied to the skin
‑ Usage of wet shaving
‑ Usage in shaving foam mode
• If there is noise from the radio or other sources while using or
charging the appliance, move to a different location to use the
appliance.
11
English
Charging with the charging stand ES-BST6Q
1. Insert the appliance plug into the
charging stand.
2.
Place the shaver on the charging stand.
3. Plug in the adaptor into a household
outlet.
1
2
3
How to use
►Usable facial cleansers, etc�
Shaving
Shaving
foam mode
ES-BST6Q
Shaving agent
Shaving foam —
Shaving gel
Shaving cream
Facial cleanser
Facial cleansing foam
(without scrubbing
compounds)
Facial cleansing foam
(with scrubbing
compounds)
Facial soap
Body soap etc. Liquid
Foam —
• Do not use anything other than above listed shaving agent/facial
cleanser/body soap etc. as these may cause the blades to clog,
or be unable to make foam.
12
English
Making foam ES-BST6Q
It is easier to make foam this way than by hand.
1
1Take an appropriate amount of
facial cleanser etc� in the palm
of your hand�
2
2Add an appropriate amount of
water or hot water�
3
3Hold the power switch for
2 seconds or more to switch to
shaving foam mode�
The switch lock lamp ( )
and charge status lamp ( )
blink alternately.
• The shaving foam mode ends after 15 seconds. The shaver
can then be used to shave.
• To stop using the shaving foam mode and start shaving,
press the power switch once.
• When the switch lock lamp ( ) blinks after the power switch is
pressed, the shaver will not operate as it is locked. Press the
power switch for more than 2 seconds to unlock. (See page 14.)
4
4Press the blades gently in the
palm of your hand, mix the
facial cleanser etc� around and
move the blades up and down
to make foam.
• If there is insufcient foam, add slightly
more water, hot water or facial cleanser
etc. to make it easier to create foam.
►Notes
• Before making foam, check that the blades are not broken or
deformed, and that the cleaning shutter is closed.
• Do not use shaving agent (excluding foam), facial cleansing
foam (with scrubbing compounds) or soap as these may cause
the blades to clog, or be unable to make foam.
Shaving
1
1Press and shave�
• The power cannot be turned on when the
switch lock lamp ( ) blinks, as the
power switch is locked.
Press the power switch for more than
2 seconds to unlock. (See page 14.)
13
English
Tips for better shaving
Apply the whole system outer foil
perpendicularly against the skin and
shave by slowly gliding the shaver over
the face against the grain of the beard.
• The beard under the chin and around the
throat can be shaved better by stretching
the skin so the beard will stand.
• To prevent damaging the system outer
foil, do not shave with only a part of the
system outer foil.
You can also use a pen grip to hold the
shaver.
2
2Press when nished.
When the battery capacity is low
The charge status lamp ( ) blinks once every
second when operating the shaver.
The appliance beeps twice after switched off.
• You can shave 2 to 3 times after the charge
status lamp ( ) blinks. (This will differ
depending on usage.)
►Using the trimmer
Slide the trimmer handle up. Place at a right
angle to your skin and move downwards to trim
your sideburns.
►Tips for better usage
Apply the trimmer edge perpendicular to skin gently and move
downward slowly.
Trimming sideburns Pre‑shave of long beards
►Notes
• The “shaving sensor”, which automatically adjusts the power
depending on the beard thickness, will operate.
It will shave with high power on areas where the beard is heavy,
and reduce the power on areas where the beard is thin, to
reduce burden on the skin.
• Before shaving, check that the cleaning shutter is closed.
• After wet shaving, wash the main body with water and apply oil
to the system outer foil.
• Depending on the beard thickness or the amount of beard
trimmings in the shaver head, the shaving sensor may not react
and the driving sound may not change. This is not abnormal.
• The appliance may not operate in an ambient temperature lower
than approximately 5 °C.
14
English
• The shaving sensor may not respond depending on the type and
quantity of the shaving gel or the quantity of the foam. This is not
abnormal.
• To prevent erroneous operation, place your ngers on the nger
rest while using the shaver.
Operation and display of the switch lock
►Locking the power switch
1. Press once
and then release.
• The shaver
starts operating.
2.
Press for more
than 2 seconds.
• The switch lock
lamp ( ) will
light up for
5 seconds and
turn off.
• The shaver will
stop operating.
3. Release .
►Unlocking the power switch
1. Press for more than
2 seconds.
• The switch lock lamp ( )
will turn off.
2. Once the shaver starts
operating, release .
• The power switch cannot be unlocked while charging.
• The power switch is locked when the switch lock lamp ( ) blinks
for 5 seconds and the shaver does not operate even though the
power switch is pressed.
Cleaning the shaver
We recommend cleaning the shaver after each use.
1.
Turn the shaver off and disconnect the AC adaptor.
2. Apply some hand soap and some water to the
system outer foil.
• Close the cleaning shutter.
3. Turn the shaver on.
• Hold the power switch for 2 seconds or more
to switch to shaving foam mode.
ES-BST6Q
▼
There are two ways to clean the shaver, depending on the
actual dirt level�
▼ ▼
15
English
▼ ▼
To remove light dirt To remove heavy dirt
4. Slide the cleaning shutter
until it clicks.
5. Clean the outer foil section
with running water.
6. Turn the shaver off.
• Rinse with water and
shake up and down
several times to remove
the water.
4. Turn the shaver off after
10 – 20 seconds.
5.
Remove the outer foil section
and turn the shaver on.
6. Clean the shaver and the
outer foil section with
running water.
• Rinse with water and
shake up and down
several times to remove
the water.
▼ ▼
▼ ▼
7. Wipe off any drops of water with a dry cloth.
8. Dry the outer foil section, the shaver,
and the trimmer completely.
• Allow the shaver to dry in the shade,
avoid direct sunlight.
9. Lubricate the shaver.
It will keep the movement of the blade
smooth and maintain a comfort shave.
1. Apply one drop of oil to each of the
system outer foils.
2. Raise the trimmer and apply a
drop of oil.
3. Switch the shaver on, and run it for
approximately ve seconds.
4. Switch off the shaver, and wipe off
any excess oil from the system
outer foil with a soft cloth.
►Notes
• Do not use any kitchen or bathroom detergents other than hand
soap.
Doing so may cause malfunction.
• Do not wipe with thinners, benzine, alcohol etc.
Doing so may cause malfunction, or cracking or discoloration of
the parts.
Wipe with diluted soapy water.
• Be careful not to hit the main body on the sink or any other object
while draining the water. Failure to do so may cause malfunction.
16
English
Cleaning with the brush
Remove the outer foil section and the inner blades.
(See this page.)
Do not use any brush other than the supplied one.
►Cleaning with the long brush
Clean the outer foil section, system
outer foil, the shaver body and the
trimmer using the long brush.
►Cleaning with the short brush
• Clean the inner blades using the short
brush by moving it in direction as illustrated.
• Do not move the short brush
perpendicularly against the blades as it
will damage the inner blades and affect
their sharpness.
Replacing the system outer foil and
the inner blades
system outer foil once every year
inner blades once every two years
►Removing the outer foil section
Press the foil frame release buttons and lift the
outer foil section upwards.
►Attaching the outer foil section
After turning the water inlet surface to the front,
securely attach the outer foil section to the shaver
until it clicks.
►Replacing the system outer foil
1. Press the system outer foil release buttons
and pull down the system outer foil.
• Do not press the system outer foil
release buttons with excessive force.
Doing so may bend the system outer foil,
preventing complete attachment to the
foil frame.
2. Align the water inlet surface and the
system outer foil mark ( ) and securely
attach together until it clicks.
►Replacing the inner blades
1. Remove the inner blades one at a time.
2. Insert the inner blades one at a time.
►Note
Do not throw away the foil frame.
►Replacement parts
Replacement parts are available at your dealer or Service Center.
Replacement parts for
ES‑BST6Q/ES‑BST2Q
System outer foil WES9087
Inner blades WES9068
17
English
FAQ
Question Answer
Will the battery deteriorate
if not used for an
extended period of time?
The battery will deteriorate if not
used for over 6 months, so make
sure to perform a full charge at
least once every 6 months.
Can I charge the shaver
after every use?
The battery used is a lithium‑ion,
so charging after every use will
have no effect on battery life.
Why should the adaptor
be disconnected after
charge?
Charging the battery for more than
1 hour will not affect battery
performance, but disconnect the
adaptor for safety and to save
energy.
What is the constituent of
the dedicated oil?
Constituent of the oil is liquid parafn.
Why does the appliance
beep twice after switched
off?
The sound indicates that the
battery capacity is running low.
Please charge the appliance.
Troubleshooting
Perform the following actions.
If the problems still cannot be solved, contact the store where
you purchased the unit or a service center authorized by
Panasonic for repair.
Problem Action
The power switch does
not turn ON.
Unlock the switch lock.
(See page 14.)
The power will not switch
to OFF. ES-BST6Q
Press the power switch twice
while using in shaving foam mode.
The shaving sensor does
not respond.
Depending on the beard
thickness or the amount of beard
trimmings in the shaver head, the
shaving sensor may not react and
the driving sound may not
change. This is not abnormal.
The shaving sensor may not
respond depending on the type
and quantity of the shaving gel.
This is not abnormal.
The shaving sensor may not
respond when the remaining
battery capacity is low. If this
happens, recharge the shaver.
Apply oil. (See page 15.)
The shaving sensor may not
respond when there is not enough
oil on the blades.
18
English
Problem Action
The shaving sensor
responds even though the
shaver is not in contact
with the skin.
Clean the beard trimmings from
the shaver.
When the shaver is extremely
dirty, remove the foil frame and
wash with water.
(See page 15.)
Replace the system outer foil and/
or inner blades.
Expected life of system outer foil
and inner blades:
System outer foil:
Approximately 1 year
Inner blades:
Approximately 2 years
Foam cannot be made in
shaving foam mode.
ES-BST6Q
Making foam may be difcult
depending on the type of facial
cleansers etc., so adjust the
amount of water or facial cleanser.
Foam made in shaving
foam mode contains
shavings. ES-BST6Q
Before making foam, cleanly rinse
off any shavings. (See page 14.)
The shaver cannot be
charged.
The recommended temperature
for charging is 10 °C – 35 °C. If
charged at a temperature other
than the recommended
temperature, the shaver may take
longer to charge or may not
charge at all.
Problem Action
Operating time is short
even after a full charge.
Although the shaver can be used
for about 2 weeks after a full
charge (assuming dry‑shave
usages for 3 minutes per day), the
usable number of days might be
lower depending on how or where
the shaver is used (for example,
when used for wet shaving).
Apply oil.
When the number of operations
per charge starts to decrease, the
battery is nearing the end of its life.
Shaver does not operate
even after charging.
Use the appliance in an ambient
temperature approximately 5 °C
or higher.
The battery has reached the end
of its life.
The shaver will not operate with
the AC adaptor connected.
Please use the shaver after it has
been sufciently charged and the
AC adaptor disconnected.
The driving sound
changes while shaving.
The shaving sensor is operating.
The sound changes depending on
the beard thickness.
19
English
Problem Action
Makes a loud sound.
Apply oil.
The blades will not move
smoothly when there is no oil on
the blades, requiring more power.
The shaver makes a high‑pitched
sound due to the linear motor drive.
This does not indicate a problem.
Conrm that the blades are
properly attached.
Clean the system outer foil with
the brush.
The odor is getting stronger.
This can be improved by cleaning
every time after shaving.
The shaver cannot be
properly cleaned even
after water is poured from
the water inlet.
When the shaver is very dirty, rst
use the cleaning brush to remove
beard trimmings.
Or, remove the foil frame and
wash with water.
(See page 15.)
Shavings y out in all
directions.
This can be improved by cleaning
every time after shaving.
Clean the inner blades with the
brush when shavings are
adhering to the inner blades.
Conrm that the cleaning shutter
is rmly closed.
System outer foil gets hot.
Apply oil.
Replace the system outer foil if it
is damaged or deformed.(See
page 16.)
Problem Action
You do not get as close a
shave as before.
Apply oil.
This can be improved by cleaning
every time after shaving.
Replace the system outer foil and/
or inner blades.
Expected life of system outer foil
and inner blades:
System outer foil:
Approximately 1 year
Inner blades:
Approximately 2 years
Battery life
The life of the battery is 3 years. The battery in this shaver is not
intended to be replaced by consumers. Have the battery replaced
by an authorized service center.
20
English
Removing the built-in rechargeable battery
Remove the built-in rechargeable battery before disposing of
the shaver�
Please make sure that the battery is disposed of at an ofcially
designated location if there is one.
This gure must only be used when disposing of the shaver, and
must not be used to repair it. If you dismantle the shaver yourself,
it will no longer be waterproof, which may cause it to malfunction.
• Remove the shaver from the AC adaptor.
• Press the power switch to turn on the power and then keep the
power on until the battery is completely discharged.
• Perform steps 1 to 6 and lift the battery, and then remove it.
• Take care not to short circuit the positive and negative terminals
of the removed battery, and insulate the terminals by applying
tape to them.
For environmental protection and recycling of materials
This shaver contains a Lithium‑ion battery.
Please make sure that the battery is disposed of at an ofcially
assigned location, if there is one in your country.
Specications
Power source See the name plate on the AC adaptor.
(Automatic voltage conversion)
Motor voltage 3.6 V
Charging time Approx. 1 hour
This product is intended for household use only.
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/