Makita DAS180 ユーザーマニュアル

ブランド: Makita

モデル: DAS180

カテゴリー: パワーツール

タイプ: ユーザーマニュアル

DAS180

EN Cordless Dust Blower INSTRUCTION MANUAL 9

ZHCN 充电式空气枪使用说明书 24

ID Blower Debu Tanpa Kabel PETUNJUK PENGGUNAAN 39

MS Penghembus Habuk Tanpa

Kord MANUAL ARAHAN 55

VI Máy Thổi Bụi Cầm Tay Hoạt

Động Bằng Pin TÀI LIỆU HƯỚNG DẪN 72

TH   87

Fig.1

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

Fig.9

Fig.10

1 1

Fig.11

Fig.12

Fig.13

Fig.14

Fig.15

Fig.16

Fig.17

Fig.18

Fig.19

Fig.20

Fig.21

Fig.22

Fig.23

Fig.24

Fig.25

Fig.26

Fig.27

Fig.28

Fig.29

Fig.30

Fig.31

Fig.32

Fig.33

Fig.34

Fig.35

Fig.36

Fig.37

Fig.38

Fig.39

Fig.40

Fig.41

Fig.42

Fig.43

Fig.44

Fig.45

Fig.46

Fig.47

9ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: DAS180

Air speed (average) *2 *3 163 m/s

Air speed (max.) *2 *3 200 m/s

Maximum air volume *1 *2 1.1 m3/min

Maximum

blowing force *1 *2

4: Max 2.8 N (0.29 kgf)

3: High 2.3 N (0.23 kgf)

2: Medium 1.7 N (0.17 kgf)

1: Low 1.1 N (0.11 kgf)

Continuous

use *1 *2

4: Max 15 min

3: High 20 min

2: Medium 30 min

1: Low 55 min

Maximum air pressure *2 *3 29.7 kPa

Dimensions (L x W x H) *1 *2 179 mm x 92 mm x 297 mm

Rated voltage D.C. 18 V

Net weight 1.2 - 1.7 kg

*1 Without nozzles

*2 With battery model BL1860B

*3 With nozzle 7

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsmaydierfromcountrytocountry.

• Theweightmaydierdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-

estcombinations,accordingtoEPTA-Procedure01/2014,areshowninthetable.

Applicable battery cartridge and charger

Battery cartridge BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B

Charger DC18RC/DC18RD/DC18RE/DC18SD/DC18SE/DC18SF/

DC18SH/DC18WC

• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof

residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

andchargersmaycauseinjuryand/orre.

10 ENGLISH

Applicable nozzles and attachments

Optional accessories

Nozzles and attachments Applications and purposes Diameters

Nozzle 3 Blowingairintoconnedspaces,corners,andspacesbythewallsto

dusto.

ø3.0 mm

Nozzle 7 Dustingolters. ø7.0 mm

Nozzle 13 Using as blower

Cleaning work surfaces and blowing dust in general.

Anchor hole cleaning with optional long nozzles.

Functioningasajointbetweenlongnozzlesandbloweroutletofthetool.

Using as inator

Inatinglargeinatablepoolsorairmattresses.

Using as deator

Deatinglargeinatablepoolsorairmattresses.

Functioningasajointbetweenairventhosecompleteandrubber

attachments.

ø13 mm

Wide range nozzle Blowing air over dirt and liquid on desktop and wide-open area.

Blowing range: 120° with 5 holes

ø6.0 mm

* As a single hole

diameter

Pinch valve nozzle Inating/deatingbeachtoys,pillows,andsimilarplasticinatables.

*Deatingoperationcanbecarriedoutwithoptionalairventhose

complete.

ø7.0 mm

Flexiblenozzle6 Blowingdustoutofanyhard-to-reachspots,PCsandsimilardevices. ø6.0 mm x 800 mm

11 ENGLISH

Nozzles and attachments Applications and purposes Diameters

Long nozzles set A set of nozzles suitable for blowing dust out of anchor holes and narrow

spots. Nozzle lengths can be changed by attaching and detaching two

nozzle heads.

*Longnozzlescanbeinstalledusingnozzle13asajoint.

ø8.0 mm

Air vent hose complete Deatinginatableitemswithappropriatenozzlesinoperation. -

Rubber attachment 20 - 30 Nozzleheadsuitablefordeatingairmattress,raft,boat,andpool.

*Thisattachmentrequirestobeinstalledwiththeairventhosecomplete

and nozzle 13 together.

ø20 - 30 mm

* Measured as outer

diameter.

Rubber attachment 65 Attachment suitable for packaging your clothes by compressing air out

of them.

*Thisattachmentrequirestobeinstalledwiththeairventhosecomplete

and nozzle 13 together.

ø65 mm

FilterC Attachment designed to reduce dust intake into the motor under dusty

working conditions.

12 ENGLISH

Symbols

Thefollowingsshowthesymbolswhichmaybeused

for the equipment. Be sure that you understand their

meaning before use.

Read instruction manual.

Keep hands away from rotating parts.

Long hair may cause entanglement

accident.

Keep bystanders away.

Wear eye and ear protection.

Do not expose to moisture.

Ni-MH

Li-ion

OnlyforEUcountries

Due to the presence of hazardous com-

ponentsintheequipment,wasteelectrical

andelectronicequipment,accumulators

and batteries may have a negative impact

on the environment and human health.

Do not dispose of electrical and electronic

appliances or batteries with household

waste!

InaccordancewiththeEuropeanDirective

on waste electrical and electronic equip-

ment and on accumulators and batteries

andwasteaccumulatorsandbatteries,

aswellastheiradaptationtonationallaw,

wasteelectricalequipment,batteriesand

accumulators should be stored separately

and delivered to a separate collection point

formunicipalwaste,operatinginaccor-

dance with the regulations on environmen-

tal protection.

Thisisindicatedbythesymbolofthe

crossed-out wheeled bin placed on the

equipment.

Intended use

Thetoolisintendedforblowingdust,inatingand

deatinginatables,withchangeablenozzlesaccording

toyourpreferences.Suitableforbothcommercialand

homeuse,e.g.,cleaningworkspaces,dustinglters,

andinatingbeachtoys.

SAFETY WARNINGS

General power tool safety warnings

WARNING Read all safety warnings, instruc-

tions, illustrations and specications provided with

this power tool.Failuretofollowallinstructionslisted

belowmayresultinelectricshock,reand/orserious

injury.

Save all warnings and instruc-

tions for future reference.

Theterm“powertool”inthewarningsreferstoyour

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical safety

1. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiedplugsandmatchingoutletswill

reduce risk of electric shock.

2. Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators.Thereisanincreasedriskofelec-

tric shock if your body is earthed or grounded.

3. Do not expose power tools to rain or wet con-

ditions. Water entering a power tool will increase

the risk of electric shock.

4. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

5. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

6. If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

7. Power tools can produce electromagnetic

elds (EMF) that are not harmful to the user.

However,usersofpacemakersandothersimilar

medical devices should contact the maker of their

device and/or doctor for advice before operating

this power tool.

Personal safety

1. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inuence of drugs, alcohol or med-

ication. A moment of inattention while operating

powertoolsmayresultinseriouspersonalinjury.

2. Use personal protective equipment. Always

wear eye protection. Protective equipment such

asadustmask,non-skidsafetyshoes,hardhator

hearing protection used for appropriate conditions

willreducepersonalinjuries.

13 ENGLISH

3. Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

yourngerontheswitchorenergisingpowertools

that have the switch on invites accidents.

4. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

resultinpersonalinjury.

5. Do not overreach. Keep proper footing and

balance at all times.Thisenablesbettercontrol

of the power tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts.Looseclothes,jewelleryor

long hair can be caught in moving parts.

7. If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

8. Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action

cancausesevereinjurywithinafractionofa

second.

9. Always wear protective goggles to protect

your eyes from injury when using power tools.

The goggles must comply with ANSI Z87.1 in

the USA, EN 166 in Europe, or AS/NZS 1336

in Australia/New Zealand. In Australia/New

Zealand, it is legally required to wear a face

shield to protect your face, too.

It is an employer's responsibility to enforce

the use of appropriate safety protective equip-

ments by the tool operators and by other per-

sons in the immediate working area.

Power tool use and care

1. Do not force the power tool. Use the correct

power tool for your application.Thecorrect

powertoolwilldothejobbetterandsaferatthe

rate for which it was designed.

2. Do not use the power tool if the switch does

not turn it on and o. Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

3. Disconnect the plug from the power source

and/or remove the battery pack, if detachable,

from the power tool before making any adjust-

ments, changing accessories, or storing power

tools.Suchpreventivesafetymeasuresreduce

the risk of starting the power tool accidentally.

4. Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

5. Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition that

may aect the power tool’s operation. If dam-

aged, have the power tool repaired before use.

Many accidents are caused by poorly maintained

power tools.

6. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

7. Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

foroperationsdierentfromthoseintendedcould

result in a hazardous situation.

8. Keep handles and grasping surfaces dry,

clean and free from oil and grease.Slippery

handles and grasping surfaces do not allow for

safe handling and control of the tool in unexpected

situations.

9. When using the tool, do not wear cloth work

gloves which may be entangled.Theentangle-

ment of cloth work gloves in the moving parts may

resultinpersonalinjury.

Battery tool use and care

1. Recharge only with the charger specied by

the manufacturer. A charger that is suitable for

onetypeofbatterypackmaycreateariskofre

when used with another battery pack.

2. Use power tools only with specically desig-

nated battery packs. Use of any other battery

packsmaycreateariskofinjuryandre.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another.Shortingthebatterytermi-

nalstogethermaycauseburnsorare.

4. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If con-

tact accidentally occurs, ush with water. If

liquid contacts eyes, additionally seek medical

help.Liquidejectedfromthebatterymaycause

irritation or burns.

5. Do not use a battery pack or tool that is dam-

aged or modied.Damagedormodiedbatteries

may exhibit unpredictable behaviour resulting in

re,explosionorriskofinjury.

6. Do not expose a battery pack or tool to re or

excessive temperature.Exposuretoreortem-

perature above 130 °C may cause explosion.

14 ENGLISH

7. Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specied in the instruc-

tions. Charging improperly or at temperatures

outsidethespeciedrangemaydamagethe

batteryandincreasetheriskofre.

Service

1. Have your power tool serviced by a qualied

repair person using only identical replacement

parts.Thiswillensurethatthesafetyofthepower

tool is maintained.

2. Never service damaged battery packs.Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

3. Follow instruction for lubricating and chang-

ing accessories.

Cordless Dust Blower Safety

Instructions

Training

1. Read the instructions carefully. Be familiar

with the controls and the correct use of the

dust blower.

2. Never allow children, persons with reduced

physical, sensory or mental capabilities or

lack of experience and knowledge or people

unfamiliar with these instructions to use the

dust blower. Local regulations may restrict the

age of the operator.

3. Never operate the dust blower while people,

especially children, or pets are nearby.

4. Keep in mind that the operator or user is

responsible for accidents or hazards occurring

to other people or their property.

Preparation

1. Do not wear loose clothing or jewellery that

can be drawn into the air inlet. Keep long hair

away from the air inlets.

2. To prevent dust irritation the wearing of a face

mask is recommended.

3. Use personal protective equipment. Always

wear eye protection. Protective equipment such

asadustmask,non-skidsafetyshoes,hardhator

hearing protection used for appropriate conditions

willreducepersonalinjuries.

Operation in general

1. Switch o the dust blower and remove the bat-

tery cartridge and make sure that all moving

parts have come to a complete stop

• whenever you leave the dust blower.

• whenever you switch from inating to

deating operation, and vice versa.

• before checking, cleaning or working on

the dust blower.

• if the dust blower starts to vibrate

abnormally.

2. Operate the dust blower only in daylight or in

good articial light.

3. Do not overreach and keep proper balance and

footing at all times.

4. Keep all cooling air inlets clear of debris.

5. Operate the dust blower in a recommended

position and on a rm surface.

6. Do not use the tool with wet hands.

7. Do not point the outlet of the nozzle and

attachment to yourself or others.Objectsmay

beblownawayandcauseaninjury.

8. Do not use the tool to spray chemicals. Your

lungs may be damaged by inhaling toxic fumes.

9. Do not operate the dust blower at high places.

10. Never block suction inlet and/or blower outlet.

• Be careful not to block suction inlet or

blower outlet with dust or dirt when oper-

ating in dusty area.

• Do not use nozzles other than the nozzles

provided by Makita.

11. If the dust blower strikes any foreign objects

or should start making any unusual noise

or vibration, immediately switch o the dust

blower to stop it. Remove the battery car-

tridge from the dust blower and inspect the

dust blower for damage before restarting and

operating the dust blower. If the dust blower

is damaged, ask Makita Authorized Service

Centers for repair.

12. Do not insert ngers or other objects into

suction inlet or blower outlet.

13. Prevent unintentional starting. Ensure the

switch is in the o-position before inserting

battery cartridge, picking up or carrying the

dust blower. Carrying the dust blower with

your nger on the switch or energizing the

dust blower that has the switch on invites

accidents.

14. Avoid operating the dust blower for a long time

in low temperature environment.

15. Do not use the tool beyond the maximum out-

put pressure of the tool. Using the tool at output

pressure greater than the maximum output pres-

sureofthetoolmaybursttheobjectorthetool.

Blowing operation

1. Never blow debris in the direction of

bystanders.

2. Never point the nozzle at anyone in the vicinity

when using the dust blower.

3. Never blow dangerous materials, such as

nails, fragments of glass, or blades.

4. Do not operate the dust blower near ammable

materials.

Inating/Deating operation

1. When inating objects, connect a nozzle or

attachment to the air inlet securely.Otherwise,

theobject,nozzle,orattachmentmaybedam-

agedandyoumaybeinjured.

2. Release air pressure slowly. When removing

a nozzle or attachment after inating objects,

hold the object, nozzle and attachment rmly.

Theymaybounceduetoexhaustairandcausean

injury.

3. Do not inate object beyond the maximum

pressure of the object.Otherwise,thetoolor

objectmaybedamagedandyoumaybeinjured.

15 ENGLISH

4. Inate the objects intended to be inated by

the manufacturer only, such as beach toys or

air mattress.Inatingotherobjectsmaydamage

themandcauseaninjury.

5. When inating objects, check the status of the

tool and object, and be sure that there is no air

leak from the object.

6. Always be careful not to over-inate objects

during operation. It otherwise may burst the

objects,possiblycausingdamagetothetooland

personalinjury.

7. After inating objects, check the air pressure

using a reliable and calibrated measuring

equipment.

8. Never leave the tool unattended when the

nozzle or attachment is attached to the object

or during operation.

9. Do not use the tool as a vacuum cleaner.

Performing dust collection may damage the tool.

10. Do not use the tool as a breathing device.

11. Use only standard accessories provided

by Makita.Theuseofanyotheraccessories

orattachmentsmightpresentariskofinjuryto

persons.

Maintenance and storage

1. Keep all nuts, bolts and screws tight to be sure

the dust blower is in safe working condition.

2. If the parts are worn or damaged, replace them

with parts provided by Makita.

3. Store the dust blower in a dry place out of the

reach of children.

4. When you stop the dust blower for inspection,

servicing, storage, or changing accessory,

switch o the dust blower and make sure that

all moving parts come to a complete stop, and

remove the battery cartridge. Cool down the

dust blower before making any work on the

dust blower. Maintain the dust blower with

care and keep it clean.

5. When carrying the tool, do not hold or pull a

nozzle or attachment.Thetoolmaybedamaged

andcauseaninjury.

6. Always cool down the dust blower before

storing.

7. Do not expose the dust blower to rain. Store

the dust blower indoors.

8. Do not disassemble the tool.

Service

1. Have your power tool serviced by a qualied

repair person using only identical replacement

parts.Thiswillensurethatthesafetyofthepower

tool is maintained.

2. Never service damaged battery packs.Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product.

MISUSE or failure to follow the safety rules stated

in this instruction manual may cause serious

personal injury.

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble or tamper with the battery

cartridge.Itmayresultinare,excessiveheat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge.Suchconductmayresultina

re,excessiveheat,orexplosion.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

Forcommercialtransportse.g.bythirdparties,

forwardingagents,specialrequirementonpack-

aging and labeling must be observed.

Forpreparationoftheitembeingshipped,consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tapeormaskoopencontactsandpackupthe

battery in such a manner that it cannot move

around in the packaging.

16 ENGLISH

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliantproductsmayresultinare,exces-

siveheat,explosion,orleakofelectrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge.Itmaycauseheating,catchingre,

burst and malfunction of the tool or battery car-

tridge,resultinginburnsorpersonalinjury.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near high-voltage electri-

cal power lines. It may result in a malfunction or

breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Useofnon-genuineMakitabatteries,orbatteriesthat

havebeenaltered,mayresultinthebatterybursting

causingres,personalinjuryanddamage.Itwill

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

ASSEMBLY

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before carrying out any work on the tool.

Installing nozzle

Aligntheguideprojectionsonanozzlewiththelocking

notchesonthelocksleeveofthetool,thenpushthe

nozzlermlyintothelocksleeveuntilitlocksinplace

withaclick.Havinginstalledthenozzle,trypullingit

back to ensure it is securely held in place.

►Fig.1: 1.Guideprojections2. Locking notches

3. Lock sleeve

NOTICE: Make sure that the nozzle has been

correctly attached to the tool so the guide pro-

jections on the nozzle neatly t into the locking

notches on the lock sleeve.

Removing nozzle

Hold the nozzle end and rotate it in a direction indicated

by the arrows on the nozzle end to release the lock. Pull

the nozzle apart from the lock sleeve after it becomes

unlocked.

►Fig.2: 1. Nozzle end 2. Lock sleeve

NOTICE: Adhered dirt and dust on the surface

will possibly make it hard to remove the nozzle

from the tool. In such a case, slide and hold the

lock sleeve towards the motor housing rst, and

then turn the nozzle end to release the lock.

CAUTION: Be careful not to pinch your hands

between the rear end of the lock sleeve and motor

housing while removing the nozzle.Thelock

sleeve slides back towards the motor housing when

the nozzle is released from the lock.

►Fig.3: 1. Lock sleeve 2. Motor housing

Removing and installing dust cap

1. Turnthedustcaponthesuctioninletattherearof

the housing counterclockwise to take the dust cap out

ofthehousing.Twolockingtabsonthedustcapcanbe

disengaged by aligning them with the guide grooves on

the housing.

►Fig.4: 1. Dust cap 2. Locking tabs 3.Suctioninlet

4. Guide grooves

2. Reassemblethedustcapontothesuctioninlet,

aligning the two locking tabs on the dust cap with the

guidegroovesonthehousing.Thenturnthedustcap

clockwise to secure it in place.

►Fig.5: 1. Dust cap 2. Locking tabs 3.Suctioninlet

4. Guide grooves

17 ENGLISH

Installing and removing long

nozzles

Optional accessory

A set of long nozzles helps clean dust out of small holes

and narrow spots. Nozzle lengths can be arranged

according to your requirements.

►Fig.6: 1. Nozzle 13 2. Long nozzle R 3. Long noz-

zleF

1. Insert the long nozzle R through the air hole of the

nozzle 13 from back to front. Pass it though until the

nozzle 13 secures in place at the rear end of the long

nozzle R.

►Fig.7: 1. Nozzle 13 2. Long nozzle R

2. PlacethelongnozzleFoverthefrontendofthe

longnozzleR.HandscrewthelongnozzleFuntilitis

tightened securely.

►Fig.8: 1.LongnozzleF2. Long nozzle R

3. Aligntheguideprojectionsonthenozzle13with

thelockingnotchesonthelocksleeveofthetool,then

pushthenozzle13rmlyintothelocksleeveuntilit

locks in place with a click.

►Fig.9: 1.Guideprojection2. Locking notch 3. Lock

sleeve 4. Nozzle 13 5. Long nozzle R 6. Long

nozzleF

NOTE: Use the long nozzle R only to have a shorter

operatingrange.UseboththelongnozzleRandFto

allow a wider operating range.

4. Toremovethelongnozzles,detachthenozzle13

fromthelocksleeveofthetool,andthendisassemble

the long nozzles.

Installing and removing deating

nozzles and attachments

Optional accessory

NOTICE: Always be sure to install and uninstall

deating nozzles and attachments only while the

air vent hose complete is disconnected from the

tool. Handling the air vent hose complete assembled

into the tool may cause the tool to stand unstable

resulting in it falling over.

1. Aligntheguideprojectionsonthepinchvalve

nozzle with the locking notches on the lock sleeve of the

airventhosecomplete,thenpushthepinchvalvenoz-

zlermlyintothelocksleeveuntilitlocksinplacewitha

click.

►Fig.10: 1. Pinch valve nozzle 2.Guideprojections

3. Locking notches 4. Lock sleeve 5. Air

vent hose complete

Optional rubber attachments

Optional rubber attachments require to be placed over

the nozzle. Be careful not to attach rubber attachments

directly to the air vent hose complete.

i Aligntheguideprojectionsonthenozzle13with

the locking notches on the lock sleeve of the air vent

hosecomplete,thenpushthenozzlermlyintothelock

sleeve until it locks in place with a click.

ii Place a rubber attachment over the nozzle head

by pushing and hand screwing it in place.

►Fig.11: 1. Rubber attachments 2. Nozzle 13 3. Air

vent hose complete

NOTICE: Make sure that the nozzle has been

correctly attached to the air vent hose complete

so the guide projections on the nozzle neatly t

into the locking notches on the lock sleeve.

2. Turnthedustcaponthesuctioninletattherearof

the housing counterclockwise to take the dust cap out

ofthehousing.Twolockingtabsonthedustcapcanbe

disengaged by aligning them with the guide grooves on

the housing.

►Fig.12: 1. Dust cap 2. Locking tabs 3.Suctioninlet

4. Guide grooves

3. Attach the end of the air vent hose complete to

thesuctioninlet,aligningthetwolockingtabsonthe

air vent hose complete with the guide grooves on the

housing.Thenholdandturntherearcusoftheairvent

hose complete clockwise to secure it in place.

►Fig.13: 1. Air vent hose complete 2.Rearcus

3.Suctioninlet4. Locking tabs 5. Guide

grooves

4. Toremovethedeatingnozzleandattachments,

follow the installation steps in reverse.

NOTICE: Always hold and turn the rear cus of

the air vent hose complete to install and uninstall

the air vent hose complete in place.

Installing optional lter

Optional accessory

Anoptionalhighperformancelter(FilterC)isavailable

for restricting dust intake into the motor under dusty

working conditions.

1. Turnthedustcaponthesuctioninletattherearof

the housing counterclockwise to take the dust cap out

ofthehousing.Twolockingtabsonthedustcapcanbe

disengaged by aligning them with the guide grooves on

the housing.

►Fig.14: 1. Dust cap 2. Locking tabs 3.Suctioninlet

4. Guide grooves

2. Replaceanoptionalhighperformancelteron

thesuctioninlet,aligningthetwolockingtabsonthe

optionallterwiththeguidegroovesonthehousing.

Thenturntheoptionallterclockwisetosecureitin

place.

►Fig.15: 1.Optionalhighperformancelter

2. Locking tabs 3.Suctioninlet4. Guide

grooves

NOTICE: An optional high performance lter

(Filter C) can be reused many times by cleaning it

out. Clean dust o the lter regularly as a clogged

lter may block the airow and cause less e-

cient operation. Occasionally wash the lter in

water, rinse and dry thoroughly in the shade

before use.

NOTICE: Do not wipe, rub or scratch an optional

high performance lter (Filter C) hardly. Be sure

to shake or blow dust o the lter with care.

18 ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch o the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge.Failuretoholdthetoolandthebattery

cartridgermlymaycausethemtoslipoyourhands

and result in damage to the tool and battery cartridge

andapersonalinjury.

►Fig.16: 1. Red indicator 2. Button 3. Battery

cartridge

Toremovethebatterycartridge,slideitfromthetool

while sliding the button on the front of the cartridge.

Toinstallthebatterycartridge,alignthetongueonthe

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator as

showninthegure,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen.Ifnot,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly.Ifthecartridgedoesnotslideineasily,itis

not being inserted correctly.

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

►Fig.17: 1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

catetheremainingbatterycapacity.Theindicatorlamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

Thebattery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydierslightly

from the actual capacity.

NOTE:Therst(farleft)indicatorlampwillblinkwhen

the battery protection system works.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem.Thissystemautomaticallycutsopowertothe

motortoextendtoolandbatterylife.Thetoolwillauto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the tool/battery is operated in a manner that

causesittodrawanabnormallyhighcurrent,thetool

stopsautomatically.Inthissituation,turnthetoolo

and stop the application that caused the tool to become

overloaded.Thenturnthetoolontorestart.

Overheat protection

Whenthetool/batteryisoverheated,thetoolstops

automatically.Inthissituation,letthetoolcooldown

before turning the tool on again.

Overdischarge protection

Whenthebatterybecomeslowonpowerduringuse,

thelampwillblinktoalertyou.Thenthetoolautomati-

callystops,withthelampremaininglitforapproximately

10seconds,shortlyafterthebatterypowerbecomes

toolowtooperateduringcontinuinguse.Insuchcases,

remove the battery from the tool and charge the battery.

19 ENGLISH

Protections against other causes

Protection system is also designed for other causes

that could damage the tool and allows the tool to stop

automatically.Takeallthefollowingstepstoclearthe

causes,whenthetoolhasbeenbroughttoatemporary

halt or stop in operation.

1. Turnthetoolo,andthenturnitonagainto

restart.

2. Charge the battery(ies) or replace it/them with

recharged battery(ies).

3. Let the tool and battery(ies) cool down.

If no improvement can be found by restoring protection

system,thencontactyourlocalMakitaServiceCenter.

Switch action

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the “OFF” position when released.

CAUTION: Switch can be locked in “ON”

position for ease of operator comfort during

extended use. Apply caution while locking tool in

“ON” position.

CAUTION: Do not install the battery cartridge

with the lock-on button engaged.

CAUTION: When not operating the tool,

depress the trigger-lock button from the side on

which a locking mark ( ) is indicated to lock the

switch trigger in the “OFF” position.

Trigger-lock button

Topreventtheswitchtriggerfrombeingaccidentally

pulled,thetrigger-lockbuttonisprovided.Tostartthe

tool,depressthetrigger-lockbuttonfromthesideon

which an unlocking mark ( )isindicated.Tolockthe

tool,depressthetrigger-lockbuttonfromthesideon

which a locking mark ( ) is indicated.

Make sure to set the trigger-lock button back in a lock-

ing position after each use.

►Fig.18: 1.Switchtrigger2.Trigger-lockbutton

3. Unlocking mark 4. Locking mark

NOTICE: Do not pull the switch trigger hard

without releasing the trigger-lock button.Thiscan

cause switch breakage.

Switch trigger

Air volume can be controlled by squeezing the switch

trigger. Air volume is grown by increasing pressure on

the switch trigger. Release the switch trigger to stop.

►Fig.19: 1.Switchtrigger

Lock button

Forcontinuousoperation,pushinthelockbuttonwhile

pulling the switch trigger and then release the switch

trigger.Tocancelthelocked-onoperation,pullthe

switchtriggerfully,thenreleaseit.

►Fig.20: 1.Switchtrigger2. Lock button

Adjusting air volume

Airvolumecanbechangedinfourmodes,thatis,

4(Max),3(High),2(Medium)and1(Low),depending

on the application and workload.

Presstheairvolumeadjustmentbuttontoswitchmode

inthefollowingsequence.Themodechangesevery

time you press the button.

►Fig.21: 1. Low air volume 2. Medium air volume

3. High air volume 4. Max air volume 5. Air

volumeadjustmentbutton

Air volume settings table

Air volume mode Maximum air volume

4: Max 1.1 m3/min

3: High 1.0 m3/min

2: Medium 0.8 m3/min

1: Low 0.6 m3/min

* Maximum air volumes are measured without

nozzles.

NOTE: Air volume mode can be changed before

turning the tool on.

NOTE:Thetoolrestartsoperationintheairvolume

mode that was last used.

Lighting up the lamp

CAUTION: Do not look in the light or see the

source of light directly.

Toturnthelampon,performoneofthefollowingsteps.

• Presstheairvolumeadjustmentbuttontolightthe

lampup.Thelampremainslitforapproximately

10 seconds.

• Pulltheswitchtriggertolightthelampup.The

lamp keeps on lighting while the switch trigger is

beingpulled.Thelampgoesoutapproximately

10 seconds after stopping operation.

NOTE:Whentheremainingbatterycapacitygetslow,

thelampstartsblinking.Thetiming,atwhichthelamp

starts blinking depends on the temperature at work

place and the battery cartridge conditions.

►Fig.22: 1.Airvolumeadjustmentbutton2.Switch

trigger 3. Lamp

Hanging hole

CAUTION: Before hanging the tool, always

make sure that the hanging hole is not damaged.

CAUTION: Use the hanging/mounting parts

for their intended purposes only. Using for unin-

tended purpose may cause accident or personal

injury.

CAUTION: Withstanding load rated for your

tools racks and holders needs to be learned

beforehand. Do not place the tool if it exceeds the

withstanding load on the racks and holders.

CAUTION: Be sure that the hanging hole is

securely hooked before releasing your hold.

20 ENGLISH

Use the hanging hole at the top rear of the housing to

hang the tool on a hook of racks and holders.

►Fig.23: 1. Hanging hole 2. Hook

Installing hook

Optional accessory

WARNING: Use the hanging/mounting parts

for their intended purposes only, e.g., hanging the

tool on a tool belt between jobs or work intervals.

WARNING: Be careful not to overload the

hook as too much force or irregular overburden

may cause damages to the tool resulting in per-

sonal injury.

CAUTION: When installing the hook, always

secure it with the screw rmly.Ifnot,thehook

maycomeofromthetoolandresultinthepersonal

injury.

CAUTION: Make sure to hang the tool

securely before releasing your hold.Insucient

orunbalancedhookingmaycausefallingoandyou

maybeinjured.

►Fig.24: 1. Groove 2. Hook 3.Screw

Thehookisconvenientfortemporarilyhangingthetool.

Thiscanbeinstalledoneithersideofthetool.Toinstall

thehook,insertitintoagrooveinthetoolhousingon

eithersideandthensecureitwithascrew.Toremove,

loosen the screw and then take it out.

OPERATION

CAUTION: Do not point the nozzle at anyone

nearby during operation.

NOTICE: Do not block suction inlet and/or

blower outlet during operation.

Blowing in general use

Recommended nozzles

— Nozzle 13

Cleanyourworksurfacesandoorsbyblowingodust,

dirt,debris,scraporwasteingeneral.

Direct the nozzle towards surfaces at an appropriate

distanceandswingitaroundtoblowoentirely.

►Fig.25

CAUTION: Never blow debris in the direction

of bystanders or pets.

CAUTION: Use personal protective equip-

ment such as a dust mask and eye protection.

NOTICE: Remove blockages on surfaces away

before blowing operation.

Blowing in conned spaces

Recommended nozzles

— Nozzle 3

Blowintoconnedspots,corners,andspacesbythe

wallstodusto.

Point the nozzle straight at spaces at a reasonable

distance and squeeze the switch trigger to control blow-

ing air volume.

►Fig.26

►Fig.27

CAUTION: Keep the nozzle away a reasonable

distance from blowing spots to avoid blowing up

dust into the air.

CAUTION: Use personal protective equip-

ment such as a dust mask and eye protection.

NOTICE: Avoid blocking the air vent holes

around the blower outlet. It otherwise may cause

suddennoiseandvibrationsandcouldpossiblyaect

the tool performance.

►Fig.28: 1. Air vent holes 2. Blower outlet

Dusting air lter

Recommended nozzles

— Nozzle 7

Dustltersurfacesbyblowingairthroughonesideof

theltertotheother.

Directthenozzleonltersurfaceswithinashortdis-

tance and swing it from side to side to blow dust away

from surfaces.

►Fig.29

CAUTION: Use personal protective equip-

ment such as a dust mask and eye protection.

NOTE: Point the nozzle at an angle according to the

outlinesoftheltersotheadhereddustcanbeeasily

removed.

Blowing wide and open area

Recommended nozzles

— Wide range nozzle

Blow air over dirt and liquid on wide-open surfaces such

asdesktopandoor,usingtheve-holenozzlewith

120 degree range of blowing.

Direct the nozzle over a large area within a certain

distance and swing it back and forth and from side to

side to blow widely.

►Fig.30

CAUTION: Use personal protective equip-

ment such as a dust mask and eye protection.

ページが読み込まれています...

Makita DAS180 ユーザーマニュアル

ブランド: Makita

モデル: DAS180

カテゴリー: パワーツール

タイプ: ユーザーマニュアル

PDFをダウンロードします

報告

Makita DAS180 ユーザーマニュアル

Makita DAS180 ユーザーマニュアル

関連論文

その他のドキュメント