DeWalt DCD991 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル

このマニュアルも適しています

DCD991
DCD996
B
English 3
简体中文 16
27
한국어
38
1
Figure 1
1
1
그림1
I
H
Q
G
E
D
B
A
F
I
J
DCD996
H
C
H
O
P
M
L
K
I
H
R
Figure 2
2
2
그림2
2
D
E
F
E
F
G
R
Figure 3
Figure 6
Figure 9
Figure 4
Figure 7
Figure 5
Figure 8
3
6
9
4
7
5
8
3
6
9
4
7
5
8
그림3
그림6
그림9
그림4
그림7
그림5
그림8
ENGLISH
3
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make DeWALT one of the most reliable
partners for professional power tool users.
Technical Data
DCD991 DCD996
Voltage
V
DC
18 18
Battery type Li-Ion Li-Ion
No load speed Drill, Driver/Hammer
1st gear
2nd gear
3rd gear
min
-
1
0450
01300
02000
0450/500
01300/1500
02000/2250
Impact rate
1st gear
2nd gear
3rd gear
min
-
1
08600
025,500
038,250
Max. torque (hard/soft)
hard Nm 95 95
soft Nm 66 66
Chuck capacity mm 1.513 1.513
Maximum drilling capcity
Wood
Metal
Masonry
mm 55
15
55
15
13
Weight (without battery pack) kg 1.5 1.6
BRUSHLESS CORDLESS 13 mm DRILL/DRIVER,
DCD991
BRUSHLESS CORDLESS 13 mm DRILL/DRIVER/
HAMMERDRILL, DCD996
English (original instructions)
4
ENGLISH
Charger DCB113
Mains voltage
V
AC
220-240
Battery type 10.8/14.4/18 Li-Ion
Approx. charging time
of battery packs
min 30 (1.3 Ah) 35 (1.5 Ah) 50 (2.0 Ah)
70 (3.0 Ah) 100 (4.0 Ah) 120 (5.0 Ah)
Weight kg 0.4
Charger DCB115
Mains voltage
V
AC
220-240
Battery type 10.8/14.4/18 Li-Ion
Approx. charging time
of battery packs
min 25 (1.3 Ah) 30 (1.5 Ah) 40 (2.0 Ah)
55 (3.0 Ah) 70 (4.0 Ah) 90 (5.0 Ah)
Weight kg 0.5
Charger DCB118
Mains voltage
V
AC
220-240
Battery type 18/54 Li-Ion
Approx. charging time
of battery packs
min 22 (1.3 Ah) 22 (1.5 Ah) 30 (2.0 Ah)
45 (3.0 Ah) 60 (4.0 Ah) 75 (5.0 Ah)
60 (6.0 Ah)
Weight kg 0.66
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal
word. Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of fire.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result
in electric shock, fire and/or serious
injury.
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN60745 and may be used to compare one tool with another. It
may be used for a preliminary assessment of exposure.
WARNING: The declared vibration emission
level represents the main applications of the
tool. However if the tool is used for different
applications, with different accessories or
poorly maintained, the vibration emission
may differ. This may significantly increase the
exposure level over the total working period.
An estimation of the level of exposure to
vibration should also take into account the
times when the tool is switched off or when
it is running but not actually doing the job.
This may significantly reduce the exposure
level over the total working period.
Identify additional safety measures to
protect the operator from the effects of
vibration such as: maintain the tool and
the accessories, keep the hands warm,
organisation of work patterns.
Battery pack DCB181 DCB182 DCB183/B
Battery type Li-Ion Li-Ion Li-Ion
Voltage
V
DC
18 18 18
Capacity Ah 1.5 4.0 2.0
Weight kg 0.35 0.61 0.40/0.45
Battery pack DCB184/B DCB185 DCB546
Battery type Li-Ion Li-Ion Li-Ion
Voltage
V
DC
18 18 18/54
Capacity Ah 5.0 1.3 6.0/2.0
Weight kg 0.62/0.67 0.35 1.05
Charger DCB107
Mains voltage
V
AC
220-240
Battery type 10.8/14.4/18 Li-Ion
Approx. charging time
of battery packs
min 60 (1.3 Ah) 70 (1.5 Ah) 90 (2.0 Ah)
140 (3.0 Ah) 185 (4.0 Ah) 240 (5.0 Ah)
Weight kg 0.29
Charger DCB112
Mains voltage
V
AC
220-240
Battery type 10.8/14.4/18 Li-Ion
Approx. charging time
of battery packs
min 40 (1.3 Ah) 45 (1.5 Ah) 60 (2.0 Ah)
90 (3.0 Ah) 120 (4.0 Ah) 150 (5.0 Ah)
Weight kg 0.36
5
ENGLISH
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
6
ENGLISH
Additional Specific Safety Rules for
Drills/Drivers/Hammerdrills
Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
Use auxiliary handle (s), if supplied with the
tool. Loss of control can cause personal injury.
Hold power tool by insulated gripping
surfaces when performing an operation
where the cutting accessory or the fastener
may contact hidden wiring. Cutting accessory
or fasteners contacting a “live” wire may make
exposed metal parts of the power tool “live” and
could give the operator an electric shock.
Use clamps or other practical way to secure
and support the workpiece to a stable
platform. Holding the work by hand or against
your body is unstable and may lead to loss of
control.
Wear ear protectors when hammering
for extended periods of time. Prolonged
exposure to high intensity noise can cause
hearing loss. Temporary hearing loss or serious
ear drum damage may result from high sound
levels generated by hammerdrilling.
Wear safety goggles or other eye protection.
Hammering and drilling operations cause chips
to fly. Flying particles can cause permanent eye
damage.
Hammer bits and tools get hot during
operation. Wear gloves when touching them.
Residual Risks
The following risks are inherent to the use of percussion drills:
Injuries caused by touching the rotating parts or
hot parts of the tool.
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be
avoided. These are:
Impairment of hearing.
Risk of squeezing fingers when changing
accessories.
Health hazards caused by breathing dust
developed when working in wood.
Risk of personal injury due to flying particles.
Risk of personal injury due to prolonged use.
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with another
battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery, avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
7
ENGLISH
DO NOT attempt to charge the battery pack
with any chargers other than the ones in
this manual. The charger and battery pack are
specifically designed to work together.
These chargers are not intended for
any uses other than charging
DeWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock or
electrocution.
Do not expose charger to rain or snow.
Pull by plug rather than cord when
disconnecting charger. This will reduce risk
ofdamage to electric plug and cord.
Make sure that cord is located so that it
will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
Do not use an extension cord unless it
is absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock, or electrocution.
Do not place any object on top of charger
or place the charger on a soft surface that
might block the ventilation slots and result
in excessive internal heat. Place the charger
in a position away from any heat source. The
charger is ventilated through slots in the top and
the bottom of the housing.
Do not operate charger with damaged cord
or plug—have them replaced immediately.
Do not operate charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way. Take it to an authorised
service centre.
Do not disassemble charger; take it to an
authorised service centre when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution or
fire.
In case of damaged power supply cord the
supply cord must be replaced immediately by
the manufacturer, its service agent or similar
qualified person to prevent any hazard.
Disconnect the charger from the outlet
before attempting any cleaning. This will
reduce the risk of electric shock. Removing
the battery pack will not reduce this risk.
• NEVER attempt to connect two chargers
together.
The charger is designed to operate on
standard 230V household electrical power.
Do not attempt to use it on any other
voltage. This does not apply to the vehicular
charger.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
DATE CODE POSITION
The Date Code, which also includes the year of manufacture, is
printed into the housing surface that forms the mounting joint
between tool and battery.
Example:
2016 XX XX
Year
of Manufacture
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual
contains important safety and operating
instructions for compatible battery chargers (refer to
TechnicalData).
Before using charger, read all instructions and
cautionary markings on charger, battery pack,
and product using battery pack.
WARNING: Shock hazard. Do not allow
any liquid to get inside charger. Electric
shock may result.
WARNING: We recommend the use of
a residual current device with a residual
current rating of 30mA or less.
CAUTION: Burn hazard. To reduce
the risk of injury, charge only DeWALT
rechargeable batteries. Other types of
batteries may burst causing personal
injury and damage.
CAUTION: Children should be
supervised to ensure that they do not
play with the appliance.
NOTICE: Under certain conditions, with
the charger plugged into the power
supply, the exposed charging contacts
inside the charger can be shorted by
foreign material. Foreign materials of
a conductive nature such as, but not
limited to, steel wool, aluminum foil or
any buildup of metallic particles should
be kept away from charger cavities.
Always unplug the charger from the
power supply when there is no battery
pack in the cavity. Unplug charger
before attempting to clean
8
ENGLISH
HOT/COLD PACK DELAY
When the charger detects a battery pack that is too hot or too cold,
it automatically starts a Hot/Cold Pack Delay, suspending charging
until the battery pack has reached an appropriate temperature. The
charger then automatically switches to the pack charging mode.
This feature ensures maximum battery pack life.
A cold battery pack will charge at a slower rate than a warm battery
pack. The battery pack will charge at that slower rate throughout
the entire charging cycle and will not return to maximum charge
rate even if the battery pack warms.
The DCB118 charger is equipped with an internal fan designed to
cool the battery pack. The fan will turn on automatically when the
battery pack needs to be cooled. Never operate the charger if the
fan does not operate properly or if ventilation slots are blocked. Do
not permit foreign objects to enter the interior of the charger.
LITHIUM-ION BATTERY PACKS ONLY
XR Li-Ion tools are designed with an Electronic Protection System
that will protect the battery pack against overloading, overheating
or deep discharge.
The tool will automatically turn off if the Electronic Protection
System engages. If this occurs, place the lithium-ion battery pack
on the charger until it is fully charged.
Wall Mounting
DCB107, DCB112, DCB113, DCB115, DCB118
These chargers are designed to be wall mountable or to sit upright
on a table or work surface. If wall mounting, locate the charger
within reach of an electrical outlet, and away from a corner or
other obstructions which may impede air flow. Use the back of
the charger as a template for the location of the mounting screws
on the wall. Mount the charger securely using drywall screws
(purchased separately) at least 25.4 mm long with a screw head
diameter of 79 mm, screwed into wood to an optimal depth
leaving approximately 5.5 mm of the screw exposed. Align the
slots on the back of the charger with the exposed screws and fully
engage them in the slots.
Charger Cleaning Instructions
WARNING: Shock hazard.
Disconnect the charger from the
AC outlet before cleaning. Dirt and
grease may be removed from the
exterior of the charger using a cloth
or soft non-metallic brush. Do not use
water or any cleaning solutions. Never
let any liquid get inside the tool; never
immerse any part of the tool into a
liquid.
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure to include
catalog number and voltage.
SAVE THESE INSTRUCTIONS
Chargers
The DCB107, DCB112, DCB113, and DCB115 chargers accept 10.8V,
14.4V, 18V Li-Ion XR and XR FLEXVOLTbattery packs (DCB123,
DCB125, DCB127, DCB141, DCB142, DCB143, DCB144, DCB145,
DCB181, DCB182, DCB183, DCB183B, DCB184, DCB184B, DCB185,
DCB546).
The DCB118 charger accepts 18V Li-Ion XR and XR FLEXVOLT
battery packs (DCB181, DCB182, DCB183, DCB183B, DCB184,
DCB184B, DCB185, DCB546).
DeWALT chargers require no adjustment and are designed to be as
easy as possible to operate.
Charging a Battery (Fig. 1)
1. Plug the charger into an appropriate outlet before inserting
battery pack.
2. Insert the battery pack (H) into the charger, making sure the
battery pack is fully seated in the charger. The red (charging)
light will blink repeatedly indicating that the charging process
has started.
3. The completion of charge will be indicated by the red light
remaining ON continuously. The battery pack is fully charged
and may be used at this time or left in the charger. To remove
the battery pack from the charger, push the battery release
button (I) on the battery pack.
NOTE: To ensure maximum performance and life of lithium-ion
battery packs, charge the battery pack fully before first use.
Charger Operation
Refer to the indicators below for the charge status of the battery
pack.
Charge Indicators: DCB107, DCB112, DCB113, DCB115, DCB118
Charging
Fully Charged
Hot/Cold Pack Delay*
* DCB107, DCB112, DCB113, DCB115, DCB118:
The red light will continue to blink, but a yellow indicator light will
be illuminated during this operation. Once the battery pack has
reached an appropriate temperature, the yellow light will turn off
and the charger will resume the charging procedure.
The compatible charger(s) will not charge a faulty battery pack.
The charger will indicate faulty battery by refusing to light or by
displaying problem pack or charger blink pattern.
NOTE: This could also mean a problem with a charger.
If the charger indicates a problem, take the charger and battery
pack to be tested at an authorised service centre.
9
ENGLISH
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM-ION
(LI-ION)
Do not incinerate the battery pack even
if it is severely damaged or is completely
worn out. The battery pack can explode in
a fire. Toxic fumes and materials are created
when lithium-ion battery packs are burned.
If battery contents come into contact with
the skin, immediately wash area with mild
soap and water. If battery liquid gets into the
eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte
is composed of a mixture of liquid organic
carbonates and lithium salts.
Contents of opened battery cells may
cause respiratory irritation. Provide fresh air.
If symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid
may be flammable if exposed to spark
or flame.
Transportation
WARNING: Fire hazard. Transporting
batteries can possibly cause fire if the
battery terminals inadvertently come in
contact with conductive materials. When
transporting batteries, make sure that
the battery terminals are protected and
well insulated from materials that could
contact them and cause a short circuit.
DeWALT batteries comply with all applicable shipping regulations
as prescribed by industry and legal standards which include
UN Recommendations on the Transport of Dangerous Goods;
International Air Transport Association (IATA) Dangerous Goods
Regulations, International Maritime Dangerous Goods (IMDG)
Regulations, and the European Agreement Concerning The
International Carriage of Dangerous Goods by Road (ADR). Lithium-
ion cells and batteries have been tested to section 38.3 of the UN
Recommendations on the Transport of Dangerous Goods Manual of
Tests and Criteria.
In most instances, shipping a DeWALT battery pack will be excepted
from being classified as a fully regulated Class 9 Hazardous Material.
In general, only shipments containing a lithium-ion battery with
an energy rating greater than 100 Watt Hours (Wh) will require
being shipped as fully regulated Class 9. All lithium-ion batteries
have the Watt Hour rating marked on the pack. Furthermore, due to
regulation complexities, DeWALT does not recommend air shipping
lithium-ion battery packs alone regardless of Watt Hour rating.
Shipments of tools with batteries (combo kits) can be air shipped
as excepted if the Watt Hour rating of the battery pack is no greater
than 100 Whr.
The battery pack is not fully charged out of the carton. Before using
the battery pack and charger, read the safety instructions below.
Then follow charging procedures outlined.
READ ALL INSTRUCTIONS
Do not charge or use battery in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting
or removing the battery from the charger may
ignite the dust or fumes.
Never force battery pack into charger. Do
not modify battery pack in any way to fit
into a non-compatible charger as battery
pack may rupture causing serious personal
injury.
Charge the battery packs only in DeWALT
chargers.
DO NOT splash or immerse in water or other
liquids.
Do not store or use the tool and battery
pack in locations where the temperature
may reach or exceed 40 ˚C (104 ˚F) (such
as outside sheds or metal buildings in
summer).
WARNING: Never attempt to open the
battery pack for any reason. If battery
pack case is cracked or damaged,
do not insert into charger. Do not
crush, drop or damage battery pack.
Do not use a battery pack or charger
that has received a sharp blow, been
dropped, run over or damaged in any
way (i.e., pierced with a nail, hit with a
hammer, stepped on). Electric shock
or electrocution may result. Damaged
battery packs should be returned to
service centre for recycling.
WARNING: Fire hazard. Do not store
or carry the battery pack so that
metal objects can contact exposed
battery terminals. For example, do
not place the battery pack in aprons,
pockets, tool boxes, product kit boxes,
drawers, etc., with loose nails, screws,
keys, etc.
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large
battery packs will stand upright on the
battery pack but may be easily knocked
over.
10
ENGLISH
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the labels on the
charger and the battery pack may show the following pictographs:
Read instruction manual before use.
See Technical Data for charging time.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Do not expose to water.
Have defective cords replaced immediately.
Charge only between 4 ˚C and 40 ˚C.
Only for indoor use.
Discard the battery pack with due care for the
environment.
Charge DeWALT battery packs only with designated
DeWALT chargers. Charging battery packs other than
the designated DeWALT batteries with a DeWALT
charger may make them burst or lead to other
dangerous situations.
Do not incinerate the battery pack.
Use: Use without transportation cap, Wh rating
indicates 108 Wh (1 battery with 108 Wh).
Transport: Transport with built-in transport cap, Wh
rating indicates 3 x 36 Wh (3batteries of 36 Wh).
Package Contents
The package contains:
1 Brushless cordless drill/driver (DCD991)
1 Brushless cordless hammerdrill (DCD996)
1 Li-Ion battery packs (M1, P1, T1)
2 Li-Ion battery packs (M2, P2, T2)
3 Li-Ion battery packs (M3, P3, T3)
1 Tool Connect
TM
App instruction manual
Regardless
of whether a shipment is considered excepted or fully
regulated, it is the shipper's responsibility to consult the latest
regulations for packaging, labeling/marking and documentation
requirements.
The information provided in this section of the manual is provided
in good faith and believed to be accurate at the time the document
was created. However, no warranty, expressed or implied, is given.
It is the buyers responsibility to ensure that its activities comply
with the applicable regulations.
TRANSPORTING THE FLEXVOLT™ BATTERY
The DeWALT FLEXVOLTbattery has two modes: Use and
Transport.
Use Mode: When the FLEXVOLTbattery stands alone or is
in a DeWALT 18V product, it will operate as an 18V battery. When
the FLEXVOLTbattery is in a 54V or a 108V (two 54V batteries)
product, it will operate as a 54V battery.
Transport Mode: When the cap is attached to the FLEXVOLT
battery, the battery is in transport mode. Keep the cap for shipping.
When in Transport mode, strings
of cells are electrically
disconnected within the
pack resulting in 3
batteries with a lower Watt hour (Wh) rating as compared to 1
battery with a higher Watt hour rating. This increased quantity of 3
batteries with the lower Watt hour rating can exempt the pack from
certain shipping regulations that are imposed upon the higher Watt
hour batteries.
Transport Wh rating
EXAMPLE OF USE AND
TRANSPORT LABEL MARKING
indicates 3x36 Wh,
meaning 3 batteries
of 36 Watt hours each.
The Use Wh rating
indicates 108 Watt hours (1 battery implied).
Battery Pack
BATTERY TYPE
The DCD991 and DCD996 operate on a 18V Li-Ion XR and
XRFLEXVOLT
TM
battery packs
These
battery packs may be used: DCB181, DCB182, DCB183,
DCB183B, DCB184, DCB184B, DCB185, DCB546. Refer to
Technical Data for moreinformation.
Storage Recommendations
1. The best storage place is one that is cool and dry away
from direct sunlight and excess heat or cold. For optimum
battery performance and life, store battery packs at room
temperature when not in use.
2. For long storage, it is recommended to store a fully charged
battery pack in a cool, dry place out of the charger for optimal
results.
NOTE:
Battery packs should not be stored completely depleted
of charge. The battery pack will need to be recharged before use.
11
ENGLISH
DO NOT
use under wet conditions or in presence of flammable
liquids or gases.
These drills/drivers/hammerdrills are professional power tools.
DO NOT
let children come into contact with the tool.
Supervision is required when inexperienced operators use this tool.
Young children and the infirm.
This appliance
is not intended for use by young children or infirm persons
without supervision.
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills unless
they are supervised by a person responsible for their safety.
Children should never be left alone with this product.
Electrical Safety
The electric motor has been designed for one voltage only. Always
check that the battery pack voltage corresponds to the voltage on
the rating plate. Also make sure that the voltage of your charger
corresponds to that of your mains.
Your DeWALT charger is double insulated in
accordance with IEC60335; therefore no earth wire is
required.
If the supply cord is damaged, it must be replaced by a specially
prepared cord available through the DeWALT service organization.
Using an Extension Cable
An extension cord should not be used unless absolutely necessary.
Use an approved extension cable suitable for the power input of
your charger (see Technical Data). The minimum conductor
size is 1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
WARNING: Use only DeWALT battery
packs and chargers.
Inserting and Removing the
Battery Pack from the Tool (Fig. 2)
NOTE: For best results, make sure your battery pack is fully
charged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the battery pack (H) with the rails inside the tools
handle (Fig. 2).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that it does not disengage.
1 Kitbox
1
Charger
1 Side handle
1
Instruction manual
NOTE: Battery packs, chargers and kitboxes are not included with
N-models. Battery packs and chargers are not included with NT
models. Bmodels include Bluetooth
®
battery packs.
NOTE: The Bluetooth
®
word mark and logos are registered
trademarks owned by the Bluetooth
®
, SIG, Inc. and any use of such
marks by DeWALT is under license. Other trademarks and trade
names are those of their respective owners.
Check for damage to the tool, parts or
accessories which may have occurred during
transport.
Take the time to thoroughly read and
understand this manual prior to operation.
Description (Fig. 1)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
A. Trigger switch
B. Forward/reverse control button
C. Worklight
D. Chuck
E. Torque adjustment collar
F. Gear shifter
G. Side handle
H. Battery pack
I. Battery release button
J. Belt hook
K. Mounting screw
L. Magnetic bit holder
M. Worklight switch
N. Low worklight mode
O. Medium worklight mode
P. Spotlight mode
Q. Fuel gauge
R. Main handle
INTENDED USE
These drills drivers/hammerdrills are designed for professional
drilling, percussion drilling and screwdriving applications. This tool
is compatible with Bluetooth
®
Battery Technology and with the
DeWALT Tool Connect
TM
App. Please see your Tool Connect
TM
App
instruction manual for more information.
12
ENGLISH
To select forward rotation, release the trigger switch and depress
the for ward/re verse control button on the right side of the tool.
To select reverse, release the trigger switch and depress the
forward/reverse control button on the left side of the tool.
The center position of the control button locks the tool in the off
position. When changing the position of the control button, be sure
the trigger is released.
NOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start up. This is normal and does
not indicate a problem.
Torque Adjustment Collar/Electronic
Clutch (Fig. 35)
Your tool has an electronic adjustable torque screwdriver
mechanism for driving and removing a wide array of fasteners.
Circling the torque adjustment collar (E) are numbers. These
numbers are used to set the clutch to deliver a torque range.
The higher the number on the collar, the higher the torque and
the larger the fastener which can be driven. To select any of the
numbers, rotate until the desired number aligns with the arrow.
Three-Speed Gearing (Fig. 1, 35)
The three-speed feature of your tool allows you to shift gears for
greater versatility. To select speed 1 (highest torque setting), turn
the tool off and permit it to stop. Slide the gear shifter (F) all the
way forward. Speed 2 (middle torque and speed setting) is in the
middle position. Speed 3 (highest speed setting) is to the rear.
NOTE:
Do not change gears when the tool is running. Always
allow the drill to come to a complete stop before changing gears. If
you have trouble changing gears, make sure that the gear shifter is
engaged in one of the three speed settings.
If the speed shifter becomes stuck or is difficult to select the desired
gear, pull the trigger switch (A) to rotate the motor. Then select
the gear.
Keyless Single Sleeve Chuck
(Fig. 68)
WARNING: Do not attempt to tighten
drill bits (or any other accessory) by
gripping the front part of the chuck
and turning the tool on. Damage to
the chuck and personal injury may
result. Always lock off trigger switch
and disconnect tool from power source
when changing acces sories.
WARNING: Always ensure the bit is
secure before starting the tool. A loose
bit may eject from tool causing possible
personal injury.
Your tool features a keyless chuck with one rotating sleeve for
one-handed operation of the chuck. To insert a drill bit or other
accessory, follow these steps.
1. Turn off tool and disconnect tool from power source.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the battery release button (I) and firmly pull the battery
pack out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Squeeze the tool trigger for three seconds to dissipate the slight
electric charge that may still be in the tool. The worklight may come
on for a brief moment.
FUEL GAUGE BATTERY PACKS (FIG. 2)
Some DeWALT battery packs include a fuel gauge which consists of
three green LED lights that indicate the level of charge remaining in
the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button
(Q). A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge in the
battery is below the usable limit, the fuel gauge will not illuminate
and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the charge left
on the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Variable Speed Switch (Fig. 1)
To turn the tool on, squeeze the trigger switch (A). To turn the tool
off, release the trigger switch. Your tool is equipped with a brake.
The chuck will stop as soon as the trigger switch is fully released.
NOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should be avoided.
Side Handle (Fig. 1)
WARNING: To reduce the risk of
personal injury, ALWAYS operate
the tool with the side handle properly
installed. Failure to do so may result
in the side handle slipping during tool
operation and subsequent loss of
control. Hold tool with both hands to
maximize control.
The side handle (G) clamps to the front of the gear case and may be
rotated 360˚ to permit right- or left-hand use. Side handle must be
tightened sufficiently to resist the twisting action of the tool if the
accessory binds or stalls. Be sure to grip the side handle at the far
end to control the tool during astall.
If model is not equipped with side handle, grip drill with one hand
on the handle and one hand on the battery pack.
NOTE: Side handle comes equipped on all models.
Forward/Reverse Control Button
(Fig. 1)
A forward/reverse control button (B) determines the direction of
the tool and also serves as a lock off button.
13
ENGLISH
Belt Hook and Magnetic Bit Holder
(Fig. 1)
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
WARNING: To reduce the risk of
serious personal injury, DO NOT
suspend tool overhead or suspend
objects from the belt hook. ONLY hang
tool’s belt hook from a work belt.
WARNING: To reduce the risk of
serious personal injury, ensure the
screw holding the belt hook is secure.
CAUTION: To reduce the risk of
personal injury or damage, DO NOT
use the belt hook to hang the drill
while using as a spotlight.
IMPORTANT: When attaching or replacing the belt hook or
magnetic bit holder, use only the screw (K) that is provided. Be sure
to securely tighten the screw.
The belt hook (J) and magnetic bit holder (L) can be be attached
to either side of the tool using only the screw (K) provided, to
accommodate left- or right- handed users. If the hook or magnetic
bit holder is not desired at all, it can be removed from the tool.
To move belt hook or magnetic bit holder, remove the screw (K)
that holds it in place then reassemble on the opposite side. Be sure
to securely tighten the screw.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
Proper Hand Position (Fig. 9)
WARNING: To reduce the risk of
serious personal injury, ALWAYS
use proper hand position as shown
infigure9.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
2. Grasp the black sleeve of the chuck (D) with one hand and use
the other hand to secure the tool as shown in Figure 6. Rotate
the sleeve counterclockwise (as viewed from the front) far
enough to accept the desired accessory.
3. Insert the accessory about 19 mm into the chuck (Fig. 7).
Tighten securely by rotating the chuck sleeve clockwise with
one hand while holding the tool with the other hand (Fig. 8).
Continue to rotate the chuck sleeve until several ratchet clicks
are heard to ensure full gripping power.
To release the accessory, repeat Steps 1 and 2 above.
Be sure to tighten chuck with one hand on the chuck sleeve and
one hand holding the tool for maximum tightness.
LED Worklight (Fig. 1)
The LED worklight (C) and its worklight switch (M) are located on
the foot of the tool. The worklight is activated when the trigger
switch is depressed. The low (N), medium (O) and spotlight (P)
modes can be changed by moving the switch on the foot of the
tool. If the trigger switch remains depressed, the worklight will
remain on in all modes.
When on low (N) and medium (O) settings, the beam will
automatically turn off 20 seconds after the trigger switch is
released.
SPOTLIGHT MODE
The high setting (P) is the spotlight mode. The spotlight will run for
20 minutes after the trigger switch is released. Two minutes before
the spotlight will shut off, it will flash twice and then dim. To avoid
the spotlight shutting off, lightly tap the trigger switch.
WARNING: While using the worklight in
medium or spotlight mode, do not stare
at the light or place the drill in a position
which may cause anyone to stare into
the light. Serious eye injury could result.
CAUTION: When using the tool as a
spotlight, be sure it is secured on a
stable surface where it will not cause a
tripping or falling hazard.
CAUTION: Remove all accessories
from the chuck before using the drill as
a spotlight. Personal injury or property
damage could result.
LOW BATTERY WARNING
When in spotlight mode and the battery is nearing complete
discharge, the spotlight will flash twice and then dim. After two
minutes, the battery will be completely discharged and the drill
will immediately shut down. At this point, replace with a charged
battery.
WARNING: To reduce the risk of
injury, always have a back-up battery
or secondary lighting available if the
situation warrants it.
14
ENGLISH
NOTE:
Use the lowest torque setting (1) first and increase
the number through to the highest setting (11) to seat the
fastener at the desired depth. The lower the number, the
lower the torque output.
2. Reset the torque adjustment collar (E) to the appropriate
number setting for the torque desired. Make a few practice
runs in scrap or unseen areas to determine the proper position
of the torque adjustment collar.
NOTE: The torque adjustment collar may be set to any number
at any time.
Hammerdrill Operation (Fig. 5)
1. Select the desired speed/torque range using the gear shifter
to match the speed and torque to the planned operation. Set
the torque adjustment collar (E) to the hammer symbol.
2. Select the high speed 3 setting by sliding the gear shifter (F)
back (away form the chuck).
3. When drilling, use just enough force on the hammer to
keep it from bouncing excessively. Prolonged and too much
force on the hammer will cause slower drilling speeds and
potential overheating.
4. Drill straight, keeping the bit at a right angle to the work. Do
not exert side pressure on the bit when drilling as this will
cause clogging of the bit flutes and a slower drilling speed.
5. When drilling deep holes, if the hammer speed starts to drop
off, pull the bit partially out of the hole with the tool still
running to help clear debris from the hole.
6. For masonry, use carbide-tipped bits or masonry bits. A
smooth, even flow of dust indicates the proper drilling rate.
MAINTENANCE
Your DeWALT power tool has been designed to operate over a
long period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and regular
cleaning.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the main handle (R),
with the other hand on the side handle(G).
Drill Operation (Fig. 4)
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
WARNING: To reduce the risk of
personal injury, ALWAYS ensure
workpiece is anchored or clamped
firmly. If drilling thin material, use a wood
“back-up” block to prevent damage to
the material.
1. Select the desired speed/torque range using the gear shifter
to match the speed and torque to the planned operation. Set
the torque adjustment collar (E) to the drill symbol.
2. For WOOD, use twist bits, spade bits, power auger bits or
hole saws. For METAL, use high-speed steel twist drill bits or
hole saws. Use a cutting lubricant when drilling metals. The
exceptions are cast iron and brass which should be drilled dry.
3. Always apply pressure in a straight line with the bit. Use
enough pressure to keep the drill bit biting, but do not push
hard enough to stall the motor or deflect the bit.
4. Hold tool firmly with both hands to control the twisting
action of the drill.
5. IF DRILL STALLS, it is usually because it
is being overloaded. RELEASE TRIGGER
IMMEDIATELY, remove drill bit from work, and
determine cause of stalling. DO NOT CLICK
TRIGGER OFF AND ON IN AN ATTEMPT
TO START A STALLED DRILL THIS CAN
DAMAGE THE DRILL.
6. Keep the motor running when pulling the bit back out of a
drilled hole. This will help prevent jamming.
Screwdriver Operation (Fig. 3)
1. Select the desired speed/torque range using the three-speed
gear shifter (F) on the top of the tool. If using the torque
adjustment collar (E), initially set the three-speed gear
shifter to speed 2 or 3. This ensures effective control over the
fastener allowing the screw to be seated correctly and set to
specification. Speed 1 will provide the same clutching torque
as speeds 2 and 3. However, for optimum performance of the
electronic clutch, speeds 2 and 3 are preferred.
15
ENGLISH
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
Optional Accessories
WARNING: Since accessories, other
than those offered by DeWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DeWALT recommended
accessories should be used with this
product.
Consult your dealer for further information on the appropriate
accessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand
for raw materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails to
produce sufficient power on jobs which were easily done before.
At the end of its technical life, discard it with due care for our
environment:
Run the battery pack down completely, then remove it from
the tool.
Li-Ion cells are recyclable. Take them to your dealer or a local
recycling station. The collected battery packs will be recycled
or disposed of properly.
16
简体中文
技术参数
DCD991 DCD996
电压 伏特
直流
20/18 20/18
电池类型 锂离子 锂离子
空载转速 电钻、起子/冲击钻
1
2
3
转/分
0–450
0–1300
0–2000
0–450/500
0–1300/1500
0–2000/2250
冲击率
1
2
3
转/分
0–8600
0–25,500
0–38,250
最大扭矩 (硬/软)
牛米
95 95
牛米
66 66
夹头尺寸 毫米
1.5–13 1.5–13
最大钻孔能力
木材
金属
砖石
毫米
55
15
55
15
13
重量 (不含电池组) 千克
1.5 1.6
注意:20V Max为最大初始电池电压(无负载测量),额定电压为18V
60V Max为最大初始电池电压(无负载测量),额定电压为54V
充电式无刷13毫米电钻/起子,DCD991
充电式无刷13毫米电钻/起子/冲击钻,DCD996
恭喜!
感谢您选购DeWALT工具。凭借多年的产品开发和创新经验,DeWALT已经成为专业电动工具用户最可
靠的合作伙伴之一。
简体中文(原始说明)
17
简体中文
充电器
DCB115
电源电压
伏特
交流
220
电池类型
10.8/14.4/18 锂离子
电池组的大约
充电时间
分钟
25 (1.3
安时)
30 (1.5
安时)
40 (2.0
安时)
55 (3.0
安时)
70 (4.0
安时)
90 (5.0
安时)
重量
千克
0.5
充电器
DCB118
电源电压
伏特
交流
220
电池类型
18/54 锂离子
电池组的大约
充电时间
分钟
22 (1.3
安时)
22 (1.5
安时)
30 (2.0
安时)
45 (3.0
安时)
60 (4.0
安时)
75 (5.0
安时)
60 (6.0
安时)
重量
千克
0.66
定义:安全指南
下列定义描述了各标志术语的严重程度。请仔细阅
读本手册,并注意这些标志。
危险:表示存在紧急危险情况,如果不
加以避免,导致死亡或严重伤害
警告:表示存在潜在的危险情况,如果不
加以避免,可能导致死亡或严重伤害
警示:表示存在潜在危险情况,如果不
加以避免,可能导致轻度或中度伤害
注意:表示存在不涉及人身伤害的情况,
如果不加以避免,可能导致财产损失
表示存在触电风险。
表示存在火灾风险。
电动工具通用安全警告
警告!阅读随电动工具提供的所有安全
警告、说明、图示和规定。不遵照以下
所列说明会导致电击、着火和/或严
重伤害。
保存所有警告和说明书以备查阅。
警告中的术语“电动工具”指市电驱动(有线)电
动工具或电池驱动(无线)电动工具。
a) 工作场地的安全
1)
保持工作场地清洁和明亮。杂乱和黑暗的场
地会引发事故。
电池组
DCB181 DCB182 DCB183/B
电池类型 锂离子 锂离子 锂离子
电压 伏特
直流
18 18 18
电池容量 安时
1.5 4.0 2.0
重量 千克
0.35 0.61 0.40/0.45
电池组
DCB184/B DCB185 DCB546
电池类型 锂离子 锂离子 锂离子
电压 伏特
直流
18 18 18/54
电池容量 安时
5.0 1.3 6.0/2.0
重量 千克
0.62/0.67 0.35 1.05
电池组
DCB204
电池类型
电压
V
DC
20
电池容量
Ah 4.0
重量
0.61
充电器
DCB107
电源电压
伏特
交流
220
电池类型
10.8/14.4/18 锂离子
电池组的大约
充电时间
分钟
60 (1.3
安时)
70 (1.5
安时)
90 (2.0
安时)
140 (3.0
安时)
185 (4.0
安时)
240 (5.0
安时)
重量
千克
0.29
充电器
DCB112
电源电压
伏特
交流
220
电池类型
10.8/14.4/18 锂离子
电池组的大约
充电时间
分钟
40 (1.3
安时)
45 (1.5
安时)
60 (2.0
安时)
90 (3.0
安时)
120 (4.0
安时)
150 (5.0
安时)
重量
千克
0.36
充电器
DCB113
电源电压
伏特
交流
220
电池类型
10.8/14.4/18 锂离子
电池组的大约
充电时间
分钟
30 (1.3
安时)
35 (1.5
安时)
50 (2.0
安时)
70 (3.0
安时)
100 (4.0
安时)
120 (5.0
安时)
重量
千克
0.4
18
简体中文
d) 电动工具使用和注意事项
1)
不要勉强使用电动工具,根据用途使用合适
的电动工具。选用合适的按照额定值设计的
电动工具会使你工作更有效、更安全。
2)
如果开关不能接通或关断电源,则不能使用
该电动工具。不能通过开关来控制的电动工
具是危险的且必须进行修理。
3)
在进行任何调节、更换附件或贮存电动工具
之前,必须从电源上拔掉插头和/或卸下电
池包(如可拆卸)。这种防护性的安全措施
降低了电动工具意外起动的风险。
4)
将闲置不用的电动工具贮存在儿童所及范围
之外,并且不允许不熟悉电动工具和不了解
这些说明的人操作电动工具。电动工具在未
经培训的使用者手中是危险的。
5)
维护电动工具及其附件。检查运动部件是否
调整到位或卡住,检查零件破损情况和影响
电动工具运行的其他状况。如有损坏,应在
使用前修理好电动工具。许多事故是由维护
不良的电动工具引发的。
6)
保持切削刀具锋利和清洁。维护良好地有锋
利切削刃的刀具不易卡住而且容易控制。
7)
照使用说明书,并考虑作业条件和要进行
的作业来选择电动工具、附件和工具的刀头
等。将电动工具用于那些与其用途不符的操
作可能会导致危险情况。
8)
保持手柄和握持表面干燥、清洁,不得沾有
油脂。在意外的情况下,湿滑的手柄不能保
证握持的安全和对工具的控制。
e) 电池式工具使用和注意事项:
1)
仅使用生产者规定的充电器充电。将适用于
某种电池包的充电器用到其他电池包时可能
会发生着火危险。
2)
仅使用配有专用电池包的电动工具。使用其
他电池包可能会产生伤害和着火危险。
3)
当电池包不用时,将它远离其他金属物体,
例如回形针、硬币、钥匙、钉子、螺钉或
其他小金属物体,以防电池包一端与另一
端连接。电池组端部短路可能会引起燃烧
或着火。
4)
在滥用条件下,液体可能会从电池组中溅
出,应避免接触。如果意外碰到液体,用水
冲洗。如果液体碰到了眼睛,还应寻求医疗
帮助。从电池中溅出的液体可能会发生腐蚀
或燃烧。
5)
不要使用损坏或改装过的电池包或工具。
坏或改装过的电池组可能呈现无法预测的结
果,导致着火、爆炸或伤害。
6)
不要将电池包暴露于火或高温中。电池包
暴露于火或高于130°C的高温中可能导致
爆炸。
f) 维修
1)
让专业维修人员使用相同的备件维修电动工
具。这将保证所维修的电动工具的安全。
2)
不要在易爆环境,如有易燃液体、气体或粉
尘的环境下操作电动工具。电动工具产生的
火花会点燃粉尘或气体。
3)
操作电动工具时,远离儿童和旁观者。注意
力不集中会使你失去对工具的控制。
b) 电气安全
1)
电动工具插头必须与插座相配。绝不能以任
何方式改装插头。需接地的电动工具不能使
用任何转换插头。未经改装的插头和相配的
插座将降低电击风险。
2)
免人体接触接地表面,如管道、散热片和
冰箱。如果你身体接触接地表面会增加电
击风险。
3)
不得将电动工具暴露在雨中或潮湿环境中。
水进入电动工具将增加电击风险。
4)
不得滥用软线。绝不能用软线搬运、拉动
电动工具或拔出其插头。使软线远离热源、
油、锐边或运动部件。受损或缠绕的软线会
增加电击风险。
5)
当在户外使用电动工具时,使用适合户外使
用的延长线。适合户外使用的电线将降低电
击风险。
6)
如果无法避免在潮湿环境中操作电动工具,
应使用带有剩余电流装置(RCD)保护的电
源。RCD的使用可降低电击风险。
c) 人身安全
1)
保持警觉,当操作电动工具时关注所从事
的操作并保持清醒。当你感到疲倦,或在有
药物、酒精或治疗反应时,不要操作电动工
具。在操作电动工具时瞬间的疏忽会导致严
重人身伤害。
2)
使用个人防护装置。始终佩戴护目镜。防护
装置,诸如适当条件下使用防尘面具、防滑
安全鞋、安全帽、听力防护等装置能减少人
身伤害。
3)
防止意外起动。在连接电源和/或电池包、拿
起或搬运工具前确保开关处于关断位置。
指放在开关上搬运工具或开关处于接通时通
电会导致危险。
4)
在电动工具接通之前,拿掉所有调节钥匙或
扳手。遗留在电动工具旋转零件上的扳手或
钥匙会导致人身伤害。
5)
手不要过分伸展。时刻注意立足点和身体平
衡。这样能在意外情况下能更好地控制住电
动工具
6)
着装适当。不要穿宽松衣服或佩戴饰品。让
你的头发和衣服远离运动部件。宽松衣服、
佩饰或长发可能会卷入运动部件。
7)
如果提供了与排屑、集尘设备连接用的装
置,要确保其连接完好且使用得当。使用集
尘装置可降低尘屑引起的危险。
8)
不要因为频繁使用工具而产生的熟悉感而掉
以轻心,忽视工具的安全准则。某个粗心的
动作可能在瞬间导致严重的伤害。
1 / 1

DeWalt DCD991 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル
このマニュアルも適しています

他の言語で