· 高强钢打造
· 75KG高精度压力传感器
· 16位高精度角度传感器
· 刹车压力传感器和角度传感器融合算法
· 刹车弹簧与阻尼块黄金组合
1.将踏板装在搁脚板上并调整好安装孔位，使用2.5mm六角扳手将M4*10螺丝固定到搁脚板上，
为了保证使用稳定性，建议每个踏板的全部4颗螺丝都安装紧固。
2.将连接线连接到对应的安装接口处（离合压力传感器连接线需从刹车底座中间处穿过，否则安
装完踏板后可能会压到线束），利用踏板底座下的线卡卡住线束，以防止激烈驾驶时线束磨损与
缠绕。
3. 线束连接正确并将USB线插入电脑后，在MOZA Pit House中即可看到SRP踏板的工作状态。（
若设备仍为灰色或踩踏后无响应，请拔出PC端USB接口，关闭MOZA Pit House，再重新接入
USB接口并打开MOZA Pit House）
4. 可在MOZA Pit House中查看踏板的工作状态，重新设置踏板的起点、终点和行程。
左右移动调节踏板与底座孔位之间的间距，选择好螺丝孔位后再锁紧螺丝，（油门、刹车和离合的
间距调节方式一致）
使用2.5mm六角扳手逆时针转动踏板板面的螺丝并配合使用7mm开口扳手卸下背面螺母与板面
螺丝，上下移动板面根据自身需求调节板面高度，然后将螺母与螺丝拧至与板面贴合并固定
（油门、刹车和离合的板面调节方式一致）
产品介绍
01
踏板安装流程
02
踏板板面高度调节说明
04
包装清单
05
产品参数
06
踏板间距调节方法
03
User manual 使用说明书
Load Cell for the Best Control
SRP Racing Pedals
1. SRP踏板
2. 工具包：
M4*10内六角沉头螺丝x12
M8*12内六角伞头螺丝x3
M6*20内六角圆柱螺丝x2
3. Type A 转 Type B USB线
QC
PASS
03
产品保修卡
产品型号
用户姓名
通讯地址
购买日期
用户电话
经销商信息（签章）
保修期
自购机日起，基座主体，方向盘，踏板和仪表显示屏保修12个月。设备外壳、说明书、线材、螺丝、扳
手、包装等不在“一年免费保修服务”范围内，但您可以选择有偿服务。购买者在以下条件下不享受
免费保修服务：
1. 超过三包有效期的；
2. 无三包凭证及有效发票的，但能够证明该产品在三包有效期内的除外；
3. 保修凭证上的型号与维修产品型号不符或者涂改的；
4. 非本公司特约维修人员拆动造成损坏的；
5. 因不可抗力造成损坏的；
6. 未按产品使用说明书要求使用、维护、保养而造成损坏的；
保修期限鉴于产品部位、不同国家法律法规等差异，将有所不同。相关国家与区域的保修期限，请
咨询MOZA官方或购买时联系的MOZA授权经销商。
产品保修条例
产品条码
尺寸：126*180mm
正面
背面
整体材质：高强钢
颜色：黑色
刹车感应方式：压力感应+角度传感器融合算法
压力传感器最大量程：75kg
角度传感器分辨率：16位
刹车结构：弹簧+阻尼块
油门感应方式：角度传感器
离合感应方式：角度传感器
踏板间距：可调
踏板面高低：可调
踏板接口：USB直连
踏板行程软件调节：支持
踏板行程反转功能：支持
· 踏板间距可调节
· 踏板可拆卸式设计
· 兼容放地面和专业支架
· 踏板行程软件调节
离合角度传感器接口
USB接口（连电脑）
刹车压力传感器接口
刹车角度传感器接口
油门角度传感器接口
2.5mm六角扳手x1
7mm开口扳手x1
5mm六角扳手x1
· Made of high-strength steel
· High precision pressure sensor for up
to 75 KG
· 16-bit high precision angle sensor
· Braking pressure sensor and angle
sensor fusion algorithm
· Braking spring and damping block
combined
1. Place the pedals on the footrest, use a 2.5mm hexagon wrench to fix the M4*10 screws to
the footrest. It is recommended that all 4 screws of each pedal are tightened to ensure
stability.
2. Connect the wires to the corresponding ports (the connecting wire of the clutch angle
sensor needs to pass through the middle of the brake base, otherwise it may press on the
wire harness after installing the pedal) and use the wire under the pedal base to clamp
the wire harness to prevent the wiring harness is worn or tangled during intense driving.
3. You will see the status of the SRP pedal in the Pit House once the wires are connected
and the USB cable is plugged into the computer. (If it remains gray or does not respond,
please unplug the USB port on the PC, turn off the MOZA Pit House, reconnect the USB
port and turn on the MOZA Pit House)
4. You could check the working status of the pedal, reset the pedal starting point, ending
point, and pedal travel in the MOZA Pit House.
Move left and right to adjust the spacing between the pedals and the base holes, select the
screw hole and then tighten the screw. (The accelerator, brake and clutch are adjusted in
the same way)
Use a 2.5mm hexagon wrench to turn the screws on the board surface of the pedal
counterclockwise and use a 7mm open-end wrench to remove the nuts on the back and the
screws on the board, move the board up and down to adjust the height of the board
according to your needs, and then fasten the nuts and screws to the board surface. (The
accelerator, brake and clutch are adjusted in the same way)
Product Description
01
Pedal Installment
02
Instructions for adjusting the pedal board height
04
Packing Details
05
Product Parameters
06
How to adjust the pedal spacing
03
1. SRP pedal
2. Tool kit:
M4*10 socket head countersunk head x12
M8*12 hexagon socket head screw x3
M6*20 socket head cap screws x2
3. Type A to Type B USB cable
Material: high-strength steel
Color: black
Brake sensing method: pressure sensor and angle sensor fusion algorithm
Pressure sensor maximum range: 75kg
Angle sensor resolution: 16 bits
Brake structure: spring + damping block
Throttle sensing method: angle sensor
Clutch sensing method: angle sensor
Pedal spacing:adjustable
Pedal surface height: adjustable
Pedal connection port: USB
Pedal travel software adjustment: yes
Pedal travel reverse function: yes
· Adjustable pedal spacing
· Detachable pedal design
· Compatible with floor and professional
cockpit
· Pedal travel software adjustment
brackets
clutch angle sensor port
USB connection port
(connected to the computer)
brake pressure port
brake position sensor port
throttle position sensor port
2.5mm hexagon wrench x1
7mm open end wrench x1
5mm hexagon wrench x1
材质：80G书写纸
/
