Step 4
Attach the camera mount bracket to the upper case.
Mount the camera mount bracket (camera
accessory) with screws (M4 x 4 mm {5/32 inches}:
accessory) in the consideration of the bracket
direction as shown in the drawing right.
Recommended tightening torque:
1.56 N·m {1.15 lbf·ft}
Other items that are needed (not included)
Fixing screw (M4) or anchor ............................................................ 4 pcs.
IMPORTANT
• Minimum pullout strength: 196 N {44 lbf} (per 1 pc.)
• Refer to our technical information website <Control No.: C0120> for information on the mini-
mum pull-out strength.
• Select screws according to the material of the location that the camera will be mounted to.
In this case, wood screws and nails should not be used.
Ns0522-0
Printed in China
Wall Mount Bracket
Model No. WV-QWL100
Operating Instructions
• Before attempting to connect or install this product, please read these instructions carefully and
save this manual for future use.
• The external appearance and other parts shown in this manual may differ from the actual product
within the scope that will not interfere with normal use due to improvement of the product.
Preface
This product is a wall mount bracket that is designed to mount the network camera on a wall. The
network camera will be installed after attaching this product to a junction box or concrete wall, etc.
The latest information about the supported cameras
<Control No.:C0501>
Do not use this bracket except with suitable cameras.
Failure to observe this may cause a drop resulting in injury or accidents.
Refer installation work to the dealer.
Installation work requires technique and experience. Failure to observe this may cause fire, electric
shock, injury, or damage to the product.
Be sure to consult the dealer.
The screws and bolts must be tightened to the specied torque.
Failure to observe this may cause a drop resulting in injury or accidents.
Install the product securely on a wall in accordance with the installation instructions.
Failure to observe this may cause injury or accidents.
Do not rub the edges of metal parts with your hand.
Failure to observe this may cause injury.
When using this product, also read the “Precautions” described in the operating
instructions for the camera to be attached.
Precautions
Installation
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting
from failures arising out of improper installation or operation inconsistent with this
documentation.
Caution:
• Before attempting to connect or operate this
product, please read these instructions care-
fully.
Notice:
• This product is not suitable for use in loca-
tions where children are likely to be present.
• Do not install this product in locations where
ordinary persons can easily reach.
• For information about screws and other parts
required for installation, refer to the corre-
sponding section of this document.
Included Installation Instructions Specifications
In order to prevent injury, the product must be securely mounted to the wall according
to the Installation Guide of this product.
This product is designed to be used indoors.
This product is not operable outdoors. Do not expose this product to direct sunlight for hours and
do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation,
discoloration and malfunction. Keep this product away from water and moisture.
Installation area for this product
• Make sure that the installation area is strong enough to hold the total weight of the camera
assembly before installation.
• Do not mount the product on a plaster board or a wooden section because they are too weak. If
the product is unavoidably mounted on such a section, the section shall be sufficiently reinforced.
Make sure to remove this product if it will no longer be used.
Precautions for installation
Standard Accessories
Screws ..........................................................5 pcs. (of them, 1 for spare)
(M4 x 4 mm {5/32 inches}, for securing camera mount bracket)
Template ...........................................................................................1 pc.
Operating Instructions (this document) ..............................................1 pc.
Refer to the operating instructions of the camera for details on the camera installation
(including the camera mounting, cable connection and adjustment).
Step 1
Put the template (accessory) against the wall
and mark the positions of fixing screws (M4,
locally procured) and the hole through which
the cables are laid.
If cables are routed inside the wall, bore a
hole through the wall.
Drill 4 holes on the wall to secure it with M4
screws. The hole diameter shall be decided
in accordance with the specifications of the
screws and anchors to be used. When the
cables are laid inside the wall, drill a hole
through the wall for cable installation.
Step 2
When connection is performed without drilling
the wall for cable installation, cut off the notch
marked with a circle drawn with a dotted line on
the upper or lower case with a nipper for cable
installation.
IMPORTANT
• To prevent injuries and protect the cables,
finish the side cable access hole with a file
to avoid sharp edges.
Step 3
Remove the lower case of the main unit.
The case can be removed by pulling
down it while pressing the ribs
(5 places) marked with arrows.
Ambient operating temperature: –10 °C to +55 °C {14 °F to 131 °F}
Dimensions: 165 mm (W) x 140 mm (H) x 217.5 mm (D)
{6-1/2 inches (W) x 5-1/2 inches (H) x 8-9/16 inches (D)}
Mass: Approx. 650 g {1.43 lbs}
Finish: ABS resin, i-PRO white
Step 5
Attach the upper case and the chassis to the wall
and run the cables.
Attach it with four screws. Screws are not provided.
Prepare them in accordance with the camera
installation position.
Necessary screw: M4 (4 pcs.)
Minimum pull-out strength: 196 N
{44 lbf} (per 1 pc.)
Step 10
Engage the 5 hooks to mount the lower case.
Ensure the lower case and the camera mount bracket are steadily fit with each other.
“<Control No.: C****>” used in these documents should be used to search for
information on our technical information website (https://i-pro.com/global/en/
surveillance/training-support/support/technical-information) and will guide you to
the right information.
© i-PRO Co., Ltd. 2022
i-PRO Co., Ltd.
https://www.i-pro.com/
83.5 mm
{3-9/32 inches}
46 mm
{1-13/16 inches}
Upper case
Lower case
Screw
(M4 x 4 mm {5/32 inches}: accessory)
Upper case
Camera mount bracket
(camera accessory)
Chassis
Screws
(M4, locally procured)
Step 6
Connect the cables to the external I/O terminals, audio input connector, or audio output connector.
Refer to the operating instructions of the camera for descriptions of connections. Hold the camera
main body fixing part securely at connections.
Step 7
Connect the cables to the RJ45 network terminal and power supply terminal (12 V DC).
Refer to the operating instructions of the camera for descriptions of connections.
* Be sure to mount it with holding the camera main body fixing part.
Camera fixing screw
(M3, camera accessory)
Lower case
Decorative cover
(lower)
“l” mark
Arrow
Lock lever
③Ensure that the lock lever is securely inserted into the hole of the decorative cover (lower).
Note:
• WV-QDC100 (dome cover) can be also directly installed with this product. In such a case, the
decorative cover (both upper and lower) supplied with the camera is not used.
• Follow the instructions as below to remove the
decorative cover (lower).
①Rotate the lock lever by approx. 16 degrees
counterclockwise when viewing the decorative
cover (lower) from underneath (in the direction
of ← in the drawing) while pressing the lock
lever, and pull it slightly downward.
②Rotate the decorative cover (lower) more
approx. 16 degrees counterclockwise (in the
direction of ← in the drawing), and pull it out
downward.
②
③
Lock lever
①Align the “l” mark of the decorative cover
(lower) with the arrow located above the lock
lever of the camera body and insert it from
underneath by holding the decorative cover
(lower).
②Rotate the decorative cover (lower) clockwise
when looking at it from underneath by approx.
16 degrees to insert it upward.
Rotate the decorative cover clockwise by 16
degrees more to secure it.
Step 8
Mount the camera onto the camera mount bracket.
Align the lock plate with the guide of the camera mount bracket, engage the bracket with the cam-
era body while aligning the center of the bracket with the center of the camera, and rotate the cam-
era body clockwise while pressing the camera to the camera mount bracket.
Step 9
Secure the camera mount bracket to the camera
with 1 piece of the camera fixing screw
(M3, camera accessory).
Recommended tightening torque:
0.68 N·m {0.5 lbf·ft}
Lock plate
Guide
Approx. 20°
Camera main
body fixing part
Step 11
Remove the decorative cover (lower) from the decorative cover supplied with the camera.
The decorative cover is secured with 3 hooks.
* The decorative cover (upper) is not used for mounting this product.
Step 12
Decorative cover Decorative cover (lower)
Decorative cover (upper)
①
②
Lock lever
