Yamaha CinemaStation DVR-S150 ユーザーマニュアル

SERVICE MANUAL

This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.

It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already

known and understood by the users, and have therefore not been restated.

WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal

injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,

we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA

Retailer or the appointed service representative.

IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or

recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.

The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service

departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and

specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the

distributor's Service Division.

WARNING:

Static discharges can destroy expensive components. Discharge any static electricity your body may have

accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).

IMPORTANT:

Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.

IMPORTANT NOTICE

100917

SERVICE MANUAL

DVR-S150/

NX-P150

HOME THEATER SOUND SYSTEM

DVX-S150

The DVX-S150 is composed of the DVR-S150 and the NX-P150.

DVR-S150 SELF DIAGNOSIS FUNCTION (DIAG) /

. . . . . . . . . .22–43

DVR-S150 D-AMP MODULE TROUBLESHOOTING /

. . . . . . . .44

DVR-S150 AMP ADJUSTMENT /

44

DISPLAY DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

IC DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46–56

DVR-S150 BLOCK DIAGRAM . . . . . . . . . . . . . .57–59

DVR-S150 PRINTED CIRCUIT BOARD . . . . . . .60–68

NX-SW150 PRINTED CIRCUIT BOARD . . . . . . . . .69

DVR-S150 SCHEMATIC DIAGRAM . . . . . . . . . .70–79

NX-SW150 SCHEMATIC DIAGRAM . . . . . . . . . . . .80

PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81–99

REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . .100

■

CONTENTS

TO SERVICE PERSONNEL . . . . . . . . . . . . . . . . . .2–4

PREVENTION OF ELECTRO STATIC DISCHARGE . . . . . .

4

LOCALE MANAGEMENT INFORMATION . . . . . . . .5

SYSTEM COMPOSITION /

5

FRONT PANELS . . . . . . . . . . . . . . . . . . . . . . . . . . .6–7

REMOTE CONTROL PANELS . . . . . . . . . . . . . . . . . .7

REAR PANELS . . . . . . . . . . . . . . . . . . . . . . . . . . . .8–9

SPECIFICATIONS /

10–12

INTERNAL VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

DVR-S150 DISASSEMBLY PROCEDURES /

14–18

NX-SW150 DISASSEMBLY PROCEDURES /

19–20

DVR-S150 TRAY LOCK MODE /

. . . . . . . . . . . . . . . . .21

DVR-S150

NX-P150

’04.08

DVR-S150/NX-P150

2

DVR-S150

NX-P150

■ TO SERVICE PERSONNEL

1. Critical Components Information

Components having special characteristics are marked Z

and must be replaced with parts having specifications equal

to those originally installed.

2. Leakage Current Measurement (For 120V Models Only)

When service has been completed, it is imperative to verify

that all exposed conductive surfaces are properly insulated

from supply circuits.

● Meter impedance should be equivalent to 1500 ohm shunted

by 0.15µF.

AC LEAKAGE

TESTER OR

EQUIVALENT

EQUIPMENT

UNDER TEST

INSULATING

TABLE

WALL

OUTLET

● Leakage current must not exceed 0.5mA.

● Be sure to test for leakage with the AC plug in both

polarities.

WARNING: CHEMICAL CONTENT NOTICE!

The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or

plastic (where applicable) components may also contain traces of chemicals found by the California Health and

Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm.

DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR

ANY REASON WHATSOEVER!

Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes

or expose eyes to solder/flux vapor!

If you come in contact with solder or components located inside the enclosure of this product, wash your hands

before handling food.

About lead-free solder /

Among some types of lead-free solder currently available, it

is recommended to use one of the following types for the

repair work.

• Sn + Ag + Cu (tin + silver + copper)

• Sn + Cu (tin + copper)

• Sn + Zn + Bi (tin + zinc + bismuth)

Caution:

1. As the melting point temperature of the lead-free solder

is about 30°C to 40°C (50°F to 70°F) higher than that of

the lead solder, be sure to use a soldering iron suitable to

each solder.

The P.C.B.s installed in this unit are soldered using the fol-

lowing solder.

Side A

Side B

SMT REFLOW Process

MI FLOW Process

Solder Dip

DVR-S150/NX-P150

DVR-S150

NX-P150

3

WARNING: Laser Safety

This product contains a laser beam component. This

component may emit invisible, as well as visible radiation,

which may cause eye damage. To protect your eyes

and skin from laser radiation, the following precautions

must be used during servicing of the unit.

1) When testing and/or repairing any component within the

product, keep your eyes and skin more than 30 cm

away from the laser pick-up unit at all times. Do not

stare at the laser beam at any time.

2) Do not attempt to readjust, disassemble or repair the

laser pick-up, unless noted elsewhere in this manual.

3) CAUTION : Use of controls, adjustments or

performance of procedures other than those specified

herein may result in hazardous radiation exposure.

Laser Emitting conditions:

1) When the Top Cover is removed, and the STANDBY/

ON SW is turned to the "ON" position, the laser

component will emit a beam for several seconds to

detect if a disc is present. During this time (5-10 sec.)

the laser may radiate through the lens of the laser pick-

up unit. Do not attempt any servicing during this period!

If no disc is detected, the laser will stop emitting the

beam. When a disc is loaded, you will not be exposed

to any laser emissions.

2)The laser power level can be adjusted with the VR on

the pick-up PWB, however, this level has been set by

the factory prior to shipping from the factory. Do not

adjust this laser level control unless instruction is

provided elsewhere in this manual. Adjustment of this

control can increase the laser emission level from the

device.

Laser Diode Properties

Type: Semiconductor laser GaAlAs

Wave length: 650 nm (DVD)

790 nm (VCD/CD)

Output Power: 1.45 mW (DVD)

1.31 mW (VCD/CD)

Beam divergence: 60 degree

VARO! : AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE

LASER-SÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING! : OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.

BETRAKTA EJ STRÅLEN.

2. If lead solder must be used, be sure to remove lead-free

solder from each terminal section of the parts to be re-

placed and from the area around it completely before sol-

dering, or make sure that the lead-free solder and lead

solder melt together fully.

DVR-S150/NX-P150

4

DVR-S150

NX-P150

■ PREVENTION OF ELECTRO STATIC DISCHARGE

The laser diode in the traverse unit (optical pickup) may be damaged due to static electricity from clothes or the human

body. Use caution to prevent electrostatic damage when servicing or handling the laser diode.

1. Grounding for electrostatic damage prevention

Some devices, such as the DVD player, use an optical pickup (laser diode) that will be damaged by static electricity in the

working environment. Only attempt service after ensuring that all grounding procedures have been completed.

1. Worktable grounding

Put a grounded conductive material (sheet) or iron sheet on the area where the optical pickup is placed.

2. Human body grounding

Use an anti-static wrist strap to discharge the static electricity from your body.

2. Handling of the optical pickup

1. To prevent damage to the optical pickup replacement parts during transportation and before installation, both ends

of the laser diode are short-circuited. After installing the new part, remove the short circuit according to the correct

procedure in this service manual.

2. Do not use a tester to check the laser diode in the optical pickup. The power supply in the tester will damage the

laser diode.

3. Handling Precautions for the Traverse Unit (Optical Pickup)

1. Handle the traverse unit (optical pickup) gently, as it is an extremely high-precision assembly.

2. The flexible cable lines may break if an excessive force is applied to it. Use caution when handling the cable.

3. The semi-fixed resistor for laser power adjustment should not be adjusted. Do not turn the resistor.

WARNING

The use of optical instruments with this product will increase eye hazard.

Repair handling should take place as much as possible with a disc loaded inside the player.

1MΩ

Conductive material

(sheet) or steel sheet

Anti-static wrist strap

U, C, R, T, K, A, B, G, E, L models

DVD MECHANISM

BOTTOM VIEWTOP VIEW

U, C, R, T, K, A, B, G, E, L models

DVR-S150/NX-P150

DVR-S150

NX-P150

5

■ LOCALE MANAGEMENT INFORMATION

Locale Management Information : This DVD player is designed and manufactured to respond to the Locale

Management Information that is recorded on a DVD disc. If the Locale number described on the DVD disc does not

correspond to the Locale number of this DVD player, this DVD player cannot play this disc.

This product incorporates copyright

protection technology that is protected by

method claims of certain U.S. patents and

other intellectual property rights owned by

Macrovision Corporation and other rights

owners. Use of this copyright protection

technology must be authorized by

Macrovision Corporation, and is intended

for home and other limited viewing uses

only unless otherwise authorized by

Macrovision Corporation. Reverse

engineering or disassembly is prohibited.

q

w

r

w

t

r

w

y

e

t

The DVX-S150 is composed of the DVR-S150 and the NX-P150.

■ SYSTEM COMPOSITION

NX-S150

NX-C150

NX-SW150

DVR-S150

NX-P150

DVR-S150/NX-P150

6

DVR-S150

NX-P150

▼ DVR-S150

■ FRONT PANELS

B, G, E models

U, C, R, T, K, A, L models

J model

U, C, R, T, K, A, L, J models only

DVR-S150/NX-P150

DVR-S150

NX-P150

7

▼ NX-SW150

▼ DVR-S150 SI

(B, G, E models)

■ REMOTE CONTROL PANELS

▼ DVR-S150 SI

(J model)

▼ DVR-S150 SI

(U, C, R, T, K, A, L models)

▼ NX-C150 ▼ NX-S150

▼ DVR-S150 BL

(U, C, A models)

WD52690

DVR-S150/NX-P150

8

DVR-S150

NX-P150

■ REAR PANELS

▼ DVR-S150 (U, C, R, T, K, A, L models)

▼ DVR-S150 (B, G, E models)

▼ DVR-S150 (J model)

NX-S150

IMPEDANCE

NOMINAL

MAXIMUM

INPUT

6 OHMS

30 WATTS

100 WATTS

NX-C150

IMPEDANCE

NOMINAL

MAXIMUM

INPUT

6 OHMS

30 WATTS

100 WATTS

▼ NX-S150

▼ NX-C150

DVR-S150/NX-P150

DVR-S150

NX-P150

9

NX-SW150

40

▼ NX-SW150 (U, C models)

NX-SW150

40

▼ NX-SW150 (B, G, E models)

NX-SW150

40

▼ NX-SW150 (R, T, K, L models)

NX-SW150

40

▼ NX-SW150 (A model)

NX-SW150

25

▼ NX-SW150 (J model)

DVR-S150/NX-P150

10

DVR-S150

NX-P150

■ SPECIFICATIONS

AMPLIFIER SECTION /

Input Sensitivity/Impedance /

VCR, VIDEO

. . . . . . . . . . . . . . . . . . . . .

200 mV/47 kΩ

Maximum Input Signal /

VCR, VIDEO (1kHz, 0.5 % THD)

. . . . . . . . . . . . .

2.2 V

Output Level/Impedance /

(when 1 kHz, 200 mV is input)

REC OUT

. . . . . . . . . . . . . . . . . . . . . .

200 mV/1.2 kΩ

PRE OUT (SUBWOOFER/FRONT SP Small, 50Hz)

. . .

4V

Frequency Response /

REC OUT (FRONT L/R, 20 Hz to 20 kHz)

. . .

0/-1 dB

Signal to Noise Ratio (IHF-A Network) /

VCR, VIDEO (REC OUT, Input shorted, 200mV)

. . .

90 dB

Minimum RMS Output Power /

R, T, K, A, B, G, E, L, J models

FRONT L/R (6 Ω, 1 kHz, 0.9% THD)

. . . . . . . .

45 W/ch

CENTER (6 Ω, 1 kHz, 0.9% THD)

. . . . . . . . . . . .

45 W

SURROUND L/R (6 Ω, 1 kHz, 0.9% THD)

. . . .

45 W/ch

U, C models

FRONT L/R (6 Ω, 20 Hz to 20 kHz, 0.9% THD)

. . .

45 W/ch

CENTER (6 Ω, 20 Hz to 20 kHz, 0.9% THD)

. . . . . .

45 W

SURROUND L/R (6 Ω, 20 Hz to 20 kHz, 0.9% THD)

. . .

45 W/ch

Maximum Power (EIAJ) /

FRONT L/R (6 Ω, 1 kHz, 10% THD)

. . . . . . . .

55 W/ch

CENTER (6 Ω, 1 kHz, 10% THD)

. . . . . . . . . . . .

55 W

SURROUND L/R (6 Ω, 1 kHz, 10% THD)

. . . .

55 W/ch

Total Harmonic Distortion /

FRONT L/R (1 kHz, 20 W, SP OUT)

. . . . . . . .

0.05 %

VIDEO SECTION (VCR, VIDEO) /

Video Signal Type / NTSC/PAL

Video Signal Level /

Video

. . . . . . . . . . . . . . . . . . . . . . . . . . .

1 Vp-p/75 Ω

S-Video

Y

. . . . . . . . . . . . . . . . . . . . . . . . . .

1 Vp-p/75 Ω

C

. . . . . . . . . . . . . . . . . . . . . . .

0.286 Vp-p/75 Ω

Maximum Input Level /

VCR, VIDEO

. . . . . . . . . . . . . . . . . . . . . . . . .

1.5 Vp-p

Signal to Noise Ratio /

Monitor Out

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

50 dB

Frequency Response /

Monitor Out (5 Hz to 10 MHz)

Video

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

0/-3 dB

S-Video

. . . . . . . . . . . . . . . . . . . . . . . . . .

0/-3 dB

TUNER SECTION /

FM Tuning Range /

U, C models

. . . . . . . . . . . . . . . . . .

87.5 to 107.9 MHz

T, K, A, B, G, E models

. . . . . . .

87.50 to 108.00 MHz

R, L models

. . . . . . . . . . . . . . . . . .

87.5 to 108.0 MHz

87.50 to 108.00 MHz

J model

. . . . . . . . . . . . . . . . . . . . . .

76.0 to 90.0 MHz

AM Tuning Range /

U, C models

. . . . . . . . . . . . . . . . . . .

530 to 1710 kHz

DVR-S150

T, K, A, B, G, E, J models

. . . . . . . .

531 to 1611 kHz

R, L models

. . . . . . . . . . . . . . . . . . .

530 to 1710 kHz

531 to 1611 kHz

DVD SECTION /

Output Level /

REC OUT

DVD/VIDEO, CD/CD-DA (1 kHz, 0 dB)

. . . . .

2 ± 0.3 V

Video Output / 1 Vp-p/75 Ω

Y Output/S-Video Output /

1 Vp-p/75 Ω

C Output/S-Video Output /

U, C, R, J models

. . . . . . . . . . . . . . . .

0.286 Vp-p/75 Ω

K, L, A, B, G, E models

. . . . . . . . . . . . .

0.3 Vp-p/75 Ω

Y Output/Component Video Output /

U, C, R, T, K, A, B, G, E, L models

. . . .

1.0 Vp-p/75 Ω

Pb Output/Component Video Output /

U, C, R, T, K, A, B, G, E, L models

. . . .

0.7 Vp-p/75 Ω

Pr Output/Component Video Output /

U, C, R, T, K, A, B, G, E, L models

. . . .

0.7 Vp-p/75 Ω

GENERAL /

Power Supply /

U, C models

. . . . . . . . . . . . . . . . . . . .

AC 120 V, 60 Hz

R model

. . . . . . . . . . . . . . . . . . .

AC 110–120 V, 50 Hz

T model

. . . . . . . . . . . . . . . . . . . . . . .

AC 220 V, 50 Hz

K model

. . . . . . . . . . . . . . . . . . . . . . .

AC 220 V, 60 Hz

A model

. . . . . . . . . . . . . . . . . . . . . . .

AC 240 V, 50 Hz

B, G, E models

. . . . . . . . . . . . . . . . .

AC 230 V, 50 Hz

L model

. . . . . . . . . . . . . . . . . . .

AC 220–240 V, 50 Hz

J model

. . . . . . . . . . . . . . . . . . . .

AC 100 V, 50/60 Hz

Power Consumption /

J model

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

95 W

U, C, R, T, K, A, B, G, E, L models

. . . . . . . . . .

85 W

Standby Power Consumption /

U, C, T, K, A, B, G, E, J models

. . . . . . . . . . . . .

0.4 W

R, L models

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

0.5 W

Dimensions (W x H x D) /

. . . . . . . . . . . . . . . . . . . .

360 x 75 x 370.2 mm

(14-3/16" x 2-15/16" x 14-9/16")

Weight / 6.4 kg (14 lbs 1 oz)

Finish /

. . . . . . . . . .

Black color (U, C, A models)

Silver color (

U, C, R, T, K, A, B, G, E, L, J models

)

White color (

U, R, K, L, J models

)

Accessories /

. . . . . . . . . . . . .

Remote Control x 1

Battery (size "UM-3", "R06") x 2

Indoor FM antenna x 1

AM loop antenna x 1

Video Pin Cable (1.5 m) x 1

Speaker Cable (Front, Center: 5 m) x 3

Speaker Cable (Surround: 15 m) x 2

Optimizer Microphone (6 m) x 1

* Specifications subject to change without notice.

U ....... USA model

C ....... Canadian model

R ....... General model

T ....... Chinese model

K ....... Korean model

A ....... Australian model

B ....... British model

G ....... European model

E ....... South European model

L ....... Singapore model

J ....... Japanese model

DVR-S150/NX-P150

DVR-S150

NX-P150

11

NX-P150

● NX-S150

Type / . . . . . . . . . . . .

Full Range Acoustic Suspension

Magnetic Shielding Type

Driver /

. 5 cm (2”) Cone Magnetic Shielding Type x 2

Frequency Response /

100 Hz to 25 kHz

Impedance / . . . . . . . . . . . . . . . . . . 6 Ω

Nominal Input / 45 W

Maximum Input / 100 W

Sensitivity / . . . . . . . . 86 dB/2.83 V/m

Input Terminal / . . . . . . . . . . . . . . Push Type

Dimensions (W x H x D) /

. . . . . . . . . . . . . 72 mm x 170 mm x 108 mm

(2-13/16” x 6-11/16” x 4-1/4”)

Weight / . . . . . . . . . . . . . . . . . . . . . . 0.9 kg (2 lbs.)

Finish / . . . . . . . . . . . . . Black

(U, C, A models)

Silver color (U, C, R, T, K, A, B, G, E, L, J models)

Accessories / Nonskid Pads x 16

Mounting Bracket x 4, Screws x 4

Appropriate Speaker Stand /

. . . SPS-80

Appropriate Speaker Bracket / . . . SPM-8S

● NX-SW150

Type / . . . . . Advanced Yamaha Active Servo Technology

Output Power / 50 W (100 Hz, 5 Ω, 10 % THD)

Dynamic Power / 100 W, 5 Ω

Input Impedance / INPUT (PJ): 12 kΩ

Frequency Response / 30 Hz to 200 Hz

Driver / 16 cm (6-1/2”) cone

Magnetic Shielding Type

Input Section /

INPUT . . . . . . . . . . . . . . . . . . . . . . . . . RCA Pin Jack

SYSTEM CONNECTOR . . . . . . . . . . Mono Mini Jack

Power Supply /

U, C models . . . . . . . . . . . . . . . . . . . AC 120 V, 60 Hz

R, T, K, L models . . AC 110-120/220-240 V, 50/60 Hz

A model . . . . . . . . . . . . . . . . . . . . . . AC 240 V, 50 Hz

B, G, E models . . . . . . . . . . . . . . . . AC 230 V, 50 Hz

J model . . . . . . . . . . . . . . . . . . . . AC 100 V, 50/60 Hz

Power Consumption /

U, C, R, T, K, A, B, G, E, L models . . . . . . . . . . 40 W

J model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 W

Dimensions (W x H x D) /

. . . . . . . . . . . . 200 mm x 365 mm x 390 mm

(7-7/8” x 14-7/20” x 15-5/16”)

Weight / . . . . . . . . . . . . . . . . 8.4 kg (18 lbs. 8 oz.)

Finish / . . . . . . . . . . . . . Black

(U, C, A models)

Silver color (U, C, R, T, K, A, B, G, E, L, J models)

Accessories / Subwoofer Cable (5 m) x 1

System Control Cable (5 m) x 1

Nonskid Pad x 4

* Specifications subject to change without notice.

● NX-C150

Type / . . . . . . . . . . . .

Full Range Acoustic Suspension

Magnetic Shielding Type

Driver /

. 5 cm (2”) Cone Magnetic Shielding Type x 2

Frequency Response /

100 Hz to 25 kHz

Impedance / . . . . . . . . . . . . . . . . . . 6 Ω

Nominal Input / 45 W

Maximum Input / 100 W

Sensitivity / . . . . . . . . 86 dB/2.83 V/m

Input Terminal / . . . . . . . . . . . . . . Push Type

Dimensions (W x H x D) /

. . . . . . . . . . . . . 300 mm x 72 mm x 105 mm

(11-13/16” x 2-13/16” x 4-1/8”)

Weight / . . . . . . . . . . . . . . . . . 1.1 kg (2 lbs. 6 oz.)

Finish / . . . . . . . . . . . . . Black

(U, C, A models)

Silver color (U, C, R, T, K, A, B, G, E, L, J models)

Accessories / Fasteners x 2

U ....... USA model

C ....... Canadian model

R ....... General model

T ....... Chinese model

K ....... Korean model

A ....... Australian model

B ....... British model

G ....... European model

E ....... South European model

L ....... Singapore model

J ....... Japanese model

DVR-S150/NX-P150

12

DVR-S150

NX-P150

Unit : mm (inch)

300 (11-13/16") 105 (4-1/8")

72 (2-13/16")

72 (2-13/16") 108 (4-1/4")

170 (6-11/16")

● NX-S150

● NX-C150

● DVR-S150

200 (7-7/8") 390 (15-5/16")

365 (14-3/8")

DIMENSIONS

● NX-SW150

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic” and the double-D symbol are trademarks of

Dolby Laboratories.

V

“DTS” and “DTS Digital Surround” are registered trademarks of

Digital Theater Systems, Inc.

360 (14-3/16")

370.2 (14-9/16")

75

(2-15/16")

DVR-S150/NX-P150

DVR-S150

NX-P150

13

■ INTERNAL VIEW

q SUB (3) P.C.B.

w DVD P.C.B.

e AM/FM TUNER

r MAIN (1) P.C.B.

t D-AMP MODULE

y DIGITAL P.C.B.

u DVD MECHANISM

i MAIN (2) P.C.B.

o SUB (1) P.C.B.

!0 MAIN (3) P.C.B.

!1 POWER TRANSFORMER

wq e r

t

u !0o !1y i

wq

e

▼ DVR-S150

▼ NX-SW150

q MAIN (2) P.C.B.

w MAIN (1) P.C.B.

e POWER TRANSFORMER

DVR-S150/NX-P150

14

DVR-S150

NX-P150

■ DVR-S150 DISASSEMBLY PROCEDURES

(Remove parts in disassembly order as numbered.)

q

w

1. Removal of Side Cover L/R

a. Remove 1 screw ( q

) in Fig. 1.

b. Lift the Side Cover L at the rear and move it rear-ward

slantingly.

c. Remove 1 screw ( w

) in Fig. 1.

d. Lift the Side Cover R at the rear and move it rear-ward

slantingly.

e

r

2. Removal of Bottom Cover

a. Remove 2 screws ( e ) in Fig. 2.

b. Spread soft cloth and place this unit upside down on it.

c. Remove 4 screws ( r ) in Fig. 2.

d.

Release 1 hook and remove the Bottom Cover

toward

the Front Panel side in Fig. 2.

Fig. 1

Fig. 2

wq

e

r

● Bottom view

DVR-S150/NX-P150

DVR-S150

NX-P150

15

●

● HOW TO MANUALLY EJECT THE TRAY

a. Remove the Side Cover L/R.

b. Remove the Bottom Cover.

c. Move the slider in the direction indicated.

d. Gently pull the tray out.

t

y u

Fig. 4

Fig. 3

3. Removal of Top Unit

a. Remove 1 screw ( t ) in Fig. 3.

b.

Remove connectors CB221, CB222 and CB278 in Fig. 3.

c. Turn this unit again to set it upside up.

d. Remove 6 screws ( y ) and 2 screws ( u ) in Fig. 4.

e. Remove the Top Unit

.

y

t

uyy

DVR-S150/NX-P150

16

DVR-S150

NX-P150

i

o

!0

!1

4. Removal of DVD Mechanism

a. Remove 2 screws ( i

) and then remove the Top

Frame in Fig. 5.

b. Remove 3 screws ( o ) in Fig. 5.

c. Remove 2 screws ( !0 ) in Fig. 5. (G, B, E models only)

d. Remove the DVD support and the DVD P.C.B. in Fig. 5.

e. Remove connectors 1601, 1603, 1615, 1618, 1619 and

1620 in Fig. 6

.

f. Remove connector CB3 in Fig. 7

.

g. Remove 4 screws ( !1 ) and then remove the DVD

Mechanism in Fig. 7.

Fig. 5

Fig. 6

Fig. 7

!0

i

o

!1

DVR-S150/NX-P150

DVR-S150

NX-P150

17

!2

!4

!3

!5

!6

!2

!3

!4 !5

!6

5. Removal of DIGITAL P.C.B.

a. Remove connectors CB1, CB3 and CB5 in Fig. 8.

b. Remove 4 screws ( !2 ) and then remove the DIGITAL

P.C.B. in Fig. 8.

6. Removal of D-Amp Module

Remove 5 screws ( !3

) and then remove the D-Amp

Modules in Fig. 8.

7. Removal of MAIN (3) P.C.B.

a. Remove connector CB224 in Fig. 8

.

b. Remove 3 screws ( !4 ) and 1 push rivet ( !5 ) and then

remove the MAIN (3) P.C.B. in Fig. 8.

8. Removal of AM/FM Tuner

a. Remove connector CB121 in Fig. 8.

b. Remove 2 screws ( !6

) and then remove the AM/FM

Tuner in Fig. 8.

Fig. 8

DVR-S150/NX-P150

18

DVR-S150

NX-P150

!7

!8

!9

@0 @1

@2

@3 @4

@5

9. Removal of MAIN (2) & SUB (1) P.C.B.

a. Remove 2 screws ( ! 7

) in Fig. 9.

b. Remove 3 screws ( !8

) and then remove the Shield in

Fig. 9.

c. Remove 2 screws ( !9 ) in Fig. 9.

d. Remove 2 screws ( @ 0

) and 1 screw ( @1 ) in Fig. 9.

e. Remove connectors CB2, CB124, CB275, CB276 and

CB277 in Fig. 9

.

f. Remove the MAIN (2) & SUB (1) P.C.B. in Fig. 9.

10. Removal of MAIN (1) & SUB (3) P.C.B.

a. Remove 2 screws ( @2

) and then remove the Power

Cable Support in Fig. 9.

b. Remove 3 screws ( @3 ) and 2 screws ( @4 ) in Fig. 9.

c. Remove connector CB17 in Fig. 9

.

d. Remove 3 screws ( @ 5 ) in Fig. 9.

e. Remove the MAIN (1) & SUB (3) P.C.B. with the Rear

Panel attached to it in Fig. 9.

Fig. 9

!9

@5

@3

!8

@0

@1

@4

@3

!7

@2

DVR-S150/NX-P150

DVR-S150

NX-P150

19

1. Removal of Front Grille

The Front Grille is fixed to the cabinet with dowels

at 6 locations. As a screwdriver (for slotted head

screw) is used for removal, use special care not to

cause damage to the cabinet.

a. Using the screwdriver inserted in the gap between

the Front Grille and the cabinet (bottom side first),

push up the Front Grille.

b. Remove the Front Grille by lifting it up.

* When installing the Front Grille, apply quick-drying

bond to the dowels and then fit them into dowel holes

for secure installation. (The Front Grille will come off

easily if its dowels are fitted into dowel holes only.)

2. Removal of Rear Panel

Remove 14 screws ( q ) in Fig. 2.

* Arrow marks ( ) are printed to identify the screws to

be removed.

* When assembling the Rear Panel, check to ensure that

the packing is not damaged so as to prevent air leakage

from occurring.

■ NX-SW150 DISASSEMBLY PROCEDURES

(Remove parts in disassembly order as numbered.)

q

Fig. 1 Fig. 2

q

DVR-S150/NX-P150

20

DVR-S150

NX-P150

When checking the P.C.B.:

Turn on the power to NX-SW150 according to the following

procedure.

a. Short between the terminals of RY2 (relay).

b. Connect the power cable to the AC power outlet.

Short between these terminals for the P.C.B. check.

Short

ページを読み込んでいます...

Yamaha CinemaStation DVR-S150, CinemaStation NX-P150, DVX-S150 ユーザーマニュアル

関連論文

その他の書類