Denon DVD-2930 ユーザーマニュアル

SERVICE MANUAL

MODEL

DVD-2930/2930CI

DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER

For U.S.A., Canada, Europe,

Asia, China & Japan model

X0273 V.03 DE/CDM 0609

Some illustrations using in this service manual are

slightly different from the actual set.

Please use this service manual with referring to the

operating instructions without fail.

For purposes of improvement, specifications and

design are subject to change without notice.

TOKYO, JAPAN

Denon Brand Company, D&M Holdings Inc.

Ver. 3

Please refer to the

MODIFICATION NOTICE.

3

2

DVD-2930/2930CI

Please heed the points listed below during servicing and inspection.

Heed the cautions!

Spots requiring particular attention when servicing, such as

the cabinet, parts, chassis, etc., have cautions indicated on

labels or seals. Be sure to heed these cautions and the cau-

tions indicated in the handling instructions.

Caution concerning electric shock!

(1) An AC voltage is impressed on this set, so touching inter-

nal metal parts when the set is energized could cause

electric shock. Take care to avoid electric shock, by for ex-

ample using an isolating transformer and gloves when

servicing while the set is energized, unplugging the power

cord when replacing parts, etc.

(2)There are high voltage parts inside. Handle with extra care

when the set is energized.

Caution concerning disassembly and assembly!

Though great care is taken when manufacturing parts from

sheet metal, there may in some rare cases be burrs on the

edges of parts which could cause injury if fingers are moved

across them. Use gloves to protect your hands.

Only use designated parts!

The set's parts have specific safety properties (fire resis-

tance, voltage resistance, etc.). For replacement parts, be

sure to use parts which have the same properties. In particu-

lar, for the important safety parts that are marked ! on wiring

diagrams and parts lists, be sure to use the designated parts.

Be sure to mount parts and arrange the

wires as they were originally!

For safety reasons, some parts use tape, tubes or other insu-

lating materials, and some parts are mounted away from the

surface of printed circuit boards. Care is also taken with the

positions of the wires inside and clamps are used to keep

wires away from heating and high voltage parts, so be sure to

set everything back as it was originally.

Inspect for safety after servicing!

Check that all screws, parts and wires removed or discon-

nected for servicing have been put back in their original posi-

tions, inspect that no parts around the area that has been

serviced have been negatively affected, conduct an insulation

check on the external metal connectors and between the

blades of the power plug, and otherwise check that safety is

ensured.

(Insulation check procedure)

Unplug the power cord from the power outlet, disconnect the

antenna, plugs, etc., and turn the power switch on. Using a

500V insulation resistance tester, check that the insulation re-

sistance between the terminals of the power plug and the ex-

ternally exposed metal parts (antenna terminal, headphones

terminal, microphone terminal, input terminal, etc.) is 1M or

greater. If it is less, the set must be inspected and repaired.

Concerning important safety parts

Many of the electric and structural parts used in the set have

special safety properties. In most cases these properties are

difficult to distinguish by sight, and using replacement parts

with higher ratings (rated power and withstand voltage) does

not necessarily guarantee that safety performance will be pre-

served. Parts with safety properties are indicated as shown

below on the wiring diagrams and parts lists is this service

manual. Be sure to replace them with parts with the designat-

ed part number.

(1) Schematic diagrams ... Indicated by the ! mark.

(2) Parts lists ... Indicated by the ! mark.

Using parts other than the designated parts

could result in electric shock, fires or other

dangerous situations.

SAFETY PRECAUTIONS

The following check should be performed for the continued protection of the customer and service technician.

LEAKAGE CURRENT CHECK

Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis

resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power

cord is less than 460 kohms, the unit is defective.

LASER RADIATION

Do not stare into beam or view directly with optical instruments, class 3A laser product.

CAUTION

3

DVD-2930/2930CI

WIRE ARRANGEMENT

If wire bundles are untied or moved to perform adjustment or

parts replacement etc., be sure to rearrange them neatly as

they were originally bundled or placed afterward.

Otherwise, incorrect arrangement can be a cause of noise

generation.

Wire arrangement viewed from the top

DVD2930CIE3

DVD2930JP

DVD2930E2/E2A/E1C

4

DVD-2930/2930CI

No. Part Name Q'ty Material

m • 1 Top cover 1 SECC+PVC

m • 2 Inner cover 1 SECC

m • 3 Mecha cover (only E3) 1 SECC

m • 4 Support bracket 1 SECC

m • 5 Chassis & the others 1 SECC

m • 6 Display Bracket (only E3) 1 SECC

m • 7 Spring 2 SUS304

m • 8 Front panel 1 A6063SS

m the othes -

m (Metals) totals 5,383g

No. Part Name Q'ty Material

s • 1 Screw 3X6 CBTS(S)-B SW

s • 2 Screw 4X8 3P SWELLING 9 SW

s • 3 Screw 3X8 CFTS(S) SW

s • 4 Screw 2.6X8 CBTS(S) SW

s • 5 Screw 3X8 CBTS(S)-Z SW

s • 6 Screw 3X8 CBTS(P)-B SW

s • 7 M3 nut (RS-232C) 2 SW

s • 8 Screw 3X8 CBS-Z SW

s • 9 Screw 3X6 CFS

s • 10 Screw FIXING

s • 11 Screw 3X8 CPTS(S) 1

s • 12 Screw 3X10 CFTS(P) 2 SW

s • 13 Screw 3X10 Special(P) 2 SW

s the othes -

s (Screws) totals 69g

Total Weight 7,522g

Recycle Weight 5,714g

Abandonment Weight 1,808g

DISASSEMBLY

(Follow the procedure bellow in reverse order when

reassembling.)

Disassembly and abandonment

(1) Disassembly of a set

It decomposes according to a work procedure 1.~11.

clause.

(2) Judgment of use parts

It classifies according to the discernment signs in a figure

(c, m, s, p, etc.).

(3) Abandonment of parts

Each part article is discarded according to the

specification abandonment method of each

self-governing body.

The parts of mark show that it shall be remove.

No. Part Name Q'ty Material

c • 1 Loader Panel ass'y 1 -

c • 2 DVD mechanism ass'y 1 -

c • 3 Power P.W.B. ass'y 1 -

c • 4 Ac inlet 1 -

c • 5 Ferrite core & 3P VH wire 1 -

c • 6 Block of Video P.W.B. 1 -

c • 7 Block of Audio P.W.B. 1 -

c • 8 A.Power P.W.B. ass'y 1 -

c • 9 M.Support P.W.B. 1 -

c • 10 Display P.W.B. ass'y 1 -

c • 11 P.SW-1 P.W.B. ass'y 1 -

c • 12 P.SW-2 P.W.B. ass'y 1 -

c • 13 Power knob(SUB) ass'y 1 -

c Wire ( the othes ) -

c (Complex) totals 1,808g

No. Part Name Q'ty Material

p • 1 Heat sheet 1 Silicon

p • 2 Foot ass'y 4 ABS+CR

p • 3 PWB support 2 PA66

p • 4 Rubber 2 CR

Gasket ( only E3 ) 2 PE

p • 5 Gasket ( only E3 ) 4 PE

p • 6 Inner panel 1 ABS

p • 7 Part of inner panel 1 ABS

p • 8 Blind ass'y 1 PVC+PE

p • 9 Rubber sheet 2 CR

p the othes -

p (Plastics) totals 262g

The parts of mark show that it shall be remove at the disassembly and the abandonment

Part Name Dimensions Ref.No. Unit No. Q'ty

CE04W2G470MC (KMG)

16.0 X h31.5mm

C-904 c • 3 Power P.W.B. ass'y (GU-3730-2) 1

CE04W1E102MC J30(KY)

10.0 X h30.0mm

C-913 c • 3 Power P.W.B. ass'y (GU-3730-2) 1

CE04W0J562MC(KY)K35

12.5 X h35.0mm

C-916, C-917 c • 3 Power P.W.B. ass'y (GU-3730-2) 2

5

DVD-2930/2930CI

1. Top cover & Inner cover

1.1. Top cover

(1) Remove 2 screws (s • 1) on the rear side and

9 screws (s • 2) on the top and the both sides.

(2) Widen the Top cover (m • 1) a little laterally, then detach

it with sliding.

1.2. Inner cover

(1) Remove 4 screws (s • 3) on the top side.

(2) Detach Inner cover (m • 2).

s • 2

s • 3

s • 1

m • 1: Top cover

m • 2: Inner cover

s • 2

http://getMANUAL.com

6

DVD-2930/2930CI

2. DVD mechanism ass'y

2.1. When the Disc tray can be ejected electrically.

(1) Switch on, and press [OPEN/CLOSE] button to open the

Disc tray.

(2) Detach the Loader panel ass'y (c • 1) by lifting.

(3) Close the Disc tray.

(4) Remove 4 screws (s • 4) and 2 screws (s • 5) on the top

side.

Remove 5 top screws (s • 6) and 2 side screws (s • 1),

then detach the Mecha cover (m • 3) (only E3).

(5) Disconnect [CX171] [CX331] [CX044] [CX211] from the

MAIN P.W.B. (GU-3729-1).

(6) Take the DVD mechanism ass'y (c • 2) off.

2.2. When the Disc tray cannot be ejected electrically.

(1) Insert a driver into the left hole, and push the Plate Gear

of the DVD Mechanism, to open the Disc Tray.

(Arrow direction)

(2) The same steps described on 2-1. (2)~(6).

s • 1

s • 6

s • 1

m • 3: Mecha cover (only E3)

c • 2: DVD mechanism ass’y

c • 1: Loader panel ass’y

s • 4

s • 5

7

DVD-2930/2930CI

3. Front panel sub ass'y

(1) Disconnect the wire [CX031] [CX025] connecting From

the Front panel sub ass'y (a • 1).

(2) Remove 2 top screws (s • 3) and 4 bottom screws (s • 1),

then detach the Front panel sub ass'y.

s •3

s •1

a • 1: Front panel sub ass’y

8

DVD-2930/2930CI

4. Power P.W.B. ass'y etc.

4.1. Power P.W.B. ass'y

(1) Remove 1 screw (s • 6) and 2 nut (s • 7) on the rear side.

(2) Remove 4 side screws (s • 8) and 4 top screws (s • 3).

(3) Disconnect the wire [CX132] [CX054] [CX024] [CX071]

[CX033] connecting Power P.W.B. ass'y (c • 3).

(4) Detach the Power P.W.B. ass'y (c • 3).

Thing to do abandonment based on WEEE directive

detaching E-Capacitor of C904, C913, C916, C917 when

abandoning Power P.W.B. ass'y (c • 3).

4.2. AC INLET

(1) Remove 2 rear screws (s • 3).

(2) Disconnect the STO terminals from AC inlet (c • 4).

(3) Detach the AC inlet (c • 4).

4.3. Ferrite core & 3P VH wire

(1) Cut 3 clamper on the left side of the chassis.

(2) Detach the Ferrite core & 3P VH wire (c • 5).

C916, 917: 12.5 x h35.0mm: 5600uF/6.3V

C913: 10 x h30.0mm: 1000uF/25V

c • 3: Power P.W.B. ass’y

s • 5

C904: 16 x h31.5mm: 47uF/400V

s • 8

c • 4: AC inlet

s • 3

s • 6

s • 7

c • 5: Ferrite core & 3P VH wire

Clamper

9

DVD-2930/2930CI

5. Block of Video P.W.B.

5.1. Support bracket

(1) Remove 2 rear screws (s • 1) and 2 side screws (s • 1)

and 3 top screws (s • 9).

(2) Disconnect [CY041] [CY131] from the D.Video P.W.B.

ass'y (GU-3748). (only E2 & E1C)

(3) Take the Support bracket (m • 4) off.

(4) Take the Heat sheet (p • 1) off.

5.2. Block of Video P.W.B.

(1) Remove 4 screws (s • 1) and 5 (JP: 6, E2&E1C: 7) screws

(s • 10) and 1 screw (s • 11) on the rear side and 2 screws

(s • 5) on the top side.

(2) Take the Block of Video P.W.B. (GU-3729-2/GU-3730-6

/GU-3730/GU-3730-8/GU-3748) (c • 6) off.

m • 4: Support bracket

s • 9

s • 1

p • 1: Heat sheet

s • 5

c • 6: Block of Video P.W.B. ass’y

s • 1

s • 11

s • 10

(only Japan)

s • 10 (only Europe)

10

DVD-2930/2930CI

6. Block of Audio P.W.B.

6.1. A.Power P.W.B.ass'y

(1) Remove 4 screws (s • 5) on the top side.

(2) Disconnect the wire [CX034] connecting A.Power P.W.B.

ass'y (c • 8).

(3) Detach the A.Power P.W.B. ass'y (c • 8).

6.2. Block of Audio P.W.B.

(1) Remove 2 screws (s • 1) and 6 screws (s • 10) on the rear

side and 4 screws (s • 5) on the top side.

(2) Detach the Block of Audio P.W.B. (c • 7).

6.3. Etc.

(1) Detach the PWB support (p • 3) off.

(2) Detach the M.Support P.W.B. (c • 9) off.

7. Foot ass'y

(1) Remove 4 bottom screws (s • 5).

(2) Take the Foot ass'y (p • 4) off.

(3) Take the Rubber (p • 5) off. (E3: Gasket)

s • 5

c • 7: Block of Audio P.W.B.

s • 1

s • 10

s • 5

c • 8: A.Power P.W.B. ass’y

p • 3: PWB support

c • 9: M.Support P.W.B.

s • 10

s • 1

m • 5: Chassis & Bottom cover & Rear cover

p • 4: Foot ass’y

p • 5: Rubber (E3: Gasket)

11

DVD-2930/2930CI

8. Parts on Front panel sub ass'y (a • 1)

8.1. Display Bracket (only E3)

(1) Remove 4 screws (s • 12).

(2) Take the Display Bracket (m • 6) off.

8.2. P.SW-2 P.W.B. ass'y

(1) Remove 4 screws (s • 6).

(2) Disconnect [CY052].

(3) Take the P.SW-2 P.W.B. ass'y (c • 12) off.

(4) Take the Power knob (SUB) ass'y (c • 13) off.

8.3. P.SW-1 P.W.B. ass'y

(1) Remove 2 screws (s • 12).

(2) Take the P.SW-1 P.W.B. ass'y (c • 12) off.

8.4. Display P.W.B. ass'y

(1) Remove 6 screws (s • 6).

(2) Take the Display P.W.B. ass'y (c •10) off. 8-5.Blind ass'y

8.5. Blind ass'y

(1) Remove 2 screws (s • 8).

(2) Take the 2 Springs (m • 7) and the Blind ass'y (p • 8) off.

8.6. Inner panel

(1) Detach 4 top hooks and 4 rear hooks.

(2) Take the Inner panel (p • 6) off.

8.7. Front panel

(1) Detach the Part of Inner panel (p • 7) and 2 rubber sheets

(p • 9) by minus(-) driver or etc..

p • 9: Rubber sheet

m • 8: Front panelm • 8: Front panel

p • 7: Part of Inner panel

p • 8: Blind ass’y

m • 7: Spring

c • 10: Display P.W.B. ass’y

s • 6

s • 13

m • 6: Display Bracket (only E3)

p • 5: Gasket (only E3)

s • 12

s • 6

c • 12: P.SW-2 P.W.B. ass’y

c • 11: P.SW-1 P.W.B. ass’y

c • 13: Power knob (SUB) ass’y

p • 6: Inner panel

s • 12

12

DVD-2930/2930CI

DIAGNOSTICS OF OPTICAL PICKUP

AND REPLACING TRAVERSE UNIT

Make failure diagnostics of the Optical Pickup as follows.

If the laser drive current (Iop) becomes more than 1.5 times of

the initial value, the Optical Pickup should be replaced.

The laser drive current initial value is checked by "Iop checked

Method" of next page.

In case of replacing the Pickup, change the whole part of the

Traverse Unit.

No mechanical adjustment is necessary after the replace-

ment.

Laser drive current initial value:

FL Display The display part of 13 digits)

Disc no read, unsteady playback, etc.

Laser drive current (Iop) check

HF wave form check

(Refer to WAVE FORMS)

Traverse Unit replacing

Laser current (Iop) memorizing after replacement

Present value exceeds the ini-

tial value by 1.5 times

CD:

DVD:

13

DVD-2930/2930CI

1. Iop checked Method

Select the laser ON/OFF (CD/DVD) mode of the test mode,

and check the lop value of DVD laser or CD laser.

(See page 16 for test mode.)

1.1. DVD laser current check

(1) Press the SKIP REV or SKIP FWD button to display the

laser current value, and then select T22.

(2) Check the current value of Iop (nnnn).

( : Off, DVD laser, Initial value: mm.mm [mA],

Current value: nn.nn [mA])

1.2. CD Laser current check

(1) Press the SKIP REV or SKIP FWD button to display the

laser current value, and then select T21.

(2) Check the current value of Iop (nnnn).

( : Off, CD laser, Initial value: mm.mm [mA],

Current value: nn.nn [mA])

2. Note for Handling the Laser Pick-Up

The protection for the damage of laser diode.

If you want to change the optical device unit from any other

units, you must keep the following.

(1) It should be done at the desk already took measures the

static electricity in care of removing the OPU's (Optical

device unit) connector cable.

(2) Workers should be put on the "Earth Band".

(3) It should be done to add the solder to the short land to

prevent the broken Laser diode before removing the 24P

FFC cable.

(4) Don't touch OPU's connector parts carelessly.

3. Replacement of the Laser Pick-up

(Traverse Unit)

Check the Iop (Laser drive current)

If the present Iop (current) value exceeds.+150% of the ini-

tial value, replace the Traverse unit (Laser Pick-up) with a

new one.

FL Display The display part of 13 digits)

14

DVD-2930/2930CI

4. Rewriting the default value of the laser

current

To rewrite the default value of the laser current, press the

PLAY button for at least 5 seconds while the CD or DVD la-

ser current is displayed, then press the SKIP FWD or SKIP

REV button to select T23. (For details, see "Iop checked

Method" on page 13.)

If the PLAY button is pressed while T23 is displayed, the

current value is displayed at "mmmm" and stored in the EE-

PROM.

5. Resetting the accumulated laser on time

To clear the accumulated laser on time, press the PLAY but-

ton while the accumulated laser on time is displayed (TB1,

TB2 : For details, see "Test Mode" on page 16.) until " " ap-

pears at the fourth position, then press the SKIP FWD or

SKIP REV button to select TB3.

If the PLAY button is pressed while TB3 is displayed, the

accumulated laser on time of CD and DVD is cleared.

When TB1 or TB2 is selected with the SKIP FWD or SKIP

REV button, "nnnnnnn" is displayed as 0 so you can check.

( : Off, Y 1:CD, 2:DVD, nnnnnnn Hour [h])

FL Display The display part of 13 digits)

2

15

DVD-2930/2930CI

SERVICE MODE

1. Aging Mode

(1) preparation

(a) Equipment used: Any one of DVD Karaoke Disc (containing more than 10 titles).

(b) Unit setting : No spec other than the following procedure (Aging mode).

At the tray open status, press the “POWER” button to turn on the power while pressing the “PLAY” and “OPEN/CLOSE” buttons

for DVD operation simultaneously. mark on the FL lights, and the unit is set to the heat run mode.

(2) procedure

(a) According the above, set to the aging mode.

(b) Set a DVD Karaoke disc to the tray and press the “PLAY” button once. mark on the FL blinks, and aging operation (after

playback title-1 and title-10 of the disc, the tray open/close is made automatically, then playback the title-1 again) starts.

This aging operation continues automatically until it is stopped or it stops caused by an error. In case of some error in DVD, the

following error messages are displayed on the FL.

2. Initial Setting Mode

(1) Preparation

(a) Equipment used: None

(b) Unit setting: No spec other than the following procedure.

(2) Procedure

(a) Initialize the DVD player when µcom, peripheral parts of µcom, or Main P.W.B. has been replaced in servicing.

(b) Carry out the following to restore factory setting mode.

At the player stop condition, press 2 buttons for DVD operation (“PLAY” and “ SKIP FWD”) until “INITIALIZE” appears

and disappears in the FL.

(“Initialized” appears and disappears on the TV screen.)

(c) All user setting will be lost and its factory setting will be restored when this initialization is made. Be sure to memorize your setting

for restoring again after the initialization.

3. µcom Firm Check Mode

(1) Preparation

(a) Equipment used: None

(b) Unit setting: No spec other than the following procedure.

(2) Procedure

(a) Press the “POWER” button to turn on the power while pressing the “PLAY” and “OPEN/CLOSE” buttons for DVD operation si-

multaneously.

(b) DVD µcom and other µcom firm check mode.

This mode is for displaying the status of each µcom employed.

Push remote contraller “3265”.

DVD µcom firm: Press the “MENU” button or “PUSH ENTER” button.

Each time the “MENU” button on the remote control unit or “PUSH ENTER” button is pressed, µcom firm is displayed one

after another.

Ex.: [BE 8283, MAKE DAY 522, DSP 8250]

No. Error contents FL display

1 Tray Error ERROR 01

2 Bad Disc ERROR 02

3 Search Error ERROR 03

4 Read Error ERROR 04

http://getMANUAL.com

16

DVD-2930/2930CI

4. Test mode

(1) Entering the test mode

To enter the test mode, press the STOP and SKIP FWD buttons simultaneously while in the heat run mode.

Basically, enter the test mode while in the stop mode after the disc is loaded.

(The heat run mode is entered by pressing the OPEN/CLOSE and PLAY buttons simultaneously to turn on the AC power.

When the heat run mode is set, the PLAY and PAUSE indicators light.)

Press OPEN/CLOSE + PLAY buttons simultaneously

Power turns on

Press STOP + SKIP FWD buttons simultaneously PLAY button

Test mode Aging mode

FL tube display when test mode entered

(2) Selecting the mode

The following modes are available.

(1) FL tube lighting mode : T0

(2) Tray open/close mode : T1

(3) Laser on/off (CD/DVD) mode : T2

(4) Servo adjustment value display mode : T3

(5) Servo properties measurement mode : TA

(6) Trace mode (error rate display) : T7

(7) Accumulated laser on time : TB

(8) Color bar output mode : TC

(9) Monitor terminal setting mode : TD

(10) SACD watermark signal quality checking mode : TE

(11) Digital video circuitry flash ROM writing mode : TF

When the SKIP FWD button is pressed after entering the test mode, the display switches in the order: T0, T1, T2, T3, T7, TA,

TB, TC, TD, TE, TF, T0

17

DVD-2930/2930CI

When the SKIP REV button is pressed, the display switches in the opposite order from above, starting from the current position

(for example, if currently at TA, it switches as follows: T7, T3, T2, T1, T0, TF, TE, TD, TC, TB ).

18

DVD-2930/2930CI

(3) Setting the mode

With the mode selected, press the PLAY button to set that mode.

In the FL tube lighting mode, the FL tube display turns all on and all off. (When "T0" is displayed, the display switches between

all on, all off and "T0" repeatedly each time the PLAY button is pressed.)

( : Off)

In the tray open/close mode, tray opening and closing is executed and the number of times the tray has opened and closed is

displayed.

( : Off, n : No. times [DEC])

In the laser on/off (CD/DVD) mode, laser on/off control is executed. Press the SKIP REV or SKIP FWD button to display the laser

current (T21, T22, T21..).

For the CD laser

( : Off, CD laser, Stored data: mm.mm [mA], Current value: nn.nn [mA])

For the DVD laser

( : Off, DVD laser, Stored data: mm.mm [mA], Current value: nn.nn [mA])

In the servo adjustment value display mode

(XXX : Selection mode, n : Adjustment value (HEX))

In the servo properties measurement mode

(Y : 1:Focus, 2:Tracking)

In the trace mode (error rate display), select the trace of the innermost circumference of 1 layer.

(F : When address and error rate not set, F is displayed.)

19

DVD-2930/2930CI

Displaying the accumulated laser on time (stored in the EEPROM)

(Y : 1:CD, 2:DVD, nnnn.n: Time [h])

Setting the color bar output (using the video encoder function)

(Y : 1: Test pattern off : OFF

2: Test pattern off : ON

3: Reserved (same as Y = 1)

Setting the test monitor terminal setting

(Y : 1: RF signal monitor setting

2: Digital signal monitor setting (MONI 0 and 1)

3: Digital signal monitor setting (MONI 2 and 3)

4: Digital signal monitor setting (MONI 4 and 5)

5: Digital signal monitor setting (MONI 6 and 7)

6: Remaining buffer capacity output setting,

ZZ : When Y = 1: 01 to 06, 09, 0A

When Y = 2: 06 to 08, 0A, 0B, 0C

When Y = 3: 06 to 08, 0A, 0B, 0C

When Y = 4: 07 to 0F

When Y = 5: 07 to 0F)

Checking the SACD watermark signal quality

(Y : 1: PSP amplitude (Addr = 51h readout)

Hexadecimal, displayed as 2-byte data.

2: Monitor setting (Addr = 38h, Data = 06h setting)

MNIT2 terminal : Sector Detect Error

MNIT1 terminal : PDM Detect

MNIT0 terminal : PSP-DATA OK)

Setting the digital video flash ROM writing mode (switching to the 232C_UART line)

(Y : 1: Enable digital video flash ROM writing (232C_SEL : H)

2: Disable digital video flash ROM writing (232C_SEL : L)

20

DVD-2930/2930CI

(4) Change within the mode

Changes within modes are made by pressing the SKIP REV and SKIP FWD buttons while the mode is set.

In the laser on/off mode

(X : Selection mode [1, 2, 4], Y : CD or DVD, Stored data: mm.mm [mA])

In the laser on/off (CD/DVD) mode, laser on/off control is executed and the laser current is displayed.

For the CD laser

( : Off, CD laser, Stored data: mm.mm [mA], Current value: nn.nn [mA])

For the DVD laser

( : Off, DVD laser, mm.mm [mA], nn.nn [mA])

Laser off

The laser turns off when the laser on/off mode is quit.

In the servo adjustment value display mode (See Table 1 - Servo adjustment value display mode details.)

(XXX : Selection mode, n: Adjustment value (HEX))

In the servo properties measurement mode

(Y : 1: Focus properties, 2: Tracking properties)

Monitor terminal settings:

MONI7 : DIROK

MONI6 : DIRCT

MONI5 : STKC

MONI4 : TKC

MONI3 to 0 : BSDA

In the trace mode (error rate display) (See "Table 3 - Trace mode details")

(YY : Selection mode [71 to 94], F: When address and error rate not set, F is displayed.)

2

ページが読み込まれています...

Denon DVD-2930 ユーザーマニュアル

このマニュアルも適しています

Denon DVD-2930 ユーザーマニュアル

関連論文

その他のドキュメント