03903312 3PD
1.
2.
3.
4.
1.
1.
©
03903312 3PD
201a
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT
NOTES.” These sections provide important information concerning the proper operation of the unit.
Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your
new unit, owner’s manual should be read in its entirety. The manual should be saved and kept on hand as a
convenient reference.
Part Check
Before you begin attaching the floppy disk drive,
check that all the parts were supplied. You will
also need to have a Phillips screwdriver.
921
* To prevent malfunction and/or damage to speakers or
other devices, always turn down the volume, and turn off
the power on all devices before making any connections.
1.
Place the floppy disk drive and the cushion on
the holder.
2.
Using the screws, attach the holder to the piano.
3.
Attach the cord hook, then arrange the cable as
shown in the figure.
4.
Connect the cable to the piano’s FDD connector.
Owner’s Manual
Attaching the Floppy Disk
Drive
Holder
Cushion
Screw x 4
Cord Hook
Floppy Disk Drive
Inserting a floppy disk
1.
With the front of the floppy disk facing up, insert
the disk in the disk drive slot until there is an
audible click.
Removing a floppy disk
1.
Press the Eject button.
The end of the floppy disk comes out of the
slot. Grasp the edge of the floppy disk and
gently pull it out.
• Media 3.5 inch floppy disk
• Format 1.44Mbyte (2HD)
• Power Consumption
Max: 2.63 W, Average:1.1 W
• Weights 255 g / 9 oz
(includes holder and cushion: 435 g / 1 lb)
962a
* In the interest of product improvement, the specifications
and/or appearance of this unit are subject to change
without prior notice.
202
Copyright
©
2005 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced
in any form without the written permission of ROLAND CORPORATION.
Inserting and Ejecting a
Floppy Disk
Indicator
Eject Button
Floppy Disk
Specifications
This product complies with the requirements of European Directive 89/336/EEC.
For EU Countries
For Canada
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
NOTICE
AVIS
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For the USA
DECLARATION OF CONFORMITY
Compliance Information Statement
Model Name :
Type of Equipment :
Responsible Party :
Address :
Telephone :
FD-01A
Floppy Disk Drive
Roland Corporation U.S.
5100 S.Eastern Avenue, Los Angeles, CA 90040-2938
(323) 890-3700
001
• Before using this unit,
make sure to read the
instructions below, and
the Owner’s Manual.
...............................................................
002a
• Do not open or perform
any internal modifica-
tions on the unit.
...............................................................
003
• Do not attempt to repair
the unit, or replace parts
within it (except when
this manual provides specific
instructions directing you to do
so). Refer all servicing to your
retailer, the nearest Roland Service
Center, or an authorized Roland
distributor, as listed on the “Infor-
mation” page.
...............................................................
011
• Do not allow any objects
(e.g., flammable material,
coins, pins); or liquids of
any kind (water, soft
drinks, etc.) to penetrate
the unit.
...............................................................
013
• In households with small
children, an adult should
provide supervision until
the child is capable of following all
the rules essential for the safe
operation of the unit.
...............................................................
004
• Never use or store the
unit in places that are:
• Subject to temperature
extremes (e.g., direct
sunlight in an enclosed
vehicle, near a heating
duct, on top of heat-generating
equipment); or are
• Damp (e.g., baths, washrooms,
on wet floors); or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of
vibration.
................................................................
012d
• Immediately turn the
power off, and request
servicing by your retailer,
the nearest Roland Service Center,
or an authorized Roland
distributor, as listed on the “Infor-
mation” page when:
• If smoke or unusual odor occurs
• Objects have fallen into, or
liquid has been spilled onto the
unit; or
• The unit has been exposed to
rain (or otherwise has become
wet); or
• The unit does not appear to
operate normally or exhibits a
marked change in performance.
................................................................
014
• Protect the unit from
strong impact.
(Do not drop it!)
................................................................
104
• Try to prevent cords and
cables from becoming
entangled. Also, all cords
and cables should be placed so
they are out of the reach of
children.
................................................................
106
• Never climb on top of, nor
place heavy objects on the
unit.
................................................................
108c
• Disconnect all cords
coming from external
devices before moving the
unit.
................................................................
118b
• Keep the included screws
and cord hook in a safe
place out of children’s
reach, so there is no chance of
them being swallowed acciden-
tally.
................................................................
IMPORTANT NOTES
307
• Before connecting this unit to
other devices, turn off the power
to all units. This will help prevent
malfunctions and/or damage to
speakers or other devices.
352a
• This device may interfere with
radio and television reception. Do
not use this device in the vicinity
of such receivers.
354a
• Do not expose the unit to direct
sunlight, place it near devices that
radiate heat, leave it inside an
enclosed vehicle, or otherwise
subject it to temperature extremes.
Excessive heat can deform or
discolor the unit.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic
animals or pets.
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the power-
cord plug must be unplugged from the outlet.
The symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
353
• Observe the following when using the unit’s floppy
disk drive. For further details, refer to “Before Using
Floppy Disks.”
• Do not place the unit near devices that produce a
strong magnetic field (e.g., loudspeakers).
• Install the unit on a solid, level surface.
• Do not move the unit or subject it to vibration while
the drive is operating.
355b
• When moved from one location to another where the
temperature and/or humidity is very different, water
droplets (condensation) may form inside the unit.
Damage or malfunction may result if you attempt to
use the unit in this condition. Therefore, before using
the unit, you must allow it to stand for several hours,
until the condensation has completely evaporated.
401a
• For everyday cleaning wipe the unit with a soft, dry
cloth or one that has been slightly dampened with
water. To remove stubborn dirt, use a cloth impreg-
nated with a mild, non-abrasive detergent. After-
wards, be sure to wipe the unit thoroughly with a
soft, dry cloth.
402
• Never use benzine, thinners, alcohol or solvents of
any kind, to avoid the possibility of discoloration
and/or deformation.
552
• Unfortunately, it may be impossible to restore the
contents of data that was stored on a floppy disk once
it has been lost. Roland Corporation assumes no
liability concerning such loss of data.
553
• Use a reasonable amount of care when using the
unit’s buttons, sliders, or other controls; and when
using its jacks and connectors. Rough handling can
lead to malfunctions.
556
• When connecting / disconnecting all cables, grasp the
connector itself—never pull on the cable. This way
you will avoid causing shorts, or damage to the
cable’s internal elements.
559a
• When you need to transport the unit, package it in the
box (including padding) that it came in, if possible.
Otherwise, you will need to use equivalent packaging
materials.
Handling the Floppy Disk Drive
603
• Avoid using the unit immediately after it has been
moved to a location with a level of humidity that is
greatly different than its former location. Rapid
changes in the environment can cause condensation
to form inside the drive, which will adversely affect
the operation of the drive and/or damage floppy
disks. When the unit has been moved, allow it to
become accustomed to the new environment (allow a
few hours) before operating it.
604
• To insert a disk, push it gently but firmly into the
drive—it will click into place. To remove a disk, press
the EJECT button firmly. Do not use excessive force to
remove a disk which is lodged in the drive.
605a
• Never attempt to remove a floppy disk from the drive
while the drive is operating (the indicator is lit);
damage could result to both the disk and the drive.
606
• Remove any disk from the drive before powering up
or down.
607
• To prevent damage to the disk drive’s heads, always
try to hold the floppy disk in a level position (not
tilted in any direction) while inserting it into the
drive. Push it in firmly, but gently. Never use
excessive force.
608
• To avoid the risk of malfunction and/or damage,
insert only floppy disks into the disk drive. Never
insert any other type of disk. Avoid getting paper
clips, coins, or any other foreign objects inside the
drive.
651
• Floppy disks contain a plastic disk with a thin coating
of magnetic storage medium. Microscopic precision is
required to enable storage of large amounts of data on
such a small surface area. To preserve their integrity,
please observe the following when handling floppy
disks:
• Never touch the magnetic medium inside the disk.
• Do not use or store floppy disks in dirty or dusty
areas.
• Do not subject floppy disks to temperature extremes
(e.g., direct sunlight in an enclosed vehicle). Recom-
mended temperature range: 10 to 50˚C (50 to 122˚F).
• Do not expose floppy disks to strong magnetic
fields, such as those generated by loudspeakers.
652
• Floppy disks have a “write protect” tab which can
protect the disk from accidental erasure. It is recom-
mended that the tab be kept in the PROTECT
position, and moved to the WRITE position only
when you wish to write new data onto the disk.
653
• The identification label should be firmly affixed to the
disk. Should the label come loose while the disk is in
the drive, it may be difficult to remove the disk.
654
• Store all disks in a safe place to avoid damaging them,
and to protect them from dust, dirt, and other
hazards. By using a dirty or dust-ridden disk, you
risk damaging the disk, as well as causing the disk
drive to malfunction.
655
• Disks containing performance data for this unit
should always be locked (have their write protect tab
slid to the “Protect” position) before you insert them
into the drive on some other unit (except the PR-300,
or a product in the HP-G, MT, KR, or Atelier families),
or into a computer’s drive. Otherwise (if the write
protect tab remains in the “Write” position), when
you perform any disk operations using the other
device’s disk drive (such as checking the contents of
the disk, or loading data), you risk rendering the disk
unreadable by this unit’s disk drive.
Rear side of the disk
Write
(can write new data
onto disk)
Protect
(prevents writing
to disk)
Write Protect Tab
-
1
-
2
