MG-12000P
2018.04
V1.0
User Guide
使用说明
사용자 가이드
Flight Battery
2
Battery Functions
The functions of the MG-12000P are as follows:
1. Battery Level Display: The current battery level can be indicated by the LEDs.
2. Communication: Battery parameters including voltage and charge are transmitted to the aircraft
to enable the aircraft to take appropriate action when battery parameters change.
3. Battery Management: When the battery is connected to the aircraft the management system is
active. The battery enters into power saving mode when it is disconnected from the aircraft.
4. Battery Exception Record: Battery exceptions such as excessive charging/discharging, the
temperature being outside the ranges allowed for charging/discharging, and the battery being
Read Before the First Use
The following terms are used in this document and the product warning label to indicate various
levels of potential harm when operating this product:
WARNING: Procedures which, if not properly followed, create the probability of property
damage, collateral damage, and serious injury OR a high probability of supercial injury.
CAUTION: Procedures which, if not properly followed, create a possibility of physical property
damage AND a small possibility of injury.
This product is specialist and must be operated with caution and expertise. It requires some basic
mechanical ability. Failure to operate this product in a safe and responsible manner could result
in injury or damage to the product or other property. This product is not intended for use by those
who are under 16 years old. DO NOT use this product with incompatible components, or alter
this product in any way outside of the documents provided by the manufacturer. This document
contains instructions for safety, operation and maintenance. It is essential to read and follow all of
the instructions and warnings herein, prior to assembly, setup or use, in order to operate the product
correctly and avoid damage or serious injury.
Introduction
The MG-12000P Flight Battery (hereafter referred to as “the battery”) has a capacity of 12,000 mAh
at a voltage of 44.4 V. The battery features a charging and discharging monitoring function, and its
advanced power management system and high energy battery cells mean it can provide the power
that your aircraft requires.
LED4
LED3
LED2
LED1
Charging and
Balancing Port
Charging and
Balancing Port
Cover
Power
Port
Power Port
Rubber Cover
Battery Level Indicator Button
3
stored long-term with the charge level outside the recommended range are recorded and can
be accessed by authorized dealer engineers when troubleshooting or repairing.
5. Charging Exceptions: Exceptions that occur during charging are indicated by the LEDs. Refer to
the LED Patterns section for more details.
6. Auto Balancing: When the battery is in power saving mode for certain length of time, it
automatically balances its cell voltages.
7. Auto Discharging: If the battery remains fully charged for more than 10 days it automatically
discharges to 65% charge.
8. Removable Ports: If the Power Port or Charging and Balancing Port are found to be burned,
corroded, or otherwise damaged they can be replaced by an authorized dealer.
• Refer to the safety requirements on the label afxed to the battery before using the battery.
Users accept full responsibility for any violations of the safety requirements stated on the
label.
• The product warranty expires 6 months after the battery is delivered or after 180 charging/
discharging cycles, whichever is sooner. The product warranty is void if any battery
exceptions occur due to misuse of the battery. (The current number of charging/discharging
cycles can be checked in the mobile device app used when ying the aircraft.)
Using the Battery
Check if the battery rmware version is compatible with the aircraft before using the battery. (Refer
to the aircraft documentation for information about how to check the rmware version compatibility).
If the firmware update fails be sure to retry. Only use the battery once it has been successfully
updated. Refer to the LED Patterns section to see the warning of battery update failure.
Turning the Battery on/off
The battery turns on/off automatically when connected to / disconnected from the aircraft.
• DO NOT allow the battery to come into contact with any kind of liquid. DO NOT leave the
battery near a source of moisture and do not use the battery in humid environments. If
the inside of the battery comes into contact with liquid corrosion may occur, potentially
resulting in the battery catching re, and possibly leading to an explosion.
• Electrolytes in the battery are highly corrosive. If any electrolytes come into contact with
your skin or eyes, immediately wash the affected area with fresh running water for at least
15 minutes, and then see a doctor immediately.
• If the battery falls into water with the aircraft during ight, take it out immediately and put it
in a safe and open area. Never use it again, and dispose of it properly as described in the
Battery Disposal section below.
• Put out any battery re using sand or a dry powder re extinguisher.
• Always use a clean, dry cloth when cleaning the battery terminals otherwise connection
failure may occur.
• DO NOT place the battery on or near wires or other metal objects such as spectacles,
watches, jewelry, and hairpins which could lead to the battery ports becoming short-
circuited.
• Only use officially recommended batteries. Only purchase batteries from authorized
dealers. The manufacturer takes no responsibility for any damaged caused by non-ofcially
recommended batteries.
4
• Never use or charge swollen, leaky, or damaged batteries. If your battery is abnormal,
contact an authorized dealer for further assistance.
• The battery should normally be used in the temperature range 41° to 113° F (5° to 45° C).
Use of the battery in environments above 122° F (50° C) can lead to re or explosion. Use
of the battery in temperatures below 32° F (0° C) can lead to a sharp decrease in ight
time. (If using the battery in the temperature range 23° F to 41° F (-5° to 5° C) it must rst
be ensured that the battery voltage is at its maximum. In this temperature range the aircraft
should be own with no load.)
• DO NOT use the battery in strong electrostatic or electromagnetic environments or near
high-voltage transmission lines otherwise the battery control board may malfunction and
cause a serious accident during ight.
• Never disassemble or pierce the battery in any way or it may leak, catch re, or explode.
• Batteries that fall off are very dangerous. DO NOT use such batteries and dispose of them
as described in the Battery Disposal section.
• DO NOT put the battery in a microwave oven or in a pressurized container.
• DO NOT drop, strike, impale, or manually short-circuit the battery.
• DO NOT place heavy objects on the battery.
• Always hold the bar instead of the cables or the rubber belt when lifting the battery.
• Ensure the battery is fully charged before each ight.
• Immediately land the aircraft if a critical battery level warning appears and replace the
battery with a fully charged one.
• When operating in low temperature environments, before using the battery rst leave it in
a room temperature environment and allow it to gently warm to above 41° F (5° C) (ideally
above 68 ° F (20° C)).
• Cover the ports with the rubber covers when the battery is not in use to protect the ports
from moisture and dirt, which could lead to corrosion or other issues.
LED Patterns
Battery Level LED Patterns
LED is on LED is ashing
LED is off
If the battery is in power saving mode press the Battery Level Indicator button once to check
current battery level. (Note: If a battery exception has occurred, when the Battery Level Indicator
is pressed the LEDs indicate which exception has occurred. Refer to the Battery Exception LED
Patterns section for further information.)
LED1 LED2 LED3 LED4 Battery Level
88%~100%
75%~87%
63%~74%
50%~62%
38%~49%
5
25%~37%
13%~24%
0%~12%
LED Patterns During Charging
During charging the LEDs indicate the current battery level. (Note: During charging, if a battery
exception has occurred the LEDs indicate which exception has occurred. Refer to the Battery
Exception LED Pattens section for further information.) Disconnect the battery when charging is
complete.
LED1 LED2 LED3 LED4 Battery Level
0%~49%
50%~74%
75%~99%
100%
Battery Exception LED Patterns
If a battery exception occurs during charging the LEDs indicate which exception has occurred.
(Note: During charging, if no battery exception has occurred the LEDs indicate the current battery
level. Refer to the Battery Level LED Patterns section for further information.)
To check for battery exceptions while the battery is not being charged press the Battery Level
Indicator button once. (Note: If no battery exception has occurred, when the Battery Level Indicator
is pressed the LEDs indicate the current battery level. Refer to the Battery Level LED Patterns
section for further information.)
Battery exceptions may also be lead to a warning being displayed in the mobile device app used
when ying the aircraft.
The battery can self-recover from some battery exceptions. If one of the following battery exceptions
occurs, let the battery rest for a while to attempt self-recovery:
LED1 LED2 LED3 LED4 Pattern Battery Exception Item
LED2 blinks twice per second Overcurrent detected
LED3 blinks twice per second Overcharge detected
LED3 blinks three times per
second
Battery charger over-voltage
LED4 blinks twice per second
Charging temperature is too
low
LED4 blinks three times per
second
Charging temperature is too
high
LED1 and LED4 blinks
Difference between cell
voltages is too large
LED2 and LED3 blinks Battery rmware update failure
6
• Keep batteries out of the reach of children and pets. Seek professional medical advice
immediately if a child swallows any battery part.
• DO NOT leave the battery near heat sources such as a furnace or heater. DO NOT leave
the batteries inside a vehicle on hot days. It is strongly recommended that the battery is
never stored in environments outside the temperature range of -4° to 104° F (-20° C to
40° C). Never store the battery in environments (such as vehicles on hot days) where the
temperature may exceed 122° F (50° C).
• DO NOT drop, strike, impale, or manually short-circuit the battery.
11
1
2
• Only use an approved charger for charging. The manufacturer takes no responsibility if the
battery is charged using an unapproved charger.
• DO NOT charge the battery near ammable materials or on ammable surfaces such as
carpet or wood. Never leave the battery unattended during charging.
• Never try to charge a damaged battery. Never use a damaged charger.
• Disconnect the battery and the charger when not charging.
• DO NOT charge the battery immediately after ight. The battery temperature may be too
high and may cause serious damage to the battery. Allow the battery to cool down to close
to room temperature before charging. Charge the battery at a temperature range of 41° to
104° F (5° to 40° C). The ideal charging temperature range is 68° to 82 ° F (20° to 28° C).
Charging at the ideal temperature range can prolong battery life.
• DO NOT allow the battery to come into contact with any kind of liquid. Charging a wet
battery could be very dangerous.
• When the LEDs indicate that a battery exception has occurred stop charging immediately
and review the exception. DO NOT use the battery until the exception has been resolved.
• When the battery is not being charged, unplug the Charging and Balancing Cable (if used)
to avoid a short-circuit occurring and cover the Charging and Balancing port with the
rubber cover to protect the port from moisture and dirt, which could lead to corrosion or
other issues.
Battery Storage
Use the rubber belt to securely tie the battery power cable for storage as shown in the figures
below. Ensure that the rubber covers are not damaged and are clear of contaminants such as
liquids and residues, then use the covers to carefully cover all the ports to avoid extended terminal
exposure.
7
• DO NOT place the battery on or near wires or other metal objects such as spectacles,
watches, jewelry, and hairpins which could lead to the battery ports becoming short-
circuited.
• Never attempt to travel with or transport a damaged battery or a battery with a charge level
higher than 30%.
• Charge the battery until the battery level reaches between 30 % and 50 % for storage if the
power level is less than 10% after ight.
• It is recommended that the battery is stored in a battery safe bag when storing for more
than 3 months.
• Even when the power cable is secured using the rubber belt it should not be used for
lifting the battery. Always hold the bar instead of the cables or the rubber belt when lifting
the battery.
Battery Disposal
Dispose of the battery in specic recycling boxes in your local area and only after a complete
discharge. DO NOT place the battery in regular trash containers. Strictly follow your local
regulations regarding the disposal and recycling of batteries.
Battery Care and Maintenance
• Never use or store the battery or the charger when the temperature is outside the
recommended ranges.
• Never store the battery in vehicles in summer where the temperature is far above 114 ° F (50° C).
• Never over-charge or discharge, as this may lead to battery cell damage.
• Battery life may be reduced if not used for a long time. Fully charge and discharge the
battery at least once every three months to maintain battery health.
• Regularly clean the rubber covers and change the rubber covers if there is any liquid or
residue on them. If the Power Port or Charging and Balancing Port are found to be burned,
corroded, or otherwise damaged contact an authorized dealer to arrange replacement.
8
Specications
Model MG-12000P MAH-44.4V
Capacity 12000 mAh
Compatible Aircraft Models
DJI MG-1*, DJI MG-1S*, DJI MG-1S Advanced
DJI MG-1P, DJI MG-1P RTK
Compatible Battery Chargers
MG Smart Battery Charger**, MG 6-Channel
Intelligent Battery Charger
Voltage 44.4 V
Battery Type LiPo 12S
Energy 532 Wh
Maximum Battery Cycle Count 300
Net Weight 4.0 kg
Operating Temperature Range 23° to 104° F (-5° to 40° C)
Max Charging Power 1200 W
Charging Time
Fast Charge: Approx. 25 to 30 minutes.
Slow Charge: Approx. 50 minutes.
* A power cable adapter is required when the battery is used with DJI MG-1 or DJI MG-1S aircraft.
** A charging and balancing cable and a power cable adapter are required if charging the battery
using an MG Smart Battery Charger.
9
电池功能
MG-12000P 电池具有以下功能：
1. 电量显示：电池自带指示灯，可以显示当前电池电量。
2. 智能通讯：通过电池上的电源接口可实时获得电池信息，例如电压、电量等信息，确保飞行
器能正常工作。
3. 智能管理：电池连接至设备后，管理系统自动识别并提供指示灯显示。断开连接后，电池将
进入低功耗状态。
4. 异常使用记录：管理系统可显示异常记录，如高低温充放电、充电过流、放电过流、长时间
高电量储存。
5. 充电异常提示：在充电过程中出现异常，可根据指示灯提示将电池静置，待电池进行自我修复，
详见异常指示表。
6. 自动均衡功能：当电池休眠静置达到一定条件后，电池将自动开启均衡功能，以均衡电压。
7. 自动放电功能：电池具有自放电功能，当电池满电超过 10 天，电池将会自动放电至 65% 左
右进行存储。
阅读提示
本产品使用以下词条对因操作不当可能带来的潜在危险加以分级说明。
警告 : 如果不遵循说明进行操作，可能会导致财产损失、重大事故和严重伤害。
注意 : 如果不遵循说明进行操作，可能会导致财产损失和轻微伤害。
本产品较为复杂，需要经过一段时间熟悉后才能安全使用，并且需要具备一些专业知识后才能
进行操作。如果没有强烈的安全意识，不恰当的操作可能会导致产品损坏和财产损失，甚至对
自身或他人造成严重伤害。本产品严禁十六周岁以下人士使用。切勿使用非官方提供或建议的
部件，必须严格遵守官方的指引安装和使用产品。本说明文档包含安全、操作和维护等说明。
在进行组装、设置和使用之前务必仔细阅读本说明中的所有说明和警告。
简 介
MG-12000P 飞行电池（以下简称电池）是一款容量为 12000mAh、电压为 44.4V，带有充放
电检测功能的电池。该款电池采用了全新的高能电芯和先进的电池管理系统为飞行器提供充沛
电力。
LED4
LED3
LED2
LED1
充电平衡接口
充电平衡
接口保护盖
电源接口
电源接口保护盖
电量显示开关
10
8. 接口更换：使用过程中，若电源接口出现烧黑的现象，或充电平衡接口有污渍及损坏，可联
系当地经销商更换后继续使用。
使用电池前请详细阅读并严格遵守电池表面贴纸上的要求。未按要求使用造成的后果由
用户承担。
对于非正常使用导致产生电池异常记录，或使用期限超过六个月，或充放电次数超过
180 次的电池将不予保修（用户可于 App 中查看电池循环次数）。
使用电池
使用电池前，请检查电池固件版本是否与飞行器匹配（请查阅飞行器用户手册了解固件升级方
法），若升级固件时提示失败，请务必再次升级，升级成功后再使用电池。关于电池升级失败
的提示，请查看异常指示表。
开启 / 关闭飞行电池
开启飞行电池：连接电池电源接口至飞行器以开启电池。
关闭飞行电池：断开电池电源接口。
严禁将电池接触或浸入任何液体。潮湿环境中切勿使用电池，否则电池内部接触到外部
液体后可能会发生腐蚀，引发电池自燃，甚至可能引发爆炸。
电池内部液体有强腐蚀性，如有泄露，请远离。如果内部液体溅射到人体皮肤或者眼睛，
请立即用清水冲洗至少 15 分钟，并立即就医。
如果电池在飞行器飞行过程中或其他情况下意外坠入水中，请取下电池并将其置于开阔
安全的区域，并远离电池将电池完全晾干。晾干的电池不建议再次使用，并按照本文的
废弃方法妥善处理。若电池发生起火，请使用干粉、二氧化碳灭火器等固体灭火器材。
如果电池接口有污物，使用干布擦干净。否则会造成接触不良，从而引起能量损耗及严
重发热。
禁止用导线或其它金属物体（如眼镜、手表、金属项链、发夹等）致使电池正负极或充
电平衡接口短路。
严禁使用非官方推荐的电池。如需更换，请联系售后或是指定代理商。因使用非官方提
供的电池而引发的电池事故、飞行故障，概不负责。
严禁使用鼓包的、漏液的、外壳破损的电池。如有以上情况发生，请联系售后或者指定
代理商做进一步处理。
电池应在温度为 5℃ ~ 45℃之间使用。温度过高（高于 50℃），会引起电池着火，甚
至爆炸。在低温环境（0℃以下），电池容量将骤减从而导致飞行时间急剧减少。( 当
电池温度为 -5℃ ~ 5℃时，如需飞行，需满足满电压才可起飞，且飞行器为空载，以
免造成损失。)
禁止在强静电，磁场环境或高压线环境中使用电池。否则可能导致电池保护板异常，从
而导致飞行器发生严重故障。
禁止以任何方式拆解或用尖利物体刺破电池。否则，将会引起电池着火甚至爆炸。
摔落的电池非常危险，切勿再次使用。请放入电池专用箱后进行报废处理。
请勿将电池放置于微波炉或压力锅中。
11
禁止撞击、碾压、刺穿电池，禁止将电池跌落或人为短路。
请勿在电池或充电器上放置重物。
拿取电池时，请务必握住电池提手，切勿提拉橡胶带或电源线。
每次飞行之前，确保电池充满电。
若飞行器进入低电量报警模式，应尽快降落并停止飞行，更换电池。
在低温环境下，建议在飞行前将电池预热至 5℃以上，预热至 20℃更佳。
当不使用电池时，请盖好电源接口保护盖，以免插头受潮及腐蚀。
LED 显示状态
电量指示灯可用于显示电池充放电过程中的电量以及状态，指示灯定义如下：
表示 LED 灯在指示过程中常亮 表示 LED 灯在指示过程中有规律地闪亮
表示 LED 灯熄灭
查看电量
在电池休眠状态下，短按电量显示开关一次，可查看当前电量。
LED1 LED2 LED3 LED4 当前电量
88% - 100%
75%~87%
63%~74%
50%~62%
38%~49%
25%~37%
13%~24%
0%~12%
充电状态
电池在充电时，LED 灯将逐渐闪烁提示充电状态。充电完毕后请断开和充电器的连接。
LED1 LED2 LED3 LED4 当前电池电量
0%~49%
50%~74%
75%~99%
100%
12
异常指示表
充电时，若电池发生异常，LED 灯将会显示由于充电异常而触发电池保护的相关信息。充电时，
若无异常，则电池 LED 灯将会显示当前电池电量，请查看充电状态章节。
当电池不充电时，可短按一次电量显示开关，若电池发生异常，则 LED 灯将会显示由于充电异
常而触发电池保护的相关信息。若电池正常，LED 灯则显示当前电池电量，请查看查看电量章节。
当电池出现异常时，飞行器 App 中将出现提示。电池异常时，请根据指示灯提示将电池静置，
待电池进行自我修复。
LED1 LED2 LED3 LED4 显示规则 保护项目
LED2 每秒闪 2 次 充电电流过大
LED3 每秒闪 2 次 充电过充导致电池电压过高
LED3 每秒闪 3 次 充电器电压过高
LED4 每秒闪 2 次 充电温度过低
LED4 每秒闪 3 次 充电温度过高
LED1、LED4 闪烁 电芯压差过大
LED2、LED3 快闪 电池升级失败
电池必须使用官方提供的专用充电器进行充电。对于使用非官方提供的充电器进行充电
所造成的一切后果，将不予负责。
充电时请将电池和充电器放置在水泥地面等周围无易燃、可燃物的地面。请留意充电过
程，以防发生意外。请勿在无人值守时充电。
充电完毕后请断开充电器与电池间的连接。
经常检查电池接口、插头等各个部件。切勿使用酒精或者其它可燃剂清洁电池。切勿使
用已有损坏的电池。
禁止在飞行器飞行结束后立刻对电池进行充电。此时，电池处于高温状态，强制充电会
对电池寿命造成严重损害。建议待电池降至室温，再进行充电。电池可于 5℃ ~40℃的
环境下进行充电。理想的充电环境温度（20℃ ~28℃）可延长电池的使用寿命。
确保电池在干燥状态下进行充电。
当充电器上异常指示灯闪烁时，需立即停止充电并检查异常情况，直至异常情况消除
后方可继续充电。
当电池不处于充电状态时，请拔出充电平衡连接线（若使用），以免造成短路。盖好
充电平衡接口保护盖，以免杂质、液体等进入平衡接口，腐蚀插头。
电池存储
如不使用电池，请按照如图所示将电池进行捆绑收纳，并将所有接口保护盖盖上，避免金属端
子暴露在外。盖上接口保护盖前，务必确认保护盖中无水等杂物。若保护盖有破损，请立即更换。
13
请将电池存放在儿童接触不到的地方。如果儿童不小心吞咽零部件，应立即寻求医疗
救助。
禁止将电池放在靠近热源的地方，比如阳光直射或热天的车内、火源或加热炉。电池
必须存储在 -20~40℃的范围内。
禁止机械撞击、碾压、刺穿电池，禁止将电池跌落或人为短路。
禁止将电池与眼镜、手表、金属项链、发夹或者其他金属物体一起贮存或运输。
切勿长途运输有破损或电池电量高于 30% 的电池。
飞行后若电池电量低于 10%，请将电池充电至 30% 至 50% 进行存放，否则可能导致电
池损坏。
若长期（超过 3 个月）存储电池，则必须置于温度为 -20~40℃的环境中，并建议使用
电池专用安全袋进行存储。
拿取电池时，请务必握住电池提手，切勿提拉橡胶带或电源线。
废 弃
务必将电池彻底放完电后，才可将电池置于指定的电池回收箱中。电池是危险化学品，严
禁废置于普通垃圾箱。相关细节，请遵循当地电池回收和弃置的法律法规。
保 养
切勿在温度过高或温度过低的环境下使用电池和充电器。
切勿将电池存储在室温超过 50℃的环境下（如：夏季汽车内）。
切勿过充或过放电池，否则将对电芯造成损害。
若长期闲置电池，将会对其性能造成影响。
每隔 3 个月左右重新充放电一次以保持电池活性。
请定期清洁保护盖，若有农药残留请更换保护盖。若发现电源及充电平衡接口有烧黑及
腐蚀现象，请联系经销商更换相应部件。
11
1
2
14
技术参数
型号 MG-12000P MAH-44.4V）
容量 12000 mAh
适配飞行器型号
DJI MG-1*，DJI MG-1S*，MG-1S Advanced
DJI MG-1P，DJI MG-1P RTK
适配充电器型号 MG 智能平衡充电器 **，MG 六通道智能充电器
电压 44.4 V
电池类型 LiPo 12S
能量 532 Wh
电池最大循环次数 300
电池整体重量 4.0 kg
工作环境温度 -5 至 40℃
最大充电功率 1200 W
充电时间
快充：25~30 分钟
慢充：约 50 分钟
* 于 DJI MG-1 及 MG-1S 飞行器中使用该电池时需额外购买电源转接线配合使用。
** 使用 MG 智能平衡充电器为电池进行充电时，请额外购买充电平衡连接线及电源转接线。
15
MG-12000P
1. LED
2.
3.
4.
16
MG-12000P 12,000mAh 44.4V
LED4
LED3
LED2
LED1
16
5. LED LED
6.
7. 10 65%
8.
•
• 6 180
LED
•
•
15
•
•
•
•
•
•
17
• 5 45 50
0
-5 5
•
•
•
•
•
•
•
•
•
• 5
20
•
LED
LED
LED LED
LED
1
LED LED
LED1 LED2 LED3 LED4
88 100%
75 87%
63 74%
50 62%
38 49%
25 37%
13 24%
0 12%
18
LED
LED
LED LED
LED1 LED2 LED3 LED4
0 49%
50 74%
75 99%
100%
LED
LED
LED
LED
1
LED LED
LED1 LED2 LED3 LED4
LED2 2
LED3 2
LED3 3
LED4 2
LED4 3
LED1 LED4
LED2 LED3
•
•
•
•
19
•
•
-20 40
50
•
•
• 30%
• 10% 30 50%
• 3
11
1
2
•
5 40
20 28
•
• LED
•
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
他の言語で
- English: dji Assistant 2 for MG User manual
関連論文
その他のドキュメント
-
Walkera QL 1200 ユーザーマニュアル
-
ZEROZERO PA43H063 Hover Camera 取扱説明書
-
Fujitsu UTY-TFNXZ4 インストールガイド
-
-
-
-
Autel Robotics EVO Nano Series ユーザーガイド
-
Promaster FBP4500 取扱説明書
-
Promaster FBP4500 Flash Power System 取扱説明書
-
Lenovo LBC-007 クイックスタートガイド
