SICK PowerProx Micro - WTT2SL(C) 取扱説明書

O P E R A T I N G I N S T R U C T I O N S

PowerProx Micro - WTT2SL(C)

Miniature MultiTask photoelectric sensor

O P E R A T I N G I N S T R U C T I O N S

PowerProx Micro - WTT2SL(C)

Miniature MultiTask photoelectric sensor

de

en

es

fr

it

ja

pt

ru

zh

Described product

WTT2SL(C)

Manufacturer

SICK AG

Erwin-Sick-Str. 1

79183 Waldkirch

Germany

Legal information

This work is protected by copyright. Any rights derived from the copyright shall be

reserved for SICK AG. Reproduction of this document or parts of this document is only

permissible within the limits of the legal determination of Copyright Law. Any modifica‐

tion, abridgment or translation of this document is prohibited without the express writ‐

ten permission of SICK AG.

The trademarks stated in this document are the property of their respective owner.

Original document

This document is an original document of SICK AG.

2006/42/EG

NO

SAFETY

2

8021879.ZZG2 | SICK

Subject to change without notice

Contents

1 About this document........................................................................ 5

1.1 Information on the operating instructions.............................................. 5

1.2 Scope......................................................................................................... 5

1.3 Explanation of symbols............................................................................ 5

1.4 Further information................................................................................... 6

1.5 Customer service...................................................................................... 6

2 Safety information............................................................................ 7

2.1 General safety notes................................................................................ 7

2.2 Intended use............................................................................................. 7

2.3 Improper use............................................................................................. 7

2.4 Limitation of liability................................................................................. 8

2.5 Requirements for skilled persons and operating personnel.................. 8

2.6 Hazard warnings and operational safety................................................. 9

2.7 Repairs...................................................................................................... 9

3 Product description........................................................................... 10

3.1 Device view................................................................................................ 10

4 Mounting............................................................................................. 10

4.1 Scope of delivery....................................................................................... 10

4.2 Mounting requirements............................................................................ 10

4.3 Mounting the device................................................................................. 11

5 Electrical installation........................................................................ 12

5.1 Notes on the electrical installation.......................................................... 12

5.2 Pin assignment of the connections......................................................... 13

5.3 Connecting the supply voltage................................................................. 13

6 Commissioning.................................................................................. 14

6.1 Sensing range setting............................................................................... 14

6.2 Switching behavior.................................................................................... 14

6.3 Additional functions.................................................................................. 15

7 Troubleshooting................................................................................. 15

7.1 ................................................................................................................... 15

8 Maintenance...................................................................................... 15

8.1 Maintenance............................................................................................. 15

8.2 Cleaning the device.................................................................................. 16

9 Decommissioning............................................................................. 17

9.1 Disassembly and disposal....................................................................... 17

9.2 Returning devices..................................................................................... 17

CONTENTS

8021879.ZZG2 | SICK

Subject to change without notice

3

10 Technical data.................................................................................... 17

10.1 Technical data........................................................................................... 17

10.2 Dimensional drawings.............................................................................. 19

4

8021879.ZZG2 | SICK

Subject to change without notice

1 About this document

1.1 Information on the operating instructions

These operating instructions provide important information on how to use devices from

SICK AG.

Prerequisites for safe work are:

•

Compliance with all safety notes and handling instructions supplied

•

Compliance with local work safety regulations and general safety regulations for

device applications

The operating instructions are intended to be used by qualified personnel and electrical

specialists.

NOTE

Read these operating instructions carefully before starting any work on the device, in

order to familiarize yourself with the device and its functions.

The instructions constitute an integral part of the product and are to be stored in the

immediate vicinity of the device so they remain accessible to staff at all times. Should

the device be passed on to a third party, these operating instructions should be handed

over with it.

These operating instructions do not provide information on operating the machine in

which the device is integrated. For information about this, refer to the operating instruc‐

tions of the specific machine.

1.2 Scope

These operating instructions serve to incorporate the device into a customer system.

Instructions are given in stages for all actions required.

These instructions apply to all listed device variants of the product.

Available device variants are listed on the online product page.

b

www.sick.com/PowerProx

Commissioning is described using one particular device variant as an example.

Simplified device designation in the document

In the following, the sensor is referred to in simplified form as “WTT2SL(C)” or “device”.

1.3 Explanation of symbols

Warnings and important information in this document are labeled with symbols. The

warnings are introduced by signal words that indicate the extent of the danger. These

warnings must be observed at all times and care must be taken to avoid accidents, per‐

sonal injury, and material damage.

DANGER

… indicates a situation of imminent danger, which will lead to a fatality or serious

injuries if not prevented.

ABOUT THIS DOCUMENT 1

8021879.ZZG2 | SICK

Subject to change without notice

5

WARNING

… indicates a potentially dangerous situation, which may lead to a fatality or serious

injuries if not prevented.

CAUTION

… indicates a potentially dangerous situation, which may lead to minor/slight injuries if

not prevented.

NOTICE

… indicates a potentially harmful situation, which may lead to material damage if not

prevented.

NOTE

… highlights useful tips and recommendations as well as information for efficient and

trouble-free operation.

1.4 Further information

NOTE

All the documentation available for the device can be found on the online product page

at:

b

www.sick.com/PowerProx

The following information is available for download from this page:

•

Type-specific online data sheets for device variants, containing technical data and

dimensional drawings

•

EU declaration of conformity for the product family

•

Dimensional drawings and 3D CAD dimension models in various electronic for‐

mats

•

These operating instructions, available in English and German, and in other lan‐

guages if necessary

•

Other publications related to the devices described here

•

Publications dealing with accessories

•

IO-Link driver files and IO-Link Technical Information v1.1

1.5 Customer service

If you require any technical information, our customer service department will be happy

to help. To find your agency, see the final page of this document.

NOTE

Before calling, make a note of all type label data such as type code, serial number, etc.,

to ensure faster processing.

1 ABOUT THIS DOCUMENT

6

8021879.ZZG2 | SICK

Subject to change without notice

2 Safety information

2.1 General safety notes

2.1.1 Safety notes

■

Read the operating instructions before commissioning.

■

- Connection, mounting, and setting is only to be performed by skilled per‐

son.

■

2006/42/EG

NO

SAFETY

- Not a safety component in accordance with the EU Machinery Directive.

■

- Do not install the sensor at locations that are exposed to direct sunlight or

other weather influences, unless this is expressly permitted in the operating

instructions.

■

When commissioning, protect the device from moisture and contamination

■

These operating instructions contain information required during the life cycle of

the sensor.

EN/IEC 60825-1:2014

IEC60825-1:2007

Laser

1

Maximum pulse power < 20 mW

Puls length: 5.3 µs

Wavelength: 940 nm

Complies with 21 CFR 1040.10

and 1040.11 except for deviations

pursuant to Laser Notice No. 50,

dated June 24, 2007

LASER CLASS 1

ATTENTION

WARNING: Interruption, manipulation or incorrect use can lead to hazardous exposure

due to laser radiation.

2.2 Intended use

The WTT2SL(C) is an opto-electronic photoelectric proximity sensor (referred to as “sen‐

sor” in the following) for the optical, non-contact detection of objects.

The system designer must provide measures to ensure the safety of persons and sys‐

tems in accordance with the legal guidelines.

SICK AG assumes no liability for losses or damage arising from the use of the product,

either directly or indirectly. This applies in particular to use of the product that does not

conform to its intended purpose and is not described in this documentation.

2.3 Improper use

•

The device does not constitute a safety-relevant device according to the EC

Machinery Directive (2006/42/EC).

•

The device must not be used in explosion-hazardous areas.

SAFETY INFORMATION 2

8021879.ZZG2 | SICK

Subject to change without notice

7

•

Any other use that is not described as intended use is prohibited.

•

Any use of accessories not specifically approved by SICK AG is at your own risk.

The device is not suitable for the following applications (this list is not exhaustive):

•

As a safety device to protect persons, their hands, or other body parts

•

Underwater

•

In explosion-hazardous areas

•

Outdoors, without additional protection

NOTICE

Danger due to improper use!

Any improper use can result in dangerous situations.

Therefore, observe the following information:

b

The device should be used only in line with intended use specifications.

b

All information in these operating instructions must be strictly complied with.

2.4 Limitation of liability

Applicable standards and regulations, the latest technological developments, and our

many years of knowledge and experience have all been taken into account when

assembling the data and information contained in these operating instructions. The

manufacturer accepts no liability for damage caused by:

■

Failing to observe the operating instructions

■

Improper use

■

Use by untrained personnel

■

Unauthorized conversions

■

Technical modifications

■

Use of unauthorized spare parts, consumables, and accessories

With special variants, where optional extras have been ordered, or owing to the latest

technical changes, the actual scope of delivery may vary from the features and illustra‐

tions shown here.

2.5 Requirements for skilled persons and operating personnel

WARNING

Risk of injury due to insufficient training.

Improper handling of the device may result in considerable personal injury and material

damage.

■

All work must only ever be carried out by the stipulated persons.

The operating instructions state the following qualification requirements for the various

areas of work:

2 SAFETY INFORMATION

8

8021879.ZZG2 | SICK

Subject to change without notice

■

Instructed personnel have been briefed by the operating entity about the tasks

assigned to them and about potential dangers arising from improper action.

■

Skilled personnel have the specialist training, skills, and experience, as well as

knowledge of the relevant regulations, to be able to perform tasks assigned to

them and to detect and avoid any potential dangers independently.

■

Electricians have the specialist training, skills, and experience, as well as knowl‐

edge of the relevant standards and provisions to be able to carry out work on elec‐

trical systems and to detect and avoid any potential dangers independently. In Ger‐

many, electricians must meet the specifications of the BGV A3 Work Safety Regu‐

lations (e.g., Master Electrician). Other relevant regulations applicable in other

countries must be observed.

The following qualifications are required for various activities:

Tasks Qualification

Mounting, maintenance

■

Basic practical technical training

■

Knowledge of the current safety regulations in the workplace

Electrical installation,

device replacement

■

Practical electrical training

■

Knowledge of current electrical safety regulations

■

Knowledge of the operation and control of the devices in

their particular application

Commissioning,

Configuration

■

Basic knowledge of the design and setup of the described

connections and interfaces

■

Basic knowledge of data transmission

■

Knowledge of the operation and control of the devices in

their particular application

Operation of the device for

the specific application

■

Knowledge of the operation and control of the devices in

their particular application

■

Knowledge of the software and hardware environment in the

application

2.6 Hazard warnings and operational safety

Please observe the safety notes and the warnings listed here and in other chapters of

these operating instructions to reduce the possibility of risks to health and avoid dan‐

gerous situations.

2.7 Repairs

The product is a replacement device. The device is not intended to be repaired. Interfer‐

ence with or modifications to the device on the part of the customer will invalidate any

warranty claims against SICK AG.

SAFETY INFORMATION 2

8021879.ZZG2 | SICK

Subject to change without notice

9

3 Product description

3.1 Device view

6

5

7

1

2

3

4

Figure 1: Dimensional drawing

1

Green LED indicator: supply voltage active

2

Yellow LED indicator: status of received light beam

3

Fixing hole, Ø 3.2 mm

4

Cable / Cable with M8 male connector

5

Single teach-in button for setting the sensing range

6

Optical axis, receiver

7

Optical axis, sender

4 Mounting

4.1 Scope of delivery

•

Photoelectric proximity sensor with time-of-flight technology in the version ordered

•

Set of screws

•

Quickstart

•

Safety notes

4.2 Mounting requirements

•

Typical space requirement for the device, see type-specific dimensional drawing,

see „Dimensional drawings“, page 19.

•

Comply with technical data, such as the permitted ambient conditions for opera‐

tion of the device

3 PRODUCT DESCRIPTION

10

8021879.ZZG2 | SICK

Subject to change without notice

4.3 Mounting the device

L

Figure 2: Sensor alignment

Figure 3: Standard direction

0

85

(3.35)

30

(1.18)

125

(4.92)

0 200

(7.87)

400

(15.75)

600

(23.62)

800

(31.5)

Distance in mm (inch)

Min. distance from object to background in mm (inch)

2

1

6%/90%

90%/90%

Figure 4: Minimum distance from object to background

1

Sensing range on white, 90% remission

2

Object with 6 % ... 90 % remission (based on standard white DIN 5033)

1. Mount the sensor using a suitable mounting bracket (see the SICK range of acces‐

sories).

2. Note the sensor’s maximum permissible tightening torque of 0.5 Nm.

MOUNTING

4

8021879.ZZG2 | SICK

Subject to change without notice

11

3. Select the position so that the infrared light (not visible) hits the center of the

object. The correct alignment can only be detected via the LED indicators (yellow

indicator LED lights up when the object is detected) or with the help of an infrared

conversion screen (see the SICK range of accessories). see figure 2, page 11

4. Note the preferred direction of the object relative to the sensor. see figure 3,

page 11

5. Adjust the sensing range and distance to the object or background and the remis‐

sion capability of the object. see figure 4, page 11

6. You must ensure that the optical opening (front screen) of the sensor is completely

clear.

NOTE

The minimum distance for background suppression can be read as follows. Example:

Sensing range (= x axis) to a bright object is 400 mm. A dark background is suppressed

at a distance of 85 mm or more behind the object.

5 Electrical installation

5.1 Notes on the electrical installation

NOTICE

Equipment damage due to incorrect supply voltage!

An incorrect supply voltage may result in damage to the equipment.

■

Only operate the device with safety/protective extra-low voltage (SELV/PELV).

■

The sensor is a device of protection class III.

NOTICE

Equipment damage due to incorrect supply voltage!

An incorrect supply voltage may result in damage to the equipment.

•

Only operate the device with an LPS (limited power source) in accordance with IEC

60950-1 or an NEC Class 2 power supply unit.

NOTICE

Equipment damage or unpredictable operation due to working with live parts.

Working with live parts may result in unpredictable operation.

■

Only carry out wiring work when the power is off.

■

Only connect and disconnect electrical connections when the power is off.

■

The electrical installation must only be performed by electrically qualified person‐

nel.

■

Standard safety requirements must be met when working on electrical systems.

■

Only switch on the supply voltage for the device when the connection tasks have

been completed and the wiring has been thoroughly checked.

■

When using extension cables with open ends, ensure that bare wire ends do not

come into contact with each other (risk of short-circuit when supply voltage is

switched on!). Wires must be appropriately insulated from each other.

■

Wire cross-sections in the supply cable from the user’s power system must be

selected in accordance with the applicable standards.

■

Only operate the device with an LPS (limited power source) in accordance with IEC

60950-1 or an NEC Class 2 power supply unit.

■

All circuits connected to the device must be designed as SELV/PELV circuits.

■

Operation in short-circuit protected network at max. 8 A.

5 ELECTRICAL INSTALLATION

12

8021879.ZZG2 | SICK

Subject to change without notice

NOTE

Layout of data cables

■

Use shielded data cables with twisted-pair wires.

■

Implement the shielding design correctly and completely.

■

To avoid interference, e.g., from switching power supplies, motors, clocked drives,

and contactors, always use cables and layouts that are suitable for EMC.

■

Do not lay cables over long distances in parallel with voltage supply cables and

motor cables in cable channels.

The IP enclosure rating for the device is only achieved under the following conditions:

■

The cables plugged into the connections are screwed tight.

■

Any electrical connections that are not being used must be fitted with protective

caps that are screwed tight (as in the delivery condition).

■

Any other lids present must be closed and lie flush on the device.

If these instructions are not complied with, the IP enclosure rating for the device is not

guaranteed!

5.2 Pin assignment of the connections

Overview of pin assignment

Table 1: M12-Stecker, 4-polig

-2X329x -2X119x C-2Xxx9xAxx

1 +(L+) +(L+) +(L+)

2

Q Q

MF

3 -(M) -(M) -(M)

4 Q Q Q

1

/C

1

2

4 3

1 = BN

2 = WH

3 = BU

4 = BK

0.09 mm

2

AWG 28

1

2

4 3

1 = BN

2 = WH

3 = BU

4 = BK

0.09 mm

2

AWG 28

5.3

Connecting the supply voltage

NOTICE

Risk of damage to the device!

The device can become damaged if it is connected to a voltage supply that is already

switched on.

•

Only connect the device when the supply cable is de-energized.

The device must be connected to a power supply unit with the following properties:

•

Supply voltage DC 10.8 V – 28.8 V (SELV/PELV as per currently valid standards)

•

Electricity source with at least 3 W power

To ensure protection against short-circuits/overload in the customer’s supply cables,

the wire cross-sections used must be appropriately selected and protected.

ELECTRICAL INSTALLATION 5

8021879.ZZG2 | SICK

Subject to change without notice

13

6 Commissioning

6.1 Sensing range setting

Q1

Figure 5: Sensing range setting

1 Position the object at the required distance and move it into the beam path of the

device (note the min. and max. ranges, see figure 5, page 14).

2 The sensing range is adjusted by pressing the single teach-in button (yellow LED

lights up).

NOTE

Note: The sensor automatically places the switching point in the object (teach-in offset

15 mm). Exception: When manually adjusting a mm value using an IO-Link, we recom‐

mend placing the switching point in the object.

NOTE

We recommend making the adjustments using an object with a low remission.

NOTICE

Do not operate the teach-in button using sharp objects.

6.2 Switching behavior

PNP (ANT)

1

0

1

0

1

0

1

0

NPN (ANT)

Q\

Q

Q\

Q

Figure 6: Switching behavior

6 COMMISSIONING

14

8021879.ZZG2 | SICK

Subject to change without notice

If the switching output fails to behave in accordance with the above diagram, check the

application conditions. See section see figure 6, page 14 .

6.3 Additional functions

Information on the IO-Link functions can be found in the IO-Link index description for

photoelectric sensors which is available for download from www.sick.com (search for

the device’s part number).

Table 2: Process data structure (IO-Link version: V1.1 Process data length: 4 bytes)

No. Description Data type

Byte 0: bits 31...24

Byte 1: bits 23...16

Byte 2: bits 15...8

Byte 3: bits 7...0

Bit 0 Q

L1

Boolean

Bit 1 Q

L2

Boolean

Bit 2 Qint.1 Boolean

Bit 3 Qint.2 Boolean

Bits 4...15 Empty -

Bits 16...31 Analog value UInt16

7 Troubleshooting

Table 3: Fault diagnosis

Display, error situation Cause Measure

Green LED does not light up No voltage or voltage below

the limit values

Check the power supply, check

all electrical connections

(cables and plug connections)

Green LED does not light up Voltage interruptions Ensure there is a stable power

supply without interruptions

Green LED does not light up Sensor is faulty If the power supply is OK,

replace the sensor

Yellow LED flashes (only

briefly)

Teach-in mode Check the teach-in mode

Yellow LED flashes quickly

(only briefly)

Teach-in button lock active Deactivate the button lock

Yellow LED lights up, no object

in the path of the beam

Distance between the sensor

and the background is too

short

Reduce the sensing range, see

teach-in

Object is in the path of the

beam, yellow LED does not

light up

Distance between the sensor

and the object is too long or

sensing range is set too short

Increase the sensing range,

see teach-in

8 Maintenance

8.1 Maintenance

During operation, the device works maintenance-free.

Depending on the assignment location, the following preventive maintenance tasks

may be required for the device at regular intervals:

COMMISSIONING 6

8021879.ZZG2 | SICK

Subject to change without notice

15

Table 4: Maintenance schedule

Maintenance work Interval Implementation

Clean housing and front screen

Cleaning interval depends on ambi‐

ent conditions and climate

Specialist

Check screw connections and plug

connectors

Every 6 months Specialist

8.2 Cleaning the device

At regular intervals (e.g., weekly), check the light emission window and the housing of

the device for dirt. This is especially relevant in harsh operating environments (dust,

abrasion, damp, fingerprints, etc.). The lens of the light emission window must be kept

clean and dry during operation.

NOTICE

Device damage due to improper cleaning!

Improper cleaning may result in device damage.

■

Only use suitable cleaning agents.

■

Never use sharp objects for cleaning.

Cleaning the light emission window

NOTICE

Damage to the light emission window!

Reduced reading performance due to scratches or streaks on the light emission win‐

dow!

b

Clean the light emission window only when wet.

b

Use a mild cleaning agent that does not contain powder additives. Do not use

aggressive cleaning agents, such as acetone, etc.

b

Avoid any movements that could cause scratches or abrasions on the light emis‐

sion window.

b

Only use cleaning agents suitable for the screen material.

NOTE

Static charge may cause dust particles to stick to the light emission window. This effect

can be avoided by using an anti-static glass cleaner in combination with the SICK lens

cloth (can be obtained from www.sick.com).

NOTE

If the light emission window is scratched or damaged (cracked or broken), the device

must be replaced. Contact SICK Service to arrange this.

Cleaning the housing

In order to ensure that the heat produced by the internal power loss is adequately dissi‐

pated, the housing surface must be kept clean.

8 MAINTENANCE

16

8021879.ZZG2 | SICK

Subject to change without notice

9 Decommissioning

9.1 Disassembly and disposal

Disassembling the device

1. Switch off the supply voltage to the device.

2. Detach all connecting cables from the device.

3. If the device is being replaced, mark its position and alignment on the bracket or

surroundings.

4. Detach the device from the bracket.

Disposing of the device

Any device which can no longer be used must be disposed of in an environmentally

friendly manner in accordance with the applicable country-specific waste disposal regu‐

lations. As it is categorized as electronic waste, the device must never be disposed of

with household waste.

9.2 Returning devices

b

Do not dispatch devices to the SICK Service department without consultation.

NOTE

To enable efficient processing and allow us to determine the cause quickly, please

include the following when making a return:

■

Details of the contact person

■

Description of the application

■

Description of the fault that occurred

10 Technical data

10.1 Technical data

WTT2SL-2Xx92 WTT2SLC-2Xxx9xAxx

Laser class 1 1

Sensing range 50 ... 800 mm

1

50 ... 800 mm

1

Sensing range max. 50 ... 800 mm

1

50 ... 800 mm

1

Distance value-resolution - 1 mm

Distance value reproducibility - 2 mm ... 5 mm

2

Distance value-accuracy - ±20 mm

Light spot diameter/distance 10.0 mm / 300 mm 10.0 mm / 300 mm

Supply voltage V

S

DC 10 ... 30 V

3

DC 10 ... 30 V

3

Ripple ≤5 V

ss

≤5 V

ss

Current consumption ≤20 mA ≤20 mA

Output current I

max.

≤ 50 mA ≤ 50 mA

Max. switching frequency 5 Hz

4

5 Hz

4

Max. response time typ. 90 ms

5

,

6

typ. 95 ms

5

,

6

Input - MFin = multifunction

input programmable

DECOMMISSIONING 9

8021879.ZZG2 | SICK

Subject to change without notice

17

WTT2SL-2Xx92 WTT2SLC-2Xxx9xAxx

Enclosure rating IP 67 IP 67

Protection class III III

Circuit protection A, B, D

7

A, B, D

7

Ambient operating temperature -25 ... +50 °C

8

25 ... +50 °C

8

switching output PNP /NPN

9

PNP

Setting Single teach-in button

10

Single teach-in but‐

ton

10

, IO-Link

PIN2-Configuration - external teach, Teach-in

Input, Transmitter from

Input, detection output,

logic output

IO-Link - IO-Link V1.1

COM2 (38,4 kBaud)

Cycle time 5 ms

Process data length 4

Byte

Max. response time SIO Direct - typ. 90 ms

11

Max. response time SIO Logic - typ. 90 ms

12

Max. response time IOL - typ. 95 ms

13

Switching frequency SIO Direct - 5 Hz

11

Switching frequency SIO Logic - 5 Hz

12

Switching frequency IOL - 5 Hz

13

Inverter - YES

Smart Task label - Basis logic

Logic function - DIRECT

AND

OR

WINDOW

Hysteresis

Timer function - Deactivated

Switch-on delay

Switch-off delay

Switch-on and -off delay

Pulse (one shot)

1

Object with 6 % ... 90 % remission (based on standard white DIN 5033)

2

Equivalent to 1 σ.

3

Limit value; operation in short-circuit protection mains max. 8 A; residual ripple max. 5 V

ss

4

With light / dark ratio 1:1

5

Signal transit time with resistive load

6

Jitter± 20ms

7

A = U

V

-connections reverse polarity protected

B = inputs and output reverse-polarity protected

D = outputs overcurrent and short-circuit protected

8

As of T

U

= 45°C a max. output current of I

max

= 50 mA is permissible. Below T

U

= -10°C a warm-up time is necessary.

9

NPN off-state current I

R

<= 0.6 mA.

10

Footnote teach-in offset 15 mm

11

SIO Direct: Sensor operation in standard I / O mode without IO-Link communication and without the use of sensor-internal logic or time

parameters (set to "direct" / "inactive").

12

SIO Logic: Sensor operation in standard I / O mode without IO-Link communication. Use of sensor-internal logic or time parameters, addi‐

tional automation functions.

13

IOL: sensor operation with full IO-Link communication and use of logic, time and automation function parameters.

10 TECHNICAL DATA

18

8021879.ZZG2 | SICK

Subject to change without notice

10.2 Dimensional drawings

1

2

3

9

3

4

5

/

6

8

8 (0.31)

M8 x 1

Ø 3

(0.12)

13.5 (0.53)

4.2 (0.17)

10.8

(0.43)

3 (0.12)

11

(0.43)

15 (0.59)

24.6 (0.97)

max. 37 (1.46)

27.5 (1.08)

32.5 (1.28)

5

/

6

7

Figure 7: Dimensional drawing

1

Optical axis, receiver

2

Optical axis, sender

3

Fixing hole, Ø 3.2 mm

4

Connection

5

Green LED indicator: supply voltage active

6

Yellow LED indicator: status of received light beam

7

Cable

8

Single teach-in button

9

Cable with M8 male connector

TECHNICAL DATA 10

8021879.ZZG2 | SICK

Subject to change without notice

19

ページを読み込んでいます...

SICK PowerProx Micro - WTT2SL(C) 取扱説明書

関連論文

その他の書類