Red Sea ReefDose 2 ユーザーマニュアル

User Manual 2 & 4 Heads

ENG JP CHN

User Manual 2 & 4 Heads

Accurate – Smart - Intuitive

Red Sea ReefDose®

4

Contents

Introduction.................................................................................5

Safety .........................................................................................6

Device guide...............................................................................8

Installation...............................................................................10

Introduction to ReefBeat App.................................................12

Connection and initial setup...................................................13

Scheduling................................................................................20

Device manager.......................................................................26

Troubleshooting........................................................................30

Spare Parts list..........................................................................32

Warranty....................................................................................33

Red Sea ReefDose®

5

ENG

Introduction

Congratulations on your purchase of Red Sea’s ReefDose®.

The ReefDose was designed to cater to the specific needs of reef aquariums and reef hobbyists. ReefDose

employs highly precise, direct-drive dosing heads driven by high quality customized gear-motors, capable

of keeping a consistent daily dosing schedule to the accuracy of a single drop. ReefDose has 3 easy-set

fully automated daily dosing programs, another automated schedule for individually planned doses, and on-

demand manual dosing that is available at all times, for each supplement.

ReefDose is part of Red Sea’s suite of smart devices that are operated via Wi-Fi by Red Sea’s ReefBeat® App,

which needs to be installed on a smart mobile device with internet connectivity.

Welcome to Red Sea’s smart reef-keeping.

Sincerely,

The Red Sea Team

Red Sea ReefDose®

6

Safety

PLEASE READ AND FOLLOW ALL SAFETY INSTRUCTIONS

THIS DEVICE IS INTENDED FOR HOUSEHOLD AND INDOOR USE ONLY.

DANGER: To avoid possible electric shock, special care should be taken when handling a wet aquarium. For

each of the following situations, do not attempt repairs yourself; return the appliance to an authorized

service facility for service or discard the appliance.

WARNING: To guard against injury, basic safety precautions should be observed, including the following:

Do not operate any appliance if it has a damaged cord or plug, if it is malfunctioning, or if it is dropped or

damaged in any manner.

To avoid the possibility of the appliance, plug or receptacle getting wet, position the aquarium stand and tank

to one side of a wall-mounted receptacle to prevent water from dripping onto the receptacle or plug. You

should create a "drip loop" (see Figure 1) for each cord connecting an aquarium appliance to a receptacle. The

"drip loop" is that part of the cord below the level of the receptacle, or the connector. Use an extension cord, if

necessary, to prevent water traveling along the cord and coming into contact with the receptacle. If the plug or

receptacle does get wet, DO NOT unplug the cord. Disconnect the fuse or circuit breaker that supplies power to

the appliance. Then unplug the device and examine for presence of water in the receptacle.

This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if they

have been given supervision or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance

shall not be made by children without supervision.

The appliance is only to be used with the power supply unit

provided with the appliance.

To avoid injury, do not contact moving parts.

Always unplug an appliance from an outlet when not in use, before

putting on or taking off parts, and before cleaning. Never pull the

cord itself to remove the plug from the outlet. Grasp the plug and

pull to disconnect.

Red Sea ReefDose®

7

ENG

Specifications ReefDose® 2 ReefDose® 4

Number of dosing heads 2 4

Dimensions 13 x 10.5 x 8.5 cm

(5.1” x 4.1” x 3.4”)

22.5 x 10.5 x 8.5 cm

(8.9” x 4.1” x 3.4”)

Operating Temperature 5 to 45°C

Relative Humidity 15~85%RH

Supply voltage 100-240V 50/60Hz

Rating 1A, @10W Max.

Operating Voltage 12 Vdc

Operating Frequency 2402 - 2480 MHz

Max. Power 32.43 mW

Note: A cord rated for less amperes or watts than the appliance rating may overheat. Care should be

taken to arrange the cord so that it cannot be tripped over or pulled accidentally.

Do not use an appliance for anything other than its intended use.

The use of attachments not recommended or sold by the appliance manufacturer may cause unsafe conditions.

Do not install or store the appliance where it will be exposed to the weather or to temperatures below

freezing point.

Make sure an appliance mounted on a tank is securely installed before operating it.

Read and observe all the important notices on the appliance.

Red Sea ReefDose®

8

Device Guide

Power Supply

Only use the power supply provided with the product.

Plug the power supply into the wall outlet or suitable power center.

Connect the DC jack of the power supply to DC inlet on the back of the ReefDose. After powering on the

unit, the Power indicator LED of the ReefDose will switch on and the Setting Indicator LED will be off.

If the power indicator LED is not working, check that the power supply is properly inserted in the wall outlet

and it is switched on.

LED Indicators

Wi-Fi Settings

Buttons

Power

status LED

Wi-fi Status LED

AP name

Red Sea ReefDose®

9

ENG

Power Status Indicator LED

Red light DC power is available.

Wi-Fi Status Indicator LED

Solid Red light ReefDose is connected to the Home network.

Blinking Red light ReefDose is in Wi-Fi Access

Point (AP) mode (device can be discovered by Wi-Fi devices).

No Red light ReefDose Wi-Fi is off.

Double blink indicates change of status / end of process.

If indicator LED is off (ReefDose Wi-Fi is off):

Pressing button for 5 seconds (until double blink) activates Wi-Fi AP mode. The AP name is shown on the

back of the device.

If indicator LED is blinking (ReefDose Wi-Fi is in AP mode):

Pressing button for 5 seconds (until double blink) switches Wi-Fi off.

Clear Settings

Pressing the button for 15 seconds (until double blink) deletes all user settings. Complete the reset

process by disconnecting and reconnecting the DC power. (Note: before initiating "clear settings," delete

the specific ReefDose from ReefBeat via Device Manager.)

Wi-Fi Settings button and status LEDs

If indicator LED is on (ReefDose Wi-Fi is connected to a Wi-Fi network):

Pressing button for 5 seconds (until double blink) disconnects the ReefDose from the network and switches

it to Wi-Fi AP mode. (Note: before disconnecting a ReefDose from a network, delete the specific ReefDose

from ReefBeat via the Device Manager.)

Red Sea ReefDose®

10

Installation

The ReefDose unit is splashproof and designed to work inside an aquarium cabinet.

It is not waterproof and therefore it is not advisable to mount it directly above open water.

The ReefDose can be mounted directly of any vertical surface

using the mounting bracket provided, which should be

securely screwed to the surface. Self-adhesive pads are not

recommended.

Alternatively, the ReefDose may also be placed directly on

any at surface such as a shelf, on either its bottom, top, back

or both sides (see gure 2) without any impediment to its

functions and operation. If placed on its bottom surface, make

sure that the dosing tubes are not restricted in any way.

Before on-boarding the ReefDose to your ReefBeat, the individual head priming buttons are active so that you

can test that the heads are working and install the supplement containers and prime them ready for calibration.

Once the ReefDose is on-boarded to the App, the priming buttons are deactivated by default to prevent accidental

supplementing. They can be activated as and when required from the ReefBeat App as described below.

Red Sea ReefDose®

11

ENG

Connecting Heads to supplement containers

The dosing heads rotate in the clockwise direction. Connect a flexible tube from the supplement container to

the inlet (left hose-barb) of each dosing head. Connect a flexible tube to the head outlet (right hose barb)

and secure the end of the outlet tube in a suitable location above the sump.

The inlet and outlet hose barbs include lock nuts that are designed for flexible tubing with the approximate

internal diameter of 3mm (1/8”) and external diameter of 5mm (3/16” – ¼”).

It is highly recommended to use tubing that is highly impermeable to air such as the TPE tubing provided by

Red Sea. Regular silicone air-line will negatively affect the accuracy of the dosing.

To attach and secure the flexible tubing:

1. Remove the dosing head by gently squeezing

the top and bottom fasteners and pull it away

from the unit.

2. Rotate the lock-nut clockwise to the fully raised

position.

3. Push the flexible tube on to the hose barb until it

touches the lock-nut.

4. Rotate the lock-nut counter-clockwise over the

tube. Do not overtighten.

5. When the inlet and outlet tubes are secured in place push the head

back onto the unit. If necessary gently squeeze the top and/or

bottom fasteners to snap it into position.

Note: there is no need to align the head with the drive shaft as it has a mechanism that will automatically

engage when the head begins to rotate.

Priming buttons

Red Sea ReefDose®

12

Introduction to the ReefBeat App

All of Red Sea's connected devices must be operated via the ReefBeat App which must be installed on a

mobile device with an internet connection (including tablets). See the full list of supported mobile devices

on our website.

Through your personal user account on the cloud, ReefBeat enables you to set up and manage any number

of aquariums and add multiple devices to each of them.

For full functionality, each ReefDose must have a permanent connection to the internet through your home

Wi-Fi network. In this mode of operation, you will be able to see the current status of your ReefDose units,

change the settings or receive notications on your mobile whenever you have access to the internet.

The ReefBeat homepage will show you the current status of all of your connected devices, and links you

directly to the Settings Dashboard of each unit.

You can install the ReefBeat on multiple mobile devices by entering the same user account details. All

mobile devices will have the same rights for operating and changing all of the settings. You should keep this

in mind before giving your user details to any 3rd party.

In the event that you do not have a home network or your home network does not have an active internet

connection, you can connect and control your ReefDose units in Ofine or Direct Mode. However, certain

functionality such as remote access, multiple mobile devices or status notications will not be available.

ReefBeat is constantly under development. For the most up to date operation instructions, view or download

the latest user guide from the Red Sea website at www.redseash.com

If this is your rst Red Sea connected device, it is recommended that you complete the physical installation

of your ReefDose units before installing the ReefBeat App.

Red Sea ReefDose®

13

ENG

Connection and initial setup

Installing ReefBeat

Download ReefBeat from the App Store or Google Play, as appropriate for your mobile device (In countries

without access to Google Play, an APK file and installation instructions can be downloaded from Red Sea's

website).

After installing ReefBeat, you will be guided through the set-up of your ReefBeat user account and

aquariums, and then you can start adding your Red Sea connected devices. All of your user account details

can be edited only when your mobile is connected to the internet.

For full functionality Red Sea's connected devices should be connected to the internet and your aquariums

should be set to "Online". In the event that you do not have an available Wi-Fi network at your aquarium,

set it as "Offline". You can change this setting later when Wi-Fi becomes available.

Make sure that you select the correct world time zone for where your aquarium is located. The default is the

same time zone as your mobile which might be set for a different location. There is also a "Daylight Saving

Time" (DST) toggle that needs to be manually switched at the beginning and end of DST for your location.

If you've set up more than one aquarium, select the aquarium from the dropdown menu at the top of the

screen before proceeding.

Adding your first ReefDose to ReefBeat

Set your ReefDose to AP mode by pressing the settings button for 5 seconds (until double blink). The

indicator LED should be blinking.

Tap the Add Device button (+) from the Device Manager page, select the ReefDose 2/4 icon and follow the

instructions on the App.

• The AP name of the ReefDose should appear on your Wi-Fi settings screen. This may take a few

seconds. You will need to connect directly to the device and enter the password: “password”

• If no devices appear on the list, check that the ReefDose is in AP mode and/or refresh the page.

• If you have installed multiple ReefDose units and you have already activated the AP mode on all of

them, you will see a list of all of the ReefDose units. Choose any one of them as the first unit and

continue as instructed by the App.

Red Sea ReefDose®

14

Connecting to the Home Network

ReefBeat will now display a list of Wi-Fi networks and signal strengths that are available to the ReefDose from its

current location. Note: if the ReefDose is not in its intended operating location, your preferred network may not

be accessible when the ReefDose is repositioned.

Select your preferred network and wait a few moments while the ReefDose connects to it. The indicator LED will

now be a solid red. Follow the instructions on the App for initial settings.

Connecting without a Home Network (Direct Mode)

ReefBeat will now display a list of Wi-Fi networks and signal strengths that are available to the ReefDose in

its current location. Select the "Direct Mode" option at the top of the screen to skip the network connection

(See Connectivity Modes).

The indicator LED will continue to blink as the ReefDose Wi-Fi remains in AP mode. Follow the instructions

on the App for initial settings.

Note: If you are planning on using ReefDose with other Red Sea connected devices, it is recommended to

connect the ReefDose to a Wi-Fi network even if the network is not connected to the Internet and

the ReefDose will be operated in "Offline Mode". (See Connectivity Modes)

Red Sea ReefDose®

15

ENG

Connectivity Modes

For full functionality Red Sea's connected devices must be permanently connected to the Internet and the

aquarium set as "Online".

In the event that you do not have an available Wi-Fi network or your network does not have a permanent

internet connection set your aquarium as "Offline". You can change this setting later if Internet availability

status changes. Note that your mobile must be online for this change to be registered on the ReefBeat cloud.

In both Online and Offline modes, the ReefDose will provide exactly the same performance. The differences

are related to the ease of set up and interaction with other Red Sea connected devices.

Online (Internet) mode - full functionality

With a permanent connection to the internet, your ReefDose will have full functionality and all ReefBeat

cloud related services. This includes real time status of your ReefDose in the ReefBeat homepage and

notifications if communication with the ReefDose has been lost or if it is malfunctioning.

Offline Local Network mode - partial functionality

The ReefDose is connected to a home network without a permanent internet connection, and

aquarium is set as Offline.

In Offline mode, your mobile will need to be connected to the same network as your Red Sea

connected devices in order to communicate with them. When connected to the same network, you

will see the real time status on the homepage and have full functionality, except for Notifications,

which cannot be done offline.

When your mobile is not connected to the same network, no current data about the device will be

shown in the ReefBeat homepage. You can change the settings from Offline to Online from “My

Aquariums” in the homepage main menu.

Offline Direct mode - Limited functionality

If your ReefDose is not connected to a network, you will need to connect to its access point directly

from your mobile every time you wish to access it. When connected to the ReefDose in Direct mode,

you will not have any functionality that relates to other connected devices.

When your mobile is not connected to the ReefDose, no current data about the device will be shown in

the ReefBeat homepage. Notifications are not available for offline units.

When operating in direct mode, you can decide if you want to leave the ReefDose AP active all the

time or turn it on/off with the Settings button for access as needed.

At any point in time, you can connect a Direct mode unit to a Home Network: Device Manager > Device

Line menu > About > Connect.

Red Sea ReefDose®

16

Note: Each head needs to be set up individually before it can be programmed with an automated

schedule or give a manual dose. See the “Head Settings” section below.

Initial settings

The AP name of each ReefDose is the default name for the device in the App. However, you can set a new

name during the on-boarding or at a later time using the “Rename” function from the Device Manager.

Once ReefDose is successfully on-boarded to ReefBeat you are asked to set a few Device Settings and

notification settings for your ReefDose, all of which may be changed in the future from the 3-dots menu of

the Dashboard.

1. Device Settings

• “Supplement Volume Monitor”: enter the number of days for receiving low supplement notification.

Default is set at 3 days.

• “Delay Between Heads”: select a time gap between dosing of different heads, to prevent unwanted

chemical interactions. Minimum setting is 15 seconds (default), maximum is 5 minutes.

These settings can be edited at any time from: Dashboard > 3dots menu > Device Settings

2. Notifications Setup

Select which notifications you would like to receive to your mobile when the App is closed.

• “Head malfunction”: receive a notification if a head is missing or not attached properly during a

scheduled dose.

• “Missed dose”: receive a notification at 12:00 if scheduled doses from the previous day were not

compensated and you have not yet opened the App to see the automated pop-up.

• “Stock Level Monitor”: receive a notification when supplements need to be replenished.

These settings can be edited at any time from: Homepage > 3dots menu > Notification Settings

Red Sea ReefDose®

17

ENG

Adding additional ReefDose units

To connect an additional unit, open the Device Manager page from the Dashboard 3-dot menu and repeat the

process as above. Make sure that you connect all the units for one aquarium to the same home network.

Each unit will run independently of each other, therefore all supplements that may have a chemical interaction

if dosed together (such as calcium and KH) should be dosed from the same device.

Re-onboarding a deleted ReefDose unit

When on-boarding a ReefDose unit that was previously connected you are given the option of restoring all of

the previous settings.

ReefBeat Homepage

The ReefBeat homepage will show you the current status of all of your connected devices, and links you

directly to the settings Dashboard of your ReefDose. The homepage also has “Quick actions” buttons for

implementing frequent or important functions across all of the ReefBeat connected devices. The Quick

actions settings page and Device Manager are accessible from the 3-dot menu of the homepage.

If you have multiple ReefBeat devices, you can drag and drop the “device cards” to customize their order of

presentation in the homepage. You can also make the ReefDose card more compact by deciding which of

the heads details you want shown in the Homepage or even remove them all and just use it to access the

ReefDose dashboard.

Red Sea ReefDose®

18

Note: If you wish to change the supplement you are using in any given head, you must delete the head

then setup the head again from the beginning.

Homepage > Dashboard > Setup Head

Naming

If you are using Red Sea supplements, simply select from the drop-down list. If not, select “other” and enter a

supplement name of your choice. Please note that the first 3 letters of the name will be used to present this

supplement in the dosing log.

The information provided for the “other” supplements will automatically be added to your supplement library.

Priming

Priming fills the dosing tube with the supplement from the container to the tip of the dosing tube. Make sure

that the supplement is at the end of the outlet dosing tube before proceeding to the calibration.

The head can be primed either by pressing and holding the priming button on the device or by pressing

“Start” / “Stop” priming buttons in the App. To prevent accidents, the priming button in the App switches

off automatically after approximately 20ml which should be enough time to fill about 3m (10’) of tubing. If

necessary, you can restart the priming from the App as required.

ReefDose - head setup & calibration

Each individual dosing head needs to be set up before it can be used. The setup process for each head

includes defining the supplement and calibrating the head for that specific supplement. Calibration is

essential due to the varying viscosity of different supplements and the small differences in the components

of each head.

The calibration sets the exact volume of supplement that is dosed by each of the 3 rollers of the dosing

head and is normally in the range of 0.06 to 0.07 ml per roller.

In order for your head to work accurately, it must be calibrated the first time you use it to dose a new

supplement, then re-calibrated each time you replace the heads’ internal dosing tube. The accuracy of

the calibration will determine the accuracy of the dosing and therefore it is important to do this process

correctly. After initial head setup, each head can be recalibrated at any time either from the Head Setup

page or from the 3dots menu of the ReefDose dashboard Dashboard > 3dots menu > Recalibrate

Red Sea ReefDose®

19

ENG

Calibration

The instructions in the App will guide you through a simple calibration process using the laboratory grade

measuring cylinder provided with the unit.

Make sure that the measuring cylinder is clean and dry before each measurement as any drops left inside

will affect the accuracy of the reading.

Due to the physical properties of liquids the surface of the liquid inside a measuring cylinder is flat in the

middle but rise slightly at the sides. The correct measurement is at the center (lower part) of the surface

and not the sides.

The measuring cylinder has printed graduations every 0.1ml however you should estimate the volume to

the nearest 0.05ml which is half way between the printed graduations.

Always hold the tip of the dosing tube at the center of the cylinder so that the drops do not stick to the

cylinder walls.

During the calibration process the ReefDose doses a predetermined number of rotations of the dosing head

that should give a volume of between 4 and 5ml. Once you enter the exact volume into the App it will

give a confirmation dose of exactly 4ml so that you can confirm that the calibration was done correctly. The

confirmation dose should be between 3.95 and 4.05ml. If not, you will be guided to repeat the calibration

process again.

Inlet Outlet

Red Sea ReefDose®

20

Scheduling

Automatic Dosing Schedule

A selection of “quick-set” automated dosing schedules can be set to run for each head on a regular daily

basis, or on selected days of the week. Additional manual doses can be added at any time and without

disrupting an automated schedule. The schedule can also be switched on and off as required, without losing

your settings.

Single dose, Hourly dose and Custom Periods dose schedules are based on a desired total daily dose (total

amount of supplement that should be dosed per day) for each head. The schedule will divide the total daily

dose volume equally between the total number (1-24) doses per day, so that you can easily update your

daily dose volume anytime. Individual doses may vary by up to 1 drop throughout the day to ensure the

single drop accuracy for the complete daily dose. The total daily dose per head can be from 0.2ml up to

1000ml in increments of 0.1ml, however the smallest individual dose is limited to 0.2ml.

You can change the total daily dose or the number of doses whenever desired. ReefDose will automatically

recalculate the dosing schedule for the rest of the day and if necessary will present you with options

regarding how to proceed. For example, if you increase the daily dose in the middle of the day when some

doses have already been given and there are still some more doses to give, ReefBeat will prompt you to

choose between dosing the new volume per dose for the remaining doses of today, or increase them to

compensate for the doses that were already given at the previous volume.

The Timer schedule enables you to set up to 24 doses each with its unique volume and specific time. The

ReefBeat will present the total daily dose, however, this is the sum of the individual doses and therefore

any changes to the schedule need to be done at the level of the individually set doses. When setting a

timer schedule the new schedule will be implemented immediately, without taking into account any of the

doses that may have been given earlier.

The automatic schedules can operate on three possible Dosing rates:

1) Whisper – approximately 15ml/minute.

2) Regular – approximately 30ml/minute.

3) Turbo – approximately 45ml/minute.

The dosing rate selected In Single dose and Hourly dose is applied to all doses in the schedule. In Custom

dose, a dosing rate is selected for each time period. In Timer schedule, the dosing rate can be selected for

each individual dose.

The “Dynamic Dosing Queue” in the unit combines the setting for the individual heads into a coordinated

ページが読み込まれています...

Red Sea ReefDose 2 ユーザーマニュアル

このマニュアルも適しています

Red Sea ReefDose 2 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント