HP 9250C DIGITAL SENDER クイックスタートガイド

HP 9250C Digital Sender

Getting Started Guide

入门指南

Panduan Persiapan Awal

セットアップガイド

시작 설명서

คู่มือเริ่มต้นอย่างรวดเร็ว

入門指南

Hướng dẫn Sử dụng

0089/1.824.51

Terdaftar di Deperindag Provinsi DKI Jakarta No :

Copyright and License

Development Company, LP

Reproduction, adaptation, or translation

without prior written permission is prohibited,

except as allowed under the copyright laws.

The information contained in this document

is subject to change without notice.

The only warranties for HP products and

services are set forth in the express warranty

statements accompanying such products

and services. Nothing herein should be

construed as constituting an additional

warranty. HP shall not be liable for technical

or editorial errors or omissions contained

herein.

CB472-90942

Edition 1, 6/2007

FCC Regulations

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate

radio frequency energy. If this equipment is

not installed and used in accordance with the

instructions, it can cause harmful

interference to radio communications.

However, there is no guarantee that

interference will not occur in a particular

installation; the presence of interference can

be determined by turning the equipment off

and on.

If this equipment does cause harmful

interference to radio or television

communications, the user is encouraged to

try to correct the interference by one or more

of the following measures: Reorient or

relocate the receiving antenna; increase

distance between equipment and receiver;

connect equipment to an outlet on a circuit

different from that to which the receiver is

located; or consult your dealer or an

experienced radio/television technician.

Note: Any changes or modifications to the

device that are not expressly approved by

HP could void the user's authority to operate

this equipment

Trademark Credits

Microsoft® and Windows® are U.S.

registered trademarks of Microsoft

Corporation.

Pentium® is a registered trademark of Intel

Corporation or its subsidiaries in the United

States and other countries.

English

Install and Setup the Device

Installation environment

Prepare the site

Select a well-ventilated, dust-free area to install the device. Place the device on a sturdy surface.

552.62 mm (17.82 inches) 571.82 mm (22.51 inches)

340.26 mm (13

.40 inches)

340.26 mm (13

.4

0 inches)

System requirements

To install the HP 9250C Digital Sender, the computer system must have the following features:

●

Fast Ethernet 100Base-TX or Ethernet 10Base-T

●

Access to an SMTP e-mail gateway

NOTE HP highly recommends establishing SMTP gateway on your own local area network.

However, the device can be configured for e-mail functionality even if mail services are provided

by an outside Internet service provider (ISP) over a digital subscription line (DSL).

ENWW Installation environment 1

English

Device components

Unpack the device

Remove all shipping bags, tape, and packing material.

1

2

4

3

5

1 Getting started guide

2 Digital sender documentation and HP DSS optional software

3 Digital sender

4 Control panel overlays (if included)

5 Power cord

Identify device parts

Front of device

5

6

3

4

2

1

1. Control panel

2. Jam release

3. Output bin

4. ADF input tray

5. Keyboard (pull to open)

6. On/off switch

2 Install and Setup the Device ENWW

English

Control Panel

4

3

2

1

10

9

5

6

7

8

1. Attention light

2. Data light

3. Ready light

4. Brightness-adjustment dial

5. Touchscreen graphical display

6. Numeric keypad

7. Sleep button

8. Reset button

9. Stop button

10. Start button

Back of device, lock, and serial number

14

15

13

12

11

10

9

8

7

16

7. ADF cable

8. Control-panel cable

9. 10/100Base-T network port

10. EIO port

11. USB host port (for third-party accessories)

12. USB device port (if needed for firmware upgrades)

13. Power connector

14. Scanner lock

15. Serial number

16. Extra mylar sheets

ENWW Device components 3

English

Starting up

Changing the control panel overlays

Use the following procedure to change the control-panel overlay, if needed.

1. Insert a small, flat-blade tool in the slot at the top edge. Lift the top and pull it off the control panel.

2. Place the overlay to align correctly with the buttons. Slide the bottom edge down first and snap it

onto the control panel

Unlock the scanner

Connect the network cable

4 Install and Setup the Device ENWW

English

Connect the power cord

2

1

1. Connect the power cord to the device and outlet.

2. Turn on the power switch and follow the prompts on the control panel.

Configure the control-panel settings

Basic default settings

Language settings

After the device warms up, the messages on the control panel appear in English. Change the language

in one of two ways:

●

Select the preferred language from the Language menu the first time the device is turned on. The

language must be selected within 60 seconds after the menu appears.

or

●

Change the language at any time from the Administration menu. First touch Device Behavior,

touch Language, touch the preferred language, and then touch Save.

Date and time settings

Touch Exit if the date and time settings are correct. Touch OK to change these settings.

Assign the IP address

The device must be assigned a valid IP (Internet Protocol) address on the network. If the network uses

dynamic host configuration protocol (DHCP), the IP address can be assigned automatically. DHCP is

the default setting in the digital sender. Manually assign an IP address if DHCP is not being used.

Find the automatically assigned DHCP IP address

On the home screen, touch Network Address. The IP address appears on the Network Address screen.

If the Network Address button does not appear, find the IP address:

●

Touch Administration, and then touch Information.

●

Touch Configuration/Status Pages, and then touch Configuration Page.

●

Touch Show. The digital-sender configuration information appears.

●

Touch OK to see the Jetdirect data. Scroll through the information to find the IP address.

ENWW Configure the control-panel settings 5

English

Manually assign an IP address

1. Touch Administration, and then touch Initial Setup.

2. Touch Networking and I/O, and then touch Embedded Jetdirect.

3. Touch TCP/IP, and then touch either IPV4 Settings (such as http://192.168.1.1) or IPV6 (such as

http://[2001:0ba0:0000.0000.0000.0000.0000:1234]).

4. Touch Config Method.

5. Touch Manual, and then touch Save.

6. Touch Manual settings.

7. Touch IP address. Touch the IP address field, and then type the IP address.

8. Touch OK.

Device configuration

Before configuring, have the following information:

●

The host name or IP address of the simple mail transfer protocol (SMTP) e-mail server that will

send e-mail from the digital sender

●

The host name or IP address of the Lightweight Directory Access Protocol (LDAP) server that will

retrieve e-mail addresses (optional)

●

The preferred folder paths for the send-to-folder feature

●

The host name or IP address of the digital sender

Use the following keys on the keyboard to help navigate through the configuration screens.

●

Press the Escape key to return to the previous screen.

●

Press the Tab key to move the cursor to the next field.

6 Install and Setup the Device ENWW

English

Install and configure Embedded Web Server (EWS)

Install and configure EWS to access the following features:

●

E-mail

●

Folder

●

Addressing

●

Kerberos authentication

●

LDAP authentication

●

Group 1/Group 2 PIN authentication

1. Open a web browser and type the device IP address.

2. Select the Digital Sending tab and complete the General Settings information.

3. Select E-mail Settings and then type the SMTP server address.

If you are using an Internet Service Provider (ISP) for Internet access and e-mail you might need

to contact your ISP to obtain the SMTP server name, and to determine if you need to enter an

account name and password for SMTP authentication.

4. Select E-mail Address Book to enter frequently-used e-mail addresses and e-mail distribution

lists. The Fax Address Book and Fax Speed Dials are located in the left navigation area.

5. Select Send To Folder to set up one or more folder destinations for scanned documents.

Install and configure digital sending software (DSS)

Install and configure digital sending software (optional) to access the following features:

●

Workflow

●

OCR

●

Lanfax

●

Windows authentication

●

Lanfax authentication

●

Netware authentication

Tip If a previous version of HP DSS is already installed, save time by copying settings with the

copy settings feature in the MFP configuration tab when installing the newer device.

The digital sender must be on and connected to the network in order to successfully complete the

software installation process.

Install the software on the server that will be supporting the HP Digital Sending Software (HP DSS)

service. After installation, the HP DSS runs in the background as a service, starting automatically

whenever the server is restarted.

Verify the device installation

Test the installation and configuration using the E-Mail and Network Folder options on the control-

panel display.

1. Place a document face-up in the ADF or face-down on the flatbed glass.

2. Touch E-Mail.

3. Type the user name and password, if prompted.

ENWW Device configuration 7

English

4. If not prompted to log in, touch From: and then type an e-mail address.

5. Touch To: and then type the same e-mail address.

6. Touch OK and then press Start. The device scans the document and sends it to you as an e-mail

attachment.

7. Repeat this process using the Network Folder option, and verify that the file is sent to the correct

folder.

A successful test shows that the device will scan and send documents to the configured e-mail address

or folder.

If the device does not send the file correctly, verify the device installation and configuration.

Where to look for more information

Feature Description For more

information

Scan to E-mail Scan a document and send it to any e-mail address

EWS user guide

Scan to Folder Scan a document to one or more network folders

Address Book for E-mail and

Fax

Enter names, e-mail addresses, and fax numbers

User PIN Authentication Requires authorization to use device

LDAP Addressing Search an LDAP directory for names and e-mail

addresses

LDAP Authentication

Require user authentication to use specific features

Kerberos Authentication

DSS LANFax Route fax jobs via an existing LANFax

infrastructure

DSS support guide

DSS Send to Folder

Scan a document to one or more network folders.

DSS Workflow Capture information about scanned documents;

route documents to other applications

DSS Windows Negotiated

Authentication

Requires user authentication to use specific

features

DSS LDAP Authentication

8 Install and Setup the Device ENWW

English

Troubleshooting and customer support

Troubleshooting

Problem Action to take

The digital sender will not scan and is unable

to complete the job. A Please try again error

message is displayed.

●

The scanner head lock is still in the locked position. Switch it to the unlocked position.

See

Unlock the scanner.

The Find Servers button on the E-Mail

Settings screen did not find any servers.

●

Verify that you have a functioning SMTP server on the network.

●

Click the Add… button on the E-Mail Settings screen and type the host name or IP

address of the SMTP server. After typing the address, click the Test button to verify

that the software can contact the server.

●

If testing the server is unsuccessful, contact the network administrator to help

troubleshoot the communication with the server.

●

If you have any other digital senders or MFPs that are using the HP DSS service, use

the Copy Settings button on the MFP Configuration tab of the HP MFP DSS

Configuration Utility to copy the settings from a device that is functioning correctly, and

then use the Paste Settings button to apply those settings to the digital sender.

The Find Servers button on the

Authentication Settings screen did not find any

servers.

●

Verify that there is a functioning LDAP server on the network.

●

Type the host name or IP address of the LDAP server into the LDAP Server text box.

After typing in the address, touch Find Settings to retrieve the server settings. Then

touch Test to verify that the software can contact the server.

●

If testing the server is unsuccessful, contact the network administrator to help

troubleshoot the communication with the server.

●

If there are any other digital senders or MFPs that are using the HP DSS service, use

the Copy Settings button on the MFP Configuration tab of the HP MFP DSS

Configuration Utility to copy the settings from a device that is functioning correctly, and

then use the Paste Settings button to apply those settings to the digital sender.

The digital sender is not working.

●

Verify that the power cord is securely connected to the device and that it is plugged

into the power outlet.

●

Verify that the device is turned on.

●

Clear any error messages on the control-panel display.

●

Verify that the network cable is securely connected to the device.

●

Verify that one of the two green LEDs just above the device network port is on.

Scanned pages are blank or have repeated

patterns.

●

Verify that a page is not already located on the glass.

The image quality is poor.

●

Verify that the document that you are trying to send is placed correctly in the ADF (face-

up) or on the glass (face-down).

●

Try changing some of the scan settings, where possible, such as resolution or file type,

to improve the image quality.

The ADF feeds multiple sheets, skews sheets,

or jams frequently.

●

Adjust the guides so that they are snug against the stack but do not bend the stack.

●

Verify that the ADF input tray or output bin is not overloaded. Each tray can hold a

maximum of 50 pages, but this capacity may be lower when using certain types of

media.

●

Verify that the paper is stacked square and straight in the ADF.

ENWW Troubleshooting and customer support 9

English

Problem Action to take

●

If the original was previously stapled or three-hole-punched, make sure the pages are

not stuck together.

●

Verify that the type of media that is being loaded meets the required specifications.

See the HP 9250C Digital Sender User Guide for media specifications.

An e-mail transmission did not arrive at the

destination e-mail address.

●

If the e-mail address was manually typed, resend the e-mail message. Re-enter the e-

mail address, and verify that the correct format has been used (no spaces, the required

@ sign, the required period) in both the To: and From: text boxes.

●

Resend the e-mail. Type the name in the correct format in the From: field so that the

message is not rejected and so that you receive a message back if the e-mail

transmission fails.

●

Have the network administrator verify that SMTP Relay is enabled on the mail server

in order to allow sending to e-mail addresses outside of your company.

●

Have the network administrator verify that the SMTP server is functioning.

A document that you sent to a folder did not

arrive at the destination folder.

●

Resend the document.

●

Verify whether the file name might have been modified to resolve a duplicate-file-name

error.

The bottom of a page that you sent is cut off.

●

If the document was sent from the glass, the document page might be too long. The

maximum length for documents scanned from the glass is A4, or 210 x 297 mm (8.27

x 11.69 inches).

The control panel is using the wrong language.

●

Use the control-panel menu to set the correct language. See Language settings.

Customer support

See the HP 9250C Digital Sender User Guide on the CD-ROM. For HP Customer Care information, see

the support flyer that came with the device, or go to

www.hp.com/support/9250c.

10 Install and Setup the Device ENWW

English

版权与许可

Development Company, LP

除非版权法许可，否则，在事先未经书面许

可的情况下，严禁复制、改编或翻译本书。

本文档所含信息如有更改，恕不另行通知。

HP 产品和服务的保修仅以随该产品和服务提

供的书面保修声明为准。本文所述任何内容

均不应被视为附加保修。对任何技术或编辑

错误或本文所述内容的遗漏，HP 不承担任何

责任。

CB472-90942

Edition 1, 6/2007

FCC 规则

此设备经测试证明符合 FCC 规则第 15 部分

中关于 B 类数字设备的限制规定。在住宅区

安装时，这些限制为防止有害干扰提供了合

理保护。本设备可以产生、利用并发射无线

射频能量。如果不按说明中的要求安装和使

用本设备，有可能对无线电通信产生有害干

扰。但也不能保证在特定的安装中不会产生

干扰问题；可以通过开关设备的方法来确定

是否存在干扰。

如果本设备确实对无线电或电视接收造成干

扰，建议用户采取以下一种或多种措施排除

干扰：重新调整接收天线的方向或位置；增

加设备和接收器之间的距离；将本设备电源

插座与接收器电源插座设在不同的电路上；

咨询代理商或经验丰富的无线电/电视技术人

员。

注：未经 HP 公司的明确同意而擅自更改或

改动本设备，将取消用户对此设备的操作权

限。

商标说明

Microsoft® 和 Windows® 是微软公司在美国

的注册商标。

Pentium® 是 Intel Corporation 或其子公司在

美国和其他国家/地区的注册商标。

简体中文

安装和设置设备

安装环境

准备场地

选择一个通风良好的无尘区安装设备。将设备放在稳固表面上。

552.62 mm (17.82 inches) 571.82 mm (22.51 inches)

340.26 mm (13

.40 inches)

340.26 mm (13

.4

0 inches)

系统要求

要安装 HP 9250C 数字发送器，计算机系统必须具有以下功能：

●

快速以太网 100Base-TX 或以太网 10Base-T

●

可访问 SMTP 电子邮件网关

注意 HP

极力建议

在自有局域网中建立 SMTP 网关。然而，即使外部 Internet 服务提供商

(ISP) 通过数字用户线 (DSL) 提供邮件服务，也可以配置设备的电子邮件功能。

ZHCN

安装环境

1

简体中文

设备组件

拆开设备包装

拆除所有运输袋、胶带和包装材料。

1

2

4

3

5

1

入门指南

2

数字发送器文档和 HP DSS 可选软件

3

数字发送器

4

控制面板贴面（如果附带）

5

电源线

识别设备部件

设备前部

5

6

3

4

2

1

1. 控制面板

2. 卡塞解除

3. 出纸槽

4. ADF 进纸盘

5. 键盘（拉出即可打开）

6. 开关

2

安装和设置设备

ZHCN

简体中文

控制面板

4

3

2

1

10

9

5

6

7

8

1. 注意指示灯

2. 数据指示灯

3. 就绪指示灯

4. 亮度调节拨盘

5. 触摸屏图形显示屏

6. 数字小键盘

7. 睡眠按钮

8. 重置按钮

9. 停止按钮

10. 开始按钮

设备后部、锁和序列号

14

15

13

12

11

10

9

8

7

16

7. ADF 电缆

8. 控制面板电缆

9. 10/100Base-T 网络端口

10. EIO 端口

11. USB 主机端口（用于第三方附件）

12. USB 设备端口（如果固件升级需要的话）

13. 电源连接器

14. 扫描仪锁

15. 序列号

16. 附加聚酯薄膜

ZHCN

设备组件

3

简体中文

启动

更换控制面板贴面

如果需要，请按下列步骤更换控制面板贴面。

1.

将一个小的一字工具插入顶边的插槽中。提起顶盖，使其脱离控制面板。

2.

将贴面正确对准按钮。先向下滑动底边，然后将其贴在控制面板上。

解除锁定扫描仪

连接网线

4

安装和设置设备

ZHCN

简体中文

连接电源线

2

1

1.

将电源线的一端连接到设备，另一端连接到电源插座。

2.

打开电源开关，并按照控制面板上的提示进行操作。

ZHCN

启动

5

简体中文

配置控制面板设置

基本默认设置

语言设置

设备预热后，控制面板上的消息用英语显示。用下列两种方式之一更改语言：

●

首次打开该设备时从语言菜单中选择首选语言。必须在菜单出现后 60 秒内选择语言。

或

●

可以随时从管理菜单中更改语言。首先轻触设备动作，按语言，轻触首选语言，然后轻触保存。

日期和时间设置

如果日期和时间的设置正确，轻触退出。轻触确定以更改这些设置。

指定 IP 地址

必须在网络上为该设备指定有效 IP（Internet 协议）地址。如果网络使用动态主机配置协议 (DHCP)，

则可以自动指定 IP 地址。 DHCP 是数字发送器中的默认设置。如果未使用 DHCP，请手动指定 IP 地

址。

查找自动指定的 IP 地址

在主页屏幕上，轻触网络地址。 IP 地址出现在“网络地址”屏幕上。

如果没有显示网络地址按钮，请通过以下方式查找 IP 地址：

●

轻触管理，然后轻触信息。

●

轻触配置/状态页，然后轻触配置页。

●

轻触显示。随即出现数字发送器的配置信息。

●

轻触确定以查看 Jetdirect 数据。滚动浏览信息以找到 IP 地址。

手动指定 IP 地址

1.

轻触管理，然后轻触初始设置。

2.

轻触联网和 I/O，然后轻触嵌入式 Jetdirect。

3.

轻触 TCP/IP，然后轻触 IPV4 设置（如 http://192.168.1.1）或 IPV6（如 http://[2001:0ba0:0000.

0000.0000.0000.0000:1234]）。

4.

轻触配置方法。

5.

轻触手动，然后轻触保存。

6.

轻触手动设置。

7.

轻触 IP 地址。轻触 IP 地址字段，随后键入 IP 地址。

8.

轻触确定。

6

安装和设置设备

ZHCN

简体中文

ページを読み込んでいます...

HP 9250C DIGITAL SENDER クイックスタートガイド

関連論文