DeWalt DCG412 ユーザーマニュアル

DCG412

B

English (original instructions) 04

繁體中文 22

37

Copyright DeWALT

1

Figure 1

s

o

j

e

f

c

b

a

j

i

h

g

h

j

e

Figure 2

d

p

DCB182 only

2

Figure 4

k

m

l

n

i

h

g

d

k

m

l

i

n

> 3.7 MM (1/8")

< 3.7 mm (1/8")

Figure 3

g

h

Figure 5

f

d

3

b

a

Figure 6 Figure 7

ENGLISH

4

CORDLESS GRINDER

DCG412

Congratulations!

You have chosen a DeWALT tool. Years of

experience, thorough product development and

innovation make DeWALT one of the most reliable

partners for professional power tool users.

Technical Data

DCG412

Voltage V

DC

18

Power input W 405

No-load/rated speed min

-1

8000

Wheel diameter mm 125

Spindle diameter M10

Weight (without battery pack) kg 1.9*

* weight includes side handle and guard

Battery pack DCB180 DCB181 DCB182

Battery type Li-Ion Li-Ion Li-Ion

Voltage V

DC

18 18 18

Capacity A

h

3.0 1.5 4.0

Weight kg 0.64 0.35 0.61

Charger DCB105

Mains voltage V

AC

220-240 V

Battery type Li-Ion

Approx. charging min 30 55

time (1.5 Ah (3.0 Ah

battery packs) battery packs)

70

(4.0 Ah battery packs)

Weight kg 0.49

Charger DCB115

Mains voltage V

AC

220-240 V

Battery type Li-Ion

Approx. charging min 22 45

time (1.5 Ah (3.0 Ah

battery packs) battery packs)

60

(4.0 Ah battery packs)

Weight kg 0.5

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and

pay attention to these symbols.

DANGER: Indicates an imminently

hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING: Indicates a potentially

hazardous situation which, if not

avoided, could result in death or

serious injury.

CAUTION: Indicates a potentially

hazardous situation which, if not

avoided, may result in minor or

moderate injury.

NOTICE: Indicates a practice not

related to personal injury which, if

not avoided, may result in property

damage.

Denotes risk of electric shock.

Denotes risk of fire.

WARNING: To reduce the risk of injury,

read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings

and all instructions. Failure to follow

the warnings and instructions may result

in electric shock, fire and/or serious

injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the dust

or fumes.

ENGLISH

5

c) Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of

electric shock.

b) Avoid body contact with earthed or

grounded surfaces such as pipes,

radiators, ranges and refrigerators. There

is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the

risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a residual

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric

shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool while

you are tired or under the influence of

drugs, alcohol or medication. A moment of

inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off position before

connecting to power source and/or

battery pack, picking up or carrying the

tool. Carrying power tools with your finger

on the switch or energising power tools that

have the switch on invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotating

part of the power tool may result in personal

injury.

e) Do not overreach. Keep proper

footing and balance at all times. This

enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce

dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job

better and safer at the rate for which it

was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the switch

is dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or the battery pack from

the power tool before making any

adjustments, changing accessories, or

storing power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and

tool bits etc., in accordance with these

instructions taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

ENGLISH

6

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified

by the manufacturer. A charger that is

suitable for one type of battery pack may

create a risk of fire when used with another

battery pack.

b) Use power tools only with specifically

designated battery packs. Use of any

other battery packs may create a risk of

injury and fire.

c) When battery pack is not in use, keep it

away from other metal objects like paper

clips, coins, keys, nails, screws or other

small metal objects that can make a

connection from one terminal to another.

Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be

ejected from the battery, avoid contact.

If contact accidentally occurs, flush with

water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the

battery may cause irritation or burns.

6) SERVICE

a) Have your power tool serviced by a

qualified repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

ADDITIONAL SPECIFIC SAFETY RULES

Safety Instructions for All Operations

a) This power tool is intended to function as a

grinder, wire brush or cut-off tool. Read all

safety warnings, instructions, illustrations

and specifications provided with this power

tool. Failure to follow all instructions listed below

may result in electric shock, fire and/or serious

injury.

b) Operations such as sanding and polishing

are not recommended to be performed

with this power tool. Operations for which

the power tool was not designed may create

ahazard and cause personal injury.

c) Do not use accessories which are not

specifically designed and recommended

by the tool manufacturer. Just because the

accessory can be attached to your power tool,

it does not assure safe operation.

d) The rated speed of the accessory must be at

least equal to the maximum speed marked

on the power tool. Accessories running faster

than their rated speed can break and fly apart.

e) The outside diameter and the thickness of

your accessory must be within the capacity

rating of your power tool. Incorrectly sized

accessories cannot be adequately guarded or

controlled.

f) The arbour size of wheels, flanges, backing

pads or any other accessory must properly

fit the spindle of the power tool. Accessories

with arbour holes that do not match the

mounting hardware of the power tool will run

out of balance, vibrate excessively and may

cause loss of control.

g) Do not use a damaged accessory. Before

each use inspect the accessory such as

abrasive wheel for chips and cracks, backing

pad for cracks, tear or excess wear, wire

brush for loose or cracked wires. If power

tool or accessory is dropped, inspect for

damage or install an undamaged accessory.

After inspecting and installing an accessory,

position yourself and bystanders away from

the plane of the rotating accessory and run

the power tool at maximum no-load speed

for one minute. Damaged accessories will

normally break apart during this test time.

h) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection must

be capable of stopping flying debris generated

by various operations. The dust mask or

respirator must be capable of filtrating particles

generated by your operation. Prolonged

exposure to high intensity noise may cause

hearing loss.

i) Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken

accessory may fly away and cause injury

beyond immediate area of operation.

j) Hold power tool by insulated gripping

surfaces only, when performing an operation

where the cutting accessory may contact

hidden wiring or its own cord. Cutting

accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and

shock the operator.

k) Position the cord clear of the spinning

accessory. If you lose control, the cord may be

cut or snagged and your hand or arm may be

pulled into the spinning accessory.

ENGLISH

7

l) Never lay the power tool down until the

accessory has come to a complete stop. The

spinning accessory may grab the surface and

pull the power tool out of your control.

m) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

n) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside

the housing and excessive accumulation of

powdered metal may cause electrical hazards.

o) Do not operate the power tool near

flammable materials. Sparks could ignite these

materials.

p) Do not use accessories that require liquid

coolants. Using water or other liquid coolants

may result in electrocution or shock.

FURTHER SAFETY INSTRUCTIONS

FOR ALL OPERATIONS

Causes and Operator Prevention

of Kickback

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or

any other accessory. Pinching or snagging causes

rapid stalling of the rotating accessory which in turn

causes the uncontrolled power tool to be forced in

the direction opposite of the accessory’s rotation at

the point of the binding.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into the

surface of the material causing the wheel to climb

out or kick out. The wheel may either jump toward

or away from the operator, depending on direction

of the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these

conditions.

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given BELOW:

a) Maintain a firm grip on the power tool

and position your body and arm to allow

you to resist kickback forces. Always use

auxiliary handle, if provided, for maximum

control over kickback or torque reaction

during start-up. The operator can control

torque reaction or kickback forces, if proper

precautions are taken.

b) Never place your hand near the rotating

accessory. Accessory may kickback over your

hand.

c) Do not position your body in the area where

power tool will move if kickback occurs.

Kickback will propel the tool in direction

opposite to the wheel’s movement at the point

of snagging.

d) Use special care when working corners,

sharp edges etc. Avoid bouncing and

snagging the accessory. Corners, sharp

edges or bouncing have a tendency to snag the

rotating accessory and cause loss of control or

kickback.

e) Do not attach a saw chain woodcarving

blade or toothed saw blade. Such blades

create frequent kickback and loss of control.

Safety Warnings Speciﬁc for

Grinding and Abrasive Cutting-Off

Operations

a) Use only wheel types that are recommended

for your power tool and the specific guard

designed for the selected wheel. Wheels for

which the power tool was not designed cannot

be adequately guarded and are unsafe.

b) The guard must be securely attached to the

power tool and positioned for maximum

safety, so the least amount of wheel is

exposed towards the operator. The guard

helps to protect operator from broken wheel

fragments and accidental contact with wheel

and sparks that could ignite clothing.

c) Wheels must be used only for recommended

applications. For example: do not grind with

the side of cut-off wheel. Abrasive cut-off

wheels are intended for peripheral grinding, side

forces applied to these wheels may cause them

to shatter.

d) Always use undamaged wheel flanges

that are of correct size and shape for your

selected wheel. Proper wheel flanges support

the wheel thus reducing the possibility of wheel

breakage. Flanges for cut-off wheels may be

different from grinding wheel flanges.

e) Do not use worn down wheels from larger

power tools. Wheel intended for larger power

tool is not suitable for the higher speed of a

smaller tool and may burst.

ENGLISH

8

Additional Safety Warnings Speciﬁc

for Abrasive Cutting-Off Operations

a) Do not “jam” the cut-off wheel or apply

excessive pressure. Do not attempt to make

an excessive depth of cut. Overstressing the

wheel increases the loading and susceptibility to

twisting or binding of the wheel in the cut and

the possibility of kickback or wheel breakage.

b) Do not position your body in line with and

behind the rotating wheel. When the wheel,

at the point of operations, is moving away from

your body, the possible kickback may propel the

spinning wheel and the power tool directly at

you.

c) When wheel is binding or when interrupting

a cut for any reason, switch off the power

tool and hold the power tool motionless

until the wheel comes to a complete stop.

Never attempt to remove the cut-off wheel

from the cut while the wheel is in motion

otherwise kickback may occur. Investigate

and take corrective action to eliminate the cause

of wheel binding.

d) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed

and carefully reenter the cut. The wheel may

bind, walk up or kickback if the power tool is

restarted in the workpiece.

e) Support panels or any oversized workpiece

to minimise the risk of wheel pinching and

kickback. Large workpieces tend to sag under

their own weight. Supports must be placed

under the workpiece near the line of cut and

near the edge of the workpiece on both sides

of the wheel.

f) Use extra caution when making a “pocket

cut” into existing walls or other blind areas.

The protruding wheel may cut gas or water

pipes, electrical wiring or objects that can cause

kickback.

Safety Warnings Speciﬁc for Wire

Brushing Operations

a) Be aware that wire bristles are thrown by

the brush even during ordinary operation.

Do not overstress the wires by applying

excessive load to the brush. The wire bristles

can easily penetrate light clothing and/or skin.

b) If the use of a guard is recommended for

wire brushing, do not allow any interference

of the wire wheel or brush with the guard.

Wire wheel or brush may expand in diameter

due to work and centrifugal forces.

Additional Safety Information

• Threaded mounting of accessories must match

the grinder spindle thread. For accessories

mounted by flanges, the arbor hole of the

accessory must fit the locating diameter of

the flange. Accessories that do not match the

mounting hardware of the power tool will run

out of balance, vibrate excessively and may

cause loss of control.

• The grinding surface of the centre depressed

wheels must be mounted below the plane of

the guard lip. An improperly mounted wheel

that projects through the plane of the guard lip

cannot be adequately protected.

• Do not use Type 11 (flaring cup) wheels on

this tool. Using inappropriate accessories can

result in injury.

• Always use side handle. Tighten the handle

securely. The side handle should always be

used to maintain control of the tool at all times.

Residual Risks

In spite of the application of the relevant safety

regulations and the implementation of safety

devices, certain residual risks cannot be avoided.

These are:

– Impairment of hearing.

– Risk of personal injury due to flying particles.

– Risk of burns due to accessories becoming hot

during operation.

– Risk of personal injury due to prolonged use.

– Risk of dust from hazardous substances.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

Wear ear protection.

Wear eye protection.

DATE CODE POSITION (FIG. 1)

The date code (s), which also includes the year of

manufacture, is printed into the housing.

Example:

2012 XX XX

Year of Manufacture

ENGLISH

9

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual

contains important safety and operating instruc tions

for the DCB105 and DCB115 battery charger.

• Before using the charger, read all instructions

and cautionary markings on charger, battery

pack and product using the battery pack.

WARNING: Shock hazard. Do not allow

any liquid to get inside charger. Electric

shock may result.

CAUTION: Burn hazard. To reduce

the risk of injury, charge only DeWALT

rechargeable battery packs. Other types

of batteries may overheat and burst

resulting in personal injury and property

damage.

CAUTION: Children should be

supervised to ensure that they do not

play with the appliance.

NOTICE: Under certain conditions, with

the charger plugged in to the power

supply, the exposed charging contacts

inside the charger can be shorted by

foreign material. Foreign materials of

a conductive nature such as, but not

limited to, steel wool, aluminum foil or

any buildup of metallic particles should

be kept away from charger cavities.

Always unplug the charger from the

power supply when there is no battery

pack in the cavity. Unplug charger

before attempting to clean.

• DO NOT attempt to charge the battery pack

with any chargers other than the ones in

this manual. The charger and battery pack are

specifically designed to work together.

• These chargers are not intended for

any uses other than charging DeWALT

rechargeable batteries. Any other uses

may result in risk of fire, electric shock or

electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when

disconnecting charger. This will reduce risk

of damage to electric plug and cord.

• Make sure that cord is located so that it will

not be stepped on, tripped over or otherwise

subjected to damage or stress.

• Do not use an extension cord unless it

is absolutely necessary. Use of improper

extension cord could result in risk of fire,

electric shock or electrocution.

• When operating a charger outdoors, always

provide a dry location and use an extension

cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of

electric shock.

• Do not block the ventilation slots on the

charger. The ventilation slots are located

on the top and sides of the charger. Place

the charger in a position away from any heat

source.

• Do not operate charger with damaged cord

or plug — have them replaced immediately.

• Do not operate charger if it has received

a sharp blow, been dropped or otherwise

damaged in any way. Take it to an authorised

service centre.

• Do not disassemble the charger; take it to

an authorised service centre when service or

repair is required. Incorrect reassembly may

result in a risk of electric shock, electrocution or

fire.

• In case of damaged power supply cord the

supply cord must be replaced immediately by

the manufacturer, its service agent or similar

qualified person to prevent any hazard.

• Disconnect the charger from the outlet

before attempting any cleaning. This will

reduce the risk of electric shock. Removing

the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on

standard 220-240 V household electrical

power. Do not attempt to use it on any other

voltage. This does not apply to the vehicular

charger.

SAVE THESE INSTRUCTIONS

Chargers

The DCB105 and DCB115 charger accepts 10.8 V,

14.4 V and18 V Li-Ion (DCB121, DCB123, DCB140,

DCB141, DCB142, DCB180, DCB181 and

DCB182) battery packs.

This charger requires no adjustment and is designed

to be as easy as possible to operate.

Charging Procedure (ﬁg. 2)

1. Plug the charger into an appropriate 220-240 V

outlet before inserting the battery pack.

2. Insert the battery pack (j) into the charger,

making sure the pack is fully seated in the

charger. The red (charging) light will blink

ENGLISH

10

continuously indicating that the charging

process has started.

3. The completion of charge will be indicated by

the red light remaining ON continuously. The

pack is fully charged and may be used at this

time or left in the charger.

NOTE: To ensure maximum performance and life of

Li-Ion batteries, charge the battery pack fully before

first use.

Charging Process

Refer to the table below for the state of charge of

the battery pack.

Charge indicators: DCB105

charging

fully charged

hot/cold pack delay

x

replace battery pack

Charge indicators: DCB115

charging

fully charged

hot/cold pack delay*

This charger will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing to

light or by displaying problem pack or charger blink

pattern.

NOTE: This could also mean a problem with a

charger.

If the charger indicates a problem, take the charger

and battery pack to be tested at an authorised

service centre.

Hot/Cold Pack Delay

When the charger detects a battery that is too hot

or too cold, it automatically starts a hot/cold pack

delay, suspending charging until the battery has

reached an appropriate temperature. The charger

then automatically switches to the pack charging

mode. This feature ensures maximum battery life.

XR Li-Ion tools are designed with an Electronic

Protection System that will protect the battery

against overloading, overheating or deep discharge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the

Li-Ion battery on the charger until it is fully charged.

A cold battery pack will charge at about half the rate

of a warm battery pack. The battery pack will charge

at that slower rate throughout the entire charging

cycle and will not return to maximum charge rate

even if the battery warms.

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure

to include the catalog number and voltage.

The battery pack is not fully charged out of the

carton. Before using the battery pack and charger,

read the safety instructions below and then follow

the charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use the battery pack

in explosive atmospheres, such as in the

presence of flammable liquids, gases or

dust. Inserting or removing the battery pack

from the charger may ignite the dust or fumes.

• Never force the battery pack into charger.

Do not modify the battery pack in any way

to fit into a non-compatible charger as

battery pack may rupture causing serious

personal injury.

• Charge the battery packs only in designated

DeWALT chargers.

• DO NOT splash or immerse in water or other

liquids.

• Do not store or use the tool and battery

pack in locations where the temperature

may reach or exceed 40˚C (105˚F) (such as

outside sheds or metal buildings in summer).

• For best results, make sure the battery pack is

fully charged before use.

WARNING: Never attempt to open

the battery pack for any reason. If

the battery pack case is cracked or

damaged, do not insert it into the

charger. Do not crush, drop or damage

battery pack. Do not use a battery

pack or charger that has received a

sharp blow, been dropped, run over

or damaged in any way (e.g., pierced

with a nail, hit with a hammer, stepped

on). Electric shock or electrocution may

result. Damaged battery packs should

be returned to the service centre for

recycling.

CAUTION: When not in use, place

tool on its side on a stable surface

where it will not cause a tripping or

falling hazard. Some tools with large

battery packs will stand upright on the

ENGLISH

11

battery pack but may be easily knocked

over.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION

(Li-Ion)

• Do not incinerate the battery pack even if it

is severely damaged or is completely worn

out. The battery pack can explode in a fire.

Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with

the skin, immediately wash the area with

mild soap and water. If the battery liquid gets

into the eye, rinse water over the open eye for

15 minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte

is composed of a mixture of liquid organic

carbonates and lithium salts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If

symptoms persists, seek medical attention.

WARNING: Burn hazard. Battery liquid

may be flammable if exposed to spark

or flame.

Battery Pack

BATTERY TYPE

The DCG412 operates on 18 volt battery pack.

The DCB180, DCB181 or DCB182 battery packs

may be used. Refer to Technical Data for more

information.

Storage Recommendations

1. The best storage place is one that is cool and

dry away from direct sunlight and excess heat

or cold. For optimum battery performance and

life, store battery packs at room temperature

when not in use.

2. For long storage, it is recommended to store a

fully charged battery pack in a cool, dry place

out of the charger for optimal results.

NOTE: Battery packs should not be stored

completely depleted of charge. The battery pack will

need to be recharged before use.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual,

the labels on the charger and the battery pack show

the following pictographs:

Read instruction manual before use.

Charging.

Fully charged.

Hot/cold pack delay.

x

Problem pack or charger.

Problem powerline.

Do not probe with conductive objects.

Do not charge damaged battery packs.

Use only with DeWALT battery packs.

Others may burst, causing personal injury

and damage.

Do not expose to water.

Have defective cords replaced

immediately.

Charge only between 4° C and 40° C.

Discard the battery pack with due care for

the environment.

Do not incinerate the battery pack.

Charges Li-Ion battery packs.

See Technical data for charging time.

Only for indoor use.

Package Contents

The package contains:

1 Angle grinder

1 125 mm Guard (Type 27)

1 Side handle

1 Flange set

1 Two-pin spanner

ENGLISH

12

1 Charger

2 Li-Ion battery packs (M2, L2 models)

1 Instruction manual

NOTE: Battery packs, chargers and kitboxes are not

included with N-models.

• Check for damage to the tool, parts or

accessories which may have occurred during

transport.

• Take the time to thoroughly read and

understand this manual prior to operation.

Description (ﬁg. 1–6)

WARNING: Never modify the power

tool or any part of it. Damage or

personal injury could result.

a. Trigger switch

b. Lock-off button

c. Spindle lock button

d. Spindle

e. Side handle

f. Abrasive wheel

g. Backing flange

h. Threaded clamp nut

i. Guard

j. Battery pack

k. Guard catch

l. Lugs

m. Gear case slots

n. Adjusting screw

o. Battery release button

p. fuel gauge button (DCB182 only)

INTENDED USE

The DCG412 heavy-duty angle grinder has been

designed for professional grinding and cutting

applications.

DO NOT use grinding wheels other than centre

depressed wheels and flap discs.

DO NOT use under wet conditions or in the

presence of flammable liquids or gases.

This heavy-duty angle grinder is a professional

power tools.

DO NOT let children come into contact with the

tool. Supervision is required when inexperienced

operators use this tool.

• This product is not intended for use by persons

(including children) suffering from diminished

physical, sensory or mental abilities; lack of

experience, knowledge or skills unless they are

supervised by a person responsible for their

safety. Children should never be left alone with

this product.

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the battery pack

voltage corresponds to the voltage on the rating

plate. Also make sure that the voltage of your

charger corresponds to that of your mains.

Your DeWALT charger is double insulated

in accordance with IEC 60335; therefore

no earth wire is required.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

DeWALT service organisation.

Using an Extension Cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see Technical Data). The minimum conductor size

is 1 mm

2

; the maximum length is 30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

WARNING: Use only DeWALT battery

packs and chargers.

Inserting and Removing the

Battery Pack from the Tool (ﬁg. 2)

NOTE: For best results, make sure your battery

pack is fully charged.

TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE

1. Align the battery pack (j) with the rails inside the

tool’s handle (fig. 2).

ENGLISH

13

2. Slide it into the handle until the battery pack is

firmly seated in the tool and ensure that it does

not disengage.

TO REMOVE THE BATTERY PACK FROM THE TOOL

1. Press the battery release button (o) and firmly

pull the battery pack out of the tool handle.

2. Insert battery pack into the charger as

described in the charger section of this manual.

FUEL GAUGE BATTERY PACKS (FIG. 2)

Some DeWALT battery packs include a fuel gauge

which consists of three green LED lights that

indicate the level of charge remaining in the battery

pack.

To actuate the fuel gauge, press and hold the fuel

gauge button (p). A combination of the three green

LED lights will illuminate designating the level of

charge left. When the level of charge in the battery

is below the usable limit, the fuel gauge will not

illuminate and the battery will need to be recharged.

NOTE: The fuel gauge is only an indication of the

charge left on the battery pack. It does not indicate

tool functionality and is subject to variation based

on product components, temperature and end-user

application.

Attaching Side Handle (ﬁg. 1)

WARNING: Before using the tool,

check that the handle is tightened

securely.

WARNING: The side handle should

always be used to maintain control of

the tool at all times.

Screw the side handle (e) tightly into one of the holes

on either side of the gear case.

To improve user comfort, the gear case will rotate

90° for cutting operations.

Rotating the Gear Case (ﬁg. 1)

1. Remove the four corner screws attaching the

gear case to motor housing.

2. Without separating the gear case from motor

housing, rotate the gear case head to desired

position.

NOTE: If the gear case and motor housing become

separated by more than 1/8" (3.17 mm), the

tool must be serviced and re-assembled by an

authorised DeWALT service center. Failure to have

the tool serviced may cause brush, motor and

bearing failure.

3. Reinstall screws to attach the gear case to the

motor housing. Tighten screws to 20 in.-lbs.

torque. Overtightening could cause screws to

strip.

Mounting and Removing the Guard

(ﬁg. 3)

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

CAUTION: Guards must be used with

this grinder.

When using the DCG412 grinder for cutting

metal or masonry a Type 1 guard MUST be used.

Type 1 guards are available at extra cost from

DeWALT distributors.

NOTE: Please refer to the Grinding and Cutting

Accessory Chart at the end of this section to

see other accessories that can be used with these

grinders.

1. Place the tool on a table, spindle (d) up.

2. Open the guard latch (k), and align the lugs (l)

on the guard with the slots on the gear

case (m).

3. Push the guard down until the guard lugs

engage and rotate freely in the groove on the

gear case hub.

4. With the guard latch open, rotate the guard (i)

into the desired working position.

5. Close the guard latch to secure the guard on

the gear case.

CAUTION: If the guard cannot be

tightened by the adjusting screw (n), do

not use the tool. To reduce the risk of

personal injury, take the tool and guard

to a service center to repair or replace

the guard.

NOTICE: Do not tighten the adjusting

screw (n) with the clamp lever in the

open position. Undetectable damage

to the guard or the mounting hub may

result.

NOTE: Edge grinding and cutting can be performed

with Type 27 wheels designed and specified for this

purpose; 6.35 mm (1/4") thick wheels are designed

for surface grinding while 3.17 mm (1/8") wheels are

designed for edge grinding.

ENGLISH

14

Mounting Depressed Center Grinding

Wheels

NOTE: The Type 27 guard supplied with grinder

MUST be used.

MOUNTING AND REMOVING HUBBED WHEELS (FIG. 1, 4)

Hubbed wheels install directly on the M10 threaded

spindle.

1. Thread the wheel on the spindle (d) by hand.

2. Depress the spindle lock button (c) and use a

wrench to tighten the hub of the wheel.

3. Reverse the above procedure to remove the

wheel.

NOTICE: Failure to properly seat the

wheel before turning the tool on may

result in damage to the tool or the

wheel.

MOUNTING NON-HUBBED WHEELS (FIG. 1, 4)

NOTE: The Type 27 guard supplied with grinder

MUST be used.

NOTE: Please refer to the Grinding and Cutting

Accessory Chart at the end of this section to

see other accessories that can be used with these

grinders.

1. Place the tool on a table, guard up.

2. Install the unthreaded backing flange (g) on

spindle (d) with the raised centre against the

wheel.

3. Place wheel (f) against the backing flange,

centering the wheel on the raised centre of the

backing flange.

4. While depressing the spindle lock button (c),

thread the clamp nut (h) on spindle. If the

wheel you are installing is more than 1/8"

(3.17mm) thick, place the threaded clamp nut

on the spindle so that the raised centre fits into

the center of the wheel. If the wheel you are

installing is 1/8" (3.17 mm) thick or less, place

the threaded clamp nut on the spindle so that

the raised centre is not against the wheel.

5. While depressing the spindle lock button (c),

tighten the clamp nut with a wrench.

6. To remove the wheel, depress the spindle lock

button and loosen the threaded clamp nut with

a wrench.

NOTE: If the wheel spins after the clamp nut is

tightened, check the orientation of the threaded

clamp nut. If a thin wheel is installed with the

raised centre on the clamp nut against the wheel,

it will spin because the height of the raised centre

prevents the clamp nut from holding the wheel.

Mounting Wire Brushes and Wire

Wheels (ﬁg. 1)

Wire cup brushes or wire wheels install directly on

the threaded spindle without the use of flanges.

Use only wire brushes or wheels provided with a

M10 threaded hub. These accessories are available

at extra cost from your local dealer or authorised

service center.

NOTE: The Type 27 guard is required when using

wire brushes and wheels.

CAUTION: To reduce the risk of

personal injury, wear work gloves

when handling wire brushes and

wheels. They can become sharp.

CAUTION: To reduce the risk

of damage to the tool, wheel

or brush must not touch guard

when mounted or while in use.

Undetectable damage could occur

to the accessory, causing wires to

fragment from accessory wheel or cup.

MOUNTING WIRE CUP BRUSHES AND WIRE WHEELS

1. Place the tool on a table, guard up.

2. Thread the wheel on the spindle by hand.

3. Depress spindle lock button (c) and use a

wrench on the hub of the wire wheel or brush to

tighten the wheel.

4. To remove the wheel, reverse the above

procedure.

NOTICE: To reduce the risk of damage

to the tool, properly seat the wheel hub

before turning the tool on.

Mounting Cutting (Type 1) Wheels

Cutting wheels include diamond wheels and

abrasive discs. Abrasive cutting wheels for metal

and concrete use are available. Diamond blades

for concrete cutting can also be used. These

accessories are available at extra cost from your

local dealer or authorised service center.

WARNING: A closed, two-sided cutting

wheel guard is re quired when using

cutting wheels. These accessories are

available at extra cost from your local

dealer or authorised service center.

Fail ure to use proper flange and guard

can re sult in injury resulting from wheel

breakage and wheel contact. Please

refer to the Grinding and Cutting

Accessory Chart at the end of this

ENGLISH

15

section to see other accessories that

can be used with these grinders.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

MOUNTING CLOSED (TYPE 1) GUARD (FIG. 5)

1. Open the guard latch (k), and align the lugs (l)

on the guard with the slots on the gear case

(m). This will align the lugs with slots on the gear

case cover. Position the guard facing backward.

2. Push the guard down until the guard lug

engages and rotates freely in the groove on the

gear case hub.

3. Rotate guard (i) into desired working position.

The guard body should be positioned between

the spindle and the operator to provide

maximum operator protection.

4. Close the guard latch to secure the guard on

the gear case cover. You should be unable to

rotate the guard by hand when the latch is in

closed position. Do not operate grinder with a

loose guard or clamp lever in open position.

5. To remove the guard, open the guard latch,

rotate the guard so that the arrows are aligned

and pull up on the guard.

NOTE: The guard is pre-adjusted to the dia met er of

the gear case hub at the factory. If, after a period of

time, the guard becomes loose, tighten the adjusting

screw (n) with the clamp lever in the closed position

with guard installed on the tool.

NOTICE: To reduce the risk of

damage to the tool, do not tighten

adjusting screw (n) with clamp lever in

open position. Undetectable damage to

guard or mounting hub may result.

MOUNTING CUTTING WHEELS (FIG. 1, 4)

CAUTION: Matching diameter backing

flange and clamp nut (included with

tool) must be used for cutting wheels.

1. Place the unthreaded backing flange on

spindle with the raised centre facing up. The

raised centre on the backing flange will be

against the wheel when the wheel is installed.

2. Place the wheel on the backing flange,

centering the wheel on the raised centre.

3. Install the threaded clamp nut with the raised

centre away from the wheel.

4. Depress the spindle lock button (c) and tighten

clamp nut with a wrench.

5. To remove the wheel, depress the spindle lock

button and loosen the threaded clamp nut with

a wrench.

Prior to Operation

• Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

• Be sure the inner and outer flanges are

mounted correctly.

• Make sure the disc or wheel rotates in the

direction of the arrows on the accessory and

the tool.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

WARNING:

• Ensure all materials to be ground or

cut are secured in place.

• Use clamps or a vice to hold

and support the workpiece to a

stable platform. It is important to

clamp and support the workpiece

securely to prevent the movement

of the workpiece and loss of control.

Movement of the workpiece or loss

of control may create a hazard and

cause personal injury.

• Apply only a gentle pressure to the

tool. Do not exert side pressure on the

disc.

• Always wear regular working gloves

while operating this tool.

• The gear case becomes very hot

during use.

• Always install the guard and

appropriate disc or wheel. Do not use

excessively worn disc or wheel.

ENGLISH

16

• Be sure the inner and outer flange are

mounted correctly.

• Make sure the disc or wheel rotates

in the direction of the arrows on the

accessory and the tool.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no-load condition.

Proper Hand Position (ﬁg. 1, 6)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the side

handle (e), with the other hand on the body of the

tool, as shown in figure 6.

Switch

WARNING: Before using the tool,

check that the handle is tightened

securely.

LOCK-OFF BUTTON AND TRIGGER SWITCH (FIG. 7)

Your cut-off tool is equipped with a lock-off

button(b).

To lock the trigger switch (a), press the lock-off

button as shown in figure 7. When the lock-off

button is depressed to the lock icon, the unit is

locked.

Always lock the trigger switch when carrying or

storing the tool to eliminate unintentional starting.

To unlock the trigger switch, press the lock-off

button (b). When the lock-off button is depressed

to the unlock icon, the unit is unlocked. The lock-off

button is colored red to indicate when the switch is

in its unlocked position.

Pull the trigger switch (a) to turn the motor ON.

Releasing the trigger switch turns the motor OFF.

NOTE: This tool has no provision to lock the switch in

the ON position, and should never be locked ON by

any other means.

WARNING: Hold the side handle and

body of the tool firmly to maintain

control of the tool at start up and during

use and until the wheel or accessory

stops rotating. Make sure the wheel has

come to a complete stop be fore laying

the tool down.

WARNING: Allow the tool to reach full

speed before touching tool to the work

surface. Lift the tool from the work

surface before turning the tool off.

Spindle Lock (ﬁg. 1)

The spindle lock (c) is provided to prevent the

spindle from rotating when installing or removing

wheels. Operate the spindle lock only when the tool

is turned off, unplugged from the power supply, and

has come to a complete stop.

NOTICE: To reduce the risk of damage

to the tool, do not engage the spindle

lock while the tool is operating. Damage

to the tool will result and attached

accessory may spin off possibly

resulting in injury.

To engage the lock, depress the spindle lock button

(c) and rotate the spindle until you are unable to

rotate the spindle further.

Using Depressed Center Grinding

Wheels

SURFACE GRINDING WITH GRINDING WHEELS

1. Allow the tool to reach full speed before

touching the tool to the work surface.

2. Apply minimum pressure to the work surface,

allowing the tool to operate at high speed.

Grinding rate is greatest when the tool operates

at high speed.

3. Maintain a 20° to 30° angle between the tool

and work surface.

4. Continuously move the tool in a forward and

back motion to avoid creating gouges in the

work surface.

5. Remove the tool from work surface before

turning tool off. Allow the tool to stop rotating

before laying it down.

EDGE GRINDING WITH GRINDING WHEELS

WARNING: Wheels used for cutting

and edge grinding may break or

kickback if they bend or twist while the

tool is being used to do cut-off work

or deep grinding. To reduce the risk

of serious injury, limit the use of these

wheels with a standard Type 27 guard

to shallow cutting and notching (less

than 1/2" [13 mm] in depth). The open

side of the guard must be positioned

away from the operator. For deeper

ENGLISH

17

cutting with a Type 1 cut-off wheel, use

a closed Type 1 guard. Please refer to

the Grinding and Cutting Accessory

Chart at the end of this section to see

other accessories that can be used with

these grinders.

1. Allow the tool to reach full speed before

touching the tool to the work surface.

2. Apply minimum pressure to the work surface,

allowing the tool to operate at high speed.

Grinding rate is greatest when the tool operates

at high speed.

3. Position yourself so that the open-underside of

the wheel is facing away from you.

4. Once a cut is begun and a notch is established

in the workpiece, do not change the angle of

the cut. Changing the angle will cause the wheel

to bend and may cause wheel breakage. Edge

grinding wheels are not designed to withstand

side pressures caused by bending.

5. Remove the tool from the work surface before

turning the tool off. Allow the tool to stop

rotating before laying it down.

WARNING: Do not use edge grinding/

cutting wheels for surface grinding

applications because these wheels

are not designed for side pressures

encountered with surface grinding.

Wheel breakage and serious personal

injury may result.

Mounting and Using Wire Brushes

and Wire Wheels

Wire wheels and brushes can be used for removing

rust, scale and paint, and for smoothing irregular

surfaces.

NOTE: Please refer to Precautions To Take When

Wire Brushing Paint.

1. Allow the tool to reach full speed before

touching the tool to the work surface.

2. Apply minimum pressure to work surface,

allowing the tool to operate at high speed.

Material removal rate is greatest when the tool

operates at high speed.

3. Maintain a 5° to 10° angle between the tool and

work surface for wire cup brushes.

4. Maintain contact between the edge of the wheel

and the work surface with wire wheels.

5. Continuously move the tool in a forward and

back motion to avoid creating gouges in the

work surface. Allowing the tool to rest on the

work surface without moving, or moving the tool

in a circular motion causes burning and swirling

marks on the work surface.

6. Remove the tool from the work surface before

turning the tool off. Allow the tool to stop

rotating before setting it down.

CAUTION: Use extra care when

working over an edge, as a sudden

sharp movement of grinder may be

experienced.

Using Cutting (Type 1) Wheels

WARNING: Do not use edge grinding/

cutting wheels for surface grinding

applications because these wheels

are not designed for side pressures

encountered with surface grinding.

Wheel breakage and injury may result.

1. Allow tool to reach full speed before touching

tool to work surface.

2. Apply minimum pressure to work surface,

allowing tool to operate at high speed. Cutting

rate is greatest when the tool operates at high

speed.

3. Once a cut is begun and a notch is established

in the workpiece, do not change the angle of

the cut. Changing the angle will cause the wheel

to bend and may cause wheel breakage.

4. Remove the tool from work surface before

turning tool off. Allow the tool to stop rotating

before setting it down.

Precautions To Take When Wire

Brushing Paint

1. Wire brushing of lead based paint is NOT

RECOMMENDED due to the difficulty of

controlling the contaminated dust. The greatest

danger of lead poisoning is to children and

pregnant women.

2. Since it is difficult to identify whether or not a

paint contains lead without a chemical analysis,

we recommend the following precautions when

wire brushing any paint:

PERSONAL SAFETY

1. No children or pregnant women should enter

the work area where the paint removal is being

done until all clean up is completed.

2. A dust mask or respirator should be worn by all

persons entering the work area. The filter should

ENGLISH

18

be replaced daily or whenever the wearer has

difficulty breathing.

NOTE: Only those dust masks suitable for

working with lead paint dust and fumes should

be used. Ordinary painting masks do not offer

this protection. See your local hardware dealer

for the proper respiratory protection.

3. NO EATING, DRINKING or SMOKING should

be done in the work area to prevent ingesting

contaminated paint particles. Workers should

wash and clean up BEFORE eating, drinking

or smoking. Articles of food, drink, or smoking

should not be left in the work area where dust

would settle on them.

ENVIRONMENTAL SAFETY

1. Paint should be removed in such a manner as

to minimize the amount of dust generated.

2. Areas where paint removal is occurring should

be sealed with plastic sheeting of 4 mils

thickness.

3. Wire brushing should be done in a manner to

reduce tracking of paint dust outside the work

area.

CLEANING AND DISPOSAL

1. All surfaces in the work area should be

vacuumed and thoroughly cleaned daily for the

duration of the wire brushing project. Vacuum

filter bags should be changed frequently.

2. Plastic drop cloths should be gathered up and

disposed of along with any dust chips or other

removal debris. They should be placed in sealed

refuse receptacles and disposed of through

regular trash pick-up procedures.

During clean up, children and pregnant women

should be kept away from the immediate work

area.

3. All toys, washable furniture and utensils used by

children should be washed thoroughly before

being used again.

Metal Applications

When using the tool in metal applications, make

sure that a residual current device (RCD) has been

inserted to avoid residual risks caused by metal

swarf.

If the power supply is shut off by the RCD, take the

tool to an authorised DeWALT repair agent.

WARNING: In extreme working

conditions, conductive dust can

accumulate inside the machine housing

when working with metal. This can

result in the protective insulation in the

machine becoming degraded with a

potential risk of an electrical shock.

To avoid build-up of metal swarf inside the machine,

we recommend to clear the ventilation slots on a

daily basis. Refer to Maintenance.

MAINTENANCE

Your DeWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

The charger and battery pack are not serviceable.

There are no serviceable parts inside.

Pop-off Brushes

The motor will be automatically shut off indicating

that the carbon brushes are nearly worn out and

that the tool needs servicing. The carbon brushes

are not user-serviceable. Take the tool to an

authorised DeWALT repair agent.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

ページが読み込まれています...

DeWalt DCG412 ユーザーマニュアル

DeWalt DCG412 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント