Sanyo POA-CHL-PL01 Assembly And Installation Manual
- カテゴリー
- プロジェクターマウント
- タイプ
- Assembly And Installation Manual
¡
¡
¡
High-ceiling Bracket
Assembly and
Installation Manual
Model
POA-CHL-PL01
When hanging a projector from the ceiling using this high-ceiling bracket (hereinafter
called "the ceiling bracket"), the ceiling must have adequate strength to support both the
projector and the ceiling bracket. Before installation, check the combined weight of the
projector and ceiling bracket as well as the strength of the ceiling based on that weight.
If the strength is insufficient, provide adequate reinforcement before proceeding.
• Always mount on a level ceiling. Never install on an inclined ceiling.
• During installation, take appropriate measures to prevent lateral swaying due to
earthquakes or vibration (using wires, etc.).
The total weight of the ceiling bracket is 5.2 kg.
Installation
Precautions
Be sure to consult with a qualified
installation specialist.
This high-ceiling bracket is specifically for
use with our projector listed above. Do not
use for any other equipment or purposes.
Be especially careful that children do not
hang from it. Perform proper assembly and
installation by following these Instructions.
Be sure to follow all precautions.
Contents
Installation Precautions .................................. 1
List of Accessories .......................................... 2
Attach the ceiling bracket to the ceiling ........ 2
Attach the projector to the ceiIing bracket .... 3
How to adjust the projection angle ............... 4
■ List of Accessories
■ Attach the ceiiing bracket to the ceiling
After determining the projection distance and ceiling bracket mounting position, attach the ceiling
bracket to the ceiling.
2
Ceiling bracket x 1
High ceiling screws
Phillips head machine screws
(M x 10) x 4
Projection
direction
Off-the-shelf
screws x 8
Ceiling
Projection direction
Pipe for fixing
projector to
ceiling x 1
Projector
Fixing Pipe x 1
Pipe
connecting bolt
Snap pin
Hex nut M6
Flat washer M6
High ceiling screws
(M3 x 10mm)
Philips head
machine screws
Assembly and Installation Manual
(this manual)
Mounting dimensions of pipe for
fixing projector to ceiling
Unit : mm
Detailed connecting view of the projector fixing
pipe and the pipe for fixing projector to ceiling
Snap pin
Hex nut
screw
Pipe
connecting
bolt
Pipe for fixing
projector to
ceiling
Projector
Fixing Pipe
Flat washer
projection direction
* Attach the bracket
so that the arrow is
pointing in the
projection direction
(toward the front of
the projector.)
3
■ Attach the projector to the ceiling bracket
q
Slide the projector bracket attached to the projector over the ceiling bracket attached to the ceiling
as shown in the figure below.
* Be careful not to drop the projector while this process. Although the projector is supported, it
is not secured in place.
* Before attaching the Projector bracket ot the projector, first read each
Projector bracket (sold separately) Assembly and Installation Manual.
w
Use the fastening plates (x2) and the screws (x4) included with the projector bracket (sold
separately) to attach the projector bracket to the ceiling bracket, and be sure to securely tighten the
screws.
To prevent the projector from falling
* To prevent the projector from falling, use the securing wires included with the projector
bracket (sold separately), etc., after carefully reading the Assembly and Installation Manual.
Screw (M6 x 12mm)
Phillips head hex bolt
with integrated spring
washer and flat washer.
Fastening plate
Screw (M3 x 8mm)
Phillips head machine screw with integrated
spring washer.
Screw (M6 x 12mm)
Phillips head hex bolt with integrated
spring washer and flat washer.
Screw (M3 x 8mm)
Phillips head machine screw
with integrated spring washer.
Fastening plate
4
■ Haw to adjust the projection angle
Use the included to loosen the angle adjustment screw, align the projection with the center of the
screen, and then securely tighten the screw.
After securing the projector angle, if
the angle is readjusted without
loosening the screw, the fastening area
could be deformed, which could
prevent it from being tightened again.
When readjusting the angle, Ioosen the
angle adjustment screw before
adjusting the angle.
If the adjustment is off center,
readjust the angle.
Caution
After making the adjustment, be sure the screw is
securely tightened.
[Inclination angle]
[Left/Right angle]
[Vertical angle]
Vertical angle
adjustment
(4 locations)
Inclination angle
adjustment
(4 locations)
Left/Right angle
adjustment
(4 locations)
A length
• Ajust range (20 lengths)
A length
Min
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Sanyo POA-CHL-PL01 Assembly And Installation Manual
- カテゴリー
- プロジェクターマウント
- タイプ
- Assembly And Installation Manual
他の言語で
- English: Sanyo POA-CHL-PL01