LV
-
CL20
©CANON INC. 2011 YT1-6342
2
3
4
5
6
7
8
9
10
Be sure to consult with a qualified
installation specialist.
This ceiling attachment is only for use with CANON
projectors. Do not use for any other equipment or
purposes. Be especially careful that children do not
hang from it. Perform proper assembly and
installation by following these instructions. Be sure
to follow all precautions.
Ceiling Attachment
Assembly and
Installation Manual
Model
LV
-
CL20
Contents
Safety Precautions
----------------------------------------- 2
----------------------------------- 3
Installation Precautions
------------------------------------------------------ 3
Parts List
---- 4
Attach the ceiling attachment to the ceiling
Attach the projector attachment to the projector
---- 5
------- 7
Attach the projector to the ceiling attachment
Attach the drop-prevention wire to the projector
---------- 6
--------------------------------------------------- 9
How to adjust the projection angle
Dimensions
---------------------- 10
Approximate projection distance
--------------------- 8
2
■ Safety Precautions
To Use the Projector Properly
Prohibition
This symbol indicates the other prohibited actions (contents).
Caution
This symbol indicates an action or content that should be taken.
Warning
Make sure the followings when you install and handle the ceiling attachment.
Otherwise, it may result in fire, electric shock or injury.
Caution
Caution
Prohibition
Caution
Make sure the followings when you install and handle the ceiling attachment.
Prohibition
Prohibition
Warning
Caution
●
Make sure to prepare stable scaffolding when installing the ceiling attachment.
● Make sure to fully insert the power plug and connectors when connecting the projector.
Never use a damaged plug or loosen outlet.
●
Make sure to tighten screws for the ceiling attachment securely and never loosen
or remove them.
●
Never look into the lens (projection window) when adjusting the projection because
a high-intensity light is projected from the projector.
●
Never attempt to modify this attachment.
●
Make sure to ask a specialist or sales office if you want to install the ceiling attachment.
An inappropriate installation may cause an accident.
●
During projection, never put an object in front of the projector's lens (projection window).
●
When installing the projector, take appropriate measures using wire or other means to
prevent falling due to an earthquake or other vibration.
Otherwise, the projector may fall, causing injury.
● Be sure to install the ceiling attachment so that there is at least 50 cm between the
projector’s air intake vent and the wall, and at least 1 m between the air exhaust vent
and the wall.
This section indicates information that may cause injury if the
instruction is ignored and the projector is handled inappropriately.
Make sure to abide by the warning to utilize the projector safely.
This section indicates information that may cause injury or death if
the instruction is ignored and the projector is handled inappropriately.
Make sure to abide by the warning to utilize the projector safely.
When hanging a projector from the ceiling using this attachment (hereinafter called
“the ceiling attachment”), the ceiling must have adequate strength to support the
projector, the projector attachment and the ceiling attachment. Before installation,
check the combined weight of the projector, projector attachment and ceiling
attachment as well as the strength of the ceiling based on that weight. If the strength
is insufficient, provide adequate reinforcement before proceeding. Otherwise, the
projector may fall and cause injury.
●When installing the projector, take appropriate measures using wire or other means to prevent falling due to an earthquake
or other vibration. Otherwise, the projector may fall, causing injury.
●Always install to a level ceiling. Never install to an inclined ceiling.
The total weight of the ceiling attachment is 5.9 kg.
■ Installation Precautions
■ Parts List
Projector attachment
......
1
Drop-prevention wires
...
2 Assembly and Installation
Manual (this manual)
Fastening plates
......
2
Screws C
......
4
M6 x 14mm
(Phillips head hex bolt
with integrated spring washer
and flat washer)
Screws A
......
4
M4 x 10mm
(Phillips head machine screw
with integrated spring washer
and flat washer)
Screws D
......
4
M3 x 8mm
(Phillips head machine screw
with integrated spring washer)
Screws B
......
5
M4 x 18mm
(Phillips head machine screw
with integrated spring washer
and flat washer)
3
Ceiling Attachment
.....
1
Wench
.....
1
Caution
4
Turn over the projector and use the included screws B (x5) to attach the Projector attachment.
■ Attach the projector attachment to the projector
Projector attachment
Screws B (included)
...
5
Caution
5
✽Be sure to follow these instructions to keep the
projector from falling. Otherwise, the projector
may fall and cause injury.)
Preventing the projector
from falling:
2. Wind the drop-prevention wire around the
adjuster two more times.
2. Wind the drop-prevention wire around the bar
one more time.
3. Attach the drop-prevention wire to the projector
attachment with the two included screws A, and
then lower the adjuster.
3. Attach the drop-prevention wire to the projector
attachment with the two included screws A.
1. Lift up the adjuster of the projector, and then wind
the included drop-prevention wire around it as
shown in the illustration.
1. Wind the included drop-prevention wire around
the security bar as shown in the illustration.
Installation to the adjusters
q
Installation to the security bar
w
To prevent the projector from falling down, use
the included drop-prevention wire to connect
the projector and the projector attachment.
(2 locations)
■ Attach the drop-prevention wire to the projector
Adjuster
Drop-prevention wire
(included)
Screws A (included)
...
2
Security bar
Screws A (included)
...
2
Drop-prevention wire
(included)
Wind around
two more times.
Wind around
one more time.
Security bar
Adjuster
q
w
(Unit: mm)
Dimensions of Ceiling Attachment
6
Projection direction
Ceiling
4 commercially-available fixing screws
170
196
Hole 2-ø11
2-11mmx14mm slot
120
156
After determining the projection distance and ceiling attachment mounting position,
attach the ceiling attachment to the ceiling.
Refer to P.10 for details on the projection distances.
The fixing screws for ceiling installation are not included.
Use screws which are suitable for the structure of the ceiling.
In addition, do not use screws which are smaller than M10 in size for installation to the ceiling.
■ Attach the ceiling attachment to the ceiling
Caution
Be careful not to drop the projector while this process. As the projector is
supported, but not secured in place, it may fall and cause injury.
Hook the two projections on the ceiling attachment which is installed to the ceiling into
the two slots in the projector attachment which is installed to the projector.
7
w
Use the included Screws C (x4), fastening plates, Screws D (x4) to secure the projector
attachment to the ceiling attachment.
■
Attach the projector to the ceiling attachment
Ceiling Attachment
Projector Attachment
Projection
Slot
Screws D
(included)
...
2
Screws D
(included)
...
2
Screws C
(included)
...
2
Screws C
(included)
...
2
Fastening plates
(included)
Fastening plates
(included)
8
Before adjusting:
• Read the projector instruction manual carefully, turn on the power, and project an image.
• Loosen the slide mechanism fixing screws, and then move the ceiling mount bracket forward or
back to provisionally determine the projection size. Then retighten the slide mechanism fixing
screws and adjust the angle.
Loosen the angle adjustment nut using the wrench included with the ceiling attachment and align the
projector to project the image in the center of the screen. Then fasten the nut securely.
Slides forward
and back
170 mm
■ How to adjust the projection angle
After making the adjustment, be sure the screws are securely
tightened. Otherwise, the projector may fall and cause injury.
Caution
If you try to readjust the projection angle while the screw is still tightened, the attachment may become bent
and it may no longer be possible to tighten it securely again. Always be sure to loosen the angle adjustment
nut before readjusting the projection angle.
Angle adjustment nut
Turns left and right 360°
Slide mechanism
fixing screws
Slide mechanism
fixing screws
15° horizontal tilt
15° horizontal tilt
Wrench
If using a commercially-available
wrench, use one with a size of
24mm.
9
(Unit: mm)
■ Dimensions
77.5
160.5 160.5
209 177
386
352.3
Center of lens
10
Screen size
X(mm) Y(mm)
80”(16:10)
90”(16:10)
100”(16:10)
110”(16:10)
24
69
114
159
439.3
459.3
479.3
499.3
* Height values are intended as a guide only.
The screen sizes may vary depending on the
content of the projected images, so use the
slide mechanism to adjust the position.
Check that the slide mechanism fixing screws are fully tightened even
when not using the sliding mechanism. Otherwise, the projector may
fall and cause injury.
(Unit: mm)
Sliding width
170mm
Y(mm)
233 or more
X(mm)
209 177
386
Slide mechanism fixing screws
■
Approximate projection distance
Caution
/