Not for
Reproduction
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
MILWAUKEE, WISCONSIN, U.S.A.
Copyright © 2016 Briggs & Stratton Power Products Group, LLC
Milwaukee, WI, USA. All rights reserved.
BRIGGS & STRATTON POWER PRODUCTS is a registered
trademark of Briggs & Stratton Corporation
Milwaukee, WI, USA
073042-00
073043-00
073037-00
073038-00
073053-00
en - English
ar -
es - Español
fr - Français
id - Indonesia
ja - 日本語
km - Kmer
ko - 한국말
ms - Melayu
my - Burmese
pt - Português
sw - Kiswahili
th - ไทย
zh - 中文
Manual No. 80006987 Revision D
Product may vary from images shown.
Not for
Reproduction
2 BRIGGSandSTRATTON.COM
2
1
3
A
G
C
B
F
L
N
K
P
R
M
D
H
J
E
Not for
Reproduction
3
5
6
7
8
9
10
11
12
13
14
B
A
TANK
B
A
C
4
Not for
Reproduction
4 BRIGGSandSTRATTON.COM
Important Safety Instructions
SAVE THESE INSTRUCTIONS - This manual
contains important instructions that should be followed
during water pump operation.
Safety and Control Symbols
The safety alert symbol indicates a potential personal
injury hazard. A safety symbol may be used to represent
the type of hazard. WARNING indicates a hazard which,
if not avoided, could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
could result in minor or moderate injury. NOTICE
address practices not related to personal injury.
Original Instructions
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage
fuel tank causing a fire, resulting
in death or serious injury. Contact
with muffler area could cause burns
resulting in serious injury.
• Do not touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 1.5 m (5 ft) of clearance on all sides
of water pump including overhead.
WARNING Fuel and its vapors are extremely
flammable and explosive which
could cause burns, fire or explosion
resulting in death or serious injury.
WHEN ADDING OR DRAINING FUEL
• Turn water pump OFF and let it cool at least 2
minutes before removing fuel cap. Loosen cap
slowly to relieve pressure in tank.
• Fill or drain fuel tank outdoors.
• DO NOT overfill tank. Allow space for fuel expansion.
• If fuel spills, wait until it evaporates before
starting engine.
• Keep fuel away from sparks, open flames, pilot
lights, heat, and other ignition sources.
• DO NOT light a cigarette or smoke.
WHEN STARTING EQUIPMENT
• DO NOT start unless spark plug, muffler, fuel cap,
and air cleaner are in place.
• DO NOT crank engine with spark plug removed.
WHEN OPERATING EQUIPMENT
• DO NOT pump flammable liquids, such as fuel or
fuel oils.
• This water pump is not for use in mobile equipment
or marine applications.
• DO NOT tip engine or equipment at angle which
causes fuel to spill.
• Secure water pump. Loads from hoses may
cause tipover.
• DO NOT stop engine by moving choke control to
CHOKE position ( ).
WHEN TRANSPORTING OR REPAIRING EQUIPMENT
• Transport/repair with fuel tank EMPTY or with fuel
shutoff valve OFF.
• Disconnect spark plug wire.
WHEN STORING FUEL OR EQUIPMENT WITH
FUEL IN TANK
• Store away from furnaces, stoves, water heaters,
clothes dryers, or other appliances that have pilot
light or other ignition source because they can
ignite fuel vapors.
Table of Contents
Important Safety Instructions .................... 4
Equipment Description......................... 6
Features & Controls ........................... 6
Assembly.................................... 6
Operation.................................... 7
Maintenance ................................. 9
Storage ..................................... 9
Troubleshooting .............................10
Product Specifications ........................10
Warranty ...................................11
Fire
Explosion
Toxic Fumes
Hot Surface
Safety Alert
Symbol
Instruction Manual
Oil Level
On
Off
Fuel
Engine Control
!
Do Not Start
Engine
Choke
Run
Suffication
Suffication
Oil
Kickback
Slippery Surface
Moving Parts
Slow Fast
Not for
Reproduction
5
WARNING Use of water pump could create
puddles and slippery surfaces causing you
to fall resulting in death or serious injury.
• Operate water pump from a stable surface.
• The area should have adequate slopes and
drainage to reduce the possibility of a fall due to
slippery surfaces.
WARNING Starter cord kickback (rapid retraction)
will pull hand and arm toward engine faster
than you can let go which could cause
broken bones, fractures, bruises, or sprains
resulting in serious injury.
• When starting engine, pull cord slowly until resistance
is felt and then pull rapidly to avoid kickback.
• Keep hands and body clear from discharge of pump.
• Secure discharge hose to avoid whipping.
WARNING Starter and other rotating parts could
entangle hands, hair, clothing, or accessories
resulting in serious injury.
• NEVER place hands or body parts inside of running
pump or hoses.
• NEVER operate water pump without protective
housing or covers.
• DO NOT wear loose clothing, jewelry or anything that
may be caught in the starter or other rotating parts.
• Tie up long hair and remove jewelry.
NOTICE This water pump is manufactured to
pump ONLY water that is not intended for human
consumption.
NOTICE Improper treatment of water pump could
damage it and shorten its life.
• If you have questions about intended use, ask
dealer or contact qualified service center.
• Be sure pump chamber is filled with water before
starting the engine. Never run pump without priming.
• Use a non-collapsible hose on the suction side of pump.
• Use water pump only for intended uses.
• Pumping sea water, beverages, acids, chemical
solutions, or any other liquid that promotes
corrosion can damage the pump.
• Ensure all connections are air tight.
• DO NOT obstruct suction or discharge hose in
any way.
• NEVER operate pump without strainer basket
connected to end of suction hose.
• DO NOT exceed suction head maximum (see
Specifications). Use shortest suction head possible.
• NEVER allow vehicles to drive over hoses. If a hose
must be positioned across a roadway, use planking
on each side of hose to allow vehicles to pass over
without obstructing or collapsing hose.
• Anchor pump to avoid “walking” or equipment
movement, especially if located near a ditch or edge
of open ravine. The equipment could fall in.
• Keep equipment away from edge of river or lake
where it could cause the bank to collapse.
• DO NOT insert any objects through cooling slots.
• NEVER operate units with broken or missing parts,
or without protective housing or covers.
• DO NOT by-pass any safety device on this machine.
• NEVER move machine by pulling on hoses - use frame
on unit.
• DO NOT allow unqualified persons or children to
operate or service water pump.
• Check fuel system for leaks or signs of deterioration,
such as chafed or spongy hose, loose or missing
clamps, or damaged tank or cap. Correct all defects
before operating water pump.
• This equipment is designed to be used with Briggs
& Stratton Power Products authorized parts only. If
equipment is used with parts that DO NOT comply
with minimum specifications, user assumes all risks
and liabilities.
WARNING POISONOUS GAS HAZARD.
Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes.
You CANNOT see it, smell it, or taste it. Even
if you do not smell exhaust fumes, you could
still be exposed to carbon monoxide gas. If you start
to feel sick, dizzy or weak while using this product,
get to fresh air RIGHT AWAY. See a doctor. You
may have carbon monoxide poisoning.
• Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of
carbon monoxide gas from accumulating and
potentially being drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-
up according to the manufacturer’s instructions.
Smoke alarms cannot detect carbon monoxide gas.
• DO NOT run this product inside homes, garages,
basements, crawls paces, sheds, or other partially-
enclosed spaces even if using fans or opening
doors and windows for ventilation. Carbon monoxide
can quickly build up in these spaces and can linger
for hours, even after the product has shut off.
• ALWAYS place this product downwind and point
the engine exhaust away from occupied spaces.
Not for
Reproduction
6 BRIGGSandSTRATTON.COM
Equipment Description
Read this manual carefully and become
familiar with your water pump. Know its
applications, its limitations, and any
hazards involved. Save these instructions
for future reference.
This machine is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge.
Every effort has been made to ensure that information
in this manual is accurate and current. However, the
manufacturer reserves the right to change, alter, or
otherwise improve the water pump and this document at
any time without prior notice.
NOTICE If you have questions about intended use,
contact an authorized service dealer. This equipment
is designed to be used with Briggs & Stratton Power
Products authorized parts ONLY.
Features and Controls Figure
Assembly
Oil
Oil Recommendations Figure
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF,
SG, SH, SJ or higher. DO NOT use special additives.
Outdoor temperatures determine the proper oil
viscosity for the engine. Use the chart to select the best
viscosity for the outdoor temperature range expected.
Checking Oil Level Figure
Oil level should be checked prior to each use or at least
every 8 hours of operation. Keep oil level maintained.
1. Make sure water pump is on a level surface.
2. Clean area around oil fill and remove oil fuel cap
(A).
3. Verify oil is at the point of overflowing (B).
4. Replace and tighten oil cap.
1
2
Adding Engine Oil
1. Make sure water pump is on a level surface.
2. Check oil level as described in Checking Oil Level.
3. If needed, slowly pour oil into oil fill opening to the
point of overflowing at oil fill.
4. Replace and tighten oil fill cap.
Add Fuel Figure
Fuel must meet these requirements:
• Clean, fresh, unleaded petrol.
• A minimum of 87 octane/87 AKI (91 RON). For
high altitude use, see High Altitude.
• Petrol with up to 10% ethanol (gasohol) is
acceptable.
NOTICE Use of unapproved fuels will damage the
engine components and void the engine warranty.
• DO NOT use unapproved petrol, such as E15 and
E85.
• DO NOT mix oil in petrol or modify the engine to
run on alternate fuels.
To protect the fuel system from gum formation, mix
in a fuel stabilizer when adding fuel. See Storage.
All fuel is not the same. If you experience starting or
performance problems after using fuel, switch to a
different fuel provider or change brands. This engine is
certified to operate on gasoline. The emission control
system for this engine is EM (Engine Modifications).
1. Make sure water pump is on a level surface.
2. Clean area around fuel fill cap and remove cap.
3. Slowly add unleaded fuel (A) to fuel tank (B). Be
careful not to fill above the baffle (C). This allows
adequate space for fuel expansion as shown.
4. Install fuel cap and let any spilled fuel evaporate
before starting engine.
4
WARNING Fuel and its vapors are extremely
flammable and explosive which
could cause burns, fire or explosion
resulting in death or serious injury .
WHEN ADDING FUEL
• Turn water pump OFF and let it cool at least 2
minutes before removing fuel cap. Loosen cap
slowly to relieve pressure in tank.
• Fill or drain fuel tank outdoors.
• DO NOT overfill tank. Allow space for fuel expansion.
• If fuel spills, wait until it evaporates before
starting engine.
• Keep fuel away from sparks, open flames, pilot
lights, heat, and other ignition sources.
• Check fuel lines, tank, cap and fittings frequently for
cracks or leaks. Replace if necessary.
• DO NOT light a cigarette or smoke.
3
A Priming Plug J Water Drain Plug
B Air Cleaning K ID Label
C Spark Plug L Suction Inlet
D Engine Controls M Discharge Outlet
E Choke Lever N Recoil Starter
F Oil Fill Cap P On/Off Switch
G Fuel Valve R Engine Information Label
H Oil Drain Plug S Fuel Tank
Not for
Reproduction
7
High Altitude
At altitudes over 1524 meters (5,000 feet), a minimum
85 octane / 85 AKI (89 RON) gasoline is acceptable. To
remain emissions compliant, high altitude adjustment is
required. Operation without this adjustment will cause
decreased performance, increased fuel consumption,
and increased emissions. See an Authorized Briggs &
Stratton dealer for high altitude adjustment information.
Operation of the engine at altitudes below 762 meters
(2,500 feet) with the high altitude kit is not recommended.
Assemble and Attach Hoses
You will need the following tool to install the hoses to the
water pump:
• 10 mm nut driver
Connect Suction Hose to Pump
Use a commercially available hose. The suction hose
must be reinforced with a non-collapsible wall or
braided material. DO NOT use a hose with an inside
diameter smaller than the pumps suction port size.
1.
Slide barb cuff over hose barb. Insert rubber seal
into end of barb cuff.
Figure
2.
Screw hose barb assembly onto pump in clockwise
rotation until hose barb assembly is tightened
securely.
Figure
3.
Slide hose clamp over end of hose. Slide suction
hose onto hose barb. Tighten hose clamp securely
using a standard 10 mm nut driver.
Figure
Attach Suction Hose to Strainer Basket Figure
Slide hose clamp over hose. Attach open end of
suction hose to strainer hose barb. Tighten hose clamp
securely using a standard 10 mm nut driver.
Connect Discharge Hose (Optional)
If desired, use a commercially available hose. DO NOT
use a hose with an inside diameter smaller than the
pump’s discharge port size.
1. Slide barb cuff over hose barb. Insert rubber seal
into end of barb cuff.
2. Screw hose barb assembly onto pump in clockwise
rotation until hose barb assembly is tightened
securely. Figure
3. Slide hose clamp over end of discharge hose.
Slide discharge hose onto hose barb. Tighten
hose clamp securely using a standard 10 mm nut
driver. Figure
7
5
6
8
9
10
Operation
Water Pump Location Figure
For best pump performance, locate the pump on a
flat, level surface as close as possible to the water to
be pumped. Secure water pump to avoid tipover. Use
hoses that are no longer than necessary.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage fuel tank
causing a fire, resulting in death or serious
injury.
• Keep at least 1.5 m (5 ft) of clearance on all sides
of water pump including overhead.
Carbon Monoxide Poisoning
WARNING POISONOUS GAS HAZARD. Engine
exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes.
You CANNOT see it, smell it, or taste it. Even
if you do not smell exhaust fumes, you could still be
exposed to carbon monoxide gas. If you start to feel
sick, dizzy or weak while using this product, get to
fresh air RIGHT AWAY. See a doctor. You may have
carbon monoxide poisoning.
• Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of
carbon monoxide gas from accumulating and
potentially being drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-
up according to the manufacturer’s instructions.
Smoke alarms cannot detect carbon monoxide gas.
• DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors
and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for
hours, even after the product has shut off.
• ALWAYS place this product downwind and point
the engine exhaust away from occupied spaces.
What is “Head”? Figure
Head refers to the height of a column of water that can
be delivered by the discharge of the pump.
Suction Head (A) is the vertical distance between the
center of the pump and the surface of the liquid on the
suction side of the pump. May also be referred to as
“suction lift”. The atmospheric pressure of 1 bar (14.5
psi) at sea level limits suction head lift to less than
approximately 8m (26 ft) for any pump.
Discharge Head (B) is the vertical distance between
the pump’s discharge port and the point of discharge,
which is the liquid surface if the hose is submerged or
pumping into the bottom of a tank.
11
14
Not for
Reproduction
8 BRIGGSandSTRATTON.COM
As water pumping height increases, pump output
decreases. The length, type, and size of the suction
and discharge hoses can also significantly affect pump
output.
It is important for the suction operation to be the
shorter part of the total pumping action. This will
decrease the priming time and improve pump
performance by increasing the discharge head.
See Specifications for maximum head values.
Prime the Water Pump Figure
1. Remove priming plug from top of pump.
2. Fill pump with clean water up to level shown.
3. Replace priming plug.
NOTICE Improper treatment of water pump can
damage it and shorten its life.
• Be sure pump chamber is filled with water before
starting the engine. Never run pump without priming.
Locate Strainer Basket Into Water Source
Figure
Place strainer basket into water to be pumped. Basket
must be fully immersed in water. To reduce sand or silt
suction, place basket into bucket or on top of coarse rocks.
NOTICE Improper treatment of water pump can
damage it and shorten its life.
• NEVER operate pump without strainer basket
connected to end of suction hose.
• Keep strainer out of sand or silt - place in bucket or
on stones.
• DO NOT let pump run dry or damage to seals may
result. Never run pump without priming.
• DO NOT pump salt water.
Starting the Water Pump Figure
Use the following start instructions:
1. Make sure unit is on a flat, level surface and pump
chamber is primed.
2. Move fuel shutoff (G) to ON (I) position.
3. Move choke lever (E) to CHOKE ( ) position.
4. Turn on/off switch (P) to ON (I) position.
5. Move engine speed lever (D) to FAST ( ) position.
WARNING Starter cord kickback (rapid retraction)
will pull hand and arm toward engine faster
than you can let go which could cause
broken bones, fractures, bruises, or sprains
resulting in serious injury.
• When starting engine, pull cord slowly until resistance
is felt and then pull rapidly to avoid kickback.
• Keep hands and body clear from discharge of pump.
• Secure discharge hose to avoid whipping.
6.
Grasp recoil handle (N) and pull slowly until
slight resistance is felt. Then pull handle rapidly
to overcome compression, prevent kickback and
start engine.
NOTICE
If excessive fuel is present in the air/fuel
mixture causing a “flooded” condition, engine won’t
start. Move choke lever (E) to RUN ( ) position and
pull handle repeatedly until engine starts.
7.
As the engine warms, move choke lever (E) to
RUN ( ) position. Operate with choke in RUN
position.
NOTICE
It may take a few minutes for water pump to
begin pumping water.
NOTICE
If engine starts after 3 pulls but fails to run, or if
unit shuts down during operation, make sure unit is on a
level surface and check for proper oil level in crankcase.
This unit is equipped with a low oil protection device. If
so, oil must be at proper level for engine to start.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage
fuel tank causing a fire, resulting
in death or serious injury. Contact
with muffler area could cause burns
resulting in serious injury.
• Do not touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 1.5 m (5 feet) of clearance on all sides
of water pump including overhead.
Pump output is controlled by adjusting engine speed.
Moving the engine speed lever in the FAST ( )
direction will increase pump output, and moving the
engine speed lever in the SLOW ( ) direction will
decrease pump output.
Stopping the Water Pump Figure
1.
Move engine speed lever (D) to SLOW ( ) position.
WARNING Fuel and its vapors are extremely
flammable and explosive which
could cause burns, fire or explosion
resulting in death or serious injury.
• DO NOT stop engine by moving choke lever to
CHOKE position ( ).
2. Turn on/off switch (P) to OFF (0) position.
3. Move fuel shutoff (G) to OFF (0) position.
Drain and Flush Water Pump Figure
1. Disconnect and drain suction and discharge hoses.
2. Remove drain plug (J) at bottom of pump.
3. Remove primer plug (A) from top of pump and
flush internal components of pump with clean
water.
4. Replace both plugs and finger tighten.
13
12
1
1
1
Not for
Reproduction
Maintenance
Maintenance Schedule
Follow the hourly or calendar intervals, whichever
occurs first. More frequent service is required when
operating in adverse conditions noted below.
First 5 hours
Change oil
Every 8 hours or daily
Check oil level
Clean debris
Every 25 hours or daily
Clean engine air filter
Clean pre-cleaner, if equipped
Every 50 hours or annually *
Change oil *
Clean and inspect spark arrester
Annually
Replace spark plug
Replace air filter *
Clean air cooling system *
Clean any sludge buildup inside pump
*Service sooner when operating under dirty or dusty conditions.
General Recommendations
Regular maintenance will improve performance and
extend the life of the water pump. See any Briggs &
Stratton Authorized Service Dealer for service.
Installation and major repair work should only be
performed by specifically trained personnel.
The water pump’s warranty does not cover items that
have been subjected to operator abuse or negligence.
To receive full value from the warranty, the operator must
maintain the water pump as instructed in this manual.
WARNING To ensure machine safety, use only
original spare parts from the manufacturer or approved
by the manufacturer. Should you have questions about
replacing components on your water pump, please visit
our website at BRIGGSandSTRATTON.COM.
Storage
If storing the unit for more than 30 days, use the
following guidelines to prepare it for storage.
Protect Fuel System
Fuel can become stale when stored over 30 days.
Stale fuel causes acid and gum deposits to form in the
fuel system or on essential carburetor parts.
There is no need to drain gasoline from the engine
if a fuel stabilizer is added according to instructions.
Run the engine outdoors for 2 minutes to circulate the
stabilizer throughout the fuel system before storage.
If gasoline in the engine has not been treated with a fuel
stabilizer, it must be drained into an approved container.
Run the engine outdoors until it stops from lack of fuel.
The use of a fuel stabilizer in the storage container is
recommended to maintain freshness.
WARNING Fuel and its vapors are extremely
flammable and explosive which
could cause burns, fire or explosion
resulting in death or serious injury.
WHEN STORING FUEL OR EQUIPMENT WITH
FUEL IN TANK
• Store away from furnaces, stoves, water heaters,
clothes dryers, or other appliances that have pilot
light or other ignition source because they can
ignite fuel vapors.
WHEN DRAINING FUEL
• Turn water pump OFF and let it cool at least 2
minutes before removing fuel cap. Loosen cap
slowly to relieve pressure in tank.
• Drain fuel tank outdoors.
• Keep fuel away from sparks, open flames, pilot
lights, heat, and other ignition sources.
• DO NOT light a cigarette or smoke.
Other Storage Tips
1. DO NOT store fuel from one season to another
unless it has been treated as described in Protect
Fuel System.
2. Store water pump in clean, dry area and cover
with a suitable protective cover that does not
retain moisture.
WARNING Storage covers could cause a fire
resulting in death or serious injury.
• DO NOT place a storage cover over a hot water pump.
• Let equipment cool for a sufficient time before
placing the cover on the equipment.
9
Not for
Reproduction
10 BRIGGSandSTRATTON.COM
Troubleshooting
Power Ratings: The gross power rating for individual petrol engine models is labeled in accordance with SAE (Society of Automotive Engineers)
code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque values are derived at 2600
RPM for those engines with “rpm” called out on the label and 3060 RPM for all others; horsepower values are derived at 3600 RPM. The gross
power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with exhaust and air cleaner installed whereas
gross power values are collected without these attachments. Actual gross engine power will be higher than net engine power and is affected by,
among other things, ambient operating conditions and engine-to-engine variability. Given the wide array of products on which engines are placed,
the petrol engine may not develop the rated gross power when used in a given piece of power equipment. This difference is due to a variety
of factors including, but not limited to, the variety of engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.),
application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to engine variability. Due to manufacturing and
capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this engine.
* This water pump is rated in accordance with Briggs & Stratton standard 621K.
Problem Cause Correction
running
1. Pump not primed.
2.
Suction or discharge hose restricted,
collapsed, damaged, too long, or diameter
too small.
3. Strainer not completely under water.
4. Air leak at suction hose connector.
5. Strainer clogged.
6. Excessive or marginal head.
7. Engine speed lever is in SLOW position.
1. Fill pump chamber with water and prime pump.
2. Replace suction or discharge hose.
3. Sink the strainer and the end of suction
hose completely under water.
4
.
Replace sealing washer if missing or
damaged. Tighten hose connector and clamp.
5. Clean debris from strainer.
6.
Relocate pump and/or hoses to reduce head.
7.
Move engine speed lever to FAST position.
1. Rocker switch set to OFF (0).
2. Fuel shutoff is in OFF (0) position.
3. Dirty air cleaner.
4. Out of fuel.
5. Stale or contaminated fuel or water in
fuel.
6
. Spark plug wire not connected to spark plug.
7. Bad spark plug.
8. Excessive fuel is present in the air/fuel
mixture causing a “flooded” condition.
9. Carburetor is out of adjustment.
1. Set switch to ON (I).
2. Turn fuel shutoff to ON (I) position.
3. Clean or replace air cleaner.
4. Wait two minutes and fill fuel tank.
5. Drain fuel tank and carburetor; fill with fresh
fuel.
6. Connect wire to spark plug.
7. Replace spark plug.
8. Wait 5 minutes and re-crank engine.
9. Contact Authorized service facility.
Engine
shuts down
when running.
Out of fuel. Wait two minutes and fill fuel tank.
Specifications
Model 073043
Suction & Discharge Port Diameter...........50 mm (2 in)
Maximum Discharge Capacity * . 500 l/min (130 US gal/min)
Displacement ........................163 cc (9.95 in
3
)
Model 073042
Suction & Discharge Port Diameter...........76 mm (3 in)
Maximum Discharge Capacity * . 900 l/min (240 US gal/min)
Displacement .......................208 cc (12.69 in
3
)
Model 073037 & 073053
Suction & Discharge Port Diameter...........50 mm (2 in)
Maximum Discharge Capacity * . 450 l/min (120 US gal/min)
Displacement ........................127 cc (7.74 in
3
)
Model 073038
Suction & Discharge Port Diameter...........76 mm (3 in)
Maximum Discharge Capacity * . 900 l/min (240 US gal/min)
Displacement ........................163 cc (9.95 in
3
)
Common Specifications
Maximum Suction Head * ....................8 m (26 ft)
Maxium Discharge Head * ...................25 m (82 ft)
Oil Capacity............................. 0.59 l (20 oz)
Common Service Parts
Air Filter (127CC) .............................796970
Air Filter, Oval (163 & 208CC)...................590601
Air Filter Pre-cleaner, Oval (163 & 208CC) ........590602
Fuel Additive ..........................100117, 100120
Resistor Spark Plug (127CC) ...................797235
Resistor Spark Plug (163 & 208CC) ..............491055
Not for
Reproduction
11
BRIGGS & STRATTON PRODUCTS WARRANTY POLICY January 2014
LIMITED WARRANTY
Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or
workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is
effective for and is subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator
map at www.briggsandstratton.com. The purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized Service
Dealer for inspection and testing.
There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to
the warranty period listed below, or to the extent permitted by law. Liability for incidental or consequential damages are excluded to the extent
exclusion is permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you
specific legal rights and you may also have other rights which vary from state to state or country to country.**
WARRANTY PERIOD
Item
Equipment 12 months
Engine* 12 months
Battery (if equipped) 12 months
* Applies to Briggs & Stratton engines only. Warranty coverage of non-Briggs & Stratton engines is provided by that engine manufacturer. Emissions-related
components are covered by the Emissions Warranty Statement.
** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer
locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton
Australia Pty Ltd, 1 Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a
retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced
commercial use, it shall thereafter be considered as a commercial use product for purposes of this warranty.
To ensure prompt and complete warranty coverage, register your product at the website shown above or at www.onlineproductregistration.com, or mail the
complete registration card (if provided), or call 1-800-743-4115 (in USA).
Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the
product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.
ABOUT YOUR WARRANTY
Warranty service is available only through Authorized Service Dealers. Most warranty repairs are handled routinely, but sometimes requests for warranty service
may not be appropriate. This warranty covers only defects in materials or workmanship. It does not cover damage caused by improper use or abuse, improper
maintenance or repair, normal wear and tear, or stale or unapproved fuel.
Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the
Operator’s Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial
number on the product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage
or water/chemical corrosion damage.
Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced
or repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.
Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when
normal use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine
brake pads) are not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.
Stale or Unapproved Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine or
equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.
Other Exclusions - This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration.
Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for
primary power in place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or
demonstration equipment or engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.
80009359 EN, Rev -
Not for
Reproduction
5
•
•
•
•
•
•
•
•
•
ةظحم
ةظحم
•
.Briggs & Stratton
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Briggs & Stratton
Not for
Reproduction
ةظحم
•
•
•51.5
•
•
•
•
•
•
•
•
•
•
•
•
•
.(
•
•
•
4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 . . . . . . . . . . . . . . . . . . . . . . . . . .
10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
!
BRIGGSandSTRATTON.COM 4
Not for
Reproduction
7
BA 3
C
4
5,000
1524
AKI (89 RON 8585
Briggs & Stratton
762
2,500)
10
1
2
3
6
1/4)
6
1/4)
1
2
3
1/46
7
5
6
8
9
10
•51.5
A)
14.51
8
26)
B)
14
11
Not for
Reproduction
ةظحم
. Briggs & Stratton
AJ
BK
CL
DM
EN
FP
GR
HS
Briggs & Stratton
SHSGSF
SJ
3
8
1
.(A 2
.(B 3
4
1
1
2
.3
4
AKI þ(91 RON 8787
.
10
.E85E15
EM
1
2
4
•
•
•
•
•
•
•
BRIGGSandSTRATTON.COM 6
2
Not for
Reproduction
9
5
8
25
50
Briggs & Stratton
.BRIGGSandSTRATTON.COM
30
30
•
•
•
•
•
1
2
•
•
Not for
Reproduction
1
2
3
ةظحم
•
ةظحم
•
•
•
•
1
.(IG 2
.( E 3
.(IP .4
.( D 5
•
•
•
N 6
ةظحم
(E
7
)
ةظحم
3 ةظحم
•
•
•51.5
)
.( D 1
.(
.(0P 2
.(0G 3
1
J 2
A 3
4
12
13
1
1
1
BRIGGSandSTRATTON.COM 8
Not for
Reproduction
11
2014
12
12
12
(
)
”
“
”
“
Not for
Reproduction
J1940SAE
30602600SAE J1995
www.BRIGGSandSTRATTON.COM3600
Briggs & Stratton
.621K
*
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
.(0
.(02
3
4
5
6
7
8
9
. (I1
.(I2
3
4
5
6
7
51 .8
9
BRIGGSandSTRATTON.COM
10
073043
250 . . . . . . . . . . . . . . . . . . . . . . . . . . .
130500 . . . . . .*
(
3
9.95163 . . . . . . . . . . . . . . . . . . . . . . . . . . .
073042
376 . . . . . . . . . . . . . . . . . . . . . . . . . . .
240900 . . . . . .*
(
3
12.69208 . . . . . . . . . . . . . . . . . . . . . . . . . .
073053 & 073037
250 . . . . . . . . . . . . . . . . . . . . . . . . . . .
120450 . . . . . .*
(
3
7.74127 . . . . . . . . . . . . . . . . . . . . . . . . . . .
073038
376 . . . . . . . . . . . . . . . . . . . . . . . . . . .
240900 . . . . . .*
(
3
9.95163 . . . . . . . . . . . . . . . . . . . . . . . . . . .
268. . . . . . . . . . . . . . . . . . . . . . *
82
25 . . . . . . . . . . . . . . . . . . . .*
200.59. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
796970 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (127CC
590601 . . . . . . . . . . . . . . . . . . (208CC & 163
590602 . . . . . . . . . . . . . . . . . . (208CC & 163
100120100117 . . . . . . . . . . . . . . . . . . . . . . . . . . .
797235 . . . . . . . . . . . . . . . . . . . . . . . . (127CC
491055 . . . . . . . . . . . . . . . . . . (208CC & 163
Not for
Reproduction
4 BRIGGSandSTRATTON.COM
Instrucciones de seguridad
importantes
CONSERVE ESTAS INSTRUCCIONES - Este manual
contiene instrucciones importantes que se deben
seguir durante el funcionamiento de la bomba de agua.
Símbolos de seguridad y control
El símbolo de alerta de seguridad indica un posible
riesgo para su integridad física. Se puede usar un
símbolo de seguridad para representar el tipo de riesgo.
ADVERTENCIA indica un peligro que si no es evitado,
podría ocasionar la muerte o heridas graves. PRECAUCIÓN
indica un peligro, que si no es evitado, podría ocasionar
lesiones leves o moderadas. AVISO hace referencia a una
práctica no relacionada con una lesión física.
ADVERTENCIA Los gases y el calor de escape pueden
inflamar los materiales combustibles
y las estructuras o dañar el tanque de
combustible y provocar un incendio, lo
que podría causar la muerte o lesiones
graves. El contacto con el área del silenciador puede
causar quemaduras que podrían causar la muerte o
lesiones graves.
• No toque las piezas calientes y EVITE los gases
calientes del escape.
• Deje que el equipo se enfríe antes de tocarlo.
• Deje un espacio mínimo de 1.5 m (5 pies) alrededor de la
bomba de agua, incluida la parte superior.
ADVERTENCIA El combustible y sus vapores son
extremadamente inflamables y explosivos,
lo que podría causar quemaduras,
incendios o explosiones que conlleven la
muerte o lesiones graves.
CUANDO AÑADA COMBUSTIBLE O VACÍE EL DEPÓSITO
• APAGUE la bomba de agua y déjela enfriar al menos por
2 minutos antes de quitar la tapa de combustible. Afloje
lentamente la tapa para eliminar la presión del tanque.
• Llene o vacíe el tanque de combustible a la intemperie.
• NO llene el depósito en exceso. Deje espacio en el
tanque para permitir la expansión del combustible.
• Si se ha derramado combustible, espere a que se
evapore antes de arrancar el motor.
• Mantenga el combustible alejado de chispas, llamas
abiertas, pilotos, fuentes de calor y otras fuentes de ignición.
• NO encienda cigarrillos ni fume.
CUANDO PONGA EN FUNCIONAMIENTO EL EQUIPO
• NO arranque a menos que la bujía, el silenciador, el
tapón del depósito de combustible y el filtro de aire estén
instalados.
• NO arranque el motor sin la bujía instalada.
CUANDO UTILICE EL EQUIPO
• NO bombee líquidos inflamables, como combustibles o
aceites.
• Esta bomba de agua no se puede utilizar en equipos
móviles o en aplicaciones marítimas.
• NO incline el motor ni el equipo de forma que pueda
derramarse el combustible.
• Asegure la bomba de agua. Las cargas de las mangueras
pueden provocar la caída de la bomba.
• NO coloque el estrangulador en la posición CEBADO (
) para parar el motor.
CUANDO TRANSPORTE O REPARE EL EQUIPO
• Transporte o repare el equipo con el depósito de
combustible VACÍO o con la válvula de paso de
combustible CERRADA.
• Desconecte el cable de la bujía.
CUANDO GUARDE COMBUSTIBLE O EL EQUIPO CON
COMBUSTIBLE EN EL DEPÓSITO
• Manténgalo alejado de calderas, estufas, calentadores
de agua, secadoras de ropa y otros aparatos que
utilicen pilotos luminosos u otras fuentes de ignición que
pudieran inflamar los vapores de combustible.
Índice
Instrucciones de seguridad importantes........... 4
Descripción del equipo......................... 6
Características y controles...................... 6
Armado ..................................... 6
Operación ................................... 7
Mantenimiento ............................... 9
Almacenamiento.............................. 9
Solución de problemas........................10
Especificaciones del producto..................10
Garantía....................................11
Incendio
Explosión
Gases Tóxicos
Superficie
caliente
Símbolo de alerta
de seguridad
Manual de
instrucciones
Nivel de aceite
Encendido
Apagado
Combustible
Control del
motor
!
No arrancar el
motor
Cebado
En
funcionamiento
Asfixia
Asfixia
Aceite
Retroceso
Superficie
resbaladiza
Piezas
móviles
Lento
Rápido
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
Simplicity 073038-00 ユーザーマニュアル
- タイプ
- ユーザーマニュアル
関連論文
-
Simplicity WATER PUMP, BRIGGS & STRATTON MODEL 073051-00,073052-00 ユーザーマニュアル
-
-
-
-
-
Simplicity 2691269-00 ユーザーマニュアル
-
-
-