Hilti SFD 2-A 取扱説明書

SFD 2-A

English 1

Français 15

Dansk 31

Svenska 45

Norsk 59

Suomi 73

Eesti 87

Latviešu 101

Lietuvių 116

Русский 131

Українська 149

Қазақ 167

Türkçe 184

ﻋﺮﺑﻲ 198

日本語 213

한국어 227

繁體中文 240

中文 252

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

1

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

2

3

4

5

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

SFD 2-A

en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 1

fr Notice d'utilisation originale . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

da Original brugsanvisning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

sv Originalbruksanvisning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

no Original bruksanvisning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

fi Alkuperäiset ohjeet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

et Originaalkasutusjuhend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

lv Oriģinālā lietošanas instrukcija . . . . . . . . . . . . . . . . . . . . . . . . 101

lt Originali naudojimo instrukcija . . . . . . . . . . . . . . . . . . . . . . . . 116

ru Перевод оригинального руководства по

эксплуатации . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

uk Оригінальна інструкція з експлуатації . . . . . . . . . . . . . . . . . 149

kk Түпнұсқа пайдалану бойынша нұсқаулық . . . . . . . . . . . . . 167

tr Orijinal kullanım kılavuzu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184

ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198

ja オリジナル取扱説明書 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213

ko 오리지널 사용 설명서 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227

zh 原始操作說明 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240

cn 原版操作说明 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

*2248872*

2248872 English 1

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a

prerequisite for safe, trouble-free handling and use of the product.

• Observe the safety instructions and warnings in this documentation and

on the product.

• Always keep the operating instructions with the product and make sure

that the operating instructions are with the product when it is given to

other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the

product. The following signal words are used:

DANGER

DANGER !

▶ Draws attention to imminent danger that will lead to serious personal

injury or fatality.

WARNING

WARNING !

▶ Draws attention to a potential threat of danger that can lead to serious

injury or fatality.

CAUTION

CAUTION !

▶ Draws attention to a potentially dangerous situation that could lead to

slight personal injury or damage to the equipment or other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use.

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household

waste

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

2 English 2248872

*2248872*

These numbers refer to the corresponding illustrations found at the

beginning of these operating instructions

The numbering reflects the sequence of operations shown in the

illustrations and may deviate from the steps described in the text

Item reference numbers are used in the overview illustrations and

refer to the numbers used in the product overview section

This symbol is intended to draw special attention to certain points

when handling the product.

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols are used on the product:

Drilling without hammer action

Revolutions per minute

Rated speed under no load

Direct current (DC)

Li-ion battery

Hilti Li-ion battery type series used. Observe the information given in

the section headed Intended use.

The product supports wireless data transmission compatible with

iOS and Android platforms.

1.4 Product information

products are designed for professional users and only trained,

authorized personnel are permitted to operate, service and maintain the

products. This personnel must be specifically informed about the possible

hazards. The product and its ancillary equipment can present hazards if

used incorrectly by untrained personnel or if used not in accordance with

the intended use.

The type designation and serial number are printed on the rating plate.

▶ Write down the serial number in the table below. You will be required to

state the product details when contacting Hilti Service or your local Hilti

organization to inquire about the product.

Product information

Drill/driver SFD 2-A

Generation: 01

Serial no.:

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

*2248872*

2248872 English 3

1.5 Declaration of conformity

We declare, on our sole responsibility, that the product described here

complies with the applicable directives and standards. A copy of the

declaration of conformity can be found at the end of this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916

Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and

specifications provided with this power tool. Failure to follow all instruc-

tions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

Work area safety

▶ Keep work area clean and well lit. Cluttered or dark areas invite

accidents.

▶ Do not operate power tools in explosive atmospheres, such as in

the presence of flammable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

▶ Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

Electrical safety

▶ Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will reduce risk of electric

shock.

▶ Avoid body contact with earthed or grounded surfaces, such as

pipes, radiators, ranges and refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

▶ Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

▶ Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled cords increase the risk

of electric shock.

▶ Whenoperatingapowertooloutdoors, use anextension cord suitable

for outdoor use. Use of a cord suitable for outdoor use reduces the risk

of electric shock.

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

4 English 2248872

*2248872*

▶ If operating a power tool in a damp location is unavoidable, use

a residual current device (RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

Personal safety

▶ Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired

or under the influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in serious personal

injury.

▶ Use personal protective equipment. Always wear eye protection.

Protective equipment such as a dust mask, non-skid safety shoes, hard

hat or hearing protection used for appropriate conditions will reduce

personal injuries.

▶

Prevent unintentional starting. Ensure the switch is in the off-position

before connecting to power source and/or battery pack, picking up

or carrying the tool. Carrying power tools with your finger on the switch

or energising power tools that have the switch on invites accidents.

▶ Remove any adjusting key or wrench before turning the power tool

on. A wrench or a key left attached to a rotating part of the power tool

may result in personal injury.

▶ Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

▶ Dress properly. Do not wear loose clothing or jewellery. Keep your

hair, clothing and gloves away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving parts.

▶ If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used.

Use of dust collection can reduce dust-related hazards.

▶ Do not let familiarity gained from frequent use of tools allow you

to become complacent and ignore tool safety principles. A careless

action can cause severe injury within a fraction of a second.

Power tool use and care

▶ Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate for which it was designed.

▶ Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled with the switch is dangerous

and must be repaired.

▶ Disconnect the plug from the power source and/or remove the

battery pack, if detachable, from the power tool before making

any adjustments, changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the power tool

accidentally.

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

*2248872*

2248872 English 5

▶ Store idle power tools out of the reach of children and do not

allow persons unfamiliar with the power tool or these instructions

to operate the power tool. Power tools are dangerous in the hands of

untrained users.

▶ Maintain power tools and accessories. Check for misalignment or

binding of moving parts, breakage of parts and any other condition

that may affect the power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents are caused by poorly

maintained power tools.

▶ Keep cutting tools sharp and clean. Properly maintained cutting tools

with sharp cutting edges are less likely to bind and are easier to control.

▶ Use the power tool, accessories and tool bits etc. in accordance with

these instructions, taking into account the working conditions and

the work to be performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

▶ Keep handles and grasping surfaces dry, clean and free from oil and

grease. Slippery handles and grasping surfaces do not allow for safe

handling and control of the tool in unexpected situations.

Battery tool use and care

▶ Recharge only with the charger specified by the manufacturer. A

charger that is suitable for one type of battery pack may create a risk of

fire when used with another battery pack.

▶ Use power tools only with specifically designated battery packs. Use

of any other battery packs may create a risk of injury and fire.

▶ When battery pack is not in use, keep it away from other metal

objects, like paper clips, coins, keys, nails, screws or other small

metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a

fire.

▶ Under abusive conditions, liquid may be ejected from the battery;

avoid contact. If contact accidentally occurs, flush with water. If

liquid contacts eyes, additionally seek medical help. Liquid ejected

from the battery may cause irritation or burns.

▶ Do not use a battery pack or tool that is damaged or modified.

Damaged or modified batteries may exhibit unpredictable behaviour

resulting in fire, explosion or risk of injury.

▶ Do not expose a battery pack or tool to fire or excessive temperature.

Exposure to fire or temperature above 130° C (265 °F) may cause

explosion.

▶ Follow all charging instructions and do not charge the battery pack

or tool outside the temperature range specified in the instructions.

Charging improperly or at temperatures outside the specified range may

damage the battery and increase the risk of fire.

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

6 English 2248872

*2248872*

Service

▶ Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure that the safety of the power

tool is maintained.

▶ Never service damaged battery packs. Service of battery packs should

only be performed by the manufacturer or authorized service providers.

2.2 Drill/driver safety warnings

▶ Hold the power tool by insulated gripping surfaces, when performing

an operation where the fastener may contact hidden wiring. Fasteners

contacting a "live" wire may make exposed metal parts of the power tool

"live" and could give the operator an electric shock.

2.3 Additional safety precautions for screwdrivers

Personal safety

▶ Use the product only when it is in perfect working order.

▶ Never tamper with or modify the tool in any way.

▶ Use the auxiliary grips supplied with the power tool. Loss of control can

cause personal injury.

▶ Always hold the tool firmly with both hands on the grips provided. Keep

the grips clean and dry.

▶ Do not touch rotating parts – risk of injury!

▶ Wear suitable protective glasses, a hard hat, ear protection, protective

gloves and light respiratory protection while using the power tool.

▶ Wear protective gloves also when changing the tool. Touching the

accessory tool can result in cuts and burns.

▶ Wear eye protection. Flying fragments can injure the body and eyes.

▶ Before starting work, check the hazard class of the dust that will be pro-

duced when working. Use an industrial vacuum cleaner with an officially

approved protection class in compliance with the locally applicable dust

protection regulations. Dust from materials such as lead-based paint,

certain types of wood and concrete/masonry/stone containing quartz,

minerals or metal can be harmful to health.

▶ Make sure that the workplace is well ventilated and, where necessary,

wear a respirator appropriate for the type of dust generated. Contact with

or inhalation of the dust may cause allergic reactions and/or respiratory

or other diseases among operators or bystanders. Certain kinds of dust

are classified as carcinogenic such as oak and beech dust, especially

in conjunction with additives for wood conditioning (chromate, wood

preservative). Only specialists are permitted to handle material containing

asbestos.

▶ Take breaks and do physical exercises to improve the blood circulation

in your fingers. Exposure to vibration during long periods of work can

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

*2248872*

2248872 English 7

lead to disorders of the blood vessels and nervous system in the fingers,

hands and wrists.

Electrical safety

▶ Before beginning work, check the working area for concealed electric

cables or gas and water pipes. External metal parts of the power tool may

give you an electric shock if you damage an electric cable accidentally.

Power tool use and care

▶ Immediately switch off the power tool if the accessory tool jams. The

power tool might twist off-line.

▶

Wait until the power tool stops completely before you lay it down.

2.4 Battery use and care

▶ Observe the special regulations and instructions applicable to the trans-

port, storage and use of Li-ion batteries.

▶ Do not expose batteries to high temperatures, direct sunlight or fire.

▶ Do not disassemble, crush or incinerate batteries and do not subject them

to temperatures over 80 °C.

▶ Do not use or charge batteries that have suffered mechanical impact,

have been dropped from a height or show signs of damage. In this case,

always contact your Hilti Service.

▶ If the battery is too hot to touch it may be defective. In this case, place the

product in a non-flammable location, well away from flammable materials,

where it can be kept under observation and allowed to cool down. In this

case, always contact your Hilti Service.

3 Description

3.1 Overview of the product 1

@

1/4" hex. socket with locking

sleeve

;

Torque and drilling mode se-

lector ring

=

Gear speed selection switch

%

Forward/reverse selector

switch with safety lock

&

Grip

(

Lamp

)

Belt hook (optional)

+

Battery state of charge indica-

tor

§

Battery release button

/

Control switch (with electronic

speed control)

3.2 Intended use

The product described is a hand-held cordless drill/driver. It is designed for

driving and removing screws and for drilling in steel, wood and plastic.

▶ Use only Hilti Li-ion batteries of the B22 series with this product.

▶ Use only Hilti-approved battery chargers to charge these batteries. More

information is available from your Hilti Store or from www.hilti.group.

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

8 English 2248872

*2248872*

3.3 Charge status display

The charge status of the Liion battery is displayed after pressing the release

button.

Status Meaning

4 LEDs light up. Charge status: 75 % to 100 %

3 LEDs light up. Charge status: 50 % to 75 %

2 LEDs light up. Charge status: 25 % to 50 %

1 LED lights up. Charge status: 10 % to 25 %

1 LED flashes, the power tool is in

working order.

Charge status: < 10 %

Battery charge status cannot be displayed while the control switch is

pressed.

3.4 Items supplied

Drill / driver, operating instructions

Other system products approved for use with this product can be found

at your local Hilti Store or at: www.hilti.group

4 Technical data

4.1 Drill/driver

SFD 2-A

Rated voltage

10.8 V

Weight

1 kg

Speed in 1st gear

0 /min …

400 /min

Speed in 2nd gear

0 /min …

1,500 /min

Torque

0 Nm … 3.5 Nm

Torque (drill symbol)

12 Nm

Ambient temperature for operation

−17 ℃ … 60 ℃

Storage temperature

−20 ℃ … 70 ℃

4.2 Battery

Battery operating voltage

10.8 V

Ambient temperature for operation

−17 ℃ … 60 ℃

Storage temperature

−20 ℃ … 40 ℃

Battery charging starting temperature

4 ℃ … 40 ℃

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

*2248872*

2248872 English 9

4.3 Noise information and vibration values in accordance with EN

62841

The sound pressure and vibration values given in these instructions were

measured in accordance with a standardized test and can be used to

compare one power tool with another. They can also be used for a

preliminary assessment of exposure.

The data given represent the main applications of the power tool. However,

if the power tool is used for different applications, with different accessory

tools, or is poorly maintained, the data can vary. This can significantly

increase exposure over the total working period.

An accurate estimation of exposure should also take into account the times

when the tool is switched off, or when it is running but not actually being used

for a job. This can significantly reduce exposure over the total working period.

Identify additional safety measures to protect the operator from the effects

of noise and/or vibration, for example: maintaining the power tool and

accessory tools, keeping the hands warm, organization of work patterns.

Noise information

SFD 2-A

Typical A-weighted sound power level

75 dB

Typical A-weighted emission sound pressure level

64 dB

Uncertainty for the given sound levels

3 dB

Vibration values

SFD 2-A

Drilling in metal (a

h,D

)

1.9 m/s²

Uncertainty (K)

1.5 m/s²

5 Preparations at the workplace

CAUTION

Risk of injury by inadvertent starting!

▶ Before inserting the battery, make sure that the product is switched off.

▶ Remove the battery before making any adjustments to the power tool or

before changing accessories.

Observe the safety instructions and warnings in this documentation and on

the product.

5.1 Charging the battery

1. Before charging the battery, read the operating instructions for the

charger.

2. Make sure that the contacts on the battery and the contacts on the

charger are clean and dry.

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

10 English 2248872

*2248872*

3. Use an approved charger to charge the battery.

5.2 Inserting the battery

CAUTION

Risk of injury by short circuit or falling battery!

▶ Before inserting the battery, make sure that the contacts on the battery

and the contacts on the product are free of foreign matter.

▶ Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.

2. Push the battery into the battery holder until it engages with an audible

click.

3. Check that the battery is seated securely.

5.3 Removing the battery

1. Press the release buttons on the battery.

2. Pull the battery out of its holder in the device.

5.4 Fitting the belt hook (optional) 2

WARNING

Risk of injury. A falling power tool may present a risk of injury to yourself

and others.

▶ Check that the belt hook is fitted securely before beginning work.

The belt hook allows the power tool to be attached to a belt worn by

the operator. The belt hook can be fitted to allow attachment on the left

or right side of the body.

▶ Fit the belt hook.

5.5 Inserting/removing the accessory tool 5

1. Set the forward/reverse switch to the middle position or remove the

battery from the power tool.

2. Push the locking sleeve on the hex. socket forward and hold it securely in

this position.

3. Slide the accessory tool into the hex socket as far as it will go and release

the locking sleeve.

4. Check that the bit is held securely.

5. To remove the accessory tool, push the locking sleeve on the hex socket

forward and hold it in this position.

6. Remove the accessory tool from the hex socket and release the locking

sleeve.

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

*2248872*

2248872 English 11

6 Operation

CAUTION

Risk of injury by short circuit or falling battery!

▶ Before inserting the battery, make sure that the contacts on the battery

and the contacts on the product are free of foreign matter.

▶ Make sure that the battery always engages correctly.

Observe the safety instructions and warnings in this documentation and on

the product.

6.1 Selecting the gear 3

▶ Select the desired gear by adjusting the two gear selector switches.

6.2 Setting forward or reverse rotation 4

An interlock prevents switching while the motor is running.

The control switch is locked when the forward/reverse switch is in the

middle position (safety lock).

▶ Set the forward/reverse switch to the desired direction of rotation.

6.3 Switching on

▶ Press the control switch.

Speed can be controlled steplessly right up to maximum by varying

how far the control switch is pressed in.

6.4 Screwdriving

1. Set the torque and operating mode selector ring to the required torque.

2. Set the forward/reverse switch to the desired direction of rotation.

6.5 Drilling

1.

Set the torque and operating mode selector ring to the symbol.

2. Set the forward/reverse switch to the “forward” position.

6.6 Switching off

▶ Release the control switch.

7 Care and maintenance

WARNING

Risk of injury with battery inserted !

▶ Always remove the battery before carrying out care and maintenance

tasks!

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

12 English 2248872

*2248872*

Care and maintenance of the tool

• Carefully remove stubborn dirt.

• Clean the air vents carefully with a dry brush.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning

agents containing silicone as these can attack the plastic parts.

Care of the Liion batteries

• Keep the battery free from oil and grease.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning

agents containing silicone as these may attack the plastic parts.

• Avoid ingress of moisture.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals

and make sure that they all function correctly.

• Do not operate the product if signs of damage are found or if parts

malfunction. Have it repaired immediately by Hilti Service.

• After cleaning and maintenance, fit all guards or protective devices and

check that they function correctly.

To help ensure safe and reliable operation, use only genuine Hilti spare

parts and consumables. Spare parts, consumables and accessories

approved by Hilti for use with the product can be found at your local

Hilti Store or online at: www.hilti.group.

8 Transport and storage of cordless tools

Transport

CAUTION

Accidental starting during transport !

▶ Always transport your products with the batteries removed!

▶ Remove the battery.

▶ Never transport batteries in bulk form (loose, unprotected).

▶ Check the tool and batteries for damage before use after long periods of

transport.

Storage

CAUTION

Accidental damage caused by defective or leaking batteries !

▶ Always store your products with the batteries removed!

▶ Store the tool and batteries in a place that is as cool and dry as possible.

▶ Never store batteries in direct sunlight, on heating units or behind a

window pane.

▶ Store the tool and batteries in a place where they cannot be accessed by

children or unauthorized persons.

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

*2248872*

2248872 English 13

▶ Check the tool and batteries for damage before use after long periods of

storage.

9 Troubleshooting

9.1 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable

to remedy the problem by yourself, please contact Hilti Service.

9.1.1 Troubleshooting

Trouble or fault Possible cause Action to be taken

The power tool does

not work.

The battery is not fully

inserted.

▶ Push the battery in

until it engages with

an audible double

click.

Low battery. ▶ Change the battery

and charge the empty

battery.

The on/off button

cannot be pressed,

i.e. the button is

locked.

The forward/reverse

selector switch is in the

middle position.

▶ Push the

forward/reverse

switch to the left or

right.

The battery runs

down more quickly

than usual.

Very low ambient tem-

perature.

▶ Allow the battery to

warm up slowly to

room temperature.

The battery does

not engage with an

audible double click.

The retaining lugs on the

battery are dirty.

▶ Clean the retaining

lugs and push the

battery in until it

engages. Contact

Hilti Service if the

problem persists.

The tool or battery

gets very hot.

The tool is overloaded

(application limits ex-

ceeded).

▶ Pay attention to the

power and perfor-

mance rating of the

product before using

it, i.e check its suitabil-

ity for the job on hand.

See the “Technical

data” section.

9.2 Disposal

Most of the materials from which Hilti tools and appliances are manu-

factured can be recycled. The materials must be correctly separated before

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

14 English 2248872

*2248872*

they can be recycled. In many countries, your old tools, machines or appli-

ances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti

representative for further information.

Battery disposal

Improper disposal of batteries can result in health hazards from leaking

gases or fluids.

▶ DO NOT send batteries through the mail!

▶ Cover the terminals with a non-conductive material (such as electrical

tape) to prevent short circuiting.

▶ Dispose of your battery out of the reach of children.

▶ Dispose of the battery at your Hilti Store, or consult your local govern-

mental garbage disposal or public health and safety resources for disposal

instructions.

▶ Do not dispose of power tools, electronic equipment or batteries as

household waste!

10 RoHS (Restriction of Hazardous Substances)

Click on the link to go to the table of hazardous substances:

• qr.hilti.com/r2907507

There is a link to the RoHS table, in the form of a QR code, at the end of this

document.

11 Manufacturer’s warranty

▶ Please contact your local Hilti representative if you have questions about

the warranty conditions.

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

*2248872*

2248872 Français 15

1 Indications relatives à la documentation

1.1 À propos de cette documentation

• Lire intégralement la présente documentation avant la mise en service.

C'est la condition préalablement requise pour assurer la sécurité du travail

et un maniement sans perturbations.

• Bien respecter les consignes de sécurité et les avertissements de la

présente documentation ainsi que celles figurant sur le produit.

• Toujours conserver le mode d'emploi à proximité du produit et uniquement

le transmettre à des tiers avec ce mode d'emploi.

1.2 Explication des symboles

1.2.1 Avertissements

Les avertissements attirent l'attention sur des dangers liés à l'utilisation du

produit. Les termes de signalisation suivants sont utilisés :

DANGER

DANGER !

▶ Pour un danger imminent qui peut entraîner de graves blessures corpo-

relles ou la mort.

AVERTISSEMENT

AVERTISSEMENT !

▶ Pour un danger potentiel qui peut entraîner de graves blessures corpo-

relles ou la mort.

ATTENTION

ATTENTION !

▶ Pour attirer l'attention sur une situation pouvant présenter des dangers

entraînant des blessures corporelles légères ou des dégâts matériels.

1.2.2 Symboles dans la documentation

Les symboles suivants sont utilisés dans la présente documentation :

Lire le mode d'emploi avant d'utiliser l'appareil

Pour des conseils d'utilisation et autres informations utiles

Maniement des matériaux recyclables

Ne pas jeter les appareils électriques et les accus dans les ordures

ménagères

1.2.3 Symboles dans les illustrations

Les symboles suivants sont utilisés dans les illustrations :

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

16 Français 2248872

*2248872*

Ces chiffres renvoient à l'illustration correspondante au début du

présent mode d'emploi

La numérotation détermine la séquence des étapes de travail dans

l'image et peut se différencier de celles des étapes de travail dans le

texte

Les numéros de position sont utilisés dans l'illustration Vue d’en-

semble et renvoient aux numéros des légendes dans la section Vue

d'ensemble du produit

Ce signe doit inviter à manier le produit en faisant particulièrement

attention.

1.3 Symboles spécifiques au produit

1.3.1 Symboles sur le produit

Les symboles suivants sont utilisés sur le produit :

Perçage sans percussion

Tours par minute

Vitesse nominale à vide

Courant continu

Accu lithium-ions

Série de type d'accu Li-Ion Hilti utilisée. Observer les instructions au

chapitre Utilisation conforme à l'usage prévu.

Le produit prend en charge la transmission de données sans fil qui

est compatible avec les plates-formes iOS et Android.

1.4 Informations produit

Les produits sont destinés aux professionnels et ne doivent

être utilisés, entretenus et réparés que par un personnel autorisé et formé.

Ce personnel doit être spécialement instruit quant aux dangers inhérents

à l'utilisation de l'appareil. Le produit et ses accessoires peuvent s'avérer

dangereux s'ils sont utilisés de manière incorrecte par un personnel non

qualifié ou de manière non conforme à l'usage prévu.

La désignation du modèle et le numéro de série figurent sur sa plaque

signalétique.

Printed: 05.07.2019 | Doc-Nr: PUB / 5501914 / 000 / 00

ページが読み込まれています...

Hilti SFD 2-A 取扱説明書

Hilti SFD 2-A 取扱説明書

他の言語で

関連論文