ResMed Humidifier III ST-A ユーザーマニュアル

VPAP™ III ST-A with QuickNav

User Guide

English • 简体中文 • 繁體中文

ResMed Ltd (Manufacturer) 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia

ResMed Corp (US Designated Agent) 14040 Danielson Street Poway CA 92064-6857 USA

ResMed (UK) Ltd (EU Authorized Representative) 96 Milton Park Abingdon Oxfordshire OX14 4RY UK

ResMed Ofﬁces Australia, Austria, Belgium, Brazil, China, Finland, France, Germany, Greece, Hong Kong, India, Ireland, Italy, Japan,

Malaysia, Mexico, Netherlands, New Zealand, Norway, Portugal, Singapore, South Africa, Spain, Sweden, Switzerland, UK, USA (see

www.resmed.com for contact details).

VPAP III ST-A with QuickNav

Protected by patents: AU 697652, AU 699726, AU 713679, AU 2002233025, CA 2235939, CN ZL02804936.5, EP 0661071, EP 0858352,

HK 1065483, JP 3638613, JP 4083154, US 5199424, US 5522382, US 6213119, US 6240921, US 6705315. Other patents pending.

Protected by design registrations: AU 147283, AU 147335, CH 128.710, CH 128.711, DE 40202007, DE 40202008, ES 153515, ES

153516, ES 156136, FR 021395, GB 3001819, GB 3001820, JP 1164265, JP 1164266, NZ 527088, SE 75598, SE 75600, US D467335,

US D476077, US D477868, US D487311.

SmartStart, TiCONTROL, VPAP, and Vsync are trademarks of ResMed Ltd and SmartStart and VPAP are registered in U.S. Patent and

Trademark Ofﬁce.

Global leaders in sleep and respiratory medicine www.resmed.com

248210/4 08 10

VPAP™ III ST-A with

QuickNav

USER

APAC

VPAP™ III ST-A with QuickNav

User Guide

English

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

User/Owner Responsibility 1

Medical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Intended Use 1

Contraindications 1

Adverse Effects 1

The VPAP III ST-A with QuickNav . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Masks 2

Humidifiers 2

Setting up the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Attaching a Humidifier 4

Using the LCD QuickNav Screen and Keypad 4

Starting Treatment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Patient Standby Screens 6

Using the Mask-Fit Feature 7

Stopping Treatment 7

How to Use the Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

QuickNav Screen 8

Menu Navigation 8

Patient Treatment Menu 8

Patient Summary Menu 8

Patient Settings Menu 9

Patient Options Menu 10

The Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Alarms Troubleshooting 11

Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Servicing 14

Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

General Warnings and Cautions 18

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

1Introduction

English

Introduction

The VPAP™ III ST-A with QuickNav™ is a bilevel pressure support ventilator specifically

designed for non-invasive mask ventilation.

This user manual contains the information you need for the correct use of your

VPAP III ST-A with QuickNav.

User/Owner Responsibility

The user or owner of this system shall have sole responsibility and liability for any injury to

persons or damage to property resulting from:

• operation which is not in accordance with the operating instructions supplied

• maintenance or modifications carried out unless in accordance with authorised

instructions and by authorised persons.

Please read this manual carefully before use.

This manual contains special terms and icons that appear in the margins to draw your

attention to specific and important information.

• Warning alerts you to possible injury.

• Caution explains special measures for the safe and effective use of the device.

• Note is an informative or helpful note.

Medical Information

Intended Use

The VPAP III ST-A system is intended to provide non-invasive ventilation for patients with

respiratory insufficiency or obstructive sleep apnoea (OSA), in the hospital or home.

Contraindications

This device should not be used if you have an insufficient respiratory drive to endure brief

interruptions in non-invasive ventilation therapy. This device is not a life support ventilator

and may stop operating with power failure or in the unlikely event of certain fault conditions.

If you have any of the following conditions, tell your doctor before using this device:

• acute sinusitis or otitis media

• epistaxis causing a risk of pulmonary aspiration

• conditions predisposing to a risk of aspiration of gastric contents

• impaired ability to clear secretions

• hypotension or significant intravascular volume depletion

• pneumothorax or pneumomediastinum

• recent cranial trauma or surgery.

Adverse Effects

You should report unusual chest pain, severe headache or increased breathlessness to your

physician. An acute upper respiratory tract infection may require temporary discontinuation

of treatment.

The following side effects may arise during the course of therapy:

• drying of the nose, mouth or throat

• bloating

2

• ear or sinus discomfort

• eye irritation

• mask-related skin irritations

• chest discomfort.

The VPAP III ST-A with QuickNav

The VPAP III ST-A with QuickNav comprises:

• VPAP III ST-A with QuickNav (shown above)

• Power cord

• Carry bag

• 2 m air tubing.

The following accessories may be purchased separately:

• 3 m air tubing

• Medium (52 cm) air tubing for the HumidAire and ResMed Passover humidifiers

• Hypoallergenic air filter.

!

WARNING

• Do not connect any device to the communication ports. Although your

health care provider may connect specially designed devices to the

communication ports of this device, connection of other devices could result

in injury, or damage to the unit.

• In the clinical environment, any PC that is used with this device must be at

least 1.5 m away from, or at least 2.5 m above the patient. It must also

comply with IEC 60950 or equivalent.

Masks

You will also need a ResMed mask (supplied separately). For information on using your

mask, see your mask manual. For the latest available masks, or to select the appropriate

setting for your mask, see www.resmed.com on the Products page under Service &

Support.

Humidifiers

A humidifier may be required if you are experiencing dryness of the nose, throat or mouth.

This device is compatible for use with the following ResMed humidifiers:

• HumidAire 2i™ heated humidifier

• HumidAire 2iC™ passover humidifier

DC Power Socket

AC Power Socket

Air filter cover

Power switch

Communication ports

Removable

front cover

Handle

LCD screen

Control panel

Air outlet

3Setting up the device

English

• HumidAire™ heated humidifier

• ResMed Passover humidifier.

!

WARNING

The HumidAire 2i, HumidAire 2iC, HumidAire heated humidifier and the ResMed

Passover are compatible for use with this device. Please refer to Warnings on

page 18.

Setting up the device

Place the device on a flat surface near the head of your bed.

!

CAUTION

• Be careful not to place the device where it can be bumped or where

someone is likely to trip over the power cord.

• Make sure the area around the flow generator is dry and clean. It should also

be clear of bedding, clothes and other potential blockages.

1 Connect the power cord.

Note: ResMed recommends using the AC power cord supplied with the unit. If a

replacement power cord is required, contact your ResMed service centre.

2 Plug the free end of the power cord into a power outlet.

!

CAUTION

Do not connect both AC and DC power cords to the device at the same time,

unless otherwise specified.

!

WARNING

• Make sure the power cord and plug are in good condition and the

equipment is not damaged.

• The air filter cover protects the device in the event of accidental liquid

spillage onto the device. Ensure that the air filter and air filter cover are fitted

at all times.

3 Connect one end of the air tubing firmly onto the air outlet of the device.

Power switch

AC locking clip

AC power cord

4

!

WARNING

Only ResMed air tubing should be used with your flow generator. A different

type of air tubing may alter the pressure you actually receive and reduce the

effectiveness of your treatment. Do not use conductive or anti-static hoses or

tubes.

4 Connect your mask system to the free end of the air tubing.

Attaching a Humidifier

!

WARNING

When using a humidifier, position it lower than your sleeping position, so that

any excess condensation drains back into the water chamber, and at the same

level or lower than the device.

Notes:

• You must activate the humidifier option in the menus if you are using a HumidAire or

Passover humidifier.

• For details on using humidifiers, please see you relevant user manual.

HumidAire 2i/2iC Humidifier

The HumidAire 2i or 2iC attaches to the front of the device to provide heated or passover

humidification, respsectively. No other accessories are required for its use. The

VPAP III ST-A with QuickNav automatically detects the presence of the HumidAire 2i.

HumidAire or Passover Humidifier

Medium size (52 cm) air tubing is a necessary accessory for connecting the device to the

HumidAire or Passover humidifier.

Note: Place the device on top of the humidifier. Do not place the device underneath the

humidifier. (This is to avoid water spilling into the device.)

Using the LCD QuickNav Screen and Keypad

The control panel of this device includes an LCD screen, LEDs and keypad.

LCD Screen

The LCD screen displays the menus, treatment screens and alarm conditions.

Alarm LEDs

Alarm Mute

Start/Stop

Exit key

Enter (Soft) key

Up/Down key

LCD QuickNav screen

(green)

QuickView

(red)

Therapy LED

5Starting Treatment

English

To assist you in adjusting the device, the keypad and LCD are equipped with a backlight. The

LCD backlight comes on when the device is turned on or when you press a key, and turns

off after two minutes. The LCD backlight may be set to be on continually. The keypad

backlight is on at all times when the device is powered.

LEDs

The Therapy LED (white) may be on during treatment, if enabled by your clinician. The

Alarm LEDs (Red/Yellow) are on during an alarm condition or during alarm testing.

Keypad Keys

The device keypad has the following keys:

Starting Treatment

The device should be assembled beside your bed with the air tubing and mask system

connected.

1 Turn the power switch at the back of the device to on (I).

When the device is turned on, the Patient Standby screen is displayed.

Notes:

• If you have the HumidAire 2i attached, see “Using the HumidAire 2i Warm-up

Feature” on page 6.

• When the device is turned on, the alarm will sound a test beep and the red and yellow

LEDs will flash. To test the alarm manually, or to change the volume, see “Testing the

Alarm” on page 11.

2 Fit your mask as described in the mask user instructions.

3 Lie down and arrange the air tubing so that it is free to move if you turn in your sleep.

Key Function

Start/Stop • Starts or stops treatment.

• Extended hold for at least two seconds starts the MaskFitting

feature.

QuickView • Clinical menu function key. Clinical use only.

Alarm Mute • Press once to mute alarms. Press a second time to un-mute

alarms. If the problem is still present, the alarm will sound again

after two minutes. See “Alarm Mute Key” on page 11.

Exit (red)

• Allows you to exit the current menu or go back through the

menus. The function of this key is to exit from the current menu

or setting

.

Up/Down • Allows you to scroll through the device menus, submenus and

settings.

Enter (green)

• Allows you to enter or change the menu or function highlighted

on the LCD screen. Functions of this key includes enter, change

and apply, and it also operates as a soft key.

6

!

CAUTION

Do not leave long lengths of air tubing around the top of your bed. It could twist

around your head or neck while you are sleeping.

4 To start treatment, press the Start/Stop key

or

if the SmartStart function is enabled, simply breathe into the mask and treatment will

begin.

Patient Standby Screens

The Patient Standby screens are displayed when the device is turned on. Depending on your

configuration and settings, these screens may display as follows.

Using the HumidAire 2i Warm-up Feature

*

If using a HumidAire 2i with the device, you can use the Warm-

up feature to pre-heat the water in the humidifier prior to

starting treatment. The humidifer will be automatically

detected when the device is turned on and the standby screen

will give you the option to start warming up the humidifier.

After stopping treatment, the device will continue to blow air

gently to assist cooling of the heater plate.

* If you do not have a H2i attached and/or your clinician has not enabled Ramp time, these options

will not appear.

Ramp Time

*

Ramp time is a feature which can be enabled by your clinician.

If you have difficulty becoming accustomed to the full pressure,

select a ramp time. The airflow will start very gently and slowly

increase to full operating pressure over the selected ramp time.

If your clinician has set a maximum ramp time, the Set Ramp

option is displayed on the Patient Standby screen. Ramp time

can be altered in five-minute increments (from OFF to a

maximum ramp time set by your clinician) by using the Up/

Down key.

Patient Home Screen/Treatment Screen

This screen displays the time and date, the pressure bar and

the remaining Ramp time, if a Ramp time has been set.

ST

Set Ramp: 40min

Warm-up the Humidifier

22:23

12 Oct 2006

ST

Humidifier Warning

Set Ramp: 40min

ST

Ramp:

19:45

21:53

12 Oct 2006

7Starting Treatment

English

Using the Mask-Fit Feature

This device includes a mask-fit feature to help you fit your mask properly. If a Ramp time is

selected, the mask can be adjusted at a pressure closer to the prescribed pressure. To use

the mask-fit feature:

1 Fit your mask as described in the user instructions.

2 Hold down the Start/Stop key for at least two seconds until air pressure delivery starts

1

.

The flow generator will ramp to the mask-fit pressure

2

and will remain at this pressure

for three minutes.

3 If necessary, adjust your mask, mask cushion and headgear to reduce leak and check

your mask-fit star rating again on the LCD screen.

4 After three minutes, treatment will begin.

• If you do not wish to wait three minutes, hold down the Start/Stop key for at least

two seconds and treatment will begin immediately.

• If you press the Start/Stop key for less than two seconds, the device will return to

standby mode.

Stopping Treatment

To stop treatment at any time, remove your mask and press the Start/Stop key

or

if the SmartStart function is enabled, simply remove your mask and treatment will end

(SmartStop is not applicable with the "Mir Full" mask setting and certain alarms; see

“SmartStart™” on page 10).

1 The mask-fit feature can also be accessed from the Patient Settings Menu.

2 The mask-fit pressure is the set treatment pressure or 10 cm H

2

O, whichever is greater.

The LCD also displays a mask-fit star rating from zero to

five stars. Three to five stars indicate a good fit. Zero to

two stars indicate that you should adjust your mask.

The mask-fit star rating display disappears after three

minutes.

LK: 1.7

Press: 10

SETTINGS

21:53

Done

Mask Fitting

Good

8

How to Use the Menus

QuickNav Screen

Menu Navigation

Patient Treatment Menu

The patient treatment menu displays a pressure bar and any remaining set Ramp time. See

“Patient Home Screen/Treatment Screen” on page 6.

Patient Summary Menu

The patient summary menu allows you to view details about the time used, a summary of

your device settings, and the current software version of your VPAP III ST-A with QuickNav.

To scroll through the menu icons or items

within a menu or submenu:

Press the Up/Down key to highlight your

selection.

To enter a menu or submenu: Press Enter.

To change a setting or activate a

function:

1. Press Enter.

2. Press the Up/Down key until the

desired setting appears.

3. Press Enter to select the setting.

To exit from changing settings or

options:

Press Enter or Exit

.

*

* Pressing Exit will not cancel changes you have made to the settings.

To exit out of a menu or submenu: Press Exit.

To scroll through pages or time periods,

using the soft key display (when available):

Press Enter.

SUMMARY

LK:

1.7 Vt: 780 RR: 10 MV: 7.8

21:53

EFFICACY DATA

6mths

Leak:

14.4

L/min

Vt:

0400-1000

ml

RR:

8-15

bpm

MV:

3.2-15.0

L/min

% Spont. T:

70

%

% Spont. C:

77

%

Title bar

Soft key display

Scroll bar

Menu icons

Main window

Therapy Status bar

9How to Use the Menus

English

The below example shows the progression of screens as you navigate to the Usage Data

from the Patient Summary Menu.

The data displayed in the Summary menu screens is view only. In some Summary menu

screens, pressing Enter when the soft key in the title bar is selected allows you to choose

a time period over which the data is measured (eg, a day, a week, a month, etc.).

Patient Settings Menu

The Patient Settings menu allows you to view and change settings such as mask type, tube

length and the humidifier used. You can also access the Mask-Fit feature.

!

WARNING

If these settings do not match your system set-up, this may alter the pressure

you actually receive and reduce the effectiveness of your treatment.

123

SUMMARY

LK:

1.7 Vt: 780 RR: 10 MV: 7.8

21:53

EFFICACY DATA

USAGE DATA

ALARM HISTORY

EVENT HISTORY

SETTINGS SUMMARY

SERVICING

SUMMARY

LK:

1.7 Vt: 780 RR: 10 MV: 7.8

21:53

EFFICACY DATA

USAGE DATA

ALARM HISTORY

EVENT HISTORY

SETTINGS SUMMARY

SERVICING

SUMMARY

LK:

1.7 Vt: 780 RR: 10 MV: 7.8

21:53

USAGE DATA

6mths

Used Since:

12 Oct 2006

Used:

740

hrs

102/106

days

Usage: 7: 15 hrs/day

LK:

1.7

Vt:

780

RR:

10

MV:

7.8

SETTINGS

21:53

Mask:

MIR FULL

Humidifier: None

Tube Length: 2m

Check Mask Fit

SmrtStrtStp: Off

Function Default Function Description Settings

Mask MIR

FULL

Selects your mask type. See www.resmed.com or

ask your clinician for the

correct setting for your mask

type.

Humidifier NONE Selects the type of humidifier to

be used with the device.

NONE, H2i (HumidAire 2iC),

PASSOVER, HUMIDAIRE

If the HumidAire 2i is used, it

is automatically detected

and H2i is displayed.

Tube Length 2 m Selects the length of air tubing

connecting your mask to the

device.

2 m,

3 m

Check Mask-

Fit

Allows you to check your mask-

fit star rating.

View only

10

Patient Options Menu

The Patient Options menu allows you to set the local time, date and language and to test

and change the alarm volume.

SmartStart™

(SmrtStrtStp)

OFF If SmartStart is enabled, the

device will start automatically

when you breathe into the mask

and will stop automatically when

you take your mask off

(SmartStop). This means you do

not have to press the Start/

Stop key to begin or end

treatment.

*, †

ON/OFF

* If you select “Mir Full” as the mask option, SmartStop is automatically disabled. SmartStart may

not work with a full face mask due to safety features of the mask.

† When the Leak or Low MV Alarms are set to ON, SmartStop is automatically disabled. SmartStop

cannot be used with the Leak or Low MV Alarms because, if either of these conditions occur,

SmartStop will stop treatment before the alarm signal is activated.

Function Function Description Default Settings

Setup • Alarm Vol/Test: Allows you to

change and test the alarm

volume.

Note: When you select the volume

level and when you press enter, the

alarm will beep at the selected

volume as a test.

Medium Low, Medium and High.

• LCD Backlight AUTO ON/AUTO

Clock Allows you to set the time and date.

Language Selects the menu language.

*

* A tick will appear next to the currently selected language.

English English, German, French,

Italian, Spanish, Dutch,

Portuguese.

Function Default Function Description Settings

OPTIONS

LK:

1.7 Vt: 780 RR: 10 MV: 7.8

21:53

SETUP

CLOCK

LANGUAGE

11The Alarms

English

The Alarms

This device is fitted with alarms to alert you to changes that will affect your treatment.

Alarm Mute Key

You can mute an alarm by pressing the Alarm Mute key once. Pressing this key a

second time will un-mute the alarm. If the problem is still present, the alarm will sound again

after two minutes. An alarm LED will remain lit for as long as the problem is present. The

Title bar of the LCD will display the alarm description while the alarm is muted.

Testing the Alarm

When the device is turned on, the LEDs will flash and the alarm will beep to confirm that the

alarm is working.

Setting the Alarm Volume

You can set and test the alarm volume from the Patient Options Menu. The alarm will beep

at the selected volume when you press Enter.

All menus remain available during an alarm. Treatment screens are not viewable during an

alarm condition.

Alarms Troubleshooting

The most common reason for an alarm to sound is because the system has not been

properly assembled. Check that the air tubing has been properly attached to the flow

generator and mask (and humidifier if used).

When an alarm has been activated, the LCD screen will display either alarm information or

recommended instructions for you or your clinician.

Note: The alarm actions listed below are based on having the appropriate alarm settings for

your therapy. When an alarm is activated, consult your clinician.

!

CAUTION

In the event of power failure or machine malfunction, remove the mask to avoid

rebreathing your exhaled air.

Warning Signal/Cause Action

For all the medium priority alarms listed below, you will hear a

single intermittent tone and

the

yellow LED will flash.

LCD: LCD turns off

The flow generator stops delivering air pressure.

• Power failure.

• Power cord is disconnected or

device switched off while

delivering treatment (without

pressing the Start/Stop key).

Remove your mask until power is restored.

Notes:

• Treatment will re-start when power is restored.

• Unless muted, the alarm will sound for at least

two minutes in the event of a power failure.

LCD: CHECK TUBE

The flow generator stops delivering air pressure.

• Air tubing disconnected from the

HumidAire 2i/2iC.

1. Check that the air tubing is connected

properly to the HumidAire 2i/2iC.

2. Check that the HumidAire 2i/2iC or front cover

is connected properly to the flow generator.

12

3. Turn the device off and on again at the power

switch.

• There is a blockage in the air

circuit.

1. Check the air circuit for a blockage.

2. Remove blockage.

3. Re-start therapy.

• Hardware failure. If the alarm persists, return the unit to ResMed

for servicing.

LCD: IPAP LOWER

Device is operating outside device

specifications.

Continue using and contact your clinician about

this alarm. Device settings may require

adjustment.

LCD: SYSTEM ERROR-xxx TURN OFF & CALL SERVICE!

The flow generator stops delivering air pressure.

Component failure. • Return the device for servicing.

• DO NOT USE THE DEVICE.

LCD: HIGH LEAK!!!

High mask leak for more than 20

seconds.

Adjust the mask to minimise leak. See “Using

the Mask-Fit Feature” on page 7.

LCD: LOW PRESSURE:XX

• Air pressure at the mask has fallen

below the alarm setting level.

• Mask is removed while SmartStop

has been disabled.

1. Check that the air tubing is connected

properly.

2. Turn the device off and on again at the power

switch. If the alarm persists, return the unit to

ResMed for servicing.

LCD: HIGH PRESSURE:XX

Mask pressure exceeds alarm setting

level.

1. The treatment will stop.

2. Turn power off.

3. Turn power back on.

4. Try using the flow generator one more time.

5. If the high pressure alarm activates

repeatedly, discontinue use and return to

ResMed for servicing. If the alarm does not

recur, then continue to use as normal.

LCD: LOW MV:XX

Minute ventilation level has dropped

below the alarm setting level.

Contact your clinician.

Warning Signal/Cause Action

13Cleaning and Maintenance

English

Cleaning and Maintenance

You should regularly carry out the cleaning and maintenance described in this section.

LCD: NO MASK VENT

• Connection of a non-vented mask.

• Mask expiratory flow port (vent)

may be blocked.

• Use of supplemental oxygen with

a vented mask.

• Ensure your mask has an expiratory flow port

(vent).

• Ensure your mask expiratory flow ports

(vents) are not blocked.

• Contact your clinician.

Note: The non-vented mask alarm activates within

30 seconds (15 sec on average) of using therapy

with a non-vented mask.

Daily Cleaning

Mask

Clean the mask according to the instructions supplied with the mask.

Air tubing

Disconnect the air tubing from the device (and humidifier, if used) and

store the tubing and mask in a clean, dry place until next use.

CAUTION

Do not store the air tubing in direct sunlight as the tubing may harden over

time and eventually crack.

Humidifier

If you are using a humidifier, clean it according to the instructions supplied

with the humidifier.

Weekly Cleaning

1

Remove the air tubing from the device and the mask.

2

Wash the air tubing in warm water using mild detergent. Rinse thoroughly, hang and

allow to dry.

3

Reconnect the air tubing to the air outlet and mask.

CAUTION

• Do not use bleach, chlorine-, alcohol- or aromatic-based solutions

(including all scented oils), moisturising or antibacterial soaps to clean the

air tubing or the device. These solutions may cause hardening and reduce

the life of the product.

• Do not hang the air tubing in direct sunlight as the tubing may harden over

time and eventually crack.

Periodic Cleaning

1

Clean the exterior of the device with a damp cloth and mild liquid soap.

2

Inspect the air filter to check if it is blocked by dirt or contains holes. See “Replacing the

Air Filter” on page 14.

WARNING

Beware of electric shock. Do not immerse the flow generator or power cord in

water. Always unplug the flow generator before cleaning and be sure that it

is dry before reconnecting.

Warning Signal/Cause Action

14

Servicing

This device is intended to provide safe and reliable operation when operated and maintained

in accordance with the instructions provided by ResMed. To ensure that your device

continues to provide optimum performance it is recommended that this product (VPAP III

ST-A with QuickNav) be inspected by an authorised ResMed Service Centre five years from

the date of purchase. Applicable ResMed warranty details are provided with the device at

the time of original supply. Of course, as with all electrical devices, if any irregularity

becomes apparent, you should exercise caution and have the device inspected by an

authorised ResMed service centre.

If you feel that your device is not performing properly, see “Troubleshooting” on page 15.

!

CAUTION

Inspection and repair should only be performed by an authorised agent. Under

no circumstances should you attempt to service or repair the flow generator

yourself.

Helpful Hints

Travelling with the VPAP III ST-A with QuickNav

International Use

Your device has an internal power adapter that enables it to operate in other countries. It will

operate on power supplies of 100–240V, 50–60Hz and 110V, 400 Hz. No special adjustment

is necessary, but you will require an approved power cord for that country.

Using a Battery to Power the Device

Information regarding suitable DC and battery power supplies for this device can be found

on www.resmed.com on the Products page under Service and Support > Ventilation

Accessories.

Inverter or UPS

The power specifications for an inverter or a UPS are listed in the following table.

CAUTION

Do not attempt to open the device. There are no user serviceable parts inside.

Repairs and internal servicing should only be performed by an authorised

service agent.

Replacing the Air Filter

Inspect the air filter every month to check if it is blocked by dirt or contains holes. With normal

use of the device, the air filter needs to be replaced every six months (or more often if your

device is in a dusty environment). To replace the air filter:

1

Remove the air filter cover at the back of the device.

2

Remove and discard the old air filter.

3

Insert a new filter with the blue tinted side facing out.

4

Replace the air filter cover.

WARNING

Do not wash the air filter. The air filter is not washable or reusable.

ページが読み込まれています...

ResMed Humidifier III ST-A ユーザーマニュアル

このマニュアルも適しています

ResMed Humidifier III ST-A ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント