3-254-402-12(1)
XAV-77
Media Center/
Receiver
Installation/Connections
GB
CT
© 2003 Sony Corporation
Notice to dealers and installers
Please return this manual to the customer after the installation is completed.
2
Unit is designed for negative ground
12 V DC systems only
The unit cannot be used in trucks or other cars
with 24 V systems. Otherwise, there is a risk of fire
and damage.
Do not disassemble or remodel the
unit
This can cause electric shock, personal injury or
fire. Do not connect any other system’s power
supply cord to this unit’s power supply cord
directly. If you are in any doubt about the safe
installation of this unit, please consult your nearest
Sony dealer.
Do not install in locations which
interfere with airbag operation
Otherwise there is a risk of accidents and injury.
Use only the specified fuse
When replacing the fuse, be sure to use only a fuse
of the same rating (ampere rating). Otherwise
there is a risk of fire.
Do not block ventilation
If the unit is placed under the floor carpet, floor
mat, or otherwise covered, the ventilation
openings and heat sink cannot provide sufficient
cooling, leading to overheating and the risk of fire
or serious accidents.
Cautions
• Do not get the wires under a screw, or caught in
moving parts (e.g. seat railing).
• Before making connections, turn the car ignition
off to avoid short circuits.
• Connect the yellow and red power input leads
only after all other leads have been connected.
• Run all ground wires to a common ground
point.
• Be sure to insulate any loose unconnected wires
with electrical tape for safety.
Notes on the power supply cord (yellow)
• When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
Precautions
On safety
Comply with the Traffic Laws in your country.
3
Table of Contents
Precautions .................................................................................................................... 2
Parts List ........................................................................................................................ 4
1 Installing the Main Unit .......................................................................................... 5
Before installation................................................................................................................. 5
Installation procedure..........................................................................................................7
Installing the connection box XA-114 ................................................................................ 9
Hooking up the connection box ......................................................................................... 9
2 Main Unit Connections.......................................................................................... 10
Connection Example ................................................................................................... 11
Connecting Information ............................................................................................. 13
Using the tap ....................................................................................................................... 13
Connecting the parking cord ............................................................................................ 13
3 Car Systems Connections ...................................................................................... 14
4 After Installation and Connections ...................................................................... 16
Removing the Front Panel Plate ................................................................................ 17
4
12 3
4
*1
56
78 9
q; qa qs
Parts List
The numbers in the list are keyed to those in the instructions.
×2
*
1
Packed while being fixed to the main unit.
*
2
Use this to replace the fuse or dismount the unit.
Refer to the Operating Instructions for details.
CAUTION
Handle the bracket
q; carefully to avoid
injuring your fingers.
×2
×4
qd qf qg
*2
2.5 m
5
Installation angle
The unit should be installed within an
angle of 25 degrees from horizontal. If
this angle is exceeded, the monitor may
not open up or retract properly.
Note
Keep the units and connection cables
apart.
The Media Center main unit and the
connection box 1 should not be in close
proximity.
1 Installing the Main Unit
Before installation
This unit is designed to be completely safe, but if not installed
correctly, it can cause accidents. Be sure to verify the following
points before installation.
Install the main unit to the in-dash location, and the connection
box under the navigator’s seat, etc.
• If the monitor in the opened position is close to a air-
conditioning outlet, the outlet should be closed.
• Install the unit so that the monitor when opened up will not
block access to the hazard switch or other important controls.
• Do not install the unit (monitor) in locations which may be
subject to excessively low or high temperatures. (Otherwise the
unit may be deformed and the LCD may be damaged.)
Exposure to direct sunlight can also lead to high temperatures
and should be avoided.
Selecting the installation location
1
Set the ignition key to OFF or remove it.
2
Place the units in their intended mounting
locations to check the cable length and monitor
installation conditions.
Frequency select switch
The AM (FM) tuning interval is factory-set to the 9 k (50 k)
position. If the frequency allocation system of your country is
based on 10 kHz (200 kHz) interval, set the switch on the bottom
of the unit to the 10 k (200 k) position before making connections.
FM 200k AM 10k
FM 50k AM 9k
Frequency select switch
6
Cluster panel dimensions
25.5
17.3
6.2
22.5
25
33.6 44.7 55.7 20.6
18
171
175.4
Installation procedure precautions
• Perform the installation carefully. Dropping the unit or
otherwise subjecting it to strong impact or force may deform
the chassis, resulting in failure of the monitor loading
mechanism or other defects.
T/N
T/N T/N
TT
T
N
N
N
•To allow for proper opening and closing of the monitor, there
must be a clearance of at least 147 mm between the closest
position of the shift lever and the mounting surface for the unit.
• In some cases, the shift lever may touch the monitor when
moved to a certain position. Make sure that there is no
obstruction to driving operations.
• When installing this unit together with other car audio
equipment (single DIN slot size) in a stacked configuration,
install the Media Center main unit on top.
Shift lever
At least 147 mm
from mounting
surface
Note
If the installation dimensions shown at
right are not observed, the monitor may
not open up smoothly. If this happens,
check the installation once more and
modify the cluster panel where the
dimension requirements are not met. For
some car models, a separately available
mounting kit may be required.
(For details, please consult your dealer.)
Center line
Unit: mm
7
Installation procedure
Mounting example
When installing this unit, be sure to close the monitor of the unit.
If the monitor is opened while installing and given too much
force, it may cause a malfunction.
1
2
3
4
q;
6
9
9
6
9
6
7
qa
qs
qd
q;
Bend these claws outward
for a tight fit, if necessary.
Dashboard
182 mm
53 mm
Fire wall
8
CSX-V58MP
(optional)
Nissan cars
Align the brackets of the factory-installed car stereo with the
mounting holes marked “N” on the side of the Media Center
main unit, and use the supplied pan-head screws 6 to fasten the
brackets.
* Be sure to use only the supplied pan-head screws 6 for
installation. If any other screws are used, make sure they
conform to the requirements shown below.
Using longer screws can cause internal damage to the unit.
5 mm
6 mm
Damage can also occur if the screws are used directly on the
unit without the brackets of the factory-installed car stereo.
Screws of factory-
installed car stereo
bracket
Bracket of
factory-installed
car stereo
6
Toyota cars (illustration shows an example for a Toyota car)
Align the brackets of the factory-installed car stereo with the
mounting holes marked “T” on the side of the Media Center main
unit, and use the supplied screws to fasten the brackets. For
Toyota cars, the supplied screws 6 should be used.
Note
• Do not press the front panel buttons of
the unit during installation and do not
apply strong force.
• Do not place any objects on top of the
unit.
When removing front panel plate
Front panel
plate 4
Do not throw away the front panel plate,
since it will be needed when you change
the car you install the unit.
For details, see “Removing the Front
Panel Plate”. (page 17).
Screws of factory-
installed car stereo
bracket
Bracket of
factory-installed
car stereo
XAV-77
XAV-77
CSX-V58MP
(optional)
6
9
Note
• Ensure that the mounting surface is
clean.
• Do not install the connection box
– in locations subject to high
temperatures
– in locations subject to direct sunlight,
warm air from heater outlets, or
other locations that can get hot.
• When attaching the hook-and-loop
fastener to the bottom of the connection
box, do not cover the model name plate
in the center.
Hook-and-loop
fastener 8
Hook-and-loop
fastener 8
On installation surface
Installing the connection box XA-114
Cut off the required length of hook-and-loop fastener 8 and fix
the connection box 1 on the carpet or similar.
Use of connectors
Insert until the connector clicks into
place. To remove, press here and pull out.
Main unit/connection
box interconnect 3
Hooking up the connection box
Refer also to the section “3 Car Systems Connections” (page 14 -
15).
Insert 3 until a click is heard.
To Media center
Main unit
10
Refer also to the section “3 Car Systems Connections” (page 14 -
15).
Insert 2 and 3 until a click is heard.
2 Main Unit Connections
Use of connectors
Insert until the connector clicks into
place. To remove, press here and pull
out.
To connection
box
Main unit/
connection box
interconnect 3
Power supply leads 2
(for main unit)
Insert until the connector clicks into
place. To remove, press here and pull
out.
11
Connection Example
For details, see the section “3 Car Systems Connections” (page 14 - 15). Be sure to refer also to the
documentation for all other components in the system.
Speaker connections
SUB WOOFER
OUT(MONO)
FRONT AUDIO
OUT
SUB WOOFER
OUT(MONO)
REAR AUDIO
OUT
Notes
• Be sure to connect the ground cord before connecting the amplifier.
• If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated.
Media Center
main unit
Active subwoofer
(optional)
Front speakers
(optional)
Rear speakers
(optional)
Media Center
main unit
Active subwoofer
(optional)
Front speakers
(optional)
Rear speakers
(optional)
Amplifiers
(optional)
12
CONTROL(OUT)
OUTPUT VIDEO IN
INPUT1/2
INPUT
CONTROL
XAV
REAR MONITOR OUTPUT
Connection of separately available accessories
Items except the main unit and the connection box are optionally available.
With Sony bus system TV tuner unit
CONTROL(OUT)
CONTROL(IN)
INPUT1/2
OUTPUT VIDEO IN
INPUT
INPUT
CONTROL
XAV
REAR MONITOR OUTPUT
Without TV tuner unit
Tip
For connecting two or more CD/MD changers, the source selector is necessary.
Media Center
main unit
TV tuner unit
CD/MD changer, or
Source selector
Monitor
Connection box
(supplied)
DVD player
Media Center
main unit
CD/MD/DVD changer,or
Souce selecter
Connection box
(supplied)
DVD player
Monitor
13
Using the tap
Attach and fix the tap securely as illustrated.
Connecting the parking cord
Be sure to connect the parking cord (Light green) to the parking
brake switch cord. The mounting position of the parking brake
switch cord depends on your car. Refer to the system connection
diagram below and consult your car dealer or your nearest Sony
dealer for further details.
Parking brake
warning light
Media Center
main unit
Parking brake
switch cord
Parking cord
(Light green)
Parking brake switch
Body earth
Parking brake switch cord
Foot brake type
Parking brake switch cord
Hand brake type
Tap 5
Connecting Information
For details, see the section “3 Car Systems Connections” (next page).
Notes
• Be sure to connect the power input
cord after all other cords have been
connected.
• If the parking brake switch cord is too
thin, connect the parking cord to the
parking brake switch cord directly
without using the tap.
Parking brake switch
cord
Tap 5
Parking cord
(Light green)
Battery power
14
3 Car Systems Connections
Refer also to the documentation for all other components in the system.
Also see “Connecting Information” on page 13.
• Components listed here except for supplied accessories are available separately. When connecting such
components, be sure to also refer to their documentation.
For specifications and other information on separately available components, contact your dealer.
Prevention of accidents caused by short-circuits
To prevent the risk of accidents caused by short-circuits, connect the power supply leads (red and yellow)
only after all other wiring has been completed, and only with the ignition key in the OFF position.
Otherwise, accidental short-circuiting can lead to electric shock and to serious damage.
When a fuse has blown, check the wiring and locate the cause of the problem before replacing the fuse.
When replacing the fuse, be sure to use only a fuse of the same rating (ampere rating). Using a different
fuse or bridging the contacts with wire is highly dangerous and can lead to serious damage.
Make sure to connect all of the following leads.
Otherwise there is a risk of electric shock, damage to the equipment, or malfunction.
• Connect light green lead to parking brake switch lead of car.
• Connect yellow lead to battery power supply of car.
• Connect red lead to accessory power supply of car.
• Connect black lead to metal point on car chassis.
* Do not mix up the yellow and red leads, as this will cause the memory contents to be lost.
Observe the following precautions.
Otherwise there is a risk of electric shock, damage to the equipment, or malfunction.
• Cover unused connectors with electrician’s tape to prevent accidental contact.
• Route FM/AM antenna cable, bus cable, RCA interconnects, and power supply leads as far apart from
each other as possible, to prevent noise interference.
• Always grasp the connector and do not pull the cable when disconnecting the bus cable or other cables.
Otherwise the cable may become detached.
Note
Install the TV antennas away from the FM/AM antenna.
Notes on the control and power supply leads
• The power antenna control lead (blue) supplies +12 V DC when turn on the tuner.
• When your car has built-in FM/AM antenna in the rear/side glass, connect the power antenna control
lead (blue) or the accessory power input lead (red) to the power terminal of the existing antenna
booster. For details, consult your dealer.
•A power antenna without relay box cannot be used with this unit.
Memory hold connection
When the yellow power input lead is connected, power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid
its damage.
• Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers
with those of the left speaker.
• Do not connect the ground lead of this unit to the negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
•To avoid a malfunction, do not use the built-in speaker wires installed in your car if the unit shares a
common negative (–) lead for the right and left speakers.
• Do not connect the unit’s speaker cords to each other.
15
INPUT
CONTROL
XAV
To the +12 V power terminal which is
energized at all times
*2
*1Be sure to connect the black ground lead to it first.
*2First connect the black ground lead, then connect the orange/white striped, yellow and red power input
leads.
*3When your car has built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power
supply leads” (previous page).
*4This connection is only for amplifiers. Connecting any other system may damage the unit.
*5It is not necessary to connect this lead if there is no power antenna or antenna booster, or with a manually-
operated telescopic antenna.
Note on the accessory power input lead (red)
If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times.
Bus cable (supplied with TV tuner unit)
TV tuner unit
(optional)
Connection
box 1
Main unit/
connection box
interconnect 3
Front speakers
(optional)
Rear speakers
(optional)
Active subwoofer
(optional)
Media Center
main unit
Power
supply leads
2 (for main
unit)
Yellow (0.25 m)
Red (0.25 m)
Orange/white (0.25 m)
Light blue (0.25 m)
Fuse (10 A)
Light green (2 m)
Parking brake switch lead of car
Tap 5
To the +12 V power terminal which is
energized in the accessory position of
the ignition key switch
*2*3
To a car’s illumination signal
*2
To ATT (the interface cable of a car
telephone)
To a metal surface of the car
*1
Blue/white (0.25 m)
Blue (0.25 m)
To AMP REMOTE IN of an optional
power amplifier
*4
To the power antenna control lead or
power supply lead of antenna booster
amplifier
*3*5
Rotary
Commander
RM-X4S
(optional)
Front speakers
(optional)
Rear speakers
(optional)
White
White/black
Gray
Gray/black
Green
Green/black
Purple
Purple/black
RCA interconnects
(optional)
RCA interconnects
(optional)
RCA interconnects
(optional)
Left
Right
Left
Right
From car
antenna
Black (0.45 m)
Max. supply current 0.3 A
Max. supply current 0.1 A
Amplifiers
(optional)
RCA interconnects
(supplied with TV
tuner unit)
16
Note
To avoid the possibility of damage, you
should not use a needle or push the
button too strongly.
4 After Installation and Connections
1
Start the car’s engine.
2
Verify that the brake lights, other lights, horn, turn
indicators, and all other electrical parts operate
normally.
3
Use a ball-point pen or similar to push the Reset
button on the unit.
When you press the Reset button, the system becomes
operative.
Reset button
Warning when installing in a car without ACC
(accessory) position on the ignition key switch
Be sure to hold down OFF on the unit to turn off the clock
display after turning off the engine.
When you press OFF only momentarily, the clock display does
not turn off and this causes battery wear.
17
B
B
A
1
Pull the lower side of the front
panel plate forward (arrow A), to
open a gap between the front panel
plate and the body of the unit.
2
Insert a coin or similar thin item in
this gap, and twist to remove the
front panel plate.
Be careful not to damage the unit.
Remove in the order left-to-right.
3
Spreading the lower side of the
front panel plate outward (arrow
B), detach the plate from the body.
Removing the Front Panel Plate
Front panel plate 4
Be careful not to pull off the plastic parts.
Insert a coin and twist to remove
the front panel plate.
To remove the front panel plate from the unit, use the following procedure.
Note
Be careful not to pull off the plastic parts
attached to the lower side of the unit
together with the front panel plate.
2
•
•
•
•
•
•
•
3
1
2
3
4
4
q;
12 3
4
*1
56
78 9
q; qa qs
×2
×2
2.5 m
×4
qd
qf
qg
*2
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
