ページを読み込んでいます...
ページを読み込んでいます...
– 3 –
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
– JAPANESE –
Model information table
Model
HDR-
CX550
HDR-
CX550E
HDR-
CX550V
HDR-
CX550VE
HDR-
XR550
HDR-
XR550E
HDR-
XR550V
HDR-
XR550VE
Destination E,KR
NE, E , CH,
HK, JE
US, CND,
J
AEP, AUS E, KR, JE
NE, E, CH,
HK, JE
US, CND,
J
AEP, AUS
Color system NTSC PAL NTSC PAL NTSC PAL NTSC PAL
GPS
××○○××○○
Hard Disk Drive
××××○○○○
Intenal Memory
○○○○××××
Control switch
block(PS34600)
○○○○××××
Control switch
block(PS34700)
××××○○○○
FP-1202 BOARD
××××○○○○
FP-1203 BOARD
○○○○××××
FP-1204 BOARD
××○○××○○
• Abbreviation
AUS : Australian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
J : Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
– 4 –
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Unleaded solder
Boards requiring use of unleaded solder are printed with the leadfree
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are “pinched”
or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to
the customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and recommend
their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270°C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
0
– ENGLISH – – JAPANESE –
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
1-6
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
PPP:
PITCH G
1
YYY:
YAW G
2
PPP
YYY
MM-094 BOARD (SIDE B)
SE9201
– JAPANESE –
11
C13
C:31:11
wa ws
qj qk
1-7
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
– JAPANESE –
VC-592 BOARD (A SIDE)
IC5501
R5512
R5513
R5527
1-8
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
– JAPANESE –
1-9
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
– JAPANESE –
HDR-CX550 (E )
Part No. Description
A-1771-844-A CABINET BM(CX550E23)
HDR-CX550 (KR )
Part No. Description
A-1771-847-A CABINET BM(CX550KR2)
HDR-CX550E (NE )
Part No. Description
A-1771-853-A CABINET BM(CX550ECEL)
HDR-CX550E (E, HK, JE )
Part No. Description
A-1771-851-A CABINET BM(CX550EE34)
HDR-CX550E (CH )
Part No. Description
A-1771-854-A CABINET BM(CX550ECN2)
HDR-CX550V (US )
Part No. Description
A-1771-842-A CABINET BM(CX550VU2)
HDR-CX550V (CND )
Part No. Description
A-1771-843-A CABINET BM(CX550VCA2)
HDR-CX550V (J )
Part No. Description
A-1771-831-A CABINET BM(CX550VJ1)
HDR-CX550VE (AEP )
Part No. Description
A-1771-849-A CABINET BM(CX550VECEN)
HDR-CX550VE (AUS )
Part No. Description
A-1771-850-A CABINET BM(CX550VEAU2)
HDR-XR550 (E )
Part No. Description
A-1771-860-A CABINET BM(XR550E23)
HDR-XR550 (KR )
A-1771-861-A CABINET BM(XR550KR2)
Part No. Description
HDR-XR550 (JE )
Part No. Description
A-1771-862-A CABINET BM(XR550JE3)
HDR-XR550E (NE )
Part No. Description
A-1771-867-A CABINET BM(XR550ECEL)
HDR-XR550E (E )
Part No. Description
A-1771-865-A CABINET BM(XR550EE34)
HDR-XR550VE (AUS )
A-1771-864-A CABINET BM(XR550VEAU2)
HDR-XR550V (US )
A-1771-858-A CABINET BM(XR550VU2)
HDR-XR550V (CND )
A-1771-859-A CABINET BM(XR550VCA2)
HDR-XR550VE (AEP )
A-1771-863-A CABINET BM(XR550VECEN)
HDR-XR550V (J )
HDR-XR550E (CH )
A-1771-856-A CABINET BM(XR550VJ1)
Part No. Description
Part No. Description
Part No. DescriptionPart No. Description
Part No. Description
Part No. Description
A-1771-868-A CABINET BM(XR550ECN2)
HDR-XR550E (HK, JE )
Part No. Description
A-1771-866-A CABINET BM(XR550EHK1)
1-10E
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
OFF
ON
GPS
OFF
ON
GPS
– JAPANESE –
HDR-CX550V (J ) HDR-XR550V (J )
*
*
*
*
HDR-CX550V (US ) HDR-XR550V (US )
*
*
*
*
HDR-CX550 (KR ) HDR-XR550 (KR )
*
*
*
*
CX550V/CX550VE XR550V/XR550VE
2-1
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
AC- DIS-
Link
ACCESSORIESDISCHARGING OF THE CHARGING CAPACITOR ASSEMBLY
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original
one.
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not sup-
plied.
• Due to standardization, replacements in the parts list may be different from the parts
specified in the diagrams or the components used on the set.
• CAPACITORS:
uF: μF
• COILS
uH: μH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: μ, for example:
uA...: μA... , uPA... , μPA... ,
uPB... , μPB... , μPC... , μPC... ,
uPD..., μPD...
(JAPANESE)
*
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
The components identified by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
0 0
When indicating parts by reference
number,please include the board name.
• Abbreviation
AUS : Australian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
J : Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
Right View
Left View
Front View
Bottom View
Top View
Back View
View Position
XR550/XR550E/XR550V/XR550VE
XR550V/XR550VE
CX550/CX550E/CX550V/CX550VE
CX550V/CX550VE
4 Cabinet (BM)
7 Hinge Cover (R)
qd Shoe Cover Section
• FP-1210 Flexible Board
• FP-1211 Flexible Board
q; Cabinet F Section
• FP-1196 Flexible Board
8 Cabinet F Section
• FP-1196 Flexible Board
5 Cabinet L Assy
qa GP346 Assy
1 Cabinet (G) Assy
2 Heat Sink G
3 HDD
9 Cabinet Top Assy
8 Cabinet (R) Section
[Disassembly]
[Exploded View]
• Cabinet (R) Section
• CK-222 Board
• LCD Section
• PD-408 Board
• FP-1208 Flexible Board
qf Main Board Section
[Disassembly]
[Exploded View]
• Main Board Section
• VC-592 Board
• DD-329 Board
• ST-230 Board
• FP-1195 Flexible Board
• FP-1198 Flexible Board
• FP-1200 Flexible Board
• FP-1202 Flexible Board
• FP-1205 Flexible Board
• FP-1209 Flexible Board
• Lens Section
• CM-103 Board
• MA-464 Board
• FP-1204 Flexible Board
• FP-1206 Flexible Board
qs BT/EVF Section
[Disassembly]
[Exploded View]
• MM-094 Board
• FP-1197 Flexible Board
• FP-1199 Flexible Board
• FP-1207 Flexible Board
2 Cabinet (BM)
3 Hinge Cover (R)
qd Shoe Cover Section
• FP-1211 Flexible Board
6 Cabinet L Assy
9 GP346 Assy
1 Cabinet (G) Assy
5 Cabinet Top Assy
4 Cabinet (R) Section
[Disassembly]
[Exploded View]
• Cabinet (R) Section
• CK-222 Board
• LCD Section
• PD-408 Board
• FP-1208 Flexible Board
qf Main Board Section
[Disassembly]
[Exploded View]
• Main Board Section
• VC-592 Board
• DD-329 Board
• ST-230 Board
• FP-1195 Flexible Board
• FP-1198 Flexible Board
• FP-1200 Flexible Board
• FP-1203 Flexible Board
• FP-1205 Flexible Board
• FP-1209 Flexible Board
• Lens Section
• CM-103 Board
• MA-464 Board
• FP-1204 Flexible Board
• FP-1206 Flexible Board
qs BT/EVF Section
[Disassembly]
[Exploded View]
• MM-094 Board
• FP-1197 Flexible Board
• FP-1199 Flexible Board
• FP-1207 Flexible Board
Note:There aren’t q;, qa procedures.
• FP-1210 Flexible Board
2-2
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
The charging capacitor (C5012) of the ST-230 board is charged
up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
– ENGLISH – – JAPANESE –
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked
of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, don’t press down at wire of con-
nector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
DISCHARGING OF THE ST-230 BOARD'S CHARGING CAPACITOR (C5012)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Wrap insulating tape.
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
Be careful not to touch the metal plate
with the shot jig.
R:1 k
Ω
/1 W
(Part code: 1-215-869-11)
ST-230
C5012
ST-230 Board
ST-230
R:1 kΩ / 1 W
1-215-869-11
C5012
ST-230 Board
2-3
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION-1
(XR550/XR550E/XR550V/XR550VE)
Refer to page 2-4 about CX550/CX550E/CX550V/CX550VE
ns: not supplied
Ref. No. Part No. Description
Ref. No. Part No. Description
1 X-2547-054-1 CABINET G (347) ASSY
2 2-664-928-41 BELT, GRIP
3 4-177-960-01 HEAT SINK G (347)
4 4-179-888-01 HD DAMPER SHEET
5 4-177-969-01 GASKET (10X10X4)
6 4-181-717-01 SHEET, HD GUARD
7 1-840-187-21 HDD (MK2431GAH-240GB) (XR550/XR550E)
7 A-1708-620-A SERVICE (240G_OPAL), HDD (XR550V/XR550VE)
(Note 1)
8 3-298-143-01 DAMPER (2), 08STYLE (Note 2)
9 X-2547-052-1 CABINET L (347) ASSY
10 2-589-376-01 FOOT (395), RUBBER
11 (Note 3) CABINET(BM)
#2 2-635-562-31 SCREW (M1.7)
#11 3-078-890-11 SCREW, TAPPING
#12 3-080-204-21 SCREW, TAPPING, P2
#158 2-660-401-51 SCREW (M1.7), NEW TRU-STAR, P2
1. Remove to numerical order (1 to 6) in the left figure.
DISASSEMBLY
8
(Note 2)
8
(Note 2)
10
4
4 11
(Note 3)
3 7
(Note 1)
Overall Section-2
(See page 2-5)
ns
ns
#12
ns
#11
#158
#2
#2
#2
#2
#2
#11
1 1
2 3
2
6
5 9
6
5
ns
1-1
1-2
(Claw)
(Claw)
(Claw)
1 #2 X 2 → Remove the Grip Belt (1-1) → Slide the Cabinet (G) Assy (1-2)
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
Note
#2
Bottom View Back View
#2
2 #11 X 1 → #158 X 2
#158
#11
Left View
5 #12 X 1 → #2 X 6
#2
#2
#12
Left View Bottom View
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
4.0
1.7
Note 2: In case of attaching, turn concave
portion to the main body side.
Main body
Concave Portion
Note 2
Note 1: Do not factory check HDD in which Map Data is installed (XR550V/
XR550VE). The map data is erased when the factory check is done.
Note 1:
Note 3: Refer to page 1-4 “Precaution on replacing the Cabinet (BM)” when chang-
ing the Cabinet (BM).
Note 3:
4 #2 X 5
#2
Bottom View
DISCHARGING OF THE CHARGING CAPACITOR
6
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
5.0
1.7
#158: M1.7 X 5.0
(Red)
2-660-401-51
Refer to page 2-4 about CX550/CX550E/CX550V/CX550VE
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
2-8
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
2-1-6. MAIN BOARD SECTION
ns: not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
* 251 4-177-966-01 INSULATING SHEET (VC)
252 A-1765-177-A DD-329 BOARD, COMPLETE (SERVICE)
(CX550/CX550E) (Note 1,2)
252 A-1765-179-A DD-329 BOARD, COMPLETE (SERVICE)
(XR550/XR550E) (Note 1,2)
252 A-1765-396-A DD-329 BOARD, COMPLETE (SERVICE)
(CX550V/CX550VE) (Note 1,2)
252 A-1765-398-A DD-329 BOARD, COMPLETE (SERVICE)
(XR550V/XR550VE) (Note 1,2)
* 253 4-177-967-01 INSULATING SHEET (DD)
* 254 4-177-949-01 VC FRAME
255 1-880-387-11 FP-1205 FLEXIBLE BOARD
256 4-177-962-01 SHEET (A), RADIATION
257 A-1765-296-A VC-592 BOARD, COMPLETE (SERVICE)
258 A-1765-109-A FP-1198 FLEXIBLE BOARD, COMPLETE
259 4-177-964-01 SHEET (B), SHIELD
260 4-177-961-01 SHEET (B), RADIATION
261 4-181-949-01 SHEET (L2), SHIELD
(CX550V/CX550VE/XR550V/XR550VE)
262 1-880-384-11 FP-1202 FLEXIBLE BOARD
(XR550/XR550E/XR550V/XR550VE)
263 4-177-963-01 SHEET (A), SHIELD
(XR550V/XR550VE)
264 1-880-385-11 FP-1203 FLEXIBLE BOARD
(CX550/CX550E/CX550V/CX550VE)
* 265 4-177-951-01 ST FRAME
266 1-880-391-11 FP-1209 BOARD
267 A-1765-129-A ST-230 BOARD, COMPLETE
268 A-1765-110-A FP-1200 FLEXIBLE BOARD, COMPLETE
269 A-1765-108-A FP-1195 FLEXIBLE BOARD, COMPLETE
* 270 4-177-952-01 PLATE (H), FIXED
* 271 4-177-955-01 HOLDER (HU), TERMINAL
* 272 4-177-954-01 HOLDER (HO), TERMINAL
*C5012 1-116-460-11 CAP, ELECT 37uF 315V
#2 2-635-562-31 SCREW (M1.7)
#3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2
#12 3-080-204-21 SCREW, TAPPING, P2
#14 2-599-475-11 SCREW (M1.7)
ST-230
VC-592
DD-329
XR550/XR550E
XR550V/XR550VE
CX550V/CX550VE
XR550V/XR550VE
XR550V/XR550VE
CX550/CX550E
CX550V/CX550VE
A
B
C
A
B
C
C
Lens Section
(See page 2-9)
#2
#3
#3
#14
#3
#14
#12
#14
#14
#12
C5012
ns
ns
#2
#14
#14
#14
267
268
270
269
271
272
266
265
262
264
261
260
263
259
258
251
252
(Note 1,2)
257
256
254
251
253
255
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#3: M1.7 X 2.5
(Red)
2-660-401-01
2.5
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
Note
Note 1: When replacing the DD-329 board, start the Adjust Manual
in the Adjust Station and refer to the “INTERNAL MEMORY
ADJUSTMENTS”.
Note 1:
#14: M1.7 X 2.5
(Silver)
2-599-475-11
2.5
1.7
Note 2: Do not factory check DD-329 board in which Map Data is
installed (CX550V/CX550VE).
The map data is erased when the factory check is done.
Note 2:
2-9
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
2-1-7. LENS SECTION
ns: not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
301 A-1765-130-A MA-464 BOARD, COMPLETE
(CX550V/CX550VE/XR550V/XR550VE)
301 A-1765-131-A MA-464 BOARD, COMPLETE
(CX550/CX550E/XR550/XR550E)
302 1-880-386-11 FP-1204 FLEXIBLE BOARD
(CX550V/CX550VE/XR550V/XR550VE)
* 303 4-178-003-01 FRAME (L), LENS
304 A-1733-302-A LSV-1390A (SERVICE)
305 1-856-033-21 OPTICAL FILTERBLOCK (OFB-03-52)
306 3-216-044-01 RUBBER (1270), SEAL
307 A-1733-301-A CMOS BLOCK ASSY (1390)
(including CM-103 complete board, IC6804 (CMOS
imager)) (Note 1)
* 308 4-135-726-01 SHEET (CM), RADIATION (Note 2)
309 1-880-388-11 FP-1206 FLEXIBLE BOARD
* 310 4-178-006-01 SHEET (5X13)
* 311 4-178-005-01 SHEET (C), SHIELD
* 312 4-177-966-01 INSULATING SHEET (VC)
#11 3-078-890-11 SCREW, TAPPING
#12 3-080-204-21 SCREW, TAPPING, P2
#14 2-599-475-11 SCREW (M1.7)
Screw
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
#14: M1.7 X 2.5
(Silver)
2-599-475-11
2.5
1.7
Note
CX550V/CX550VE
XR550V/XR550VE
#11
#14
#14
#14
ns
ns
#11
#14
#11
#12
308
(Note 2)
306
307
(including CM-103 complete board,
IC6804 (CMOS imager))
(Note 1)
305
309
310
303
301
302
304
311
312
Note 1: Be sure to read “Precautions for Replacement of Imager”
on page 6-1 when changing the imager.
Note 1:
Note 2: The Radiation Sheet CM when peeling off once, so that it
cannot be reused
Note 2:
2-10
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
2-1-8. BT/EVF SECTION
ns: not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
* 351 4-178-009-01 PLATE, TERMINAL HOLDER FIXED
* 352 4-178-008-01 RETAINER, TERMINAL
353 A-1765-111-A FP-1197 FLEXIBLE BOARD, COMPLETE
354 X-2547-056-1 HOLDER (346) ASSY, TERMINAL
(CX550/CX550E/CX550V/CX550VE)
354 X-2547-057-1 HOLDER (347) ASSY, TERMINAL
(XR550/XR550E/XR550V/XR550VE)
355 1-880-389-11 FP-1207 FLEXIBLE BOARD
356 A-1765-107-A FP-1199 FLEXIBLE BOARD, COMPLETE
357 X-2547-060-1 EYE CUP ASSY
* 359 4-178-033-01 VF RETAINER
360 X-2547-055-1 BT PANEL ASSY
* 361 4-178-007-01 BT FRAME
362 A-1765-294-A MM-094 BOARD, COMPLETE (SERVICE)
BH001 1-780-064-21 BATTERY TERMINAL BOARD
*BH7301 1-251-928-21 SOCKET, BATTERY (Note)
BT7301 1-756-134-12 BATTERY, STORAGE, LITHIUM (Note)
J001 1-815-792-11 CONNECTOR, DC-IN (7.2V)
LCD902 1-811-013-11 LCD MODULE (FL0906)
#3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2
#11 3-078-890-11 SCREW, TAPPING
#12 3-080-204-21 SCREW, TAPPING, P2
MM-094
#12
#11
#3
#11
#12
LCD902
BH001
360
357
356
354
353
351
352
355
BH7301
(Note)
: BT7301 (LITHIUM STORAGE BATTERY)
Board on the mount position.
(See page 6-30 of LEVEL3)
ns
BT7301
(Note)
J001
359
362
361
Screw
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
Note
Note: Replace the battery holder (BH7301) together when replac-
ing the lithium storage battery (BT7301) on the MM-094
board.
(The battery holder removed once cannot be used
again.)
When mounting these parts, mount new battery holder first
and attach new lithium storage battery next.
Note:
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
:
#3: M1.7 X 2.5
(Red)
2-660-401-01
2.5
1.7
ページを読み込んでいます...
2-12
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
2-1-10. LCD SECTION
ns: not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
451 4-178-058-01 P CABINET C (CX550/CX550E/CX550V/CX550VE)
451 4-178-058-11 P CABINET C (XR550/XR550E/XR550V/XR550VE)
* 452 4-178-061-01 MOLD, LCD INNER
453 A-1765-173-A PD-408 BOARD, COMPLETE
454 4-178-060-01 LCD FRAME
* 455 4-178-006-01 SHEET (5X13)
456 4-182-483-01 CUSHION, LCD (346)
457 4-178-059-01 P CABINET M
* 458 4-178-062-01 COVER (O), HINGE
459 1-880-390-11 FP-1208 FLEXIBLE BOARD (Note 2)
* 460 4-167-146-01 CLAMP, FLEXIBLE (346)
461 X-2547-062-1 HINGE (346) ASSY
462 1-471-504-11 MAGNET (ND5X3.5X2.4-B) (Note 1)
* 463 4-178-063-01 COVER (U), HINGE
LCD901 A-1763-666-A LCD BLOCK ASSY (SERVICE) (Note 3)
#2 2-635-562-31 SCREW (M1.7)
#14 2-599-475-11 SCREW (M1.7)
Screw
Note
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#14: M1.7 X 2.5
(Silver)
2-599-475-11
2.5
1.7
Note 1:
Put the marking side
together on the position
of figure when
you install the magnet.
Marking
PD-408
459
(Note 2)
458
460
463
451
452
453
455
455
455
457
456
LCD901
(Note 3)
ns
(Claw)
#2
462
(Note 1)
#2
461
#14
#14
454
Note 2:
Note 3:
LCD Frame
P Cabinet M
Push the LCD Frame from the side in the back,
and check whether there is between LCD unit
and the P cabinet M the space.
Check whether LCD unit is at the center of the
window frame.
When LCD unit shifts from the center of the
window frameInstall the LCD unit again, and align
the LCD unit to the center of the window frame
(align the upper and lower, right and left, even).
LCD Unit
Window Frame
(Don't be stranded Pcabinet M on a LCD unit.)
Note 3:
Note2:
Refer to “Assembly-1: The methode of attachment of
FP-1208 Flexible Board” when installing .
2-13
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
• EXCEPT J MODEL
Checking supplied accessories.
AC Adaptor
(AC-L200C/L200D)
* Compatible in
L200C and L200D.
1-487-150-51
Conversion (2P) Adaptor
1-569-007-12 (E:NTSC, JE)
Component A/V cable
1-834-646-11
A/V connecting cable
1-823-156-61
Wireless Remote Commander
(RMT-835)
1-479-275-51
Rechargeable battery pack
(NP-FV50)
(Note)
USB cable
1-835-993-31
Power cord (Mains lead)
1-832-121-41 (CH)
1-832-169-41 (HK)
1-833-892-41 (KR)
1-834-482-21 (AEP, NE, E:PAL)
1-834-484-31 (US, CND)
1-834-852-11 (E:NTSC)
1-835-983-11 (AUS)
1-836-251-11 (JE)
0
0
0
0
0
0
0
0
0
0
Operating Guide
HDR-CX500/CX550V/XR550/XR550V
(Only for destination Japanese model)
4-170-538-11 (ENGLISH, SPANISH)
4-170-538-21 (FRENCH)
4-170-538-31 (PORTUGUESE)
4-170-538-41 (TRADITIONAL CHINESE)
4-170-538-51 (KOREAN)
Operating Guide
HDR-CX500E/CX550VE/XR550E/XR550VE
(Only for destination Japanese model)
4-170-539-11 (ENGLISH)
4-170-539-21 (FRENCH, GERMAN, ITALIAN, DUTCH)
4-170-539-31 (SPANISH, PORTUGUESE, TURKISH, GREEK)
4-170-539-41 (CZECH, HUNGARIAN, SLOVAK, POLISH)
4-170-539-51 (SWEDISH, DANISH, FINNISH, ROMANIAN)
4-170-539-61 (RUSSIAN, UKRAINIAN)
4-170-539-71 (TRADITIONAL CHINESE)
4-170-539-81 (SIMPLIFIED CHINESE) (E:PAL, JE)
4-170-539-91 (ARABIC, PERSIAN)
4-170-541-11 (SIMPLIFIED CHINESE) (CH)
Handycam Handbook (PDF)
CD-ROM "Handycam
Application Software"
-
"PMB" (software) including
"PMB Guide"
-
"Handycam Handbook"
(PDF)
4-170-533-01
4-170-536-71 (FINNISH)
4-170-536-81 (ROMANIAN)
4-170-536-91 (RUSSIAN)
4-170-537-11 (UKRAINIAN)
4-170-537-21 (TRADITIONAL CHINESE)
4-170-537-31 (SIMPLIFIED CHINESE)
4-170-537-41 (ARABIC)
4-170-537-51 (PERSIAN)
4-170-537-61 (MALAY)
4-170-537-71 (INDONESIAN)
4-170-537-81 (THAI)
The CD-ROM supplied contains all of language version of
the Instruction Manual in pdf (
Handycam Handbook.pdf) for printing.
(Only for destination Japanese model)
The printed matter is not supplied. If required,
please order it with the part number below.
4-170-534-11 (ENGLISH)
4-170-534-21 (FRENCH)
4-170-534-31 (SPANISH)
4-170-534-41 (PORTUGUESE)
4-170-534-51 (TRADITIONAL CHINESE)
4-170-534-61 (KOREAN)
HDR-CX500/CX550V/XR550/XR550V
4-170-535-11 (ENGLISH)
4-170-535-21 (FRENCH)
4-170-535-31 (GERMAN)
4-170-535-41 (ITALIAN)
4-170-535-51 (DUTCH)
4-170-535-61 (SPANISH)
4-170-535-71 (PORTUGUESE)
4-170-535-81 (TURKISH)
4-170-535-91 (GREEK)
4-170-536-11 (CZECH)
4-170-536-21 (HUNGARIAN)
4-170-536-31 (SLOVAK)
4-170-536-41 (POLISH)
4-170-536-51 (SWEDISH)
4-170-536-61 (DANISH)
HDR-CX500E/CX550VE/XR550E/XR550VE
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Note: This item is supplied with the unit as an accessory,
but is not prepared as a service part.
• J MODEL
(AC-L200C/L200D)
L200C L200D
0 1-487-150-51
A/V
1-823-156-61
USB
1-835-993-31
D A/V
1-834-646-21
(RMT-835)
1-479-275-51
(NP-FV50)
(Note 1)
CD-ROM Handycam
Application Software
-
PMB ( PMB )
-
(PDF) (Note 2)
4-170-533-01
0
Note 1 :
Note 2:
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
6-1
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
6. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS
– ENGLISH – – JAPANESE –
For Schematic Diagrams
• All capacitors are in μF unless otherwise noted. pF : μ
μF. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum capaci-
tor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example C541 L452
22U 10UH
TA A 2520
Kinds of capacitor External dimensions (mm)
Case size
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
• Signal name
XEDIT → EDIT PB/XREC → PB/REC
•
: non flammable resistor
•
: fusible resistor
• : panel designation
•
: B+ Line
•
: B– Line
•
: IN/OUT direction of (+, –) B LINE.
•
: adjustment for repair.
For Printed Wiring Boards
•
: Uses unleaded solder.
•
: Circuit board
: Flexible board
Pattern from the side which enables seeing.
: pattern of the rear side
(The other layers’ patterns are not indicated)
• Through hole is omitted.
• There are a few cases that the part printed on diagram
isn’t mounted in this model.
•
: panel designation
• Chip parts.
Transistor Diode
Precautions for Replacement of Imager
• If the imager has been replaced, carry out all the adjustments
for the camera section.
• As the imager may be damaged by static electricity from its
structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strong light.
The components identified by mark 0
or dotted line with mark 0 are critical
for safety.
Replace only with part number specified.
Les composants identifiés par une mar-
que 0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
When indicating parts by reference num-
ber, please include the board name.
21
3
21
3
21
3
345
21
123
654
EB
C
31
5
2
46
123
654
31
5
2
46
123
54
43
12
312
45
534
12
14
23
46
2
5
31
12
43
14
23
21
3
21
3
21
3
345
21
123
654
EB
C
31
5
2
46
123
654
31
5
2
46
123
54
43
12
312
45
534
12
14
23
46
2
5
31
12
43
14
23
0 0
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS
(In addition to this, the necessary note is printed in each block)
Please refer to LEVEL 3 about the SCHEMATIC DIAGRAMS and
PRINTED WIRING BOARDS of CM-114, MM-088 and VC-588.
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/
