Screening Eagle Profometer PM8500 クイックスタートガイド

PM8500

Quick Start Guide & Product Certicates

Kurzanleitung & Produktzertikate

Guide de Prise en Main & Certicats de produits

Guida Breve & Certicati di prodotto

Guía de Inicio Rápido & Certicados del producto

Guia de Início Rápido & Certicados do produto

КрКраткое руководство & Сертификаты продукта

クイックスタートガイド & 製品証明書

快速入门指南 & 产品证书

빠른 시작 안내서 & 제품 인증서

Included / inbegriffen / inclus/

incluso / incluido / incluído /

включены / 含まれる / 包括 /

포함 된

Profometer PM8500 – Standard Kit

A Carrying case

B PM8500 Sensor

C Universal Holder for Sensor

D Chest harness for iPad

E USB-C to USB-A cable

F Battery charger + 2 AA

batteries

G 25-meter cable roll with

clamp

H REL100: Rod Electrode

with spare parts

I Copper sulphate, 250g

J 1.5m Cable Rod – Sensor

K Large sponge

L Quick Start Guide

AC

D

B

E

G

K L

IH

F

J

Included / inbegriffen / inclus/

incluso / incluido / incluído /

включены / 含まれる / 包括 /

포함 된

Profometer WEL100: One Wheel Kit

A One wheel electrode

with cables

B Carbon ber telescopic rod

C Copper sulphate, 250g

D Citric acid, 250g

E Tool kit

F Water container, 1.25l

AC

D

B

EF

Included / inbegriffen / inclus/

incluso / incluido / incluído /

включены / 含まれる / 包括 /

포함 된

Profometer WEL400 – Four Wheel Kit

A 150 to 250mm variable

distance four-wheel elec-

trode with cables

B Carbon ber telescopic rod

C Copper sulphate, 250g

D Citric acid, 250g

E Tool kit

F Carrying case

A

C D

B

E

F

Use only rechargeable AA batteries in the charger.

Verwenden Sie im Ladegerät nur wiederauadbare

AA-Batterien.

Utilisez uniquement des piles AA rechargeables dans

le chargeur.

Utilizzare solo batterie AA ricaricabili nel

caricabatterie.

Utilice únicamente pilas AA recargables en el

cargador.

Use apenas pilhas AA recarregáveis no carregador.

Используйте в зарядном устройстве только

перезаряжаемые батарейки типа АА.

充電器には充電式単三電池のみを使用してください。

充电器中只能使用可充电 AA 电池。

충전기에는 충전식 AA 배터리만 사용하십시오.

a

>2h

PM8500 Sensor

Battery charge and installation

1

a

b

c

PM8500 Sensor

Connecting the rod electrode

C1 (bigger)

Short cable B1 (smaller)

D1 (medium)

Connect the clamp of the ground cable (A) with the

exposed rebar

Connect the ground cable (B) to the interface box

using B1 plug

Connect the rod cable (C) to the interface box using

C1 plug and to the electrode using C2 plug

C

B

A

B1

C1

C2

1

PM8500 Sensor

Connecting the one wheel electrode

BD

C

A

a

b

c

Connect the clamp of the ground cable (A) with the

exposed rebar

Connect the ground cable (B) to the sensor using B1 plug

Connect the potential cable (C) and the encoder cable

(D) to the sensor using C1 and D1 plugs

B1

C1 D1

C1 (bigger) B1 (smaller)

D1 (medium)

1

PM8500 Sensor

Connecting the four wheel electrode

B

A

a

b

c

Connect the clamp of the ground cable (A) with the

exposed rebar

Connect the ground cable (B) to the sensor using B1 plug

Connect the potential cable (C) and the encoder cable (D)

to the sensor using C1 and D1 plugs

C1 (bigger) B1 (smaller)

D1 (medium)

DC

B1

C1 D1

2

PM8500 RodElectrode

Filling therodelectrode with Copper Sulphate

a

b

c

Remove the cap with the wooden plug and soak it intowater for about an hour to allow the wood to saturate and swell.

Prepare the saturated solution by mixing40 units by weight of coppersulphate with 100 units by weight of distilled water.

Add an additionalteaspoon of copper sulphate crystals into the electrode.

The electrode should be lled as completely as possible with aminimumof airin the compartment.

2

PM8500 WheelElectrodes

Filling thewheelelectrodes with Copper Sulphate

a

b

c

d

e

The wooden plug (A) is not intended to be removed.Immerse the wheel in water for an hour to allow the water to soak into theplug.

Only the wheels should be immersed, therefore, please remove themfrom the legs before doing it.

The felt hoops (B) and the felt hoop connector must be saturated beforemeasuring. In normal use (with water and cupper solution),

the thin felt ison the wooden spigot side (A).

Prepare the saturated solution by mixing40 units by weight of coppersulphate with 100 units by weight of distilledwater. Fill in the

cupper tank removing the plug (C). Add an additionalteaspoon of copper sulphate crystals into theelectrode.

Theelectrodeshouldbelledascompletelyaspossiblewithaminimumofairinthecompartment.

Fill in the water container with water. To do so you need to remove the water plug (D).

The water should be dripping out slowly from the water tank throughoutthe 1mm nozzle (E). The bike valve on the opposite side

should provide a high pressure;if water is dripping out too fast, please apply some pressureblowing the bike valve with your mouth.

B

A E DC

3

A

PM8500 Universal holder

How to mount the interface box on the harness

aUse the inner clamp (A) of the universal holder to attach it to the iPad harness or your belt

4

C

PM8500 Universal holder

How to mount the interface box on the telescopic rod

a

b

Connect the round support (B) of the universal holder to the

telescopic rod and attach it using the rubber band (C).

Recommendation: Use the holder rubber band as strain relief

for the cable-reel-cable.

B

5

A

PM8500 Telescopic rod

How to mount the telescopic rod on the one wheel and four wheel electrode

a

b

Connect the telescopic rod with the one wheel / four-wheel connector (A)

Move the indented wheel clockwise to join both parts

6

PM8500 Rod Electrode Foams

How to replace the foam of the rod electrode

a

b

Remove the foam (A) from the rod electrode if it is broken or overused

Stick the new foam (B) into the same position. Please use only a small amount of glue

A

B

7

PM8500 Four wheel variable distance

How to change the distance between the wheels (limited from 150mm to 250mm)

Unscrew the collars (A) – wheels 2, 3 and 4. Wheel 1 is always xed

Slide the wheel legs (B) to the desired position

For the 150mm version, mount the wheels as described in the position marks (C) (all wheels are facing to the xed wheel)

For the 250mm version, mount the wheels as described in the position marks (D) (the right two wheels must be turned to face the right side)

Screw the collars (A) to x the wheels at the desired position

Any other distance from 150mm to 250mm can be selected

a

c

e

b

d

D

f

250mm version

Fixed

wheel

Wheels facing left Wheels facing right

B B

C

150mm version

Wheels facing left

A

PM8500 Four wheel variable distance

How to change the distance between the wheels (limited from 150mm to 250mm)

250mm version

200mm version

150mm version

7

200mm version

150mm version

PM8500 Four wheel variable distance

How to change the distance between the wheels (limited from 150mm to 250mm)

7

8

PM8500 Start device

Turning on / off the device

For product usage information, please refer

to the Profometer PM8500 documentation.

It is available for download on:

www.screeningeagle.com/en/products/profometer-pm8500

Medium press (3 sec)

LED: Green solid

QR

CODE

ページが読み込まれています...

Screening Eagle Profometer PM8500 クイックスタートガイド

Screening Eagle Profometer PM8500 クイックスタートガイド

他の言語で

関連論文

その他のドキュメント