STCT1860
English 3
繁體中文 11
18
2
A
B
E
F
C
D
3
G
H
I
4
ENGLISH
CORDLESS JIG SAW
STCT1860
Technical Data
STCT1860
Input power V 18
No-load speed/rated
speed min
-1
0-2500
Stroke length mm 19
Max depth of cut
Wood mm 55
Steel mm 8
Aluminium mm 20
Weight kg 2.6
charger 90588647(KR) 90600163(TW)
Input power V AC 220 110
Output Voltage VDC 18 18
Current A 2 2
Approx. charge time min 60-120 60-120
Battery STBL182L STBL184L
Voltage VDC 18 18
Capacity Ah 2.0 4.0
Type Li-Ion Li-Ion
Your Stanley cordless jig saw has been designed
for sawing wood, plastics and sheet metal. This
tool is intended for professional and private, non
professional users.
Safety instructions
General power tool safety warnings
WARNING! Read all safety warnings
and all instructions. Failure to follow the
warnings and instructions listed below
may result in electric shock, re and/or
serious injury.
Save all warnings and instructions for future
reference. The term “power tool” in all of the
warnings listed below refers to your mains
operated (corded) power tool or battery operated
(cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
ammable liquids, gases or dust. Power
tools create sparks which may ignite the dust or
fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools. Unmodied plugs
and matching outlets will reduce risk of electric
shock.
b. Avoid body contact with earthed or
grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an
increased risk of electric shock if your body is
earthed or grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric
shock.
e. When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f. If operating a power tool in a damp location
is unavoidable, use a residual current
device (RCD) protected supply. Use of an
RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the inuence of drugs,
alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b. Use personal protective equipment. Always
wear eye protection. Protective equipment
5
ENGLISH
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the
switch is in the off-position before
connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with your nger on the
switch or energising power tools that have the
switch on invites accidents.
d. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e. Do not overreach. Keep proper footing and
balance at all times. This enables better
control of the power tool in unexpected
situations.
f. Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in
moving parts.
g. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b. Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is
dangerous and must be repaired.
c. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of
children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e. Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tools operation. If
damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g. Use the power tool, accessories and tool
bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
5. Battery tool use and care
a) Recharge only with the charger specied by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of
re when used with another battery pack.
b) Use power tools only with specically
designated battery packs. Use of any other
battery packs may create a risk of injury and
re.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small
metal objects, that can make a connection
from one terminal to another. Shorting the
battery terminals together may cause burns or
a re.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, ush with water. If
liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
6. Service
a) Have your power tool serviced by a qualied
repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional power tool safety warnings
Warning! Additional safety warnings for hand-
held saws
u Hold power tool by insulated gripping
6
ENGLISH
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring. Cutting accessory contacting a
“live” wire may make exposed metal parts of the
power tool “live” and could give the operator an
electric shock.
u Use clamps or another practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand or
against your body leaves it unstable and may
lead to loss of control.
u Keep hands away from cutting area. Never
reach underneath the work piece any reason.
Do not insert ngers or thumb into the vicinity of
the reciprocating blade and blade clamp. Do
not stabilize the saw by gripping the shoe.
u Keep blades sharp. Dull or damaged blades
may cause the saw to swerve or stall under
pressure. Always use the appropriate type of
saw blade for the workpiece material and type
of cut.
u When cutting pipe or conduit, make sure
that they are free from water, electrical
wiring, etc.
u Do not touch the workpiece or the blade
immediately after operating the tool. They
can become very hot.
u Be aware of hidden hazards, before cutting
into walls, oors or ceilings, check for the
location of wiring and pipes.
u The blade will continue to move after
releasing the switch. Always switch the tool
off and wait for the saw blade to come to a
complete standstill before putting the tool down.
@ Warning! The vibration emission value
during actual use of the power tool can differ from
the declared value depending on the ways in which
the tool is used. The vibration level may increase
above the level stated.
u The intended use is described in this
instruction manual. The use of any accessory
or attachment or performance of any operation
with this tool other than those recommended in
this instruction manual may present a risk of
personal injury and/or damage to property.
Safety of others
u This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
u Children should be supervised to ensure that
they do not play with the appliance.
Residual risks
Additional residual risks may arise when using the
tool which may not be included in the enclosed
safety warnings. These risks can arise from mis-
use, prolonged use etc.Even with the application of
the relevant safety regulations and the implemen-
tation of safety devices, certain residual risks can
not be avoided. These include:
u Injuries caused by touching any rotating/moving
parts.
u Injuries caused when changing any parts,
blades or accessories.
u Injuries caused by prolonged use of a tool.
When using any tool for prolonged periods
ensure you take regular breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust
developed when using your tool (example:-
working with wood, especially oak, beech and
MDF.)
Labels on tool
The following pictograms are shown on the tool:
:
Warning! To reduce the risk of injury, the
user must read the instruction manual.
Additional safety instructions for batteries
and chargers
Batteries
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not store in locations where the temperature
may exceed 40 °C.
u Charge only at ambient temperatures between
10 °C and 40 °C.
u Charge only using the charger provided with the
tool.
u When disposing of batteries, follow the
instructions given in the section “Protecting the
environment”.
p
Do not attempt to charge damaged batteries.
7
ENGLISH
Chargers
u Use your Stanley charger only to charge the
battery in the tool with which it was supplied.
Other batteries could burst, causing personal
injury and damage.
u Never attempt to charge non-rechargeable
batteries.
u Have defective cords replaced immediately.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
$
The charger is intended for indoor use only.
+
Read the instruction manual before use.
Electrical safety
#
Your charger is double insulated; therefore
no earth wire is required. Always check
that the mains voltage corresponds to the
voltage on the rating plate. Never attempt
to replace the charger unit with a regular
mains plug.
u If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised
Stanley Service Centre in order to avoid a
hazard.
Features
This tool includes some or all of the following
features.
1. Variable speed trigger switch
2. Lock-off button
3. Saw blade locking lever
4. Blade clamp
5. Shoe plate
6. Cutting action button
Fig. A
8. Battery charger
9. Charging indicator
Assembly
Warning! Before assembly, remove the battery
from the tool and make sure that the saw blade
has stopped. Used saw blades may be hot.
Fitting and removing the saw blade (g. B)
u Hold the saw blade (10) with the teeth facing
forward.
u Lift the saw blade locking lever (3) upwards.
u Insert the shank of the blade fully into the blade
clamp (4) as far as it will go.
u Release the lever.
u To remove the saw blade (10), lift the saw blade
locking lever (3) upwards and pull the blade out.
Fitting and removing the battery (g. C)
u To t the battery (7), line it up with the
receptacle on the tool. Slide the battery into the
receptacle and push until the battery snaps into
place.
u To remove the battery, push the release buttons
(11) while at the same time pulling the battery
out of the receptacle.
Use
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Never use the tool when the saw shoe is
loose or removed.
Charging the battery (g. A)
The battery needs to be charged before rst use
and whenever
it fails to produce sufcient power on jobs that
were easily done before. The battery may become
warm while charging; this is normal and does not
indicate a problem.
Warning! Do not charge the battery at ambient
temperatures below 10 °C or above 40 °C. Recom-
mended charging temperature: approx. 24 °C.
Note: The charger will not charge a battery if
the cell temperature is below approximately 10
°C or above 40 °C.The battery should be left
in the charger and the charger will begin to
charge automatically when the cell temperature
warms up or cools down.
u To charge the battery (7), insert it into the
charger (8). The battery will only t into the
charger in one way. Do not force. Be sure that
the battery is fully seated in the charger.
u Plug in the charger and switch on at the mains.
The charging indicator (9) will blink.The charge
is complete when the charging indicator (9)
switches to continuously on. The charger and
8
ENGLISH
the battery can be left connected indenitely.
The LED will switch on as the charger
occasionally tops up the battery charge.
u Charge discharged batteries within 1 week.
Battery life will be greatly diminished if stored in
a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connect-
ed with the LED glowing indenitely. The charger
will keep the battery pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery,
the charging indicator (9) will ash red at a fast
rate. Proceed as follows:
u Re-insert the battery (7).
u If the charging indicators continues ashing red
at a fast rate, use a different battery to
determine if the charging process works
properly.
u If the replaced battery charges correctly, the
original battery is defective and should be
returned to a service centre for recycling.
u If the new battery gives the same indication as
the original battery, take the charger to be
tested at an authorised services centre.
Note: It may take as long as 30 minutes to
determine that the battery is defective. If the
battery is too hot or too cold, the LED will
alternately blink red, fast and slow, one ash at
each speed and repeat.
Switching on and off (g. D & E)
u To switch on, slide the lock off switch (2) to the
left then pull and hold the variable speed trigger
switch (1).
u To switch off, release the trigger switch (1).
Warning! Do not switch the tool on or off while
under load.
Warning! Always slide the lock off switch (2) to
the right, the locked position when the tool is not
in use.
Variable speed control
The variable speed on/off switch offers a choice of
speeds for greatly improved cutting rates in various
materials.
u The speed is determined by the amount the
trigger switch (1) is pulled.
Bevel cutting (g. F, G & H)
The shoe plate can be set to a left or right bevel
angle of 45°.
To set the bevel angle:
u Loosen the shoe retaining bolt (12) with the hex
key provided to unlock the shoe plate (5).
u Slide the shoe plate (5) forward to release it
from the 0° detent.
u Rotate the shoe plate to the desired bevel angle
(g. G).
u Slide the shoe plate backwards to engage the
left or right detent.
u Tighten the shoe retaining bolt (12) with the hex
key provided to lock the shoe plate (5) in the
required position.
Note: The shoe can be beveled to the left or to the
right and has detents at 45°.
Cutting action (g. I)
This jig saw is equipped with three cutting actions,
two orbital and one straight. Orbital action has a
more aggressive blade motion and is designed for
cutting in soft materials like wood or plastic. Orbital
action provides a faster cut, but with a less smooth
cut across the material. In orbital action, the blade
moves forward during the cutting stroke in addition
to the up and down motion.
Warning! Metal or hardwoods should never be cut
in orbital action.
u Slide the cutting action button (6) between the
three cutting positions: 0, 1 and 2.
u Position 0 is for straight cutting.
u Positions 1 and 2 are for orbital cutting.
u The aggressiveness of the cut increases as the
lever is adjusted from one to two, with two
being the most aggressive cut.
Sawing
u Always hold the tool with both hands.
u Let the blade run freely for a few seconds
before starting the cut.
u Apply only a gentle pressure to the tool while
performing the cut.
u If possible, work with the shoe plate (5) pressed
against the workpiece. This will improve tool
control and reduce tool vibration, as well as
prevent the blade from being damaged.
Hints for optimum use
General
u Use a high speed for wood, a medium speed
for aluminium and PVC and a low speed for
metals other than aluminium.
9
ENGLISH
Sawing laminates
As the saw blade cuts on the upward stroke,
splintering may occur on the surface closest to the
shoe plate.
u Use a ne-tooth saw blade.
u Saw from the back surface of the workpiece.
u To minimise splintering, clamp a piece of scrap
wood or hardboard to both sides of the
workpiece and saw through this sandwich.
Sawing metal
Be aware that sawing metal takes much more time
than sawing wood.
u Use a saw blade suitable for sawing metal. Use
a ne-tooth saw blade for ferrous metals and a
coarser saw blade for non-ferrous metals.
u When cutting thin sheet metal, clamp a piece of
scrap wood to the back surface of the
workpiece and cut through this sandwich.
u Spread a lm of oil along the intended line of
cut.
Accessories
The performance of your tool depends on the ac-
cessory used.Stanley accessories are engineered
to high quality standards and designed to enhance
the performance of your tool. By using these ac-
cessories you will get the very best from your tool.
Blades
The saw will accept a blade up to 30 cm long.
Always use the shortest blade suitable for your
project but long enough to keep the blade cutting
through the material. Longer blades are more likely
to be bent or damaged during use. During opera-
tion some longer blades may vibrate or shake if the
saw is not kept in contact with the workpiece.
Maintenance
Your Stanley corded/cordless appliance/tool has
been designed to operate over a long period of
time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool
care and regular cleaning.
Warning! Before performing any maintenance on
corded/cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the
appliance/tool if the appliance/tool has a
separate battery pack.
u Or run the battery down completely if it is
integral and then switch off.
u Unplug the charger before cleaning it. Your
charger does not require any maintenance
apart from regular cleaning.
u Regularly clean the ventilation slots in your
appliance/tool/charger using a soft brush or dry
cloth.
u Regularly clean the motor housing using a
damp cloth. Do not use any abrasive or
solvent-based cleaner.
u Regularly open the chuck and tap it to remove
any dust from the interior (when tted).
Protecting the environment
Separate collection. This product must
not be disposed of with normal household
waste.
Should you nd one day that your Stanley product
needs replacement, or if it is of no further use to
you, do not dispose of it with household waste.
Make this product available for separate collection.
Separate collection of used products and
packaging allows materials to be recycled
and used again. Re-use of recycled mate-
rials helps prevent environmental pollution
and reduces the demand for raw materials.
Local regulations may provide for separate collec-
tion of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
Batteries
Z
Stanley batteries can be recharged many
times. At the end of their useful life,
discard batteries with due care for our
environment.
Service Information
Stanley offers a full network of company-owned
and authorized service locations throughout Asia.
All Stanley Service Centers are staffed with trained
personnel to provide customers with efcient
and reliable power tool service.Whether you
need technical advice, repair, or genuine factory
10
ENGLISH
replacement parts, contact the Stanley location
nearest to you.
Notes
u Stanley’s policy is one of continuous
improvement to our products and, as such, we
reserve the right tochange product
specications without prior notice.
u Standard equipment and accessories may vary
by country.
u Product specications may differ by country.
u Complete product range may not be available in
all countries. Contact your local Stanley dealers
for range availability.
11
18V
STCT1860
STCT1860
V 18
/
min
-1
0-2500
mm 19
mm 55
mm 8
mm 20
kg 2.6
90588647(KR) 90600163(TW)
V AC 220 110
V DC 18 18
A 2 2
min 60-120 60-120
STBL182L STBL184L
V DC 18 18
Ah 2.0 4.0
Sta nley
/
1.
a.
b.
c.
2.
a.
b.
c.
d.
e.
f.
(RCD) RCD
3.
a.
b.
12
c. /
d.
e.
f.
g.
4.
a.
b.
c.
/
d.
e.
f.
g.
5.
a)
b)
c)
d)
6.
a)
u
u
13
u
u
u
u
u
u
u
/
u
u
u /
u
u
u
(MDF)
:
u
u 40 °C
u 10 °C 40 °C
u
u
p
u Stanley
u
u
u
u
u
14
$
+
#
u Stanley
1.
2.
3.
4.
5.
6.
A
8.
9.
B
u (10)
u (3)
u (4)
u
u (10) (3)
C
u (7)
u (11)
A
10 °C 4 0 °C
24 °C
10 ºC 40 ºC
u (7) (8)
u (9)
(9)
LED
u 1
15
LED
(9)
u (7)
u
u
u
30
LED
D E
u (2)
(1)
u (1)
(2)
u (1)
FG H
45 °
u (12)
(5)
u (5) 0 °
u G
u
u (12)
(5)
45 °
I
u (6)
01 2
u 0
u 12
u 1 2
2
u
u
u
u (5)
u PVC
16
u
u
u
u
u
u
Stanley
30 cm
Stanley / /
/
u /
u /
/
u
u
u / /
u
u
Stanley
Z
Stanley
Stanley
Stanley
Stanley
17
u Stanley
u /
u
u /
Stanley
137
02-29994633
18
STCT1860
STCT1860
V 18
/
-1
0-2500
mm 19
mm 55
mm 8
mm 20
kg 2.6
90588647(KR) 90600163(TW)
V AC 220 110
V DC 18 18
A 2 2
60-120 60-120
STBL182L STBL184L
V DC 18 18
Ah 2.0 4.0
,
.
.
!
.
, /
.
. "
"
() ()
.
1.
a. .
.
b. ,
.
c.
.
.
2.
a.
.
. ( )
.
.
b. , ,
.
,
.
c.
.
.
d. .
. , ,
.
e.
.
.
f.
(RCD)
. RCD
.
3.
a.
.
19
, ,
.
.
b. .
. ,
,
.
c. . /
.
.
d.
.
.
e. .
.
.
f. .
. ,
. ,
.
g.
,
.
.
4.
a. .
.
.
b. /
.
.
c.
/
.
.
d.
,
.
.
e. .
,
.
.
.
f.
.
.
g. ,
,
.
.
5.
a)
.
.
.
.
c) , ,
, , ,
.
.
d)
.
.
.
.
6.
a)
.
.
20
!
u
. " "
" "
.
u
.
.
u .
.
.
.
u .
.
.
u ,
.
u
. .
u . ,
.
u .
.
@ !
.
.
u
.
.
u ,
( )
.
.
u
.
.
,
.
.
.
u .
u , .
u .
.
u .
u
(: , ,
MDF ).
.
:
! ,
.
u
.
u .
u 40 °C
.
u 10 °C - 40 °C
.
u
.
u " "
.
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
