DeWalt DCD701M ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル
DCD701M
B
Copyright DeWALT
English 3
简体中文 11
1
1
2
4
5
6
8
9
7
1
2
1
2
14
3
10
XXXX XX XX
13
Fig. A
A
Fig. B
B
2
9
3
8
12
11
10
Fig. E
E
Fig. F
F
Fig. C
C
Fig. D
D
ENGLISH
3
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
thesesymbols.
DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
seriousinjury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
seriousinjury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderateinjury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
propertydamage.
Denotes risk of electricshock.
Denotes risk offire.
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough
product development and innovation make DeWALT one of the
most reliable partners for professional power toolusers.
Technical Data
DCD701M
Voltage V
DC
12
Battery type Li-Ion
Power output W 250
No-load speed
1st gear
2nd gear
min
-1
min
-1
0–425
0–1500
Max. Torque (hard/soft) Nm 57.5/25.5
Chuck capacity mm 10
Maximum
drilling
capacity
Wood
Metal
mm
mm
20
10
Weight (without battery pack) kg 0.87
SUB-COMPACT DRILL/DRIVER
DCD701M
V
Ah
kg
DCB104 DCB107 DCB112 DCB113 DCB115 DCB118 DCB132 DCB119
DCB122 12 2.0 0.22 30 90 60 50 30 X 30 60
DCB124 12 3.0 0.25 45 140 90 70 45 45 45 90
DCB125 12 1.3 0.20 22 60 40 30 22 X 22 40
DCB127 12 2.0 0.20 30 90 60 50 30 X 30 60
4
ENGLISH
Safety Instructions for All Operations
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory or
the fastener may contact hidden wiring. Cutting accessory
or the fastener contacting a “live” wire may make exposed
metal parts of the power tool “live” and could give the operator
an electricshock.
Safety Instructions When Using Long
DrillBits
Never operate at higher speed than the maximum
speed rating of the drill bit. At higher speeds, the bit is likely
to bend if allowed to rotate freely without contacting the
workpiece, resulting in personalinjury.
Always start drilling at low speed and with the bit tip
in contact with the workpiece. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting the
workpiece, resulting in personalinjury.
Apply pressure only in direct line with the bit and do not
apply excessive pressure. Bits can bend causing breakage or
loss of control, resulting in personalinjury.
Additional Safety Warnings for Drills
Use clamps or other practical way to secure and support
the workpiece to a stable platform. Holding the work by
hand or against your body is unstable and may lead to loss
ofcontrol.
Accessories and tool may get hot during operation. Wear
gloves when handling them if performing heat producing
applications such as drillingmetals.
Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be caught in
movingparts.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
Impairment ofhearing.
Risk of personal injury due to flyingparticles.
Risk of burns due to accessories becoming hot
duringoperation.
Risk of personal injury due to prolongeduse.
SAVE THESE INSTRUCTIONS
Chargers
DeWALT chargers require no adjustment and are designed to be
as easy as possible tooperate.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
your charger corresponds to that of yourmains.
Your DeWALT charger is double insulated in
accordance with IEC60335; therefore no earth wire
isrequired.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the
DeWALT
serviceorganisation.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1mm
2
; the maximum length
is30m.
When using a cable reel, always unwind the cablecompletely.
Important Safety Instructions for All Battery
Chargers
SAVE THESE INSTRUCTIONS: This manual contains important
safety and operating instructions for compatible battery
chargers (refer to TechnicalData).
Before using charger, read all instructions and cautionary
markings on charger, battery pack, and product using
batterypack.
WARNING: Shock hazard. Do not allow any liquid to get
inside charger. Electric shock mayresult.
WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA orless.
CAUTION: Burn hazard. To reduce the risk of injury,
charge only
DeWALT rechargeable batteries. Other types of
batteries may burst causing personal injury anddamage.
CAUTION: Children should be supervised to ensure that
they do not play with theappliance.
NOTICE: Under certain conditions, with the charger
plugged into the power supply, the exposed charging
contacts inside the charger can be shorted by foreign
material. Foreign materials of a conductive nature such
as, but not limited to, steel wool, aluminum foil or any
buildup of metallic particles should be kept away from
charger cavities. Always unplug the charger from the
power supply when there is no battery pack in the cavity.
Unplug charger before attempting to clean
DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual. The charger
and battery pack are specifically designed to worktogether.
These chargers are not intended for any uses other than
charging
DeWALT rechargeable batteries. Any other uses
may result in risk of fire, electric shock orelectrocution.
Do not expose charger to rain orsnow.
Pull by plug rather than cord when disconnecting
charger. This will reduce risk ofdamage to electric plug
andcord.
Make sure that cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage orstress.
5
ENGLISH
Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result in risk
of fire,electric shock, orelectrocution.
Do not place any object on top of charger or place
the charger on a soft surface that might block the
ventilation slots and result in excessive internal heat.
Place the charger in a position away from any heat source. The
charger is ventilated through slots in the top and the bottom
of thehousing.
Do not operate charger with damaged cord or plug—
have them replacedimmediately.
Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way. Take it
to an authorised servicecentre.
Do not disassemble charger; take it to an authorised
service centre when service or repair is required. Incorrect
reassembly may result in a risk of electric shock, electrocution
orfire.
In case of damaged power supply cord the supply cord must
be replaced immediately by the manufacturer, its service agent
or similar qualified person to prevent anyhazard.
Disconnect the charger from the outlet before
attempting any cleaning. This will reduce the risk of
electric shock. Removing the battery pack will not reduce
thisrisk.
NEVER attempt to connect two chargerstogether.
The charger is designed to operate on standard 220-
240V household electrical power. Do not attempt to
use it on any other voltage. This does not apply to the
vehicularcharger.
Charging a Battery (Fig. B)
1. Plug the charger into an appropriate outlet before inserting
batterypack.
2. Insert the battery pack
1
into the charger, making sure the
battery pack is fully seated in the charger. The red (charging)
light will blink repeatedly indicating that the charging
process hasstarted.
3. The completion of charge will be indicated by the red
light remaining ON continuously. The battery pack is fully
charged and may be used at this time or left in the charger.
To remove the battery pack from the charger, push the
battery release button
2
on the batterypack.
NOTE: To ensure maximum performance and life of lithium-ion
battery packs, charge the battery pack fully before firstuse.
Charger Operation
Refer to the indicators below for the charge status of the
batterypack.
Charge Indicators
Charging
Fully Charged
Hot/Cold Pack Delay*
* The red light will continue to blink, but a yellow indicator light
will be illuminated during this operation. Once the battery pack
has reached an appropriate temperature, the yellow light will
turn off and the charger will resume the chargingprocedure.
The compatible charger(s) will not charge a faulty battery pack.
The charger will indicate faulty battery by refusing tolight.
NOTE: This could also mean a problem with acharger.
If the charger indicates a problem, take the charger and battery
pack to be tested at an authorised servicecentre.
Hot/Cold Pack Delay
When the charger detects a battery pack that is too hot or too
cold, it automatically starts a Hot/Cold Pack Delay, suspending
charging until the battery pack has reached an appropriate
temperature. The charger then automatically switches to the
pack charging mode. This feature ensures maximum battery
packlife.
A cold battery pack will charge at a slower rate than a warm
battery pack. The battery pack will charge at that slower rate
throughout the entire charging cycle and will not return to
maximum charge rate even if the battery packwarms.
Electronic Protection System
XR Li-Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deepdischarge.
The tool will automatically turn off if the Electronic Protection
System engages. If this occurs, place the lithium-ion battery
pack on the charger until it is fullycharged.
Wall Mounting
These chargers are designed to be wall mountable or to sit
upright on a table or work surface. If wall mounting, locate the
charger within reach of an electrical outlet, and away from a
corner or other obstructions which may impede air flow. Use
the back of the charger as a template for the location of the
mounting screws on the wall. Mount the charger securely using
drywall screws (purchased separately) at least 25.4mm long
with a screw head diameter of 7–9mm, screwed into wood to
an optimal depth leaving approximately 5.5mm of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in theslots.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using a
cloth or soft non-metallic brush. Do not use water or any
cleaning solutions. Never let any liquid get inside the tool;
never immerse any part of the tool into aliquid.
Battery Packs
Important Safety Instructions for All Battery
Packs
When ordering replacement battery packs, be sure to include
catalogue number andvoltage.
6
ENGLISH
The battery pack is not fully charged out of the carton. Before
using the battery pack and charger, read the safety instructions
below. Then follow charging proceduresoutlined.
READ ALL INSTRUCTIONS
Do not charge or use battery in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Inserting or removing the battery from the charger may
ignite the dust orfumes.
Never force battery pack into charger. Do not modify
battery pack in any way to fit into a non-compatible
charger as battery pack may rupture causing serious
personalinjury.
Charge the battery packs only in
DeWALTchargers.
DO NOT splash or immerse in water or otherliquids.
Do not store or use the tool and battery pack in
locations where the temperature may reach or exceed
40 ˚C (104 ˚F) (such as outside sheds or metal buildings
insummer).
Do not incinerate the battery pack even if it is severely
damaged or is completely worn out. The battery pack can
explode in a fire. Toxic fumes and materials are created when
lithium-ion battery packs areburned.
If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If
battery liquid gets into the eye, rinse water over the open eye
for 15 minutes or until irritation ceases. If medical attention
is needed, the battery electrolyte is composed of a mixture of
liquid organic carbonates and lithiumsalts.
Contents of opened battery cells may cause respiratory
irritation. Provide fresh air. If symptoms persists, seek
medicalattention.
WARNING: Burn hazard. Battery liquid may be flammable
if exposed to spark orflame.
WARNING: Never attempt to open the battery pack for
any reason. If battery pack case is cracked or damaged,
do not insert into charger. Do not crush, drop or damage
battery pack. Do not use a battery pack or charger that
has received a sharp blow, been dropped, run over or
damaged in any way (i.e., pierced with a nail, hit with
a hammer, stepped on). Electric shock or electrocution
may result. Damaged battery packs should be returned to
service centre forrecycling.
WARNING: Fire hazard. Do not store or carry the
battery pack so that metal objects can contact
exposed battery terminals. For example, do not place
the battery pack in aprons, pockets, tool boxes, product kit
boxes, drawers, etc., with loose nails, screws, keys,etc.
CAUTION: When not in use, place tool on its side on
a stable surface where it will not cause a tripping
or falling hazard. Some tools with large battery packs
will stand upright on the battery pack but may be easily
knockedover.
Transportation
WARNING: Fire hazard. Transporting batteries can
possibly cause fire if the battery terminals inadvertently
come in contact with conductive materials. When
transporting batteries, make sure that the battery
terminals are protected and well insulated from materials
that could contact them and cause a shortcircuit.
NOTE: Lithium-ion batteries should not be put in
checkedbaggage.
DeWALT batteries comply with all applicable shipping
regulations as prescribed by industry and legal standards which
include UN Recommendations on the Transport of Dangerous
Goods; International Air Transport Association (IATA) Dangerous
Goods Regulations, International Maritime Dangerous Goods
(IMDG) Regulations, and the European Agreement Concerning
The International Carriage of Dangerous Goods by Road (ADR).
Lithium-ion cells and batteries have been tested to section 38.3
of the UN Recommendations on the Transport of Dangerous
Goods Manual of Tests andCriteria.
In most instances, shipping a
DeWALT battery pack will be
excepted from being classified as a fully regulated Class 9
Hazardous Material. In general, only shipments containing a
lithium-ion battery with an energy rating greater than 100 Watt
Hours (Wh) will require being shipped as fully regulated Class 9.
All lithium-ion batteries have the Watt Hour rating marked on
the pack. Furthermore, due to regulation complexities,
DeWALT
does not recommend air shipping lithium-ion battery packs
alone regardless of Watt Hour rating. Shipments of tools with
batteries (combo kits) can be air shipped as excepted if the Watt
Hour rating of the battery pack is no greater than 100Whr.
Regardless of whether a shipment is considered excepted
or fully regulated, it is the shipper's responsibility to consult
the latest regulations for packaging, labeling/marking and
documentationrequirements.
The information provided in this section of the manual is
provided in good faith and believed to be accurate at the time
the document was created. However, no warranty, expressed or
implied, is given. It is the buyer’s responsibility to ensure that its
activities comply with the applicableregulations.
Storage Recommendations
1. The best storage place is one that is cool and dry away
from direct sunlight and excess heat or cold. For optimum
battery performance and life, store battery packs at room
temperature when not inuse.
2. For long storage, it is recommended to store a fully charged
battery pack in a cool, dry place out of the charger for
optimalresults.
NOTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be recharged
beforeuse.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the labels
on the charger and the battery pack may show the following
pictographs:
7
ENGLISH
Read instruction manual beforeuse.
See Technical Data for chargingtime.
Do not probe with conductiveobjects.
Do not charge damaged batterypacks.
Do not expose to water.
Have defective cords replacedimmediately.
Charge only between 4 ˚C and 40 ˚C.
Only for indooruse.
Discard the battery pack with due care for
theenvironment.
Charge DeWALT battery packs only with designated
DeWALT chargers. Charging battery packs other
than the designated
DeWALT batteries with a
DeWALT charger may make them burst or lead to
other dangeroussituations.
Do not incinerate the batterypack.
Battery Type
The DCD701 operates on a 12 volt batterypack.
These battery packs may be used: DCB122, DCB124, DCB125,
DCB127. Refer to Technical Data for moreinformation.
Package Contents
The package contains:
1 Drill/driver
1 Charger
1 Belt hook (included with some models)
1 Li-Ion battery pack (C1, D1, L1 models)
2 Li-Ion battery packs (C2, D2, L2 models)
3 Li-Ion battery packs (C3, D3, L3 models)
1 Instruction manual
NOTE: Battery packs, chargers and kitboxes are not included
with N models. Battery packs and chargers are not included with
NTmodels.
NOTE: Trademarks and trade names are those of their
respectiveowners.
Check for damage to the tool, parts or accessories which may
have occurred duringtransport.
Take the time to thoroughly read and understand this manual
prior tooperation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual beforeuse.
Wear earprotection.
Wear eyeprotection.
Visible radiation. Do not stare intolight.
Date Code Position (Fig. A)
The date code
13
, which also includes the year of manufacture,
is printed into thehousing.
Example:
2019 XX XX
Year of Manufacture
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury couldresult.
1
Battery pack
2
Battery pack release button
3
Main handle
4
Variable speed trigger
5
Forward/reverse control button
6
Mode selection collar
7
Speed selector
8
Worklight
9
Chuck sleeve
10
Keyless chuck
Intended Use
This drill/driver is designed for professional drilling and
screwdrivingapplications.
DO NOT use under wet conditions or in the presence of
flammable liquids orgases.
This drill/driver is a professional powertool.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
withoutsupervision.
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.
8
ENGLISH
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can causeinjury.
WARNING: Use only DeWALT battery packs andchargers.
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
NOTE: Make sure your battery pack
1
is fullycharged.
To Install the Battery Pack into the Tool Handle
1. Align the battery pack
1
with the rails inside the tool’s
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap intoplace.
To Remove the Battery Pack from the Tool
1. Press the release button
2
and firmly pull the battery pack
out of the toolhandle.
2. Insert battery pack into the charger as described in the
charger section of thismanual.
Fuel Gauge Battery Packs (Fig. B)
Some DeWALT battery packs include a fuel gauge which
consists of three green LED lights that indicate the level of
charge remaining in the batterypack.
To actuate the fuel gauge, press and hold the fuel gauge
button
14
. A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to berecharged.
NOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-userapplication.
Belt Hook (Fig.C)
Optional Accessories
WARNING: To reduce the risk of serious personal
injury, DO NOT suspend tool overhead or suspend
objects from the belt hook. ONLY hang tool’s belt hook
from a workbelt.
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook issecure.
IMPORTANT: When attaching or replacing a belt hook, use only
the screw that is provided. Be sure to securely tighten thescrew.
A belt hook
11
can be be attached to either side of the tool
using only the screw
12
provided, to accommodate left- or
right-handed users. If the belt hook is not desired at all, it can be
removed from thetool.
To move the belt hook, remove the screw
12
that holds it in
place then reassemble on the opposite side. Be sure to securely
tighten thescrew.
Installing a Bit or Accessory into a
KeylessChuck (Fig.D)
WARNING: Do not attempt to tighten drill bits (or
any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck
and personal injury may result. Always lock off trigger
switch and disconnect tool from power source when
changingacces sories.
WARNING: Always ensure the bit is secure before starting
the tool. A loose bit may eject from tool causing possible
personalinjury.
Your tool features a keyless chuck
10
with one rotating sleeve
9
for one-handed operation of the chuck. To insert a drill bit or
other accessory, follow thesesteps.
1. Turn tool off and remove batterypack.
2. Grasp the black sleeve of the chuck with one hand
and use the other hand to secure the tool. Rotate the
sleeve counterclockwise far enough to accept the
desiredaccessory.
3. Insert the accessory about 19 mm into the chuck and
tighten securely by rotating the chuck sleeve clockwise with
one hand while holding the tool with the other. Your tool is
equipped with an automatic spindle lock mechanism. This
allows you to open and close the chuck with onehand.
Be sure to tighten chuck with one hand on the chuck sleeve and
one hand holding the tool for maximumtightness.
To release the accessory, repeat steps 1 and 2above.
Speed Selection (Fig.A)
The tool features two speed settings for greaterversatility.
NOTE: Do not change speeds when the tool is running.
Always allow the tool to come to a complete stop before
changingspeed.
1. To select speed 1 (high torque setting), turn the tool off and
permit it to stop. Slide the speed selector
7
back (away
from thechuck).
2. To select speed 2 (high speed setting), turn the tool off and
permit it to stop. Slide the speed selector
7
forward (toward
thechuck).
If the tool does not change speeds, confirm that the speed
selection switch is completely engaged in the forward or
backposition.
Mode Selection (Fig. A)
The mode selection collar
6
can be used to select the correct
operating mode depending upon the plannedapplication.
To select, rotate the collar until the desired symbol aligns with
thearrow.
Symbol Mode
Drilling
1–15 Screwdriving (higher number = greater torque)
9
ENGLISH
Variable Speed Trigger and Forward/Reverse
Control Button (Fig. A)
The drill is turned on and off by pulling and releasing the
variable speed trigger
4
. The farther the trigger is depressed,
the higher the speed of the drill. Your tool is equipped with
a brake. The chuck will stop as soon as the trigger switch is
fullyreleased.
A forward/reverse control button
5
determines the rotational
direction of the tool and also serves as a lock-offbutton.
To select forward rotation, release the trigger and depress
the forward/reverse control button on the right side of
thetool.
To select reverse, depress the forward/reverse control
button on the left side of thetool.
NOTE: The centre position of the control button locks the tool
in the off position. When changing the position of the control
button, be sure the trigger isreleased.
NOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
beavoided.
NOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start up. This is normal and
does not indicate aproblem.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicableregulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can causeinjury.
Proper Hand Position (Fig. E)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Proper hand position requires one hand on the main handle
3
and one hand on the batterypack.
Worklight (Fig.F)
There is a worklight
8
located on the foot of the tool. The
worklight is activated when the trigger switch is depressed.
When the trigger is released, the worklight will stay illuminated
for up to 20seconds.
NOTE: The worklight is for lighting the immediate work surface
and is not intended to be used as aflashlight.
Performing an Application (Fig.A)
WARNING: To reduce the risk of personal injury,
ALWAYS ensure workpiece is anchored or clampedfirmly.
WARNING: Always wait until the motor has come to
a complete standstill before changing the direction
ofrotation.
Prior to performing work:
Set the speed selector
7
. Refer to SpeedSelection.
Install the appropriate bit or accessory into the chuck. Refer
to Installing a Bit or Accessory into a KeylessChuck.
WARNING:
Do not use this tool to mix or pump easily combustible
or explosive fluids (benzine, alcohol,etc.).
Do not mix or stir flammable liquids
labeledaccordingly.
Screwdriving
Your tool has a clutch with adjustable torque for driving
and removing a wide array of fastener shapes and sizes. The
numbers on the mode selection collar
6
are used to set a
torque range for screwdriving. The higher the number on the
collar, the higher the torque and the larger the fastener which
can bedriven.
1. Turn the mode selection collar
6
to the desiredposition.
Refer to Mode Selection.
2. Pull the trigger switch applying pressure in a straight line
with the bit until the fastener is seated at the desired depth
in theworkpiece.
Recommendations for Screwdriving
Start with lower torque settings, then advance to higher
torque settings to avoid damage to the workpiece
orfastener.
Make some practice runs in scrap or on unseen areas of the
workpiece to determine the proper position of the mode
selectioncollar.
Drilling
1. Turn the mode selection collar
6
to the drillsymbol. Refer
to ModeSelection.
2. Place drill bit in contact with theworkpiece.
NOTE: Use sharp drill bitonly.
3. Pull the trigger applying pressure in a straight line with the
bit until it reaches the desireddepth.
WARNING: Drill may stall if overloaded causing a sudden
twist. Always expect the stall. Grip the drill firmly to control
the twisting action and avoidinjury.
4. Keep the motor running when pulling the bit back out of a
drilled hole to preventjamming.
Recommendations for Drilling
When drilling, always apply pressure in a straight line with
the bit, but do not push hard enough to stall the motor or
deflect thebit.
IF THE DRILL STALLS:
- RELEASE TRIGGER SWITCH IMMEDIATELY, remove
drill bit from work, and determine cause ofstalling.
10
ENGLISH
- DO NOT DEPRESS TRIGGER SWITCH ON AND OFF
IN AN ATTEMPT TO START A STALLED DRILL—THIS
CAN DAMAGE THEDRILL.
- To minimize stalling or breaking through the material,
reduce pressure on drill and ease the bit through the last
fractional part of thehole.
Large holes (7.9 mm to 12.7 mm) in steel can be made
easier if a pilot hole (4 mm to 4.8mm) is drilledfirst.
If drilling thin material or material that is prone to splinter,
use a wood “back-up” block to prevent damage to
theworkpiece.
MAINTENANCE
Your DeWALT power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regularcleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can causeinjury.
The charger and battery pack are notserviceable.
Lubrication
Your power tool requires no additionallubrication.
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by
DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DeWALT recommended
accessories should be used with thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
householdwaste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
Run the battery pack down completely, then remove it from
thetool.
Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed ofproperly.
11
简体中文
󵶎󰽥󰶦󳛓
3
󲕂󰷑󽴼󲔞󱌍󳉸󱙃
󰵵󱐪󲕂󰷑󳎾󸒤󰸬󱝑󳫼󲴌󳦪󷸳󵒹󰶛󸡿󵪑󲫟󷸽󰺬󶑉󸾔󷹁󳦦󳅜󱍄󼵼󲪈
󴎥󲼒󸑰󰹉󳫼󲴌
󱙮󹀘󽴼󷞎󵤚󲒹󱲉󶄓󲶊󱙮󹀘󲺕󱎄󼵼󲁶󳩔󰵷󱔉󰻅󸘚󱋞󼵼󲘝󲘌󶩞
󴄦󰹗󳃵󰶛󸡿󰼠󲕳
󷵪󱟈󽴼󷞎󵤚󲒹󱲉󴞷󱲉󵒹󱙮󹀘󲺕󱎄󼵼󲁶󳩔󰵷󱔉󰻅󸘚󱋞󼵼󱜴󶡋
󲘌󶩞󴄦󰹗󳃵󰶛󸡿󰼠󲕳
󷵪󵤚󽴼󷞎󵤚󲒹󱲉󴞷󱲉󱙮󹀘󲺕󱎄󼵼󲁶󳩔󰵷󱔉󰻅󸘚󱋞󼵼󱜴󶡋󲘌
󶩞󸎾󲫟󳃵󰶦󲫟󰼠󲕳
󴎥󲼒󽴼󷞎󵤚󲒹󱲉󰵷󴒎󱛻󰺄󸉨󰼠󲕳󵒹󲺕󱎄󼵼󲁶󳩔󰵷󱔉󰻅󸘚
󱋞󼵼󱜴󶡋󲘌󶩞󸀓󰹢󳌁󱿠
󷞎󵤚󲒹󱲉󷩙󵉐󹑦󹀘
󷞎󵤚󲒹󱲉󴦡󴧈󹑦󹀘
󲷿󱧑󽴹
󲼮󷹨󲹡󸓦󸀞
DeWALT
󲦩󱌩󱏫󱂷󱾵󲪄󵒹󰹢󱡸󲮔󱜅󱠥󱐰󳜞󶑒
󹞊󼵼
DeWALT
󲦻󶑒󳃮󰶺󰶂󰶍󵉐󱔔󲦩󱌩󵈾󳄫󳥓󱜴󹈒󵒹󱝗󰽳󰼒󰼷󰷔󰵨
󳆯󳦪󱛭󳚩
DCD701M
󵉐󱚔 󰼄󴶶
󵕭󴐩
10
8
󼵸󳥓󱿑
12
󼵹
󵉐󴋒󵾬󱴘 󸹋󵨍󲒪
󱔇󴽨󸏖󱐁 󵆳
250
󵭠󸏀󸎯󸔠
1
󳮔
2
󳮔
󸎯󱐕
󸎯󱐕
0–425
0–1500
󳥓󱿑󳆎󵜄󼵸󵞾󸎲󼵹
󴶌󵾜
57
5
25
5
󱿫󱿣󲙰󲘅
󴈘󵾜
10
󳥓󱿑
󸸃󲒱
󶡋󱔃
󳦡󳧟
󸢅󲚪
󴈘󵾜
󴈘󵾜
20
10
󸡿 󸢁󼵸 󰵷 󱞏 󵉐 󴋒 󶑇 󼵹 󱘫󱋙
0
87
󲳏󱴘󵉐󸸃󸁱󲒪
DCD701M
󰼄󴶶
󲔞󳞟
󱘫󱋙
DCB104 DCB107 DCB112 DCB113 DCB115 DCB118 DCB132 DCB119
DCB122 12 2
0 0
22 30 90 60 50 30 X 30 60
DCB124 12 3
0 0
25 45 140 90 70 45 45 45 90
DCB125 12 1
3 0
20 22 60 40 30 22 X 22 40
DCB127 12 2
0 0
20 30 90 60 50 30 X 30 60
12
简体中文
4
󵶎󰽥󰶦󳛓
󵉐󱔔󲦩󱌩󸔒󵈾󲔞󱌍󷵪󱟈
󷵪󱟈󽴹󸾔󷹁󹁦󵉐󱔔󲦩󱌩󳏀󰿙󵒹󳄿󳥤󲔞󱌍󷵪󱟈󷸺󳟉
󱱄󵤚󱠥󷨟󲕂󰵷󸗾󴮒󰻅󰵵󳄿󱐪󷸺󳟉󰼕󲘌󶩞󵉐󱐂󵗢󴦡󱠥
󳃵󰶛󸡿󰼠󲕳
󱁃󲒹󳄿󳥤󷵪󱟈󱠥󷸺󳟉󰷽󰻅󱾋󳫆󸾔
󷵪󱟈󰶦󵒹󳦪󷸳
󵉐󱔔󲦩󱌩
󳉸󲧒󵉐󹝯󱔔󼵸󳥤󶑂󼵹󵉐󱔔󲦩󱌩󳃵󵉐󴋒
󹝯 󱔔󼵸 󳝾 󶑂 󼵹󵉐 󱔔 󲦩 󱌩
a)
󲦩󰽳󱲟󱲒󵒹󲔞󱌍
1 )
󱁃󳉰󲦩󰽳󱲟󱲒󴕢󴏈󱠥󳟉󰹮󳧈󰸊󱠥󹺲󳢞󵒹󱲟󱲒󰼕󲮹󱜅
󰸳󳙧
2 )
󰵷󷦴󱲉󳟓󴳙󴾡󱺰󼵼󲁶󳥤󳟓󴱎󴓋󰽥󴉟󰽥󳃵󵿌󲘾󵒹󴾡󱺰󰵵
󳕽󰽳󵉐󱔔󲦩󱌩󵉐󱔔󲦩󱌩󰹢󵈱󵒹󴦡󶰅󰼕󴩀󴱎󵿌󲘾󳃵󴉟󰽥
3 )
󳕽󰽳󵉐󱔔󲦩󱌩󳞟󼵼󸑵󵨍󱋅󵱚󱠥󳜿󷨝󶙐󴎥󲼒󱔃󰵷󹃌󰶦󰼕󰾫
󰽺󱿠󱛢󲘇󲦩󱌩󵒹󳍾󱑗
b)
󵉐󴉟󲔞󱌍
1 )
󵉐󱔔󲦩󱌩󳏄󱿣󲳴󹏣󰵹󳏄󲫡󵕲󸞂󶑠󰵷󶡋󰻅󰻤󰽧󳜱󲮮󳙗󷠴
󳏄󱿣󹄾󳍺󱲒󵒹󵉐󱔔󲦩󱌩󰵷󶡋󰾫󵈾󰻤󰽧󸎯󳌄󳏄󱿣󳦣󶑒
󳙗󷠴󵒹󳏄󱿣󱠥󵕲󸞂󵒹󳏄󲫡󲘝󸿮󰽜󵉐󱐂󹑦󹀘
2 )
󸘚󱋞󰺄󰽥󳍺󷩙󳍺󱲒󷞎󹈘󼵼󲁶󵷘󸖥󳚕󴪛󴵚󱠥󱍻󵷳󲁶󳩔󰽺
󸉨󰽥󳍺󷩙󳍺󱲒󷞎󹈘󰼕󱻟󱔉󵉐󱐂󹑦󹀘
3 )
󰵷󲲥󲘝󵉐󱔔󲦩󱌩󳣑󹆫󱲉󹄎󰶦󳃵󴟑󴘫󴾡󱺰󰶦󴊑󸑴󱌇󵉐󱔔
󲦩󱌩󲘝󱻟󱔉󵉐󱐂󹑦󹀘
4 )
󰵷󲲥󴛞󵈾󸎲󶑂󶑠󰵷󶡋󵈾󸎲󶑂󳑦󸑙󳈙󱔔󵉐󱔔󲦩󱌩󳃵󳈭
󱐁󱌧󳏄󱿣󰾫󸎲󶑂󸑵󵨍󴪛󴙃󴍙󸹙󸐞󳃵󸑙󱔔󸛉󰻞󱜍󳌁
󳃵󶒣󶑘󵒹󸎲󶑂󰼕󱻟󱔉󵉐󱐂󹑦󹀘
5 )
󲰳󱲉󳄫󱾫󰾫󵈾󵉐󱔔󲦩󱌩󳞟󼵼󰾫󵈾󸓔󱝗󳄫󱾫󰾫󵈾󵒹󲮂󸻌󶑂
󸓔󱝗󳄫󱾫󰾫󵈾󵒹󵉐󶑂󲘝󸿮󰽜󵉐󱐂󹑦󹀘
6 )
󲁶󳩔󳝾󴎂󸘚󱋞󱲉󴟑󴘫󴾡󱺰󰵵󳕽󰽳󵉐󱔔󲦩󱌩󼵼󲪿󰾫󵈾󲨅󳥤
󱒦 󰽯 󵉐 󴐩 󷠴 󶔩󼵸
RCD
󼵹󱁃 󳇢 󵒹 󵉐 󴙃 󵒹󰾫󵈾󱜴󸿮󰽜
󵉐󱐂󹑦󹀘
c)
󰺄󸉨󲔞󱌍
1 )
󱁃󳉰󷵪󷨤󼵼󲰳󳕽󰽳󵉐󱔔󲦩󱌩󳞟󱌣󴎥󳄿󰺣󰸳󵒹󳕽󰽳󲪈󱁃󳉰
󴕢󸠁󲰳󰽺󲼮󱑍󵌖󱃃󼵼󳃵󱲉󳥤󶶌󴶠󸞋󶀶󳃵󴍜󵋬󱜀󲪿󳞟󼵼
󰵷󷦴󳕽󰽳󵉐󱔔󲦩󱌩󱲉󳕽󰽳󵉐󱔔󲦩󱌩󳞟󵚖󸾃󵒹󵋝󲵑󰼕󲘌
󶩞󰶛󸡿󰺄󸉨󰼠󲕳
2 )
󰾫󵈾󰶢󰺄󸿉󳇢󷠴󶔩󲄥󶑋󰾇󳄦󳇢󵕢󸺥󸿉 󳇢 󷠴 󶔩 󼵼󷸾 󲁶 󸓔
󲰳󳧶󰻞󰵵󰾫󵈾󸿉󲘾󹈘󱌩󸿉󴚿󲔞󱌍󹉒󲔞󱌍󲨩󱞒󱔃󸿉󳇢
󵴞󷠴󶔩󶡋󱎹󲘲󰺄󸉨󰼠󲕳
3 )
󸿉󴃻󲼒󱾫󸁱󱔔󱲉󸑷󳍺󵉐󴙃󱠥󳃵󵉐󴋒󵔲󳉮󸁱󳃵󳑦󸑙󲦩
󱌩󱑹󵟂󱁃󲮔󱌣󱾆󰸶󱌣󳜘󰽚󶔩󳅜󳉸󳙟󱲉󲮔󱌣󰵴󳑦󸑙󲦩󱌩
󳃵󲮔󱌣󱾆󰸶󳍺󸔒󳞟󸔒󵉐󰼕󲘌󶩞󱙮󹀘
4 )
󱲉󵉐󱔔󲦩󱌩󳍺󸔒󰷔󱑹󼵼󳉮󳍉󳄿󳥤󷹉󶮝󸷭󱗑󳃵󳆚󳅜󸖱󵊇󱲉
󵉐󱔔󲦩󱌩󳝓󸎯󹄫󰻞󰵴󵒹󳆚󳅜󳃵󸷭󱗑󰼕󲘌󶩞󰺄󸉨󰼠󲕳
5 )
󳅜󰵷󷦴󸑃󱐕󰼾󲚞󳞟󱑡󴎥󲼒󵰩󸃉󴩀󱠥󸉨󰽥󲪃󷞃󸑰󳭌󶡋
󱲉󲼒󱾫󲺕󱎄󰵵󶡋󳥀󲁪󱲒󳍾󱑗󰽟󵉐󱔔󲦩󱌩
6 )
󵗢󷠴󸓔󲰳󰵷󷦴󵭭󲖉󳨡󷞇󳥫󳃵󰾇󳄦󹗒󱡸󷷯󰽺󵒹󱿣󱜅󱠥
󷞇󳥫󸑵󵨍󸑙󱔔󸛉󰻞󲖉󳨡󷞇󳥫󰾇󹗒󳃵󸻌󱜅󱜴󶡋󰼕󱙸󱌇
󸑙󱔔󸛉󰻞
7 )
󲁶󳩔󳏀󰿙󰸬󰵹󳍘󲚗󹃌󲘾󷸄󱾋󸑷󳍺󵈾󵒹󷠴󶔩󼵼󷦴󵟂󱁃󱌧
󸑷󳍺󲔥󲁪󰶃󰾫󵈾󲲥󲰳󰾫󵈾󹃌󲘾󷠴󶔩󱜴󸿮󰽜󲘾󲚗󲮹󸁱󵒹
󱙮󹀘
8 )
󰵷󷦴󱰕󰶺󹏹󶍗󰾫󵈾󲦩󱌩󶙝󰹢󵈱󵒹󴰀󲸫󲼮󶙝󳍉󰻅󸎾󲳲󼵼󲵑
󷨡󲦩󱌩󵒹󲔞󱌍󱎦󱐮󳪥󰶢󵿧󲳲󵒹󱔔󰽳󱜴󶡋󱲉󵚖󸾃󲘌󶩞󰶛
󸡿󵒹󰼠󲕳
d)
󵉐󱔔󲦩󱌩󰾫󵈾󱠥󴎥󲼒󰸳󹏡
1 )
󰵷󷦴󱕊󲰃󰾫󵈾󵉐󱔔󲦩󱌩󼵼󳭐󳌙󵈾󸔁󰾫󵈾󱝗󸓔󵒹󵉐󱔔󲦩󱌩
󸓦󵈾󱝗󸓔󵒹󳉾󴮒󹐅󲕂󱃪󷸄󷷧󵒹󵉐󱔔󲦩󱌩󰼕󰾫󰽺󲦩󰽳󳥀󳥤
󳙫 󳥀 󲔞 󱌍
2 )
󲁶󳩔󲮔󱌣󰵷󶡋󳍺󸔒󳃵󱌣󳜘󵉐󴙃󼵼󱐮󰵷󶡋󰾫󵈾󷸫󵉐󱔔󲦩󱌩
󰵷󶡋󸔒󸑃󲮔󱌣󳧼󳍾󱑗󵒹󵉐󱔔󲦩󱌩󳟾󱙮󹀘󵒹󰶃󲳴󹏣󸑴󷝥
󱁞󵀛
3 )
󱲉󸑴󷝥󰻤󰽧󷹉󶮝󳥀󳌄󸿢󰻞󳃵󸀟󲒹󵉐󱔔󲦩󱌩󰷔󱑹󼵼󲳴󹏣󰺣
󵉐󴙃󰵴󳈭󳍉󳏄󱿣󱠥󳃵󱙹󰵵󵉐󴋒󱖬󼵸󲁶󱜴󳈓󱙹󼵹󸑰󵨬󸿉󳇢
󲶎󵒹󲔞󱌍󳎄󳜷󸿮󰽜󰸬󵉐󱔔󲦩󱌩󲼒󱾫󸁱󱔔󵒹󹑦󹀘
4 )
󲘝󸾁󶔩󰵷󵈾󵒹󵉐󱔔󲦩󱌩󸀟󲒹󱲉󱋅󵱚󳄿󱛻󶲵󱰶󰷔󱾫󼵼󲪈󰶃󰵷
󱋉󷷾󰵷󴰀󲸫󵉐󱔔󲦩󱌩󱠥󰵷󰸬󷩓󸑰󰹉󷸺󳟉󵒹󰺄󳕽󰽳󵉐󱔔󲦩
󱌩󵉐󱔔󲦩󱌩󱲉󳦣󶑒󱷇󷷳󵒹󰾫󵈾󶙐󳅜󰶦󳟾󱙮󹀘󵒹
5 )
󶑷󳇢󵉐󱔔󲦩󱌩󱛻󱌧󸿢󰻞󳰭󳫆󸑙󱔔󸛉󰻞󳟾󱞅󷹉󳚯󱑍󰽚󳃵󱙔
󰽟󼵼󳰭󳫆󹄫󰻞󵝷󳌁󲺕󱎄󱠥󲱨󱢈󵉐󱔔󲦩󱌩󸑙󷝥󵒹󱌧󰺮󴸑󱎄
󲁶󳥤󳌁󱳂󼵼󲪿󱲉󰾫󵈾󱑹󱁞󵀛󲁪󵉐󱔔󲦩󱌩󷷾󱾵󰸳󳙧󳟾󵉌󶑷
󳇢󰵷󶭼󵒹󵉐󱔔󲦩󱌩󲮹󱜅󵒹
6 )
󱁃󳉰󱐘󱑵󱐊󱌩󸹔󱑅󱠥󴕢󴏈󶑷󳇢󶭼󲁪󱲒󳥤󸹔󱑅󱐘󱑵󱐏󵒹󱐊
󱌩󰵷󳟓󱙔󰽟󶙝󰶃󲖃󳟓󳍾󱑗
7 )
󳉾󴮒󰾫󵈾󷸺󳟉󰷽󼵼󲪈󶙍󷐋󰽳󰶍󳧶󰻞󱠥󷦴󸑴󷝥󵒹󰽳󰶍󳧼󸓦󳉋
󵉐󱔔󲦩󱌩󸿢󰻞󱠥󲦩󱌩󵒹󱐊󱿣󵴞󲘝󵉐󱔔󲦩󱌩󵈾󰸶󸙢󰹉󰵹
󱌧󵈾󸔁󰵷󵳘󵒹󳕽󰽳󱜴󶡋󰼕󲘌󶩞󱙮󹀘󲺕󱎄
8 )
󱁃󳉰󳅜󳪒󱠥󳏤󳉰󷞎󹈘󲪂󴲖󴕢󴏈󼵼󰵷󲲥󴍟󳥤󴍙󶡓󱲉󲼒
󱾫󵒹󲺕󱎄󰵵󼵼󴘫󴚿󵒹󳅜󳪒󰵷󶡋󱁃󷸇󳏤󳉰󵒹󲔞󱌍󱠥󲘇󲦩󱌩
󵒹󳍾󱑗
e)
󵉐󴋒󲮮󲦩󱌩󰾫󵈾󱠥󴎥󲼒󰸳󹏡󽴼
1 )
󰺒󰾫󵈾󵈱󰹢󶙐󷨟󲕂󵒹󱋏󵉐󱬽󱋏󵉐󲘝󸓔󵈾󰸶󳪥󵨬󵉐󴋒󱖬󵒹
󱋏󵉐󱬽󵈾󱑍󱌧󰺮󵉐󴋒󱖬󳞟󱜴󶡋󰼕󱜅󵈱󵗢󴦡󱙮󹀘
2 )
󰺒󰾫󵈾󸞂󳥤󰶂󵈾󵉐󴋒󱖬󵒹󵉐󱔔󲦩󱌩󰾫󵈾󱌧󰺮󵉐󴋒󱖬󱜴󶡋
󰼕󰹢󵈱󰼠󲕳󱠥󵗢󴦡󱙮󹀘
3 )
󲰳󵉐󴋒󱖬󰵷󵈾󳞟󼵼󲘝󲔑󸑵󵨍󱌧󰺮󸢅󲚪󴶠󰽥󼵼󰾿󲁶󱰑󲱏󸷐
󵞾 󲧐 󸷭 󱗑 󸷑 󲒪 󷙡 󸷑 󳃵 󱌧 󰺮 󲘮 󸢅 󲚪 󴶠 󰽥 󼵼󰻅 󸿉 󵉐 󴋒 󱖬
󰵨󵱯󰵹󱜦󰵨󵱯󸑷󳍺󵉐󴋒󶑇󵱯󸛉󵜋󸄠󰼕󲮹󸁱󴱎󴪕󳃵󵗢󴦡
4 )
󱲉󴛞󵈾󳧶󰻞󰵵󼵼󴓋󰽥󱜴󶡋󰼕󰺣󵉐󴋒󶑇󰶦󴘲󱐁󼵼󲪿󸘚󱋞󳍺
󷩙󲁶󳩔󲼒󱾫󵠦󱑍󴓋󰽥󼵼󵈾󴊑󱍿󴏥󲁶󳩔󴓋󰽥󵠦󱑍󰸬󵗛
󵘌󼵼󸑯󷦴󲘋󴊡󱘖󵋬󲨑󱔕󰺣󵉐󴋒󰶦󴘲󱐁󵒹󴓋󰽥󱜴󶡋󰼕󱜅󵈱
󶣲󷑥󳃵󴱎󴪕
5 )
󰵷󷦴󰾫󵈾󳌁󱳂󳃵󳙗󷠴󸑃󵒹󵉐󴋒󱖬󳃵󲦩󱌩󳌁󱳂󳃵󳙗󷠴󸑃
󵒹󵉐󴋒󶑇󱜴󶡋󱟄󴾢󳝾󴎂󹏬󴐶󵒹󶑖󳩔󼵼󲘌󶩞󵗢󴦡󴳙󴨾󳃵
󰼠󲕳
6 )
󰵷󷦴󲘝󵉐󴋒󱖬󳣑󹆫󰸶󴦡󳃵󶙐󹠟󴖜󰶦󵉐󴋒󱖬󳣑󹆫󰸶󴦡󳃵󹠟
󰸶
130 °C
󵒹󹠟󴖜󰶦󱜴󶡋󲘌󶩞󴳙󴨾
f)
󶑷󱁞
1 )
󷷯󰶂󰶍󶑷󱁞󰺄󱟘󰾫󵈾󵕲󱝛󵒹󱾋󰻞󶑷󱁞󵉐󱔔󲦩󱌩󸑰󲘝󱁃
󷸇󳄿󶑷󱁞󵒹󵉐󱔔󲦩󱌩󵒹󲔞󱌍
2 )
󱎀󰵷󶡋󶑷󱁞󳌁󱳂󵒹󵉐󴋒󱖬󵉐󴋒󱖬󰺒󶡋󵉌󵈱󰹢󶙐󳃵󱌧󳍈󳧊
󵒹󶑷󱁞󳥫󱔊󱥂󸑴󷝥󶑷󱁞
5
󵶎󰽥󰶦󳛓
󵉐󸸃
Drill
󰶂󵈾󷵪󱟈󷸳󽴼
󰾫󵈾󱍿󱐂󵉐󸸃󳞟󷦴󳄦󲁪󶚮󶔠󳣑󹆫󱲉󱬿󱽯󰶦󰼕󲮹󸁱󱞒󱔃󳌁󰼠
󰾫󵈾󹁦󲦩󱌩󳏀󰿙󵒹󸏈󱔕󳅜󳪒󳕽󰽳󱿠󳅜󰼕󲮹󸁱󰺄󸉨󰼠󲕳
󲰳󱲉󸸃󱑵󸿢󰻞󱜴󶡋󷩙󱛻󳢞󶑂󰷔󱾆󸑴󷝥󳕽󰽳󳞟󼵼󷦴󸔒󸑃󶑠󶒛󳏤󳉰󹈘
󳧼󳏤󳉰󲦩󱌩󸸃󱑵󸿢󰻞󵠦󱑍󲨅󵉐󲘌󶑂󰼕󰾫󲦩󱌩󱾫󹆫󵒹󸢅󲚪󹄫󰻞󲨅
󵉐󰺣󶙝󰾫󳕽󰽳󶙐󱜍󱑍󵉐󱐂
󳄿󳥤󳕽󰽳󵒹󲔞󱌍󳉸󵤚
󲁶󳩔󱲉󳆅󷝥󳕽󰽳󳞟󱐘󱒷󸞂󰻞󳃵󶄓󱱀󰻞󱜴󶡋󰼕󳍺󷩙󹁨󷋢󵒹󵉐
󶑂󼵼󷸽󳏤󰽟󵉐󱔔󲦩󱌩󵒹󶑠󶒛󳅜󳪒󷞎󹈘󱐘󱒷󸞂󰻞󳃵󶄓󱱀󰻞󲁶
󳩔󳍺󷩙󱑍
󲨅󵉐
󲘌󶑂󼵼󵉐󱔔󲦩󱌩󵒹󸢅󲚪󸛉󰻞󷞎󹈘󲙡󰼕
󲨅󵉐
󼵼
󲪈󰾫󳕽󰽳󰺄󱟘󷩙󵉐
󰾫󵈾󸻌󸸃󱿣󵒹󲔞󱌍󷸺󳟉
󱐘󱖢󰻅󹠟󰸶󸸃󱿣󳥓󱿑󹐅󲕂󸔠󲫟󵒹󸔠󲫟󸑙󷝥󱲉󸏆󹠟󵒹󸔠󲫟
󰵵󼵼󲁶󳩔󱋉󷷾󱲉󰵷󳍺󷩙󲦩󰻞󵒹󲺕󱎄󰵵󶩉󵉌󳝓󸎯󼵼󸸃󱿣󱜴󶡋󰼕󲯯
󳤽󼵼󰺣󶙝󲘌󶩞󰺄󸉨󰼠󲕳
󲄥󶑋󰻅󰽜󸔠󸑴󷝥󸸃󲒱󼵼󸸃󱿣󲘻󵱯󰵹󲦩󰻞󱁃󳉰󳍺󷩙󱲉󸏆󹠟󵒹
󸔠󲫟󰵵󼵼󲁶󳩔󱋉󷷾󱲉󰵷󳍺󷩙󲦩󰻞󵒹󲺕󱎄󰵵󶩉󵉌󳝓󸎯󼵼󸸃󱿣󱜴󶡋
󰼕󲯯󳤽󼵼󰺣󶙝󲘌󶩞󰺄󸉨󰼠󲕳
󰺒󱲉󰵹󸸃󱿣󵕭󳍺󲘇󹿆󳞟󳜷󱔉󱚔󱔃󼵼󲪈󰶃󰵷󳜷󱔉󸑃󱿑󵒹󱚔󱔃
󸸃󱿣󱜴󶡋󲯯󳤽󶩞󵝷󳌁󳃵󱿠󳍾󼵼󰺣󶙝󲘌󶩞󰺄󸉨󰼠󲕳
󵉐󸸃󸿢󱔉󲔞󱌍󷵪󱟈
󰾫󵈾󱿫󱌩󳃵󸡸󱜌󱌧󲔑󱜴󷝥󵒹󳜱󴎂󼵼󲘝󲦩󰻞󱱀󲕂󳙆󳔓󱑍󵫙󲕂
󵒹󲪃󱜶󰵴󳅜󳉰󳃵󵈾󸉨󰽥󹏞󰽟󲦩󰻞󸛫󳟾󰵷󵫙󲕂󵒹󼵼󰼕󲘌󶩞󳕽
󰽳󱿠󳍾
󸿢󰻞󱠥󲦩󱌩󱜴󶡋󰼕󱲉󰾫󵈾󸑃󵪑󰶦󱜅󴪛󲁶󳩔󸑴󷝥󳙟󴪛󲪿󵈾
󽵈 󲁶 󸢅 󲚪 󸸃 󲒱 󽵉 󼵼󱾆 󵀛 󳞟 󷸽 󰾇 󳄦 󳅜 󲀜
󸔒 󹑦 󱜢 󸔒 󲨣 󰼕 󵔸 󰽟 󸑙 󱔔 󸛉 󰻞 󼵼󲪿 󰸯 󰻅 󸘚 󱋞 󲖉 󳨡 󷞇 󳥫 󰾇 󹗒 󳃵
󸻌󱜅󱜴󶡋󰼕󱙸󱌇󸑙󱔔󸛉󰻞
󱒦󰽯󹑦󹀘
󲙵󵷘󸗾󲔜󰸬󵕲󱌣󵒹󲔞󱌍󴎂󷨟󲪈󸡸󵈾󰸬󲔞󱌍󷠴󱾋󼵼󳪥󰹉󱒦󰽯󹑦󹀘󰺡
󴬭󳟾󳝾󴎂󸘚󱋞󵒹󸑰󰹉󹑦󹀘󱖬󳉎󽴼
󱞒󱔃󳌁󰼠
󹑸󴘲󹏿󵿝󸔤󳃮󵒹󰺄󸉨󰼠󲕳󹑦󹀘
󰾫󵈾󳞟󸿢󰻞󱜅󴪛󲘌󶩞󵒹󴧃󰼠󹑦󹀘
󸻌󳞟󸾃󰾫󵈾󲮹󸁱󵒹󰺄󸉨󰼠󲕳󹑦󹀘
󷸽󲃇󱦥󱁃󵷘󲁪󸑰󰹉󷸺󳟉
󱋏󵉐󱬽
DeWALT
󱋏󵉐󱬽󳝾󹄾󱄟󱐁󰻤󰽧󷹉󳚯󼵼󰶂󰶺󵶎󳟓󳕽󰽳󶙝󷸄󷷧
󵉐󴉟󲔞󱌍
󵉐󳦽󱜬󸓔󵈾󰵨󵨬󲦩󰽳󵉐󱚔󷸽󱔊󲳴󳰭󳫆󵉐󴋒󶑇󵒹󵉐󱚔󳟾󱞅󱠥󸸶󴵦
󰵴󵒹󵉐󱚔󰵨󶩞󱜦󱾫󼵼󷸽󵟂󱁃󱋏󵉐󱬽󵉐󱚔󱠥󰶻󵉐󴙃󵒹󵉐󱚔󰵨󶩞
DeWALT
󱋏󵉐󱬽󵳘󱝗
IEC60335
󱛾󸡿󶑠󶒛󷦴󴊡󼵼󱰕󴃽󳝾
󹄾󰾫󵈾󳍺󱲒󶑂
󲁶󳩔󵉐󴙃󶑂󳌁󱳂󼵼󲳴󹏣󸡸󵈾
DeWALT
󶑷󱁞󳦽󳨭󳏀󰿙󵒹󰶂󵈾󵉐󶑂
󸑴󷝥󳥀󳌄
󰾫󵈾󲮂󸻌󶑂
󹀒󹈌󶑠󲘇󲳴󷦴󼵼󱞅󱐮󷸽󱖢󰾫󵈾󲮂󸻌󶑂󰾫󵈾󸓔󱝗󲹡󵒹󱋏󵉐󱬽󸏖󱌇
󱔇󴽨󵒹󱝗󳭕󲮂󸻌󶑂󼵸󷨜
󳆯󳦪󱛭󳚩
󼵹󳥓 󲘮 󵒹 󲘌 󶑂 󲙰 󲘅 󰶺
1
󲪃󳜱󴈘
󵾜 󽴽󳥓 󱿑 󸻌 󲫟 󰶺
30
󵾜
󰾫󵈾󵉐󶒉󱙸󵴳󳞟󼵼󷸽󱔊󲳴󳈙󱐁󳄿󳥤󵒹󵉐󶒉
󸷐󲘇󳄿󳥤󵉐󴋒󱋏󵉐󱬽󵒹󸡿󷦴󲔞󱌍󷸺󳟉
󷸽󲃇󱦥󱁃󵷘󲁪󸑰󰹉󷸺󳟉󽴼
󳦦󳅜󱍄󱖬󱞏󸡿󷦴󵒹󱌰󲖃󵉐󴋒󱋏󵉐󱬽󲔞󱌍
󱠥 󳕽 󰽳 󷸺 󳟉󼵸 󷸽 󱛭 󸾔
󳆯󳦪󱛭󳚩
󼵹
󱲉󰾫󵈾󱋏󵉐󱬽󰷔󱑹󼵼󷸽󱋔󸾔󷹁󳄿󳥤󳉸󵤚󰻅󱛻󱋏󵉐󱬽󵉐󴋒󶑇󱠥
󰾫󵈾󵉐󴋒󶑇󵒹󰹢󱡸󰵴󵒹󷵪󵤚󳫼󷷶
󷵪󱟈󽴼󷩙󵉐󱙮󹀘󷸽󱖢󷷯󰻤󰽧󴓋󰽥󴕸󱌇󱋏󵉐󱬽󼵼󱞅󱐮󰼕󲮹
󸁱󷩙󵉐
󷵪󱟈󽴼󳃯󰻍󲮋󷷴󰾫󵈾󴜪󵉐󱁃󳇢󹐅󲕂󵉐󴐩󰶺
30
󴈘󲔞󳃵󰻅󰵵
󵒹󴜪󵉐󱁃󳇢󷠴󶔩
󷵪󵤚󽴼󴧃󰼠󱙮󹀘󰶺󸿮󰽜󰺄󸉨󰼠󲕳󹑦󹀘󼵼󷸽󰺒󰾫󵈾
D
eWALT
󱋏󵉐󲮮󵉐󴋒󱋏󵉐󰾫󵈾󱌧󲔑󵾬󱴘󵒹󵉐󴋒󱜴󶡋󰼕󲮹
󸁱󴳙󷠭󼵼󲪈󲘌󶩞󰺄󸉨󰼠󲕳󱠥󳌁󲕳
󷵪󵤚󽴼󲪿󵖐󵷘󲁪󱋅󵱚󼵼󰻅󵟂󱁃󰺮󰻍󰵷󲘝󴃽󷸄󱾋󲰳󱄟󴾗󱌩
󳧼󴾗
󴎥󲼒󽴼󱲉󳪥󰹉󲺕󱎄󰵵󼵼󲰳󱋏󵉐󱬽󵒹󳏄󱿣󳏄󱌇󵉐󴙃󳏄󲫡󳞟󼵼
󱋏󵉐󱬽󱌼󸛉󷢘󹆫󵒹󱋏󵉐󳍺󷩙󴩀󱜴󶡋󱰕󰶺󱾫󳧼󴶠󰻞󶙝󵜋󸄠
󷸽󱖢󷷯󶡋󲘌󵉐󵒹󲮘󴶠󹈒󸑜󱋏󵉐󱬽󶣽󼵼󸑰󰹉󱾫󳧼󴶠󰻞󱖬󳉎
󰽏󰵷󸿴󰸶󸷪󳰽󸸦󵶸󳃵󰻤󰽧󸢅󲚪󹏿󵿝󵒹󱷝󵩥󴶠󱋏󵉐󱬽󱌼
󴌶󳥤󵉐󴋒󶑇󳞟󼵼󷸽󳜘󲮔󱋏󵉐󱬽󰵹󵉐󴙃󵒹󸑷󳍺󴕢󴏥󱑹󼵼󱔊
󲳴󳈭󳍉󱋏󵉐󱬽
󷸽󱖢󷸛󱱄󰾫󵈾󳦦󳅜󱍄󳉸󲕂󵒹󱋏󵉐󱬽󰻅󱾫󵒹󱌧󰺮󰻤󰽧󱋏󵉐󱬽
󰶺󵉐󴋒󶑇󱋏󵉐󱋏 󵉐 󱬽 󱠥 󵉐 󴋒 󶑇 󸛫 󳟾 󰶂 󸽷 󷸄 󷷧 󵒹 󼵼󰸾 󵕲 󸞂 󱝗
󰾫󵈾
󹀒󰸬󰶺
DeWALT
󱋏󵉐󲮮󵉐󴋒󱋏󵉐󰻅󱾫󼵼󸑰󰹉󱋏󵉐󱬽󲪈󹈌󷸄󷷧
󵈾󰸶󱌧󰺮󵈾󸔁󱞅󱐮󼵼󱜴󶡋󰼕󲘌󶩞󴦡󴧈󷩙󵉐󳃵󵉐󱐂
󷸽󱖢󲘝󱋏󵉐󱬽󳣑󹆫󰸶󹄎󰶦󳃵󹄔󰶦
󳜘󲮔󱋏󵉐󱬽󸑷󳍺󳞟󼵼󲪿󳈭󰵵󳏄󱿣󼵼󱐘󱖢󳈙󳉪󵉐󴙃󶑂󸑰󲘝󸿮󰽜
󲘇󵉐󳏄󱿣󱠥󵉐󶑂󵒹󳌁󲕳󹑦󹀘
󵟂󱁃󵉐󴙃󶑂󲧓󶔩󱲉󰵷󳟓󸅵󸅏󸅬󶑍󳈙󳆒󳃵󰼕󱜍󱑍󳌁󲕳󳃵󱚔
󱔃󵒹󰽚󶔩
󹀒󹈌󶑠󲘇󲳴󷦴󼵼󱞅󱐮󷸽󱖢󰾫󵈾󲮂󸻌󶑂󰾫󵈾󰵷󴃼󵟂󵒹󲮂󸻌󶑂
󱜴󶡋󲘌󶩞󴦡󴧈󷩙󵉐󳃵󵉐󱐂󵒹󹑦󹀘
󷸽󱖢󲘝󰻤󰽧󴶠󰻞󳙟󱲉󱋏󵉐󱬽󰵴󹈘󼵼󳃵󳟾󳆿󱋏󵉐󱬽󳙟󱲉󱜴󶡋󰼕
󱸨󰽟󸔒󹑦󳹶󵒹󳪬󸎲󷞎󹈘󼵼󲘌󶩞󱋏󵉐󱬽󵒹󱌼󸛉󸑃󴪛󷸽󳆿󱋏󵉐
󱬽󳙟󶔩󱲉󸑵󵨍󰻤󰽧󴪛󴙃󵒹󱲒󳜱󱋏󵉐󱬽󸔒󸑃󱾫󱽳󹏞󵱯󱠥󲫁󵱯
󵒹󳹶󸑴󷝥󸔒󹑦
󵦝󴃻󰾫󵈾󵉐󴙃󶑂󳃵󳏄󱿣󲦻󳌁󱳂󵒹󱋏󵉐󱬽󷸽󵰩󱙱󳥀󳌄󸑰󰹉
󱋏󵉐󱬽
󲁶󳩔󱋏󵉐󱬽󱜍󱑍󲰃󴩙󸡿󱐂󳍉󶽆󳃵󱐁󴾢󱌧󰺮󳌁󱳂󲺕󱎄󼵼󷸽󱖢
󰾫󵈾󱋏󵉐󱬽󷸽󲘝󳌁󱳂󵒹󱋏󵉐󱬽󸓑󱑍󳍈󳧊󳥫󱔊󰶦󲳲
󷸽󱖢󶩉󷝥󳈓󱙹󱋏󵉐󱬽󷸽󲘝󹄾󷦴󳰭󱁞󳃵󱁞󵀛󵒹󱋏󵉐󱬽󸓑󱑍󳍈
󳧊󳥫󱔊󰶦󲳲󸡿󷠴󰵷󴃼󵟂󱜴󶡋󲘌󶩞󷩙󵉐󵉐󱐂󳃵󴦡󴧈󹑦󹀘
󲳴󹏣󵰩󱙱󲘝󲦻󳌁󱳂󵒹󵉐󴙃󶑂󰹝󵉌󱑗󸔤󱥂󳥫󱔊󰻀󵀛󳃵󵾬󰽄󵒹
󱝗󳭕󰺄󱟘󸑴󷝥󳥀󳌄󰻅󸿉󴃻󲔞󱌍󹁨󲹗
󴕢󴏈󱑹󼵼󷸽󱋔󳜘󲮔󱋏󵉐󱬽󱠥󳏄󲫡󵒹󸑷󳍺󼵼󰻅󸿮󰽜󷩙󵉐󹑦󹀘
󱜌󱐁󵉐󴋒󶑇󰵷󰼕󸿮󰽜󴃽󹑦󹀘
󱐘󱖢󲘝󰶚󰶢󱋏󵉐󱬽󸑷󳍺󱲉󰵨󸁱
󱋏󵉐󱬽󳟾󰶺
220 V
󵒹󳫼󱎦󲕼󵈾󵉐󴙃󶙝󷸄󷷧󷸽󱖢󷸛󱱄󱲉󰻤󰽧
󱌧󰺮󵉐󱚔󰵵󰾫󵈾󱋏󵉐󱬽󴃽󷨟󱐮󰵷󸓔󵈾󰸶󸎩󸏀󱋏󵉐󱬽
󰶺󵉐󴋒󱋏󵉐󼵸󱱄
B
󼵹
1.
󳙟󸑴󵉐󴋒󶑇󱑹󼵼󱋔󲘝󱋏󵉐󱬽󵒹󳏄󱿣󳏄󱑍󵕲󲪿󵒹󵉐󴙃󳏄󲫡󰵴
2.
󲘝󵉐󴋒󶑇
1
󳏄 󱌇 󱑍 󱋏 󵉐 󱬽 󰶦 󼵼󵟂 󲕂 󵉐 󴋒 󶑇 󲔥 󱌍 󲙡 󰽚 󶐥 󶮁
󽵈󱋏󵉐󰶦󽵉
󳉸󵤚󴦨󲘝󰵷󳜘󸽹󴩍󼵼󷞎󵤚󱋏󵉐󸑃󵪑󲦻󶑒󲮔󲄥
13
简体中文
5
󵶎󰽥󰶦󳛓
󵉐󸸃
Drill
󰶂󵈾󷵪󱟈󷸳󽴼
󰾫󵈾󱍿󱐂󵉐󸸃󳞟󷦴󳄦󲁪󶚮󶔠󳣑󹆫󱲉󱬿󱽯󰶦󰼕󲮹󸁱󱞒󱔃󳌁󰼠
󰾫󵈾󹁦󲦩󱌩󳏀󰿙󵒹󸏈󱔕󳅜󳪒󳕽󰽳󱿠󳅜󰼕󲮹󸁱󰺄󸉨󰼠󲕳
󲰳󱲉󸸃󱑵󸿢󰻞󱜴󶡋󷩙󱛻󳢞󶑂󰷔󱾆󸑴󷝥󳕽󰽳󳞟󼵼󷦴󸔒󸑃󶑠󶒛󳏤󳉰󹈘
󳧼󳏤󳉰󲦩󱌩󸸃󱑵󸿢󰻞󵠦󱑍󲨅󵉐󲘌󶑂󰼕󰾫󲦩󱌩󱾫󹆫󵒹󸢅󲚪󹄫󰻞󲨅
󵉐󰺣󶙝󰾫󳕽󰽳󶙐󱜍󱑍󵉐󱐂
󳄿󳥤󳕽󰽳󵒹󲔞󱌍󳉸󵤚
󲁶󳩔󱲉󳆅󷝥󳕽󰽳󳞟󱐘󱒷󸞂󰻞󳃵󶄓󱱀󰻞󱜴󶡋󰼕󳍺󷩙󹁨󷋢󵒹󵉐
󶑂󼵼󷸽󳏤󰽟󵉐󱔔󲦩󱌩󵒹󶑠󶒛󳅜󳪒󷞎󹈘󱐘󱒷󸞂󰻞󳃵󶄓󱱀󰻞󲁶
󳩔󳍺󷩙󱑍
󲨅󵉐
󲘌󶑂󼵼󵉐󱔔󲦩󱌩󵒹󸢅󲚪󸛉󰻞󷞎󹈘󲙡󰼕
󲨅󵉐
󼵼
󲪈󰾫󳕽󰽳󰺄󱟘󷩙󵉐
󰾫󵈾󸻌󸸃󱿣󵒹󲔞󱌍󷸺󳟉
󱐘󱖢󰻅󹠟󰸶󸸃󱿣󳥓󱿑󹐅󲕂󸔠󲫟󵒹󸔠󲫟󸑙󷝥󱲉󸏆󹠟󵒹󸔠󲫟
󰵵󼵼󲁶󳩔󱋉󷷾󱲉󰵷󳍺󷩙󲦩󰻞󵒹󲺕󱎄󰵵󶩉󵉌󳝓󸎯󼵼󸸃󱿣󱜴󶡋󰼕󲯯
󳤽󼵼󰺣󶙝󲘌󶩞󰺄󸉨󰼠󲕳
󲄥󶑋󰻅󰽜󸔠󸑴󷝥󸸃󲒱󼵼󸸃󱿣󲘻󵱯󰵹󲦩󰻞󱁃󳉰󳍺󷩙󱲉󸏆󹠟󵒹
󸔠󲫟󰵵󼵼󲁶󳩔󱋉󷷾󱲉󰵷󳍺󷩙󲦩󰻞󵒹󲺕󱎄󰵵󶩉󵉌󳝓󸎯󼵼󸸃󱿣󱜴󶡋
󰼕󲯯󳤽󼵼󰺣󶙝󲘌󶩞󰺄󸉨󰼠󲕳
󰺒󱲉󰵹󸸃󱿣󵕭󳍺󲘇󹿆󳞟󳜷󱔉󱚔󱔃󼵼󲪈󰶃󰵷󳜷󱔉󸑃󱿑󵒹󱚔󱔃
󸸃󱿣󱜴󶡋󲯯󳤽󶩞󵝷󳌁󳃵󱿠󳍾󼵼󰺣󶙝󲘌󶩞󰺄󸉨󰼠󲕳
󵉐󸸃󸿢󱔉󲔞󱌍󷵪󱟈
󰾫󵈾󱿫󱌩󳃵󸡸󱜌󱌧󲔑󱜴󷝥󵒹󳜱󴎂󼵼󲘝󲦩󰻞󱱀󲕂󳙆󳔓󱑍󵫙󲕂
󵒹󲪃󱜶󰵴󳅜󳉰󳃵󵈾󸉨󰽥󹏞󰽟󲦩󰻞󸛫󳟾󰵷󵫙󲕂󵒹󼵼󰼕󲘌󶩞󳕽
󰽳󱿠󳍾
󸿢󰻞󱠥󲦩󱌩󱜴󶡋󰼕󱲉󰾫󵈾󸑃󵪑󰶦󱜅󴪛󲁶󳩔󸑴󷝥󳙟󴪛󲪿󵈾
󽵈 󲁶 󸢅 󲚪 󸸃 󲒱 󽵉 󼵼󱾆 󵀛 󳞟 󷸽 󰾇 󳄦 󳅜 󲀜
󸔒 󹑦 󱜢 󸔒 󲨣 󰼕 󵔸 󰽟 󸑙 󱔔 󸛉 󰻞 󼵼󲪿 󰸯 󰻅 󸘚 󱋞 󲖉 󳨡 󷞇 󳥫 󰾇 󹗒 󳃵
󸻌󱜅󱜴󶡋󰼕󱙸󱌇󸑙󱔔󸛉󰻞
󱒦󰽯󹑦󹀘
󲙵󵷘󸗾󲔜󰸬󵕲󱌣󵒹󲔞󱌍󴎂󷨟󲪈󸡸󵈾󰸬󲔞󱌍󷠴󱾋󼵼󳪥󰹉󱒦󰽯󹑦󹀘󰺡
󴬭󳟾󳝾󴎂󸘚󱋞󵒹󸑰󰹉󹑦󹀘󱖬󳉎󽴼
󱞒󱔃󳌁󰼠
󹑸󴘲󹏿󵿝󸔤󳃮󵒹󰺄󸉨󰼠󲕳󹑦󹀘
󰾫󵈾󳞟󸿢󰻞󱜅󴪛󲘌󶩞󵒹󴧃󰼠󹑦󹀘
󸻌󳞟󸾃󰾫󵈾󲮹󸁱󵒹󰺄󸉨󰼠󲕳󹑦󹀘
󷸽󲃇󱦥󱁃󵷘󲁪󸑰󰹉󷸺󳟉
󱋏󵉐󱬽
DeWALT
󱋏󵉐󱬽󳝾󹄾󱄟󱐁󰻤󰽧󷹉󳚯󼵼󰶂󰶺󵶎󳟓󳕽󰽳󶙝󷸄󷷧
󵉐󴉟󲔞󱌍
󵉐󳦽󱜬󸓔󵈾󰵨󵨬󲦩󰽳󵉐󱚔󷸽󱔊󲳴󳰭󳫆󵉐󴋒󶑇󵒹󵉐󱚔󳟾󱞅󱠥󸸶󴵦
󰵴󵒹󵉐󱚔󰵨󶩞󱜦󱾫󼵼󷸽󵟂󱁃󱋏󵉐󱬽󵉐󱚔󱠥󰶻󵉐󴙃󵒹󵉐󱚔󰵨󶩞
DeWALT
󱋏󵉐󱬽󵳘󱝗
IEC60335
󱛾󸡿󶑠󶒛󷦴󴊡󼵼󱰕󴃽󳝾
󹄾󰾫󵈾󳍺󱲒󶑂
󲁶󳩔󵉐󴙃󶑂󳌁󱳂󼵼󲳴󹏣󸡸󵈾
DeWALT
󶑷󱁞󳦽󳨭󳏀󰿙󵒹󰶂󵈾󵉐󶑂
󸑴󷝥󳥀󳌄
󰾫󵈾󲮂󸻌󶑂
󹀒󹈌󶑠󲘇󲳴󷦴󼵼󱞅󱐮󷸽󱖢󰾫󵈾󲮂󸻌󶑂󰾫󵈾󸓔󱝗󲹡󵒹󱋏󵉐󱬽󸏖󱌇
󱔇󴽨󵒹󱝗󳭕󲮂󸻌󶑂󼵸󷨜
󳆯󳦪󱛭󳚩
󼵹󳥓 󲘮 󵒹 󲘌 󶑂 󲙰 󲘅 󰶺
1
󲪃󳜱󴈘
󵾜 󽴽󳥓 󱿑 󸻌 󲫟 󰶺
30
󵾜
󰾫󵈾󵉐󶒉󱙸󵴳󳞟󼵼󷸽󱔊󲳴󳈙󱐁󳄿󳥤󵒹󵉐󶒉
󸷐󲘇󳄿󳥤󵉐󴋒󱋏󵉐󱬽󵒹󸡿󷦴󲔞󱌍󷸺󳟉
󷸽󲃇󱦥󱁃󵷘󲁪󸑰󰹉󷸺󳟉󽴼
󳦦󳅜󱍄󱖬󱞏󸡿󷦴󵒹󱌰󲖃󵉐󴋒󱋏󵉐󱬽󲔞󱌍
󱠥 󳕽 󰽳 󷸺 󳟉󼵸 󷸽 󱛭 󸾔
󳆯󳦪󱛭󳚩
󼵹
󱲉󰾫󵈾󱋏󵉐󱬽󰷔󱑹󼵼󷸽󱋔󸾔󷹁󳄿󳥤󳉸󵤚󰻅󱛻󱋏󵉐󱬽󵉐󴋒󶑇󱠥
󰾫󵈾󵉐󴋒󶑇󵒹󰹢󱡸󰵴󵒹󷵪󵤚󳫼󷷶
󷵪󱟈󽴼󷩙󵉐󱙮󹀘󷸽󱖢󷷯󰻤󰽧󴓋󰽥󴕸󱌇󱋏󵉐󱬽󼵼󱞅󱐮󰼕󲮹
󸁱󷩙󵉐
󷵪󱟈󽴼󳃯󰻍󲮋󷷴󰾫󵈾󴜪󵉐󱁃󳇢󹐅󲕂󵉐󴐩󰶺
30
󴈘󲔞󳃵󰻅󰵵
󵒹󴜪󵉐󱁃󳇢󷠴󶔩
󷵪󵤚󽴼󴧃󰼠󱙮󹀘󰶺󸿮󰽜󰺄󸉨󰼠󲕳󹑦󹀘󼵼󷸽󰺒󰾫󵈾
DeWALT
󱋏󵉐󲮮󵉐󴋒󱋏󵉐󰾫󵈾󱌧󲔑󵾬󱴘󵒹󵉐󴋒󱜴󶡋󰼕󲮹
󸁱󴳙󷠭󼵼󲪈󲘌󶩞󰺄󸉨󰼠󲕳󱠥󳌁󲕳
󷵪󵤚󽴼󲪿󵖐󵷘󲁪󱋅󵱚󼵼󰻅󵟂󱁃󰺮󰻍󰵷󲘝󴃽󷸄󱾋󲰳󱄟󴾗󱌩
󳧼󴾗
󴎥󲼒󽴼󱲉󳪥󰹉󲺕󱎄󰵵󼵼󲰳󱋏󵉐󱬽󵒹󳏄󱿣󳏄󱌇󵉐󴙃󳏄󲫡󳞟󼵼
󱋏󵉐󱬽󱌼󸛉󷢘󹆫󵒹󱋏󵉐󳍺󷩙󴩀󱜴󶡋󱰕󰶺󱾫󳧼󴶠󰻞󶙝󵜋󸄠
󷸽󱖢󷷯󶡋󲘌󵉐󵒹󲮘󴶠󹈒󸑜󱋏󵉐󱬽󶣽󼵼󸑰󰹉󱾫󳧼󴶠󰻞󱖬󳉎
󰽏󰵷󸿴󰸶󸷪󳰽󸸦󵶸󳃵󰻤󰽧󸢅󲚪󹏿󵿝󵒹󱷝󵩥󴶠󱋏󵉐󱬽󱌼
󴌶󳥤󵉐󴋒󶑇󳞟󼵼󷸽󳜘󲮔󱋏󵉐󱬽󰵹󵉐󴙃󵒹󸑷󳍺󴕢󴏥󱑹󼵼󱔊
󲳴󳈭󳍉󱋏󵉐󱬽
󷸽󱖢󷸛󱱄󰾫󵈾󳦦󳅜󱍄󳉸󲕂󵒹󱋏󵉐󱬽󰻅󱾫󵒹󱌧󰺮󰻤󰽧󱋏󵉐󱬽
󰶺󵉐󴋒󶑇󱋏󵉐󱋏 󵉐 󱬽 󱠥 󵉐 󴋒 󶑇 󸛫 󳟾 󰶂 󸽷 󷸄 󷷧 󵒹 󼵼󰸾 󵕲 󸞂 󱝗
󰾫󵈾
󹀒󰸬󰶺
DeWALT
󱋏󵉐󲮮󵉐󴋒󱋏󵉐󰻅󱾫󼵼󸑰󰹉󱋏󵉐󱬽󲪈󹈌󷸄󷷧
󵈾󰸶󱌧󰺮󵈾󸔁󱞅󱐮󼵼󱜴󶡋󰼕󲘌󶩞󴦡󴧈󷩙󵉐󳃵󵉐󱐂
󷸽󱖢󲘝󱋏󵉐󱬽󳣑󹆫󰸶󹄎󰶦󳃵󹄔󰶦
󳜘󲮔󱋏󵉐󱬽󸑷󳍺󳞟󼵼󲪿󳈭󰵵󳏄󱿣󼵼󱐘󱖢󳈙󳉪󵉐󴙃󶑂󸑰󲘝󸿮󰽜
󲘇󵉐󳏄󱿣󱠥󵉐󶑂󵒹󳌁󲕳󹑦󹀘
󵟂󱁃󵉐󴙃󶑂󲧓󶔩󱲉󰵷󳟓󸅵󸅏󸅬󶑍󳈙󳆒󳃵󰼕󱜍󱑍󳌁󲕳󳃵󱚔
󱔃󵒹󰽚󶔩
󹀒󹈌󶑠󲘇󲳴󷦴󼵼󱞅󱐮󷸽󱖢󰾫󵈾󲮂󸻌󶑂󰾫󵈾󰵷󴃼󵟂󵒹󲮂󸻌󶑂
󱜴󶡋󲘌󶩞󴦡󴧈󷩙󵉐󳃵󵉐󱐂󵒹󹑦󹀘
󷸽󱖢󲘝󰻤󰽧󴶠󰻞󳙟󱲉󱋏󵉐󱬽󰵴󹈘󼵼󳃵󳟾󳆿󱋏󵉐󱬽󳙟󱲉󱜴󶡋󰼕
󱸨󰽟󸔒󹑦󳹶󵒹󳪬󸎲󷞎󹈘󼵼󲘌󶩞󱋏󵉐󱬽󵒹󱌼󸛉󸑃󴪛󷸽󳆿󱋏󵉐
󱬽󳙟󶔩󱲉󸑵󵨍󰻤󰽧󴪛󴙃󵒹󱲒󳜱󱋏󵉐󱬽󸔒󸑃󱾫󱽳󹏞󵱯󱠥󲫁󵱯
󵒹󳹶󸑴󷝥󸔒󹑦
󵦝󴃻󰾫󵈾󵉐󴙃󶑂󳃵󳏄󱿣󲦻󳌁󱳂󵒹󱋏󵉐󱬽󷸽󵰩󱙱󳥀󳌄󸑰󰹉
󱋏󵉐󱬽
󲁶󳩔󱋏󵉐󱬽󱜍󱑍󲰃󴩙󸡿󱐂󳍉󶽆󳃵󱐁󴾢󱌧󰺮󳌁󱳂󲺕󱎄󼵼󷸽󱖢
󰾫󵈾󱋏󵉐󱬽󷸽󲘝󳌁󱳂󵒹󱋏󵉐󱬽󸓑󱑍󳍈󳧊󳥫󱔊󰶦󲳲
󷸽󱖢󶩉󷝥󳈓󱙹󱋏󵉐󱬽󷸽󲘝󹄾󷦴󳰭󱁞󳃵󱁞󵀛󵒹󱋏󵉐󱬽󸓑󱑍󳍈
󳧊󳥫󱔊󰶦󲳲󸡿󷠴󰵷󴃼󵟂󱜴󶡋󲘌󶩞󷩙󵉐󵉐󱐂󳃵󴦡󴧈󹑦󹀘
󲳴󹏣󵰩󱙱󲘝󲦻󳌁󱳂󵒹󵉐󴙃󶑂󰹝󵉌󱑗󸔤󱥂󳥫󱔊󰻀󵀛󳃵󵾬󰽄󵒹
󱝗󳭕󰺄󱟘󸑴󷝥󳥀󳌄󰻅󸿉󴃻󲔞󱌍󹁨󲹗
󴕢󴏈󱑹󼵼󷸽󱋔󳜘󲮔󱋏󵉐󱬽󱠥󳏄󲫡󵒹󸑷󳍺󼵼󰻅󸿮󰽜󷩙󵉐󹑦󹀘
󱜌󱐁󵉐󴋒󶑇󰵷󰼕󸿮󰽜󴃽󹑦󹀘
󱐘󱖢󲘝󰶚󰶢󱋏󵉐󱬽󸑷󳍺󱲉󰵨󸁱
󱋏󵉐󱬽󳟾󰶺
220 V
󵒹󳫼󱎦󲕼󵈾󵉐󴙃󶙝󷸄󷷧󷸽󱖢󷸛󱱄󱲉󰻤󰽧
󱌧󰺮󵉐󱚔󰵵󰾫󵈾󱋏󵉐󱬽󴃽󷨟󱐮󰵷󸓔󵈾󰸶󸎩󸏀󱋏󵉐󱬽
󰶺󵉐󴋒󱋏󵉐󼵸󱱄
B
󼵹
1.
󳙟󸑴󵉐󴋒󶑇󱑹󼵼󱋔󲘝󱋏󵉐󱬽󵒹󳏄󱿣󳏄󱑍󵕲󲪿󵒹󵉐󴙃󳏄󲫡󰵴
2.
󲘝󵉐󴋒󶑇
1
󳏄 󱌇 󱑍 󱋏 󵉐 󱬽 󰶦 󼵼󵟂 󲕂 󵉐 󴋒 󶑇 󲔥 󱌍 󲙡 󰽚 󶐥 󶮁
󽵈󱋏󵉐󰶦󽵉
󳉸󵤚󴦨󲘝󰵷󳜘󸽹󴩍󼵼󷞎󵤚󱋏󵉐󸑃󵪑󲦻󶑒󲮔󲄥
14
简体中文
6
󵶎󰽥󰶦󳛓
3.
󶐥󶮁󴦨󳉰󶑰󰹮󸁱󷞎󵤚󱋏󵉐󲔥󳃮󴃽󳞟󵉐󴋒󶑇󲦻󲔥󱌍󱋏󵉐󼵼󲹡󱜴
󰻅󰾫󵈾󵉐󴋒󶑇󳃵󲘝󵉐󴋒󶑇󵊇󱲉󱋏󵉐󱬽󰵴󷦴󰺣󱋏󵉐󱬽󰵴󱜌󰵵
󵉐󴋒󶑇󼵼󷸽󳉾󰵵󵉐󴋒󶑇󰵴󵒹󵉐󴋒󸡻󳙟󳉾󸷶
2
󴎥󽴼󰶺󰸬󵟂󱁃󸹋󵨍󲒪󵉐󴋒󵒹󳙫󶡋󱠥󰾫󵈾󲘒󱠑󳥓󱿑󱗋󼵼󱲉󹗸󴂄󰾫󵈾
󵉐󴋒󶑇󰷔󱑹󲳴󹏣󲘝󱌧󲔥󱌍󱋏󵉐
󱋏󵉐󱬽󳕽󰽳
󱌣󰸶󵉐󴋒󶑇󵒹󱋏󵉐󴸑󲵗󼵼󷸽󱛭󸾔󰻅󰵵󳉸󵤚󴦨󷸺󳟉
󱋏󵉐󴸑󲵗󳉸󵤚󴦨
󱋏󵉐󰶦
󲦻󲔥󱌍󱋏󵉐
󴪛󱎈󵉐󴋒󶑇󲮂󸑸
*
*
󶐥󶮁󳉸󵤚󴦨󰼕󶑪󶑰󸽹󴩍󼵼󰽏󹺖󶮁󳉸󵤚󴦨󱲉󳦦󴂄󳕽󰽳󸑃󵪑󰶦󰼕󰹮
󸁱󵉐󴋒󶑇󸐫󱑍󸓔󲰳󴖜󲫟󱝠󼵼󹺖󶮁󳉸󵤚󴦨󰼕󴯇󴦤󼵼󱋏󵉐󱬽󲘝󲷫󱾖
󱋏󵉐󵪑󲪹
󴃽󱌰󲖃󱋏󵉐󱬽󰵷󶡋󰶺󳙧󹁼󵒹󵉐󴋒󶑇󱋏󵉐󱋏󵉐󱬽󳉸󵤚󴦨󰵷󰹮󳞟󷞎
󵤚󵉐󴋒󳥤󳙧󹁼
󴎥󽴼󸑰󰷳󱜴󶡋󲼒󱠃󱋏󵉐󱬽󳥤󳙧󹁼
󲁶󳩔󱋏󵉐󱬽󳏀󵤚󲒹󱲉󳙧󹁼󼵼󷸽󲘝󱋏󵉐󱬽󱠥󵉐󴋒󶑇󸓑󱑍󳍈󳧊󵒹󶑷󱁞
󰶦󲳲󸑴󷝥󴐶󷸛
󴪛󱎈󵉐󴋒󶑇󲮂󸑸
󲰳󱋏󵉐󱬽󳰭󴐶󱑍󵉐󴋒󶑇󸑃󴪛󳃵󸑃󱎈󳞟󼵼󲔑󰼕󶩉󱔔󱞘󱔔󴪛
/
󱎈󵉐󴋒
󲮂󸑸󳺸󲮮󼵼󳡾󱄣󱋏󵉐󼵼󵕭󱑍󵉐󴋒󶑇󸐫󱑍󸓔󲰳󵒹󴖜󲫟󴬭󱝠󼵼󱋏󵉐󱬽
󰼕󶩉󱔔󱐘󳌄󱑍󵉐󴋒󶑇󱋏󵉐󳺸󲮮󴃽󱔇󶡋󱜴󵟂󱁃󵉐󴋒󶑇󳉇󳥤󳥓󸻌󵒹
󰾫󵈾󲘒󱠑
󱎈󵉐󴋒󶑇󱋏󵉐󸔠󲫟󴇲󴪛󵉐󴋒󶑇󱋏󵉐󸔠󲫟󲾩󵉐󴋒󶑇󱲉󳚯󰶢󱋏󵉐
󱟰󳦎󵒹󱋏󵉐󸔠󲫟󸛫󰼕󸏆󲾩󼵼󱙱󰾫󵉐󴋒󶑇󱘯󴖜󰷳󰵷󰼕󲷫󱾖󱑍󳥓󱿑
󸔠󲫟
󵉐󲒪󱁃󳇢󶂺󶑢
XR
󸹋󵨍󲒪󵉐󴋒󲦩󱌩󱌩󳥤󵉐󲒪󱁃󳇢󶂺󶑢󷸄󷷧󼵼󱜴󱁃󳇢󵉐󴋒󶑇󱋞󱜍󸑃
󸏀󸑃󴪛󳃵󸑃󲫟󳙟󵉐󰷔󲕳
󲁶󳩔󵉐󲒪󱁃󳇢󶂺󶑢󱾆󰸶󸑙󰽳󴸑󲵗󼵼󷸫󲦩󱌩󲘝󶩉󱔔󱄣󴃻󳕽󰽳󲁶󳩔󱜅
󵈱󸑰󵨬󲺕󱎄󼵼󷸽󲘝󸹋󵨍󲒪󵉐󴋒󶑇󳙟󱲉󱋏󵉐󱬽󰵴󼵼󵕭󶩜󱌧󲔥󱌍󱋏󵉐
󱼘󳉲󲮮󲔞󷠴
󸑰󰹉󱋏󵉐󱬽󷸄󷷧󰶺󱜴󰻅󲔞󷠴󱲉󱻗󰵴󼵼󰷳󱜴󰻅󵕭󵰩󱲉󳭲󹈘󳃵󲦩󰽳󱜶
󹈘󰵴󲁶󳩔󲔞󷠴󱲉󱻗󰵴󼵼󷸽󵟂󱁃󱋏󵉐󱬽󵒹󰽚󶔩󱜴󰻅󸑷󳍺󱑍󵉐󴙃󳏄
󲫡󼵼󲪈󰶃󸑵󵨍󱻗󷨮󳃵󱌧󰺮󱜴󶡋󲃏󵟰󵭠󴉟󴐩󸔒󵒹󹁼󵟰󴶠󲘝󱋏󵉐󱬽󶟝
󹈘󰽳󰶺󱲉󱻗󰵴󲔞󷠴󷙡󰶐󵒹󰽚󶔩󳺸󳨤󰾫󵈾󶩜󲘲
25
4
󴈘󵾜󸻌󷙡󰶐
󲨩󵕭󲲉󶩜󲘲
7-9
󴈘󵾜󵒹󵜗󶦂󳨤󷙡󰶐󼵸󱙁󴹞󸀞󰸉󼵹󴶗󴶗󱱀󲕂󱋏󵉐󱬽󼵼
󲘝󷙡󰶐󳥓󱿑󸿴󲫟󸷑󱌇󳦡󳧟󼵼󹏬󵊇󶐩
5
5
󴈘󵾜󹆫󱲉󱻗󱾫󲘝󱋏󵉐󱬽󶟝
󹈘󵒹󲔞󷠴󳹶󲘇󱎦󹆫󱐁󵒹󷙡󰶐󼵼󲔥󱌍󳙟󶔩󱑍󰽚
󱋏󵉐󱬽󴕢󴏈󷸺󳟉
󷵪󱟈󽴼󷩙󵉐󱙮󹀘󴕢󴏈󱑹󼵼󷸽󲘝󱋏󵉐󱬽󰺣󰹝󴐩󵉐󴙃󳏄󲫡
󰵴󳈭󰵵󱜴󵈾󲧓󳃵󹈌󸢅󲚪󸎲󱑙󴕢󹀒󱋏󵉐󱬽󱾫󸛉󵒹󴋔󱴼󱠥
󴍙󶡓󷸽󱖢󰾫󵈾󴊑󳃵󰻤󰽧󴕢󴏈󱑬󱐘󱖢󷷯󰻤󰽧󴓋󰽥󴕸󱌇
󲦩󱌩󼵼󱐘󱖢󷷯󲦩󱌩󵒹󰻤󰽧󸛉󰻞󴑶󱲉󴓋󰽥󰶦
󵉐󴋒󶑇
󸷐󲘇󳄿󳥤󵉐󴋒󶑇󵒹󸡿󷦴󲔞󱌍󷸺󳟉
󱲉󷷨󸀞󳥀󳌄󵉐󴋒󶑇󳞟󼵼󷸽󱔊󲳴󸿢󰵴󵕢󲰷󱴘󱝀󱠥󵉐󱚔
󱖬󷠴󵷳󱌼󵒹󵉐󴋒󶑇󲪈󳦣󲔥󱌍󱋏󵉐󰾫󵈾󵉐󴋒󶑇󱠥󱋏󵉐󱬽󰷔󱑹󼵼󷸽󸾔
󷹁󰵵󱐪󲔞󱌍󳉸󵤚󼵼󴬭󱝠󸗾󲳅󳄿󸒤󵒹󱋏󵉐󵪑󲪹
󷸽󸾔󷹁󳄿󳥤󷸺󳟉
󷸽󱖢󱲉󳟓󴳙󴾡󱺰󼵼󲁶󳥤󳟓󴱎󴓋󰽥󴉟󰽥󳃵󵿌󲘾󵒹󴾡󱺰󰶦󱋏󵉐
󳃵󰾫󵈾󵉐󴋒󱲉󱋏󵉐󱬽󰶦󳏄󱌇󳃵󱜌󱐁󵉐󴋒󳞟󱜴󶡋󰼕󴩀󴱎󵿌󲘾
󳃵󴉟󰽥
󱐘󱖢󲰃󷝥󲘝󵉐󴋒󳙟󸑴󱋏󵉐󱬽󷸽󱖢󰻅󰻤󰽧󳜱󲮮󳙗󷠴󵉐󴋒󶑇󰻅
󱲉󰵷󵕲󲖃󵒹󱋏󵉐󱬽󰶦󰾫󵈾󼵼󱞅󱐮󵉐󴋒󶑇󱜴󶡋󰼕󵝷󷠭󼵼󲘌󶩞󰶛
󸡿󰺄󸉨󰼠󲕳
󱜬󰾫󵈾
DeWALT
󱋏󵉐󱬽󰶺󵉐󴋒󶑇󱋏󵉐
󷸽󱖢󱨃󴘲󵉐󴋒󶑇󳃵󲘝󱌧󴑶󴎚󱲉󴊑󳃵󱌧󰺮󴓋󰽥󰶦
󷸽󱖢󱲉󴖜󲫟󱜴󶡋󸐫󱑍󳃵󸂅󸑃
40
°
C
104
°
F
󵒹 󱲒 󳜱󼵸 󲁶 󱾚 󱿕
󳄫󱾫󵒹󳱠󲒪󳃵󸢅󲚪󲮋󵴱󴶠󰶦󼵹󲒹󱆱󳃵󰾫󵈾󲦩󱌩󱠥󵉐󴋒󶑇
󱙱󰾫󵉐󴋒󶑇󰶛󸡿󱜍󳌁󳃵󲔥󱌍󳌁󱳂󼵼󰷳󷸽󱖢󴫰󱗋󵉐󴋒󶑇󵉐󴋒
󶑇󱲉󴦡󰶦󰼕󱜅󵈱󴳙󴨾󸹋󵨍󲒪󵉐󴋒󶑇󱲉󴱎󴪕󳞟󰼕󸡻󳙟󳥤󴇬󴪇
󹄻󱠥󴶠󸀙
󲁶󳩔󵉐󴋒󴓋󰽥󳍺󷩙󱑍󵓽󶞍󼵼󷸽󵰩󱙱󰻅󰶦󲶎󶞎󵒶󱠥󴕢󴊑󱍿󴏥󳍺
󷩙󵒹󱲒󳜱󲁶󳩔󵉐󴋒󴓋󰽥󰵷󲾇󸑴󱌇󵗛󵘌󼵼󲪿󵗣󲮔󵗛󵘌󲪈󵈾󴕢
󴊑󱍿󴏥󶩜󲘲
15
󱐕󸷧󳃵󵕭󱑍󱑟󴡩󲼮󴒋󱿠󲁶󳩔󹄾󷦴󱘖󵋬󳙺󱔕󼵼
󷸽󱟈󵛽󱘖󳇢󰺄󱟘󵉐󴋒󵉐󷩓󸀙󵉌󴓋󴸑󳥤󳦽󵠬󸟒󵔯󱠥󸹋󵔯󵒹󴕋
󱝗󴶠󶑇󳃮
󲦻󳅨󲮔󵉐󴋒󵒹󱌼󸛉󴶠󸀙󱜴󶡋󲘌󶩞󱠏󱞩󸖥󱑟󴡩󷸽󱁃󳉰󵭠󴉟
󴐩󸔒󲁶󳩔󵍀󴸑󳉰󶑰󲒹󱲉󼵼󷸽󲙡󱘖
󷵪󱟈󽴼󴧃󰼠󱙮󹀘󵉐󴋒󴓋󲁶󳩔󳍺󷩙󱑍󴦡󶰅󳃵󴦡󴬟󱜴󶡋󰼕
󴱎󴪕
󷵪󱟈󽴼󱐘󱖢󰻅󰻤󰽧󵀛󵉌󷸛󱱄󳅨󲮔󵉐󴋒󶑇󵉐󴋒󶑇󱾫󱽳󵝷󷠭
󳃵󳌁󱳂󳞟󼵼󷸽󱖢󲘝󵉐󴋒󶑇󳏄󱌇󱋏󵉐󱬽󷸽󱖢󳊦󱚔󳍉󶽆󳃵
󳌁󱳂󵉐󴋒󶑇󷸽󱖢󰾫󵈾󱜍󸑃󲰃󴩙󸡿󱐂󳍉󶽆󵠾󱚔󳃵󰻅󰻤
󰽧 󱌧 󲔑 󳜱 󲮮󼵸 󲁶 󷠅 󸷑 󲒪 󵭭 󵝷 󱜍 󱑍 󸹭 󲒪 󵒹 󸡿 󱐂 󸅵 󸅏 󼵹󱜍
󳌁󵒹󵉐󴋒󶑇󳃵󱋏󵉐󱬽󱞅󱐮󱜴󶡋󰼕󲮹󸁱󷩙󵉐󳃵󵉐󱐂󳌁󱳂
󵒹󵉐󴋒󶑇󲪿󸓑󱰑󶑷󱁞󰶦󲳲󸑴󷝥󱰑󳙑
󷵪󱟈󽴼󴦡󴧈󱙮󹀘󷸽󱖢󱲉󲒹󱆱󳃵󳑦󸑙󵉐󴋒󶑇󳞟󷷯󸢅󲚪󴶠󱡸
󳍺󷩙󳣑󹆫󵒹󵉐󴋒󰶚󳨨󰾿 󲁶 󼵼󷸽 󱖢 󲘝 󵉐 󴋒 󶑇 󳙟 󱲉 󱰶 󷡞 󱜢
󷟎󲦩󱌩󵔲󰹢󱡸󲀜󰻞󵔲󳈅󲚈󵴞󱜴󶡋󰵹󳚕󸷑󷙡󰶐󸷭󱗑
󵴞󴶠󱡸󳍺󷩙󵒹󱲒󳜱
󷵪󵤚󽴼󰵷󵈾󳞟󼵼󲘝󲦩󱌩󰿪󳙟󱲉󲪃󵫙󵒹󷞎󹈘󰵴󼵼󵟂󱁃󰵷󰼕󳥤
󸅬󶑍󳃵󳍉󶽆󵒹󱙮󹀘󰵨󰹉󱌩󳥤󱿑󱴘󵉐󴋒󶑇󵒹󲦩󱌩󱜴󰻅󵕭󵰩
󰽏󱜴󶡋󰼕󸎾󳟓󷠅󳔮󱂞
󸑙󸏖
󷵪󱟈󽴼󴦡󴧈󱙮󹀘󵉐󴋒󸑙󸏖󸔁󰶦󼵼󲁶󳩔󵉐󴋒󰶚󳨨󲼒󱾫󳍺󷩙
󲘌󵉐󳧟󳛲󼵼󱜴󶡋󰼕󲮹󱜅󴦡󴧈󸑙󸏖󵉐󴋒󳞟󼵼󷸽󱔊󲳴󱁃󳇢󵉐
󴋒󰶚󳨨󼵼󵟂󱁃󰵹󱜴󶡋󳍺󷩙󵉐󴋒󲘌󶩞󵜋󸄠󵒹󳧟󳛲󶭼󲁪󶑠󶒛
󴎥󽴼󸹋󵨍󲒪󵉐󴋒󰵷󲪿󳙟󱲉󳅰󸑙󷝥󳧛󰶦
DeWALT
󵉐󴋒󵳘󱝗󳄿󳥤󸓔󵈾󵒹󷝥󰶍󱠥󴎂󲲓󳫼󱎦󷨟󲕂󵒹󸑙󸏖󷨟󶲵󼵼
󱖬󳉎󶛬󱝗󱱃󱙮󹀘󱡸󸑙󸏖󲮋󷷴󷨟󵱏󶲵󳦦
UN Recommendations
on the Transport of Dangerous Goods
󱱃󸿣󶫕󵭠󸑙󸏖󱘹󰼕
IATA
󱙮󹀘󱡸󷨟󱐮
International Air Transport Association
IATA
Dangerous Goods Regulations
 󱱃 󸿣 󴑴 󸑙 󱙮 󹀘 󱡸
IMDG
󷨟󱐮
International Maritime Dangerous Goods
IMDG
Regulations
󱠥󴂎󴐎󱙮󹀘󸀘󴶠󱱃󸿣󱌗󸄠󸑙󸏖󱘹󲕂
European Agreement
Concerning The International Carriage of Dangerous Goods by
7
󵶎󰽥󰶦󳛓
Road
ADR
󸹋󵨍󲒪󵉐󴋒󱠥󵉐󴋒󶑇󲦻󸗾󲳅󶛬󱝗󱱃󱙮󹀘󱡸󸑙󸏖󲮋
󷷴 󷨟 󵱏 󶲵 󳦦 󳅜 󱍄 󵳧
38
3
󶮝󱌣󰸶󴐶󷸛󱠥󳫼󱎦󵒹󷸺󳟉󸔒󸑃󴐶󷸛
󱿑 󱾵 󳚩 󲺕 󱎄 󰵵 󼵼󱜅 󸑙
DeWALT
󵉐󴋒󶑇󰵷󲚪󰸶󲔥󱌍󵷘󱑗󵒹
9
󵾬󱙮
󹀘󱡸󸔒󲨣󲺕󱎄󰵵󼵼󱜬󳥤󲰳󸑙󸏖󱖬󱞏󰵨󰶢󶡋󸢁󵴞󶐪󱿑󰸶
100
󵆳󳞟
Wh
󵒹󸹋󵨍󲒪󵉐󴋒󳞟󼵼󳅟󹄾󷦴󰽳󰶺󲔥󱌍󵷘󱑗󵒹
9
󵾬󱙮󹀘󱡸󱜅󸑙
󳄿󳥤󸹋󵨍󲒪󵉐󴋒󱾫󱽳󰵴󱲳󳫼󴎥󳥤󵆳󳞟󵴞󶐪󴃽󱾫󼵼󵉌󰸶󴎂󷨟󴇲󸏆
󱾖 󳧈 󼵼󳝾 󷸀 󵆳 󳞟 󵴞 󶐪 󳟾 󱾵 󲘲 󼵼
DeWALT
󸛫󰵷󲮋󷷴󱙁󴹞󵭠󸑙󸹋󵨍󲒪󵉐
󴋒󶑇󱜅󸑙󱖬󱞏󵉐󴋒󵒹󲦩󱌩󼵸󶑇󱝗󲀜󰻞󼵹󳞟󼵼󲁶󳩔󵉐󴋒󶑇󵒹󹐅󲕂󶡋
󸢁󰵷󱿑󰸶
100
󵆳󳞟
Wh
 󼵼󱐮 󱜴 󰻅 󵭠 󸑙
󳝾󷸀󱜅󸑙󳟾󱞅󶐶󱌇󲔥󱌍󵷘󱑗󶲵󱰶󱌼󼵼󸑙󸏖󱌗󱝁󱲳󳥤󸀔󰻤󸗾󲳅󳥓󳜞
󴎂󷨟󰶦󱌣󰸶󱖬󷠴󳫼󵶋
/
󳫼󷷶󱠥󱙁󳌙󵒹󷦴󴊡
󳦦󳅜󱍄󳦦󶮝󵒹󱁍󲸃󳟾󱐁󰸶󱦥󲼒󳏀󰿙󼵼󰶃󷷪󰶺󱲉󶒙󱑗󳛓󳮔󳞟󱎦󵟂󳝾
󷸵󰽏󳟾󰵷󳏀󰿙󳟉󵤚󳃵󳢞󵤚󵒹󳈑󱁃󸀞󰸉󳜱󸀐󳥤󵟂󱁃󱌧󷝥󰶺󸗾󲔜
󸓔󵈾󴎂󷨟󵒹󸀔󰻤
󲒹 󳙟 󲮋 󷷴
1.
󳥓󲁪󲘝󵉐󴋒󲒹󳙟󱲉󸿋󱎬󲪂󴲖󸑵󵨍󸿊󱋖󵕭󲘙󰵷󰼕󸑃󴪛󳃵󸑃
󱎈󵒹󱲒󳜱󰶺󰸬󶸧󲲥󳥓󰾖󵒹󵉐󴋒󲶎󶡋󱠥󰾫󵈾󲘒󱠑󼵼󷸽󲹡󱲉󰵷󰾫
󵈾󵉐󴋒󶑇󳞟󲘝󱌧󲒹󱆱󱲉󲕕󴖜󰵵
2.
󸻌󳦎󲒹󱆱󳞟󼵼󲮋󷷴󲘝󲔥󱌍󱋏󵉐󵒹󵉐󴋒󶑇󰺣󱋏󵉐󱬽󱜌󱐁󼵼󲒹󱆱󱲉
󸿋󱎬󲪂󴲖󵒹󱲒󳜱󼵼󰻅󸐫󱑍󳥓󰾖󳙫󳩔
󴎥󽴼󵉐󴋒󶑇󰵷󲪿󱲉󵉐󴋒󲦻󲔥󱌍󶙳󲙵󵒹󴸑󲵗󰵵󲒹󳙟󰾫󵈾󵉐󴋒󶑇󰷔
󱑹 󼵼󲳴 󹏣 󸡿 󳜞 󰶺 󵉐 󴋒 󶑇 󱋏 󵉐
󱋏󵉐󱬽󱠥󵉐󴋒󶑇󰵴󵒹󳫼󵶋
󹀒󰸬󱲉󳦦󳅜󱍄󰶦󳄿󰾫󵈾󵒹󳫼󲴌󼵼󱋏󵉐󱬽󱠥󵉐󴋒󶑇󵒹󳫼󵶋󸑯󱖬󳉎󽴼
󰾫󵈾󱑹󷸽󸾔󷹁󰾫󵈾󳅜󱍄
󷦴 󰸬 󷩓 󱋏 󵉐 󳞟 󸾃 󼵼󷸽 󱛭 󸾔
󳆯󳦪󱛭󳚩
󷸽󱖢󰾫󵈾󲘌󵉐󴶠󰽥󳄤󱑟
󷸽󱖢󲘇󳌁󱳂󵒹󵉐󴋒󶑇󱋏󵉐
󷸽󱖢󲘝󱌧󳣑󹆫󰸶󴊑󰶦
󲪿󵰩󱙱󳥀󳌄󳥤󶓄󹀵󵒹󵉐󶑂
󷸽󱜬󱲉
4 °C
󱠥
40 °C
󰷔󸾃󵒹󴖜󲫟󰵵󱋏󵉐
󱜬󶡋󱲉󲕕󱌼󰾫󵈾
󲮚󶔩󵉐󴋒󶑇󳞟󼵼󷸽󲃇󱦥󱾆󵀛󰻅󱁃󳇢󳃯󰻍󵒹󴾡󱺰
󱜬󰾫󵈾󳉸󲕂󵒹
DeWALT
󱋏󵉐󱬽󰶺
DeWALT
󵉐󴋒󶑇
󱋏 󵉐 󰾫 󵈾
DeWALT
󱋏󵉐󱬽󰶺󹈌
DeWALT
󵉐󴋒󱋏󵉐
󱜴󶡋󰼕󲘌󶩞󵉐󴋒󴳙󴨾󳃵󱐁󴾢󱌧󰺮󱙮󹀘󲺕󱎄
󷸽󱖢󴫰󱗋󵉐󴋒󶑇
󵉐󴋒󵾬󱴘
DCD701
󰾫󵈾
12
󰼄󴶶󵉐󴋒󶑇
󸑰󰹉󵉐󴋒󶑇󱜴󵈾󰸶󽴼
DCB122
DCB124
DCB125
DCB127
󳥀 󱾵 󱁍
󲸃 󼵼󷸽 󱛭 󸾔
󳆯󳦪󱛭󳚩
󱖬󷠴󱌼󵒹󴶠󱡸
󱖬󷠴󱌼󵒹󴶠󱡸󱖬󳉎󽴼
1
󱜬
󵉐󸸃
/
󸁱󲒪
1
󰶢
󱋏󵉐󱬽
1
󰶢
󵓽 󲨅 󳅿󼵸 󸛉 󱐕 󱴘 󱝀 󱌼 󶩉 󲨅 󼵹
1
󰶢
󸹋 󵨍 󲒪 󵉐 󴋒 󶑇󼵸
C1
󼵼
D1
󼵼
L1
󳺸󱴘󼵹
2
󰶢
󸹋 󵨍 󲒪 󵉐 󴋒 󶑇󼵸
C2
󼵼
D2
󼵼
L2
󳺸󱴘󼵹
3
󰶢
󸹋 󵨍 󲒪 󵉐 󴋒 󶑇󼵸
C3
󼵼
D3
󼵼
L3
󳺸󱴘󼵹
1
󳦦
󷸺󳟉󳅜󱍄
󴎥󽴼
N
󱴘󱝀󰵷󱖬󳉎󵉐󴋒󶑇󱋏󵉐󱬽󱠥󲦩󱌩󵷳
NT
󱴘󱝀󰵷󱖬󳉎󵉐󴋒
󶑇󱠥󱋏󵉐󱬽
󴎥󽴼󱥂󳫼󱠥󱥂󱡸󱝝󵩧󲰲󱌧󱝑󶩉󳄿󳥤󶙐󳄿󳥤
󳰭󳫆󲦩󱌩󸛉󰻞󳃵󸿢󰻞󳟾󱞅󱲉󸑙󸏖󸑃󵪑󰶦󳌁󱳂
󳕽 󰽳 󱑹 󼵼󷸽 󳈅 󵭠 󰺬 󶑉 󸾔 󷹁 󲪈 󳍎 󳏤 󳦦 󳅜 󱍄
󲦩󱌩󰵴󵒹󳫼󷷶
󲦩󱌩󰵴󱙫󳥤󰵵󱐪󱱄󲱏󽴼
󰾫󵈾󱑹󷸽󸾔󷹁󰾫󵈾󳅜󱍄
󷸽󰾇󳄦󱞒󱔃󱁃󳇢󱬽
󷸽󰾇󳄦󳇢󵕢󷠴󱾋
󱜴󷨜󸏓󲘙󱐘󱖢󵕭󷨡󴡩󱋖󳧳
󳞉 󳦎 󰻀 󵜧 󰽚 󶔩󼵸 󱱄
A
󼵹
󱖬󱞏󱑗󸔤󲪄󰻨󵒹󳞉󳦎󵜧
13
󳅨󱙫󱲉󲦩󱌩󱾫󱽳󰵴
󵤚󰾿󽴼
2019 XX XX
󱑗󸔤󲪄󰻨
󷸺 󳟉󼵸 󱱄
A
󼵹
󷵪󱟈󽴼󱐘󱖢󳙗󷠴󳦦󵉐󱔔󲦩󱌩󳃵󱌧󰻤󰽧󸛉󰻞󼵼󱞅󱐮󱜴󶡋󰼕󲘌
󶩞󳌁󱳂󳃵󰺄󸉨󰼠󲕳
1
󵉐󴋒󶑇
2
󵉐󴋒󶑇󸡻󳙟󳉾󸷶
3
󰶻󳅜󳪒
4
󱜎󸔠󷩙󱜅󲮔󱌣
5
󴃼󱜀󸎯󳍾󱑗󳉾󸷶
6
󳺸󲮮󸓦󳉋󴾡
7
󸎯󸔠󸓦󳉋󱬽
8
󲦩󰽳󴦨
9
󱿫󱿣󲀜󵷘
10
󳝾󸹊󱗑󱿫󱿣
15
简体中文
7
󵶎󰽥󰶦󳛓
Road
ADR
󸹋󵨍󲒪󵉐󴋒󱠥󵉐󴋒󶑇󲦻󸗾󲳅󶛬󱝗󱱃󱙮󹀘󱡸󸑙󸏖󲮋
󷷴 󷨟 󵱏 󶲵 󳦦 󳅜 󱍄 󵳧
38
3
󶮝󱌣󰸶󴐶󷸛󱠥󳫼󱎦󵒹󷸺󳟉󸔒󸑃󴐶󷸛
󱿑 󱾵 󳚩 󲺕 󱎄 󰵵 󼵼󱜅 󸑙
DeWALT
󵉐󴋒󶑇󰵷󲚪󰸶󲔥󱌍󵷘󱑗󵒹
9
󵾬󱙮
󹀘󱡸󸔒󲨣󲺕󱎄󰵵󼵼󱜬󳥤󲰳󸑙󸏖󱖬󱞏󰵨󰶢󶡋󸢁󵴞󶐪󱿑󰸶
100
󵆳󳞟
Wh
󵒹󸹋󵨍󲒪󵉐󴋒󳞟󼵼󳅟󹄾󷦴󰽳󰶺󲔥󱌍󵷘󱑗󵒹
9
󵾬󱙮󹀘󱡸󱜅󸑙
󳄿󳥤󸹋󵨍󲒪󵉐󴋒󱾫󱽳󰵴󱲳󳫼󴎥󳥤󵆳󳞟󵴞󶐪󴃽󱾫󼵼󵉌󰸶󴎂󷨟󴇲󸏆
󱾖 󳧈 󼵼󳝾 󷸀 󵆳 󳞟 󵴞 󶐪 󳟾 󱾵 󲘲 󼵼
DeWALT
󸛫󰵷󲮋󷷴󱙁󴹞󵭠󸑙󸹋󵨍󲒪󵉐
󴋒󶑇󱜅󸑙󱖬󱞏󵉐󴋒󵒹󲦩󱌩󼵸󶑇󱝗󲀜󰻞󼵹󳞟󼵼󲁶󳩔󵉐󴋒󶑇󵒹󹐅󲕂󶡋
󸢁󰵷󱿑󰸶
100
󵆳󳞟
Wh
 󼵼󱐮 󱜴 󰻅 󵭠 󸑙
󳝾󷸀󱜅󸑙󳟾󱞅󶐶󱌇󲔥󱌍󵷘󱑗󶲵󱰶󱌼󼵼󸑙󸏖󱌗󱝁󱲳󳥤󸀔󰻤󸗾󲳅󳥓󳜞
󴎂󷨟󰶦󱌣󰸶󱖬󷠴󳫼󵶋
/
󳫼󷷶󱠥󱙁󳌙󵒹󷦴󴊡
󳦦󳅜󱍄󳦦󶮝󵒹󱁍󲸃󳟾󱐁󰸶󱦥󲼒󳏀󰿙󼵼󰶃󷷪󰶺󱲉󶒙󱑗󳛓󳮔󳞟󱎦󵟂󳝾
󷸵󰽏󳟾󰵷󳏀󰿙󳟉󵤚󳃵󳢞󵤚󵒹󳈑󱁃󸀞󰸉󳜱󸀐󳥤󵟂󱁃󱌧󷝥󰶺󸗾󲔜
󸓔󵈾󴎂󷨟󵒹󸀔󰻤
󲒹 󳙟 󲮋 󷷴
1.
󳥓󲁪󲘝󵉐󴋒󲒹󳙟󱲉󸿋󱎬󲪂󴲖󸑵󵨍󸿊󱋖󵕭󲘙󰵷󰼕󸑃󴪛󳃵󸑃
󱎈󵒹󱲒󳜱󰶺󰸬󶸧󲲥󳥓󰾖󵒹󵉐󴋒󲶎󶡋󱠥󰾫󵈾󲘒󱠑󼵼󷸽󲹡󱲉󰵷󰾫
󵈾󵉐󴋒󶑇󳞟󲘝󱌧󲒹󱆱󱲉󲕕󴖜󰵵
2.
󸻌󳦎󲒹󱆱󳞟󼵼󲮋󷷴󲘝󲔥󱌍󱋏󵉐󵒹󵉐󴋒󶑇󰺣󱋏󵉐󱬽󱜌󱐁󼵼󲒹󱆱󱲉
󸿋󱎬󲪂󴲖󵒹󱲒󳜱󼵼󰻅󸐫󱑍󳥓󰾖󳙫󳩔
󴎥󽴼󵉐󴋒󶑇󰵷󲪿󱲉󵉐󴋒󲦻󲔥󱌍󶙳󲙵󵒹󴸑󲵗󰵵󲒹󳙟󰾫󵈾󵉐󴋒󶑇󰷔
󱑹 󼵼󲳴 󹏣 󸡿 󳜞 󰶺 󵉐 󴋒 󶑇 󱋏 󵉐
󱋏󵉐󱬽󱠥󵉐󴋒󶑇󰵴󵒹󳫼󵶋
󹀒󰸬󱲉󳦦󳅜󱍄󰶦󳄿󰾫󵈾󵒹󳫼󲴌󼵼󱋏󵉐󱬽󱠥󵉐󴋒󶑇󵒹󳫼󵶋󸑯󱖬󳉎󽴼
󰾫󵈾󱑹󷸽󸾔󷹁󰾫󵈾󳅜󱍄
󷦴 󰸬 󷩓 󱋏 󵉐 󳞟 󸾃 󼵼󷸽 󱛭 󸾔
󳆯󳦪󱛭󳚩
󷸽󱖢󰾫󵈾󲘌󵉐󴶠󰽥󳄤󱑟
󷸽󱖢󲘇󳌁󱳂󵒹󵉐󴋒󶑇󱋏󵉐
󷸽󱖢󲘝󱌧󳣑󹆫󰸶󴊑󰶦
󲪿󵰩󱙱󳥀󳌄󳥤󶓄󹀵󵒹󵉐󶑂
󷸽󱜬󱲉
4 °C
󱠥
40 °C
󰷔󸾃󵒹󴖜󲫟󰵵󱋏󵉐
󱜬󶡋󱲉󲕕󱌼󰾫󵈾
󲮚󶔩󵉐󴋒󶑇󳞟󼵼󷸽󲃇󱦥󱾆󵀛󰻅󱁃󳇢󳃯󰻍󵒹󴾡󱺰
󱜬󰾫󵈾󳉸󲕂󵒹
DeWALT
󱋏󵉐󱬽󰶺
DeWALT
󵉐󴋒󶑇
󱋏 󵉐 󰾫 󵈾
DeWALT
󱋏󵉐󱬽󰶺󹈌
DeWALT
󵉐󴋒󱋏󵉐
󱜴󶡋󰼕󲘌󶩞󵉐󴋒󴳙󴨾󳃵󱐁󴾢󱌧󰺮󱙮󹀘󲺕󱎄
󷸽󱖢󴫰󱗋󵉐󴋒󶑇
󵉐󴋒󵾬󱴘
DCD701
󰾫󵈾
12
󰼄󴶶󵉐󴋒󶑇
󸑰󰹉󵉐󴋒󶑇󱜴󵈾󰸶󽴼
DCB122
DCB124
DCB125
DCB127
󳥀 󱾵 󱁍
󲸃 󼵼󷸽 󱛭 󸾔
󳆯󳦪󱛭󳚩
󱖬󷠴󱌼󵒹󴶠󱡸
󱖬󷠴󱌼󵒹󴶠󱡸󱖬󳉎󽴼
1
󱜬
󵉐󸸃
/
󸁱󲒪
1
󰶢
󱋏󵉐󱬽
1
󰶢
󵓽 󲨅 󳅿󼵸 󸛉 󱐕 󱴘 󱝀 󱌼 󶩉 󲨅 󼵹
1
󰶢
󸹋 󵨍 󲒪 󵉐 󴋒 󶑇󼵸
C1
󼵼
D1
󼵼
L1
󳺸󱴘󼵹
2
󰶢
󸹋 󵨍 󲒪 󵉐 󴋒 󶑇󼵸
C2
󼵼
D2
󼵼
L2
󳺸󱴘󼵹
3
󰶢
󸹋 󵨍 󲒪 󵉐 󴋒 󶑇󼵸
C3
󼵼
D3
󼵼
L3
󳺸󱴘󼵹
1
󳦦
󷸺󳟉󳅜󱍄
󴎥󽴼
N
󱴘󱝀󰵷󱖬󳉎󵉐󴋒󶑇󱋏󵉐󱬽󱠥󲦩󱌩󵷳
NT
󱴘󱝀󰵷󱖬󳉎󵉐󴋒
󶑇󱠥󱋏󵉐󱬽
󴎥󽴼󱥂󳫼󱠥󱥂󱡸󱝝󵩧󲰲󱌧󱝑󶩉󳄿󳥤󶙐󳄿󳥤
󳰭󳫆󲦩󱌩󸛉󰻞󳃵󸿢󰻞󳟾󱞅󱲉󸑙󸏖󸑃󵪑󰶦󳌁󱳂
󳕽 󰽳 󱑹 󼵼󷸽 󳈅 󵭠 󰺬 󶑉 󸾔 󷹁 󲪈 󳍎 󳏤 󳦦 󳅜 󱍄
󲦩󱌩󰵴󵒹󳫼󷷶
󲦩󱌩󰵴󱙫󳥤󰵵󱐪󱱄󲱏󽴼
󰾫󵈾󱑹󷸽󸾔󷹁󰾫󵈾󳅜󱍄
󷸽󰾇󳄦󱞒󱔃󱁃󳇢󱬽
󷸽󰾇󳄦󳇢󵕢󷠴󱾋
󱜴󷨜󸏓󲘙󱐘󱖢󵕭󷨡󴡩󱋖󳧳
󳞉 󳦎 󰻀 󵜧 󰽚 󶔩󼵸 󱱄
A
󼵹
󱖬󱞏󱑗󸔤󲪄󰻨󵒹󳞉󳦎󵜧
13
󳅨󱙫󱲉󲦩󱌩󱾫󱽳󰵴
󵤚󰾿󽴼
2019 XX XX
󱑗󸔤󲪄󰻨
󷸺 󳟉󼵸 󱱄
A
󼵹
󷵪󱟈󽴼󱐘󱖢󳙗󷠴󳦦󵉐󱔔󲦩󱌩󳃵󱌧󰻤󰽧󸛉󰻞󼵼󱞅󱐮󱜴󶡋󰼕󲘌
󶩞󳌁󱳂󳃵󰺄󸉨󰼠󲕳
1
󵉐󴋒󶑇
2
󵉐󴋒󶑇󸡻󳙟󳉾󸷶
3
󰶻󳅜󳪒
4
󱜎󸔠󷩙󱜅󲮔󱌣
5
󴃼󱜀󸎯󳍾󱑗󳉾󸷶
6
󳺸󲮮󸓦󳉋󴾡
7
󸎯󸔠󸓦󳉋󱬽
8
󲦩󰽳󴦨
9
󱿫󱿣󲀜󵷘
10
󳝾󸹊󱗑󱿫󱿣
16
简体中文
8
󵶎󰽥󰶦󳛓
󷸄󷷧󵈾󸔁
󳦦󵉐󸸃
/
󸁱󲒪󷸄󷷧󵈾󰸶󰶂󰶍󸸃󲒱󱠥󷙡󰶐󲔞󷠴
󷸽󱖢󱲉󴟑󴘫󴾡󱺰󰶦󳃵󱲉󳟓󴱎󴓋󰽥󳃵󴉟󰽥󲒹󱲉󵒹󴾡󱺰󰶦󰾫󵈾󳦦󲦩󱌩
󳦦󵉐󸸃
/
󸁱󲒪󳦽󳟾󰶂󰶍󵒹󵉐󱔔󲦩󱌩
󷸽󱖢󷷯󱋅󵱚󳍺󷩙󳦦󲦩󱌩󶓄󰷙󶑒󹞊󵒹󳕽󰽳󱟘󹄾󷦴󱲉󵔰󵘜󰵵󰾫󵈾
󳦦󲦩󱌩
󱋅󵱚󱠥󰽥󲯴󶙐󱲉󴌶󳥤󰺮󰺄󵔰󵘜󵒹󲺕󱎄󰵵󼵼󱋅󵱚󳃵󰽥󲯴󶙐󰵷󸓔
󲕇󰾫󵈾󳦦󰹢󱡸
󳦦󰹢󱡸󰵷󸓔󱝗󰽥󱔃󲼮󲔾󳃵󳡱󱔃󰵷󸃉󰻅󱛻󶓄󰷙󶑒󹞊󵛽󷸌󳃵󳆯
󶡋󵒹󰺄󱟘󼵸󱖬󳉎󱋅󵱚󼵹󰾫󵈾󼵼󹀒󹈌󰵨󳜿󳥤󶡋󰶺󰺮󰻍󵒹󲔞󱌍󸀐󸀔
󵒹󵔰󵘜󰺄󱟘󰵷󲲥󱲉󳝾󰺄󵔰󵷘󵒹󲺕󱎄󰵵󷷯󱋅󵱚󳍺󷩙󳦦󰹢󱡸
󶑇󷠴󰵹󷹉󳚯
󷵪󱟈󽴼󰶺󸿮󰽜󰶛󸡿󵒹󰺄󸉨󰼠󲕳󹑦󹀘󼵼󱲉󸑴󷝥󰻤󰽧󷹉󳚯󳃵
󱜌󱐁󲔞󷠴󸿢󰻞󳃵󸞂󰻞󰷔󱑹󼵼󷸽󱌣󸽼󲦩󱌩󲪈󳜘󲮔󵉐󴋒󶑇
󸑷󳍺󲼒󱾫󱞘󱔔󱜴󶡋󰼕󲘌󶩞󰺄󸉨󰼠󲕳
󷵪󱟈󽴼󷸽󱜬󰾫󵈾
DeWALT
󵉐󴋒󶑇󱠥󱋏󵉐󱬽
󳏄󱌇󳃵󱜌󱐁󲦩󱌩󰵴󵒹󵉐󴋒󶑇󼵸󱱄
B
󼵹
󴎥󽴼󷸽󵟂󱁃󲹡󵒹󵉐󴋒󶑇
1
󲦻󲔥󱌍󱋏󵉐
󲘝󵉐󴋒󶑇󲔞󷠴󱑍󲦩󱌩󳅜󳪒󰶦
1.
󲘝󵉐󴋒󶑇
1
󲘇󹿆󲦩󱌩󳅜󳪒󱌼󵒹󸎫󸖥󼵸󱱄
B
󼵹
2.
󲘝󵉐󴋒󶑇󴚿󱌇󳅜󳪒󱌼󼵼󰾫󱌧󴶗󴶗󱲒󱱀󲕂󱲉󲦩󱌩󱌼󼵼󲪈󵟂󱁃󲹡󱞒
󱑍󱌧󸹊󲕂󱑍󰽚󵒹󱽯󹌊
󰺣󲦩󱌩󰶦󱜌󱐁󵉐󴋒󶑇
1.
󳉾󰵵󸡻󳙟󳉾󸷶
2󼵼󲘝 󵉐 󴋒 󶑇 󰺣 󲦩 󱌩 󳏤 󳪒 󰶦 󵫙 󲃇 󱲒 󳈙 󱐁
2.
󳉾󳦦󳅜󱍄󱋏󵉐󱬽󸛉󱐕󳄿󸒤󲘝󵉐󴋒󶑇󳏄󱌇󱋏󵉐󱬽󰶦
󵉐󴋒󶑇󵉐󸢁󷷧󼵸󱱄
B
󼵹
󰵨󰹉
DeWALT
󵉐󴋒󶑇󲨅󳥤󰵨󰶢󱖬󱞏󰵳󰶢󶒂󶮁
LED
󳉸󵤚󴦨󵒹󵉐󸢁
󷷧󼵼󵈾󰸶󳉸󵤚󵉐󴋒󶑇󱌼󵒹󱒦󰽯󵉐󸢁
󳉾󰵵󵉐󸢁󷷧󳉾󸷶
14
󰵷󳨡󲮔󼵼󱙱󱜴󱞘󱔔󵉐󸢁󷷧󰵳󰶢󶒂󶮁
LED
󳉸
󵤚󴦨󲘝󰻅󶑇󱝗󳜱󲮮󰹮󸁱󼵼󰻅󳉸󵤚󱒦󰽯󵉐󸢁󲰳󵉐󴋒󱌼󵒹󵉐󸢁󰽜󰸶󱜴
󵈾 󸿴 󱑗 󳞟 󼵼󵉐 󸢁 󷷧 󲘝 󰵷 󰼕 󰹮 󸁱 󼵼󵉐 󴋒 󲘝 󹄾 󷦴 󸡿 󳜞 󱋏 󵉐
󴎥󽴼󵉐󸢁󷷧󰺒󳉸󵤚󵉐󴋒󶑇󵒹󱒦󰽯󵉐󸢁󲔑󲪈󰵷󷞎󵤚󷸫󲦩󱌩󵒹󱔇󶡋󼵼
󰶃󲘝󳭐󳌙󰹢󱡸󶑇󰻞󴖜󲫟󱠥󳥓󶑋󵈾󳄫󵒹󰾫󵈾󲺕󱎄󶙝󳥤󳄿󰵷󱝛
󵓽 󲨅 󳅿󼵸 󱱄
C
󼵹
󱜴󸓦󸞂󰻞
󷵪󱟈󽴼󰶺 󸿮 󰽜 󰶛 󸡿 󵒹 󰺄 󸉨 󰼠 󲕳 󹑦 󹀘 󼵼󷸽 󱖢 󲘝󲦩󱌩󲹨󳉲󱲉󱿣
󹏞󰵴󳜱󳃵󵈾󵓽󲨅󳅿󲹨󳉲󴶠󱡸󱜬󶡋󰾫󵈾󲦩󰽳󵓽󲨅󲹨󳉲󲦩
󱌩󵒹󵓽󲨅󳅿
󷵪󱟈󽴼󰶺 󰸬 󸿮 󰽜 󰶛 󸡿 󰺄 󸉨 󰼠 󲕳 󵒹 󱙮 󹀘 󼵼󷸽󵟂󱁃󱱀󲕂󵓽󲨅󳅿
󲒪󵒹󷙡󰶐󳟾󴶗󱱀󵒹
󸡿󷦴󱁍󲸃󽴼󲔞󷠴󳃵󳥀󳌄󵓽󲨅󳅿󳞟󼵼󱜬󰾫󵈾󳏀󰿙󵒹󷙡󸷑󱔊󲳴󳉉󶄓
󷙡󰶐
󱜴󰾫󵈾󳏀󰿙󵒹󷙡󰶐
12
󲘝󵓽󲨅󳅿
11
󷠴 󱑍 󲦩 󱌩 󵒹 󰻤 󲼒 󰵨 󰿪 󼵼󰻅 󳜱
󱀒󰷵󲻘󲦪󳅜󳕽󰽳󳃵󰷵󲻘󱜹󳅜󳕽󰽳󵒹󵈾󳄫󰾫󵈾󳝾󹄾󵓽󲨅󳅿󳞟󼵼󱜴
󰻅󰺣󲦩󱌩󰵴󳈓󹀒
󶱰󷦴󳈓󹀒󵓽󲨅󳅿󼵼󷸽󱜌󰵵󱱀󲕂󲔑󰻍󵒹󷙡󸷑
12󼵼󴬭 󱝠 󱲉 󱜦 󰵨 󸐞 󸡿 󳜞
󷠴 󰵴 󱔊 󲳴 󳉉 󶄓 󷙡 󰶐
󲘝󸸃󱿣󳃵󸿢󰻞󲔞󷠴󱑍󳝾󸹊󱗑󱿫󱿣󰶦
󽵈󱱄
D
󽵉
󷵪󱟈󽴼󰵷󷦴󲙃󷸛󸔒󸑃󳏤󰽟󱿫󱿣󱑹󵱯󱠥󳅨󲮔󲦩󱌩󳧼󳉉󶄓󸸃
󱿣󼵸󳃵󰻤󰽧󱌧󲔑󸞂󰻞󼵹󸑰󱜴󶡋󰼕󲘌󶩞󱿫󱿣󱜍󳌁󱠥󰺄󸉨󰼠
󲕳󳥀󳌄󸞂󰻞󳞟󼵼󷸽󲄥󶑋󸹊󲕂󷩙󱜅󲮔󱌣󲪈󳜘󲮔󲦩󱌩󵒹󵉐
󴙃󸑷󳍺
󷵪󱟈󽴼󱞘󱔔󲦩󱌩󰷔󱑹󲪿󵟂󱁃󸸃󱿣󲔞󷠴󵫙󱱀󳨡󱔔󵒹󸸃󱿣󱜴
󶡋󰼕󰺣󲦩󱌩󶢵󶽆󼵼󰺣󶙝󱜴󶡋󲘌󶩞󰺄󸉨󰼠󲕳
󲹡󵒹󲦩󱌩󱾋󳥤󳝾󸹊󱗑󱿫󱿣
10󼵼󲨅 󳥤 󰵨 󰶢 󳝓 󸎯 󲀜 󵷘
9󼵼󱀒 󰸶 󱙁 󳅜 󳕽
󰽳󱿫󱿣󲁶󳩔󷦴󳏄󱌇󸸃󱿣󳃵󱌧󰺮󸞂󰻞󼵼󷸽󳆅󷝥󰵵󱐪󴄀󹞣
1.
󱌣󸽼󵉐󴙃󲪈󱜌󰵵󵉐󴋒󶑇
2.
󵈾󰵨󱜬󳅜󳇌󰽟󱿫󱿣󵒹󹺲󶮁󲀜󵷘󼵼󵈾󱜦󰵨󱜬󳅜󱱀󲕂󲦩󱌩󸓠󳞟󸷐
󳝓󸎯󲀜󵷘󰻅󳏄󱌇󳄿󹄾󵒹󸞂󰻞
3.
󲘝󸿢󰻞󳏄󱌇󱿫󱿣󶐩
19
󴈘󵾜󼵼󴬭󱝠󵈾󰵨󱜬󳅜󹏢󳞟󸷐󳝓󸎯󱿫󱿣󼵼
󱜦󰵨󱜬󳅜󱐮󳏤󰽟󲦩󱌩󼵼󲘝󸿢󰻞󸎯󶄓󲹡󵒹󲦩󱌩󸞂󱾋󰵨󰶢󶩉󱔔󰶻
󸎷󸹊󷠴󶔩󱏫󱂷󴃽󷠴󶔩󼵼󲹡󱜬󹄾󰵨󱜬󳅜󱙱󱜴󳅨󲮔󱠥󱌣󸽼󱿫󱿣
󷸽󵟂󱁃󱲉󳉉󶄓󱿫󱿣󳞟󵈾󰵨󱜬󳅜󳏤󰽟󱿫󱿣󲀜󵷘󼵼󵈾󱜦󰵨󱜬󳅜󳏤󰽟󲦩
󱌩 󼵼󰻅 󶸧 󲲥 󳥓 󱿑 󵒹 󶄓 󲖚 󲶎
󶱰󷦴󳨡󲮔󸿢󰻞󼵼󷸽󸡿󱾖󰵴󸒤󴄀󹞣
1
󱠥
2
󸎯 󸔠 󸓦 󳉋󼵸 󱱄
A
󼵹
󷸫󲦩󱌩󳥤󰶚󵨬󸔠󲫟󷸄󶔩󼵼󱜴󵈾󰸶󰵷󱝛󰽳󰶍󱲟󳡟
󴎥󽴼󲦩󱌩󸑙󷝥󳞟󱐘󱖢󳥀󳙗󸔠󲫟󱲉󳥀󳙗󸔠󲫟󰷔󱑹󼵼󱔊󲳴󵴞󲲊󲦩󱌩
󲔥󱌍󱄣󴃻
1.
󶱰󷦴󸓦󳉋󸔠󲫟
1
󼵸󹠟󳆎󵜄󷸄󶔩󼵹󼵼󷸽󱌣󸽼󲦩󱌩󲪈󷷯󲔑󱄣󴃻󸎯󱔔
󱝣󱝠󴚿󱔔󸎯󸔠󸓦󳉋󱬽
7
󽵈󸑵󵨍󱿫󱿣󽵉
2.
󶱰󷦴󸓦󳉋󸔠󲫟
2
󼵸󹠟󸔠󷸄󶔩󼵹󼵼󷸽󱌣󸽼󲦩󱌩󲪈󷷯󲔑󱄣󴃻󸎯󱔔
󱝣󱑹󴚿󱔔󸎯󸔠󸓦󳉋󱬽
7
󽵈󴚿󱝣󱿫󱿣󽵉
󲁶󳩔󲦩󱌩󴌶󳥤󳙗󱜎󸔠󲫟󼵼󷸽󵟂󷷪󸎯󸔠󸓦󳉋󲮔󱌣󲔥󱌍󱦄󱝗󱲉󱑹󸑴󳃵
󱝠󸓎󰽚󶔩
󳺸 󲮮 󸓦 󳉋󼵸 󱱄
A
󼵹
󳺸󲮮󸓦󳉋󴾡
6
󱜴󳭐󳌙󹏬󲕂󵈾󸔁󰻅󸓦󳉋󴃼󵟂󵒹󳕽󰽳󳺸󲮮
󲁶󹄾󸓦󳉋󼵼󷸽󳝓󸎯󸎷󴾡󼵼󵕭󱑍󳄿󹄾󵒹󳫼󷸌󰵹󵷫󱿣󲘇󹿆
󳫼󷸌 󳺸󲮮
󸸃󲒱
1–15
󷙡 󰶐 󲔞 󷠴󼵸 󳚩 󲒷 󸂋 󱿑
=
󳆎󵜄󸂋󱿑󼵹
󱜎󸔠󷩙󱜅󲮔󱌣󱛻󴃼󱜀󸎯󳍾󱑗󳉾󸷶
󽵈󱱄
A
󽵉
󵉐󸸃󸔒󸑃󳉾󰵵󱠥󳨡󲮔󱜎󸔠󷩙󱜅󲮔󱌣
4
󲮔 󱞘 󱠥 󱌣 󸽼 󷩙 󱜅 󲮔 󱌣 󳉾
󲲥󸂋󴕀󼵼󸸃󲒱󸔠󲫟󲙡󸂋󲴰󲹡󵒹󲦩󱌩󸞂󱾋󱑗󱔔󱬽󷩙󱜅󲮔󱌣󲔥󱌍󳨡
󲮔󳞟󱿫󱿣󲘝󱄣󴃻󸑙󰽳
󴃼
/
󱜀󸎯󳍾󱑗󳉾󸷶
5
󱜴󵟂󲕂󲦩󱌩󳝓󸎯󳜱󱝣󼵼󲪈󱜴󰽳󰶺󸹊󲕂󳉾󸷶
󰾫󵈾
󶱰󷦴󸓦󳉋󴃼󱝣󳝓󸎯󼵼󷸽󳨡󲮔󷩙󱜅󲮔󱌣󼵼󴬭󱝠󳉾󰵵󲦩󱌩󱜹󰿪󵒹
󴃼󱜀󸎯󳍾󱑗󳉾󸷶
󲁶󳩔󷦴󸓦󳉋󱜀󱝣󳝓󸎯󼵼󷸽󳉾󰵵󲦩󱌩󲦪󰿪󵒹󴃼󱜀󸎯󳍾󱑗󳉾󸷶
󴎥󽴼󳍾󱑗󳉾󸷶󵒹󰶦󲳲󰽚󶔩󰼕󲘝󲦩󱌩󸹊󲕂󱲉󱌣󸽼󴸑󲵗󳙗󱜎󳍾󱑗󳉾
󸷶󵒹󰽚󶔩󳞟󼵼󵟂󱁃󷩙󱜅󲮔󱌣󱾆󰸶󳨡󲮔󴸑󲵗
󴎥󽴼󰵷 󲮋 󷷴 󱲉 󱜎 󸔠 󶲵 󱰶 󱌼 󸑷 󶑰 󰾫 󵈾 󲦩 󱌩 󼵼󱞅 󱐮 󱜴 󶡋 󰼕 󳌁 󱳂 󲮔 󱌣 󼵼
󱰕󴃽󲪿󲙵󸢁󸘚󱋞
󴎥󽴼󳙗󱜎󳝓󸎯󳜱󱝣󱝠󵳧󰵨󴂄󸑙󷝥󲦩󱌩󳞟󼵼󲹡󱜴󶡋󰼕󱲉󱞘󱔔󳞟󱞒󱑍
󱠲󱢎󱽯
󸑰󳟾󴃼󲨣󴾢󷻍󼵼󲪈󰵷󷞎󵤚󱐁󴾢󸽽󹐀
9
󵶎󰽥󰶦󳛓
󳕽󰽳
󰾫󵈾󷸺󳟉
󷵪󱟈󽴼󷸽󲄥󶑋󸗾󲔜󲔞󱌍󲔜󱐮󰻅󱛻󸓔󵈾󷨟󱐮󵒹󷦴󴊡
󷵪󱟈󽴼󰶺󸿮󰽜󰶛󸡿󵒹󰺄󸉨󰼠󲕳󹑦󹀘󼵼󱲉󸑴󷝥󰻤󰽧󷹉󳚯󳃵
󱜌󱐁󲔞󷠴󸿢󰻞󳃵󸞂󰻞󰷔󱑹󼵼󷸽󱌣󸽼󲦩󱌩󲪈󳜘󲮔󵉐󴋒󶑇
󸑷󳍺󲼒󱾫󱞘󱔔󱜴󶡋󰼕󲘌󶩞󰺄󸉨󰼠󲕳
󴃼 󵟂 󵒹 󳅜 󳉰 󳜱 󲮮󼵸 󱱄
E
󼵹
󷵪󱟈󽴼󰶺 󸿮 󰽜 󰶛 󸡿 󵒹 󰺄 󸉨 󰼠 󲕳 󹑦 󹀘 󼵼󷸽 󱔊󲳴󰾫󵈾󴃼󵟂󵒹󳅜
󳉰󳜱󲮮󼵼󲁶󱱄󳄿󵤚
󷵪󱟈󽴼󰶺󸿮󰽜󰶛󸡿󰺄󸉨󰼠󲕳󵒹󹑦󹀘󼵼󷸽󱔊󲳴󶄓󳏤󲦩󱌩󰻅󸿉
󴃻󲼒󱾫󰸳󰻞
󴃼󵟂󵒹󳅜󳉰󳜱󲮮󷦴󴊡󰵨󱜬󳅜󳏤󰽟󳅜󳪒
3󼵼󱜦 󰵨 󱜬 󳅜 󱐮 󳏤 󰽟 󵉐 󴋒 󶑇
󲦩 󰽳 󴦨󼵸 󱱄
F
󼵹
󲦩󰽳󴦨
8
󰽚󰸶󲦩󱌩󵒹󲫁󲫡󰵴󲦩󰽳󴦨󲘝󱲉󳉾󱚔󷩙󱜅󲮔󱌣󳞟󱞘󱔔
󳨡󲮔󷩙󱜅󲮔󱌣󱝠󼵼󲦩󰽳󴦨󲘝󱲉󴮒󳟉󴸑󲵗󱁃󳉰
20
󵨳
󴎥󽴼󲦩󰽳󴦨󵈾󰸶󴮒󰹮󶄓󸚈󵒹󲦩󰽳󷞎󹈘󼵼󰵷󶡋󲰳󱄟󳅜󵉐󵴳󰾫󵈾
󳆅 󷝥 󲪿 󵈾󼵸 󱱄
A
󼵹
󷵪󱟈󽴼󰶺󸿮󰽜󰺄󸉨󰼠󲕳󹑦󹀘󼵼󷸽󱔊󲳴󵟂󱁃󴶗󱱀󸹣󲕂󳃵󱿫
󶄓󲦩󰻞
󷵪󱟈󽴼󱲉 󳙗 󱜎 󳝓 󸎯 󳜱 󱝣 󰷔 󱑹 󼵼󷸽 󱔊 󲳴 󵴞 󱑍 󵉐 󱔔 󳦽 󲔥 󱌍
󱄣󴃻
󰾫󵈾󱑹󵒹󱎦󱾋󲦩󰽳󽴼
󷸄󶔩󸎯󸔠󸓦󳉋󱬽
7󷸽 󱛭 󷨜
󸎯󸔠󸓦󳉋
󲘝󸓔󲰳󵒹󸸃󱿣󳃵󸿢󰻞󲔞󷠴󱑍󱿫󱿣󰶦󷸽󱛭󷨜
󲘝󸸃󱿣󳃵󸿢󰻞󲔞
󷠴󱑍󳝾󸹊󱗑󱿫󱿣󰶦
󷵪󱟈󽴼
󱐘󱖢󰾫󵈾󳦦󲦩󱌩󴕋󱝗󳃵󳐜󱔔󳟓󴱎󳃵󳟓󴳙󴓋󰽥󼵸󴋽󴍙
󸞋 󶀶 󵴞 󼵹
󱐘󱖢󴕋󱝗󳃵󳐜󳈝󱌩󳥤󳟓󴱎󳫼󵶋󵒹󴓋󰽥
󷙡󰶐󲔞󷠴
󲹡󵒹󲦩󱌩󱾋󳥤󱜴󷹉󶮝󳆎󵜄󵒹󵨍󱝗󱬽󼵼󰻅󵈾󰸶󳉉󷙡󰶐󱠥󱜌󱐁󱝑󵨬󵾬
󱴘 󱠥 󱿑 󲘮 󵒹 󶄓 󱱀 󰻞 󳺸 󲮮 󸓦 󳉋 󴾡
6
󰵴󵒹󳚩󲒷󵈾󰸶󷸄󲕂󷙡󰶐󲔞󷠴
󵒹󳆎󵜄󶲵󱰶󸎷󴾡󰵴󵒹󶒙󱝀󸂋󱿑󼵼󳆎󵜄󸂋󹠟󼵼󲪈󰶃󱜴󲔞󷠴󵒹󶄓󱱀
󰻞󰷳󸂋󱿑
1.
󲘝󳺸󲮮󸓦󳉋󴾡
6
󸎯 󶩜 󳄿 󹄾 󰽚 󶔩 󷸽 󱛭 󷨜
󳺸󲮮󸓦󳉋
2.
󳈙󱔔󷩙󱜅󲮔󱌣󼵼󰾫󱌧󰵹󸸃󱿣󳃮󵕭󶑂󼵼󵕭󱑍󶄓󱱀󰻞󰽚󰸶󲦩󰻞󳄿
󹄾󵒹󴕀󲫟
󷙡󰶐󲔞󷠴󲮋󷷴
󱔊󲳴󲄥󶑋󱋔󰺣󸏆󰽜󵒹󳆎󵜄󷸄󶔩󲮔󲄥󼵼󴬭󱝠󱍅󰾫󵈾󸏆󹠟󵒹󳆎󵜄
󷸄󶔩󰻅󸘚󱋞󳌁󱳂󲦩󰻞󳃵󶄓󱱀󰻞
󱲉󲦩󰻞󸏆󲘮󳃵󹁨󷆌󱘔󱶗󸑴󷝥󰵨󰹉󲕋󸿣󸑙󷝥󰻅󵟂󲕂󳺸󲮮󸓦󳉋󴾡
󵒹󴃼󵟂󰽚󶔩
󸸃󲒱
1.
󲘝󳺸󲮮󸓦󳉋󴾡
6
󸎯 󶩜 󵉐 󸸃 󵳘 󱝀 󷸽 󱛭 󷨜
󳺸󲮮󸓦󳉋
2.
󲘝󸸃󱿣󳙟󶔩󱲉󰵹󲦩󰻞󳍺󷩙󵒹󰽚󶔩
󴎥󽴼󷸽󰺒󰾫󵈾󸹔󱑅󵒹󸸃󱿣
3.
󳈙󱔔󷩙󱜅󲮔󱌣󰻅󰾫󱌧󰵹󸸃󱿣󳃮󵕭󶑂󼵼󵕭󱑍󱌧󰽚󰸶󲦩󰻞󳄿󹄾󵒹
󴕀󲫟
󷵪󱟈󽴼󲁶󳩔󸑃󸏀󼵼󵉐󸸃󱜴󶡋󰼕󱿠󸔠󼵼󰺣󶙝󲘌󶩞󵭳󴬭󳆎󸎯
󱔊󲳴󹏬󷷧󳟾󱞅󰼕󱜅󵈱󱿠󸔠󶄓󳏤󵉐󸸃󰻅󳍾󱑗󳆎󸎯󱔔󰽳󼵼
󸘚󱋞󰼠󲕳
4.
󰺣󳃮󲒱󰶦󳈙󱐁󸸃󱿣󳞟󼵼󷸽󱁃󳉰󹝪󸐫󸑙󸎯󼵼󰻅󸘚󱋞󱸨󱹲
󸸃󲒱󲮋󷷴
󸸃󲒱󳞟󼵼󷸽󲄥󶑋󰻅󸸃󱿣󴍡󵕭󶑂󳜷󱔉󱚔󱔃󼵼󰽏󰵷󷦴󱿑󱑍󵉐󳦽󱿠󸔠
󳃵󸸃󱿣󱃬󳛸
󲁶󳩔󸸃󱿣󱿠󸔠󽴼
-
󷸽󵰩󱙱󳨡󲮔󷩙󱜅󲮔󱌣󼵼󰺣 󲦩 󰻞 󰵴 󸓎 󱐁 󸸃 󱿣 󼵼󳫆 󳆫 󱿠 󸔠 󵒹
󱚳󱰕
-
󷸽󱖢󷸛󱱄󸔒󸑃󳉾󰵵󳨡󲮔󷩙󱜅󲮔󱌣󳧼󱞘󱔔󱿠󸔠󵒹󵉐󸸃
󸑰󰼕󳌁󱳂󵉐󸸃
-
󰶺󲙵󸢁󱎹󲘲󱿠󸔠󳙧󹁼󳃵󸘚󱋞󸸃󱿣󱲉󳧟󳛲󰶦󳇕󳜘󼵼󷸽󸿮󰽜󲘇
󵉐󸸃󵒹󱚔󱔃󼵼󰾫󸸃󱿣󰺣󲒱󵒹󳥓󱝠󸛉󱐕󰶦󶒖󱠥󰵵󳧼
󱲉 󸷪 󳧟 󰵴 󸸃 󱿑 󲒱󼵸
7
9
󴈘󵾜󶩜
12
7
󴈘󵾜󼵹󳞟󼵼󲁶󳩔󹗸󱋔󸸃󰵨󰶢
󱋔 󲘌 󲒱󼵸
4
󴈘󵾜󶩜
4
8
󴈘󵾜󼵹󼵼󰼕󴇲󸏆󲖃󳟓󸑴󷝥
󲁶󳩔󱲉󸏆󷈮󳃵󲖃󳟓󵝷󷠭󵒹󳧟󳛲󰵴󸸃󲒱󼵼󷸽󰾫󵈾󽶴󱵉󳨤󽶵󰻅󸿉󴃻
󳌁󱳂󲦩󰻞
󶑷󳇢
DeWALT
󵉐󱔔󲦩󱌩󷸄󷷧󶀶󶭼󼵼󱜴󰻅󸻌󳦎󰾫󵈾󼵼󶙝󰶃󱜬󹄾󳥓󲘲󵒹󶑷
󳇢󷦴󳉰󶑰󶸧󲲥󰻂󰺄󴛙󲼒󵒹󲦩󰽳󳙫󳩔󼵼󹄾󷦴󸑴󷝥󱝗󸓔󵒹󲦩󱌩󶑷󳇢
󱠥󲕂󳦎󴕢󴏈
󷵪󱟈󽴼󰶺 󰸬 󸿮 󰽜 󰶛 󸡿 󰺄 󸉨 󰼠 󲕳 󵒹 󹑦 󹀘 󼵼󷸽 󱲉 󷹉 󶮝 󳃵 󳈓 󱙹
󲔞󷠴󸿢󰻞󳃵󸞂󰻞󰷔󱑹󱌣󸽼󲦩󱌩󲪈󳜘󲮔󵉐󴋒󶑇󸑷󳍺󲼒󱾫
󱞘󱔔󱜴󶡋󰼕󲘌󶩞󰺄󸉨󰼠󲕳
󱋏󵉐󱬽󱠥󵉐󴋒󶑇󳝾󴎂󶑷󱁞
󴒺󴚿
󳦦󵉐󱔔󲦩󱌩󳝾󹄾󱜦󷝥󴒺󴚿
󴕢󴏈
󷵪󱟈󽴼󰵨󳞊󵖐󱑍󸔒󹑦󱜢󱛻󱌧󱟰󱰶󵩥󶛹󰸬󲘾󲚗󼵼󷸽󵈾󲪂󴲖󵒹
󵭠󴉟󲘝󴦫󲘾󱠥󲘾󲚗󰺣󰶻󳦽󱾫󱽳󱌼󱞫󱐁󳆅󷝥󴃽󸑃󵪑󳞟󼵼
󹄾󳄦󰵴󶑒󷷪󱜴󵒹󳇢󵕢󷠴󱾋󱠥󸿉󲘾󹈘󱌩
󷵪󱟈󽴼󷸽󱖢󰾫󵈾󴚉󱑬󳃵󱌧󲔑󱑟󴡩󲶎󱗋󲓗󱑗󱡸󳧼󴕢󴏈󲦩󱌩
󵒹󹈌󸢅󲚪󸛉󰻞󸑰󰹉󱗋󲓗󴶠󸀙󱜴󶡋󰼕󱑵󲯴󸑰󰹉󸛉󰽚󰾫󵈾
󵒹󳧟󳛲󷸽󵈾󲧓󷏔󴖜󱠥󵒹󶞎󵒶󴊑󳖮󳉏󱐘󱖢󷷯󰻤󰽧󴓋󰽥󴕸
󱌇󲦩󱌩󼵼󱐘󱖢󷷯󲦩󱌩󵒹󰻤󰽧󸛉󰻞󴑶󱲉󴓋󰽥󰶦
󱜴󸓦󸞂󰻞
󷵪󱟈󽴼󹀒󰸬
DeWALT
󳏀󰿙󵒹󸿢󰻞󰷔󱾫󼵼󱌧󰺮󸿢󰻞󸛫󳦣󶑒
󴃽 󰹢 󱡸 󱌰 󲖃 󲶎 󴐶 󷸛 󼵼󶱰 󲘝 󴃽 󵾬 󸿢 󰻞 󰵹 󳦦 󲦩 󱌩 󰵨 󸁱 󰾫 󵈾 󲘝
󲒹 󱲉 󲔞 󱌍 󹁨 󲹗 󰶺 󸿮 󰽜 󰺄 󸉨 󰼠 󲕳 󹑦 󹀘 󼵼󳦦 󰹢 󱡸 󱜬 󱜴 󰾫 󵈾
D
eWALT
󳎁󶵜󵒹󸿢󰻞
󷸽󱝣󲹡󵒹󶑒󸹉󱥂󱡑󷸨󳥀󱾵󱌣󰸶󱝗󸓔󸿢󰻞󵒹󱁍󲸃
17
简体中文
9
󵶎󰽥󰶦󳛓
󳕽󰽳
󰾫󵈾󷸺󳟉
󷵪󱟈󽴼󷸽󲄥󶑋󸗾󲔜󲔞󱌍󲔜󱐮󰻅󱛻󸓔󵈾󷨟󱐮󵒹󷦴󴊡
󷵪󱟈󽴼󰶺󸿮󰽜󰶛󸡿󵒹󰺄󸉨󰼠󲕳󹑦󹀘󼵼󱲉󸑴󷝥󰻤󰽧󷹉󳚯󳃵
󱜌󱐁󲔞󷠴󸿢󰻞󳃵󸞂󰻞󰷔󱑹󼵼󷸽󱌣󸽼󲦩󱌩󲪈󳜘󲮔󵉐󴋒󶑇
󸑷󳍺󲼒󱾫󱞘󱔔󱜴󶡋󰼕󲘌󶩞󰺄󸉨󰼠󲕳
󴃼 󵟂 󵒹 󳅜 󳉰 󳜱 󲮮󼵸 󱱄
E
󼵹
󷵪󱟈󽴼󰶺 󸿮 󰽜 󰶛 󸡿 󵒹 󰺄 󸉨 󰼠 󲕳 󹑦 󹀘 󼵼󷸽 󱔊󲳴󰾫󵈾󴃼󵟂󵒹󳅜
󳉰󳜱󲮮󼵼󲁶󱱄󳄿󵤚
󷵪󱟈󽴼󰶺󸿮󰽜󰶛󸡿󰺄󸉨󰼠󲕳󵒹󹑦󹀘󼵼󷸽󱔊󲳴󶄓󳏤󲦩󱌩󰻅󸿉
󴃻󲼒󱾫󰸳󰻞
󴃼󵟂󵒹󳅜󳉰󳜱󲮮󷦴󴊡󰵨󱜬󳅜󳏤󰽟󳅜󳪒
3󼵼󱜦 󰵨 󱜬 󳅜 󱐮 󳏤 󰽟 󵉐 󴋒 󶑇
󲦩 󰽳 󴦨󼵸 󱱄
F
󼵹
󲦩󰽳󴦨
8
󰽚󰸶󲦩󱌩󵒹󲫁󲫡󰵴󲦩󰽳󴦨󲘝󱲉󳉾󱚔󷩙󱜅󲮔󱌣󳞟󱞘󱔔
󳨡󲮔󷩙󱜅󲮔󱌣󱝠󼵼󲦩󰽳󴦨󲘝󱲉󴮒󳟉󴸑󲵗󱁃󳉰
20
󵨳
󴎥󽴼󲦩󰽳󴦨󵈾󰸶󴮒󰹮󶄓󸚈󵒹󲦩󰽳󷞎󹈘󼵼󰵷󶡋󲰳󱄟󳅜󵉐󵴳󰾫󵈾
󳆅 󷝥 󲪿 󵈾󼵸 󱱄
A
󼵹
󷵪󱟈󽴼󰶺󸿮󰽜󰺄󸉨󰼠󲕳󹑦󹀘󼵼󷸽󱔊󲳴󵟂󱁃󴶗󱱀󸹣󲕂󳃵󱿫
󶄓󲦩󰻞
󷵪󱟈󽴼󱲉 󳙗 󱜎 󳝓 󸎯 󳜱 󱝣 󰷔 󱑹 󼵼󷸽 󱔊 󲳴 󵴞 󱑍 󵉐 󱔔 󳦽 󲔥 󱌍
󱄣󴃻
󰾫󵈾󱑹󵒹󱎦󱾋󲦩󰽳󽴼
󷸄󶔩󸎯󸔠󸓦󳉋󱬽
7󷸽 󱛭 󷨜
󸎯󸔠󸓦󳉋
󲘝󸓔󲰳󵒹󸸃󱿣󳃵󸿢󰻞󲔞󷠴󱑍󱿫󱿣󰶦󷸽󱛭󷨜
󲘝󸸃󱿣󳃵󸿢󰻞󲔞
󷠴󱑍󳝾󸹊󱗑󱿫󱿣󰶦
󷵪󱟈󽴼
󱐘󱖢󰾫󵈾󳦦󲦩󱌩󴕋󱝗󳃵󳐜󱔔󳟓󴱎󳃵󳟓󴳙󴓋󰽥󼵸󴋽󴍙
󸞋 󶀶 󵴞 󼵹
󱐘󱖢󴕋󱝗󳃵󳐜󳈝󱌩󳥤󳟓󴱎󳫼󵶋󵒹󴓋󰽥
󷙡󰶐󲔞󷠴
󲹡󵒹󲦩󱌩󱾋󳥤󱜴󷹉󶮝󳆎󵜄󵒹󵨍󱝗󱬽󼵼󰻅󵈾󰸶󳉉󷙡󰶐󱠥󱜌󱐁󱝑󵨬󵾬
󱴘 󱠥 󱿑 󲘮 󵒹 󶄓 󱱀 󰻞 󳺸 󲮮 󸓦 󳉋 󴾡
6
󰵴󵒹󳚩󲒷󵈾󰸶󷸄󲕂󷙡󰶐󲔞󷠴
󵒹󳆎󵜄󶲵󱰶󸎷󴾡󰵴󵒹󶒙󱝀󸂋󱿑󼵼󳆎󵜄󸂋󹠟󼵼󲪈󰶃󱜴󲔞󷠴󵒹󶄓󱱀
󰻞󰷳󸂋󱿑
1.
󲘝󳺸󲮮󸓦󳉋󴾡
6
󸎯 󶩜 󳄿 󹄾 󰽚 󶔩 󷸽 󱛭 󷨜
󳺸󲮮󸓦󳉋
2.
󳈙󱔔󷩙󱜅󲮔󱌣󼵼󰾫󱌧󰵹󸸃󱿣󳃮󵕭󶑂󼵼󵕭󱑍󶄓󱱀󰻞󰽚󰸶󲦩󰻞󳄿
󹄾󵒹󴕀󲫟
󷙡󰶐󲔞󷠴󲮋󷷴
󱔊󲳴󲄥󶑋󱋔󰺣󸏆󰽜󵒹󳆎󵜄󷸄󶔩󲮔󲄥󼵼󴬭󱝠󱍅󰾫󵈾󸏆󹠟󵒹󳆎󵜄
󷸄󶔩󰻅󸘚󱋞󳌁󱳂󲦩󰻞󳃵󶄓󱱀󰻞
󱲉󲦩󰻞󸏆󲘮󳃵󹁨󷆌󱘔󱶗󸑴󷝥󰵨󰹉󲕋󸿣󸑙󷝥󰻅󵟂󲕂󳺸󲮮󸓦󳉋󴾡
󵒹󴃼󵟂󰽚󶔩
󸸃󲒱
1.
󲘝󳺸󲮮󸓦󳉋󴾡
6
󸎯 󶩜 󵉐 󸸃 󵳘 󱝀 󷸽 󱛭 󷨜
󳺸󲮮󸓦󳉋
2.
󲘝󸸃󱿣󳙟󶔩󱲉󰵹󲦩󰻞󳍺󷩙󵒹󰽚󶔩
󴎥󽴼󷸽󰺒󰾫󵈾󸹔󱑅󵒹󸸃󱿣
3.
󳈙󱔔󷩙󱜅󲮔󱌣󰻅󰾫󱌧󰵹󸸃󱿣󳃮󵕭󶑂󼵼󵕭󱑍󱌧󰽚󰸶󲦩󰻞󳄿󹄾󵒹
󴕀󲫟
󷵪󱟈󽴼󲁶󳩔󸑃󸏀󼵼󵉐󸸃󱜴󶡋󰼕󱿠󸔠󼵼󰺣󶙝󲘌󶩞󵭳󴬭󳆎󸎯
󱔊󲳴󹏬󷷧󳟾󱞅󰼕󱜅󵈱󱿠󸔠󶄓󳏤󵉐󸸃󰻅󳍾󱑗󳆎󸎯󱔔󰽳󼵼
󸘚󱋞󰼠󲕳
4.
󰺣󳃮󲒱󰶦󳈙󱐁󸸃󱿣󳞟󼵼󷸽󱁃󳉰󹝪󸐫󸑙󸎯󼵼󰻅󸘚󱋞󱸨󱹲
󸸃󲒱󲮋󷷴
󸸃󲒱󳞟󼵼󷸽󲄥󶑋󰻅󸸃󱿣󴍡󵕭󶑂󳜷󱔉󱚔󱔃󼵼󰽏󰵷󷦴󱿑󱑍󵉐󳦽󱿠󸔠
󳃵󸸃󱿣󱃬󳛸
󲁶󳩔󸸃󱿣󱿠󸔠󽴼
-
󷸽󵰩󱙱󳨡󲮔󷩙󱜅󲮔󱌣󼵼󰺣 󲦩 󰻞 󰵴 󸓎 󱐁 󸸃 󱿣 󼵼󳫆 󳆫 󱿠 󸔠 󵒹
󱚳󱰕
-
󷸽󱖢󷸛󱱄󸔒󸑃󳉾󰵵󳨡󲮔󷩙󱜅󲮔󱌣󳧼󱞘󱔔󱿠󸔠󵒹󵉐󸸃
󸑰󰼕󳌁󱳂󵉐󸸃
-
󰶺󲙵󸢁󱎹󲘲󱿠󸔠󳙧󹁼󳃵󸘚󱋞󸸃󱿣󱲉󳧟󳛲󰶦󳇕󳜘󼵼󷸽󸿮󰽜󲘇
󵉐󸸃󵒹󱚔󱔃󼵼󰾫󸸃󱿣󰺣󲒱󵒹󳥓󱝠󸛉󱐕󰶦󶒖󱠥󰵵󳧼
󱲉 󸷪 󳧟 󰵴 󸸃 󱿑 󲒱󼵸
7
9
󴈘󵾜󶩜
12
7
󴈘󵾜󼵹󳞟󼵼󲁶󳩔󹗸󱋔󸸃󰵨󰶢
󱋔 󲘌 󲒱󼵸
4
󴈘󵾜󶩜
4
8
󴈘󵾜󼵹󼵼󰼕󴇲󸏆󲖃󳟓󸑴󷝥
󲁶󳩔󱲉󸏆󷈮󳃵󲖃󳟓󵝷󷠭󵒹󳧟󳛲󰵴󸸃󲒱󼵼󷸽󰾫󵈾󽶴󱵉󳨤󽶵󰻅󸿉󴃻
󳌁󱳂󲦩󰻞
󶑷󳇢
DeWALT
󵉐󱔔󲦩󱌩󷸄󷷧󶀶󶭼󼵼󱜴󰻅󸻌󳦎󰾫󵈾󼵼󶙝󰶃󱜬󹄾󳥓󲘲󵒹󶑷
󳇢󷦴󳉰󶑰󶸧󲲥󰻂󰺄󴛙󲼒󵒹󲦩󰽳󳙫󳩔󼵼󹄾󷦴󸑴󷝥󱝗󸓔󵒹󲦩󱌩󶑷󳇢
󱠥󲕂󳦎󴕢󴏈
󷵪󱟈󽴼󰶺 󰸬 󸿮 󰽜 󰶛 󸡿 󰺄 󸉨 󰼠 󲕳 󵒹 󹑦 󹀘 󼵼󷸽 󱲉 󷹉 󶮝 󳃵 󳈓 󱙹
󲔞󷠴󸿢󰻞󳃵󸞂󰻞󰷔󱑹󱌣󸽼󲦩󱌩󲪈󳜘󲮔󵉐󴋒󶑇󸑷󳍺󲼒󱾫
󱞘󱔔󱜴󶡋󰼕󲘌󶩞󰺄󸉨󰼠󲕳
󱋏󵉐󱬽󱠥󵉐󴋒󶑇󳝾󴎂󶑷󱁞
󴒺󴚿
󳦦󵉐󱔔󲦩󱌩󳝾󹄾󱜦󷝥󴒺󴚿
󴕢󴏈
󷵪󱟈󽴼󰵨󳞊󵖐󱑍󸔒󹑦󱜢󱛻󱌧󱟰󱰶󵩥󶛹󰸬󲘾󲚗󼵼󷸽󵈾󲪂󴲖󵒹
󵭠󴉟󲘝󴦫󲘾󱠥󲘾󲚗󰺣󰶻󳦽󱾫󱽳󱌼󱞫󱐁󳆅󷝥󴃽󸑃󵪑󳞟󼵼
󹄾󳄦󰵴󶑒󷷪󱜴󵒹󳇢󵕢󷠴󱾋󱠥󸿉󲘾󹈘󱌩
󷵪󱟈󽴼󷸽󱖢󰾫󵈾󴚉󱑬󳃵󱌧󲔑󱑟󴡩󲶎󱗋󲓗󱑗󱡸󳧼󴕢󴏈󲦩󱌩
󵒹󹈌󸢅󲚪󸛉󰻞󸑰󰹉󱗋󲓗󴶠󸀙󱜴󶡋󰼕󱑵󲯴󸑰󰹉󸛉󰽚󰾫󵈾
󵒹󳧟󳛲󷸽󵈾󲧓󷏔󴖜󱠥󵒹󶞎󵒶󴊑󳖮󳉏󱐘󱖢󷷯󰻤󰽧󴓋󰽥󴕸
󱌇󲦩󱌩󼵼󱐘󱖢󷷯󲦩󱌩󵒹󰻤󰽧󸛉󰻞󴑶󱲉󴓋󰽥󰶦
󱜴󸓦󸞂󰻞
󷵪󱟈󽴼󹀒󰸬
DeWALT
󳏀󰿙󵒹󸿢󰻞󰷔󱾫󼵼󱌧󰺮󸿢󰻞󸛫󳦣󶑒
󴃽 󰹢 󱡸 󱌰 󲖃 󲶎 󴐶 󷸛 󼵼󶱰 󲘝 󴃽 󵾬 󸿢 󰻞 󰵹 󳦦 󲦩 󱌩 󰵨 󸁱 󰾫 󵈾 󲘝
󲒹 󱲉 󲔞 󱌍 󹁨 󲹗 󰶺 󸿮 󰽜 󰺄 󸉨 󰼠 󲕳 󹑦 󹀘 󼵼󳦦 󰹢 󱡸 󱜬 󱜴 󰾫 󵈾
DeWALT
󳎁󶵜󵒹󸿢󰻞
󷸽󱝣󲹡󵒹󶑒󸹉󱥂󱡑󷸨󳥀󱾵󱌣󰸶󱝗󸓔󸿢󰻞󵒹󱁍󲸃
18
简体中文
10
󵶎󰽥󰶦󳛓
󱁃󳇢󴾡󱺰
󱐕󵾬󱰑󳙑󵉌󴃽󵳘󱝀󳫼󷷶󵒹󰹢󱡸󱠥󵉐󴋒󰵷󲲥󰵹󳡝󸔒󲕼󲫮
󱴐󱲥󰵨󸁱󱾆󵀛
󰹢󱡸󱠥󵉐󴋒󱖬󱞏󱜴󲷫󱾖󳃵󱰑󳙑󵒹󳧟󳛲󼵼󰺣󶙝󸿮󰽜󲘇󱚳󳧟
󳛲󵒹󹄾󴊡󷸽󳭐󳌙󲰳󱲒󰿙󶑜󱰑󳙑󵉐󲒪󰹢󱡸󱠥󵉐󴋒󷦴󶸧
󲲥󳥀󱾵󱁍󲸃󼵼󷸽󱛭󵖐
www.2helpU.com
󱋏󵉐󲮮󵉐󴋒󶑇
󳦦󵉐󴋒󶑇󰾫󵈾󲘒󱠑󸻌󼵼󰵷󶡋󳏀󰿙󹏢󱑅󲔥󳃮󲦩󰽳󳄿󹄾󵒹󵉐󱔃󳞟󼵼
󲳴󹏣󸑴󷝥󱋏󵉐󵉐󴋒󳆯󳦪󲘒󱠑󶑖󳧳󳞟󼵼󷸽󲃇󱦥󱾆󵀛󰻅󱁃󳇢󴾡󱺰󽴼
󶙳󲙵󵉐󴋒󶑇󵒹󵉐󱔃󼵼󴬭󱝠󰺣󲦩󱌩󰵴󳈓󰵵
󸹋󵨍󲒪󵉐󴋒󳟾󱜴󱰑󳙑󵒹󷸽󲘝󲔑󰻍󸓑󲲄󲹡󵒹󶑒󸹉󱥂󱾆󳃵󲰳󱲒󵒹
󱰑󳙑󵱁󱰑󳙑󵒹󵉐󴋒󶑇󲘝󷠅󲃇󱦥󲳅󴾡󰾫󵈾󳃵󱾆󵀛
󰹢󱡸󰶦󳥤󲕳󴶠󸀙󵒹󱝝󵩧󱛻󱞏󸢁
󸛉󰻞󱝝󵩧
󳥤󲕳󴶠󸀙
󸸎󼵸
Pb
󼵹 󴋐󼵸
Hg
󼵹 󸺒󼵸
Cd
󼵹 󱌚 󰻠 󸸵󼵸
Cr
VI
󼵹 󱾵 󴚄 󶛬 󶲆󼵸
PBB
󼵹
󱾵󴚄󰸴󶲆󸠎
󽵈
PBDE
󽵉
󹝪󸐫󶑇󰻞
󳦽󱽳󶑇󰻞
󳍾󱑗󸛉󰻞
󽵈󲮔󱌣󼵼
PCB
󵴞󽵉
󰼜󱔔󸛉󰻞
󵉐󴋒󱖬
󱋏󵉐󱬽
󸿢 󰻞󼵸 󸸃 󱿣
/
󵜩󸎱󴵚󵴞󼵹
󵉐󶑂󶑇󰻞
󳦦󷞎󳭕󰿝󳌙
SJ/T 11364
󵒹󷨟󲕂󶒙󱑗
O
󽴼󳫼󷸌󷸫󳥤󲕳󴶠󸀙󱲉󷸫󸛉󰽚󳄿󳥤󱲳󸀙󳧟󳛲󰶦󵒹󱞏󸢁󱲳󱲉
GB/T 26572
󷨟󲕂󵒹󸿴󸢁󷦴󴊡󰻅󰵵
X
󽴼󳫼󷸌󷸫󳥤󲕳󴶠󸀙󶩜󲘲󱲉󷸫󸛉󰽚󵒹󳪥󰵨󱲳󸀙󳧟󳛲󰶦󵒹󱞏󸢁󸂅󱐁
GB/T 26572
󷨟󲕂󵒹󸿴󸢁󷦴󴊡
󱾋󴎥󽴼󳦦󰹢󱡸󰵷󲳴󱖬󱞏󰻅󰵴󳄿󸒤󵒹󳄿󳥤󸛉󰻞󵉌󰸶󵈱󰹢󲦩󶮍󱠥󳆯󳦪󵒹󰵷󱜴󳥐󰻀󲶎󼵼󳦦󰹢󱡸󰶦󱞏󳥤󳪥󰹉󳥤󲕳󴶠󸀙󼵼󱲉󴾡󱁃󰾫󵈾󳦎󸿴󱌼󱜴
󰻅󳙟󲳲󰾫󵈾󼵼󸂅󸑃󴾡󱁃󰾫󵈾󳦎󸿴󰷔󱝠󱐮󲪿󸑴󱌇󱰑󳙑󲳅󴾡󶂺󶑢
󴾡󱁃󰾫󵈾󳦎󸿴󰶺
󵉐󲒪󵉐󴉟󰹢󱡸󰶦󱞏󳥤󵒹󳥤󲕳󴶠󸀙󰵷󰼕󱜅󵈱󱾫󴍨󳃵󵭳󱜎󼵼󵉐󲒪󵉐󴉟󰹢󱡸󵈾󳄫󴃼󲨣󰾫󵈾󷸫󵉐󲒪󵉐󴉟󰹢󱡸󰵷󰼕󲘇󴾡󱺰󸔤󳃮󰶛
󸡿󴋔󳪪󳃵󲘇󱌧󰺄󸉨󸀓󰹢󸔤󳃮󰶛󸡿󳌁󲕳󵒹󳦎󸿴
󴾡󱁃󰾫󵈾󳦎󸿴󰶺
20
󲪄󴃽󴾡󱁃󰾫󵈾󳦎󸿴󰵷󰻀󷞎󰹢󱡸󵒹󲔞󱌍󰾫󵈾󳦎󸿴󱠥󸀙󸢁󱁃󷸇󲪄󸿴
󱑗󸔤󱥂󽴼󵒱󲲥󼵸󶰽󲦝󼵹󵨱󳆯󳥤󸿴󱌗󱝁
󱲒 󱲨 󽴼󶰽 󲦝 󲦩 󰶍 󱰪 󱘔 󶰽 󷑚 󰶦 󸄠
200
󱝀󱐁󱜢󱔉󲦩󱘔
󰹢 󱲒 󽴼󴋑 󶰽 󶰽 󲦝
N690140 06/2019
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

DeWalt DCD701M ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル

他の言語で