DCD791
DCD796
B
Copyright DeWALT
English (original instructions) 3
中文 (简体） 15
( 25
한국어 35
1
Figure 1
I
H
Figure 2
K
J
P
A
B
C
D
F
G
H
E
DCD796
M
N
O
L
2
Figure 3
Figure 7
C
C
F
Figure 4 Figure 5 Figure 6
Figure 8 Figure 9
Q
R
English
3
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make
DeWALT one of the most reliable partners for professional power tool users.
Technical Data
DCD791 DCD796
Voltage
V
DC
18 18
Battery type Li-Ion Li-Ion
Power output W 460 460
No-load speed
1st gear min
-1
0–550 0–550
2nd gear min
-1
0–2000 0–2000
Impact rate
1st gear min
-1
— 0–9,350
2nd gear min
-1
— 0–34,000
Max. torque (hard/soft) Nm 70/27 70/27
Chuck capacity mm 1.5–13.0 1.5–13.0
Maximum drilling capacity
Wood mm 40 40
Metal mm 13 13
Masonry mm — 13
Weight (without battery pack) kg 1.1 1.2
BRUSHLESS CORDLESS COMPACT 13 mm (1/2")
DRILL/DRIVER, DCD791
BRUSHLESS CORDLESS COMPACT 13 mm (1/2")
DRILL/DRIVER/HAMMERDRILL, DCD796
Battery pack DCB180 DCB181 DCB182 DCB183/B DCB184/B DCB185
Battery type Li-Ion Li-Ion Li-Ion Li-Ion Li-Ion Li-Ion
Voltage
V
DC
18 18 18 18 18 18
Capacity Ah 3.0 1.5 4.0 2.0 5.0 1.3
Weight kg 0.64 0.35 0.61 0.40/0.45 0.62/0.67 0.35
Charger DCB105
Mains voltage
V
AC
220-240
Battery type 10.8/14.4/18 Li-Ion
Approx. charging
time of
battery packs
min
25 (1.3 Ah)
55 (3.0 Ah)
30 (1.5 Ah)
70 (4.0 Ah)
40 (2.0 Ah)
90 (5.0 Ah)
Weight
kg 0.49
English (original instructions)
4
English
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Charger DCB107 DCB112
Mains voltage
V
AC
220-240 220-240
Battery type 10.8/14.4/18 Li-Ion 10.8/14.4/18 Li-Ion
Approx. charging time
of battery packs
min 60 (1.3 Ah) 70 (1.5 Ah) 90 (2.0 Ah) 40 (1.3 Ah) 45 (1.5 Ah) 60 (2.0 Ah)
140 (3.0 Ah) 185 (4.0 Ah) 240 (5.0 Ah) 90 (3.0 Ah) 120 (4.0 Ah) 150 (5.0 Ah)
Weight kg 0.29 0.36
Charger DCB113 DCB115
Mains voltage
V
AC
220-240 220-240
Battery type 10.8/14.4/18 Li-Ion 10.8/14.4/18 Li-Ion
Approx. charging time
of battery packs
min 30 (1.3 Ah) 35 (1.5 Ah) 50 (2.0 Ah) 25 (1.3 Ah) 30 (1.5 Ah) 40 (2.0 Ah)
70 (3.0 Ah) 100 (4.0 Ah) 120 (5.0 Ah) 55 (3.0 Ah) 70 (4.0 Ah) 90 (5.0 Ah)
Weight kg 0.4 0.5
Definitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not avoided,
may result in minor or moderate
injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of fire.
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result
in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to
your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
5
English
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with another
battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
6
English
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Visible radiation. Do not stare into light.
DATE CODE POSITION
The date code, which also includes the year of
manufacture, is printed into the housing.
Example:
2018 XX XX
Year of Manufacture
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual
contains important safety and operating
instructions for compatible battery chargers (refer to
TechnicalData).
• Before using charger, read all instructions and
cautionary markings on charger, battery pack,
and product using battery pack.
WARNING: Shock hazard. Do not allow
any liquid to get inside charger. Electric
shock may result.
WARNING: We recommend the use of
a residual current device with a residual
current rating of 30mA or less.
CAUTION: Burn hazard. To reduce
the risk of injury, charge only DeWALT
rechargeable batteries. Other types of
batteries may burst causing personal
injury and damage.
CAUTION: Children should be
supervised to ensure that they do not
play with the appliance.
NOTICE: Under certain conditions,
with the charger plugged into the power
supply, the exposed charging contacts
inside the charger can be shorted by
foreign material. Foreign materials of
a conductive nature such as, but not
limited to, steel wool, aluminum foil or
any buildup of metallic particles should
be kept away from charger cavities.
Always unplug the charger from the
power supply when there is no battery
pack in the cavity. Unplug charger before
attempting to clean
Additional Specific Safety Rules for
Drill/Driver/Hammerdrill
• Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
• Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
• Hold power tool by insulated gripping
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring. Cutting accessory contacting a
“live” wire may make exposed metal parts of the
power tool “live” and could give the operator an
electric shock.
• Hold power tool by insulated gripping
surfaces, when performing an operation
where the fastener may contact hidden
wiring. Fasteners contacting a "live" wire may
make exposed metal parts of the power tool
"live" and could give the operator an electric
shock.
• Use clamps or other practical way to secure
and support the workpiece to a stable
platform. Holding the work by hand or against
your body is unstable and may lead to loss of
control.
• Wear safety goggles or other eye protection.
Hammering and drilling operations cause chips
to fly. Flying particles can cause permanent eye
damage.
• Accessories and tool may get hot during
operation. Wear gloves when handling them if
performing heat producing applications such as
hammerdrilling and drilling metals.
• Do not operate this tool for long periods of
time. Vibration caused by hammer action may
be harmful to your hands and arms. Use gloves
to provide extra cushion and limit exposure by
taking frequent rest periods.
• Air vents often cover moving parts and
should be avoided. Loose clothes, jewelry or
long hair can be caught in moving parts.
Residual Risks
In spite of the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
– Impairment of hearing.
– Risk of squeezing fingers when changing
accessories.
– Health hazards caused by breathing dust
developed when working in wood.
– Risk of personal injury due to flying particles.
– Risk of personal injury due to prolonged use.
7
English
SAVE THESE INSTRUCTIONS
Chargers
The DCB105, DCB107, DCB112, DCB113, and
DCB115 chargers accept 10.8 V, 14.4V and 18V
Li-Ion XR (DCB140, DCB141, DCB142, DCB143,
DCB144, DCB145, DCB180, DCB181, DCB182,
DCB183, DCB183B, DCB184, DCB184B and
DCB185) battery packs.
DeWALT chargers require no adjustment and are
designed to be as easy as possible to operate.
Charging Procedure (Fig. 2)
1. Plug the charger into an appropriate outlet
before inserting battery pack.
2. Slide the battery pack (J) into the charger
ensuring that it is firmly seated and locked
in place. The red (charging) light will blink
continuously indicating that the charging
process has started.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
NOTE: To ensure maximum performance and life
of lithium-ion batteries, charge the battery pack fully
before first use.
Charging Process
Refer to the table below for the charge status of the
battery pack.
Charge indicators: DCB105
charging
fully charged
hot/cold pack delay
replace battery pack
Charge indicators: DCB107, DCB112, DCB113, DCB115
charging
fully charged
hot/cold pack delay*
*DCB107, DCB112, DCB113, DCB115: The
red light will continue to blink, but a yellow
indicator light will be illuminated during this
operation. Once the battery has reached an
appropriate temperature, the yellow light will turn
off and the charger will resume the charging
procedure.
• DO NOT attempt to charge the battery pack
with any chargers other than the ones in
this manual. The charger and battery pack are
specifically designed to work together.
• These chargers are not intended for
any uses other than charging DeWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock or
electrocution.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when
disconnecting charger. This will reduce risk
ofdamage to electric plug and cord.
• Make sure that cord is located so that it
will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
• Do not use an extension cord unless it
is absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock, or electrocution.
• Do not place any object on top of charger
or place the charger on a soft surface that
might block the ventilation slots and result
in excessive internal heat. Place the charger
in a position away from any heat source. The
charger is ventilated through slots in the top and
the bottom of the housing.
• Do not operate charger with damaged cord
or plug—have them replaced immediately.
• Do not operate charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way. Take it to an authorised
service centre.
• Do not disassemble charger; take it to an
authorised service centre when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution or
fire.
• In case of damaged power supply cord the
supply cord must be replaced immediately by
the manufacturer, its service agent or similar
qualified person to prevent any hazard.
• Disconnect the charger from the outlet
before attempting any cleaning. This will
reduce the risk of electric shock. Removing
the battery pack will not reduce this risk.
• NEVER attempt to connect two chargers
together.
• The charger is designed to operate on
standard 220-240V household electrical
power. Do not attempt to use it on any other
voltage. This does not apply to the vehicular
charger.
8
English
• Do not store or use the tool and battery
pack in locations where the temperature
may reach or exceed 40 ˚C (104 ˚F) (such as
outside sheds or metal buildings in summer).
WARNING: Never attempt to open the
battery pack for any reason. If battery
pack case is cracked or damaged,
do not insert into charger. Do not
crush, drop or damage battery pack.
Do not use a battery pack or charger
that has received a sharp blow, been
dropped, run over or damaged in any
way (i.e., pierced with a nail, hit with a
hammer, stepped on). Electric shock
or electrocution may result. Damaged
battery packs should be returned to
service centre for recycling.
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large
battery packs will stand upright on the
battery pack but may be easily knocked
over.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM-ION
(LI-ION)
• Do not incinerate the battery pack even if it
is severely damaged or is completely worn
out. The battery pack can explode in a fire.
Toxic fumes and materials are created when
lithium-ion battery packs are burned.
• If battery contents come into contact with
the skin, immediately wash area with mild
soap and water. If battery liquid gets into the
eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte
is composed of a mixture of liquid organic
carbonates and lithium salts.
• Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If
symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid
may be flammable if exposed to spark or
flame.
Transportation
DeWALT batteries comply with all applicable
shipping regulations as prescribed by industry
and legal standards which include UN
Recommendations on the Transport of Dangerous
Goods; International Air Transport Association
(IATA) Dangerous Goods Regulations, International
Maritime Dangerous Goods (IMDG) Regulations,
and the European Agreement Concerning The
The compatible charger(s) will not charge a faulty
battery pack. The charger will indicate faulty battery
by refusing to light or by displaying problem pack or
charger blink pattern.
NOTE: This could also mean a problem with a
charger.
If the charger indicates a problem, take the charger
and battery pack to be tested at an authorised
service centre.
HOT/COLD PACK DELAY
When the charger detects a battery that is too hot
or too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
A cold battery pack will charge at about half the
rate of a warm battery pack. The battery pack will
charge at that slower rate throughout the entire
charging cycle and will not return to maximum
charge rate even if the battery warms.
LITHIUM-ION BATTERY PACKS ONLY
XR Li-Ion tools are designed with an Electronic
Protection System that will protect the battery
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place
the lithium-ion battery on the charger until it is fully
charged.
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure
to include catalog number and voltage.
The battery pack is not fully charged out of the
carton. Before using the battery pack and charger,
read the safety instructions below. Then follow
charging procedures outlined.
READ ALL INSTRUCTIONS
• Do not charge or use battery in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting
or removing the battery from the charger may
ignite the dust or fumes.
• Never force battery pack into charger. Do
not modify battery pack in any way to fit into
a non-compatible charger as battery pack
may rupture causing serious personal injury.
• Charge the battery packs only in DeWALT
chargers.
• DO NOT splash or immerse in water or other
liquids.
9
English
NOTE: Battery packs should not be stored
completely depleted of charge. The battery pack will
need to be recharged before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual,
the labels on the charger and the battery pack may
show the following pictographs:
Read instruction manual before use.
See Technical Data for charging time.
Battery charging.
Battery charged.
Battery defective.
Hot/cold pack delay.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Do not expose to water.
Have defective cords replaced
immediately.
Charge only between 4 ˚C and 40 ˚C.
Only for indoor use.
Discard the battery pack with due care
for the environment.
Charge DeWALT battery packs only with
designated DeWALT chargers. Charging
battery packs other than the designated
DeWALT batteries with a DeWALT
charger may make them burst or lead
to other dangerous situations (see
Technical Data).
Do not incinerate the battery pack.
International Carriage of Dangerous Goods by Road
(ADR). Lithium-ion cells and batteries have been
tested to section 38.3 of the UN Recommendations
on the Transport of Dangerous Goods Manual of
Tests and Criteria.
In most instances, shipping a DeWALT battery pack
will be excepted from being classified as a fully
regulated Class 9 Hazardous Material. In general,
the two instances that require shipping Class 9 are:
1. Air shipping more than two DeWALT lithium-ion
battery packs when the package contains only
battery packs (no tools), and
2. Any shipment containing a lithium-ion battery
with an energy rating greater than 100 watt
hours (Wh). All lithium-ion batteries have the
watt hour rating marked on the pack.
Regardless of whether a shipment is considered
excepted or fully regulated, it is the shipper's
responsibility to consult the latest regulations for
packaging, labeling/marking and documentation
requirements.
Transporting batteries can possibly cause fire if the
battery terminals inadvertently come in contact with
conductive materials. When transporting batteries,
make sure that the battery terminals are protected
and well insulated from materials that could contact
them and cause a short circuit.
The information provided in this section of the
manual is provided in good faith and believed to be
accurate at the time the document was created.
However, no warranty, expressed or implied, is
given. It is the buyer’s responsibility to ensure that its
activities comply with the applicable regulations.
Battery Pack
BATTERY TYPE
The DCD791 and DCD796 operate on an 18 volt
battery pack.
The DCB180, DCB181, DCB182, DCB183,
DCB183B, DCB184, DCB184B or DCB185 battery
packs may be used. Refer to Technical Data for
more information.
Storage Recommendations
1. The best storage place is one that is cool and
dry away from direct sunlight and excess heat
or cold. For optimum battery performance and
life, store battery packs at room temperature
when not in use.
2. For long storage, it is recommended to store a
fully charged battery pack in a cool, dry place
out of the charger for optimal results.
10
English
DO NOT use under wet conditions or in the
presence of flammable liquids or gases.
These drills/drivers/hammerdrills are professional
power tools.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
• Young children and the infirm. This appliance
is not intended for use by young children or
infirm persons without supervision.
• This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the battery pack
voltage corresponds to the voltage on the rating
plate. Also make sure that the voltage of your
charger corresponds to that of your mains.
Your DeWALT charger is double insulated
in accordance with IEC60335; therefore
no earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DeWALT service organisation.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see Technical Data). The minimum conductor size
is 1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up can
cause injury.
WARNING: Use only DeWALT battery
packs and chargers.
Package Contents
The package contains:
1 Drill/driver or 1 drill/driver/hammerdrill
1 Charger
1 Li-Ion battery pack (C1, S1, D1, M1, P1 models)
2 Li-Ion battery packs (C2, S2, D2, M2, P2 models)
3 Li-Ion battery packs (C3, S3, D3, M3, P3 models)
1 Kitbox
1 Instruction manual
1 Tool Connect
TM
App instruction manual
(Bmodels)
1 Magnetic bit holder
1 Belt hook
NOTE: Battery packs, chargers and kitboxes
are not included with N models. Battery packs
and chargers are not included with NT models.
Bmodels include Bluetooth
®
battery packs.
NOTE: The Bluetooth
®
word mark and logos are
registered trademarks owned by the Bluetooth
®
,
SIG, Inc. and any use of such marks by DeWALT is
under license. Other trademarks and trade names
are those of their respective owners.
• Check for damage to the tool, parts or
accessories which may have occurred
during transport.
• Take the time to thoroughly read and
understand this manual prior to operation.
Description (Fig. 1)
WARNING: Never modify the power
tool or any part of it. Damage or personal
injury could result.
A. Trigger switch
B. Forward/reverse control button
C. Torque adjustment collar
D. Gear shifter
E. Worklight
F. Keyless chuck
G. Belt hook
H. Mounting screw
I. Bit clip
J. Battery pack
K. Battery release button
L. Worklight switch
INTENDED USE
These drills/drivers/hammerdrills are designed
for professional drilling, percussion drilling and
screwdriving applications.
11
English
The centre position of the control button locks
the tool in the off position. When changing the
position of the control button, be sure the trigger is
released.
NOTE: The first time the tool is run after changing
the direction of rotation, you may hear a click on
start up. This is normal and does not indicate a
problem.
Torque Adjustment Collar (Fig. 1)
Your tool has an adjustable torque screwdriver
mechanism for driving and removing a wide array
of fastener shapes and sizes and in some models,
a hammer mechanism for drilling into masonry.
Circling the collar (C) are numbers, a drill bit symbol,
and in some models, a hammer symbol. These
numbers are used to set the clutch to deliver a
torque range. The higher the number on the collar,
the higher the torque and the larger the fastener
which can be driven. To select any of the numbers,
rotate until the desired number aligns with the arrow.
NOTE: The torque adjustment collar is only
engaged during screwdriving mode and not in drill
and hammerdrill modes.
Dual Range Gearing (Fig. 1)
The dual range feature of your drill/driver allows you
to shift gears for greater versatility.
1. To select speed 1 (high torque setting), turn
the tool off and permit it to stop. Slide the gear
shifter (D) forward (towards the chuck).
2. To select speed 2 (low torque setting), turn the
tool off and permit it to stop. Slide the gear
shifter back (away from the chuck).
NOTE: Do not change gears when the tool
is running. Always allow the drill to come to a
complete stop before changing gears. If you are
having trouble changing gears, make sure that the
dual range gear shifter is either completely pushed
forward or completely pushed back.
LED Worklight (Fig. 1)
The LED worklight (E) and its worklight switch (L)
are located on the foot of the tool. The worklight is
activated when the trigger switch is depressed. The
low (M), medium (N) and spotlight (O) modes can
be changed by moving the switch on the foot of the
tool. If the trigger switch remains depressed, the
worklight will remain on in all modes.
When on low (M) and medium (N) settings, the
beam will automatically turn off 20 seconds after the
trigger switch is released.
Inserting and Removing the
Battery Pack from the Tool (Fig. 2)
NOTE: Make sure your battery pack (J) is fully
charged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the battery pack (J) with the rails inside
the tool’s handle (Fig. 2).
2. Slide it into the handle until the battery pack is
firmly seated in the tool and ensure that you
hear the lock snap into place.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the release buttons (K) and firmly pull the
battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
FUEL GAUGE BATTERY PACKS (FIG. 2)
Some DeWALT battery packs include a fuel gauge
which consists of three green LED lights that
indicate the level of charge remaining in the battery
pack.
To actuate the fuel gauge, press and hold the fuel
gauge button (P). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
Variable Speed Trigger Switch (Fig.1)
To turn the tool on, squeeze the trigger switch (A).
To turn the tool off, release the trigger switch. Your
tool is equipped with a brake. The chuck will stop
as soon as the trigger switch is fully released.
NOTE: Continuous use in variable speed range is
not recommended. It may damage the switch and
should be avoided.
Forward/Reverse Control Button
(Fig. 1)
A forward/reverse control button (B) determines the
direction of the tool and also serves as a lock-off
button.
To select forward rotation, release the trigger switch
and press the forward/reverse control button on
the right side of the tool.
To select reverse, press the forward/reverse control
button on the left side of the tool.
12
English
2. Grasp the black sleeve of the chuck with one
hand and use the other hand to secure the
tool. Rotate the sleeve counterclockwise far
enough to accept the desired accessory.
3. Insert the accessory about 19 mm (3/4") into
the chuck and tighten securely by rotating
the chuck sleeve clockwise with one hand
while holding the tool with the other. Your tool
is equipped with an automatic spindle lock
mechanism. This allows you to open and close
the chuck with one hand.
NOTE: Be sure to tighten chuck with one hand
on the chuck sleeve and one hand holding the
tool for maximum tightness.
To release the accessory, repeat steps 1 and 2
above.
Belt Hook and Bit Clip (Fig. 1)
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
WARNING: To reduce the risk of
serious personal injury, DO NOT
suspend tool overhead or suspend
objects from the belt hook. ONLY hang
tool’s belt hook from a work belt.
WARNING: To reduce the risk of
serious personal injury, ensure the
screw holding the belt hook is secure.
IMPORTANT: When attaching or replacing the
belt hook or bit clip, use only the screw (H) that is
provided. Be sure to securely tighten the screw.
The belt hook (G) and bit clip (I) can be be attached
to either side of the tool using only the screw (H)
provided, to accommodate left- or right- handed
users. If the hook or bit clip is not desired at all, it
can be removed from the tool.
To move belt hook or bit clip, remove the screw
(H) that holds it in place then reassemble on the
opposite side. Be sure to securely tighten the screw.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
SPOTLIGHT MODE
The high setting (O) is the spotlight mode. The
spotlight will run for 20 minutes after the trigger
switch is released. Two minutes before the spotlight
will shut off, it will flash twice and then dim. To
avoid the spotlight shutting off, lightly tap the trigger
switch.
WARNING: While using the worklight in
medium or spotlight mode, do not stare
at the light or place the drill in a position
which may cause anyone to stare into
the light. Serious eye injury could result.
CAUTION: When using the tool as
a spotlight, be sure it is secured on a
stable surface where it will not cause a
tripping or falling hazard.
CAUTION: Remove all accessories
from the chuck before using the drill as
a spotlight. Personal injury or property
damage could result.
LOW BATTERY WARNING
When in spotlight mode and the battery is nearing
complete discharge, the spotlight will flash twice
and then dim. After two minutes, the battery will be
completely discharged and the drill will immediately
shut down. At this point, replace with a charged
battery.
WARNING: To reduce the risk of
injury, always have a back-up battery
or secondary lighting available if the
situation warrants it.
Keyless Single Sleeve Chuck
(Fig. 7–9)
WARNING: Do not attempt to tighten
drill bits (or any other accessory) by
gripping the front part of the chuck and
turning the tool on. Damage to the chuck
and personal injury may result. Always
lock off trigger switch and disconnect
tool from power source when changing
acces sories.
WARNING: Always ensure the bit
is secure before starting the tool. A
loose bit may eject from tool causing
possible personal injury.
Your tool features a keyless chuck (F) with one
rotating sleeve for one-handed operation of the
chuck. To insert a drill bit or other accessory, follow
these steps.
1. Turn tool off and disconnect tool from power
source.
13
English
8. Keep the motor running when pulling the bit
back out of a drilled hole. This will help prevent
jamming.
9. With variable speed drills there is no need to
centre punch the point to be drilled. Use a
slow speed to start the hole and accelerate by
squeezing the trigger harder when the hole is
deep enough to drill without the bit skipping
out.
Hammerdrill Operation (DCD796 only)
(Fig. 1, 5)
1. Turn the collar (C) to the hammerdrill symbol.
2. Select the high speed (2) setting by sliding the
gear shifter (D) back (away from the chuck).
IMPORTANT: Use carbide-tipped or masonry
bits only.
3. Drill with just enough force on the hammer to
keep it from bouncing excessively or “rising” off
the bit. Too much force will cause slower drilling
speeds, overheating and lower drilling rate.
4. Drill straight, keeping the bit at a right angle to
the work. Do not exert side pressure on the bit
when drillling as this will cause clogging of the
bit flutes and a slower drilling speed.
5. When drilling deep holes, if the hammer speed
starts to drop off, pull the bit partially out of the
hole with tool stil running to help clear debris
from the hole.
NOTE: A smooth, even flow of dust from the hole
indicates proper drilling rate.
MAINTENANCE
Your DeWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular
cleaning.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up can
cause injury.
The charger and battery pack are not serviceable.
accessories. An accidental start-up can
cause injury.
Proper Hand Position (Fig. 3)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper
hand position as shown.
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the top
of the drill (Q) as shown, with the other hand on the
main handle (R).
Drill Operation (Fig. 1, 4)
WARNING: To reduce the risk of
personal injury, ALWAYS ensure
workpiece is anchored or clamped firmly.
If drilling thin material, use a wood “back-
up” block to prevent damage to the
material.
1. Turn the collar (Fig. 4, C) to the drill symbol.
2. Select the desired speed/torque range using
the gear shifter (Fig. 1, D) to match the speed
and torque to the planned operation.
3. For WOOD, use twist bits, spade bits, power
auger bits or hole saws. For METAL, use
high-speed steel twist drill bits or hole saws.
Use a cutting lubricant when drilling metals.
The exceptions are cast iron and brass which
should be drilled dry.
4. Always apply pressure in a straight line with the
bit. Use enough pressure to keep drill biting,
but do not push hard enough to stall the motor
or deflect the bit.
5. Hold tool firmly with both hands to control
the twisting action of the drill. If model is not
equipped with side handle, grip drill with one
hand on the handle and one hand on the
battery pack.
CAUTION: Drill may stall if overloaded
causing a sudden twist. Always expect
the stall. Grip the drill firmly to control the
twisting action and avoid injury.
6. IF DRILL STALLS, it is usually because
it is being overloaded or improperly used.
RELEASE TRIGGER IMMEDIATELY, remove
drill bit from work, and determine cause of
stalling. DO NOT CLICK TRIGGER ON AND
OFF IN AN ATTEMPT TO START A STALLED
DRILL — THIS CAN DAMAGE THE DRILL.
7. To minimise stalling or breaking through the
material, reduce pressure on drill and ease the
bit through the last fractional part of the hole.
14
English
Should you find one day that your DeWALT product
needs replacement, or if it is of no further use to
you, do not dispose of it with household waste.
Make this product available for separate collection.
Separate collection of used products
and packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
DeWALT provides a facility for the collection and
recycling of DeWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
DeWALT office at the address indicated in this
manual. Alternatively, a list of authorised DeWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when
it fails to produce sufficient power on jobs which
were easily done before. At the end of its technical
life, discard it with due care for our environment:
• Run the battery pack down completely, then
remove it from the tool.
• Lithium-ion cells are recyclable. Take them to
your dealer or a local recycling station. The
collected battery packs will be recycled or
disposed of properly.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
Optional Accessories
WARNING: Since accessories, other
than those offered by DeWALT, have not
been tested with this product, use of
such accessories with this tool could be
hazardous. To reduce the risk of injury,
only DeWALT recommended accessories
should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
15
简体中文
DCD791 18V锂电充电式无刷磁浮
13MM (1/2")电钻
DCD796 18V锂电充电式无刷磁浮
13MM (1/2")冲击钻
恭喜！
感谢您选购 DEWALT 工具。凭借多年的产品开发和创新经验，DEWALT 已经成为专业电动工具用户最可
靠的合作伙伴之一。
技术参数
DCD791 DCD796
电压 V
DC
18 18
电池类型 锂离子 锂离子
功率输出 W 460 460
空载转速
1 档 min
-1
0–550 0–550
2 档 min
-1
0–2000 0–2000
冲击率
1 档 min
-1
— 0–9,350
2 档 min
-1
— 0–34,000
最大扭矩（硬/软） Nm 70/27 70/27
夹头尺寸 mm 1.5–13.0 1.5–13.0
最大钻孔能力
木材 mm 40 40
金属 mm 13 13
砖石 mm — 13
重量（不含电池组） kg 1.1 1.2
电池组 DCB180 DCB181 DCB182 DCB183/B DCB184/B DCB185
电池类型 锂离子 锂离子 锂离子 锂离子 锂离子 锂离子
电压 V
DC
18 18 18 18 18 18
电池容量 Ah 3.0 1.5 4.0 2.0 5.0 1.3
重量 kg 0.64 0.35 0.61 0.40/0.45 0.62/0.67 0.35
充电器
DCB105
电源电压
V
AC
220
电池类型
10.8/14.4/18 锂离子
电池组的大约
充电时间
min
25 (1.3 Ah)
55 (3.0 Ah)
30 (1.5 Ah)
70 (4.0 Ah)
40 (2.0 Ah)
90 (5.0 Ah)
重量
kg 0.49
充电器
DCB107 DCB112
电源电压
V
AC
220 220
电池类型
10.8/14.4/18 锂离子 10.8/14.4/18 锂离子
电池组的大约充
电时间
min 60 (1.3 Ah) 70 (1.5 Ah) 90 (2.0 Ah) 40 (1.3 Ah) 45 (1.5 Ah) 60 (2.0 Ah)
140 (3.0 Ah) 185 (4.0 Ah) 240 (5.0 Ah) 90 (3.0 Ah) 120 (4.0 Ah) 150 (5.0 Ah)
重量
kg 0.29 0.36
16
简体中文
定义： 安全指南
下列定义描述了各标志术语的严重程度。请仔细阅
读本手册，并注意这些标志。
危险： 表示紧急危险情况，如果不加以
避免，将导致死亡或严重伤害。
警告： 表示存在潜在的危险情况，如
果不加以避免，可能导致死亡或严重伤
害。
警示： 表示存在潜在危险情况，如果不
加以避免，可能导致轻度或中度伤害。
注意： 表示存在不涉及人身伤害的情
况，如果不加以避免，可能导致财产损
失。
表示存在触电风险。
表示存在火灾风险。
警告： 为降低伤害风险，请阅读使用手
册。
电动工具通用安全警告
警告！阅读随电动工具提供的所有安
全警告、说明、图示和规定。不遵照以
下所列说明会导致电击、着火和／或
严重伤害。
保存所有警告和说明书以备查阅。
警告中的术语“电动工具”指市电驱动（有线）电
动工具或电池驱动（无线）电动工具。
a) 工作场地的安全
1)
保持工作场地清洁和明亮。杂乱和黑暗的场
地会引发事故。
2)
不要在易爆环境，如有易燃液体、气体或粉
尘的环境下操作电动工具。电动工具产生的
火花会点燃粉尘或气体。
3)
操作电动工具时，远离儿童和旁观者。注意
力不集中会使你失去对工具的控制。
b) 电气安全
1)
电动工具插头必须与插座相配。绝不能以任
何方式改装插头。需接地的电动工具不能使
用任何转换插头。未经改装的插头和相配的
插座将降低电击风险。
2)
避免人体接触接地表面，如管道、散热片和
冰箱。如果你身体接触接地表面会增加电
击风险。
充电器
DCB113 DCB115
电源电压
V
AC
220 220
电池类型
10.8/14.4/18 锂离子 10.8/14.4/18 锂离子
电池组的大约充
电时间
min 30 (1.3 Ah) 35 (1.5 Ah) 50 (2.0 Ah) 25 (1.3 Ah) 30 (1.5 Ah) 40 (2.0 Ah)
70 (3.0 Ah) 100 (4.0 Ah) 120 (5.0 Ah) 55 (3.0 Ah) 70 (4.0 Ah) 90 (5.0 Ah)
重量
kg 0.4 0.5
3)
不得将电动工具暴露在雨中或潮湿环境中。
水进入电动工具将增加电击风险。
4)
不得滥用软线。绝不能用软线搬运、拉动
电动工具或拔出其插头。使软线远离热源、
油、锐边或运动部件。受损或缠绕的软线会
增加电击风险。
5)
当在户外使用电动工具时，使用适合户外使
用的延长线。适合户外使用的电线将降低电
击风险。
6)
如果无法避免在潮湿环境中操作电动工具，
应使用带有剩余电流装置（RCD）保护的电
源。RCD的使用可降低电击风险。
c) 人身安全
1)
保持警觉，当操作电动工具时关注所从事
的操作并保持清醒。当你感到疲倦，或在有
药物、酒精或治疗反应时，不要操作电动工
具。在操作电动工具时瞬间的疏忽会导致严
重人身伤害。
2)
使用个人防护装置。始终佩戴护目镜。防护
装置，诸如适当条件下使用防尘面具、防滑
安全鞋、安全帽、听力防护等装置能减少人
身伤害。
3)
防止意外起动。在连接电源和/或电池包、拿
起或搬运工具前确保开关处于关断位置。手
指放在开关上搬运工具或开关处于接通时通
电会导致危险。
4)
在电动工具接通之前，拿掉所有调节钥匙或
扳手。遗留在电动工具旋转零件上的扳手或
钥匙会导致人身伤害。
5)
手不要过分伸展。时刻注意立足点和身体平
衡。这样能在意外情况下能更好地控制住电
动工具。
6)
着装适当。不要穿宽松衣服或佩戴饰品。让
你的头发和衣服远离运动部件。宽松衣服、
佩饰或长发可能会卷入运动部件。
7)
如果提供了与排屑、集尘设备连接用的装
置，要确保其连接完好且使用得当。使用集
尘装置可降低尘屑引起的危险。
8)
不要因为频繁使用工具而产生的熟悉感而掉
以轻心，忽视工具的安全准则。某个粗心的
动作可能在瞬间导致严重的伤害。
d) 电动工具使用和注意事项
1)
不要勉强使用电动工具，根据用途使用合适
的电动工具。选用合适的按照额定值设计的
电动工具会使你工作更有效、更安全。
17
简体中文
电钻/起子/冲击钻的附加安全细则
•
带耳罩进行冲击作业。暴露于噪声环境会导致
失聪。
•
使用辅助手柄。失控会导致人身伤害。
•
工具使用前应得到适当支撑。由于工具输出转
矩大，运行时没有适当支撑会失控导致人身伤
害。
•
当在钻削附件可能触及暗线的场合进行操作
时，通过绝缘握持面握持工具。钻削附件碰到
带电导线会使工具外露金属零件带电而使操作
者遭受电击。
•
在紧固件可能触及暗线进行操作时，要通过绝
缘握持面来握持工具。紧固件碰到带电导线会
使工具外露的金属零件带电从而使操作者受到
电击。
•
请佩戴安全护目镜或其他护目装备。冲击或钻
孔会导致碎片飞散。飞散的颗粒会对眼睛造成
永久性伤害。
•
钻头和工具会在使用过程中发热。接触时请佩
戴手套。
其他风险
尽管遵守了相关的安全法规并采用了安全装备，
某些其他风险仍然是无法避免的。这些风险包括：
– 听力损伤。
– 更换附件时扭伤手指的风险。
– 锯切木材时，吸入粉尘导致的健康危害。
– 飞溅颗粒造成的人身伤害风险。
– 长时间使用引起的人身伤害风险。
工具上的标记
工具上印有下列图形：
使用前请阅读使用手册。
可见辐射。切勿直视激光束。
日期码的位置
包含制造年份 的日期码印在工具外壳上。
示例：
2018 XX XX
制造年份
针对所有电池充电器的重要安全
说明
请妥善保管好这些说明： 本手册包含重要的兼容电
池充电器安全和操作说明（请参阅技术参数）。
2)
如果开关不能接通或关断电源，则不能使用
该电动工具。不能通过开关来控制的电动工
具是危险的且必须进行修理。
3)
在进行任何调节、更换附件或贮存电动工具
之前，必须从电源上拔掉插头和／或卸下电
池包（如可拆卸）。这种防护性的安全措施
降低了电动工具意外起动的风险。
4)
将闲置不用的电动工具贮存在儿童所及范围
之外，并且不允许不熟悉电动工具和不了解
这些说明的人操作电动工具。电动工具在未
经培训的使用者手中是危险的。
5)
维护电动工具及其附件。检查运动部件是否
调整到位或卡住，检查零件破损情况和影响
电动工具运行的其他状况。如有损坏，应在
使用前修理好电动工具。许多事故是由维护
不良的电动工具引发的。
6)
保持切削刀具锋利和清洁。维护良好地有锋
利切削刃的刀具不易卡住而且容易控制。
7)
按照使用说明书，并考虑作业条件和要进行
的作业来选择电动工具、附件和工具的刀头
等。将电动工具用于那些与其用途不符的操
作可能会导致危险情况。
8)
保持手柄和握持表面干燥、清洁，不得沾有
油脂。在意外的情况下，湿滑的手柄不能保
证握持的安全和对工具的控制。
e) 电池式工具使用和注意事项：
1)
仅使用生产者规定的充电器充电。将适用于
某种电池包的充电器用到其他电池包时可能
会发生着火危险。
2)
仅使用配有专用电池包的电动工具。 使用其
他电池包可能会产生伤害和着火危险。
3)
当电池包不用时，将它远离其他金属物体，
例如回形针、硬币、钥匙、钉子、螺钉或
其他小金属物体，以防电池包一端与另一
端连接。电池组端部短路可能会引起燃烧
或着火。
4)
在滥用条件下，液体可能会从电池组中溅
出，应避免接触。如果意外碰到液体，用水
冲洗。如果液体碰到了眼睛，还应寻求医疗
帮助。从电池中溅出的液体可能会发生腐蚀
或燃烧。
5)
不要使用损坏或改装过的电池包或工具。损
坏或改装过的电池组可能呈现无法预测的结
果，导致着火、爆炸或伤害。
6)
不要将电池包暴露于火或高温中。电池包
暴露于火或高于130°C的高温中可能导致
爆炸。
f) 维修
1)
让专业维修人员使用相同的备件维修电动工
具。这将保证所维修的电动工具的安全。
2)
决不能维修损坏的电池包。电池包仅能由生
产者或其授权的维修服务商进行维修。
18
简体中文
•
切勿将两个充电器连接在一起。
•
充电器设计用于采用 220V 家用电源操作。
请勿试图在任何其他电压下使用充电器。此规
则不适用于车载充电器。
请妥善保管好这些说明
充电器
DCB105、DCB107、DCB112、DCB113 和 DCB115
充电器可以向 10.8 V、14.4 V 和 18 V 锂离子
XR（DCB140、DCB141、DCB142、DCB143、
DCB144、DCB145、DCB180、DCB181、DCB182、
DCB183、DCB183B、DCB184、DCB184B 和
DCB185）
电池组充电。
DEWALT 充电器无需做出任何调整，专为简易操
作而设计。
充电程序（图 2）
1. 插入电池组前，先将充电器的插头插到相应的
电源插座上。
2. 将电池组 (J) 滑入充电器，确保电池组紧紧固
定并锁定到位。 红色（充电中）指示灯将不断
闪烁，表示充电过程已经开始。
3. 红色灯持续亮起表示充电完成。此时电池组已
完全充电，您可以使用电池组或将电池组留在
充电器上。
注： 为了确保锂离子电池的效能和使用寿命最大
化，在首次使用电池组之前必须将其完全充电。
充电程序
关于电池组的充电状态，请参阅下表。
充电状态指示灯： DCB105
充电中
已完全充电
热/冷电池组延迟
更换电池组
充电状态指示灯： DCB107、DCB112、
DCB113、DCB115
充电中
已完全充电
热/冷电池组延迟*
*DCB107、DCB112、DCB113、DCB115：
红色指示灯会继续闪烁，但黄色指示灯在本次
操作过程中会亮起。电池达到适当温度后，
黄色指示灯会熄灭，充电器将恢复充电程序。
此兼容充电器不能为故障的电池组充电。充电器指
示灯不亮或“故障的电池组或充电器”指示灯闪烁
时，表示电池有故障。
•
在使用充电器之前，请先阅读所有指示以及充
电器、电池组和使用电池组的产品上的警示标
记。
警告： 触电危险。请勿让任何液体渗
入充电器，否则可能会引起触电。
警告： 我们建议使用漏电保护额定电流
为 30 mA或以下的漏电保护装置。
警示： 灼伤危险。为降低人身伤害风
险，请仅使用 DEWALT 充电式电池充
电。使用其它类型的电池可能会引起爆
裂，并导致人身伤害和损害。
警示： 应看管好儿童，以确保他们不将
此设备当做玩具来玩。
注意： 在某些情况下，当充电器的插
头插入电源插座时，充电器内部裸露的
充电接触点可能因为外来物件而短路。
请勿让能导电的异物靠近充电器腔，
这些外来物件包括但不限于钢棉、铝箔
或任何金属颗粒的堆积物。充电器内没
有电池组时，请断开充电器与电源的连
接。清洗前，务必拔掉充电器。
•
请勿试图使用本手册指定的充电器以外的其他
任何充电器为电池组充电。充电器和电池组都
是专门设计的，互相配合使用。
•
除了为 DEWALT 充电式电池充电以外，这些
充电器并不能用于其它用途。 否则可能会导致
火灾、触电或电击。
•
请勿将充电器暴露于雨中或雪中。
•
断开充电器连接时，应拔下插头，切勿拉拽电
源线。这将降低对电插头和电线的损害风险。
•
确保电源线布置在不易踩踏、踢绊、拉扯或会
受到损害或压力的位置。
•
除非绝对必要，否则请勿使用延长线。使用不
正确的延长电线可能存在火灾、
触电或电击风险。
•
请勿将任何物件放在充电器上面，或是把充电
器放在可能会堵住通风槽的柔软表面，导致充
电器的内部过热。请把充电器放置在远离任何
热源的位置。充电器外壳顶端和底端具有通风
槽。
•
禁止使用电源线或插头已损坏的充电器。请立
即更换已损坏的充电器。
•
如果充电器受到强烈重击、掉落或出现其他损
坏情况，请勿使用充电器。请将损坏的充电器
送到授权维修中心维修。
•
请勿自行拆卸充电器。请将需要检修或修理的
充电器送到授权维修中心。重装不正确可能导
致触电、电击或火灾风险。
•
必须立即将已损坏的电源线交由制造商、服务
代理或类似的合格人员进行更换以防止安全隐
患。
• 清洁前，请先断开充电器和插座的连接，以降
低触电风险。取出电池组不会降低触电风险。
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
