DeWalt DCD995 ユーザーマニュアル

DCD932

DCD937

DCD990

DCD995

2

Copyright DeWALT

English (original instructions) 03

简体中文 15

繁體中文 27

한국어

39

1

Figure 1

e

c

d

b

a

f

i

Figure 2

i

h

l

i

h

k

j

m

DCD990

h

g

2

Figure 6 Figure 8

Figure 7

d

e

f

Figure 3

Figure 4 Figure 5

Figure 9

e

f

g

n

English

3

BRUSHLESS CORDLESS 13 mm (1/2")

DRILL/DRIVER, DCD932, DCD990

BRUSHLESS CORDLESS 13 mm (1/2")

DRILL/DRIVER/HAMMERDRILL, DCD937, DCD995

Congratulations!

You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make

DeWALT one of the most reliable partners for professional power tool users.

Technical Data

DCD932 DCD937 DCD990 DCD995

Voltage V

DC

14.4 14.4 18 18

Type 2 2 2 2

Battery Type Li-Ion Li-Ion Li-Ion Li-Ion

No-load speed

1st gear min

-1

0–420 0–420 0–450 0–450

2nd gear min

-1

0–1250 0–1250 0–1300 0–1300

3rd gear min

-1

0–1850 0–1850 0–2000 0–2000

Impact rate

1st gear min

-1

– 0–7140 – 0–7650

2nd gear min

-1

– 0–21250 – 0–22100

3rd gear min

-1

– 0–31450 – 0–34000

Max. torque (hard/soft) Nm 75/38 75/38 80/42 80/42

Chuck capacity mm 1.5–13 1.5–13 1.5–13 1.5–13

Maximum drilling capacity

Wood mm 45 45 50 50

Metal mm 13 13 13 13

Masonry mm – 14 – 16

Weight (without battery pack) kg 1.5 1.55 1.5 1.55

.

Battery pack DCB140 DCB141 DCB142 DCB143

Battery type Li-Ion Li-Ion Li-Ion Li-Ion

Voltage V

DC

14.4 14.4 14.4 14.4

Capacity A

h

3.0 1.5 4.0 2.0

Weight kg 0.53 0.30 0.54 0.30

Battery pack DCB180 DCB181 DCB182 DCB183

Battery type Li-Ion Li-Ion Li-Ion Li-Ion

Voltage V

DC

18 18 18 18

Capacity A

h

3.0 1.5 4.0 2.0

Weight kg 0.64 0.35 0.61 0.40

English

4

Charger DCB105

Mains voltage V

AC

220-240 V

Battery type Li-Ion

Approx. charging time min 30 40 55 70

(1.5 Ah (2.0 Ah (3.0 Ah (4.0 Ah

battery packs) battery packs) battery packs) battery packs)

Weight kg 0.49

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and

pay attention to these symbols.

DANGER: Indicates an imminently

hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING: Indicates a potentially

hazardous situation which, if not

avoided, could result in death or

serious injury.

CAUTION: Indicates a potentially

hazardous situation which, if not

avoided, may result in minor or

moderate injury.

NOTICE: Indicates a practice not

related to personal injury which, if

not avoided, may result in property

damage.

Denotes risk of electric shock.

Denotes risk of fire.

WARNING: To reduce the risk of injury,

read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings

and all instructions. Failure to follow

the warnings and instructions may result

in electric shock, fire and/or serious

injury.

Save all warningS and inStructionS

for future reference

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of

electric shock.

b) Avoid body contact with earthed or

grounded surfaces such as pipes,

radiators, ranges and refrigerators. There

is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the

risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a residual

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric

shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool while

you are tired or under the influence of

drugs, alcohol or medication. A moment of

inattention while operating power tools may

result in serious personal injury.

English

5

b) Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off position before

connecting to power source and/or

battery pack, picking up or carrying the

tool. Carrying power tools with your finger

on the switch or energising power tools that

have the switch on invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotating

part of the power tool may result in personal

injury.

e) Do not overreach. Keep proper

footing and balance at all times. This

enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce

dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job

better and safer at the rate for which it

was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the switch

is dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or the battery pack from

the power tool before making any

adjustments, changing accessories, or

storing power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and

tool bits etc., in accordance with these

instructions taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified

by the manufacturer. A charger that is

suitable for one type of battery pack may

create a risk of fire when used with another

battery pack.

b) Use power tools only with specifically

designated battery packs. Use of any

other battery packs may create a risk of

injury and fire.

c) When battery pack is not in use, keep it

away from other metal objects like paper

clips, coins, keys, nails, screws or other

small metal objects that can make a

connection from one terminal to another.

Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be

ejected from the battery, avoid contact.

If contact accidentally occurs, flush with

water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the

battery may cause irritation or burns.

6) SERVICE

a) Have your power tool serviced by a

qualified repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Additional Speciﬁc Safety Rules for

Drills/Drivers/Hammerdrills

 • Wearearprotectors. Exposure to noise can

cause hearing loss.

 • Useauxiliaryhandles,ifsuppliedwiththe

tool. Loss of control can cause personal injury.

 • Holdpowertoolbyinsulatedgripping

English

6

DATE CODE POSITION

The Date Code, which also includes the year of

manufacture, is printed into the housing surface that

forms the mounting joint between tool and battery.

Example:

2013 XX XX

Year of Manufacture

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual

contains important safety and operating instruc tions

for the DCB105 battery charger.

 • Beforeusingthecharger,readallinstructions

and cautionary markings on charger, battery

pack and product using the battery pack.

WARNING: Shock hazard. Do not allow

any liquid to get inside charger. Electric

shock may result.

CAUTION: Burn hazard. To reduce

the risk of injury, charge only

DeWALT

rechargeable battery packs. Other types

of batteries may overheat and burst

resulting in personal injury and property

damage.

CAUTION: Children should be

supervised to ensure that they do not

play with the appliance.

NOTICE: Under certain conditions, with

the charger plugged in to the power

supply, the exposed charging contacts

inside the charger can be shorted by

foreign material. Foreign materials of

a conductive nature such as, but not

limited to, steel wool, aluminum foil or

any buildup of metallic particles should

be kept away from charger cavities.

Always unplug the charger from the

power supply when there is no battery

pack in the cavity. Unplug charger

before attempting to clean.

 • DONOTattempttochargethebatterypack

with any chargers other than the ones in

this manual. The charger and battery pack are

specifically designed to work together.

 • Thesechargersarenotintendedfor

any uses other than charging

DeWALT

rechargeable batteries. Any other uses

may result in risk of fire, electric shock or

electrocution.

surfaces when performing an operation

where the cutting tool may contact hidden

wiring. Cutting accessory contacting a “live”

wire may make exposed metal parts of the

power tool “live” and could give the operator an

electric shock.

 • Useclampsorotherpracticalwaytosecure

and support the workpiece to a stable

platform. Holding the work by hand or against

your body is unstable and may lead to loss of

control.

 • Wearearprotectorswhenhammering

for extended periods of time. Prolonged

exposure to high intensity noise can cause

hearing loss. Temporary hearing loss or serious

ear drum damage may result from high sound

levels generated by hammerdrilling.

 • Wearsafetygogglesorothereyeprotection.

Hammering and drilling operations cause chips

to fly. Flying particles can cause permanent eye

damage.

 • Hammerbitsandtoolsgethotduring

operation. Wear gloves when touching them.

Residual Risks

The following risks are inherent to the use of

percussion drills:

– Injuries caused by touching the rotating parts or

hot parts of the tool.

In spite of the application of the relevant safety

regulations and the implementation of safety

devices, certain residual risks cannot be avoided.

These are:

– Impairment of hearing.

– Risk of squeezing fingers when changing

accessories.

– Health hazards caused by breathing dust

developed when working in wood.

– Risk of personal injury due to flying particles.

– Risk of personal injury due to prolonged use.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

English

7

 • Donotexposechargertorainorsnow.

 • Pullbyplugratherthancordwhen

disconnecting charger. This will reduce risk

of damage to electric plug and cord.

 • Makesurethatcordislocatedsothatitwill

not be stepped on, tripped over or otherwise

subjected to damage or stress.

 • Donotuseanextensioncordunlessit

is absolutely necessary. Use of improper

extension cord could result in risk of fire,

electric shock or electrocution.

 • Whenoperatingachargeroutdoors,always

provide a dry location and use an extension

cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of

electric shock.

 • Donotblocktheventilationslotsonthe

charger.Theventilationslotsarelocated

on the top and sides of the charger. Place

the charger in a position away from any heat

source.

 • Donotoperatechargerwithdamagedcord

or plug — have them replaced immediately.

 • Do not operate charger if it has received

a sharp blow, been dropped or otherwise

damaged in any way. Take it to an authorised

service centre.

 • Donotdisassemblethecharger;takeitto

an authorised service centre when service or

repair is required. Incorrect reassembly may

result in a risk of electric shock, electrocution or

fire.

 • Incaseofdamagedpowersupplycordthe

supply cord must be replaced immediately by

the manufacturer, its service agent or similar

qualified person to prevent any hazard.

 • Disconnectthechargerfromtheoutlet

beforeattemptinganycleaning.Thiswill

reduce the risk of electric shock. Removing

the battery pack will not reduce this risk.

• NEVERattempt to connect 2 chargers together.

 • Thechargerisdesignedtooperateon

standard220-240Vhouseholdelectrical

power. Do not attempt to use it on any other

voltage. This does not apply to the vehicular

charger.

Save tHeSe inStructionS

Chargers

The DCB105 charger accepts 10.8 V, 14.4 V and

18 V Li-Ion (DCB121, DCB123, DCB140, DCB141,

DCB142, DCB143, DCB180, DCB181, DCB182

and DCB183) battery packs.

This charger requires no adjustment and is designed

to be as easy as possible to operate.

Charging Procedure (ﬁg. 2)

1. Plug the charger into an appropriate 220-240 V

outlet before inserting the battery pack.

2. Insert the battery pack (h) into the charger,

making sure the pack is fully seated in the

charger. The red (charging) light will blink

continuously indicating that the charging

process has started.

3. The completion of charge will be indicated by

the red light remaining ON continuously. The

pack is fully charged and may be used at this

time or left in the charger.

NOTE: To ensure maximum performance and life of

Li-Ion batteries, charge the battery pack fully before

first use.

Charging Process

Refer to the table below for the state of charge of

the battery pack.

State of charge

charging –– –– –– ––

fully charged –––––––––––––––––

 hot/coldpackdelay ––•––•––• ––•

x

 problempackorcharger ••••••••••••

 problempowerline ••••••••••••

This charger will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing to

light or by displaying problem pack or charger blink

pattern.

NOTE: This could also mean a problem with a

charger.

If the charger indicates a problem, take the charger

and battery pack to be tested at an authorised

service centre.

Hot/Cold Pack Delay

When the charger detects a battery that is too hot

or too cold, it automatically starts a hot/cold pack

delay, suspending charging until the battery has

reached an appropriate temperature. The charger

then automatically switches to the pack charging

mode. This feature ensures maximum battery life.

English

8

result. Damaged battery packs should

be returned to the service centre for

recycling.

CAUTION: When not in use, place

tool on its side on a stable surface

where it will not cause a tripping or

falling hazard. Some tools with large

battery packs will stand upright on the

battery pack but may be easily knocked

over.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION

(Li-Ion)

 • Donotincineratethebatterypackevenifit

is severely damaged or is completely worn

out. The battery pack can explode in a fire.

Toxic fumes and materials are created when

lithium ion battery packs are burned.

 • Ifbatterycontentscomeintocontactwith

the skin, immediately wash the area with

mild soap and water. If the battery liquid gets

into the eye, rinse water over the open eye for

15 minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte

is composed of a mixture of liquid organic

carbonates and lithium salts.

 • Contentsofopenedbatterycellsmaycause

respiratory irritation. Provide fresh air. If

symptoms persists, seek medical attention.

WARNING: Burn hazard. Battery liquid

may be flammable if exposed to spark

or flame.

Battery Pack

BATTERY TYPE

The DCD932 and DCD937 operate on 14.4 volt

battery packs.

The DCD990 and DCD995 operate on 18 volt

battery pack.

The DCB140, DCB141, DCB142, DCB143,

DCB180, DCB181, DCB182 or DCB183 battery

packs may be used. Refer to Technical Data for

more information.

Storage Recommendations

1. The best storage place is one that is cool and

dry away from direct sunlight and excess heat

or cold. For optimum battery performance and

life, store battery packs at room temperature

when not in use.

2. For long storage, it is recommended to store a

fully charged battery pack in a cool, dry place

out of the charger for optimal results.

XR Li-Ion tools are designed with an Electronic

Protection System that will protect the battery

against overloading, overheating or deep discharge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the

Li-Ion battery on the charger until it is fully charged.

A cold battery pack will charge at about half the rate

of a warm battery pack. The battery pack will charge

at that slower rate throughout the entire charging

cycle and will not return to maximum charge rate

even if the battery warms.

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure

to include the catalog number and voltage.

The battery pack is not fully charged out of the

carton. Before using the battery pack and charger,

read the safety instructions below and then follow

the charging procedures outlined.

read all inStructionS

 • Donotchargeorusethebatterypack

in explosive atmospheres, such as in the

presence of flammable liquids, gases or

dust. Inserting or removing the battery pack

from the charger may ignite the dust or fumes.

• Never force the battery pack into charger.

Do not modify the battery pack in any way

to fit into a non-compatible charger as

battery pack may rupture causing serious

personal injury.

 • Chargethebatterypacksonlyindesignated

DeWALT chargers.

• DONOTsplash or immerse in water or other

liquids.

 • Donotstoreorusethetoolandbattery

pack in locations where the temperature

may reach or exceed 40°C (105°F) (such as

outside sheds or metal buildings in summer).

 • Forbestresults,makesurethebatterypackis

fully charged before use.

WARNING: Never attempt to open

the battery pack for any reason. If

the battery pack case is cracked or

damaged, do not insert it into the

charger. Do not crush, drop or damage

battery pack. Do not use a battery

pack or charger that has received a

sharp blow, been dropped, run over

or damaged in any way (e.g., pierced

with a nail, hit with a hammer, stepped

on). Electric shock or electrocution may

English

9

NOTE: Battery packs should not be stored

completely depleted of charge. The battery pack will

need to be recharged before use.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual,

the labels on the charger and the battery pack show

the following pictographs:

Read instruction manual before use.

Charging.

Fully charged.

Hot/cold pack delay.

x

Problem pack or charger.

Problem powerline.

Do not probe with conductive objects.

Do not charge damaged battery packs.

Use only with DeWALT battery packs.

Others may burst, causing personal injury

and damage.

Do not expose to water.

Have defective cords replaced

immediately.

Charge only between 4°C and 40°C.

Discard the battery pack with due care for

the environment.

Do not incinerate the battery pack.

Charges Li-Ion battery packs.

See Technical Data for charging time.

Only for indoor use.

Package Contents

The package contains:

1 Brushless cordless drill/driver

(DCD932, DCD990)

1 Brushless cordless hammerdrill

(DCD937, DCD995)

2 14.4 V Li-Ion battery packs (DCD932, DCD937)

2 18 V Li-Ion battery packs (DCD990, DCD995)

1 Kitbox

1 Charger

1 Side handle

1 Instruction manual

NOTE: Battery packs, chargers and kitboxes are not

included with N-models.

 • Checkfordamagetothetool,partsor

accessories which may have occurred during

transport.

 • Takethetimetothoroughlyreadand

understand this manual prior to operation.

Description (ﬁg. 1, 2)

WARNING: Never modify the power

tool or any part of it. Damage or

personal injury could result.

a. Trigger switch

b. Forward/reverse control button

c. Worklight

d. Chuck

e. Torque adjustment collar

f. Gear shifter

g. Side handle

h. Battery pack

i. Battery release button

j. Belt hook

k. Mounting screw

l. Magnetic bit holder

INTENDED USE

These drills drivers/hammerdrills are designed

for professional drilling, percussion drilling and

screwdriving applications.

DO NOT use under wet conditions or in presence of

flammable liquids or gases.

English

10

2. Slide it into the handle until the battery pack is

firmly seated in the tool and ensure that it does

not disengage.

TO REMOVE THE BATTERY PACK FROM THE TOOL

1. Press the battery release button (i) and firmly

pull the battery pack out of the tool handle.

2. Insert battery pack into the charger as

described in the charger section of this manual.

FUEL GAUGE BATTERY PACKS (FIG. 2)

Some D

eWALT battery packs include a fuel gauge

which consists of three green LED lights that

indicate the level of charge remaining in the battery

pack.

To actuate the fuel gauge, press and hold the fuel

gauge button (m). A combination of the three green

LED lights will illuminate designating the level of

charge left. When the level of charge in the battery

is below the usable limit, the fuel gauge will not

illuminate and the battery will need to be recharged.

NOTE: The fuel gauge is only an indication of the

charge left on the battery pack. It does not indicate

tool functionality and is subject to variation based

on product components, temperature and end-user

application.

Variable Speed Switch (ﬁg. 1)

To turn the tool on, squeeze the trigger switch (a).

To turn the tool off, release the trigger switch. Your

tool is equipped with a brake. The chuck will stop as

soon as the trigger switch is fully released.

NOTE: Continuous use in variable speed range is

not recommended. It may damage the switch and

should be avoided.

Side Handle (ﬁg. 1)

WARNING: To reduce the risk of

personal injury, ALWAYS operate

the tool with the side handle properly

installed. Failure to do so may result

in the side handle slipping during tool

operation and subsequent loss of

control. Hold tool with both hands to

maximize control.

The side handle (g) clamps to the front of the gear

case and may be rotated 360˚ to permit right- or

left-hand use. Side handle must be tightened

sufficiently to resist the twisting action of the tool if

the accessory binds or stalls. Be sure to grip the

side handle at the far end to control the tool

during a stall.

These drills/drivers/hammerdrills are professional

power tools.

DO NOT let children come into contact with the

tool. Supervision is required when inexperienced

operators use this tool.

 • Thisproductisnotintendedforusebypersons

(including children) suffering from diminished

physical, sensory or mental abilities; lack of

experience, knowledge or skills unless they are

supervised by a person responsible for their

safety. Children should never be left alone with

this product.

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the battery pack

voltage corresponds to the voltage on the rating

plate. Also make sure that the voltage of your

charger corresponds to that of your mains.

Your DeWALT charger is double insulated

in accordance with EN 60335; therefore

no earth wire is required.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

D

eWALT service organization.

Using an Extension Cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see Technical Data). The minimum conductor size

is 1 mm

2

; the maximum length is 30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: Prior to assembly and

adjustment, always remove the battery

pack. Always switch off the tool before

inserting or removing the battery pack.

WARNING: Use only DeWALT battery

packs and chargers.

Inserting and Removing the

Battery Pack from the Tool (ﬁg. 2)

NOTE: For best results, make sure your battery

pack is fully charged.

TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE

1. Align the battery pack (h) with the rails inside the

tool’s handle (fig. 2).

English

11

If model is not equipped with side handle, grip drill

with one hand on the handle and one hand on the

battery pack.

NOTE: Side handle comes equipped on all models.

Forward/Reverse Control Button

(ﬁg. 1)

A forward/reverse control button (b) determines the

direction of the tool and also serves as a lock off

button.

To select forward rotation, release the trigger switch

and depress the for ward/re verse control button on

the right side of the tool.

To select reverse, release the trigger switch and

depress the forward/reverse control button on the

left side of the tool.

The center position of the control button locks the

tool in the off position. When changing the position

of the control button, be sure the trigger is released.

NOTE: The first time the tool is run after changing

the direction of rotation, you may hear a click on

start up. This is normal and does not indicate a

problem.

Worklight (ﬁg. 1)

There is a worklight (c) located on the foot of the

tool. The worklight is activated when the trigger

switch is depressed. When the trigger switch is

released, the worklight will stay illuminated for up to

20 seconds.

NOTE: The worklight is for lighting the immediate

work surface and is not intended to be used as a

flashlight.

Torque Adjustment Collar/Electronic

Clutch (ﬁg. 3–5)

Your tool has an electronic adjustable torque

screwdriver mechanism for driving and removing

a wide array of fasteners. Circling the torque

adjustment collar (e) are numbers. These numbers

are used to set the clutch to deliver a torque range.

The higher the number on the collar, the higher the

torque and the larger the fastener which can be

driven. To select any of the numbers, rotate until the

desired number aligns with the arrow.

Three-Speed Gearing (ﬁg. 1, 3–5)

The three-speed feature of your tool allows you to

shift gears for greater versatility. To select speed 1

(highest torque setting), turn the tool off and permit it

to stop. Slide the gear shifter (f) all the way forward.

Speed 2 (middle torque and speed setting) is in the

middle position. Speed 3 (highest speed setting) is

to the rear.

NOTE: Do not change gears when the tool is

running. Always allow the drill to come to a complete

stop before changing gears. If you have trouble

changing gears, make sure that the gear shifter is

engaged in one of the three speed settings.

If the speed shifter becomes stuck or is difficult to

select the desired gear, pull the trigger switch (a) to

rotate the motor. Then select the gear.

Keyless Single Sleeve Chuck

(ﬁg. 6–8)

WARNING: Do not attempt to tighten

drill bits (or any other accessory) by

gripping the front part of the chuck

and turning the tool on. Damage to

the chuck and personal injury may

result. Always lock off trigger switch

and disconnect tool from power source

when changing acces sories.

WARNING: Always ensure the bit is

secure before starting the tool. A loose

bit may eject from tool causing possible

personal injury.

Your tool features a keyless chuck with one rotating

sleeve for one-handed operation of the chuck. To

insert a drill bit or other accessory, follow these

steps.

1. Turn off tool and disconnect tool from power

source.

2. Grasp the black sleeve of the chuck (d) with

one hand and use the other hand to secure the

tool as shown in Figure 6. Rotate the sleeve

counterclockwise (as viewed from the front) far

enough to accept the desired accessory.

3. Insert the accessory about 19 mm (3/4") into

the chuck (fig. 7). Tighten securely by rotating

the chuck sleeve clockwise with one hand while

holding the tool with the other hand (fig. 8).

Continue to rotate the chuck sleeve until several

ratchet clicks are heard to ensure full gripping

power.

To release the accessory, repeat Steps 1 and 2

above.

Be sure to tighten chuck with one hand on the

chuck sleeve and one hand holding the tool for

maximum tightness.

English

12

Proper hand position requires one hand on the main

handle (n), with the other hand on the side handle

(g).

Drill Operation (ﬁg. 4)

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

WARNING: To reduce the risk of

personal injury, ALWAYS ensure

workpiece is anchored or clamped

firmly. If drilling thin material, use a wood

“back-up” block to prevent damage to

the material.

1. Select the desired speed/torque range using

the gear shifter to match the speed and torque

to the planned operation. Set the torque

adjustment collar (e) to the drill symbol.

2. For WOOD, use twist bits, spade bits, power

auger bits or hole saws. For METAL, use high-

speed steel twist drill bits or hole saws. Use

a cutting lubricant when drilling metals. The

exceptions are cast iron and brass which should

be drilled dry.

3. Always apply pressure in a straight line with the

bit. Use enough pressure to keep the drill bit

biting, but do not push hard enough to stall the

motor or deflect the bit.

4. Hold tool firmly with both hands to control the

twisting action of the drill.

5. IF DRILL STALLS, it is usually because it

is being overloaded. RELEASE TRIGGER

IMMEDIATELY, remove drill bit from work,

and determine cause of stalling. DO NOT

CLICK TRIGGER OFF AND ON IN AN

ATTEMPT TO START A STALLED DRILL –

THIS CAN DAMAGE THE DRILL.

6. Keep the motor running when pulling the bit

back out of a drilled hole. This will help prevent

jamming.

Screwdriver Operation (ﬁg. 3)

1. Select the desired speed/torque range using

the three-speed gear shifter (f) on the top of the

tool. If using the torque adjustment collar (e),

initially set the three-speed gear shifter to speed

2 or 3. This ensures control over the fastener

and allows the screw to be set to specification.

NOTE: Use the lowest torque setting (1) first

and increase the number through to the highest

setting (11) to seat the fastener at the desired

Belt Hook and Magnetic Bit Holder

(ﬁg. 1)

WARNING: To reduce the risk of

serious personal injury, turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories.

WARNING: To reduce the risk of

serious personal injury, DO NOT

suspend tool overhead or suspend

objects from the belt hook. ONLY hang

tool’s belt hook from a work belt.

WARNING: To reduce the risk of

serious personal injury, ensure the

screw holding the belt hook is secure.

IMPORTANT: When attaching or replacing the belt

hook or magnetic bit holder, use only the screw

(k) that is provided. Be sure to securely tighten the

screw.

The belt hook (j) and magnetic bit holder (l) can be

be attached to either side of the tool using only the

screw (k) provided, to accommodate left- or right-

handed users. If the hook or magnetic bit holder is

not desired at all, it can be removed from the tool.

To move belt hook or magnetic bit holder, remove

the screw (k) that holds it in place then reassemble

on the opposite side. Be sure to securely tighten the

screw.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

Proper Hand Position (ﬁg. 9)

WARNING: To reduce the risk of

serious personal injury, ALWAYS

use proper hand position as shown

in figure 9.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

English

13

depth. The lower the number, the lower the

torque output.

2. Reset the torque adjustment collar (e) to the

appropriate number setting for the torque

desired. Make a few practice runs in scrap or

unseen areas to determine the proper position

of the torque adjustment collar.

NOTE: The torque adjustment collar may be set to

any number at any time.

Hammerdrill Operation (ﬁg. 5)

1. Select the desired speed/torque range using

the gear shifter to match the speed and torque

to the planned operation. Set the torque

adjustment collar (e) to the hammer symbol.

2. Select the high speed 3 setting by sliding the

gear shifter (f) back (away form the chuck).

3. When drilling, use just enough force on the

hammer to keep it from bouncing excessively.

Prolonged and too much force on the hammer

will cause slower drilling speeds and potential

overheating.

4. Drill straight, keeping the bit at a right angle to

the work. Do not exert side pressure on the bit

when drilling as this will cause clogging of the

bit flutes and a slower drilling speed.

5. When drilling deep holes, if the hammer speed

starts to drop off, pull the bit partially out of

the hole with the tool still running to help clear

debris from the hole.

6. For masonry, use carbide-tipped bits or

masonry bits. A smooth, even flow of dust

indicates the proper drilling rate.

MAINTENANCE

Your DeWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

serious personal injury, turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories. An accidental start-up

can cause injury.

The charger and battery pack are not serviceable.

There are no serviceable parts inside.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect

the charger from the AC outlet before

cleaning. Dirt and grease may be

removed from the exterior of the charger

using a cloth or soft non-metallic brush.

Do not use water or any cleaning

solutions.

Optional Accessories

WARNING: Since accessories, other

than those offered by DeWALT, have

not been tested with this product, use

of such accessories with this tool could

be hazardous. To reduce the risk of

injury, only DeWALT recommended

accessories should be used with this

product.

Consult your dealer for further information on the

appropriate accessories.

Protecting the Environment

Separate collection. This product must

not be disposed of with normal

household waste.

Should you ﬁnd one day that your D

eWALT product

needs replacement, or if it is of no further use to you,

do not dispose of it with household waste. Make this

product available for separate collection.

English

14

Separate collection of used products

and packaging allows materials to be

recycled and used again. Re-use of

recycled materials helps prevent

environmental pollution and reduces

the demand for raw materials.

Local regulations may provide for separate collection

of electrical products from the household, at

municipal waste sites or by the retailer when you

purchase a new product.

DeWALT provides a facility for the collection and

recycling of DeWALT products once they have

reached the end of their working life. To take

advantage of this service please return your product

to any authorised repair agent who will collect them

on our behalf.

You can check the location of your nearest

authorised repair agent by contacting your local

DeWALT office at the address indicated in this

manual. Alternatively, a list of authorised DeWALT

repair agents and full details of our after-sales

service and contacts are available on the Internet at:

www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when

it fails to produce sufficient power on jobs which

were easily done before. At the end of its technical

life, discard it with due care for our environment:

 • Runthebatterypackdowncompletely,then

remove it from the tool.

 • Li-Ioncellsarerecyclable.Takethemtoyour

dealer or a local recycling station. The collected

battery packs will be recycled or disposed of

properly.

15

DCD932 DCD990

DCD937 DCD995

D EWALT D EWALT

DCD932 DCD937 DCD990 DCD995

14.4 14.4 18 18

2 2 2 2

1 / 0-420 0–420 0–450 0–450

2 / 0-1250 0–1250 0–1300 0–1300

3 / 0-1850 0–1850 0–2000 0–2000

1 / – 0–7140 – 0–7650

2 / – 0–21250 – 0–22100

3 / – 0–31450 – 0–34000

/

l

75/38 75/38 80/42 80/42

1.5–13 1.5–13 1.5–13 1.5–13

45 45 50 50

13 13 13 13

– 14 – 16

1.5 1.55 1.5 1.55

DCB140 DCB141 DCB142 DCB143

14.4 14.4 14.4 14.4

3.0 1.5 4.0 2.0

0.53 0.30 0.54 0.30

DCB180 DCB181 DCB182 DCB183

18 18 18 18

3.0 1.5 4.0 2.0

0.64 0.35 0.61 0.40

16

DCB105

220

30 40 55 70

1.5 2.0 3.0 4.0

0.49

a)

1)

2)

3)

b)

1)

2)

3)

4)

5)

6)

RCD

c)

1)

2)

17

3) /

4)

5)

6)

7)

d)

1)

2)

3)

4)

5)

6)

7)

e)

1)

2)

3)

4)

f)

a)

//

•



18

•

DEWALT

•

DEWALT

•

–

2013 XX XX

DCB105

ページが読み込まれています...

DeWalt DCD995 ユーザーマニュアル

DeWalt DCD995 ユーザーマニュアル

他の言語で

関連論文