DCF830
DCF835
DCF880
DCF885
2
Copyright DeWALT
English (original instructions) 03
13
22
31
1
Figure 1
Figure 2
h
i
b
a
g
e
f
g
c
d
g
e
f
k
j
i
l
m
l
DCF830, DCF880
DCB142 and DCB182 only
2
Figure 3
Figure 4
c
d
c
d
ENGLISH
3
CORDLESS IMPACT DRIVER / WRENCH
DCF830, DCF835, DCF880, DCF885
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make
DeWALT one of the most reliable partners for professional power tool users.
Technical Data
DCF830 DCF835 DCF880 DCF885
Voltage V 14.4 14.4 18 18
Battery Type Li-Ion Li-Ion Li-Ion Li-Ion
No load speed min
-1
0–2300 0–2800 0–2300 0–2800
Impact rate min
-1
0–2700 0–3200 0–2700 0–3200
Max torque Nm 185 150 203 155
Tool holder 1/2" square 1/4" hex 1/2" square 1/4" hex
(13 mm) (6.35 mm) (13 mm) (6.35 mm)
Weight (without battery pack) kg 1.01 0.93 1.01 0.93
Battery pack DCB140 DCB141 DCB142 DCB143
Battery type Li-Ion Li-Ion Li-Ion Li-Ion
Voltage V
DC
14.4 14.4 14.4 14.4
Capacity A
h
3.0 1.5 4.0 2.0
Weight kg 0.53 0.30 0.54 0.30
Battery pack DCB180 DCB181 DCB182 DCB183 DCB184
Battery type Li-Ion Li-Ion Li-Ion Li-Ion Li-Ion
Voltage V
DC
18 18 18 18 18
Capacity A
h
3.0 1.5 4.0 2.0 5.0
Weight kg 0.64 0.35 0.61 0.40 0.62
Charger DCB105
Mains voltage V
AC
220-240
Battery type Li-Ion
Approx. charging time min 30 40 55 70 90
(1.5 Ah (2.0 Ah (3.0 Ah (4.0 Ah (5.0 Ah
battery packs) battery packs) battery packs) battery packs) battery packs)
Weight kg 0.49
Charger DCB115
Mains voltage V
AC
220-240
Battery type Li-Ion
Approx. charging time min 30 40 55 70 90
(1.5 Ah (2.0 Ah (3.0 Ah (4.0 Ah (5.0 Ah
battery packs) battery packs) battery packs) battery packs) battery packs)
Weight kg 0.5
ENGLISH
4
Definitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of fire.
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result
in electric shock, fire and/or serious
injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
ENGLISH
5
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with another
battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery, avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Specific Safety Rules for
Impact Wrenches
• Hold power tool by insulated gripping
surfaces when performing an operation
where the fastener may contact hidden
wiring. Fasteners contacting a “live” wire may
make exposed metal parts of the power tool
“live” and could give the operator an electric
shock.
Residual Risks
In spite of the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
– Impairment of hearing.
– Risk of personal injury due flying particles.
– Risk of burns due to accessories becoming hot
during operation.
– Risk of personal injury due to prolonged use.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
DATE CODE POSITION
The Date Code, which also includes the year of
manufacture, is printed into the housing surface that
forms the mounting joint between tool and battery.
ENGLISH
6
Example:
2012 XX XX
Year of Manufacture
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual
contains important safety and operating instruc tions
for the DCB105 and DCB115battery charger.
• Beforeusingthecharger,readallinstructions
and cautionary markings on charger, battery
pack and product using the battery pack.
WARNING: Shock hazard. Do not allow
any liquid to get inside charger. Electric
shock may result.
CAUTION: Burn hazard. To reduce
the risk of injury, charge only DeWALT
rechargeable battery packs. Other types
of batteries may overheat and burst
resulting in personal injury and property
damage.
CAUTION: Children should be
supervised to ensure that they do not
play with the appliance.
NOTICE: Under certain conditions, with
the charger plugged in to the power
supply, the exposed charging contacts
inside the charger can be shorted by
foreign material. Foreign materials of
a conductive nature such as, but not
limited to, steel wool, aluminum foil or
any buildup of metallic particles should
be kept away from charger cavities.
Always unplug the charger from the
power supply when there is no battery
pack in the cavity. Unplug charger
before attempting to clean.
• DONOTattempttochargethebatterypack
with any chargers other than the ones in
this manual. The charger and battery pack are
specifically designed to work together.
• Thesechargersarenotintendedfor
any uses other than charging DeWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock or
electrocution.
• Donotexposechargertorainorsnow.
• Pullbyplugratherthancordwhen
disconnecting charger. This will reduce risk
of damage to electric plug and cord.
• Makesurethatcordislocatedsothatitwill
not be stepped on, tripped over or otherwise
subjected to damage or stress.
• Donotuseanextensioncordunlessit
is absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock or electrocution.
• When operating a charger outdoors, always
provide a dry location and use an extension
cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of
electric shock.
• Donotblocktheventilationslotsonthe
charger.Theventilationslotsarelocated
on the top and sides of the charger. Place
the charger in a position away from any heat
source.
• Donotoperatechargerwithdamagedcord
or plug — have them replaced immediately.
• Do not operate charger if it has received
a sharp blow, been dropped or otherwise
damaged in any way. Take it to an authorised
service centre.
• Donotdisassemblethecharger;takeitto
an authorised service centre when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution or
fire.
• Incaseofdamagedpowersupplycordthe
supply cord must be replaced immediately by
the manufacturer, its service agent or similar
qualified person to prevent any hazard.
• Disconnectthechargerfromtheoutlet
beforeattemptinganycleaning.Thiswill
reduce the risk of electric shock. Removing
the battery pack will not reduce this risk.
• NEVERattempt to connect 2 chargers together.
• Thechargerisdesignedtooperateon
standard220-240Vhouseholdelectrical
power. Do not attempt to use it on any other
voltage. This does not apply to the vehicular
charger.
SAVE THESE INSTRUCTIONS
Chargers
The DCB105 and DCB115charger accepts 10.8
V, 14.4 V and 18 V Li-Ion (DCB121, DCB123,
DCB140, DCB141, DCB142, DCB180, DCB181,
DCB182, DCB183 and DCB184) battery packs.
This charger requires no adjustment and is designed
to be as easy as possible to operate.
Charging Procedure (fig. 2)
1. Plug the charger into an appropriate 220-240 V
outlet before inserting the battery pack.
ENGLISH
7
2. Insert the battery pack (f) into the charger,
making sure the pack is fully seated in the
charger. The red (charging) light will blink
continuously indicating that the charging
process has started.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
NOTE: To ensure maximum performance and life of
Li-Ion batteries, fully charge the pack before first use.
Charging Process
Refer to the table below for the state of charge of
the battery pack.
Charge indicators: DCB105
charging –– –– –– ––
fully charged –––––––––––––––––
hot/coldpackdelay ––•––•––• ––•
x
problempackorcharger ••••••••••••
problempowerline ••••••••••••
Charge indicators: DCB115
charging
fully charged
hot/cold pack delay*
This charger will not charge a faulty battery pack.
The charger will indicate faulty battery by refusing to
light or by displaying problem pack or charger blink
pattern.
NOTE: This could also mean a problem with a
charger.
If the charger indicates a problem, take the charger
and battery pack to be tested at an authorised
service centre.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot
or too cold, it automatically starts a hot/cold pack
delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
XR Li-Ion tools are designed with an Electronic
Protection System that will protect the battery
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
Li-Ion battery on the charger until it is fully charged.
A cold battery pack will charge at about half the rate
of a warm battery pack. The battery pack will charge
at that slower rate throughout the entire charging
cycle and will not return to maximum charge rate
even if the battery warms.
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure
to include the catalog number and voltage.
The battery pack is not fully charged out of the
carton. Before using the battery pack and charger,
read the safety instructions below and then follow
the charging procedures outlined.
READ ALL INSTRUCTIONS
• Donotchargeorusethebatterypack
in explosive atmospheres, such as in the
presence of flammable liquids, gases or
dust. Inserting or removing the battery pack
from the charger may ignite the dust or fumes.
• Never force the battery pack into charger.
Do not modify the battery pack in any way
to fit into a non-compatible charger as
battery pack may rupture causing serious
personal injury.
• Chargethebatterypacksonlyindesignated
DeWALT chargers.
• DONOTsplash or immerse in water or other
liquids.
• Donotstoreorusethetoolandbattery
pack in locations where the temperature
may reach or exceed 40˚C (105°F) (such as
outside sheds or metal buildings in summer).
• Forbestresults,makesurethebatterypackis
fully charged before use.
WARNING: Never attempt to open
the battery pack for any reason. If
the battery pack case is cracked or
damaged, do not insert it into the
charger. Do not crush, drop or damage
battery pack. Do not use a battery
pack or charger that has received a
sharp blow, been dropped, run over
or damaged in any way (e.g., pierced
with a nail, hit with a hammer, stepped
on). Electric shock or electrocution may
result. Damaged battery packs should
be returned to the service centre for
recycling.
ENGLISH
8
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large
battery packs will stand upright on the
battery pack but may be easily knocked
over.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION
(Li-Ion)
• Donotincineratethebatterypackevenifit
is severely damaged or is completely worn
out. The battery pack can explode in a fire.
Toxic fumes and materials are created when
lithium ion battery packs are burned.
• Ifbatterycontentscomeintocontactwith
the skin, immediately wash the area with
mild soap and water. If the battery liquid gets
into the eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte
is composed of a mixture of liquid organic
carbonates and lithium salts.
• Contentsofopenedbatterycellsmaycause
respiratory irritation. Provide fresh air. If
symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid
may be flammable if exposed to spark
or flame.
Battery Pack
BATTERY TYPE
The DCF830 and DCF835 operate on 14.4 volt
battery packs.
The DCF880 and DCF885 operate on 18 volt battery
packs.
The DCB140, DCB141, DCB142, DCB180,
DCB181, DCB182, DCB183 or DCB184 battery
packs may be used. Refer to Technical Data for
more information.
Storage Recommendations
1. The best storage place is one that is cool and
dry away from direct sunlight and excess heat
or cold. For optimum battery performance and
life, store battery packs at room temperature
when not in use.
2. For long storage, it is recommended to store a
fully charged battery pack in a cool, dry place
out of the charger for optimal results.
NOTE: Battery packs should not be stored
completely depleted of charge. The battery pack will
need to be recharged before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual,
the labels on the charger and the battery pack show
the following pictographs:
Read instruction manual before use.
Battery charging.
Battery charged.
Hot/cold pack delay.
x
Problem pack or charger.
Problem powerline.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Use only with DeWALT battery packs.
Others may burst causing personal injury
and damage.
Do not expose to water.
Have defective cords replaced
immediately.
Charge only between 4°C and 40°C.
Discard the battery pack with due care for
the environment.
Do not incinerate the battery pack.
Charges Li-Ion battery packs.
See Technical Data for charging time.
Only for indoor use.
ENGLISH
9
Package Contents
The package contains:
1 Impact Driver / Wrench
1 Charger
2 Batteries
1 Bit clip ( Driver only )
1 Belt hook
1 Kitbox
1 Instruction manual
NOTE: Battery packs, chargers and kitboxes are not
included with N-models.
• Checkfordamagetothetool,partsor
accessories which may have occurred during
transport.
• Takethetimetothoroughlyreadand
understand this manual prior to operation.
Description (fig. 1, 4)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
a. Trigger switch
b. Forward/reverse button
c. Chuck collar
d. 6.35 mm (1/4") hex quick-release chuck
(DCF835, DCF885)
e. Battery release button
f. Battery pack
g. Worklight
h. Belt hook
i. Screw
j. Bit clip
k. Main handle
l. Anvil
m. Detent pin (DCF830, DCF880)
INTENDED USE
These heavy-duty impact wrenches/drivers are
designed for professional impact screwdriving
applications.
The impact function makes this tool particularly
useful for driving fasteners in wood, metal and
concrete.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
This impact driver is a professional power tool.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
• Thisproductisnotintendedforusebypersons
(including children) suffering from diminished
physical, sensory or mental abilities, or for lack
of experience and/or for want of knowledge or
skills unless they are supervised by a person
responsible for their safety. Children should
never be left alone to play with this product.
Electrical Safety
This tool is double insulated; therefore no
earth wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced
by the manufacturer or an authorised Black &
Decker Service Centre in order to avoid a hazard.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see Technical Data). The minimum conductor size
is 1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
WARNING: Use only DeWALT battery
packs and chargers.
Inserting and Removing the
Battery Pack from the Tool (fig. 2)
NOTE: For best results, make sure your battery
pack is fully charged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the battery pack (f) with the rails inside the
tool’s handle (fig. 2).
ENGLISH
10
2. Slide it into the handle until the battery pack is
firmly seated in the tool and ensure that it does
not disengage.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the battery release button (e) and firmly
pull the battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
FUEL GAUGE BATTERY PACKS (FIG. 2)
Some DeWALT battery packs include a fuel gauge
which consists of three green LED lights that
indicate the level of charge remaining in the battery
pack.
To actuate the fuel gauge, press and hold the fuel
gauge button (l). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
Belt Hook and Bit Clip (fig. 1)
WARNING: To reduce the risk of
serious personal injury, DO NOT
suspend tool overhead or suspend
objects from the belt hook. ONLY hang
tool’s belt hook from a work belt.
WARNING: To reduce the risk of
serious personal injury, ensure the
screw holding the belt hook is secure.
IMPORTANT: When attaching or replacing the
belt hook or bit clip, use only the screw (i) that is
provided. Be sure to securely tighten the screw.
The belt hook (h) and bit clip (j) can be be attached
to either side of the tool using only the screw (i)
provided, to accommodate left- or right- handed
users. If the hook or bit clip is not desired at all, it
can be removed from the tool.
To move belt hook or bit clip, remove the screw
(i) that holds it in place then reassemble on the
opposite side. Be sure to securely tighten the screw.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
Proper Hand Position (fig. 1, 4)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the main
handle (k).
Variable Speed Trigger Switch (fig. 1)
To turn the tool on, squeeze the trigger switch (a). To
turn the tool off, release the trigger switch. Your tool
is equipped with a brake. The chuck will stop when
the trigger switch is fully released.
The variable speed switch enables you to start
the application at a slow speed. The further you
squeeze the trigger, the faster the tool will operate.
For maximum tool life, use variable speed only for
starting holes or fasteners.
NOTE: Continuous use in variable speed range is
not recommended. It may damage the switch and
should be avoided.
Forward/Reverse Control Button
(fig. 1)
A forward/reverse control button (b) determines the
direction of the tool and also serves as a lock-off
button.
To select forward rotation, release the trigger switch
and depress the forward/reverse control button on
the right side of the tool.
To select reverse, depress the forward/reverse
control button on the left side of the tool. The center
position of the control button locks the tool in the off
position. When changing the position of the control
button, be sure the trigger is released.
NOTE: The first time the tool is run after changing the
direction of rotation, you may hear a click on start up.
This is normal and does not indicate a problem.
ENGLISH
11
Worklights (fig. 1)
There are three worklights (g) located around the
chuck collar (c). The worklights will be activated
when the trigger switch is squeezed.
When the trigger is released the worklight will stay
illuminated for up to 20 seconds.
NOTE: The worklights are for lighting the immediate
work surface and are not intended to be used as a
flashlight.
Quick-Release Chuck (fig. 1, 3)
DCF835, DCF885
NOTE: The chuck accepts 6.35mm (1/4") hex
accessories and 25.4mm (1") bit tips only. Using
25.4mm (1") bits allows better access in tight
spaces.
Place the forward/reverse button (b) in the locked
off (center) position or remove battery pack before
changing accessories.
To install an accessory, push accessory to fully insert
into chuck. The chuck collar does not need to be
pulled up to lock accessory in place.
To remove an accessory, pull the chuck collar away
from the front of the tool. Remove the accessory
and release the collar.
Anvil with Detent Pin (Fig. 1)
DCF830, DCF880
Place the switch in the locked off (center) position or
remove battery pack before changing accessories.
To install a socket on the anvil, align the hole in the
side of the socket with the detent pin (m) on the
anvil (l). Press the socket on until the detent pin
engages in the hole. Depression of detent pin may
be necessary to aid installation of socket.
To remove a socket, depress the detent pin through
the hole and pull the socket off.
WARNING: Use only impact sockets.
Non-impact sockets may break and
cause a hazardous condition. Inspect
sock et prior to use to ensure that it
contains no cracks.
Usage
Your impact tool generates the following maximum
torque:
Cat # Ft.-Lbs. In.-Lbs. Nm
DCF830 135 1620 185
DCF835 111 1330 150
DCF880 150 1800 203
DCF885 114 1400 155
CAUTION: Ensure fastener and/or
system will withstand the level of torque
generated by the tool. Excessive torque
may cause breakage and possible
personal injury.
1. Place the socket on the fastener head. Keep
the tool pointed straight at the fastener.
2. Press switch to start operation. Release the
switch to stop operation. Always check torque
with a torque wrench, as the fastening torque is
affected by many factors including the following:
• Voltage: Low voltage, due to a nearly
discharged battery, will reduce fastening
torque.
• Socket size: Failure to use the correct
socket size will cause a reduction in fastening
torque.
• Bolt Size: Larger bolt diameters generally
require higher fastening torque. Fastening
torque will also vary according to length,
grade, and torque coefficient.
• Bolt: Ensure that all threads are free of rust
and other debris to allow proper fastening
torque.
• Material: The type of material and surface
finish of the material will affect fastening
torque.
• Fastening Time: Longer fasten ing time
results in increased fastening torque. Using
a longer fastening time than recom mended
could cause the fasteners to be overstressed,
stripped or damaged.
MAINTENANCE
Your DeWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
The charger and battery pack are not serviceable.
There are no serviceable parts inside.
Lubrication
Your power tool requires no additional lubrication.
ENGLISH
12
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
Optional Accessories
WARNING: Since accessories, other
than those offered by DeWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DeWALT recommended
accessories should be used with this
product.
WARNING: To reduce the risk of
injury, only use DeWALT impact-ready
accessories.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your DeWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products
and packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
DeWALT provides a facility for the collection and
recycling of DeWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
DeWALT office at the address indicated in this
manual. Alternatively, a list of authorised DeWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when
it fails to produce sufficient power on jobs which
were easily done before. At the end of its technical
life, discard it with due care for our environment:
• Runthebatterypackdowncompletely,then
remove it from the tool.
• Li-Ioncellsarerecyclable.Takethemtoyour
dealer or a local recycling station. The collected
battery packs will be recycled or disposed of
properly.
13
中文简体
充电式冲击起子 ／ 扳手
DCF830、DCF835、DCF880、DCF885
恭喜！
恭喜您选择了 DeWALT 工具。凭借多年的经验和产品开发及创新方面的不断努力，DeWALT 已经成为专
业电动工具使用者最可靠的合作伙伴之一。
技术参数
DCF830 DCF835 DCF880 DCF885
V 14.4 14.4 18 18
min
-1
0–2300 0–2800 0–2300 0–2800
min
-1
0–2700 0–3200 0–2700 0–3200
Nm 185 150 203 155
1/2" 1/4" 1/2" 1/4"
(13 mm) (6.35 mm) (13 mm) (6.35 mm)
重量（不含电池组） kg 1.01 0.93 1.01 0.93
DCB140 DCB141 DCB142 DCB143
V
DC
14.4 14.4 14.4 14.4
A
h
3.0 1.5 4.0 2.0
0.53 0.30 0.54 0.30
DCB180 DCB181 DCB182 DCB183 DCB184
V
DC
18 18 18 18 18
A
h
3.0 1.5 4.0 2.0 5.0
0.60 0.35 0.61 0.40 0.62
DCB105
220
30 40 55 70 90
(1.5 Ah 2.0 Ah 3.0 Ah 4.0 Ah 5.0 Ah
0.49
DCB115
220
30 40 55 70 90
(1.5 Ah 2.0 Ah 3.0 Ah 4.0 Ah 5.0 Ah
0.5
14
中文简体
定义：安全准则
下列定义解释了各警示词的严重程度。请仔细阅读
本手册，并注意警示符号的出现。
危险：表示存在紧急的危险情况，如果不
加以避免，则可能导致死亡或严重伤害。
警告：表示存在潜在的危险情况，如果不
加以避免，则可能导致死亡或严重伤害。
警示：表示存在潜在的危险情况，如果不
加以避免，则可能导致轻度或中度伤害。
注意：表示不涉及人身伤害的情况，如
果不加以避免，可能导致财产损失。
表示存在触电的危险。
表示存在火灾的危险。
警告：为了减少受伤的危险，请阅读使
用手册。
电动工具一般安全警告
警告！请仔细阅读所有安全警告和指示
说明。如果不遵守下列警告和指示，则
可能会导致触电，火灾和/或严重伤害的
危险。
请保存所有警告和指示，
以备将来查阅。
警告中的术语 “电动工具” 是指由市电驱动时（有
线）电动工具，或由电池驱动时（无线）电动工
具。
1) 工作场地
a)
保持工作场地清洁和明亮。混乱和黑暗的场
地会引发事故。
b)
不要在易爆环境，如有易燃液体、气体或粉
尘的环境下操作电动工具。电动工具产生的
火花会点燃粉尘或气体。
c)
让儿童和旁观者离开后操纵电动工具。分心
会使你放松控制。
2) 电气安全
a)
电动工具的插头必须与插座相配。绝不能以
任何方式改装插头。需接地的电动工具不能
使用任何转换插头。未经改装的插头和相配
的插座将减少触电危险。
b)
避免人体接触接地表面，如管道、散热片、
和冰箱。如果你身体接地会增加触电危险。
c)
不得将电动工具暴露在雨中或潮湿环境中。
水进入电动工具将增加触电危险。
d)
不得滥用电线。绝不能用电线搬运、拉动电
动工具或拔出其插头。让电动工具远离热、
油、锐边或运动部件。受损或缠绕的电线会
增加触电危险。
e)
当在户外使用电动工具时，使用适合户外使
用的外接电线。适合户外使用的电线将减少
触电危险。
f)
如果必须在潮湿场合使用电动工具，请使用
漏电保护装置 (RCD)。使用漏电保护装置可
减少触电的危险。
3) 人身安全
a)
保持警觉。当操作电动工具时关注所从事的
操作并保持清醒。切勿在疲倦，药物、酒精
或治疗反应下操作电动工具。在操作电动工
具期间精力分散会导致严重人身伤害。
b)
使用安全装置。始终佩戴护目镜。安全装
置，诸如适当条件下的防尘面具、防滑安全
鞋、安全帽、听力保护等装置能减少人身伤
害。
c)
避免突然起动。确保开关在插入插头时处于
关断位置。手指放在已接通电源的开关上或
开关处于接通状态时插入插头可能会导致危
险。
d)
在电动工具接通之前，拿掉所有调节钥匙或
扳手。遗留在电动工具旋转零件上的扳手可
能会导致人身伤害。
e)
手脚不要伸得太长。时刻注意脚下和身体平
衡。这样在意外情况下才能更好地控制电动
工具。
f)
着装适当。不要穿宽松衣服或佩戴饰品。
让您的头发、衣服和手套远离运动部件。
宽松衣服、佩饰或长发可能会卷入运动
部件。
g)
如果提供了与排屑装置、集尘设备连
接用的装置，请确保他们连接完好且使
用得当。使用这些装置可减少碎屑引起的
危险。
4) 电动工具的使用以及注意事项
15
中文简体
a)
不要滥用电动工具。根据用途使用适当的电
动工具。使用适当的设计额定值的电动工具
会使你工作更有效、更安全。
b)
若开关不能接通或关断电源工具，则不能使
用该电动工具。不能用开关来控制的电动工
具是危险的且必须进行修理。
c)
在执行任何调整、更换附件或贮存电动工具
之前，必须从电源上拔掉插头和／或将电池
盒脱开电源。这种防护性措施将减少电动工
具突然起动的风险。
d)
将闲置的电动工具贮存在儿童所及范围之
外，并且不要让不熟悉电动工具或对这些说
明不了解的人操作电动工具。电动工具在未
经培训的用户手中是危险的。
e)
保养电动工具。检查运动件的安装偏差或卡
住、零件破损情况和影响电动工具运行的其
他条件。如有损坏，电动工具必须在使用前
修理好。许多事故由维护不良的电动工具引
发。
f)
保持刀具锋利和清洁。保养良好的有锋利切
削刃的刀具不易卡住而且容易控制。
g)
按照使用说明书以及打算使用的电动工
具的特殊类型要求的方式，考虑作业
条件和进行的作业来使用电动工具、
附件和工具的刀头等。将电动工具用
作那些与要求不符的操作可能会导致
危险情况。
5) 电池工具的使用以及注意事项
a)
确保开关在插入电池盒前处于断开状态。将
电池盒插入到开关状态为接通的电动工具上
会引发事故。
b)
只用由制造商规定的充电器充电。将适用于
某种电池盒的充电器用到其他电池盒时会发
生着火危险。
c)
只使用配有特制电池盒的电动工具。使用
其他电池盒会发生损坏盒着火危险。
d)
当电池盒不用时，将它远离其他金属物
品，例如回形针、硬币、钥匙、钉子、螺
钉或其他小金属物品，以防一端与另一端
连接。电池端部短路会引起燃烧或火灾。
e)
在滥用条件下，液体会从电池中溅出；避
免接触。如果无意间碰到了，用水冲洗。
如果液体碰到眼睛，还要寻求医疗帮助。
从电池中溅出的液体会发生腐蚀或燃烧。
6) 维修
a)
让专业维修人员使用特定备件维修电动工
具。这将保证所维修的电动工具的安全。
冲击扳手的附加安全说明
•
操作过程中紧固件可能接触隐藏的电线时，请
握住工具的绝缘表面。紧固件接触带电电线可
能使电动工具外露的金属部件带电，因而导致
操作人员触电。
剩余风险
尽管遵守了相关的安全法规并采用安全装备，某些
剩余风险仍然是无法避免的。这些风险包括：
–
听力损伤。
–
四射的物品引起的人身伤害。
–
操作过程中配件加热而产生的烧伤危险。
–
长时间的使用引起的人身伤害。
工具上的标识
工具上有下列标志：
使用前请仔细阅读使用手册。
日期代码位置
连接工具和电池之间的外壳表面印有日期代码，日
期代码包括制造年份。
例如：
2012 XX XX
制造年份
针对所有电池充电器的重要安全
说明
请妥善保存这些说明：本手册包含重要的 DCB105
和 DCB115 电池充电器安全和操作说明。
•
使用充电器之前，请阅读所有说明和充电器、
电池组以及电池组产品上的警示标记。
警告：触电危险。禁止让任何液体进入
充电器，否则会引起触电。
警示：烧伤危险。为了减少受伤的危
险，只使用
DeWALT
充电式电池组充
电。其它类型的电池可能会过热爆裂，
造成人身伤害和财产损失。
16
中文简体
警示：监督儿童以确保他们不把设备当
玩具。
注意：在某些情况下，充电器连接电源
时，异物可能会连接充电器内的外露充
电接触点而造成短路。请勿让能导电的
异物靠近充电器内，这些异物包括但不
限于钢棉、铝箔或任何金属颗粒的堆积
物。充电器中没有电池组时，请断开充
电器和电源。清洗前请拔掉充电器。
•
禁止使用本手册指定充电器以外的其他任何充
电器为电池组充电。充电器和电池组是专门设
计的，具有兼容性。
•
除了为
DeWALT
充电式电池充电以外，这些
充电器都不能用于其他任何用途。否则可能会
导致火灾、电击或触电。
•
请勿将充电器暴露于雨中或雪中。
•
断开充电器时应拔下插头，切勿拉拽电线。这
将减少电源插头和电源线损坏的风险。
•
确保电源线布置在不易踩踏、踢绊、拉扯或会
受到损害或压力的位置。
•
非绝对必要条件下禁止使用延长线。使用延长
线不当可能会导致火灾、触电或电击的危险。
•
户外操作充电器时，要保持干燥，使用适合户
外使用的延长线。适合户外使用的电线会减少
触电的危险。
•
禁止堵塞充电器上的通风槽。通风槽位于充电
器的顶部和两侧。充电器应远离所有热源。
•
禁止使用电源线或插头损坏的充电器，请立即
更换损坏的充电器。
•
禁止使用受过重击、掉落或以其他方式受损的
充电器。请将损坏的充电器送到授权的服务中
心维修。
•
请勿拆卸充电器，请将需要维修或服务的充电
器送到授权的服务中心。不正确的重装可能会
引起触电、电击或火灾的危险。
•
损坏的电源线必须立即由制造商、服务代理或
类似的合格人员进行更换以防止安全隐患。
•
清洁前请将充电器和插座断开以减少触电的危
险。仅取出电池不会减少触电风险。
•
切勿将两个充电器连接在一起。
•
充电器额定电力是标准
220
伏特家用电压。禁
止在任何其他电压下使用充电器。这条规则不
适用于车载充电器。
请妥善保存这些说明
充电器
DCB105 和 DCB115充电器适用于：10.8 V、
14.4 V 和 18 V 的锂离子（DCB121、DCB123、
DCB140、DCB141、DCB142、DCB180、
DCB181、DCB182、DCB183 和 DCB184）
电池组。
该充电器无需调整，专为简易操作而设计。
充电程序（图 2）
1. 插入电池组前请将充电器插入到合适的 220 伏
特插座。
2. 将电池组（f）插入到充电器中，确定电池组完
全就位。红色（充电中）指示灯将不断闪烁，
表示充电过程已经开始。
3. 红色灯持续亮起表示充电完成。此时电池组已
完全充电，您可以使用电池组或将电池组留在
充电器上。
注：为了确保锂离子电池的最佳性能和寿命，在首
次使用电池组之前必须将它完全充电。
充电程序
关于电池组的充电状态，请参阅下表。
充电状态:DCB105
–– –– –– ––
–––––––––––––––––
/ ––•––•––• ––•
x
••••••••••••
••••••••••••
充电状态:DCB115
/*
这个充电器不能为故障电池组充电。充电器指示灯
不亮或 “故障电池组或充电器” 指示灯闪烁时，表示
电池有故障。
注意：这也可能意味充电器有故障。
如果充电器提示有故障存在，请将充电器和电池组
送到授权的服务中心进行测试。
热/冷电池组延迟
当充电器检测到电池过热或过冷时，它会自动启动
热/冷电池延迟模式，暂停充电，直到电池达到适当
的温度。然后，充电器会自动切换到电池组充电模
式。此功能可确保电池拥有最长的使用寿命。
XR 锂电池工具的设计带有防止电池超载、过热或
深度放电的电子保护系统。
如果电子保护系统处于运作状态，该工具将自动停
17
中文简体
止运转。如果发生这种情况，请将锂电池放在充电
器上直到完全充电。
冷电池组充电速率是温热的电池组充电速率的一半
左右。电池组在整个充电周期的充电速度都会较
慢，即使电池升温也不会返回到最高速度。
针对所有电池组的重要安全说明
在订购替换电池组时，请务必附上目录号码和电压。
货箱中的电池组是未完全充电的。在使用电池组和
充电器之前，请阅读下面的安全说明，然后按照充
电程序进行操作。
请阅读所有说明。
•
禁止在易爆环境中充电或使用电池组，如有易
燃液体、气体或粉尘的环境。插入或取出电池
组时可能会点燃粉尘或烟雾。
切勿将电池组强行插入充电器。禁止以任何方
式改装电池组并将电池组插入不兼容的充电
器，这种操作可能会导致电池组破裂，造成严
重的人身伤害。
•
只使用指定的
DeWALT
充电器为电池组充电。
•
禁止把电池组浸泡在水或其他液体中，或泼洒
水或其他液体到电池组上。
•
禁止在温度可能达到或超过
40°C
（
105°F
）的
地方（如夏天户外的棚子或金属建筑物中）存
储或使用工具和电池组。
•
为达到最佳效果，请确保电池组在使用前完全
充电。
警告：无论任何理由，都禁止打开电
池组。电池组外壳破裂或损坏时，禁
止将电池组插入充电器。请勿挤压、
掉落或损坏电池组。禁止使用受过强
烈重击、掉落、碾压或以任何其他
方式（如被钉子穿破、受到锤子的重
击、踩踏）受损的电池组或充电器。
否则会引起触电或电击。损坏的电池
组应交回服务中心回收。
警示：在不使用时，请将工具放置在不
会引起人摔倒的稳定表面上。一些具
有大型电池组的工具可以直立于电池组
上，但很容易被撞翻。
锂离子电池的安全说明
•
即使在电池组严重受损或完全磨损的情况下，
也请勿焚烧电池组。电池组可能会在火中爆
炸。锂离子电池组在燃烧时会释放有毒气体和
物质。
•
如果皮肤接触到电池内含物质，请立即用温和
肥皂和水冲洗接触的地方。如果电池液进入眼
睛，应睁开眼睛用清水冲洗至少 15 分钟或直
到刺激感消失。如果需要医疗救助，请告知医
护人员：电池电解质是由液状有机碳酸盐和锂
盐的混合物组成。
•
电池里的成分可能导致呼吸道刺激。此时请保
持空气流通。如果症状仍然存在，请就医。
警告：烧伤危险。电池液如果接触到火
花或火焰可能会燃烧。
电池组
电池类型
DCF830 和 DCF835 使用 14.4 伏特电池组。
DCF880 和 DCF885 使用 18 伏特电池组。
DCB140、DCB141、DCB142、DCB180、
DCB181 、DCB182、DCB183 或 DCB184 电池组
都可以使用。更多信息，
请参阅技术参数
。
存储建议
1. 最好将电池存放在阴凉、干燥、远离阳光直
射、不会过热或过冷的地方。为了获得最佳的
电池性能和使用寿命，在不使用时请将电池组
存储在室温下。
2. 长期存储时，建议将完全充电的电池组从充电
器取出，存储在阴凉、干燥的地方，以达到电
池组的最佳性能。
注意：电池组存储时不能处于电荷完全耗尽的状
态。在使用电池组之前，电池组必须重新充电。
充电器和电池组上的标签
除了在本手册中使用的标志，充电器和电池组的标
签还包括：
使用前请仔细阅读使用手册。
电池充电中。
电池完成充电。
热/冷电池组延迟。
x
故障电池组或充电器。
故障电源线。
禁止使用导电物体碰触。
18
中文简体
禁止对损坏的电池组充电。
只使用 DeWALT 电池组。其他电池组可
能会爆炸，造成人身伤害和损害。
禁止暴露于水中。
电线故障，请立即更换。
只在 4℃ 和 40℃ 之间的温度下充电。
废弃电池组请回收。
禁止焚烧电池组。
锂离子电池组充电。
充电时间，请参阅
技术参数
。
只能在室内使用。
包装内容
本产品包装内含有：
1 个冲击起子/扳手
1 个充电器
2 个电池
1 个起子头夹具（只适用于冲击起子）
1 个皮带扣
1 个工具箱
1 份使用手册
注：N-型号不包括电池组、充电器和维修箱。
•
检查工具、部件或配件是否在运输过程中损坏。
•
操作前请花时间仔细阅读和理解本手册。
说明（图 1、4）
警告：禁止改装电动工具或其任何部
分。否则可能导致损失或人身伤害。
a. 触发开关
b. 正转/反转控制按钮
c. 夹具环
d. 6.35 mm (1/4") 六角形快速释放夹头 (DCF835、
DCF885)
e. 电池释放按钮
f. 电池组
g. 工作灯
h. 皮带扣
i. 螺钉
j. 起子头夹具 (DCF835、DCF885)
k. 主握柄
l. 铁砧
m. 定位销 (DCF830、DCF880)
预期用途
这些冲击起子／扳手是为专业冲击钻孔、紧固等应
用而设计的。
冲击功能使这个工具非常有用，特别是在木材、金
属和混凝土中钻紧固件这方面。
请勿在潮湿环境中或在有易燃液体或气体的环境中
使用本工具。
冲击起子是专业的电动工具。请勿让儿童接触工
具。缺乏经验的操作员需要在监督下使用此工具。
• 本产品不适合身体、感官或心智能力有缺陷以
及缺乏经验、知识或技能的人员（包括儿童）
使用，除非有人负责他们的安全监督。请勿在
无人监管的情况下让儿童触及本产品。
电气安全
本设备为双重绝缘，因此无须接地线。
请务必确认电源电压是否与标牌上标明
的电压一致。
警 告 ： 如电源线损坏，必须用一条通过
服务部门购得的专门制备软线来更换。
如电源线由具备同等资格但未经史丹利授权的人士
更换，则产品质保将无效。
使用延长线
除非绝对必要，否则请勿使用延长线。使用与您的充
电器输入功率相符的合格延长线（见
技术参数
）。
导线的最小尺寸为 1mm
2
，最大长度为 30m。
当使用电缆卷筒时，请务必完全卷出电缆。
组装和调整
警告：为了减少严重人身伤害的危险，
调整或拆卸/安装附件或配件之前，请
将正转/反转控制按钮锁定在关闭位
置，或请务必关闭工具电源，断开电
池组。意外启动容易导致严重的人身
伤害。
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
DeWalt DCF835C2 ユーザーマニュアル
- カテゴリー
- パワーツール
- タイプ
- ユーザーマニュアル
他の言語で
- English: DeWalt DCF835C2 User manual