Hach TU5200 Basic User Manual

DOC022.97.80488

TU5200

03/2017, Edition 3

Basic User Manual

Manuel d'utilisation de base

Manual básico del usuario

Manual Básico do Usuário

基本用户手册

基本取扱説明書

기본 사용 설명서

คู่มือผู้ใช้เบื้องต้น

English..............................................................................................................................3

Français......................................................................................................................... 23

Español.......................................................................................................................... 43

Português...................................................................................................................... 64

中文................................................................................................................................. 85

日本語........................................................................................................................... 104

한글............................................................................................................................... 124

ไทย.................................................................................................................................. 144

2

Table of contents

Specifications on page 3 Operation on page 12

General information on page 4 Calibration on page 20

Installation on page 9 Maintenance on page 20

User interface and navigation on page 10 Troubleshooting on page 22

Startup on page 11

Additional information

An expanded user manual is available on the manufacturer's website. Videos on how to install,

operate and do maintenance and troubleshooting on the TU5200 turbidimeter are available on the

TU5 Series Turbidimeters playlist at http://www.youtube.com/user/hachcompany.

Specifications

Specifications are subject to change without notice.

Specification Details

Measurement method Nephelometry with the scattered light collected at a 90° angle to the incident light

and 360° around the sample vial.

Primary compliance method EPA approved Hach Method 10258

1

Dimensions (W x D x H) 41 x 28 x 12.5 cm (16 x 11 x 7.7 in.)

Weight 2.37 kg (5.23 lb)

Enclosure IP20

Protection class Instrument: III; Power supply: II

Pollution degree 2

Installation category II

Power requirements Instrument: 15 VDC, 2 A; Power supply: 100 to 240 VAC, 50/60 Hz

Operating temperature 10 to 40 °C (50 to 104 °F)

Storage temperature –30 to 60 °C (–22 to 140 °F)

Humidity 5 to 95% relative humidity, non-condensing

Display 17.8 mm (7 in.) color touch screen

Laser Class 2 laser product: Contains a non user-serviceable class 2 laser.

Optical light source 650 nm, maximum 0.43 mW

Measurement units NTU, FNU, TE/F, FTU, EBC, mg/L, mNTU

2

or mFNU

Range 0 to 700 NTU, FNU, TE/F, FTU; 0 to 100 mg/L; 0 to 175 EBC

Accuracy ± 2% of reading plus 0.01 NTU from 0 to 40 NTU

± 10% of reading from 40 to 700 NTU based on Formazin primary standard at

25 °C (77 °F)

Linearity Better than 1% for 0 to 40 NTU on Formazin at 25 °C (77 °F)

1

http://www.hach.com

2

1 mNTU = 0.001 NTU

English 3

Specification Details

Precision < 40 NTU: 0.002 NTU or 1% (the larger value); > 40 NTU: 3.5% based on

Formazin primary standard at 25 °C (77 °F)

Stray light < 0.01 NTU

Calibration options StablCal

®

: 1-point calibration (20 NTU) for 0 to 40 NTU measurement range; 2-

point calibration (20 and 600 NTU) for 0 to 700 NTU (full) measurement range

Formazin: 2-point calibration (20 NTU and dilution water) for 0 to 40 NTU

measurement range; 3-point calibration (20 NTU, 600 NTU and dilution water) for

0 to 700 NTU (full) measurement range

Degrees: 3-point calibration (20 and 100 mg/L and dilution water) for 0 to 100 mg/L

(full) measurement range

SDVB: 3-point calibration (20 NTU, 600 NTU and dilution water) for 0 to 700 NTU

(full) measurement range

Custom: 2- to 6-point custom calibration for a measurement range of 0 NTU to the

highest calibration point.

Verification options Glass verification rod (secondary turbidity standard) < 0.1 NTU, StablCal or

Formazin (0.1 to 40 NTU)

Verification (RFID or

Link2SC

®

)

Process and laboratory measurements are compared with RFID or Link2SC for

verification of the measurement value.

Certifications CE compliant; US FDA accession number: 1420493-xxx. This product complies

with IEC/EN 60825-1 and to 21 CFR 1040.10 in accordance with Laser Notice No.

50. Australian RCM.

Warranty 1 year (EU: 2 years)

General information

In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential

damages resulting from any defect or omission in this manual. The manufacturer reserves the right to

make changes in this manual and the products it describes at any time, without notice or obligation.

Revised editions are found on the manufacturer’s website.

Safety information

N O T I C E

The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,

without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent

permitted under applicable law. The user is solely responsible to identify critical application risks and install

appropriate mechanisms to protect processes during a possible equipment malfunction.

Please read this entire manual before unpacking, setting up or operating this equipment. Pay

attention to all danger and caution statements. Failure to do so could result in serious injury to the

operator or damage to the equipment.

Make sure that the protection provided by this equipment is not impaired. Do not use or install this

equipment in any manner other than that specified in this manual.

Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or serious injury.

W A R N I N G

Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death or serious

injury.

4 English

C A U T I O N

Indicates a potentially hazardous situation that may result in minor or moderate injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument. Information that requires special

emphasis.

Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or damage to the instrument

could occur if not observed. A symbol on the instrument is referenced in the manual with a

precautionary statement.

Electrical equipment marked with this symbol may not be disposed of in European domestic or public

disposal systems. Return old or end-of-life equipment to the manufacturer for disposal at no charge to

the user.

This symbol, if noted on the instrument, references the instruction manual for operation and/or safety

information.

This symbol indicates that a risk of electrical shock and/or electrocution exists.

This symbol indicates the need for protective eye wear.

This symbol indicates a laser device is used in the equipment.

This symbol identifies a risk of chemical harm and indicates that only individuals qualified and trained

to work with chemicals should handle chemicals or perform maintenance on chemical delivery

systems associated with the equipment.

This symbol indicates radio waves.

Class 2 laser product

D A N G E R

Personal injury hazard. Never remove covers from the instrument. This is a laser-based instrument and

the user risks injury if exposed to the laser.

English 5

Class 2 laser product, IEC60825-1:2014, 650 nm, maximum 0.43 mW

Location: Rear of the instrument.

Conforms to U.S. regulations 21 CFR 1040.10 and 1040.11 in

accordance with Laser Notice No. 50.

Location: Rear of the instrument.

Caution—Class 2 laser radiation when the lid is open. Do not look

into the laser beam.

Location: Top of the vial compartment.

This instrument is a Class 2 Laser product. There is only visible laser radiation when the instrument

is defective and when the instrument lid is open. This product complies with EN 61010-1, "Safety

Requirements for Electrical Equipment for Measurement, Control and Laboratory Use" and with

IEC/EN 60825-1, "Safety of Laser Products" and with 21 CFR 1040.10 in accordance with Laser

Notice No. 50. Refer to the labels on the instrument that supply laser information.

RFID module

Instruments with the optional RFID module receive and transmit information and data. The RFID

module operates with a frequency of 13.56 MHz.

RFID technology is a radio application. Radio applications are subject to national conditions of

authorization. The use of instruments with the optional RFID module is currently permitted in the

regions that follow:

EU (European Union) countries, EFTA (European Free Trade Association) countries, Turkey, Serbia,

Macedonia, Australia, Canada, US, Chile, Ecuador, Venezuela, Mexico, Brazil, South Africa, India,

Singapore, Argentina, Columbia, Peru and Panama

The use of instruments with the optional RFID module outside of the above-mentioned regions can

violate national laws. The manufacturer reserves the right also to get authorization in other countries.

In case of doubt, contact the manufacturer.

Safety information for RFID modules

W A R N I N G

Multiple hazards. Do not disassemble the instrument for maintenance. If the internal components must

be cleaned or repaired, contact the manufacturer.

W A R N I N G

Electromagnetic radiation hazard. Do not use the instrument in dangerous environments.

N O T I C E

This instrument is sensitive to electromagnetic and electromechanical interference. These interferences can have

an effect on the analysis performance of this instrument. Do not put this instrument near equipment that can

cause interference.

6 English

Obey the safety information that follows to operate the instrument in accordance with local, regional

and national requirements.

• Do not operate the instrument in hospitals and equivalent establishments or near medical

equipment, such as pace makers or hearing aids.

• Do not operate the instrument near highly flammable substances, such as fuels, highly flammable

chemicals and explosives.

• Do not operate the instrument near combustible gases, vapors or dust.

• Keep the instrument away from strong vibration or shock.

• The instrument can cause interference in immediate proximity to televisions, radios and

computers.

• The warranty does not cover improper use or wear.

FCC conformance for RFID

This instrument may contain a registered radio frequency identification device (RFID). Refer to

Table 1 for the Federal Communications Commission (FCC) registration information.

Table 1 Registration information

Parameter Value

FCC identification number (FCC ID) YUH-QR15HL

IC 9278A-QR15HL

Frequency 13.56 MHz

Certification

Canadian Radio Interference-Causing Equipment Regulation, IECS-003, Class A:

Supporting test records reside with the manufacturer.

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numérique de classe A répond à toutes les exigences de la réglementation canadienne

sur les équipements provoquant des interférences.

FCC Part 15, Class "A" Limits

Supporting test records reside with the manufacturer. The device complies with Part 15 of the FCC

Rules. Operation is subject to the following conditions:

1. The equipment may not cause harmful interference.

2. The equipment must accept any interference received, including interference that may cause

undesired operation.

Changes or modifications to this equipment not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment. This equipment has been tested

and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user will be required to

correct the interference at their expense. The following techniques can be used to reduce

interference problems:

1. Disconnect the equipment from its power source to verify that it is or is not the source of the

interference.

2. If the equipment is connected to the same outlet as the device experiencing interference, connect

the equipment to a different outlet.

3. Move the equipment away from the device receiving the interference.

English

7

4. Reposition the receiving antenna for the device receiving the interference.

5. Try combinations of the above.

Product overview

The TU5200 turbidimeter measures low turbidity mostly in finished drinking water applications. This

laboratory instrument is factory calibrated and measures scattered light at an angle of 90° in a 360°

radius around the axis of the incident light beam. Use the touch screen to operate the instrument.

Refer to Figure 1.

An optional RFID module is available. Figure 1 shows the RFID module. The RFID module lets

process and laboratory turbidity measurements be easily compared.

Videos on how to install, operate and do maintenance and troubleshooting on the

TU5200 turbidimeter are available on the TU5 Series Turbidimeters playlist at

http://www.youtube.com/user/hachcompany.

For the accessories, refer to the expanded user manual on the manufacturer's website.

Figure 1 Product overview

1 Lid 6 USB port type A

2 Vial compartment 7 USB port type B

3 Display 8 Ethernet port for LAN connection

4 Power button 9 RFID module indicator (optional)

5 Power supply connection 10 USB port type A

Product components

Make sure that all components have been received. Refer to Figure 2. If any items are missing or

damaged, contact the manufacturer or a sales representative immediately.

8

English

Figure 2 Product components

1 TU5200 4 Power supply with adapters

2 StablCal kit, sealed vials with RFID (10, 20 and

600 NTU)

5 Dust cover

3 Sample vials 6 Vial stand

Installation

C A U T I O N

Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the

document.

This instrument is rated for an altitude of 3100 m (10,710 ft) maximum. Use of this instrument at an

altitude higher than 3100 m can slightly increase the potential for the electrical insulation to break

down, which can result in an electric shock hazard. The manufacturer recommends that users with

concerns contact technical support.

Installation guidelines

Install the instrument:

• On a level surface

• In a clean, dry, well ventilated, temperature controlled location

• In a location with minimum vibrations that has no direct exposure to sunlight

• In a location where there is sufficient clearance around it to make connections and to do

maintenance tasks

• In a location where the power button and power cord are visible and easily accessible

Connect to external devices (optional)

The instrument has three USB 1.1 ports and one Ethernet port. Refer to Figure 1 on page 8.

English

9

USB type A port—Connect to a printer, barcode handset scanner, USB flash drive, keyboard

3

or

SIP 10 module.

USB type B port—Not used.

Ethernet port—Connect to a LAN with a shielded cable (e.g., STP, FTP, S/FTP). The maximum

length of the shielded cable is 20 m (65.6 ft). To set up a LAN connection at the instrument, refer to

the expanded user manual on the manufacturer's website .

Note: USB cables must not be longer than 3 m (9.8 ft).

User interface and navigation

The instrument display is a touch screen. Only use a clean, dry finger tip to navigate the functions of

the touch screen. Do not use writing tips of pens or pencils or other sharp objects to make selections

on the screen or damage to the screen will occur.

Refer to Figure 3 for an overview of the home screen.

Figure 3 Display overview

1 Sample ID and measurement number

4

7 UP/DOWN navigation arrows

2 User comments 8 Sidebar menu (refer to Table 2)

3 Instructions 9 Time and date

4 Turbidity value, unit and reading mode 10 Options button

5 Warning or error message 11 Read button

6 Calibration status icon and calibration curve 12 Information (help) button

3

As an alternative to the touchscreen, use a keyboard to enter text into text boxes on the display

(e.g., passwords and sample IDs).

4

The measurement number increases by one each time a measurement is completed.

10 English

Table 2 Sidebar menu icons

Icon Description

Login

Logs in or logs out an operator. To log in, select an operator ID and then push Login. To log out,

push Logout.

Note: When an operator is logged in, the Login icon changes to the icon selected for the operator ID (e.g., fish,

butterfly or soccer ball) and the text "Login" changes to the operator ID.

Sample ID

Selects the sample ID.

Calibration

Starts a calibration.

Verification

Starts a verification.

Link2SC

Compares process and laboratory measurements.

Data Log

Shows the reading log, calibration log, verification log and compare log. Refer to Show the

recorded data on page 18.

Setup

Configures the instrument settings. Refer to Configure the instrument settings on page 12.

Diagnostics

Shows the firmware information, instrument backup, instrument updates, signaling information and

factory service data.

Timer

Sets a timer.

Goes to the manufacturer's website for the latest software versions and user manual when the

instrument has a LAN connection.

Documents

Shows the user manual and video(s) for the instrument.

Startup

C A U T I O N

Personal injury hazard. Never remove covers from the instrument. This is a laser-based instrument and

the user risks injury if exposed to the laser.

English 11

C A U T I O N

Personal injury hazard. Do not look into the vial compartment when the instrument is connected to

power.

Refer to the illustrated steps that follow to connect power to the instrument and start the instrument.

When the language menu shows, select the language and then push OK. The self-check will start.

Note: To change the language after the initial startup, refer to Change the language on page 13.

Operation

Configuration

Configure the instrument settings

1. Push two times, then push Setup.

2. Select an option.

Option Description

Location Sets the location name of the instrument. The location is saved with measurements to the

data log.

Date & Time Sets the date format, the time format and the date and time. Enter the current date and

time. Date Format—Sets the date format. Options: dd-mmm-yyyy (default), yyyy-mm-dd,

dd-mm-yyyy or mm-dd-yyyy. Time Format—Sets the time format. Options: 12 or

24 hours (default).

Security Enables or disables password protection for the settings and tasks in the security list.

Security Password—Sets or changes the security (administrator) password

(10 characters maximum). Passwords are case sensitive. Security List—Sets the

security level for each setting and task in the security list.

• Off—All operators can change the setting and or do the task.

• One key—Only operators with a one-key or two-key security level can change the

setting or do the task. Refer to Add operator IDs on page 13.

• Two keys—Only operators with a two-key security level can change the setting or do

the task.

Note: The Security setting is not set to on until Close is pushed.

Sound Settings Enables or disables the sound settings for individual events. Sets the sound volume for

each event (1 to 10). To enable or disable all of the sound settings, select All and then

push Setup.

12 English

Option Description

Network &

Peripherals

Shows the connection status of the devices that are directly connected to the instrument

and connected to the instrument by LAN (local area network).

• Printer—Local printer or network printer

• Network—LAN connection

• Controller—sc controller(s)

• PC

• USB Memory—USB flash drive

• Keyboard

Power

Management

Sets when the instrument is automatically set to sleep mode or off after a period of no

activity. Sleep Timer—Sets when the instrument is set to sleep mode. Options: OFF,

30 minutes, 1 (default), 2 or 12 hours. Power-Off Timer—Sets when the instrument is set

to off. Options: OFF, 2, 6, 12 (default) or 24 hours.

Change the language

N O T I C E

Wait a minimum of 20 seconds after the power is set to off before the power is set to on again or damage to the

instrument can occur.

To change the language after the initial startup, do the steps that follow.

1. Set the instrument to off.

2. Set the instrument to on.

3. During startup, touch the display until the language menu shows (approximately 45 seconds).

4. When the language menu shows, select the language and then push OK.

Add operator IDs

Add a unique operator ID for each person who will measure samples (30 maximum). Select an icon,

operator password and security level for each operator ID.

1. Push Login.

2. Push Options>New.

3. Enter a new operator ID (10 characters maximum), then push OK.

4. Push the LEFT and RIGHT arrows to select the icon for the operator ID (e.g., fish, butterfly or

soccer ball).

5. Push Operator Password, then enter a password for the operator ID.

Note: Passwords are case sensitive.

6. Push Security Level, then select the security level for the operator ID.

• Off—The operator cannot change the settings or do the tasks in the Security settings that have

a security level of one key or two keys.

• One key—The operator can change all the settings and do all the tasks in the Security settings

that have a security level of off or one key.

• Two keys—The operator can change all the settings and do all the tasks in the Security

settings.

Note: Before a security level can be selected, the Security setting must be set to on. Refer to Configure the

instrument settings on page 12.

7. Push OK>Close.

8. To edit an operator ID, select the operator ID and then push Options>Edit.

9. To delete an operator ID, select the operator ID and then push Options>Delete>OK.

English

13

Configure an operator RFID tag (optional)

To use an operator RFID tag to log in to the instrument, save the applicable operator ID to an

operator RFID tag as follows:

1. Push Login.

2. Select the operator ID, then push Options>Initialize RFID Tag.

3. Enter the password for the operator ID as necessary.

4. Complete the steps that show on the display.

5. Push OK to replace the operator ID on the RFID tag with a new operator ID if applicable.

6. Push Close.

7. Put the operator RFID tag in front of the RFID module to log in.

Add sample IDs

Add a unique sample ID for each sample (100 maximum). The sample ID identifies the sample

location or other sample specific information.

As an alternative, import sample IDs from a spreadsheet file to the instrument. Refer to the expanded

user manual on the manufacturer's website to import sample IDs.

Note: When a sample bottle with a sample RFID sticker is put in front of the RFID module, the sample ID is

automatically added to the instrument and selected on the instrument.

1. Push Sample ID.

2. Push Options>New.

3. Enter a new sample ID (20 characters maximum).

4. If the sample bottle has a barcode that identifies the sample ID, read the barcode with a barcode

handset scanner that is connected to the instrument. The barcode is added to the sample ID.

5. Push OK.

6. Select an option.

Option Description

Add Date/Time Adds the data and time that the sample was collected to the sample ID (optional). The date

and time entered for each sample ID show on the Sample ID menu.

Add Number Adds a measurement number to the sample ID (optional). Select the first number used for

the measurement number (0 to 999).

The measurement number shows in parenthesis after the sample ID on the home screen.

Refer to Figure 3 on page 10.

Add Color Adds a colored circle to the sample ID icon (optional). The sample ID icon shows before the

sample ID on the home screen. Refer to Figure 3 on page 10.

7. Push OK>Close.

8. To edit a sample ID, select the sample ID and then push Options>Edit>OK.

9. To delete a sample ID, select the sample ID and then push Options>Delete>OK.

14

English

Configure the measurement settings

Select the reading mode, measurement units, data log settings, resolution and more.

1. At the main reading screen, push Options>Reading Setup.

2. Select an option.

Option Description

Reading Sets the reading mode to single, continuous or minimum mode. Default: Single. Single—

The measurement stops when the reading is stable. Continuous—The measurement

continues until the user pushes Done. Minimum Mode—Set to on when a process and

laboratory measurement are compared and the process measurement is a lower NTU

range. Removes the effect of non-representative particles in the grab sample. Signal Avg

—The turbidity reading that shows on the display is an average of the values measured

during the time interval selected. Options: For single measurement mode, 5 to 15 seconds.

For continuous measurement mode, 5 to 90 seconds.

Unit Selects the measurement units that show on the display and that are recorded to the data

log. Options: NTU, FNU, TE/F, FTU, EBC, mNTU or mFNU. Default: NTU ).

Data Log

Setup

Sets the data log settings. Auto Store—Measurement data is automatically recorded in the

reading log. Default: On. When not selected, push Options>Store to record the current

measurement to the reading log as necessary. Send Data Format—Sets the output format

of measurement data that is sent to external devices (CSV or XML). Default: XML. Print

Format—Sets the output format of measurement data that is sent to a printer (Quick Print

or Detailed Print (GLP)). Comments—Lets users add comments to log entries. Auto Send

—Measurement data is automatically sent to all of the devices (e.g., printer, USB flash

drive and FTP server) that are connected to the instrument after each measurement.

Resolution Selects the number of decimal places that show on the display. Options: 0.001 (default) or

0.0001.

Bubble Reject Sets the bubble reject to on (default) or off. When set to on, high turbidity readings caused

by bubbles in the sample are not shown or saved to the data log.

Close lid to

start reading

Enables or disables the instrument to start a measurement automatically when the lid is

closed. Default: On. A measurement is only done when there is a sample vial in the

instrument.

Set the acceptance range

Before process and laboratory measurements are compared on the instrument, set the acceptance

range for the compare results. The acceptance range is the maximum difference permitted between

the process and laboratory measurements.

1. Push LINK2SC.

2. Push Options>Compare Setup.

3. Push Acceptance Range>Unit.

4. Select an option.

Option Description

% Sets the acceptance range to a percentage (1 to 99%).

NTU Sets the acceptance range to NTU units (0.015 to 100.00 NTU).

5. Push Value, then enter the acceptance range.

Measurement

Sample collection

• Collect samples in clean glass or plastic bottles with tight-fitting caps.

• Rinse the container a minimum of three times with the sample.

English

15

• When collecting a sample from a water tap in a distribution system or treatment plant, turn the

water on for at least five minutes, then collect the sample. Do not adjust the flow because this can

add particles.

• When collecting a sample from a body of water (e.g., a stream or storage tank), collect at least one

liter (1 quart) and fully mix before taking an aliquot for measurement. If the quality of the sample

source is not constant, collect samples at many locations at different depths as necessary. Then,

mix the samples together to prepare one sample for measurement.

• Fill the container. Let the container overflow with the sample and then immediately put the cap on

the sample container so that there is no headspace (air) above the sample.

• Write the sample information on the container.

• Start analysis as soon as possible to prevent temperature changes, bacteria growth and settling.

Prevent vial contamination

N O T I C E

Do not to touch or scratch the glass of the sample vial. Contamination or scratches on the glass can cause

measurement errors.

The glass must stay clean and have no scratches. Use a no-lint cloth to remove dirt, fingerprints or

particles from the glass. Replace the sample vial when the glass has scratches.

Refer to Figure 4 to identify where not to touch the sample vial. Always keep the sample vials in the

vial stand to prevent contamination on the bottom of the vial.

Figure 4 Sample vial overview

1 Measurement surface—Do not touch.

Prepare a sample vial

C A U T I O N

Chemical exposure hazard. Dispose of chemicals and wastes in accordance with local, regional and

national regulations.

N O T I C E

Always put a cap on the sample vial to prevent spills in the vial compartment.

Refer to the illustrated steps that follow to prepare a sample vial for measurement. Measure the

sample immediately.

Note: If there is contamination in the sample vial after it is rinsed with the sample, clean the sample vial. Refer to

Clean a sample vial on page 21.

16

English

Put the vial in the instrument

C A U T I O N

Personal injury hazard. Never remove covers from the instrument. This is a laser-based instrument and

the user risks injury if exposed to the laser.

C A U T I O N

Personal injury hazard. Do not look into the vial compartment when the instrument is connected to

power.

N O T I C E

Keep the lid closed to keep contamination out of the vial compartment.

English 17

1. Log in to the instrument as follows:

• Put an operator RFID tag in front of the RFID module or

• Push Login. Select the applicable operator ID, then push Select.

2. Select the sample ID as follows:

• Put the sample RFID sticker on the sample bottle in front of the RFID module or

• Push Sample ID. Select the applicable sample ID, then push Select.

Note: To add sample IDs to the instrument, refer to Add sample IDs on page 14.

3. Clean the sample vial with a no-lint cloth to remove contamination.

4. Dry the external surfaces of the vial with a no-lint cloth. Make sure to dry the bottom of the vial.

5. Put the sample vial in the vial compartment. Refer to the illustrated steps that follow.

Measure the sample

1. Push Read if a measurement does not start automatically when the lid is closed.

2. When the measurement is complete, push Options>Store to record the measurement to the

reading log as necessary.

Note: If the Auto Save setting is set to on, "Data Stored" shows on the display and the measurement is

automatically recorded to the reading log.

3. To show the recorded measurements, push Options>Reading Log. Refer to Show the recorded

data on page 18 for more options.

4. To send the measurement data to external devices that are connected to the instrument, push

Options>Send Data. Refer to Show the recorded data on page 18 for more options.

Note: If the Auto Send settings is set to on, the measurement data is automatically sent to the external

device(s) that is connected to the instrument.

Compare process and laboratory measurements

Refer to the expanded user manual on www.hach.com to compare process and laboratory

measurements.

Show the recorded data

All the recorded data is kept in the data log. The data log is divided into four logs:

• Reading log—Shows the recorded measurements.

• Calibration log—Shows the calibration history.

• Verification log—Shows the verification history.

• Compare log—Shows the recorded comparisons of process and laboratory measurements.

18

English

1. Push Data Log and select the applicable log to show.

2. To show the details of a log entry, select the log entry and then push View Details.

Note: To add a comment to the log entry, push the comments icon.

3. To only show the log entries recorded during a time interval or with a specific operator ID or

sample ID, do the steps that follow.

a. Push Filter, then select On.

b. Select an option.

Option Description

Time Interval Selects the time interval.

Operator ID Selects the operator ID.

Sample ID Selects the sample ID. This option only shows when Reading Log or Compare Log is

selected.

4. To send log data to a device (e.g., printer or USB flash drive), delete a log entry or show a

compare log or reading log entries in a graph, do the steps that follow.

a. Push Options.

b. Select an option.

Option Description

Delete Removes one of the items that follow.

• The selected log entry

• The log entries for a time interval

• The log entries with a specific operator ID

• The log entries with a specific sample ID

5

• All the entries in the selected log

Send

Data

Sends one of the items that follow to all the devices that are directly connected to the

instrument (e.g., printer or USB flash drive) and connected to the instrument by LAN (network

printer or FTP server).

• The selected log entry

• The log entries for a time interval

• The log entries with a specific operator ID

• The log entries with a specific sample ID

5

• All the entries in the selected log

View

Graph

Shows the reading log entries that have the same sample ID in a graph. This option only

shows when Compare Log or Reading Log is selected.

To add the log entries for another sample ID to the graph, push Options>Add Data. Select a

sample ID to add to the graph.

To show the details of a data point, touch a data point on the display or push the LEFT and

RIGHT arrows to select a data point.

Data points—Selects the symbol used for the data points. Control Limit—Sets the

minimum value and maximum value of the readings that show on the graph.

5

This option only shows when Reading Log or Compare Log is selected.

English 19

Calibration

W A R N I N G

Chemical exposure hazard. Obey laboratory safety procedures and wear all of the personal protective

equipment appropriate to the chemicals that are handled. Refer to the current safety data sheets

(MSDS/SDS) for safety protocols.

When the instrument is used for US EPA regulatory reporting, calibrations must be done according to

US EPA guidance documents and methodologies. Contact local regulating authorities for additional

compliance regulations.

The instrument is factory calibrated and the laser light source is stable. The manufacturer

recommends that a calibration verification be done periodically to make sure that the system

operates as intended. The manufacturer recommends calibration after repairs or comprehensive

maintenance work.

Refer to the expanded user manual on the manufacturer's website to calibrate the instrument and do

a calibration verification.

Maintenance

C A U T I O N

Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the

document.

C A U T I O N

Chemical exposure hazard. Obey laboratory safety procedures and wear all of the personal protective

equipment appropriate to the chemicals that are handled. Refer to the current safety data sheets

(MSDS/SDS) for safety protocols.

C A U T I O N

Personal injury hazard. Never remove covers from the instrument. This is a laser-based instrument and

the user risks injury if exposed to the laser.

N O T I C E

Do not disassemble the instrument for maintenance. If the internal components must be cleaned or repaired,

contact the manufacturer.

Clean spills

C A U T I O N

Chemical exposure hazard. Dispose of chemicals and wastes in accordance with local, regional and

national regulations.

1. Obey all facility safety protocols for spill control.

2. Discard the waste according to applicable regulations.

20

English

ページを読み込んでいます...

Hach TU5200 Basic User Manual

Hach TU5200 Basic User Manual

他の言語で

関連論文

その他の書類